Interactive Monitor Arm

Size: px
Start display at page:

Download "Interactive Monitor Arm"

Transcription

1 Interactive Monitor Arm Tools Required -5mm Allen wrench -Phillips screwdriver -Plastic mallet There are two ways to attach a Monitor Arm to a Full Frame; with a Beam, or with a Post Mount. Both methods are incuded in these instructions. Post Mount Monitor Arm Mount Beam Mount MONITOR ARM MOUNT-POST NOTE: The Post Mount can be placed on any side by side rows of trapezoidal holes. Once in place, it is ready for the monitor arm. Full frame Monitor arm mount (post) 1. Select the desired position for the Post Mount. Next, insert the hooks located on the back of the Post Mount into the slots in the post. To assure that the hooks are firmly seated, tap the top of the Post Mount with a Plastic mallet or equivalent. See Figure 1. Trapezoid slots MONITOR ARM MOUNT-BEAM NOTE: The Beam is attached to posts spaced to correspond with the length of the beam ordered. There are 24, 30, 36, 42, 48, 60, and 72 Beams. Beams require a separate Monitor Arm Mount. Trapezoid slots Figure 1 Full frame Monitor arm mount (beam) 1. Select the desired position for the Beam. Next, insert the hooks located on the back of the Beam into the slots in the posts. To assure that the hooks are firmly seated, tap the top corners of the Beam with a plastic mallet or equivelent. See Figure Hang the Monitor Arm Mount on the Beam and lock it in place by attaching the Retainer bar with two #10-24 x 1.00 Socket head cap screws. See Figure 3a and 3b. Hooks Beam Figure 2 Beam Figure 3a Retainer bar Beam Beam Mount Figure 3b #10-24 x 1.00 Socket head cap screws P-1

2 Interactive Monitor Arm (cont.) ATTACHING THE MONITOR PLATFORM 3. Place the thin plastic washer (packaged with the short arm) over the 1.18 dia. pin on the Post or Beam Mount. See Figure If you have the long arm version, assemble the arm extension to the short arm. The thin washer (packaged with the arm extension) goes over the 5/8 pin. 5. The Monitor Platform drops into the end of the arm. Be sure two large black nylon spacers are on the platform pin before inserting. Secure that assembly by inserting the M8 screw with the lock washer and countersunk trim washer into the end of the 5/8 pin. Do not over tighten. Insert the pin of the extension into the end hole of the short arm. Secure that assembly by inserting the M8 screw, the lock washer, and countersunk trim washer into the end of the 5/8 pin. Do not tighten ; The arm must rotate. ADJUSTMENTS If rotated clockwise, the Monitor Platform will tighten itself. If this happens, turn it counter clockwise 360 degrees or until loose. The platform should now turn freely within your operating radius. The Monitor Platform has three adjusting knobs underneath. These are for leveling the platform if the monitor is tipped slightly in any direction. By loosening and tightening the knobs in some order, level can be attained. For example. if the monitor leans to the left (low side), loosen the low side knob(s) and tighten the high side drawing it down. Monitor platform Adjusting knobs Platform pin Support arm (short arm shown) Nylon spacers Lock washer Countersunk washer M8 Screw 1.18 Pin Thin plastic washer Post/beam mount Figure P-2

3 Interactive Monitor Arm (cont.) Parts List Part Number Description Qty X Post Mount Assembly Arm Mount Asembly X 3162X 24 Beam 30 Beam X 36 Beam X 3166X 3167X 48 Beam 60 Beam 72 Beam X Retainer Bar #10-24 x 1.00 Socket Head Cap Screw X Monitor Arm Platform Assembly Support Arm A Support Arm B P-3

4 Articulating Arm/ Components Articulating Arm/Components IMPORTANT SAFETY INSTRUCTIONS 1. Do Not exceed the maximum weight load capacity for any component. Component Monitor Platform Tool Tray Bin Board Peg Board Document Holders Maximum Capacity 60 Lbs. 30 Lbs. 30 Lbs. 20 Lbs. 20 Lbs. 2. Do Not install a Monitor Platform, Tool Tray or Bin Board on the 24 or 30 wide free standing TechBench or Linx Worksurface. They may cause the unit to tip if they are fully loaded and extended to one side. The Bench or Worksurface must be securely attached to an adjacent unit to prevent potential tipping. 3. Do Not extend the components beyond the back of the 24, 30 or 36 wide TechOrganizers on Linx Worksurfaces as the unit may tip. 4. Always ensure that the articulating arm is secured to the TechOrganizer or Full Frame using the #10-24 x 3/8 thread forming screw provided. Please read these instructions carefully and follow the installation steps in sequence. Tools Required - Phillips head screwdriver - 3/16 Allen wrench (provided) -5/32 Allen wrench (provided) - Rubber mallet ATTACHING COMPONENTS TO ARM Monitor Platform 1. Remove the 5/16-18 x 1/2 Button head cap screw and washer from the shaft located on the bottom of the Monitor Platform. Use the 3/16 Allen wrench provided. See Figure 1. Monitor Platform P-4

5 Articulating Arm/ Components (cont.) ATTACHING COMPONENTS TO ARM (cont.) 2. Slide the end of the Articulating Arm assembly with the thru hole onto the Platform shaft. See Figure 1. Note: Ensure that the two flange bearings on the Arm are in place. Articulating arm assembly 3. Attach the Arm to the Platform shaft using the 5/16-18 x 1/2 Button head cap screw and washer. Do not overtighten. See Figure 1. Bin/Peg/White Boards, Tool Tray etc. 1. Remove the following from the factory assembled component. See Figure 2. 5/16-18 x 1/2 Button head cap screw.34 I.D. x.69 O.D. Washer (2) 5/16-18 x 1/2 long Button head cap screws (2).34 I.D. washers (1).50 I.D. washer (1).50 dia. x 2.42 long pin Figure 1 2. Align the holes in the end of the Articulatng Arm with the holes in the pivot/swivel which is attached to the back of the component. See Figure 2. Note: Ensure that the two flange bearings are in place. IMPORTANT: Do not push the.50 dia. pin thru the entire assembly until the.50 I.D. washer is inserted between the bottom flange bearing on the Arm and inside surface of the pivot/swivel. Articulating Arm w/ White Board 3. Attach the Arm to the pivot/swivel using the 5/16-18 x 1/2 Button head cap screws with washers. Tighten them with the 3/16 Allen wrench. 1/2 Dia. x 2.42 long pin.34 I.D. washer 5/16-18 x 1/2 Button head cap screw Component Pivot swivel Arm end 1/2 I.D. washer.34 I.D. washer P-5 Figure 2 5/16-18 x 1/2 Button head cap screw

6 Articulating Arm/ Components (cont.) INSTALLING THE COMPONENT The Articulating Components may be installed on TechOrganizers or LMS Frames. 1. Determine the desired location on the Organizer/ Frame and insert the hooks on the back of the Articulating Arm mounting bracket into the slotted standard. See Figure Ensure that the mounting bracket is fully seated in the slotted standard by tapping it down with a rubber mallet. 3. Secure the mounting bracket to the standard using the #10-24 x 3/8 phillips pan head thread forming screw provided. See Figure Snap the plastic Cover onto the bottom of the bracket. Note: The top cover is factory installed. To remove the cover, use a flat blade screwdriver in the slot provided. Slotted standard TechBench with White Board Slot for removal with screwdriver Articulating arm mounting bracket #10-24 x 3/8 phillips pan head thread forming screw Figure 3 Cover OPTIONAL MOUSE PLATFORM The Mouse Platform can be installed on the left or right side of the Monitor Platform. Tools Required - 5/32 Allen wrench (provided) 1. Determine the installation side and remove the two plastic hole plugs from the Monitor Platform. See Figure Attach the Mouse Platform to the Monitor Platform using the 1/4-20 x 3/8 Button head cap screws and 1/4-20 hex nuts. Tighten securely. See Figure 4. 1/4-20 x 3/8 Button head cap screws 1/4-20 hex nuts w/lock washers Mouse platform Plastic hole plugs Monitor platform Figure P-6

7 Articulating Arm/ Components (cont.) OPTIONAL KEYBOARD TRAY 1. Remove the three plastic hole plugs from the front of the Monitor Platform. Align the three holes at the rear of the Keyboard Tray with the three holes in the Monitor Platform and insert three 1/4-20 x 3/8 button head cap screws. Secure the screws with three 1/4-20 hex nuts with lock washers. See Figure 5. Keyboard Tray 1/4-20 hex nuts w/lock washers Monitor platform Keyboard tray 1/4-20 x 3/8 button head cap screws Figure 5 ADJUSTING COMPONENTS 5/16-18 x 1/2 Button head cap screw 1. The ease with which a joint pivots can be adjusted by tightening or loosening the 5/16-18 x 1/2 Button head cap screws at each joint. See Figure The incline/tilt of a component can be adjusted using the Hand Adjustment Lever(s). See Figure 7. Note: Pull the lever out to rotate it clockwise. Articulating arm assembly Figure 6 Hand adjustment lever Figure P-7

8 Articulating Arm/ Components (cont.) OPTIONAL FLAT SCREEN MONITOR 1. Assemble the Flat Screen Monitor as shown in figure 8. Flat screen monitor 5/16 Thrust bearing 5/16-18 x 3/4 Socket Head cap screw 5/16-18 x 1/2 Button head cap screw.34 I.D. washer 1/2 Dia. x 2.42 long pin Pivot swivel 5/16-18 Nut w/nylon 1/2 I.D. washer 5/16 Belleville washer Mounting plate 5/16 Nylon washer.34 I.D. washer 5/16-18 x 1/2 Button head cap screw Figure 8 ARTICULATING ARM VARIATIONS The Articulating Arm can be configured in the various ways shown at right depending on your specific requirements. Full Arm - Factory Assembled Reversed Arm Sections Long Arm Only P-8

9 Articulating Arm/ Components (cont.) Parts List Parts List Part Number Description Qty. Part Number Description Qty X Mounting Bracket X 6.22 Arm X Rectangular Tube 1.00 x 2.00 x Flange Bearing /16-18 x 1/2 Button Head Cap Screw Plain Washer Pin X Cover X End Cap #10-24 x 3/8 Phillips Pan Head Thread Forming Screw Hole Plug Handle w/hardware Rubber Pad X Monitor Platform X Mouse Platform /4-20 x 3/8 Button Head Cap Screw /4-20 Hex Nut w/lock Washer Wide White Board/Document Holder 7527X 20 Wide Document Holder Wide White Board/Document Holder X 11 Wide Document Holder X 15 x 15.5 Peg Board 7528X 15 x 15.5 Bin Board 7530X 11 x 17.8 Tool Tray Leveler Knob X Pivot Plate X 75mm Mounting Plate 9554X 100mm Mounting plate /16-18 x 3/4 Socket Head Cap Screw /16 Nylon Washer /16 Belleville Washer /16 Thrust Bearing /16-18 Nut w/nylon X Bracket X Keyboard Tray Pad, x Washer - SAE 1/ X Pivot/Swivel Bracket Cap Nut Adjustable Hand Lever /4-20 x 1.00 Carriage Bolt Lock Washer I.D. x.62 O.D. Washer Spacer Shaft P-9

10 Articulating Arm/ Components (cont.) P-10

11 Articulating Arm/ Components (cont.) P-11

12 Task Light Tools Required -Phillips head screwdriver Task Lights are available in (4) sizes and can be installed on various size shelves per the following matrix. The holes for installation are pre-punched. Shelf Task Light 24 Tower/Electric/G.P Shelf - 18 centered 30 Tower/Electric/G.P Shelf - 18 centered, 24 centered Task Light 36 Tower/Electric/G.P Shelf - 18 centered, 24 centered 42 Tower/Electric/G.P Shelf - 24 centered, 36 centered 48 Tower/Electric/G.P Shelf - 24 centered, 36 centered 60 Tower/Electric/G.P Shelf - 24 L/R/C, 36 centered. 48 centered 72 Tower/Electric/G.P Shelf - 24 L/R/C, 36 centered, 48 centered 24 Locking Compartment - 18 centered 30 Locking Compartment - 18 centered, 24 centered 36 Locking Compartment - 18 centered, 24 centered 42 Locking Compartment - 18 centered, 36 centered 48 Locking Compartment - 18 centered, 36 centered TASK LIGHT INSTALLATION 1. Locate any two screw holes in the Shelf Stiffener that are on the folowing centers. #10 Phillips head screws (back out 1/16 ) 18 Task Light - 10 centers 24 Task Light - 16 centers 36 Task Light - 28 centers Shelf stiffener 48 Task Light - 40 centers Install two #10 x 3/8 Phillips head sheet metal screws partially into the holes, leaving them protruding approximately 1/16. See Figure 1. Figure Q-1

13 Task Light (cont.) 2. Remove the lens and bulb from the Task Light. To remove the lens, push it up near the front edge of the Task Light fixture. See Figure 2. Remove bulb by rotating it in either direction and then pulling it away from the mounting sockets. Task light housing Bulb Mounting socket 3. Position the Task Light fixture against the Shelf stiffener with the mounting screws protruding thru the large ends of the key hole slots. Push the fixture toward the back of the Shelf to seat the screws into the narrow portion of the slots and then tighten the screws. See Figure Now replace the bulb and the lens. The corrugated surface of the lens is toward the bulb. See Figure 3. Cable Clips are provided to route and secure the Task Light cord. NOTE: Fixture must be plugged into a three pronged grounded outlet. Push here Figure 2. Removing lens and bulb Push here first Lens Corrugated surface Figure 3. Replacing lens and bulb Screws Shelf stiffener key hole slot Task light Cable clip Cord Figure Q-2

14 Overhead Lighting Tools Required - Plastic mallet - 5/32 Hex Wrench (provided) - 1/2 Wrench or socket - Phillips head screwdriver There are three types of Overhead Lighting Support Brackets. The Low Profile version (when hooked in the top trapezoids of a Standard) is below the top of the Full Frame, the High Profile version that is 12 above, and the Rear Mount version which is also 12 above the top of the Full Frame. In addition to the light, the Overhead Brackets support an optional Tool Track. The attachment options vary with Full Frame width (left side, right side), the size of the light, and your height preference. Overhead Lighting High Profile Support Bracket Low Profile Support Bracket Rear Mount Support Bracket Full Frame 1. Select the position you prefer and hook on the first Support Bracket. Space the second Bracket based on the frame modules and light size ( 36, 48, etc.). Tap the Brackets down, making sure the hooks are seated into the frame. Secure the Brackets by driving the #10-24 x 3/8 screws (provided) into the hole at the bottom of each Bracket. See Figure 1. Support bracket #10-24 x 3/8 Pan head screw Figure Q-3 1

15 Overhead Lighting (cont.) Mounting spacer 1/4-20 x 1/2 Button head screws Figure 2 Spacer flange Overhead light #10-24 x 3/8 Pan head screw Figure 2 Overhead light 2. Packaged with the Light Support Brackets are two Mounting Spacers for the light which are in a separate carton. Attach a Spacer to each end using three x 3/8 screws for each. See Figure Position the light between the Support Brackets with the Spacer flange above the Brackets. Rest the light on the Brackets. There are three positions, front to back, for the light. Select one by aligning the Spacer holes with Bracket holes and attach with two 1/4-20 x 1/2 Button head screws at each end. See Figure 3. TOOL TRACK ATTACHMENT Support bracket Support bracket Figure 3 1. The Tool Track attaches to the under side of the Light Support Brackets at the front. Align the hole in the Tool Track with the hole in the Support Bracket and drive one 1/4-20 x 1/2 screw and lock washer into the end of each Bracket. Screws at both ends should be started before tightening either one. See Figure Insert one End Stop, #83632, into the Tool Track (see Figure 4 for orientation). The straight plate is on the outside creating a sandwich or clamping attachment. Do Not tighten yet! End cap End stops Lock washer Tool track 1/4-20 x 1/2 Button head screw 3. Insert the Tool Trolley (not shown) next and then the second End Stop. Assemble the End Caps to each end. NOTE: If an End Cap strikes a screw head before seating fully into the tube, loosen the screw so that the End Cap slides under the head, then re-tighten. Or, trim the cap with scissors. Figure 4. Slide the End Stops to each end to a position just short of the End Caps and tighten Q-4 2

16 Overhead Lighting (cont.) Parts List Part Number 3807X Description Light Support, Low Profile Qty X Light Support, High Profile X Rear Mount Support Bracket X Spacer #10-24 x 3/8 Phillips Pan Head Thread Forming Screw /4-20 x 1/2 Button Head Screw /4 Lock Washer End Cap End Stop Tool Track, Tool Track, Tool Track, Tool Track, Tool Track, Q-5 3

17 Laminate Hook- on Shelves with Overhead Light Tools Required -Plastic mallet -Phillips head screwdriver 1. Determine the location of the Shelf and Overhead Light and install the shelf as outlined on page K-3. INSTALLING LIGHT USING SHELF SUPPORT BRACKET FASTENERS NOTE: Do not fully tighten the four screws attaching the shelf to the shelf supports; leave approximate 1/8 gap. See Figure Attach a Light Mounting Bracket to the underside of each shelf support. Align the keyhole slots in the brackets with the shelf attachment screws. Shift the brackets on the screws to bottom out in the keyhole slots. See Figure 2a. NOTE: 12 deep shelves use the two inner keyhole slots on 5 centers; 18 /24 deep shelves use the two outer keyhole slots on 11 centers. See Figure 2b. 3. Tighten all screws. Shelf Laminate Hook-on Shelves with Overhead Light 1/8 Shelf support (L.H. shown) Shelf Figure 1 Screws (underside) Keyhole slots Light mounting brackets Light mounting bracket Figure 2a Figure 2b Q-6

18 Laminate Hook- on Shelves with Overhead Light (cont.) INSTALLING LIGHT BETWEEN SHELF SUPPORT BRACKETS 4. Drill four.113 diameter holes (#33 drill).50 deep in the underside of the shelf per the hole pattern dimensions indicated, positioning the light in the desired location. Dim. X 36 Light Light Light Light Attach the Light Mounting Brackets to the underside of the shelf using four #10AB x 3/4 phillips pan head screws provided. See Figure 3. Shelf Light mounting brackets #10AB x 3/4 phillips pan Head screws Q-7

19 Laminate Hook- on Shelves with Overhead Light (cont.) 6. Install the light into the brackets with the on/off switch toward the front. See Figure 3. Light mounting brackets Overhead light Figure 3 Overhead light 7. Attach an End Stop to the front of each light mounting bracket using the #10-24 x 3/8 thread forming screws provided. See Figure 4. End stop Light mounting bracket #10-24 x 3/8 phillips pan head thread forming screws Figure Q-8

20 Laminate Hook- on Shelves with Overhead Light (cont.) Parts List Part Number Description Qty. 2993X Laminate Shelf, 36 x X Laminate Shelf, 48 x X Laminate Shelf, 60 x X Laminate Shelf, 72 x X Laminate Shelf, 36 x X Laminate Shelf, 48 x X Laminate Shelf, 60 x X Laminate Shelf, 72 x X Laminate Shelf, 36 x 18 ESD 3852X Laminate Shelf, 48 x 18 ESD 3853X Laminate Shelf, 60 x 18 ESD 3854X Laminate Shelf, 72 x 18 ESD Parts List Part Number Description X 8 x 11 Shelf Support - L.H., 12 Deep Shelf X 8 x 11 Shelf Support - R.H., 12 Deep Shelves X 8 x 17 Shelf Support - L.H., 18 /24 Deep Shelves X 8 x 17 Shelf Support - R.H., 18 /24 Deep Shelves #10AB x 5/8 Phillips Pan Head Thread Forming Screw #10-24 x 3/8 Phillips Pan Head Self Tapping Screw Qty X Light Mounting Bracket X End Stop #10AB x 3/4 Phillips Pan Head Screws X 3859X 3860X 3861X Laminate Shelf, 36 x 24 ESD Laminate Shelf, 48 x 24 ESD Laminate Shelf, 60 x 24 ESD Laminate Shelf, 72 x 24 ESD 2986X Laminate Shelf, 36 x X Laminate Shelf, 48 x X Laminate Shelf, 60 x X Laminate Shelf, 72 x X 3845X 3846X 3847X Laminate Shelf, 36 x 12 ESD Laminate Shelf, 48 x 12 ESD Laminate Shelf, 60 x 12 ESD Laminate Shelf, 72 x 12 ESD Q-9

21 Laminate Hook- on Shelves with Overhead Light (cont.) Q-10

22 ESD Laminate WARNING: Electro static discharge can be dangerous to equipment and to persons if not properly dissipated. Read this supplement thoroughly for information on grounding precautions as well as general care and maintenance. It is recommended that the ESD Top be grounded by a certified electrician and tested before it is used. It is important to insure a proper ground to minimize the possibility of damage to equipment and person. ESD GROUNDING 1. The point of ground for the ESD Top is installed at the factory. A Ground Wire should be attached to the Grounding Bolt with the other end attached to to the facility electrical ground. See Figure Each ESD Worksurface and Shelf comes with only one grounding point. Surfaces should be connected to ground in parallel and should not be connected to each other in series. When tightening the nut onto the Grounding Bolt, DO NOT OVER TIGHTEN. Hand tighten + 1/4 turn. Top of ESD worksurface 12 GA Ground wire Figure 1 Grounding bolt Ground point for ESD tops 3. Once the ESD ground is established, it is important to test the system. Periodic checks of the system are recommened to ensure the integrity of the system. Monitoring devices may be used to alert persons when the integrity of the system has been compromised. 4. Enviromental factors, especially temperature and humidity, have a drastic effect on the resistive properties of the ESD Worksurfaces. Improper grounding arrangement CARE AND MAINTENANCE 1. When cleaning the surface becomes necessary, it is important to use non-abrasive cleaners only. If the surface is stained, baking soda and water may be used to remove the stain but excessive scrubbing may damage the surface. 2. It is important that no film or residue be left on the surface of the ESD Top. Failure to thoroughly clean the surface will reduce the dissapative properties of the laminate. Proper grounding arrangement Figure 2 esdinstr R-1

23 ESD Laminate (cont.) Parts List Part Number Description Qty #8-32 x 1.00 Socket Flat Head Cap Screw Brass Insert Plain Type A Washer Keps Lock Nut GA Grounding Wire 1 1 esdinstr R-2

24 Grounding Bus Bar Tools Required -Electric drill with 7/32 drill bit -3/8 Wrench NOTE: The Grounding Bus Bar can be located anywhere on a Full Frame, but the recommended location is on top of the Frame bottom rail. It is also recommended that the Bus Bar be placed in the center of a Frame member. If Tech Walls are used, the Bus Bar will fit in between the panels. Grounding Bus Bar #LA Using the Bus Bar as a template, drill two.221 diameter holes into the Frame bottom rail. 2. Install the Bus Bar using the two 1/4-20 Self tapping hex washer head screws. See Figure GA. ground wire Bus bar 1/4-20 Self tapping screws Frame bottom rail Figure 1 Note: Locate bus bar in the center of frame bottom rail R-3 1

25 72 Bin Rail Tools Required -Phillips head screwdriver -Plastic mallet 1. Select the desired height for the Bin Rail. Attach the Bin Rail to the frame by inserting the hooks on the back of the Bin Rail into the trapeziodal slots in the Full Frame. See Figure 1. To assure that the hooks are fully seated, tap the top rear corners with a plastic mallet. See Figure Drive one #10 Phillips head screw (provided) into each end of the Bin Rail to lock it in place. See Figure and 72 Bin Rail NOTE: The maximum weight capacity of the Bin Rail is 200 lbs. Trapezoidal slots Full frame Bin rail Bin rail #10-24 x 3/8 Phillips head screw Figure 2 Figure 1 MF40 S-1

26 72 Bin Rail (cont.) Parts List Part Number Description Qty X 72 Bin Rail #10-24 x 3/8 Phillips Pan Head Screw 2 MF40 S-2

Linear Hook- on Worksurfaces

Linear Hook- on Worksurfaces Linear Hook- on Worksurfaces Linear Hook-On Worksurfaces come in three depths and seven lengths. Different worksurfaces have different reqirements for installation that are outlined below. 27 inch deep

More information

Technical Environment Systems INSTALLATION MANUAL

Technical Environment Systems INSTALLATION MANUAL Technical Environment Systems INSTALLATION MANUAL Technical Environment Systems INSTALLATION MANUAL Table of Contents INTRODUCTION Full Frame, Open Frame & Upright Assembly...A Foundations...B Mobile &

More information

LAN Locker Adjustable Shelves

LAN Locker Adjustable Shelves Adjustable Shelves LAN LOCKER ADJUSTABLE SHELVES * Adjustable Shelves are available for LAN LOCKER widths: 24, 30, 48, 60, and 72. * When installing more than one Adjustable Shelf, it is recommended that

More information

Modular Furniture LMS. Technical environment systems Installation manual

Modular Furniture LMS. Technical environment systems Installation manual Modular Furniture LMS Technical environment systems Installation manual Technical Environment Systems INSTALLATION MANUAL Table of Contents INTRODUCTION Full Frame, Open Frame & Upright Assembly...A Foundations...B

More information

F l a t S c r e e n A R M S I n s t a l l a t i o n

F l a t S c r e e n A R M S I n s t a l l a t i o n ITEM NUMBERS (1) #TOACAORG16 (2) #TOACAORG20 (3) #TOACATRP24 (4) #TOACATRP30 (5) #TOACATRPDS (6) #TOACATRPSS TOOLS REQUIRED (1) 3/8 Wrench (not provided) (2) Phillips head screwdriver (not provided) (1)

More information

IAC INDUSTRIES 895 BEACON STREET BREA, CA Phone (714) Fax (714) Workmaster Assembly Instructions

IAC INDUSTRIES 895 BEACON STREET BREA, CA Phone (714) Fax (714) Workmaster Assembly Instructions INDUSTRIES WORKMASTER SERIES Part #1 REV. (022011) IAC INDUSTRIES 895 BEACON STREET BREA, CA 92821-2926 Phone (714) 990-8997 Fax (714) 990-0557 www.iacindustries.com Workmaster Assembly Instructions Table

More information

Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens

Installation and Assembly - Universal Articulating Swivel Double-Arm for 42 - 60 Plasma Screens Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be

More information

Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens

Installation and Assembly - Universal Articulating Swivel Double-Arm for 42 - 60 Plasma Screens Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be

More information

Workbench Instructions for Assembly

Workbench Instructions for Assembly Workbench Instructions for Assembly Technical Electronic Workstations and Industrial Workbenches Includes: Cabinets Privacy Panels Stringers Bottom Shelves Table of Contents Tools Required for Assembly...

More information

TITAN2-EDGE Public Access Computer Station Dual Track

TITAN2-EDGE Public Access Computer Station Dual Track TITAN2-EDGE Public Access Computer Station Dual Track TITAN2-EDGE Rev A 6/17 Model TITAN2-EDGE ASSEMBLY AND ADJUSTMENT TITAN2-EDGE PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the

More information

PROFILE Flat Panel Console System Installation Manual

PROFILE Flat Panel Console System Installation Manual PROFILE Flat Panel Console System Installation Manual Table of Contents Page Introduction... 2 Important Safety Information...3, 4 Installation Overview... 4, 5, 6 Single Sided/Single Unit... 7 Double

More information

ABM International, Inc. Navigator Assembly Manual

ABM International, Inc. Navigator Assembly Manual ABM International, Inc. 1 1.0: Parts List Tablet (Qty. 1) Tablet mount (Qty. 1) NOTE: Mount may appear and operate different then image below Control Box (Qty. 1) Motor Power Supply (Qty. 1) 2 X-axis motor

More information

INSTALLATION INSTRUCTIONS HEAVY DUTY TILT WALL MOUNT Model: PPH-2000

INSTALLATION INSTRUCTIONS HEAVY DUTY TILT WALL MOUNT Model: PPH-2000 INSTALLATION INSTRUCTIONS HEAVY DUTY TILT WALL MOUNT Model: PPH-2000 Specifications: Accomodates Akira and Orion 84" displays without interface bracket; accomodates other large flat panel displays with

More information

OXYGEN INSTALLATION. Revision date

OXYGEN INSTALLATION. Revision date 12345 1 Hardware List 12345 Flat head wood screw #9 x 7/8 long with #2 Phillips drive, silver Used to attach surfaces and end panels Hex set screw ½-13 x 2 long with 1/4 hex drive, black Used on Legs Hex

More information

EPPA2-KIT DUAL MONITOR ARM CONVERSION

EPPA2-KIT DUAL MONITOR ARM CONVERSION EPPA2-KIT DUAL MONITOR ARM CONVERSION EPPA2-KIT Rev A 10/17 Model EPPA2-KIT-XXX ASSEMBLY AND ADJUSTMENT EPPA2-KIT PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the assembly and adjustment

More information

compile system INSTALLATION GUIDE Updated January 2019

compile system INSTALLATION GUIDE Updated January 2019 INSTALLATION GUIDE Updated January 09 compile system Table of Contents Panels 0 Quick Connect Clips 0 Lock Clips 0 Panel Trims 0 Privacy Glass 0 Post Base Covers 04 Electrical 04 Power Distribution Harness

More information

AndyMark DART 12.

AndyMark DART 12. AndyMark DART 12 Part Number Description QTY These Parts Are Pre-Assembled by AndyMark am-0031 Bearing, 3/16"ID (R3) 1 am-0209 Bearing, 3/8"ID 1614ZZ 2 am-1028 Screw, #10-32x3/8 Pan Head Philips 8 am-1121

More information

Warnings. Description. Prior to Installation Tools Needed

Warnings. Description. Prior to Installation Tools Needed Warnings Failure to act in accordance with the following may result in death or personal injury. The JT Strong Arm Stabilizer System is intended to eliminate chassis movement in travel trailers and fifth

More information

INSTALLATION INSTRUCTIONS DODGE RAM 2 & 4WD 1500 PART # P5058

INSTALLATION INSTRUCTIONS DODGE RAM 2 & 4WD 1500 PART # P5058 INSTALLATION INSTRUCTIONS 2009-13 DODGE RAM 2 & 4WD 1500 PART # P5058 PARTS LIST: Qty Description Qty Description 1 Grille Guard 12 12-1.75mm Hex Nuts 2 Upper Frame Mounting s (for trucks without tow hooks

More information

Assembly Instructions

Assembly Instructions InTandem Table System November 20 InTandem Table System - Worksurface #4 x/" 4 wood screw power beam Tools Provided T-0 Extended Torx Driver T-25 Torx Driver Additional Tools Required Soft protective

More information

Gared Pro-S Portable Backstop

Gared Pro-S Portable Backstop Models: 9616 & 9618 Installation, Operation and Maintenance Instructions Please read all instructions before attempting installation or operation of these units SAVE THESE INSTRUCTIONS FOR FUTURE USE PUBLICATION

More information

Paramount Enclosure. Installation Guide

Paramount Enclosure. Installation Guide Paramount Enclosure Installation Guide Wright Line LLC 160 Gold Star Boulevard Worcester, MA 01606 Tel: 800-225-7348 508-852-4300 Fax: 508-365-6178 info@wrightline.com All products and company names are

More information

TOOLS REQUIRED FOR ASSEMBLY. Rubber Mallet or Plastic Tip Hammer PARTS REQUIRED FOR ASSEMBLY OF SINGLE ENTRY STARTER.

TOOLS REQUIRED FOR ASSEMBLY. Rubber Mallet or Plastic Tip Hammer PARTS REQUIRED FOR ASSEMBLY OF SINGLE ENTRY STARTER. TOOLS REQUIRED FOR ASSEMBLY Rubber Mallet or Plastic Tip Hammer Top Cover Support PARTS REQUIRED FOR ASSEMBLY OF SINGLE ENTRY STARTER Back Stop Divider Closed 'L' Upright Slotted Reinforcement Support

More information

This instruction manual is an in-depth look and explanation of how to assemble and install the Murphy Bed properly and efficiently.

This instruction manual is an in-depth look and explanation of how to assemble and install the Murphy Bed properly and efficiently. This instruction manual is an in-depth look and explanation of how to assemble and install the Murphy Bed properly and efficiently. Don t be put off by the size of the instruction manual as the large diagrams

More information

OPERATOR'S MANUAL RULES FOR SAFE OPERATION

OPERATOR'S MANUAL RULES FOR SAFE OPERATION OPERATOR'S MANUAL #4950300 ROUTER AND JIG SAW MOUNTING KIT (FOR USE WITH THE BT3000 TABLE SAW) CONGRATULATIONS AND THANK YOU FOR BUYING THIS RYOBI ROUTER AND JIG SAW MOUNTING KIT. Your new #4950300 Router

More information

Eaton Data Center Racks

Eaton Data Center Racks Eaton Data Center Racks U 1. Product Overview In today's world, network equipment is one of the most important investments a business can make. How you store and protect this equipment is just as crucial.

More information

Franklin Mills Stackable Movable Lateral Instructions

Franklin Mills Stackable Movable Lateral Instructions Franklin Mills Stackable Movable Lateral Instructions Table of Contents: Table of contents...1 Tools Required...2 Stationary Shelving Assembly...3-7 Mobile Shelving Assembly...8-16 Rail Assembly...8-11

More information

Copyright Black Box Corporation. All rights reserved Park Drive Lawrence, PA Fax

Copyright Black Box Corporation. All rights reserved Park Drive Lawrence, PA Fax Copyright 2003. Black Box Corporation. All rights reserved. 1000 Park Drive Lawrence, PA 15055-1018 724-746-5500 Fax 724-746-0746 JULY 2003 RM3010A RM315-R2 RM323-R2 RM329 RM451 RM457 RM3020A RM316 RM324-R2

More information

Installation and Assembly - Articulating Swivel Double-Arm for 42" - 71" Plasma Screens

Installation and Assembly - Articulating Swivel Double-Arm for 42 - 71 Plasma Screens Installation and ssembly - rticulating Swivel Double-rm for 42" - 71" Plasma Screens Models: PLV 70, PLV 70-S R This product is UL Listed. It must be installed by a qualified professional installer. Maximum

More information

Installing flat panels on the MPL15 wall mount

Installing flat panels on the MPL15 wall mount Installing flat panels on the MPL15 wall mount The MPL15 (DS-VW775) is a full-service video wall mount that can accommodate tiled LCD panels with up to a 400 x 400 mm VESA pattern in portrait and landscape

More information

FlexFrame - Storage Components and Skins

FlexFrame - Storage Components and Skins FlexFrame - Storage Components and Skins 1/4 Square Drive Ball-Point Hex-Bit Socket 1/8 Short Hex, 1-1/2 Overall Length McMaster Part # 54075A44 Table of Contents Topic Page Storage Components 2 General

More information

INSTALLATION INSTRUCTIONS GRILLE GUARD RAM 1500 PART # 5058/5058-2

INSTALLATION INSTRUCTIONS GRILLE GUARD RAM 1500 PART # 5058/5058-2 INSTALLATION INSTRUCTIONS GRILLE GUARD PART # 5058/5058-2 PARTS LIST: Qty Description Qty Description 1 Grille Guard 8 12-1.75mm x 35mm Hex Bolts 2 Upper Frame Mounting s (for trucks without tow hooks

More information

Customer Notice: Congratulations again on your SawStop purchase, and thank you! -SawStop Tualatin, OR

Customer Notice: Congratulations again on your SawStop purchase, and thank you! -SawStop Tualatin, OR Customer Notice: Congratulations on the purchase of this Sliding Crosscut Attachment. As the owner of a SawStop saw, you are familiar with our high standards for quality, fit and finish. Different from

More information

Equilibrium. Conference Table. Installation Instruction. Revision B 11/07/16

Equilibrium. Conference Table. Installation Instruction. Revision B 11/07/16 Equilibrium Conference Table Installation Instruction Revision B 11/07/16 Equilibrium End User Agreement Enwork Equilibrium table bases must be installed directly onto a four inch minimum thickness concrete

More information

Assembly Instructions Above Worksurface Riser Shelf Systems and Back / End Stops

Assembly Instructions Above Worksurface Riser Shelf Systems and Back / End Stops Assembly Instructions Above Riser Shelf Systems and Back / End Stops Back Stops and End Stops Adjustable Riser Shelves Instrument Riser Shelves Stationary Riser Shelves IMPORTANT PLEASE READ THESE INSTRUCTIONS

More information

Revised

Revised Indentify Non-powered panels and separate from Powered panels. Non-powered panel shown at left.. Powered panel shown at left has powerway mounted at factory. Also separate panels by surface type, width

More information

INSTALLATION GUIDE 2009-CURRENT HUMMER H3T PRODUCT CODE:

INSTALLATION GUIDE 2009-CURRENT HUMMER H3T PRODUCT CODE: INSTALLATION GUIDE 2009-CURRENT HUMMER H3T PRODUCT CODE: 268 June 22, 2010 TOOLS NEEDED COMPONENTS INCLUDED P2 Tip 3/8" Drill Rubber Gasket(s) x 2 Bracket(s) x 2 1/2" Drill Bit Bulkhead Flange #2 Phillips

More information

INSTALLATION INSTRUCTIONS FOR INSTALLING T-SERIES EXTRA HEAVY DUTY LEVER LOCKSET

INSTALLATION INSTRUCTIONS FOR INSTALLING T-SERIES EXTRA HEAVY DUTY LEVER LOCKSET HIGH EDGE 2 1/4"(57mm) 03079400070 INSTALLATION INSTRUCTIONS FOR INSTALLING T-SERIES EXTRA HEAVY DUTY LEVER LOCKSET IMPORTANT: THIS LOCK IS NON-HANDED. LOCK IS FACTORY PACKED PREADJUSTED FOR 1³ ₄" (45mm)

More information

BABY WOLF LOOM. Assembly Instructions for Knocked-Down Looms

BABY WOLF LOOM. Assembly Instructions for Knocked-Down Looms BABY WOLF LOOM Assembly Instructions for Knocked-Down Looms BEFORE YOU BEGIN Please read through the directions before beginning to assemble your loom. Unpack the loom parts carefully. Do not throw away

More information

Installation and Assembly: In-wall Mount for 32" to 71" Flat Panel Screens

Installation and Assembly: In-wall Mount for 32 to 71 Flat Panel Screens Installation and Assembly: In-wall Mount for 32" to 71" Flat Panel Screens Model# IM760P, IM760P-S IM760PU, IM760PU-S Screen size range 32" to 71" (81 to 180 cm) 32" to 60" (81 to 152 cm) IM760P IM760P-S

More information

CleanBench Laboratory Tables

CleanBench Laboratory Tables CleanBench 63 Series High-Performance Lab Tables... 2 Accessories Faraday Cages...11 SpaceSaver Overhead Rack...21 Support Bars...27 Sliding Shelves...37 Perimeter Enclosure...37 Casters...38 63-600 Series

More information

Interra Installation Manual

Interra Installation Manual Interra Installation Manual Instructions to install the Friant Interra panel system Friant & Associates, LLC Table of Contents Getting Started Introduction... 3 General Tools, Staging & Safety... 4 Before

More information

Installation and Assembly: Flat Video Wall Mount For 40" to 65" Flat Panel Displays

Installation and Assembly: Flat Video Wall Mount For 40 to 65 Flat Panel Displays Installation and Assembly: Flat Video Wall Mount For 40" to 65" Flat Panel Displays Model: DS-VW665 Maximum Load Capacity: 125 lb (57 kg) 1 of 11 ISSUED: 03-22-12 SHEET #: 125-9288-4 06-25-13 NOTE: Read

More information

SAM. Model: STV-C65 LCD Mobile Visualized Stand Instruction Manual. Weight Capacity: 1251bs / 56.7kg Suits LCD Flat Panel Display: 42"-55" Page 20

SAM. Model: STV-C65 LCD Mobile Visualized Stand Instruction Manual. Weight Capacity: 1251bs / 56.7kg Suits LCD Flat Panel Display: 42-55 Page 20 SAM Model: STV-C65 LCD Mobile Visualized Stand Instruction Manual Weight Capacity: 1251bs / 56.7kg Suits LCD Flat Panel Display: 42"-55" 20 Step 6 LCD Mobile Lift Stand Model: STV-C65 Cable management

More information

ASSEMBLY AND ADJUSTMENT

ASSEMBLY AND ADJUSTMENT EPPA MONITOR ARM EPPA Rev A 10/17 Model EPPA-XXX ASSEMBLY AND ADJUSTMENT EPPA MONITOR ARM PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the assembly and adjustment procedures. Check

More information

Footprint Mobile Assembly Instructions

Footprint Mobile Assembly Instructions Footprint Mobile Assembly Instructions 1998754 Revision -1 Complete Series Master Packet If you have any questions concerning these instructions, please call Kimball Office Customer Service. 20 Kimball

More information

Topo Freestanding Applications - Private Office

Topo Freestanding Applications - Private Office 4 3 2 Topo Freestanding Applications - Private Office Combo Wrench If you have a problem, question, or request, call your local dealer, or Coalesse at 1.800.627.6770 Or visit our website: www.coalesse.com

More information

Preference Collection 5580 Treatment Console INSTALLATION GUIDE

Preference Collection 5580 Treatment Console INSTALLATION GUIDE Preference Collection 5580 Treatment Console INSTALLATION GUIDE 0 WARNING Failure to install the 5580 as described in this installation guide may cause the unit to collapse, resulting in serious injury

More information

Serial Number Location

Serial Number Location GL/GLX STRENGTH TRAINING SYSTEM OWNERS MANUAL Serial Number Location SERIAL 3 4 5 7 8 Record your Serial number and purchase date here: S/N DATE: DEALER: Model No. BCG-GL BODYCRAFT is a division of Recreation

More information

MPA-9000 Universal Ceiling Projector Mount Kit

MPA-9000 Universal Ceiling Projector Mount Kit I N S T R U C T I O N M A N U A L Universal Ceiling Projector Mount Kit The Universal Ceiling Projector Mount provides a unique, simplified method of ceiling mounting your inverted projector. This low

More information

STRINGING MACHINE OWNER'S MANUAL. Copyright 1998 GAMMA Sports - All Rights Reserved

STRINGING MACHINE OWNER'S MANUAL. Copyright 1998 GAMMA Sports - All Rights Reserved 6002 STRINGING MACHINE OWNER'S MANUAL Issue 3 - June 20, 1998 Copyright 1998 GAMMA Sports - All Rights Reserved 6002 OWNER'S MANUAL TABLE OF CONTENTS PAGE 1... WARRANTY PAGE 2... FEATURES PAGE 3... ASSEMBLY

More information

Star Trac Turbo Trainer Assembly & Setup

Star Trac Turbo Trainer Assembly & Setup Star Trac Turbo Trainer Use the following procedures to unpack and assemble your Turbo Trainer manufactured by Star Trac. UNPACKING AND PARTS LIST Position the shipping carton so the Heavy End logo is

More information

Preference Collection and Treatment Console INSTALLATION GUIDE

Preference Collection and Treatment Console INSTALLATION GUIDE Preference Collection 5580.69 and 5580.96 Treatment Console INSTALLATION GUIDE WARNING Failure to install the 5580 as described in this installation guide may cause the unit to collapse, resulting in serious

More information

M2 Assembly. M2 Sub-Assemblies mm Belt Sub-Assembly mm Belt Sub-Assembly Spider Sub-Assembly... 4

M2 Assembly. M2 Sub-Assemblies mm Belt Sub-Assembly mm Belt Sub-Assembly Spider Sub-Assembly... 4 M2 Assembly Table of Contents M2 Sub-Assemblies... 3 630mm Belt Sub-Assembly... 3 702mm Belt Sub-Assembly... 3 Spider Sub-Assembly... 4 Idler Bolt Sub-Assembly... 8 Y Motor Sub-Assembly... 9 X Motor Sub-Assembly...

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS SPORTSMAN WINCH MOUNT GRILLE GUARD APPLICATION: 2016-2018 Toyota Tacoma PART NUMBER: 40-93885, 45-93880, 46-23885 ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 1 WINCH TRAY 15MM SOCKET

More information

PORTA~TRACE. GAGNE, INC. 41 Commercial Dr. Johnson City, New York Phone: Fax: ASSEMBLY INSTRUCTIONS

PORTA~TRACE. GAGNE, INC. 41 Commercial Dr. Johnson City, New York Phone: Fax: ASSEMBLY INSTRUCTIONS PORTA~TRACE GAGNE, INC. 41 Commercial Dr. Johnson City, New York 13790 Phone: 1-607-729-3366 Fax: 1-607-729-7644 ASSEMBLY INSTRUCTIONS PORTA~TRACE MODEL 2436T LIGHT TABLE PORTA~TRACE MODEL 3648T LIGHT

More information

Select Lab Adjustable Height Workstation

Select Lab Adjustable Height Workstation Assembly Instructions Select Lab Adjustable Height Workstation Mobile version is shown. Also available without casters. Contents Important User Information.............................. 2 Safety Precautions....................................

More information

Workbench Instructions for Assembly

Workbench Instructions for Assembly Workbench Instructions for Assembly FlexWorks is a trademark of Lista International Corporation. Making Workspace Work is a trademark of Lista International Corporation. Document Number: MD002A3 Print

More information

ABM International, Inc.

ABM International, Inc. ABM International, Inc. Lightning Stitch required 1 1.0: Parts List head and motor assembly (Qty. 1) Reel stand (Qty. 1) Needle bar frame clamp (Qty. 1) Motor drive (Qty. 1) 2 Cable harness with bracket

More information

The Bowflex Revolution XP Home Gym Assembly Instructions. P/N: Rev ( /0 )

The Bowflex Revolution XP Home Gym Assembly Instructions. P/N: Rev ( /0 ) P/N: 001-7057 Rev ( /0 ) The Bowflex Revolution XP Home Gym Assembly Instructions 2 Table of Contents Before You Start... 2 Tools You Will Need / Hardware Contents... 3 Box Contents... 6 Assembling Your

More information

Installation Instructions

Installation Instructions Installation Instructions 000964 Revision F Installation Instructions for PIRIT Read this manual fully prior to starting installation. Call American eating Customer ervice with any questions. What you

More information

TABLE OF CONTENTS REQUIRED TOOLS

TABLE OF CONTENTS REQUIRED TOOLS TABLE OF CONTENTS SECTION SECTION TITLE PAGE NO. 1 2 3 4 5 Assembling Mounting Structure Installing Bicycle Supports Mounting Rack to Wall Adding Sections Customizing Rack Configuration REQUIRED TOOLS

More information

Arlink 7000 Workstation

Arlink 7000 Workstation Arlink 7000 Workstation Instructions for Assembly Basic Bench Assembly Undersurface Accessories Above Surface Accessories Making Workspace Work is a trademark of Lista International Corporation. Creation

More information

PULL-THRU USER S MANUAL

PULL-THRU USER S MANUAL PULL-THRU USER S MANUAL G14x Part # 310 120 177 G20 Part # 310 120 188 G20x Part # 310 120 186 G40x Part # 310 120 163 TABLE OF CONTENTS SECTION 1 PCB DESIGN AND MOUNTING SECTION 2 MOUNTING ADAPTER TO

More information

INSTALLATION INSTRUCTIONS Small Flat Panel Height-Adjustable, Extended Pitch Swing Arm Wall Mount Model KWE-110

INSTALLATION INSTRUCTIONS Small Flat Panel Height-Adjustable, Extended Pitch Swing Arm Wall Mount Model KWE-110 INSTALLATION INSTRUCTIONS Small Flat Panel Height-Adjustable, Extended Pitch Swing Arm Wall Mount Model KWE-110 The KWE dual swing arm wall mount is designed to provide a broad range of viewing for Small

More information

Stuff-Your-Stuff Platform Bed (Twin and Full)

Stuff-Your-Stuff Platform Bed (Twin and Full) Stuff-Your-Stuff Platform Bed (Twin and Full) Pre-Assembly: Please read all instructions before beginning assembly. Assembly by two people is a must. Save all packing materials until assembly is complete

More information

Single Sided Height Adjustable Benching

Single Sided Height Adjustable Benching Single Sided Height Adjustable Benching Bit Holder Power Drill Long # Square Drive Bit 5mm Hex Drive Bit T-30 Torx Drive Bit Hex Key -.5mm (Provided) SERIES 5 Hex Key - 3mm Socket Adaptor (or) If you have

More information

Modular Bi-File Lateral

Modular Bi-File Lateral Modular Bi-File Lateral Installation Instructions 920-563-6362 E-mail: ssc@spacesaver.com Internet: www.spacesaver.com Contents Hardware Identification..................................3 Pre-Installation........................................6

More information

CONTROLS KIT FOR ALL # & # HARLEY DAVIDSON SPORTSTER MODELS

CONTROLS KIT FOR ALL # & # HARLEY DAVIDSON SPORTSTER MODELS INSTALLATION INSTRUCTIONS TC BROS. CHOPPERS PART #0-0075 & #0-0076 (No Pegs) FORWARD CONTROLS KIT FOR ALL 00-0 HARLEY DAVIDSON SPORTSTER MODELS If downloading & printing these instructions online, be sure

More information

INSTALLATION INSTRUCTIONS Small Flat Panel FMA Pivot Arrays Models: FMA-220 and FMA-320

INSTALLATION INSTRUCTIONS Small Flat Panel FMA Pivot Arrays Models: FMA-220 and FMA-320 INSTALLATION INSTRUCTIONS Small Flat Panel FMA Pivot Arrays The FMA-220 and FMA-320 pivot array allow both horizontal and vertical display pitch adjustment. The pitch adjustment range is 30 (15 up / 15

More information

INSTALLATION INSTRUCTIONS GRILLE GUARD 09-ON DODGE RAM PART #

INSTALLATION INSTRUCTIONS GRILLE GUARD 09-ON DODGE RAM PART # INSTALLATION INSTRUCTIONS GRILLE GUARD 09-ON DODGE RAM PART # PARTS LIST: Qty Description Qty Description 1 Grille Guard 8 12-1.75mm x 35mm Hex Bolts 2 Brackets (for trucks without 22 12mm x 30.1mm OD

More information

INSTALLATION MANUAL. All Recessed Wall-Mount Modules Front-Loading, Rear-Loading, Parcel-Only, Collection Box, Trash/Recycling Bin

INSTALLATION MANUAL. All Recessed Wall-Mount Modules Front-Loading, Rear-Loading, Parcel-Only, Collection Box, Trash/Recycling Bin INSTALLATION MANUAL All Recessed Wall-Mount Modules Front-Loading, Rear-Loading, Parcel-Only, Collection Box, Trash/Recycling Bin TABLE OF CONTENTS GENERAL INFORMATION AND ADVISORIES 3 USPS INSTALLATION

More information

MANUAL e130. Wallstation

MANUAL e130. Wallstation MANUAL 07.29.13 e130 Wallstation The Enovate Medical e130 Wallstation was designed to set a new standard in quality. Enovate Medical s goal is to provide a wallstation that is ready for years of use,

More information

Arlink 8000 Workstation

Arlink 8000 Workstation Arlink 8000 Workstation Instructions for Assembly Introduction Basic Frame Assembly Worksurface Assembly Drawer and Power Beam Assembly Light Fixture and Shelves Worksurface Grounding Instructions Wrist

More information

Select Lab Fixed Height Workstation

Select Lab Fixed Height Workstation Assembly Instructions Select Lab Fixed Height Workstation Contents Important User Information.............................. 2 Safety Precautions.................................... 3 Required Tools........................................

More information

INSTALLATION INSTRUCTIONS Small Flat Panel Mounts Model: F-Series

INSTALLATION INSTRUCTIONS Small Flat Panel Mounts Model: F-Series INSTALLATION INSTRUCTIONS Small Flat Panel Mounts Model: F-Series This Instruction Manual covers most of the F-Series wall and desk mounts, as well as selected F-Series pole mounts. NOTE: Some F-Series

More information

** Do Not Contact the Store ** For Assistance, including missing or broken parts, Call Customer Service at:

** Do Not Contact the Store ** For Assistance, including missing or broken parts, Call Customer Service at: 3/01/2007 VISIT THE LITIME WEB SITE: WWW.LITIME.COM ** Do Not Contact the Store ** For Assistance, including missing or broken parts, Call Customer Service at: 1 (800) 225-3865 Double Shed Doors for Back

More information

PFW 6875 Installation Guide Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d Installation, Installatie gids

PFW 6875 Installation Guide Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d Installation, Installatie gids Maximum Flat Panel Weight: 160 lb. / 72.57 kg. Included Components Wall Mount (Qty 1) Extension Brackets (Qty 2) Bracket (Qty 1 Pair) 5/16 Flat Washers (Qty 4) Universal Spacers (Qty 8) M5 Allen Driver

More information

TechBench Installation Manual

TechBench Installation Manual Manual Table of Contents TechBench Overview....2 Bench Assembly Linear,36 (914,4mm) Wide 96 (2438,4mm) Wide 3,4,5,6,7 Bench Assembly Linear,24 (609,6mm) Wide 30 (762mm) Wide..8,9 Bench Assembly Corner

More information

OPERATOR'S MANUAL ROUTER MOUNTING KIT

OPERATOR'S MANUAL ROUTER MOUNTING KIT OPERATOR'S MANUAL MOUNTING KIT 4950301 (FOR USE WITH BT3000 AND BT3100 TABLE SAWS) Your new router mounting kit has been engineered and manufactured to Ryobi's high standard for dependability, ease of

More information

User Instructions Multiline Otter Scoreboard Caddy Assembly

User Instructions Multiline Otter Scoreboard Caddy Assembly List of parts: User Instructions Multiline Otter Scoreboard Caddy Assembly Single Caddy Double Caddy 1 1 Base assembly with attached wheels 2 4 1 1 2 4 4 8 10 20 12 Uprights (60 or 74 aluminum extrusion)

More information

OPERATIONAL MANUAL V1.0. Removing/Replacing Blades

OPERATIONAL MANUAL V1.0. Removing/Replacing Blades OPERATIONAL MANUAL V1.0 BLUEROCK WS-212 Wire Stripper Removing/Replacing Blades CAUTION!! IMPORTANT!! DANGER!! WARNING!! DISCONNECT MACHINE FROM POWER BEFORE PROCEEDING!! Estimated Completion Time: 90

More information

RBP-1215B-RX DODGE RAM QUAD CAB RX3

RBP-1215B-RX DODGE RAM QUAD CAB RX3 RBP-1215B-RX3 2002-2017 DODGE RAM 15-3500 QUAD CAB RX3 Passenger side RX-3 Side Step Drill Template Passenger side rear Modular Bracket (6) L Support Brackets Driver side rear Modular Bracket Driver side

More information

model tsa-sa48 Sliding Crosscut Table installation guide

model tsa-sa48 Sliding Crosscut Table installation guide model tsa-sa48 Sliding Crosscut Table installation guide A Note About Color Variations Among Anodized Aluminum Components Congratulations on the purchase of this SawStop Sliding Crosscut Table. We at SawStop

More information

Flat Panel Stand FPZ-655. for 32" to 55" Flat Panel Screens FEATURES. Reinforced universal adapter plate for a strong hold

Flat Panel Stand FPZ-655. for 32 to 55 Flat Panel Screens FEATURES. Reinforced universal adapter plate for a strong hold FPZ-655 Flat Panel Stand for 32" to 55" Flat Panel Screens For a viewing experience that really stands out, Peerless FPZ-655 Universal Flat Panel Stand for 32" 55" flat panel TVs provides a brilliant combination

More information

Midmark Care Exchange 6282 Standard Duty Wall Mounted Workstation

Midmark Care Exchange 6282 Standard Duty Wall Mounted Workstation INSTALLATION MANUAL Midmark Care Exchange 6282 Standard Duty Wall Mounted Workstation Weight Capacity 5-20 lbs 1210180MD Rev. C TABLE OF CONTENTS Tools Required / Installation Warnings / Disclaimer / Safety

More information

STAKS. Crossover Casegoods ASSEMBLY INSTRUCTIONS

STAKS. Crossover Casegoods ASSEMBLY INSTRUCTIONS STAKS Crossover Casegoods ASSEMBLY INSTRUCTIONS Installation Sequence 1. Wall Panels a. Connector Kit Part Identification 3 b. T - 3 Panel Connection Preparation 4 c. X Panel Connection Preparation 5 d.

More information

GlideRite Retractable Cover System For Hot Spot Spas (SE & SLX only)

GlideRite Retractable Cover System For Hot Spot Spas (SE & SLX only) List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.

More information

Replacing the Reciprocator on the SWF Compact Series Machine (601C and 1201C)

Replacing the Reciprocator on the SWF Compact Series Machine (601C and 1201C) Follow the instructions below to replace the reciprocator in the SWF Compact series machines. The tools required can be found in the tool kit that came with the machine. Preparation 1. First, place the

More information

MantelMount. TM1A Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS

MantelMount. TM1A Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS MantelMount TMA Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS TM Thank you for choosing the MantelMount television wall mount. Please read this entire manual before

More information

Side Mount INSTRUCTION BOOKLET #C122 BED STYLE: PARK CITY

Side Mount INSTRUCTION BOOKLET #C122 BED STYLE: PARK CITY Side Mount BED STYLE: PARK CITY INSTRUCTION BOOKLET #C1 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT

More information

Mirage Installation Manual

Mirage Installation Manual Mirage Installation Manual General Information This installation manual provides necessary information for the safe installation of the Mirage product. WARNING: Failure to follow the instructions in this

More information

Cable Tray Kit: - Cable Tray - Cable Tray Cover - Power Block Support (x2) Top Support Kit: (x2) - 2 Top Supports. Quantities are per bench

Cable Tray Kit: - Cable Tray - Cable Tray Cover - Power Block Support (x2) Top Support Kit: (x2) - 2 Top Supports. Quantities are per bench Parts Included (per back to back bench) Column Kit: (x2) - 1 LH & 1 RH Column - Control Box - Hand Switch Cable Tray Kit: - Cable Tray - Cable Tray Cover - Power Block Support (x2) Depth Support Kit: -

More information

MobileTrak5 Installation Instructions

MobileTrak5 Installation Instructions MobileTrak5 Installation Instructions PLEASE OPEN ALL BOXES & CHECK TO MAKE SURE YOU HAVE ALL PIECES REQUIRED READ ALL INSTRUCTIONS BEFORE STARTING Tools Required for Assembly 7/16, 1/2 Wrench Phillips

More information

S6 User s Manual USER S MANUAL ver. 1.0

S6 User s Manual USER S MANUAL ver. 1.0 S6 User s Manual SKEETER - 1U LOW PROFILE SOLUTION Table of Contents Tabletop Configuration 2 Tabletop Configuration Accessories 4 Slide Configuration 5 slide configuration accessories 7 rack Mount configuration

More information

P.O. Box 8400 Green Bay, WI (920)

P.O. Box 8400 Green Bay, WI (920) P.O. Box 8400 Green Bay, WI 54308-8400 (920) 468-2165 Change Notice No. 112 Implemented By: KI-Pembroke Notification By: Scott Vissers Date: 03/15/10 Component Product Title: Series XXI Lateral Filing

More information

GlideRite Retractable Cover System For HotSpring & Tiger River Spas (except Classic & pre-2000 Landmark Spas)

GlideRite Retractable Cover System For HotSpring & Tiger River Spas (except Classic & pre-2000 Landmark Spas) List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.

More information

IMPULSE G2/PULSE STATIC BRIDGE & RETURN MODULE. Drill. Desk Connecting. Outside by fastening the supplied wood screws from the HK-67 kit through the

IMPULSE G2/PULSE STATIC BRIDGE & RETURN MODULE. Drill. Desk Connecting. Outside by fastening the supplied wood screws from the HK-67 kit through the PART # 1608990 STATIC BRIDGE & RETURN MODULE 1. This sheet covers the steps to install a static bridge or return module with the FX no hinged access panel back option to a height adjustable freestanding

More information

TIRE RACK INSTALLATION INSTRUCTIONS Dodge Sprinter

TIRE RACK INSTALLATION INSTRUCTIONS Dodge Sprinter Aluminess Products Inc 9402 Wheatlands Ct. #A Santee, CA 92071 619-449-9930 TIRE RACK INSTALLATION INSTRUCTIONS 07-11 Dodge Sprinter Please read before beginning Stainless steel hardware may bind together

More information

OPERATOR'S MANUAL 46" SNOW BLADE. Model Numbers OEM IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY

OPERATOR'S MANUAL 46 SNOW BLADE. Model Numbers OEM IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY OPERATOR'S MANUAL 46" SNOW BLADE Model Numbers 190-833-OEM IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY MTD PRODUCTS INC. P.O. BOX 368022 CLEVELAND, OHIO 44136-9722 PRINTED IN U.S.A. FORM NO.

More information