Easy2Build TM. 8 x 8 Easy-Grow Greenhouse. Assembly Instructions. Smart Tech solutions

Size: px
Start display at page:

Download "Easy2Build TM. 8 x 8 Easy-Grow Greenhouse. Assembly Instructions. Smart Tech solutions"

Transcription

1 EasyBuild TM Smart Tech solutions 8 x 8 Easy-Grow Greenhouse Assembly Instructions 0 Structure 7 PC SHELL Systems Trading Corporation 50 7th Avenue Suite 809, New York, NY 03 Customer Service: (877) ext customerservice@stcaustin.com

2

3 Introduction Thank you for purchasing your EasyBuild TM 8x8 Easy-Grow Greenhouse. This model features two roof vents and a circular air vent to ensure proper ventilation. We have also included an automatic vent opener to help you maintain optimal temperature effortlessly. When properly assembled and maintained, this greenhouse will provide years of enjoyment. These instructions include helpful hints and important information needed to safely assemble and properly maintain the greenhouse. Please carefully read these instructions completely before you begin. This greenhouse has been designed with patented technology to be easily assembled. All but one step can be completed by one person. You will require assistance from another person to attach the roof. Although the greenhouse can be assembled in six to eight hours, we recommend that you take your time and make it a weekend project. Before Starting Assembly: CAREFULLY READ ALL INSTRUCTIONS BEFORE YOU BEGIN AND FOLLOW THE STEPS IN THE ORDER THEY ARE PRESENTED.. Make sure you have all the necessary parts: Compare the contents of the two cartons to the List of Parts. If any parts are missing or damaged or you have any questions, please contact Customer Service by phone at (877) ext. or by at customerservice@stcaustin.com before beginning assembly.. Lay the parts out in separate staging areas: The List of Parts has the corresponding step number referenced to each part. We recommend that while you go through the list, make staging areas for each step and place the parts necessary for each step in these areas. This will save you time and effort during assembly. 3. Select a Location: When selecting a site for your greenhouse, a flat level area is essential and if possible, with proper water drainage and easy access to power and water necessary for greenhouse gardening. Choose a sunny, level position away from overhanging trees and power lines and protected from the wind as much as possible. The location should be away from structures that could cause snow to drift on or around the greenhouse. Locate underground pipes or cables before preparing the site or anchoring the greenhouse. Note: You may assemble the greenhouse on a hard level surface and move it to its final position when finished. Make sure there are no obstacles between the assembly area and the final position.. Prepare a Foundation: After choosing a location, proper preparation of the site is essential. The site must be level. If the site is not level, create a base slightly larger than the outside dimensions of the greenhouse using a perimeter of two by fours filled with either soil, sod or gravel. Make sure the base is square by measuring the diagonals from both sides and making sure they are equal. The greenhouse is secured from the inside with pegs into holes cast with concrete. See step6 for details. If you decide to have a concrete base, it is best to contact a reliable contractor to ensure it is flat and level. Make sure you have checked with your local authorities regarding any required building permits. 5. Make sure you have the proper tools: Tape Measure Work Gloves Safety Goggles Phillips Screwdriver Spirit Level Small Step Ladder Wooden Mallet Liquid Soap or WD0 Lubricant Scissors Hex Key (included) NOTE: A cordless drill with Phillips head bit is highly recommended but not essential. of 55

4 Safety Advice The greenhouse must be positioned and fixed on a flat level surface. Dispose of all plastic bags safely. Keep them out of the reach of small children. Keep children and pets away from the assembly area until the work is completed. Always wear shoes, gloves and safety goggles when working. In manufacturing all sharp edges and burs have been removed but caution should still be taken when handling metal parts. Do not lean against or push the greenhouse during assembly. Take special care not to touch overhead power lines with the aluminium profiles. Do not attempt to assemble the greenhouse in windy or wet conditions. Do not position your greenhouse in an area exposed to excessive wind. If using power tools or a step ladder always follow the manufacturers safety instructions. Hot items such as recently used grills, blowtorches etc. must not be stored in the greenhouse. Store the polycarbonate panels in a cool dark place like a garage until you are ready to use them. Make sure the greenhouse complies with local building codes. Table of Contents Introduction... Safety Advice... General Order of Assembly... List of Parts... 3 Assemble Back... 6 Assemble Doors... 5 Assemble Front... 9 Assemble Sides... 7 Prepare Shelves... 3 Connect Sides to Back Connect Sides to Front Assemble and Connect Gables Brace Sides... Assemble and Install Roof Vents... Install Circular Vent... 8 Install Side and Roof Panels... 9 Install Weather Stripping Install Trim Plates... 5 Weather Strip and Hang Doors Secure to Ground... 5 Install Trays and Bin Holder General Order of Assembly Step : Assemble Back Step : Assemble Doors Step 3: Assemble Front Step : Assemble Sides Step 5: Prepare Shelves Step 6: Connect Sides to Back Step 7: Connect Sides to Front Step 8: Assemble and Connect Gables Step 9: Brace Sides Step 0: Assemble and Install Roof Vents Step : Install Circular Vent Step : Install Side and Roof Panels Step 3: Weather Stripping 6 Step : Install Trim Plates Step 5: Weather Strip and Hang Doors Step 6: Secure to Ground Step 7: Install Trays and Bin Holder of 55

5 List of Parts The greenhouse is shipped in two cartons. These cartons are heavy. Be careful when lifting them. Wear proper safety gear including work shoes, gloves and goggles. The parts are identified by removable stickers. Place all the parts for each step in staging areas, checking that you have all parts as you go. If any parts are missing or damaged, contact STC customer service before beginning assembly: Customer Service: (877) ext. or L0C L0I L0J L0K L0L Step Step Step Step 3 Step 3 L06A Step 3 L06J Step 3 L06K Step 3 L05D L0A L0B Steps,3 Steps,3 L0G L0I L0J L0K L0L Step 8 Step Step Step 3 Step 3 L03A L03B L03C L03D L03K L03L L03M L03N L030 L03P L03Q L05A L05C L05D L05F L05G L05H L05I Step Step Step Step Step Step Step 8 Step 8 Step 8 Step 8 Step 8 L0A Step 3 L0B Step L0C L0D L0G Step Step Step 7 L0F Step Step Step 3 Step 0 Step Step 0 Step Step L07A Step L07B Step L08A L08B Step 8 Step 8 L0A Step 0 LA Step 0 LB Step 0 L3B L3C L3D L3E L3G L3H L3F Step Step Step Step Step Step Step LA Step 5 LB Step 5 LC LD Step 5 Step 5 3 of 55

6 Panel Y Step S03 Step Y5 Step 3 Y6 Step 3 S0 Steps,3 Y9 Step S05 Steps,3 Y0 Step S09 Steps,3 Y6 Step Y7 Step S0 Steps,3 Y8 Step S Step Y9 Step 3 S8 Step 3 Y0 Step 3 Y Step S9 Step Y Step S Step 8 Y3 Step Y Step 0 S8 0 Steps,3 Y5 Step S39 Step Y6 Step of 55

7 Trim Plate rubber Shelf Trays Circular Vent circular vent vent frame L09A Step L09B Step J0L Step J0R Step J03 Step J06 Step stripping J0A 80M Steps 3,5 J05 0 Step 7 plastic nut Step Step Step Bracing Parts S06 S07 S6 hex key S3 Anchor Clip and Peg L5A S3 S35 S0 Steps,3,9 8 Step 9 Steps,3 Steps,3,9 3 Step Step Step 6 Step 6 Steps,3, Door Handle Door Lock Roof Vent Handle S9 S30 S3 S3 S33 S0 S0A Step Step Step Step Step Step Step S08 S08C S S7L 7 3 Steps, Step 3 Step Step 3 Auto Vent Opener S0 S3 S S SA S6 S S5 Step 0 S Step 0 SA Hair Pin Clip Steps,,3,,8 Steps,,0 Steps,,0 Step 0 Step 0 Step 0 Step 7 Step 0 Step 0 S7R S0 S S37 L6 Step 3 Step Step 8 Steps 5,7 3 Steps,3 5 of 55

8 Assemble Back Place all the parts for the back face on a level surface. Make sure the pieces are in the correct positions before assembling. Carefully follow the order of assembly to ensure an easy installation. Wear proper safety gear including work shoes, gloves and goggles. The back is assembled with the outside face to the ground. ALL VIEWS ARE SHOWN FROM INSIDE..A Slide short side of connector S0 into channels of profiles L0A and L0B. Line up last hole on connector S0 with hole in each profile. IMPORTANT: The holes are not at the midpoint of the profile. Arrange profile so the 8 portion will be the bottom when standing..b Secure with S0 screws. L0A L0B S0 8 (7 mm).a Line up bottom hole on short side of connectors S0 with hole on side of profiles L03C and L03D. S0 L03C L03D S0.B Secure with S0 screws. S0 8 (7 mm) NOTE: ALL VIEWS ARE FROM INSIDE. #L0A #L0B #L03C #L03D #S0 #S0 6 6 of 55

9 .3A Attach profiles L0B and L03C to profile L0F by sliding the long sides of connector S0 into channels lining up last hole in S0 with holes in profile L0F. Attach profiles L03D and L0A to profile L0F by sliding the long side of connector S0 into profile channels lining up last hole of S0 with holes in L0F. L0B L03C L03D L0F L0A L0F.3B Secure with four S0 screws. L03C L03D L0B L0F L0A L0F S0 NOTE: ALL VIEWS ARE FROM INSIDE. S0 Screw #L0F #S0 7 of 55

10 .A Slide connector L6 inside profiles L03L and L03K. The two end holes on each side of connector L6 line up with the two holes on each profile..b Secure with four S0 screws. L03L S0 L03L S0 L03K #L03K #L03L #L6 #S0 L6.5A Slide connectors S08 into channels of profiles L03C, L03D and L03K..5B Secure each connector with two S0 screws. L03K L03L S0 L0B L03C S08 L03D L03K L0A S08 S08 NOTE: ALL VIEWS ARE FROM INSIDE S08 #S0 #S of 55

11 .6A Slide connector L6 inside profiles L0I and L0J..6B Line up the outside holes on L6 with second hole on profiles L0I and L0J. Secure with two S0 screws. L0I L0I L6 L0J L0J NOTE: ALL VIEWS ARE FROM INSIDE #L0I #L0J #L6 #S0.6C Slide connectors S0 into profile L0I and connector S05 into profile L0J until they securely click into place. S0 s S0 and S05 CLICK into place. S05 L0I L0J S0 L0J L0I S05 There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves. #S0 #S05 9 of 55

12 .7A Carefully line up connector S0 with profile L0B and connector S05 with profile L0A. Slide profiles L0I and L0J half way into place. Continue sliding until connectors S0 and S05 click securely into profiles. NOTE: ALL VIEWS ARE FROM INSIDE. L03L.7B Line up holes on connectors S08 with holes in profiles L0I and L0J. Secure each connector with two S0 screws. L0B L03C S08 L03K L0I S0 S0 L03D L0I L0A s S0 and S05 CLICK into place. L0J S05 Screw There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves. #S0 6.8A Slide hex bolt S3 into channels of profiles L05A and L05H as shown..8b Screw hex nut S onto bolt. Do not completely tighten. L05A S L05H L05A L05H S3 #L05A #L05H Nut / Bolt #S3 #S of 55

13 .9A Remove protective plastic from both sides of panels Y, Y6, Y7 and Y8. Place side to face toward the sun facing down. Fit panels Y and Y6 into bottom channel of profiles L05A and L05H. L05A L05H L05H L05A Y Y6 Y6 Y Remove protective plastic from EACH side of poly carbonate panels before installing. Dispose of plastic properly. Install with side labeled Face this side towards the sun FACING DOWN..9B Slide panels and profiles L05A and L05H into V-channels on profiles L0A, L0B, L03C, L03D and L03L..9C NOTE: ALL VIEWS ARE FROM INSIDE. Slide panels Y7 and Y8 into V-channels on profiles L0A, L0B, L03C, L03D and L03L. Fit inside channels on profiles L05A and L05H. Y Y6 Y6 Y Y8 Y7 Y7 L03C L03L Y8 L0B L03D L05A L05H L05H L0A Y Y6 Y6 L05A Y Panel Panel #Y #Y7 #Y6 #Y8 of 55

14 .0 Slide hex nut S and hex bolts S3 into U-cutout in both sides of profiles L03C, L03D and L03K. Tighten securely to hold in place. L05A L05H L05H L03C L05A L03K L03D NOTE: ALL VIEWS ARE FROM INSIDE..A Slide profiles L0I and L0J into connectors S09, S0 and S until they click into place. s S09, S0 and S CLICK into place. S L0I S L0I L0J S09 L0J L0I L0J S0.5 (63 mm) S09.5 (63 mm) IMPORTANT: The holes are not at the midpoint of the profiles. Arrange profile so the.5 portion will be the bottom when standing. S0 There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves. #L0I #L0J #S09 #S0 #S of 55

15 .B Slide connectors S09 and S0 half way into profiles L0A and L0B. Continue sliding together making sure panels Y7 and Y8 fit into V-channels of profiles L0I and L0J. s click securely into profiles. S09 L0I Y8 Y7 Y7 L0J S09 L0B Y8 S0 L0A L0B s S09 and S0 CLICK into place. There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves. S0 L0A.A Place connectors S onto profiles L0I and L03C, L0J and L03L and L0J and L03D matching up all holes. L0I L0J L03C L03L S L03D.B Screw S0 screws partially into bottom two holes. Do not tighten. S0 S0.C Screw S0 screws into top two holes. Tighten all screws. Repeat for both sides. NOTE: ALL VIEWS ARE FROM INSIDE. S0 S0 #S0 #S 3 3 of 55

16 .3A Insert long side of cable connector S06 at an angle into profile channel L0B with HOOK FACING UP. Slide connector to other side of channel. Use hex key to securely tighten and hold in place. L0B Y L0F Y6 Y6 Y L0F L0A L0I.3B Attach one side of short cable S6 to hook on S06 and lace under profile L0F. Attach other side of cable to a second S06 cable connector and with hook facing center, insert into profile channel L0I. Push the S06 connector towards center until profile corners are square and cable is tight. Use hex key to securely tighten and hold in place. L0J L03C IMPORTANT: Make sure all corners are squared at 90 degrees. NOTE: ALL VIEWS ARE FROM INSIDE. L0I L0I. Repeat step.3 inserting cable connectors S06 into profiles L0A and L0J. Cable rests next to panel Y, under profile L0F. Slide connector until profile corners are square and cable is tight. Use hex key to securely tighten second connector and hold in place. L03D L0B Y L0F Y6 Y6 Y L0F L0A L0J L0I IMPORTANT: Make sure all corners are squared at 90 degrees. L0J Hex Key Cable Cable L0J #S06 #S6 of 55

17 Assemble Doors Place all the parts for both doors on a level surface. Make sure the pieces are in the correct positions before assembling. Carefully follow the order of assembly to ensure an easy installation. Wear proper safety gear including work shoes, gloves and goggles. Both doors are assembled with the outside face to the ground. ALL VIEWS ARE SHOWN FROM INSIDE..A Slide three hex bolts S3 into channel of profile L05I. L05I.B Screw two S hex nuts onto bolt on each end. Do not completely tighten. S S3 L05I. Remove protective plastic from both sides of panels Y5. Place side to face toward the sun facing down. Fit panels into channels of profile L05I. Remove protective plastic from EACH side of poly carbonate panels before installing. Dispose of plastic properly. Install with side labeled Face this side towards the sun FACING DOWN. L05I Y5 L05I.3 Place door profiles L3B, L3C and L3E next to connectors S8 around Y5 panels as shown. Slide connectors into profiles. Make sure panels and profile L05I fit into V-channels of each profile. S8 connectors will be secured to profiles in Step. Y5 L3E S8 L3B S8 Y5 S8 L3C Y5 S8 NOTE: ALL VIEWS ARE FROM INSIDE. S8 L3E Panel #Y5 #L05I Bolt / Nut #S3 #S 3 #L3B #L3C #L3E #S8 5 of 55

18 .A Slide hex nuts and bolts into U-cutout in side of profiles L3B and L3C. Tighten securely to hold in place..b Secure connectors with six S0 screws. NOTE: The holes at the top of profile L3B and the bottom left corner of profile L3E will be secured in Step.5. L3E L3B L3E L3B Y5 L3C Y5 Screw L3C L3E L3E #S0 6.5 Place brace L5A onto door lining up the holes on each end with the holes in profiles L3E and L3B. Slide hex bolt so it fits through hole in brace. Secure brace with two S0 screws and S hex nut. S0 L3E L3B S L3C L5A S0 L3E NOTE: The hole for hex bolt is not at the midpoint of brace. Turn brace until all holes line up. Brace will dip slightly when hex bolt is secured. NOTE: ALL VIEWS ARE FROM INSIDE. Brace #L5A Screw / Nut #S0 #S 6 of 55

19 .6A Open door handle kit and remove parts. Slide pin S9 through handle S30, washer S3and hole in profile L3C into washer S3. S30 S9 S3 L3C S3.6B Slide washer S3 into groove on pin S9 to hold securely in place. L3C S3.6C Hook one side of spring S33 into hole on handle S30. Hook the other side into pin hole on profile L3C. NOTE: s packaged as Door Handle Kit. #S3 S33 #S9 #S3 L3C #S30 #S33.7A Slide two hex bolts S3 into channel of profile L05F. L05F S3.7B Screw two S hex nuts onto bolt on each end. Do not completely tighten. S L05F.8A Remove protective plastic from both sides of panels Y6. Place side to face toward the sun facing down. Fit panels into channels of profile L05F. Y6 L05F Remove protective plastic from EACH side of poly carbonate panels before installing. Dispose of plastic properly. Install with side labeled Face this side towards the sun FACING DOWN. Y6 Panel Bolt / Nut #Y6 #L05F #S3 #S 7 of 55

20 .8B Place door profiles L3D, L3F, L3G and L3H next to connectors S8 around Y6 panels as shown. Slide connectors into profiles. Make sure panels and profile L05F fit into V-channels of each profile. S8 S8 L3G L3F S8 Y6 L05F L3H Y6 S8.8C Secure connectors with eight S0 screws. L3G S8 L3D S0 L3F.8D L3H Slide hex nuts and bolts into U-cutout in side of profiles L3F and L3H. Tighten securely to hold in place. L3D NOTE: ALL VIEWS ARE FROM INSIDE..9A L3G Place S0 locks on profiles L3D and L3G as shown. Center the levers so the screw holes are visible. S0 L3F.9B Secure each S0 lock with two S0A screws. S0A S0A L3G L3D L3H S0 S0 L3G L3D IMPORTANT: Install door locks so levers face the panels. S0 L3D.9C Move lever to the right side to place lock in the unlocked position. L3G L3D NOTE: Door locks are shown in the UNLOCKED positition. When door is installed in step 5 and door is closed, move lever to the left side to lock door. #L3F #L3D #L3G #L3H Lock #S0 #S0A Screw #S0 8 #S8 8 of 55

21 Assemble Front Place all the parts for the front face on a level surface. Make sure the pieces are in the correct positions before assembling. Carefully follow the order of assembly to ensure an easy installation. Wear proper safety gear including work shoes, gloves and goggles. The front is assembled with the outside face to the ground. ALL VIEWS ARE SHOWN FROM INSIDE. 3.A Lay out profiles L0A, L0B, L06A and L06B so all holes line up. Slide short side of connector S0 into channels of profiles L0A, L0B, L06A and L06K. IMPORTANT: The holes are not at the midpoint of the profile. Arrange profile so the 8 portion will be the bottom when standing. L06K L06A S0 S0 L0A L0B L0A S0 L06A S0 8 (7 mm) 8 (7 mm) L0B L06K 3.B Line up lower hole on connector S0 with hole in each profile and secure with S0 screws. NOTE: ALL VIEWS ARE FROM INSIDE. L06K L06A L0A L0B S0 #L0A #L0B #L06A #L06K #S0 #S0 9 of 55

22 3.A S8 Slide profiles L06J into L06A and L06K using connectors S8. S8 connectors do not snap into place. L06J S8 S8 L06K L06A 3.B Place connectors S7L and S7R on corners matching up bottom two holes with holes in profiles L06A, L06J and L06K as shown. S7L S7R S7L L06K L06J S7R L06A 3.C Secure each connector with S0 screws. L06K L06A S7L S7R S0 S0 #L06J #S8 #S7L #S7R 3.3A Attach profiles L0B and L06K to profile L0A. Slide long sides of connectors S0 into channels of profile L0A, lining up last hole in S0 with holes in profile L0A. Attach profiles L06A and L0A to profile L0A. Slides long side of connectors S0 into channels of profiles L0A, lining up last hole of S0 with holes in L0A. 3.3B Secure with S0 screws. L0B L06K L0B L06K L06A L0A L06A L0A L0A L0A S0 L0A L0A S0 NOTE: ALL VIEWS ARE FROM INSIDE. #L0A Screw #S0 0 of 55

23 3.A Slide profiles L0K and L0L into connectors S09, S8 and S0 until they click into place. s S09, S0 and S8 CLICK into place. S8 L0K S8 L0K L0L S09 L0K L0L L0L S0 6.5 (676 mm) 6.5 (676 mm) S09 IMPORTANT: The holes are not at the midpoint of the profiles. Arrange profile so the 6.5 portion will be the bottom when standing. There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves. S0 #L0K #L0L #S09 #S0 #S8 3.B Remove protective plastic from both sides of panel Y0. Place side to face toward the sun facing down. Fit panel into V-channel on profile L06. Y0 Remove protective plastic from EACH side of poly carbonate panels before installing. Dispose of plastic properly. Install with side labeled Face this side towards the sun FACING DOWN. L06J Y0 L06J NOTE: ALL VIEWS ARE FROM INSIDE. Panel #Y0 of 55

24 3.5A Slide connectors S09 and S0 half way into profiles L0A and L0B. Continue sliding together making sure panel Y0 fits into V-channels of profiles L0L and L0K. s S7L and S7R rest in channels of L0L and L0K. L0K s S09 and S0 click securely into L0L profiles. Y0 S09 S7L S7R S09 L0B S0 S0 L0B L0A L0A s S09 and S0 CLICK into place. There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves. 3.5B Loosen the four screws in connectors S7L and S7R enough to adjust door frame profiles L06A, L06J and L06K and align with gable profiles L0L and L0K. Secure connectors S7L and S7R to profiles L0K and L0L with two S0 screws and L0K tighten four screws connecting profiles L0L L06A andl06k. S7L L06J S0 L0K L0L L06K S7R L06A S7L S0 S7R Screw NOTE: ALL VIEWS ARE FROM INSIDE. #S0 of 55

25 3.6A Remove protective plastic from both sides of panels Y5, Y6 and Y9. Place side to face toward the sun facing the down. Fit panels Y9 into top channels of L05C. Y9 IMPORTANT: Make sure to assemble a right and left side. L05C Y9 Y9 L05C L05C Remove protective plastic from EACH side of poly carbonate panels before installing. Dispose of plastic properly. Install with side labeled Face this side towards the sun FACING DOWN. NOTE: ALL VIEWS ARE FROM INSIDE. Y0 3.6B Slide Y9 panels into V-channels on profiles L0A, L0B, L06A and L06K. Note Y0 panel sits next to panel Y9. L06K L06A Y0 L0B L0A Y9 Y9 Y9 3.6C Slide Y5 and Y6 panels into V-channels on profiles L0A, L0B, L06A and L06B. Fit inside channels on L05C profiles. Y0 L05C L05C Y9 L05C Y9 L05C L0B L06K L06A L0A Y6 Y5 Panel Panel Panel #L05C #Y6 #Y5 #Y9 3 of 55

26 3.7A Line up connector S08C with holes on profiles L0K as shown. L0K 3.7B L0K Secure with two S0 screws. 3.7C Slide connector L6 inside profiles L0K and L0L. L0K S08C 3.7D Line up outside holes on connector L6 with holes on profiles L0L and L0K. Secure with four S0 screws. L0K S0 L6 S0 S0 3.8A L0L Slide short side of connectors S0 into channels of profiles L0K and L0L. Line up last hole on connector with holes on profile. L0L S0 3.8B Secure with two S0 screws. S0 L0K L0K S0 L0L NOTE: ALL VIEWS ARE FROM INSIDE. S0 L0L #L0K #L0L #S0 #S08C #S0 #L6 #S0 #S0 3.8C Slide connectors S0 into profile L0K and connector S05 into profile L0L until they securely click into place. S05 S0 L0K L0L S0 L0K L0L S05 s S0 and S05 CLICK into place. #S0 #S05 of 55

27 3.9A As you slide bottom profiles L0L and L0K half way into place, carefully line up S0 connectors with channels on profiles L06K and L06A and S0 and S05 connectors with profiles L0B and L0A. Continue sliding, making sure panels Y6 and Y5 fit into V-channels. Snap connectors S0 and S05 securely into profiles. L06A S0 Y6 Y5 S05 L0L L0B L06K L06A s S0 and S05 CLICK into place. L0A L06A S0 S0 S0 L0K L0L S05 L0L There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves. S05 3.9B Secure S0 connector to profiles L06A and L06K with S0 screws. L06A S0 NOTE: ALL VIEWS ARE FROM INSIDE. L0L Screw #S0 5 of 55

28 3.0A Insert long side of cable connector S06 at an angle into profile channel L0B with HOOK FACING UP. Slide connector to other side of channel. Use hex key to securely tighten and hold in place. Y5 L0A L06A Y6 L06K L0B L0L L0K 3.0B Attach one side of short cable S6 to hook on S06 and lace under profile L0A. Attach other side of cable to a second S06 cable connector and with hook facing center, insert into profile channel L0K. Push the S06 connector towards center until profile corners are square and cable is tight. Use hex key to securely tighten and hold in place. IMPORTANT: Make sure all corners L06K are squared at 90 degrees. L0K L0K 3. Repeat step 3.0 inserting cable connectors S06 into profiles L0A and L0L. Cable rests next to panel Y5, under profile L0A. Slide connector until profile corners are square and cable is tight. Use hex key to securely tighten second connector and hold in place. Y6 L06K L06A Y5 L0A L0A L0B L0A L06A L0L L0L L0K IMPORTANT: Make sure all corners are squared at 90 degrees. NOTE: ALL VIEWS ARE FROM INSIDE. L0L Hex Key Cable #S06 Cable #S6 6 of 55

29 Assemble Sides Place all the parts for the sides on a level surface. Make sure the pieces are in the correct positions before assembling. Carefully follow the order of assembly to ensure an easy installation. Wear proper safety gear including work shoes, gloves and goggles. You are assembling both sides in the following steps. Both sides are identical until step 6..A S0 Line up the four profiles L03B so the holes are at the same position. Slide long side of connectors S0 and S08 into channel of profile, lining up holes as shown. Repeat for all four L03B profiles. S0 L03B.B Secure with three S0 screws. S0 S0 L03B S08 S08 #L03B #S0 #S0 #S0 #S08 8.A Place L03B onto profiles L07A and L0C. Line up holes as shown. L07A.B Secure with three S0 screws. Repeat to make two sets. L07A L07A L03B L03B S0 L0C S0 L0C Screw L0C #L0C #L07A #S0 6 7 of 55

30 .3A Place L03B onto profiles L07B and L0C. Line up holes as shown. L07B.3B Secure with three S0 screws. Repeat to make two sets. L07B L07B S0 L03B L03B S0 S0 L0C L0C S0 L0C Screw #L0C #L07B #S0 6.A Lay out profiles L03A so the holes are at the same position. Slide short side of connectors S0 into channel of profile until the last hole in S0 lines up with the bottom hole on profile L03A. L03A S0 IMPORTANT: The holes are not at the midpoint of the profile. Arrange profile so the 8 portion will be the bottom when standing..b Slide another connector S0 so it lines up with the middle hole on profile L03A. S0.C Secure all pieces with S0 screws. Repeat to make two sets. L03A L03A L03A S0 S0 8 (75 mm) 6 3/ (70 mm) #L03A #S0 #S0 8 of 55

31 .5A Lay out profiles L0D so the holes are at the same position. Slide short side of connector S0 into channel of profile, lining the last hole in S0 with the hole on profile L0D. Secure with S0 screw. S0.5B Slide connector S39 into profile L0D until it snaps into place. Repeat to make two sets. S39 L0D S39 CLICKS into place. L0D S39 There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves. S0 #L0D #S0 #S0 #S39.6 Slide connector S03 into profile L0B until it clicks into place. S03 S03 S03 CLICKS into place. L0B #L0B #S03.7A Attach profiles L0B and L0C to profile L03A by sliding the long sides of connectors S0 into the channels. The last hole of connector S0 lines up with the holes in the profiles. L03A.7B Secure with two S0 screws. Repeat to make two sets. IMPORTANT: S03 rests on top of connector S0. S0 screw secures S03 to profile L0B. L0B S0 L0B L0C S0 S03 L03A S0 S0 L0C #L0C Screw #S0 9 of 55

32 .8A Connect profile L0D by sliding connector S39 into profile L0B until it snaps in place. Slide connector S0 into channel of L0C..8B Secure with S0 screw. Repeat to s S39 CLICKS into place. make two sets. S39 L03A L0B S39 L0C Screw L0D S0 #S0 S0 There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves..9 Slide connectors S9 and S03 into profile L03A. Snap securely into place. Repeat to make two sets. S9 s S03 and S9 CLICK into place. S9 L03A S03 S03 #S03 #S9 30 of 55

33 .0 Slide sections together as shown. Repeat to make two sets. There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves. s S03 and S9 CLICK into place. L07A S9 L07B L07B S9 L07A L03A L0C S03 L0C NOTE: ALL VIEWS ARE FROM INSIDE. L0C S03 L0C NOTE: The two sides are identical. When you connect them to the back, there will be a right and left side. Stand these up. 3 of 55

34 Prepare Shelves Place all the parts for the shelves on a level surface. Make sure the pieces are in the correct positions before assembling. Carefully follow the order of assembly to ensure an easy installation. Wear proper safety gear including work shoes, gloves and goggles. 5.A Line up the shelf profiles so the holes are at the same position. Slide long side of connector S37 into channel of each profile, lining up the last hole on the connector with the hole in the channel. LB S37 LC LD S37 LA IMPORTANT: The shelf profiles have rectangular holes in the channel or side of one end. Slide connector S37 into other side, lining up last hole in connector with hole in the channel. 5.B Secure with S0 screw. S37 S0 #LA #LB #LC #LD #S37 #S of 55

35 Connect Sides to Back With the outside facing a wall, carefully stand back up and lean against the wall. Stand each side up and place next to the back. Both sides are identical until the shelf profiles are connected. Make certain that positions of profiles L07A and L07B match the diagrams before connecting. 6.A Set up one side facing inside with L07B next to the back. Slide shelf profile LB into connector S03 until it clicks into place. Slide shelf profile LD into connector S39 until it clicks into place. L07B s S03 and S39 CLICK into place. L07A LB LB LD S03 LD S03 S39 S39 6.B Carefully slide left side into back, lining up connectors with profiles. Move side so connectors S09 and S0 are half way into profiles L07B and L0C. s S37 rest on top of profile L0F. Push side in until connectors click into place. S37 S37 L0F L07B S09 L07B S09 L0F Secure connectors S37 to profile L0F with two S0 screws. S0 S37 S0 LB S37 L0F LD S0 L0C L0C S0 VIEWS FROM INSIDE. s S0 and S09 CLICK into place. There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves. Screw #S0 33 of 55

36 6.A Set up the other side facing inside with profile L07A next to back. Slide shelf profile LA into connector S03 until it clicks into place. Slide shelf profile LC into connector S39 until it clicks into place. L07A s S03 and S39 CLICK into place. LA LA LC S03 LC S03 S39 S39 There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves. 6.B Carefully slide right side into back, lining connectors up with profiles. Move side so connectors S0 and S05 are half way into profiles L07A and L0C. s S37 rest on top of profile L0F. Push side in until connectors click into place. S0 CLICKS into place. S0 L07A S0 L07A L0F S37 L0F S37 LC LA Secure connectors S37 to profile L0F with S0 screws. S05 S0 L0C S0 L0F S05 VIEWS FROM INSIDE. L0C S05 CLICKS into place. Screw #S0 3 of 55

37 Connect Sides to Front Keep the structure as is, with the back against the wall until you finish this step. This will make it easier to keep the angles square. 7. Slide shelf profile LA into connector S03 on the left side until it clicks into place. Slide shelf profile LB into connector S03 on the right side until it clicks into place. LA S03 s S03 CLICK into place. L07A LA S03 L07B S03 LB S03 LB s S03 CLICK into place. There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves. 35 of 55

38 7.A Lift front from inside and rest it next to sides. Line up connector S0 with profile L07A, connector S09 with profile L07B and connectors S0 and S05 with profiles L0C. S0 L07A S09 LA L07B S05 LB S0 L0C 7.B Carefully pull the front until all connectors are half way inside each profile. Make sure connector S37 attached to shelf profiles rest on top of profile L0A. Push front into sides until connectors click into place. S09 s S09 and S0 CLICK into place. S37 L07B S0 L07A S37 L0A S09 L07B LA S37 S05 S0 LB L0C S0 L0C s S0 and S05 CLICK into place. There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves. 36 of 55

39 7.3A Slide shelf profile LC at a slight angle so one end slides half way into connector S39 and the other side with connector S37 rests on top of profile L0A. Continue to slide until profile clicks into connector S39. S39 CLICKS into place. LC S39 There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves. 7.3B Repeat step 7.3A, sliding shelf profile LD into S39 connector. Make sure connector S37 rests on top of profile L0A. S39 CLICKS into place. L07A LD S39 S37 L0A LA LC S39 7.3C Secure S37 connectors to L0A profiles with four S0 screws. L0A LD L0A LA LB LC Screw VIEWS FROM INSIDE. #S0 37 of 55

40 Assemble and Connect Gables Place all the parts for the gables on a level surface. Make sure the pieces are in the correct positions before assembling. Please carefully follow the order of assembly to ensure an easy installation. Wear proper safety gear including shoes, gloves and goggles. 8.A Slide connector S into channels of profiles L03M. Slide another S connector into channels of profiles L03O and L03P. IMPORTANT: U-shaped cutout is not at midpoint of profiles S L03O and L03P. Attach longer side (3.5 ) to connector S. L03M L03M S 8.B Secure each set with four S0 screws. L03M L03M S L03O L03P L03O L03P S0 #L03M #L03O #L03P 8.A Slide connector S into profiles L03Q and L03N until it clicks securely into place. IMPORTANT: U-shaped cutout is not at midpoint of profiles L03N and L03Q. Attach longer side (3.5 ) to connector S. Make sure coonector S is positioned correctly before connecting. #S0 #S 8 s S CLICKS into place. S S 8.B Line up holes on bracing bar S3 with holes in profiles L03Q and L03N. S3 L03N L03Q L03N L03Q 8.C Secure brace to profiles with two S0 screws. L03Q L03N L03Q L03N There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves. S0 #L03N #L03Q #S Screw #S0 Brace #S3 38 of 55

41 8.3 From the inside of the greenhouse, use two people to carefully lower center gable onto frame. Line up and slide profiles L03N and L03Q into connectors S9 until they click securely into place. L03N L03N L03Q S9 S9 S9 s S9 CLICK into place. L03Q S9 L03N L03Q There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves. NOTE: U-shaped cutouts on profiles L03N and L03Q face the back. 8. From the inside of the greenhouse, use two people to carefully lower front and back gables onto frame. Line up and slide connectors S0 into channels of profiles L03M, L03O and L03P. L03O L03M L03M L03O L03P NOTE: U-shaped cutouts on profiles L03O and L03P face the front. S0 S0 L03O S0 S0 S0 L03P L03P S0 39 of 55

42 8.5A Line up profiles L08A and L0G as shown. L08A has a cutout on one end. The plain side slides into V-channel of profile L0G. Note the rectangular holes in the channels of profile L0G are NOT on the side next to the V-channel. 8.5B Slide the plain side of L08B into V-channel on L08A opposite side of profile L0G. L08B L08A L0G L08B L08A L0G L0G L0G L08B L08A 8.6A IMPORTANT: There is one correct way to connect these profiles. Arrange profiles before sliding together. Use WD0 or liquid soap if parts do not easily slde together Using a small step ladder inside the greenhouse, carefully slide profile L0G with L08A and L08B connected into back connector S at a slight angle. Gently push center gable slightly towards the front to slide other end of profile into connector S. Make sure both connectors snap securely into place. Note L0G profile rests on top of connector S. IMPORTANT: Make sure profiles L0G with L08B are in correct positions before installing. Arrange profile L0G so rectangular holes in channels face the LEFT when looking at the front of the greenhouse from the outside. #L0G #L08A #L08B S L0G S L08B S s S and S CLICK into place. 8.6B Slide profile L0G at a slight angle into center gable connector S. Gently push front side slightly forward to slide other end of profile into connecor S8. Make sure both connectors click securely into place. Note profile L0G rests on top of connector S. IMPORTANT: Arrange profile L0G so rectangular holes in channels face the LEFT when looking at the front of the greenhouse from the outside. S L0G S S8 s S and S8 CLICK into place. There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves. #L0G 0 of 55

43 8.7A From inside of greenhouse secure S0 connectors to profiles L03M, L03O and L03P with two S0 screws. 8.7B Secure S connectors to profiles L0G with one S0 screw. L03O L0G S0 S0 S L03P S0 S0 S0 VIEWS FROM INSIDE. Screw VIEWS FROM INSIDE. #S A From inside of greenhouse, line up bracing bar S3 with holes in profiles L03A and L03N. Secure one S0 screw partially into each end. Then go back and tighten both screws. L03N L03N S0 8.8B Line up bracing bar S3 withholes in profiles L03A and L03Q. Secure one S0 screw partially into each end. Tighten both screws. L03Q S3 S3 S0 L03A S3 L03Q L03A S0 VIEWS FROM INSIDE. L03A S3 S0 L03A VIEWS FROM INSIDE. Screw Brace #S0 #S3 of 55

44 Brace Sides Place all the parts for bracing the sides on a level surface. Make sure the pieces are in the correct positions before assembling. Please carefully follow the order of assembly to ensure an easy installation. Wear proper safety gear including shoes, gloves and goggles. 9.A From the inside of the greenhouse, insert long side of cable connector S06 into profile channel L07B with hook facing the front. Slide connector to other side of channel. Use hex key to securely tighten and hold in place. L07B L0B L07B LA L03A L0B IMPORTANT: Make sure all corners are squared at 90 degrees. L0C 9.B Attach one side of long cable S07 to hook and lace behind profile LA. Attach other side of cable to a second S06 cable connector. With hook facing the back, insert connector into profile channel L0C. L03A 9.C Push towards center until profile corners are square and cable is tight. Use hex key to securely tighten and hold in place. L03A L0C IMPORTANT: Make sure all corners are squared at 90 degrees. VIEWS FROM INSIDE. L0C 9. Repeat step 9. inserting cable connectors S06 into profile L07B with hook facing the back and into profile L0C with hook facing the front. Cable rests behind profile LA. Slide connector until profile corners are square and cable is tight. Use hex key to securely tighten second connector and hold in place. L07B VIEWS FROM INSIDE. L0B L03A L0C L07B LA L03A IMPORTANT: Make sure all corners are squared at 90 degrees. L0B L0C Hex Key Cable #S06 Cable #S07 of 55

45 9.3A From the inside of the greenhouse, insert long side of cable connector S06 into channel of profile L07A with hook facing the back. Slide connector to other side of channel. Use hex key to securely tighten and hold in place. L07A L07A LB L0A L0A L03A L0C 9.3B L03A Attach one side of long cable S07 to hook and lace behind profile LB. Attach other side of cable to a second S06 cable connector. With hook facing the front, insert connector into channel of profile L0C. 9.3C Push towards center until profile corners are square and cable is tight. Use hex key to securely tighten and hold in place. L0C L03A IMPORTANT: Make sure all corners are squared at 90 degrees. VIEWS FROM INSIDE. L0C 9. Repeat step 9.3 inserting cable connectors S06 into profile L07A with hook facing the front and into profile L0C with hook facing the back. Cable rests behind profile LA. Slide connector until profile corners are square and cable is tight. Use hex key to securely tighten second connector to hold in place. L07A L0A 9.5 L03A VIEWS FROM INSIDE. L0C Repeat step 9. through 9. on the other side of the greenhouse. L03A L07A LB L0A L0C L0B LB L07B L07A IMPORTANT: Make sure all corners are squared at 90 degrees. L0C LA L0A Hex Key Cable Cable L0C #S06 #S of 55

46 Assemble and Install Roof Vents Place all the parts for both roof vents and handles on a level surface. Make sure the pieces are in the correct positions before assembling. Carefully follow the order of assembly to ensure an easy installation. Wear proper safety gear including work shoes, gloves and goggles. The roof vents are assembled with the outside face to the ground. ALL VIEWS ARE SHOWN FROM INSIDE. Assemble BOTH vents first and then add the handles. IMPORTANT: This greenhouse is equipped with one MANUAL vent handle (S5 installed in step0.3) and one AUTOMATIC vent handle (auto vent opener installed in step 0.0). The auto vent opener is packed separately. 0. LA Remove protective plastic from both sides of panels Y. Place side to face toward the sun facing down. Fit panels into channels of profiles L0A and LA. LA Y Remove protective plastic from EACH side of poly carbonate panels before installing. Dispose of plastic properly. Install with side labeled Face this side towards the sun FACING DOWN. L0A L0A 0.A LA LB Fit panel and profiles L0A and LA into channels of profiles LB. Make sure holes in ends of profiles line up. 0.B Secure with four S6 S6 screws. LA Y LB S6 LA Y LB S6 LB L0A LB L0A S6 LA LB NOTE: ALL VIEWS ARE FROM INSIDE. LB S6 LB L0A S6 L0A Screw Panel #S6 8 #LB #L0A #LA #Y 0.3 Attach handle S5 to profile L0A with two S screws. NOTE: You will install the handle to the second vent in step 0.0. S5 S5 IMPORTANT: hollow side of handle S5 faces down when attached. S S Y S S L0A L0A Handle #S5 Screw #S of 55

47 0.A Unpack contents of Auto Vent Opener. Slide cylinder and piston rod through set collar on arm A. set collar arm A piston rod cylinder 0.B Continue sliding cylinder so piston rod fits into push arm and arm B begins to open. Align hole in piston rod with second hole in push arm. Insert hair pin clip to secure. hair pin clip 0.C arm B Slide cylinder so threaded area enters set collar. Turn cylinder clockwise to screw cylinder into set collar. As you continue turning, the piston rod forces the push arm back, pushing arm A and arm B together. arm A push arm cylinder Handle push arm NOTE: The Auto Vent Opener will be installed to the vent in step 0.0 Cylinder with Piston cylinder push arm Hair Pin Clip 0.5A Slide two S3 hex bolts into channel of profile L05D and four S3 hex bolts into channel of profile L05G. 0.5B Screw two S hex nuts onto bolts on ends of each profile. Do not completely tighten. S L05D L05D L05G L05G S3 Bolt / Nut #L05D #L05G #S3 6 #S 0.6A With pins facing up on the inside of the greenhouse, slide one end of profile L05D into V-channel of profile L03P. Angle it slightly to fit the other end into V-channel of profile L03Q. L03O L05D L03P L03N L03P IMPORTANT: Make sure the pins face UP on INSIDE of the greenhouse when profile L05D is installed. L03Q L03P L05D L03Q VIEW FROM INSIDE. 0.6B Line up L05D channel with U-shaped cutouts in sides of profiles L03P and L03Q. Slide hex nut and bolts into U-shaped notches and tighten securely. L05D L03Q L05D L03Q VIEWS FROM INSIDE. 5 of 55

48 0.7 Repeat step 0.6 to install profile L05G on the other side of the greenhouse. With the nuts and bolts are facing the inside, secure profile L05G to profiles L03N and L03O. L03N L03N L05G L03O L05G VIEW FROM OUTSIDE. L05G L03O L05G L03O VIEWS FROM INSIDE. 0.8A Stand on a small step ladder inside the greenhouse. Install roof vent with handle S5 to the right side of greenhouse. Slide profile LA into profile L08A from the back of the greenhouse towards the front. IMPORTANT: The handle of roof vent is on the inside of the greenhouse. L08A LA Y L08A LA L05D 0.8B Continue to slide vent past the end of profile L08A until the hole in the other end is visible. Screw SA into hole in L08A and slide vent back until it rests next to the screw. L08A L08A YSA SA L05D Screw #SA 6 of 55

49 0.9A Stand on a small step ladder inside the greenhouse. Install second roof vent to the left side of the greenhouse. Slide profile LA into profile L08B from the back of the greenhouse towards the front. Y L05G LA L08B 0.9B Continue to slide vent past the end of profile L08B until the hole in the other end is visible. Screw SA into hole in L08A and slide vent back until it rests next to the screw. L08B SA Screw #SA 0.0A From the inside of the greenhouse open arms of auto vent slightly. Line up window bracket on arm B to holes in vent profile L0A and attach with two SA screws. arm B SA L0A L0A 0.0B Slide bolts in channel of profile L05G until they fit into holes on end of arm A. Secure with two S hex nuts. NOTE: ALL VIEWS ARE FROM INSIDE. arm A S Nut / Screw L05G L05G #S #SA 0.0C Carefully push upper handle B down until vent closes completely. Turn cylinder clockwise until threaded area of cylinder is centered to set collar as shown. L05G set collar IMPORTANT: Tighten the cylinder when you finish or the auto vent will not function. L0A cylinder cylinder 7 of 55

50 Install Circular Vent.A Place all the parts for circular vent on a level surface. Make sure the pieces are in the correct positions before assembling. Carefully follow the order of assembly to ensure an easy installation. Wear proper safety gear including work shoes, gloves and goggles. Open box containing the parts for circular vent. From the outside of the greenhouse, line up vent frame pins with holes in panel Y6, and slide into place. From the inside of the greenhouse, slide circular vent under the cable. Line up pins in vent frame with holes in circular vent and slide into place. IMPORTANT: Circular vent rests under the bracing cable. See step 3.0 for detailed instructions on adjusting the cables. Y6.B From the inside, secure the vent with four plastic nuts. Y6.C Double check that the profile corners are squared at 90 degrees and adjust if necessary. See step 3.0 for detailed instructions. Y6 NOTE: VIEWS ARE FROM INSIDE. IMPORTANT: Make sure all corners are squared at 90 degrees. Vent Frame Circular Vent Plastic Nuts 8 of 55

51 Install Side and Roof Panels Place all side and roof panels on a level surface. Make sure the pieces are in the correct positions before assembling. Carefully follow the order of assembly to ensure an easy installation. Wear proper safety gear including work shoes, gloves and goggles.. Remove protective plastic from both sides of panels Y9 and Y0. Place side to face toward the sun facing out when installing. Slide panels carefully into V-channels in corner profiles L0A and L0B and side profiles L03A and L03B. As you continue sliding the panels make sure they fit Y0 into the V-channels in base profiles L0C. Y9 Y0 Y9. Remove protective plastic from both sides of panels Y, Y and Y3. Place side to face toward the sun facing out when installing. Slide panels carefully into V-channels in gable profiles L03M, L03N, L03O, L03P and L03Q and into V-channels of front and back profiles L0I, L0J, L0K and L0L. As you continue sliding the panels make sure they fit into the V-channels in center roof profiles L0G. Y9 Y0 Y0 Y9 Y Y3 Y Y Y3 Y Y Y Y Remove protective plastic from EACH side of poly carbonate panels before installing. Dispose of plastic properly. Install with side labeled Face this side towards the sun FACING OUT. Panel IMPORTANT: Place rectangular cutout in corner of each panel Y so they meet at top front and top back corners. You will install two left and two right Ypanels. Panel #Y0 Panel #Y #Y9 #Y #Y3 9 of 55

52 Install Weather Stripping If you have been assembling your greenhouse in another place than it s final position, we recommend you move the greenhouse before you begin these steps. Have at least one person help you carry it. NOTE: You will find a roll of 80 meters of black rubber weather stripping. You will need a pair of scissors for this step. 3 From the outside of the greenhouse, line up the black rubber stripping with the V-channels of all profiles. Cut to length of each profile as you work, pushing the stripping between the panel and the empty space in the V-channel of the profile. IMPORTANT: The black rubber stripping J0A is cut to length with scissors. Make sure to insert stripping as shown, securely into the V-channels of all the profiles, cutting each piece to the proper length. This will help protect the inside of your greenhouse from the weather. Rubber Stripping #J0A 80M 50 of 55

Easy2Build TM. 8 x 10 Easy-Grow Greenhouse. Assembly Instructions. Smart Tech solutions

Easy2Build TM. 8 x 10 Easy-Grow Greenhouse. Assembly Instructions. Smart Tech solutions EasyBuild TM Smart Tech solutions 8 x 0 Easy-Grow Greenhouse Assembly Instructions 0 Structure 7 PC SHELL Systems Trading Corporation 50 7th Avenue Suite 809, New York, NY 03 Customer Service: (877) 07-900

More information

Easy2Build TM. 6 x 8 Easy-Grow Greenhouse. Assembly Instructions. Smart Tech solutions

Easy2Build TM. 6 x 8 Easy-Grow Greenhouse. Assembly Instructions. Smart Tech solutions EasyBuild TM Smart Tech solutions 6 x 8 Easy-Grow Greenhouse Assembly Instructions 0 S tr uct ure 7 PC SHELL Systems Trading Corporation 50 7th Avenue Suite 809, New York, NY 03 Customer Service: (877)

More information

Gazebo GZ620H. Assembly Instructions. Systems Trading Corporation

Gazebo GZ620H. Assembly Instructions. Systems Trading Corporation Gazebo GZ20H Assembly Instructions Systems Trading Corporation 0 7th Avenue Suite 2809, New York, NY 02 Customer service: (877)782 82 Email: easygrow@stcaustin.com of 20 Introduction Thank you for purchasing

More information

Pergola PR100N1. Assembly Instructions. Systems Trading Corporation Customer service: (877)

Pergola PR100N1. Assembly Instructions. Systems Trading Corporation Customer service: (877) FABRIC Pergola PR00N Assembly Instructions Systems Trading Corporation Customer service: (8)82 82 of 20 Introduction Thank you for purchasing the Pergola PR00N. When properly assembled and maintained,

More information

Gazebo GZ3584 Aluminum Composite Roof Panels

Gazebo GZ3584 Aluminum Composite Roof Panels Gazebo GZ8 Aluminum Composite Roof Panels Assembly Instructions 7 9 2 9 8 0 2 2 Systems Trading Corporation Customer service: (877)782 82 Email: easygrow@stcaustin.com of Introduction Thank you for purchasing

More information

11 x11 Pergola. Assembly Instructions. Paragon Group USA cm cm cm

11 x11 Pergola. Assembly Instructions. Paragon Group USA cm cm cm FABRIC x Pergola Assembly Instructions 0cm 9 2cm 0cm 0 20cm Paragon Group USA Customer Service:(8) 82 82 Email:cs-outdoors@paragongroupusa.com Introduction Thank you for purchasing the x Pergola. When

More information

Gazebo GZ584. Assembly Instructions. Paragon Group USA. Customer Service:(877)

Gazebo GZ584. Assembly Instructions. Paragon Group USA. Customer Service:(877) SU YESTE OL R P A Gazebo GZ NBRELL Assembly Instructions 0 9 max. 9 Paragon Group USA Customer Service:() Email:cs-outdoors@paragongroupusa.com Introduction Thank you for purchasing the Gazebo GZ. When

More information

Assembly Instructions

Assembly Instructions BR FA I C x Pergola Assembly Instructions 7 7 9 0 Paragon Group USA Customer Service:(877) 78 8 Email:cs-outdoors@paragongroupusa.com Introduction Thank you for purchasing the x Pergola. When properly

More information

Gazebo JH734. Systems Trading Corporation. ~ Products Through Innovation

Gazebo JH734. Systems Trading Corporation. ~ Products Through Innovation Gazebo JH734 Assembly Instructions Products Through Innovation Systems Trading Corporation 450 7th Avenue Suite 2809, New York, NY 10123 Customer service: (877)782 4482. Introduction Thank you for purchasing

More information

IMPORTANT!!! ASSEMBLY ASSEMBLY INSTRUCTIONS. (Internal Dimensions)

IMPORTANT!!! ASSEMBLY ASSEMBLY INSTRUCTIONS. (Internal Dimensions) ASSEMBLY ASSEMBLY INSTRUCTIONS (Internal Dimensions) Ent Spec Edition Ltr v-0- Overall dimensions including base: 7. L x 9 W x 0 H cms 97.5" L x 7" W x 8.7" H IMPORTANT!!! Please read these instructions

More information

GREENHOUSE EXTENSION 6 X4

GREENHOUSE EXTENSION 6 X4 ASSEMBLY INSTRUCTIONS GREENHOUSE EXTENSION 6 X Overall Dimensions (Approx.) 0 L x 93 W x 00 H cms 9" L x 76" W x 8.7" H 0 IMPORTANT You must read these instructions carefully before you start to assemble

More information

GREENHOUSE 6'x8' ASSEMBLY INSTRUCTIONS. (Internal Dimensions) Overall Dimensions (Approx.) L 193 W 200 H cms 97.5" L 76" W 78.

GREENHOUSE 6'x8' ASSEMBLY INSTRUCTIONS. (Internal Dimensions) Overall Dimensions (Approx.) L 193 W 200 H cms 97.5 L 76 W 78. ASSEMBLY INSTRUCTIONS GREENHOUSE 'x8' (Internal Dimensions) Overall Dimensions (Approx.) 7. L 9 W 00 H cms 97." L 7" W 78.8" H 0 IMPORTANT You must read these instructions carefully before you start to

More information

Assembly Instructions

Assembly Instructions Assembly Instructions Lean-To Greenhouse 129x68x165cm / 501/4"x263/4"x65" English_68467 Customer help and support line: 01302-380775 www.palramapplications.com EN IMPORTANT Please read these instructions

More information

Gardman Lean-to Greenhouse Assembly Instructions

Gardman Lean-to Greenhouse Assembly Instructions Page 1 Gardman Lean-to Greenhouse Assembly Instructions Our Help Line provides support and advice to customers of Summer Garden Buildings after ordering. For advice before you buy you can phone us free

More information

MonticelloTM. 4 Foot Extension Kit. Assembly Instructions. Made in the USA

MonticelloTM. 4 Foot Extension Kit. Assembly Instructions. Made in the USA MonticelloTM Made in the USA This kit extends the length of an assembled Monticello Greenhouse. The kit is installed at the back of the greenhouse. Each kit adds four feet in length. Make sure you have

More information

Greenhouse Assembly Instructions

Greenhouse Assembly Instructions Greenhouse Assembly Instructions Our Help Line provides support and advice to customers of Summer Garden Buildings after ordering. For advice before you buy you can phone us free 7 days a week on 0800

More information

Assembly and Installation Guide

Assembly and Installation Guide The Easy Hang Closet Solution SM Install Your elfa In An Instant. Enjoy The Benefits For A Lifetime. Basic Tools For elfa Assembly and Installation Level Hand or Power Drill Drill Bits 1/8", 3/8", 5/16"

More information

EmagiKit. Privacy Pod Plus. Quiet. Easy. Affordable. INSTRUCTIONS ASSEMBLY

EmagiKit. Privacy Pod Plus. Quiet. Easy. Affordable. INSTRUCTIONS ASSEMBLY EmagiKit Privacy Pod Plus Quiet. Easy. Affordable. INSTRUCTIONS ASSEMBLY DIMENSIONS AND COMPONENTS 47 47 Ceiling Unit 2-B 2-L 2-R Glass Door Corner Trim Door Handle 90 Adjustable Height Work Surface 1-B

More information

W6 series greenhouse

W6 series greenhouse W series greenhouse ssembly instructions Model W0 Model W07 Model W0 Model W Model W Walk-in Greenhouse Statement Dear Customer! May we congratulate you on your new Greenhouse. We feel sure that by following

More information

GrowSpan Estate Pro I Greenhouse

GrowSpan Estate Pro I Greenhouse GrowSpan Estate Pro I Greenhouse Photo may show a different but similar model. 2016 Growers Supply All Rights Reserved. Reproduction is prohibited without permission. STK# DIMENSIONS 104564 11'-8" W x

More information

GRANDIO G R E E N H O U S E S GRANDIO ELITE 8x12, 8x16, 8x20, 8x24 KIT MANUAL INCLUDES INSTRUCTIONS FOR BACK DOOR TRANSFORMATION

GRANDIO G R E E N H O U S E S GRANDIO ELITE 8x12, 8x16, 8x20, 8x24 KIT MANUAL INCLUDES INSTRUCTIONS FOR BACK DOOR TRANSFORMATION GRANDIO G R E E N H O U S E S 05 GRANDIO ELITE 8x, 8x6, 8x0, 8x4 KIT MANUAL INCLUDES INSTRUCTIONS FOR BACK DOOR TRANSFORMATION Grandio Elite 8x4 Shown In Image GREENHOUSE USER MANUAL 03 Grandio Greenhouses,

More information

Heavy Duty Ceiling Tilt Mount Installation Manual

Heavy Duty Ceiling Tilt Mount Installation Manual HD-CTM-5580 Heavy Duty Ceiling Tilt Mount Installation Manual *This Installation requires a minimum of two people. For your safety: Read the complete instruction manual before starting an installation

More information

SUPREME WALL GARDEN ASSEMBLY INSTRUCTIONS 24/08/16 www.hallsgreenhouses.com Please refer to website for the most up to date instructions. SAFETY WARNING 1. Always wear protective glasses, shoes, gloves

More information

Elite Home-Attached Greenhouse

Elite Home-Attached Greenhouse Elite Home-Attached Greenhouse Photo may show a greenhouse of a different length. Elite Home-Attached Greenhouse Use these instructions for the following greenhouses: #104711 #104713 #104715 2007 ClearSpan

More information

ClearSpan Mini Grab Bag Shelters

ClearSpan Mini Grab Bag Shelters ClearSpan Mini Grab Bag Shelters Photo may show a different but similar model. Baseboard is not included. 2008 ClearSpan All Rights Reserved. Reproduction is prohibited without permission. STK# DIMENSIONS

More information

GRANDIO G R E E N H O U S E S. Model GRA-812BR-GR. 8x12 GRANDIO ELITE GREENHOUSE USER MANUAL

GRANDIO G R E E N H O U S E S. Model GRA-812BR-GR. 8x12 GRANDIO ELITE GREENHOUSE USER MANUAL GRANDIO G R E E N H O U S E S Model GRA-8BR-GR 8x GRANDIO ELITE GREENHOUSE USER MANUAL 03 Grandio Greenhouses, Backyard Living Source Inc. All rights reserved GRANDIO G R E E N H O U S E S IMPORTANT! PLEASE

More information

C L A S S I C. Deluxe. Snow Thrower Cab. Assembly and Care Instructions

C L A S S I C. Deluxe. Snow Thrower Cab. Assembly and Care Instructions C L A S S I C Deluxe Snow Thrower Cab Assembly and Care Instructions Deluxe Snow Thrower Cab Assembly and Care Instructions Before you begin please unpack the carton and check that you have all your parts.

More information

GRANDIO G R E E N H O U S E S GRANDIO ASCENT 8x12, 8x16, 8x20, 8x24 KIT MANUAL INCLUDES INSTRUCTIONS FOR BACK DOOR TRANSFORMATION

GRANDIO G R E E N H O U S E S GRANDIO ASCENT 8x12, 8x16, 8x20, 8x24 KIT MANUAL INCLUDES INSTRUCTIONS FOR BACK DOOR TRANSFORMATION GRANDIO G R E E N H O U S E S 05 GRANDIO ASCENT 8x, 8x6, 8x0, 8x4 KIT MANUAL INCLUDES INSTRUCTIONS FOR BACK DOOR TRANSFORMATION Grandio Ascent 8x4 Shown In Image GREENHOUSE USER MANUAL 03 Grandio Greenhouses,

More information

Assembly Instructions

Assembly Instructions 8' x 6' x 6'6" Professional Growers Greenhouse Assembly Instructions Description Model # 8' x 6' x 6'6" Professional Growers Greenhouse PGG68 350351 Please read instructions COMPLETELY before assembly.

More information

ASSEMBLY INSTRUCTIONS MANUAL

ASSEMBLY INSTRUCTIONS MANUAL PAGE 1 OF 9 RECOMMENDED TOOLS FOR ASSEMBLY: ALLEN WRENCH (INCLUDED) BOX WRENCH (INCLUDED) PHILLIPS SCREW DRIVER (NOT INCLUDED) PARTS IN CARTON: ALLEN WRENCH SCREWS (20 EACH) ROUND HEAD SCREWS (8 EACH)

More information

General Features. Low Profile. The SMART BOXX stands only 1.5 off of the bed of your truck so cargo space is maximized

General Features. Low Profile. The SMART BOXX stands only 1.5 off of the bed of your truck so cargo space is maximized General Features Low Profile. The SMART BOXX stands only 1.5 off of the bed of your truck so cargo space is maximized Two Sizes Short Box :74 L X 47 W X 7 T and Long Box 92 L X 47 W X 7 T All Aluminium

More information

Assembly instructions. 6x4. Model GH1354A. 6x6. Model GH1357A. 6x8. Model GH1360A. 6x10. Walk-in Greenhouse. Model GH1363A

Assembly instructions. 6x4. Model GH1354A. 6x6. Model GH1357A. 6x8. Model GH1360A. 6x10. Walk-in Greenhouse. Model GH1363A ssembly instructions x Model GH x Model GH7 x8 Model GH0 x0 Model GH Walk-in Greenhouse Statement ear Customer! May we congratulate you on your new Greenhouse. We feel sure that by following the detailed

More information

ClearSpan Attached-Style Awning

ClearSpan Attached-Style Awning ClearSpan Attached-Style Awning Photo may show a different but similar model. 2007 ClearSpan All Rights Reserved. Reproduction is prohibited without permission. Revision date: July 2007ldg STK# DIMENSIONS

More information

ClearSpan Mini Cold Frames

ClearSpan Mini Cold Frames ClearSpan Mini Cold Frames Photo may show a different but similar model. 2009 ClearSpan All Rights Reserved. Reproduction is prohibited without permission. STK# DIMENSIONS 105152 6' W x 5' H x 6' L 105153

More information

GRANDIO G R E E N H O U S E S GRANDIO ELITE 8x12, 8x16, 8x20, 8x24 KITS. Grandio Elite 8x24 Shown In Image GREENHOUSE USER MANUAL

GRANDIO G R E E N H O U S E S GRANDIO ELITE 8x12, 8x16, 8x20, 8x24 KITS. Grandio Elite 8x24 Shown In Image GREENHOUSE USER MANUAL GRANDIO G R E E N H O U S E S 05 GRANDIO ELITE 8x, 8x6, 8x0, 8x4 KITS Grandio Elite 8x4 Shown In Image GREENHOUSE USER MANUAL 03 Grandio Greenhouses, Backyard Living Source Inc. All rights reserved 05

More information

Before Assembling the Storage Wall

Before Assembling the Storage Wall Chapter 1 Assembling the Lista Storage Wall Lista provides two types of standard Storage Walls: B251 and B255. The design, construction, assembly, and quality are identical for both types, however, B251

More information

E N G L I S H GARDEN SHED. Assembly Instructions. Suitable for Models WITH VARYING DEPTHS

E N G L I S H GARDEN SHED. Assembly Instructions. Suitable for Models WITH VARYING DEPTHS GARDEN SHED Assembly Instructions Suitable for Models 6' Wide 8' Wide 0' Wide WITH VARYING DEPTHS GI0003 November 0 INSTALLATION ADVICE It's Not That Difficult! The construction of your shed isn't as complicated

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS For Wallbed models: Do-It-Yourself BOOKLET #C90 WARNING! ALL MURPY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION

More information

INSTRUCTION BOOKLET #34. For Wallbed models: KING SIZE SIERRA WITH STORAGE HEADBOARD

INSTRUCTION BOOKLET #34. For Wallbed models: KING SIZE SIERRA WITH STORAGE HEADBOARD For Wallbed models: KING SIZE SIERRA WITH STORAGE HEADBOARD INSTRUCTION BOOKLET #34 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION

More information

CABINETRY Assembly Instructions

CABINETRY  Assembly Instructions www.hdicabinetry.com Assembly Instructions TABLE OF CONTENTS Category Page(s) Section 1: Framed Series Base Cabinet Instructions Wall Cabinet Instructions Easy Reach Cabinet Instructions 1.01-1.04 1.05-1.06

More information

LAWN AND GARDEN GREENHOUSE

LAWN AND GARDEN GREENHOUSE MODELS# OG0AL8-BKE OGAL-8 OGrow Walk-in ' x 8' LAWN AND GARDEN GREENHOUSE With Heavy Duty Aluminium Frame MANUAL VERSION # Grow r! e h t e g To Let's Thank you for purchasing the OGROW greenhouse Follow

More information

GRANDIO G R E E N H O U S E S GRANDIO ASCENT 8x12, 8x16, 8x20, 8x24 KIT MANUAL INCLUDES INSTRUCTIONS FOR BACK DOOR TRANSFORMATION

GRANDIO G R E E N H O U S E S GRANDIO ASCENT 8x12, 8x16, 8x20, 8x24 KIT MANUAL INCLUDES INSTRUCTIONS FOR BACK DOOR TRANSFORMATION GRANDIO G R E E N H O U S E S 05 GRANDIO ASCENT 8x, 8x6, 8x0, 8x4 KIT MANUAL INCLUDES INSTRUCTIONS FOR BACK DOOR TRANSFORMATION Grandio Ascent 8x4 Shown In Image GREENHOUSE USER MANUAL 03 Grandio Greenhouses,

More information

SteelChief Installation Instructions for pre-assembled panel form sheds GABLE ROOF

SteelChief Installation Instructions for pre-assembled panel form sheds GABLE ROOF SteelChief Installation Instructions for pre-assembled panel form sheds GABLE ROOF Please read fully before commencing work...any queries will be promptly answered, contact theboss@steelchief.com.aui MPORTANT

More information

ClearSpan PolyMax Windbreak Wall

ClearSpan PolyMax Windbreak Wall ClearSpan PolyMax Windbreak Wall Photo may show a different but similar model. 2007 ClearSpan All Rights Reserved. Reproduction is prohibited without permission. Revision date: February 2007ldg STK# DIMENSIONS

More information

Kawasaki Teryx 750 Cab Kit* Caution: Before using this product, read this manual and follow all Safety Instructions.

Kawasaki Teryx 750 Cab Kit* Caution: Before using this product, read this manual and follow all Safety Instructions. Owner s Manual Model: Kawasaki Teryx 750 Kawasaki Teryx 750 Cab Kit* Caution: Before using this product, read this manual and follow all Safety Instructions. Safety Instructions Cab Kit Contents Hardware

More information

Version 2016_1.1 VICTORIAN ASSEMBLY INSTRUCTIONS. Victorian Vi-23, 34, 36

Version 2016_1.1 VICTORIAN ASSEMBLY INSTRUCTIONS. Victorian Vi-23, 34, 36 Version 2016_1.1 VICTORIAN ASSEMBLY INSTRUCTIONS Victorian Vi-23, 34, 36 PRODUCT INFORMATION Dear customer, Thank you for buying a high-quality aluminium greenhouse. REMARKS The drawings in these instructions

More information

ClearSpan End Frame Kit 26' Wide x 12' High

ClearSpan End Frame Kit 26' Wide x 12' High ClearSpan End Frame Kit 26' Wide x 12' High Diagram shows the end frame kit for an end wall without a door. (Door and end panel are purchased separately.) Rafter and struts shown in the above diagram are

More information

Triplex Instructions for Packing and Unpacking

Triplex Instructions for Packing and Unpacking 2-8-8-2 Triplex Instructions for Packing and Unpacking It is recommended that you review all these instructions before removing the engine or tender from the poly foam container. www.mthtrains.com Table

More information

LAWN AND GARDEN GREENHOUSE

LAWN AND GARDEN GREENHOUSE MODEL# OGAL-66 OGrow Walk-in 6' x ' LAWN AND GARDEN GREENHOUSE With Heavy Duty Aluminium Frame Let'sGrow Together! Thank you for purchasing the OGROW greenhouse Follow the assembly and safety instructions

More information

GROWING BETTER THROUGH DESIGN. 6ft Lean-To LEAN-TO. Assembly Instructions 04/02

GROWING BETTER THROUGH DESIGN. 6ft Lean-To LEAN-TO. Assembly Instructions 04/02 GROWING BETTER THROUGH DESIGN 6ft Lean-To LEAN-TO Assembly Instructions 04/02 6ft Lean-To Greenhouse Base Plan Introduction/Tools/Contents / / Contents This is a copy of our Lean-To greenhouse base plan.

More information

WILDING WALLBEDS INSTALLATION INSTRUCTION Side Mount

WILDING WALLBEDS INSTALLATION INSTRUCTION Side Mount WILDING WALLBEDS INSTALLATION INSTRUCTION Side Mount For Wallbed models: Do-It-Yourself Insturction booklet C92 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE

More information

40 & 50 Foot PS-1 Box Car Assembly Instructions

40 & 50 Foot PS-1 Box Car Assembly Instructions 40 & 50 Foot PS-1 Box Car Instructions Push the #2100 coupler/stirrup assembly onto the ends of the metal floor. Slide them into the slots and slightly lift the ends (wings), then press firmly on the front

More information

English/French 06/04

English/French 06/04 E000 PLEASE READ ASSEMBLY INSTRUCTIONS COMPLETELY BEFORE ASSEMBLING YOUR BUILDING CAUTION: Some parts have sharp edges. Care must be taken when handling the various pieces to avoid a mishap. For safety

More information

Assembly Instructions

Assembly Instructions Unite Panel System Hinge Door July 2016 #12 x / slotted hex washer head bolt Figure 1 threshold bracket frame Detail F threshold bracket threshold bracket (installed) #12 x / slotted hex washer head bolt

More information

INSTRUCTION BOOKLET #C0 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY.

More information

WOLF PUP LOOM TM & WOLF PUP LT LOOM TM

WOLF PUP LOOM TM & WOLF PUP LT LOOM TM WOLF PUP LOOM TM & WOLF PUP LT LOOM TM Assembly Instructions FL3000 FL3006 FL3009 WOLF PUP WOLF PUP LT Find out more at schachtspindle.com Schacht Spindle Company 6101 Ben Place Boulder, CO 80301 p. 303.442.3212

More information

EASY POOL STEP (NE113)

EASY POOL STEP (NE113) EASY POOL STEP (NE113) FOR USE WITH: EASY POOL STEP (NE113) (1 CARTON) EASY POOL STEP WITH OUTSIDE LADDER (NE126) EASY POOL STEP ENTRY SYSTEM (NE138) (With Gate) (4 CARTONS) Above are the options available

More information

INSTALLATION INSTRUCTIONS LS X 12-2 X 7 1/2 FRAME LOAFING SHED

INSTALLATION INSTRUCTIONS LS X 12-2 X 7 1/2 FRAME LOAFING SHED INSTALLATION INSTRUCTIONS LS-12 12 X 12-2 X 7 1/2 FRAME ACTUAL FRAME BASE SIZE: 12 X 12-2 LOAFING SHED Our unique assembly process quickly transforms the individual pieces into a finished structure that

More information

EASY-IN POOL STEP SYSTEM NE132

EASY-IN POOL STEP SYSTEM NE132 EASY-IN POOL STEP SYSTEM NE132 This instruction manual features multiple guides for the step unit components. 7939 EASY POOL STEP (NE113) FOR USE WITH: EASY-IN POOL STEP (NE126) 6492 PARTS & HARDWARE FOR

More information

GlideRite Retractable Cover System For HotSpring & Tiger River Spas (except Classic & pre-2000 Landmark Spas)

GlideRite Retractable Cover System For HotSpring & Tiger River Spas (except Classic & pre-2000 Landmark Spas) List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.

More information

INSTRUCTION BOOKLET #C10 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY.

More information

Installing Brackets to Minimize Distortion in Your SMART Board 685ix Interactive Whiteboard System s Projected Image

Installing Brackets to Minimize Distortion in Your SMART Board 685ix Interactive Whiteboard System s Projected Image UX60-RFK-685 Installing Brackets to Minimize Distortion in Your SMART Board 685ix Interactive Whiteboard System s Projected Image Follow these instructions to install brackets on your SMART Board 685ix

More information

WeatherShield Covered Walkway and Connect-A-Building

WeatherShield Covered Walkway and Connect-A-Building WeatherShield Covered Walkway and Connect-A-Building Photo may show a different but similar model. 2014 ClearSpan All Rights Reserved. Reproduction is prohibited without permission. STK# DIMENSIONS 104303

More information

ClearSpan Mini Grab Bag Shelters

ClearSpan Mini Grab Bag Shelters ClearSpan Mini Grab Bag Shelters Photo may show a different but similar model. Baseboard is not included. 2008 ClearSpan All Rights Reserved. Reproduction is prohibited without permission. STK# DIMENSIONS

More information

ClearSpan Grab Bag Canopy

ClearSpan Grab Bag Canopy ClearSpan Grab Bag Canopy Photo may show a different but similar model. 2008 ClearSpan All Rights Reserved. Reproduction is prohibited without permission. STK# DIMENSIONS 104385 10 W x 20 L 1 YOU MUST

More information

400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS

400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS 12/11/07 PAGE 1 OF 12 400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS Thank you for purchasing our product! *Please read these instructions

More information

Premium Solar Star Greenhouse

Premium Solar Star Greenhouse Premium Solar Star Greenhouse Assembly Instructions SKU# 104901 2006 ClearSpan All rights reserved. Reproduction without permission is prohibited. Revision date: March 2006g Contact your sales representative

More information

ASSEMBLY INSTRUCTIONS FOR STORETTE STA42

ASSEMBLY INSTRUCTIONS FOR STORETTE STA42 ASSEMBLY INSTRUCTIONS FOR STORETTE STA42 A01 CAUTION: Some parts have sharp edges. Care must be taken when handling the various pieces to avoid a mishap. For safety sake, please read the safety information

More information

TOOLS REQUIRED: HARDWARE INCLUDED: 13MM FLAT WRENCH FOR LEVELING THE STRUCTURE RATCHET WITH 5MM HEX BIT FOR CORNER SCREWS ON TOP TRAVERSE BEAMS

TOOLS REQUIRED: HARDWARE INCLUDED: 13MM FLAT WRENCH FOR LEVELING THE STRUCTURE RATCHET WITH 5MM HEX BIT FOR CORNER SCREWS ON TOP TRAVERSE BEAMS 1 TOOLS REQUIRED: RATCHET WITH 5MM HEX BIT FOR CORNER SCREWS ON TOP TRAVERSE BEAMS 13MM FLAT WRENCH FOR LEVELING THE STRUCTURE RUBBER MALLET FOR INSERTING PANELS 8MM HEX BIT WITH EXTENSION FOR HEX BOLT

More information

8 Wide Evolution Cedar Partition Assembly Instructions

8 Wide Evolution Cedar Partition Assembly Instructions 09/13 8 Wide Evolution Cedar Partition Assembly Instructions Contents: Introduction Overview Base Preparation Partition Frame Assembly Glazing Door Installation Parts List Section - 1 2 3 4 5 Page 3 4

More information

Steele TV Stand Stock # BH

Steele TV Stand Stock # BH LOT NUMBER: DATE PURCHASED: / / Steele TV Stand Stock # BH46-084-899-02 ADULT ASSEMBLY REQUIRED If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the store

More information

ClearSpan End Frame Kit 30' Wide x 11' High

ClearSpan End Frame Kit 30' Wide x 11' High ClearSpan End Frame Kit 30' Wide x 11' High Diagram shows the end frame kit for an end wall without a door. (Door and end panel are purchased separately.) Rafter and mounting feet shown in the above diagram

More information

GRANDIO G R E E N H O U S E S GRANDIO ASCENT 8x12, 8x16, 8x20, 8x24 KITS. Grandio Ascent 8x24 Shown In Image GREENHOUSE USER MANUAL

GRANDIO G R E E N H O U S E S GRANDIO ASCENT 8x12, 8x16, 8x20, 8x24 KITS. Grandio Ascent 8x24 Shown In Image GREENHOUSE USER MANUAL GRANDIO G R E E N H O U S E S 05 GRANDIO ASCENT 8x, 8x6, 8x0, 8x4 KITS Grandio Ascent 8x4 Shown In Image GREENHOUSE USER MANUAL 03 Grandio Greenhouses, Backyard Living Source Inc. All rights reserved 05

More information

Please read these instructions before use and keep for future reference

Please read these instructions before use and keep for future reference Wardrobe Assembly Guide Allen Key Provided (if required) Philips Screwdriver Required Hammer Required Please read these instructions before use and keep for future reference Caution! Two Person Assembly

More information

INSTRUCTION BOOKLET #C21. For Wallbed models: KING SIZE

INSTRUCTION BOOKLET #C21. For Wallbed models: KING SIZE For Wallbed models: KING SIZE INSTRUCTION BOOKLET #C1 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT

More information

Interactive Monitor Arm

Interactive Monitor Arm Interactive Monitor Arm Tools Required -5mm Allen wrench -Phillips screwdriver -Plastic mallet There are two ways to attach a Monitor Arm to a Full Frame; with a Beam, or with a Post Mount. Both methods

More information

Side Mount INSTRUCTION BOOKLET #C122 BED STYLE: PARK CITY

Side Mount INSTRUCTION BOOKLET #C122 BED STYLE: PARK CITY Side Mount BED STYLE: PARK CITY INSTRUCTION BOOKLET #C1 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT

More information

Installation Guide. Bi-fold Doors

Installation Guide. Bi-fold Doors Installation Guide Bi-fold Doors Installation Guide Components box 1. 6. 2. 3. 7. 5. 4. 8. Contents 1. Fixing plugs 2. Wedge gasket 3. Bottom trolley 4. Top trolley 5. Magnetic keep (x 2 if door height

More information

INSTALLATION INSTRUCTIONS LS X 12-2 X 7 1/2 FRAME LOAFING SHED

INSTALLATION INSTRUCTIONS LS X 12-2 X 7 1/2 FRAME LOAFING SHED INSTALLATION INSTRUCTIONS LS-30 30 X 12-2 X 7 1/2 FRAME ACTUAL FRAME BASE SIZE: 30 X 12-2 LOAFING SHED Our unique assembly process quickly transforms the individual pieces into a finished structure that

More information

https://www.wallbedsbywilding.com/wallbed-installation-studio-series/

https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ For Wallbed models: KING SIZE INSTRUCTION BOOKLET #C1 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED

More information

Installation Instructions

Installation Instructions by Plato Woodwork Installation Instructions Plato Woodwork, Inc. 200 Third Street SW P.O. Box 98 Plato, MN 55370 www.platowoodwork.com 800.328.5924 SECTION GUIDE GETTING STARTED PAGE # Installation Methods...

More information

Extension Standard building 10/14

Extension Standard building 10/14 Standard building Extension 10/14 8 Wide Victorian Cedar Greenhouse Extension Assembly Instructions Contents: Introduction Base Preparation Overview Base Assembly Side Assembly Frame Assembly Door Installation

More information

RAMPAGE P R O D U C T S. INSTALLATION INSTRUCTIONS BRONCO ZIPPER FASTRACK TOP PART #984xx BRONCO TOOLS REQUIRED

RAMPAGE P R O D U C T S. INSTALLATION INSTRUCTIONS BRONCO ZIPPER FASTRACK TOP PART #984xx BRONCO TOOLS REQUIRED RAMPAGE P R O D U C T S 84 (+/- 1/4 ) INSTALLATION INSTRUCTIONS BRONCO ZIPPER FASTRACK TOP PART #984xx BRONCO 1966-1977 TOOLS REQUIRED 3/8 WRENCH 7/16 WRENCH ½ WRENCH #2 PHILLIPS SCREWDRIVER 1/8 DRILL

More information

Linear Hook- on Worksurfaces

Linear Hook- on Worksurfaces Linear Hook- on Worksurfaces Linear Hook-On Worksurfaces come in three depths and seven lengths. Different worksurfaces have different reqirements for installation that are outlined below. 27 inch deep

More information

TIP FOR GETTING STARTED

TIP FOR GETTING STARTED Tip for getting started TIP FOR GETTING STARTED Be careful not to drill into any electrical wires, ductwork, plumbing or other damagable components. If you have any questions on the locations of these

More information

Walk-in Greenhouse. Assembly instructions. 6x4. 6x6. 6x8. Model GH0490 Model GH0491 Model GH1040. Model GH0492 Model GH0493 Model GH1041

Walk-in Greenhouse. Assembly instructions. 6x4. 6x6. 6x8. Model GH0490 Model GH0491 Model GH1040. Model GH0492 Model GH0493 Model GH1041 ssembly instructions x4 Model GH0490 Model GH049 Model GH040 x Model GH049 Model GH049 Model GH04 x Model GH0494 Model GH049 Model GH04 Walk-in Greenhouse Statement Congratulations on purchasing your new

More information

10 Octagon Cedar Gazebo Assembly Instructions

10 Octagon Cedar Gazebo Assembly Instructions 10 Octagon Cedar Gazebo Assembly Instructions Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST www.homeplacestructures.com Package ships as shown revised 06/22/09 10 Cedar Gazebo Assembly Instructions

More information

OPERATOR'S MANUAL 46" SNOW BLADE. Model Numbers OEM IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY

OPERATOR'S MANUAL 46 SNOW BLADE. Model Numbers OEM IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY OPERATOR'S MANUAL 46" SNOW BLADE Model Numbers 190-833-OEM IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY MTD PRODUCTS INC. P.O. BOX 368022 CLEVELAND, OHIO 44136-9722 PRINTED IN U.S.A. FORM NO.

More information

12 Wide Evolution Cedar Partition Assembly Instructions

12 Wide Evolution Cedar Partition Assembly Instructions 06/13 12 Wide Evolution Cedar Partition Assembly Instructions Contents: Introduction Base Preparation Side Assembly Glazing Door Installation Frame Finishing Section - 1 2 3 4 5 Page 3 4 5-6 7 8-9 10-14

More information

Laminate Cabinet Installation Instructions

Laminate Cabinet Installation Instructions Laminate Cabinet Installation Instructions www.easygaragestorage.com/installation How To Use These Instructions Thank you for your purchase! Please read each step of this manual thoroughly to ensure proper

More information

GrowSpan Series 500 Roll-Up Ends

GrowSpan Series 500 Roll-Up Ends GrowSpan Series 500 Roll-Up Ends Photo may show a different but similar model. Doorframe materials are not included. 2016 Growers Supply All Rights Reserved. Reproduction is prohibited without permission.

More information

Model No. EP84-A, EP84AR-A, P84L

Model No. EP84-A, EP84AR-A, P84L E000 Model No. EP84-A, EP84AR-A, P84L PLEASE READ ASSEMBLY INSTRUCTIONS COMPLETELY BEFORE ASSEMBLING YOUR BUILDING CAUTION: Some parts have sharp edges. Care must be taken when handling the various pieces

More information

PERSONAL RECORD KEEPING

PERSONAL RECORD KEEPING 2 P R O 3 7 0 A s s e m b l y i n s t r u c t i o n s PERSONAL RECORD KEEPING Tip: Record the serial numbers of your Octane Fitness elliptical in the spaces below. This will make it easier for you to obtain

More information

Assembly Guide for Series 500 Ridge Vent Kits

Assembly Guide for Series 500 Ridge Vent Kits Assembly Guide for Series 500 Ridge Vent Kits Photo shows a sample ridge vent as installed on a greenhouse. Actual building and ridge vent length may differ. 2014 ClearSpan All Rights Reserved. Reproduction

More information

ASSEMBLY GUIDE. Mia Narrow Bookcase

ASSEMBLY GUIDE. Mia Narrow Bookcase ASSEMBLY GUIDE Mia Narrow Bookcase Components: Upon unpacking your bookcase from it s delivery box, you should have the pieces shown. Follow the steps on the next pages to assemble your new bookcase. Step

More information

INSTALLATION INSTRUCTIONS LS X 12-2 X 7 1/2 FRAME LOAFING SHED

INSTALLATION INSTRUCTIONS LS X 12-2 X 7 1/2 FRAME LOAFING SHED INSTALLATION INSTRUCTIONS LS-24 24 X 12-2 X 7 1/2 FRAME ACTUAL FRAME BASE SIZE: 24 X 12-2 LOAFING SHED Our unique assembly process quickly transforms the individual pieces into a finished structure that

More information

INSTRUCTION BOOKLET #C20

INSTRUCTION BOOKLET #C20 INSTRUCTION BOOKLET #C0 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT IN SEVERE PERSONAL INJURY TO

More information

Walk-in Greenhouse. Assembly instructions. 8x6. 8x8. 8x10. 8x12. Model GH1399A Model GH1400A. Model GH1402A Model GH1403A. Model GH1405A Model GH1406A

Walk-in Greenhouse. Assembly instructions. 8x6. 8x8. 8x10. 8x12. Model GH1399A Model GH1400A. Model GH1402A Model GH1403A. Model GH1405A Model GH1406A Assembly instructions 8x6 Model GH1399A Model GH1400A 8x8 Model GH1402A Model GH1403A 8x10 Model GH1405A Model GH1406A 8x12 Model GH1408A Model GH1409A Walk-in Greenhouse Statement Dear Customer! May we

More information

10' W x 8' H or 10' H Round Style Shelter Assembly Instructions

10' W x 8' H or 10' H Round Style Shelter Assembly Instructions 10' W x 8' H or 10' H Round Style Shelter Assembly Instructions Description 10' x 8' x 8' Round Style Shelter - Gray 10' x 8' x 10' Round Style Shelter - Gray Recommended Tools Please read instructions

More information

INSTALLATION MANUAL PBL-UMP

INSTALLATION MANUAL PBL-UMP INSTALLATION MANUAL PBL-UMP Table of Contents Warning Statements... 4 Parts List... 5 Installation Tools... 5 Features... 7 Projector Preparation... 8 Bracket Installation... 10 Leveling the Mounting Bracket...

More information