MC14521B. MARKING DIAGRAMS. MAXIMUM RATINGS (Voltages Referenced to V SS ) (Note 2.) ORDERING INFORMATION PDIP 16 P SUFFIX CASE 648
|
|
- Edmund Higgins
- 5 years ago
- Views:
Transcription
1 The MC452B consists of a chain of 24 flip flops with an input circuit that allows three modes of operation. The input will function as a crystal oscillator, an RC oscillator, or as an input buffer for an external oscillator. Each flip flop divides the frequency of the previous flip flop by two, consequently this part will count up to 2 24 = 6,777,26. The count advances on the negative going edge of the clock. The outputs of the last seven stages are available for added flexibility. All Stages are Resettable Reset Disables the RC Oscillator for Low Standby Power Drain RC and Crystal Oscillator Outputs Are Capable of Driving External Loads Test Mode to Reduce Test Time V DD and V SS Pins Brought Out on Crystal Oscillator Inverter to Allow the Connection of External Resistors for Low Power Operation Supply Voltage Range = 3. Vdc to 8 Vdc Capable of Driving Two Low power TTL Loads or One Low power Schottky TTL Load over the Rated Temperature Range. PDIP 6 P SUFFIX CASE 648 SOIC 6 D SUFFIX CASE 75B SOEIAJ 6 F SUFFIX CASE 966 MARKING DIAGRAMS MC452BCP AWLYYWW 452B AWLYWW MC452B ALYW MAXIMUM RATINGS (Voltages Referenced to V SS ) (Note 2.) Symbol Parameter Value Unit V DD DC Supply Voltage Range.5 to +8. V V in, V out Input or Output Voltage Range (DC or Transient).5 to V DD +.5 V A WL, L YY, Y WW, W = Assembly Location = Wafer Lot = Year = Work Week I in, I out P D Input or Output Current (DC or Transient) per Pin Power Dissipation, per Package (Note 3.) ± ma 5 mw T A Ambient Temperature Range 55 to +25 C T stg Storage Temperature Range 65 to + C T L Lead Temperature (8 Second Soldering) 26 C 2. Maximum Ratings are those values beyond which damage to the device may occur. 3. Temperature Derating: Plastic P and D/DW Packages: 7. mw/c From 65C To 25C This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high impedance circuit. For proper operation, V in and V out should be constrained to the range V SS (V in or V out ) V DD. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either V SS or V DD ). Unused outputs must be left open. ORDERING INFORMATION Device Package Shipping MC452BCP PDIP 6 2/Box MC452BD SOIC 6 48/Rail MC452BDR2 SOIC 6 25/Tape & Reel MC452BF SOEIAJ 6 See Note. MC452BFEL SOEIAJ 6 See Note. MC452BFR2 SOEIAJ 6 See Note.. For ordering information on the EIAJ version of the SOIC packages, please contact your local ON Semiconductor representative. Semiconductor Components Industries, LLC, 2 August, 2 Rev. 4 Publication Order Number: MC452B/D
2 PIN ASSIGNMENT BLOCK DIAGRAM Output Count Capacity Q8 2 8 = 262,44 Q9 2 9 = 524,288 Q2 2 2 =,48,576 Q2 2 2 = 2,97,2 Q = 4,94,34 Q = 8,388,68 Q = 6,777,26 2
3 ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ELECTRICAL CHARACTERISTICS (Voltages Referenced to V SS ) Characteristic Output Voltage V in = V DD or Level Symbol V OL V Level V in = or V DD OH Input Voltage Level (V O = 4.5 or.5 Vdc) (V O = 9. or. Vdc) (V O = 3.5 or.5 Vdc) (V O =.5 or 4.5 Vdc) (V O =. or 9. Vdc) (V O =.5 or 3.5 Vdc) Level Output Drive Current (V OH = 2.5 Vdc) Source (V OH = 4.6 Vdc) Pins 4 & 7 (V OH = 9.5 Vdc) (V OH = 3.5 Vdc) (V OH = 2.5 Vdc) Source (V OH = 4.6 Vdc) Pins,, (V OH = 9.5 Vdc), 2, 3, 4 (V OH = 3.5 Vdc) and (V OL =.4 Vdc) Sink (V OL =.5 Vdc) (V OL =.5 Vdc) V IL V IH I OH 55C 25C 25C V DD Vdc Min Max Min Typ (4.) Max Min Max Unit I OL Input Current I in ±. ±. ±. ±. µadc Input Capacitance (V in = ) C in 7.5 pf Vdc Vdc Vdc Vdc madc madc madc Quiescent Current (Per Package) Total Supply Current (5.) (6.) (Dynamic plus Quiescent, Per Package) (C L = 5 pf on all outputs, all buffers switching) I DD I T I T = (.42 µa/khz) f + I DD I T = (.85 µa/khz) f + I DD I T = (.4 µa/khz) f + I DD 4. Data labelled Typ is not to be used for design purposes but is intended as an indication of the IC s potential performance. 5. The formulas given are for the typical characteristics only at 25C. 6. To calculate total supply current at loads other than 5 pf: I T (C L ) = I T (5 pf) + (C L 5) Vfk where: I T is in µa (per package), C L in pf, V = (V DD V SS ) in volts, f in khz is input frequency, and k = µadc µadc 3
4 ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ SWITCHING CHARACTERISTICS (7.) (C L = 5 pf, T A = 25C) Characteristic Output Rise and Fall Time (Counter Outputs) t TLH, t THL = (.5 ns/pf) C L + 25 ns t TLH, t THL = (.75 ns/pf) C L ns t TLH, t THL = (.55 ns/pf) C L ns Propagation Delay Time Clock to Q8 t PHL, t PLH = (.7 ns/pf) C L + 44 ns t PHL, t PLH = (.66 ns/pf) C L ns t PHL, t PLH = (.5 ns/pf) C L ns Symbol t TLH, t THL t PHL, t PLH V DD Vdc Min Typ (8.) Max Unit ns µs Clock to Q24 t PHL, t PLH = (.7 ns/pf) C L + 59 ns t PHL, t PLH = (.66 ns/pf) C L ns t PHL, t PLH = (.5 ns/pf) C L ns Propagation Delay Time Reset to Q n t PHL = (.7 ns/pf) C L + 2 ns t PHL = (.66 ns/pf) C L ns t PHL = (.5 ns/pf) C L + 35 ns t PHL Clock Pulse Width t WH(cl) Clock Pulse Frequency f cl Clock Rise and Fall Time t TLH, t THL Reset Pulse Width t WH(R) Reset Removal Time t rem The formulas given are for the typical characteristics only at 25C. 8. Data labelled Typ is not to be used for design purposes but is intended as an indication of the IC s potential performance ns ns MHz µs ns ns µ µ Figure. Power Dissipation Test Circuit and Waveform 4
5 Figure 2. Switching Time Test Circuit and Waveforms * Optional for low power operation, kω R 7 kω. Figure 3. Crystal Oscillator Circuit Characteristic 5 khz Circuit Crystal Characteristics Resonant Frequency Equivalent Resistance, R S 5. External Resistor/Capacitor Values R o C T C S Frequency Stability Frequency Change as a Function of V DD (T A = 25C) V DD Change from V to V V DD Change from V to V Frequency Change as a Function of Temperature (V DD = V) T A Change from 55C to + 25C MC452 only Complete Oscillator* T A Change from +25C to+25c MC452 only Complete Oscillator* khz Circuit Unit khz kω kω pf pf ppm ppm ppm ppm ppm ppm *Complete oscillator includes crystal, capacitors, and resistors. ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ Figure 4. Typical Data for Crystal Oscillator Circuit 5
6 Figure 5. RC Oscillator Stability Ω Ω Ω µ Figure 6. RC Oscillator Frequency as a Function of R TC and C Figure 7. RC Oscillator Circuit Figure 8. Functional Test Circuit 6
7 ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ FUNCTIONAL TEST SEQUENCE A test function (see Figure 8) has been included for the reduction of test time required to exercise all 24 counter stages. This test function divides the counter into three 8 stage sections, and 255 counts are loaded in each of the 8 stage sections in parallel. All flip flops are now at a logic. The counter is now returned to the normal 24 stages in series configuration. One more pulse use is entered e ed into Input 2 (In 2) which will cause the counter to ripple from an all state to an all state. Inputs Outputs Comments Reset In 2 Out 2 V SS V DD Q8 thru Q24 Counter is in three 8 stage sections in parallel mode Counter is reset. In 2 and V DD Gnd Out 2 are connected together First to transition on In 2, Out 2 node. Gnd V DD 255 to transitions are clocked into this In 2, Out 2 node. The 255th to transition. Counter converted back to 24 stages in series mode. Out 2 converts back to an output. Counter ripples from an all state to an all stage. 7
8 LOGIC DIAGRAM 8
9 PACKAGE DIMENSIONS H A G B F C S K D 6 PL PDIP 6 P SUFFIX PLASTIC DIP PACKAGE CASE ISSUE R T J L M 9
10 PACKAGE DIMENSIONS T G A D 6 PL K B C SOIC 6 D SUFFIX PLASTIC SOIC PACKAGE CASE 75B 5 ISSUE J P 8 PL M R X 45 J F
11 PACKAGE DIMENSIONS e Z D b E A H E A SOEIAJ 6 F SUFFIX PLASTIC EIAJ SOIC PACKAGE CASE 966 ISSUE O VIEW P M L E Q L DETAIL P c
12 ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Typical parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including Typicals must be validated for each customer application by customer s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. PUBLICATION ORDERING INFORMATION NORTH AMERICA Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 563, Denver, Colorado 827 USA Phone: or Toll Free USA/Canada Fax: or Toll Free USA/Canada ONlit@hibbertco.com Fax Response Line: or Toll Free USA/Canada N. American Technical Support: Toll Free USA/Canada EUROPE: LDC for ON Semiconductor European Support German Phone: (+) (Mon Fri 2:3pm to 7:pm CET) ONlit german@hibbertco.com French Phone: (+) (Mon Fri 2:pm to 7:pm CET) ONlit french@hibbertco.com English Phone: (+) (Mon Fri 2:pm to 5:pm GMT) ONlit@hibbertco.com EUROPEAN TOLL FREE ACCESS*: *Available from Germany, France, Italy, UK CENTRAL/SOUTH AMERICA: Spanish Phone: (Mon Fri 8:am to 5:pm MST) ONlit spanish@hibbertco.com ASIA/PACIFIC: LDC for ON Semiconductor Asia Support Phone: (Tue Fri 9:am to :pm, Hong Kong Time) Toll Free from Hong Kong & Singapore: ONlit asia@hibbertco.com JAPAN: ON Semiconductor, Japan Customer Focus Center 4 32 Nishi Gotanda, Shinagawa ku, Tokyo, Japan 4 3 Phone: r4525@onsemi.com ON Semiconductor Website: For additional information, please contact your local Sales Representative. 2 MC452B/D
MARKING DIAGRAMS MAXIMUM RATINGS (Voltages Referenced to V SS ) (Note 1.) ORDERING INFORMATION PDIP 14 P SUFFIX CASE 646
The MC14106B hex Schmitt Trigger is constructed with MOS P channel and N channel enhancement mode devices in a single monolithic structure. These devices find primary use where low power dissipation and/or
More informationMC14536B. MARKING DIAGRAMS 16. MAXIMUM RATINGS (Voltages Referenced to V SS ) (Note 2.) ORDERING INFORMATION
The MC14536B programmable timer is a 24 stage binary ripple counter with 16 stages selectable by a binary code. Provisions for an on chip RC oscillator or an external clock are provided. An on chip monostable
More informationMC14066BF. MARKING DIAGRAMS. MAXIMUM RATINGS (Voltages Referenced to V SS ) (Note 2.) ORDERING INFORMATION PDIP 14 P SUFFIX CASE 646
The MC14066B consists of four independent switches capable of controlling either digital or analog signals. This quad bilateral switch is useful in signal gating, chopper, modulator, demodulator and CMOS
More informationMARKING DIAGRAMS 16 MAXIMUM RATINGS (Voltages Referenced to V SS ) (Note 1.) ORDERING INFORMATION PDIP 16 P SUFFIX CASE 648
查询 CD4553 供应商 The MC14553B 3 digit BCD counter coists of 3 negative edge triggered BCD counters that are cascaded synchronously. A quad latch at the output of each counter permits storage of any given
More informationMC14538B. MARKING DIAGRAMS. MAXIMUM RATINGS (Voltages Referenced to V SS ) (Note 2.) ORDERING INFORMATION
The MC14538B is a dual, retriggerable, resettable monostable multivibrator. It may be triggered from either edge of an input pulse, and produces an accurate output pulse over a wide range of widths, the
More informationMC14001B Series. B Suffix Series CMOS Gates MC14001B, MC14011B, MC14023B, MC14025B, MC14071B, MC14073B, MC14081B, MC14082B
MC4B Series B Suffix Series CMOS Gates MC4B, MC4B, MC4B, MC4B, MC4B, MC4B, MC4B, MC4B The B Series logic gates are constructed with P and N channel enhancement mode devices in a single monolithic structure
More informationMARKING DIAGRAMS MAXIMUM RATINGS (Note 1.) ORDERING INFORMATION PDIP 16 P SUFFIX CASE 648 MC140xxBCP AWLYYWW
The MC14051B, MC14052B, and MC14053B analog multiplexers are digitally controlled analog switches. The MC14051B effectively implements an SP8T solid state switch, the MC14052B a DP4T, and the MC14053B
More informationMC14040B. MARKING DIAGRAMS. MAXIMUM RATINGS (Voltages Referenced to VSS) (Note 2.) ORDERING INFORMATION PDIP 16 P SUFFIX CASE 648
The MC14040B 12 stage binary counter is cotructed with MOS P channel and N channel enhancement mode devices in a single monolithic structure. This part is designed with an input wave shaping circuit and
More informationMC33064DM 5 UNDERVOLTAGE SENSING CIRCUIT
The MC34064 is an undervoltage sensing circuit specifically designed for use as a reset controller in microprocessor-based systems. It offers the designer an economical solution for low voltage detection
More informationP D P D mw mw/ C Watts mw/ C T J, T stg 55 to +150 C (1) 200 C/W. Characteristic Symbol Min Typ Max Unit.
NPN Silicon ON Semiconductor Preferred Device MAXIMUM RATINGS Rating Symbol Value Unit Collector Emitter Voltage V CEO 45 Vdc Collector Base Voltage V CBO 45 Vdc Emitter Base Voltage V EBO 6.5 Vdc Collector
More information50 AMPERE COMPLEMENTARY SILICON POWER TRANSISTORS VOLTS 300 WATTS MAXIMUM RATINGS (1) THERMAL CHARACTERISTICS (1) Figure 1.
... designed for use in high power amplifier and switching circuit applications. High Current Capability I C Continuous = 50 Amperes. DC Current Gain h FE = 15 60 @ I C = 25 Adc Low Collector Emitter Saturation
More informationMARKING DIAGRAMS PIN CONNECTIONS ORDERING INFORMATION MC3x58P1 AWL YYWW PDIP 8 P1 SUFFIX CASE 626 SO 8 D SUFFIX CASE 751 3x58 ALYW
Utilizing the circuit designs perfected for the quad operational amplifiers, these dual operational amplifiers feature: low power drain, a common mode input voltage range extending to ground/v EE, and
More informationBC546, B BC547, A, B, C BC548, A, B, C
NPN Silicon MAXIMUM RATINGS Rating Symbol BC546 BC547 Unit Collector Emitter oltage CEO 65 45 30 dc Collector Base oltage CBO 80 50 30 dc Emitter Base oltage EBO 6.0 dc Collector Current Continuous I C
More information25 AMPERE COMPLEMENTARY SILICON POWER TRANSISTORS VOLTS 200 WATTS MAXIMUM RATINGS (1) THERMAL CHARACTERISTICS
... designed for general purpose power amplifier and switching applications. Low Collector Emitter Saturation Voltage V CE(sat) = 1.0 Vdc, (max) at I C = 15 Adc Low Leakage Current I CEX = 1.0 madc (max)
More informationN Channel Depletion MAXIMUM RATINGS. ELECTRICAL CHARACTERISTICS (T A = 25 C unless otherwise noted) OFF CHARACTERISTICS ON CHARACTERISTICS
N Channel Depletion MAXIMUM RATINGS Rating Symbol Value Unit Drain Source Voltage V DS 25 Vdc Drain Gate Voltage V DG 25 Vdc Gate Source Voltage V GS 25 Vdc Gate Current I G 10 madc Total Device Dissipation
More informationULTRAFAST RECTIFIERS 8.0 AMPERES VOLTS
Preferred Devices... designed for use in switching power supplies, inverters and as free wheeling diodes, these state of the art devices have the following features: Ultrafast 25, 50 and 75 Nanosecond
More informationDPAK Surface Mount Package
MBRD620CT, MBRD640CT and MBRD660CT are Preferred Devices DPAK Surface Mount Package...in switching power supplies, inverters and as free wheeling diodes, these state of the art devices have the following
More informationDARLINGTON 10 AMPERE COMPLEMENTARY SILICON POWER TRANSISTORS VOLTS 70 WATTS MAXIMUM RATINGS THERMAL CHARACTERISTICS. Collector Emitter Voltage
...designed for general purpose and low speed switching applications. High DC Current Gain h FE = 2500 (typ.) at I C = 4.0 Collector Emitter Sustaining Voltage at 100 madc V CEO(sus) = 80 Vdc (min.) BDX33B,
More informationTIP120, TIP121, TIP122,
... designed for general purpose amplifier and low speed switching applications. High DC Current Gain h FE = 2500 (Typ) @ I C = 4.0 Adc Collector Emitter Sustaining Voltage @ 100 madc V CEO(sus) = 60 Vdc
More information30 AMPERE POWER TRANSISTOR NPN SILICON 100 VOLTS 200 WATTS MAXIMUM RATINGS THERMAL CHARACTERISTICS. Figure 1. Power Temperature Derating Curve
... for use as an output device in complementary audio amplifiers to 100 Watts music power per channel. High DC Current Gain h FE = 25 100 @ I C = 7.5 A Excellent Safe Operating Area Complement to the
More information2N3055A MJ AMPERE COMPLEMENTARY SILICON POWER TRANSISTORS 60, 120 VOLTS 115, 180 WATTS *MAXIMUM RATINGS THERMAL CHARACTERISTICS
... PowerBase complementary transistors designed for high power audio, stepping motor and other linear applications. These devices can also be used in power switching circuits such as relay or solenoid
More informationMC14001B Series. B Suffix Series CMOS Gates MC14001B, MC14011B, MC14023B, MC14025B, MC14071B, MC14073B, MC14081B, MC14082B
MC4B Series BSuffix Series CMOS Gates MC4B, MC4B, MC4B, MC4B, MC4B, MC4B, MC4B, MC4B The B Series logic gates are constructed with P and N channel enhancement mode devices in a single monolithic structure
More information2N3771, 2N and 30 AMPERE POWER TRANSISTORS NPN SILICON 40 and 60 VOLTS 150 WATTS *MAXIMUM RATINGS THERMAL CHARACTERISTICS
... designed for linear amplifiers, series pass regulators, and inductive switching applications. Forward Biased Second Breakdown Current Capability I S/b = 3.75 Adc @ V CE = 40 2N3771 = 2.5 Adc @ V CE
More informationLOW POWER SCHOTTKY. GUARANTEED OPERATING RANGES ORDERING INFORMATION
The SN74LS64 is a high speed 8-Bit Serial-In Parallel-Out Shift Register. Serial data is entered through a 2-Input AN gate synchronous with the LOW to HIGH transition of the clock. The device features
More information30 AMPERE POWER TRANSISTOR PNP SILICON 100 VOLTS 200 WATTS MAXIMUM RATINGS MAXIMUM RATINGS. Figure 1. Power Temperature Derating Curve
... for use as an output device in complementary audio amplifiers to 100 Watts music power per channel. High DC Current Gain h FE = 25 100 @ I C = 7.5 A Excellent Safe Operating Area Complement to the
More informationPIN CONNECTIONS Representative Schematic Diagram
The MC34063A Series is a monolithic control circuit containing the primary functions required for DC to DC converters. These devices consist of an internal temperature compensated reference, comparator,
More informationMARKING DIAGRAMS LOGIC DIAGRAM ORDERING INFORMATION DIP PIN ASSIGNMENT CDIP 16 L SUFFIX CASE 620 MC10124L AWLYYWW
The MC024 is a quad translator for interfacing data and control signals between a saturated logic section and the MECL section of digital systems. The MC024 has TTL compatible inputs, and MECL complementary
More informationThe MC10109 is a dual 4 5 input OR/NOR gate. P D = 30 mw typ/gate (No Load) t pd = 2.0 ns typ t r, t f = 2.0 ns typ (20% 80%)
The MC10109 is a dual 5 input OR/NOR gate. P D = 0 mw typ/gate (No Load) t pd =.0 ns typ t r, t f =.0 ns typ (0% 0%) LOGIC DIAGRAM MARKING DIAGRAMS CDIP 16 L SUFFIX CASE 60 PDIP 16 P SUFFIX CASE 6 PLCC
More informationMJ10015 MJ AMPERE NPN SILICON POWER DARLINGTON TRANSISTORS 400 AND 500 VOLTS 250 WATTS MAXIMUM RATINGS THERMAL CHARACTERISTICS
The MJ10015 and MJ10016 Darlington transistors are designed for high voltage, high speed, power switching in inductive circuits where fall time is critical. They are particularly suited for line operated
More informationLOGIC DIAGRAM AND PINOUT ASSIGNMENT V CC TTL PECL 3. MARKING DIAGRAMS* ORDERING INFORMATION PIN DESCRIPTION HLT20 ALYW KLT20 ALYW
The MC0ELT/00ELT20 is a TTL to differential PECL translator. Because PECL (Positive ECL) levels are used, only +5 V and ground are required. The small outline -lead package and the single gate of the ELT20
More informationLOW POWER SCHOTTKY. MARKING DIAGRAMS GUARANTEED OPERATING RANGES
The SN74LS373 consists of eight latches with 3-state outputs for bus organized system applications. The flip-flops appear transparent to the data (data changes asynchronously) when Latch Enable (LE) is
More informationORDERING INFORMATION Figure 1. Pinout: 20 Lead Packages Conductors (Top View) PIN ASSIGNMENT
The MC74AC273/74ACT273 has eight edge-triggered D type flip flops with individual D inputs and Q outputs. The common buffered Clock (CP) and Master Reset (MR) inputs load and reset (clear) all flip flops
More informationORDERING INFORMATION Figure 1. Pinout: 20 Lead Packages Conductors (Top View) PIN ASSIGNMENT
The MC74AC574/74ACT574 is a high speed, low power octal flip flop with a buffered common Clock (CP) and a buffered common Output Enable (OE). The information presented to the D inputs is stored in the
More informationMC100EPT22/D. MARKING DIAGRAMS* ORDERING INFORMATION SO 8 D SUFFIX CASE 751 KPT22 ALYW TSSOP 8 DT SUFFIX CASE 948R KA22 ALYW
The MC00EPT22 is a dual LVTTL/LVCMOS to differential LVPECL translator. Because LVPECL (Positive ECL) levels are used only +3.3 V and ground are required. The small outline lead package and the single
More information500 mw SOD 123 Surface Mount
500 mw SOD 123 Surface Mount Three complete series of Zener diodes are offered in the convenient, surface mount plastic SOD 123 package. These devices provide a convenient alternative to the leadless 34
More informationMARKING DIAGRAMS LOGIC DIAGRAM ORDERING INFORMATION DIP PIN ASSIGNMENT CDIP 16 L SUFFIX CASE 620 MC10216L AWLYYWW
The MC1016 is a high speed triple differential amplifier designed for use in sensing differential signals over long lines. The base bias supply (V BB ) is made available at pin 11 to make the device useful
More informationGENERAL PURPOSE TRANSISTOR ARRAY
The MC3346 is designed for general purpose, low power applications for consumer and industrial designs. Guaranteed BaseEmitter Voltage Matching Operating Current Range Specified: 10 µa to 10 ma Five General
More informationMARKING DIAGRAMS Figure 1. Logic Diagram ORDERING INFORMATION Figure 2. Dip Pin Assignment CDIP 16 L SUFFIX CASE 620A
The MC0H6 is a functional/pinout duplication of the MC06, with 00% improvement in propagation delay and no increase in power supply current. Propagation Delay,.0 ns Typical Power Dissipation 85 mw Typ/Pkg
More informationDUAL TIMING CIRCUIT SEMICONDUCTOR TECHNICAL DATA PIN CONNECTIONS ORDERING INFORMATION. Figure Second Solid State Time Delay Relay Circuit
The MC3456 dual timing circuit is a highly stable controller capable of producing accurate time delays, or oscillation. Additional terminals are provided for triggering or resetting if desired. In the
More informationPERIPHERAL DRIVER ARRAYS
The seven NPN Darlington connected transistors in these arrays are well suited for driving lamps, relays, or printer hammers in a variety of industrial and consumer applications. Their high breakdown voltage
More informationMC14001B Series. B-Suffix Series CMOS Gates MC14001B, MC14011B, MC14023B, MC14025B, MC14071B, MC14073B, MC14081B, MC14082B
MC4B Series B-Suffix Series CMOS Gates MC4B, MC4B, MC4B, MC4B, MC4B, MC4B, MC4B, MC4B The B Series logic gates are constructed with P and N channel enhancement mode devices in a single monolithic structure
More informationMBRB20200CT. Dual Schottky Rectifier SCHOTTKY BARRIER RECTIFIER 20 AMPERES 200 VOLTS
Preferred Device Dual Schottky Rectifier... using Schottky Barrier technology with a platinum barrier metal. This state of the art device is designed for use in high frequency switching power supplies
More informationTIMING CIRCUIT SEMICONDUCTOR TECHNICAL DATA ORDERING INFORMATION. Figure Second Solid State Time Delay Relay Circuit
The MC1455 monolithic timing circuit is a highly stable controller capable of producing accurate time delays or oscillation. Additional terminals are provided for triggering or resetting if desired. In
More informationPIN CONNECTIONS
The NCP4421/4422 are high current buffer/drivers capable of driving large MOSFETs and IGBTs. They are essentially immune to any form of upset except direct overvoltage or over dissipation they cannot be
More informationPIN CONNECTIONS ORDERING INFORMATION FUNCTIONAL TABLE
The MC12026 is a high frequency, low voltage dual modulus prescaler used in phase locked loop (PLL) applications. The MC12026A can be used with CMOS synthesizers requiring positive edges to trigger internal
More informationAPPLICATION NOTE. where Vundershoot = (Vref lower) Gnd. Hence the retrigger time is given by:
Prepared by: Douglas M. Buzard, Rodolfo E. Soto Introduction The MC74HC4538A is a monostable multivibrator commonly used as a one shot, or in applications that require a pulse width of reliable dimensions.
More informationTMOS E FET. Power Field Effect Transistor MTP8N50E. N Channel Enhancement Mode Silicon Gate
TMOS E FET. Power Field Effect Transistor N Channel Enhancement Mode Silicon Gate MTP8N5E This high voltage MOSFET uses an advanced termination scheme to provide enhanced voltage blocking capability without
More informationLOW POWER SCHOTTKY. GUARANTEED OPERATING RANGES ORDERING INFORMATION
The SN74LS298 is a Quad 2-Port Register. It is the logical equivalent of a quad 2-input multiplexer followed by a quad 4-bit edge-triggered register. A Common Select input selects between two 4-bit input
More informationMARKING DIAGRAMS Split Supplies Single Supply PIN CONNECTIONS MAXIMUM RATINGS ORDERING INFORMATION SO 14 D SUFFIX CASE 751A
The MC3403 is a low cost, quad operational amplifier with true differential inputs. The device has electrical characteristics similar to the popular MC1741C. However, the MC3403 has several distinct advantages
More informationOutputs Source/Sink 24 ma ACT157 Has TTL Compatible Inputs. Figure 1. Pinout: 16 Lead Packages Conductors (Top View) PIN NAME
The MC74AC157/74ACT157 is a high speed quad 2 input multiplexer. Four bits of data from two sources can be selected using the common Select and Enable inputs. The four outputs present the selected data
More informationSilicon Bidirectional Thyristors
Preferred Device Silicon Bidirectional Thyristors Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required. Blocking Voltage to
More informationPOWER TRANSISTORS 5 AMPERES 1200 VOLTS 35 and 75 WATTS MAXIMUM RATINGS THERMAL CHARACTERISTICS. Symbol MJE18204 MJF18204 Unit
The MJE/MJF18204 have an application specific state of the art die dedicated to the electronic ballast ( light ballast ) and power supply applications. Improved Global Efficiency Due to Low Base Drive
More informationReverse Blocking Thyristors
Preferred Device Reverse Blocking Thyristors Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supply crowbar circuits. Glass Passivated Junctions
More informationMC14532B. 8-Bit Priority Encoder
MC4532B 8-Bit Priority Encoder The MC4532B is cotructed with complementary MOS (CMOS) enhancement mode devices. The primary function of a priority encoder is to provide a binary address for the active
More informationMARKING DIAGRAMS LOGIC DIAGRAM PIN ASSIGNMENT ORDERING INFORMATION FUNCTION TABLE DIP 14 N SUFFIX CASE 646 MC74HC4066AN AWLYYWW
High Performance Silicon Gate CMOS The MC74HC466A utilizes silicon gate CMOS technology to achieve fast propagation delays, low ON resistances, and low OFF channel leakage current. This bilateral switch/
More informationThis document, MC74HC4066/D has been canceled and replaced by MC74HC4066A/D LAN was sent 9/28/01
http://onsemi.com This document, MC74HC4066/D has been canceled and replaced by MC74HC4066A/D LAN was sent 9/28/01 High Performance Silicon Gate CMOS The MC54/74HC4066 utilizes silicon gate CMOS technology
More informationMARKING DIAGRAMS PIN CONNECTIONS ORDERING INFORMATION
The MC346/MC336 are universal voltage monitors intended for use in a wide variety of voltage sensing applications. These devices offer the circuit designer an economical solution for positive and negative
More informationMC14514B, MC14515B. 4-Bit Transparent Latch / 4-to-16 Line Decoder
MC14514B, MC145B 4-Bit Traparent Latch / 4-to-16 Line Decoder The MC14514B and MC145B are two output optio of a 4 to 16 line decoder with latched inputs. The MC14514B (output active high option) presents
More informationPNP Silicon Surface Mount Transistor with Monolithic Bias Resistor Network
Preferred Devices PNP Silicon Surface Mount Transistor with Monolithic Bias Resistor Network This new series of digital transistors is designed to replace a single device and its external resistor bias
More informationLOW DROPOUT DUAL VOLTAGE REGULATOR
The LM293 is a dual positive.0 low dropout voltage regulator, designed for standby power systems. The main output is capable of supplying 70 ma for microprocessor power, and can be turned on and off by
More informationMMBFJ309. N Channel MAXIMUM RATINGS THERMAL CHARACTERISTICS DEVICE MARKING. ELECTRICAL CHARACTERISTICS (T A = 25 C unless otherwise noted)
N Channel MAXIMUM RATINGS Rating Symbol Value Unit Drain Source Voltage V DS 25 Vdc Gate Source Voltage V GS 25 Vdc Gate Current I G 10 madc THERMAL CHARACTERISTICS Characteristic Symbol Max Unit Total
More informationMARKING DIAGRAMS ORDERING INFORMATION Figure 1. Representative Schematic Diagram (Each Amplifier) DUAL MC33078P
The MC33078/9 series is a family of high quality monolithic amplifiers employing Bipolar technology with innovative high performance concepts for quality audio and data signal processing applications.
More informationLOW POWER SCHOTTKY. GUARANTEED OPERATING RANGES ORDERING INFORMATION PLASTIC N SUFFIX CASE 646 SOIC D SUFFIX CASE 751A
These dc triggered multivibrators feature pulse width control by three methods. The basic pulse width is programmed by selection of external resistance and capacitance values. The LS122 has an internal
More informationHigh Performance Silicon Gate CMOS
High Performance Silicon Gate CMOS The MC74HC4316A utilizes silicon gate CMOS technology to achieve fast propagation delays, low ON resistances, and low OFF channel leakage current. This bilateral switch/multiplexer/
More informationReverse Blocking Thyristors
Preferred Device Reverse Blocking Thyristors Glassivated PNPN devices designed for high volume consumer applications such as temperature, light, and speed control; process and remote control, and warning
More informationMM74HC04 Hex Inverter
MM74HC04 Hex Inverter Features Typical propagation delay: 8ns Fan out of 10 LS-TTL loads Quiescent power consumption: 10µW maximum at room temperature Low input current: 1µA maximum General Description
More informationMARKING DIAGRAMS PIN CONNECTIONS ORDERING INFORMATION PDIP 8 N SUFFIX CASE 626 LM311D AWL YYWW SO 8 98 Units/Rail
The ability to operate from a single power supply of 5.0 V to 30 V or 15 V split supplies, as commonly used with operational amplifiers, makes the LM211/LM311 a truly versatile comparator. Moreover, the
More informationMARKING DIAGRAMS ORDERING INFORMATION DUAL MC33272AP AWL YYWW PDIP 8 P SUFFIX CASE 626 SO 8 D SUFFIX CASE ALYWA QUAD
The MC33272/74 series of monolithic operational amplifiers are quality fabricated with innovative Bipolar design concepts. This dual and quad operational amplifier series incorporates Bipolar inputs along
More informationSN74LS122, SN74LS123. Retriggerable Monostable Multivibrators LOW POWER SCHOTTKY
Retriggerable Monostable Multivibrators These dc triggered multivibrators feature pulse width control by three methods. The basic pulse width is programmed by selection of external resistance and capacitance
More informationPIN CONNECTIONS
Utilizing the circuit designs perfected for Quad Operational Amplifiers, these dual operational amplifiers feature low power drain, a common mode input voltage range extending to ground/v EE, and single
More informationMC3488A. Dual EIA 423/EIA 232D Line Driver
Dual EIA423/EIA232D Line Driver The MC34A dual is singleended line driver has been designed to satisfy the requirements of EIA standards EIA423 and EIA232D, as well as CCITT X.26, X.2 and Federal Standard
More informationMAXIMUM RATINGS (T A = +25 C, unless otherwise noted.) PIN CONNECTIONS
The LM324 series are low cost, quad operational amplifiers with true differential inputs. They have several distinct advantages over standard operational amplifier types in single supply applications.
More informationI E I EM 24 P D
NPN Bipolar Power Transistor For Switching Power Supply Applications The MJE13007 is designed for high voltage, high speed power switching inductive circuits where fall time is critical. It is particularly
More informationMM74HC14 Hex Inverting Schmitt Trigger
MM74HC14 Hex Inverting Schmitt Trigger Features Typical propagation delay: 13ns Wide power supply range: 2V 6V Low quiescent current: 20µA maximum (74HC Series) Low input current: 1µA maximum Fanout of
More informationMC14016B. Quad Analog Switch/ Quad Multiplexer
Quad Analog Switch/ Quad Multiplexer The MC406B quad bilateral switch is constructed with MOS Pchannel and Nchannel enhancement mode devices in a single monolithic structure. Each MC406B consists of four
More informationAN1404/D. ECLinPS Circuit Performance at Non-Standard V IH Levels APPLICATION NOTE
ECLinPS Circuit Performance at Non-Standard V IH Levels Prepared by Todd Pearson ECL Applications Engineering APPLICATION NOTE This application note explains the consequences of driving an ECLinPS device
More informationWatts T. W/ C Operating and Storage Junction. T J, T stg
The BUS98 and BUS98A transistors are designed for high voltage, high speed, power switching in inductive circuits where fall time is critical. They are particularly suited for line operated SWITCHMODE
More informationNPN MPS650 PNP MPS750 MAXIMUM RATINGS THERMAL CHARACTERISTICS. ELECTRICAL CHARACTERISTICS (TC = 25 C unless otherwise noted) OFF CHARACTERISTICS
MAXIMUM RATINGS Rating Symbol MPS650 MPS750 MPS651 MPS751 Collector Emitter Voltage VCE 40 60 Vdc Collector Base Voltage VCB 60 80 Vdc Emitter Base Voltage VEB 5.0 Vdc Collector Current Continuous IC 2.0
More information1 kv SWITCHMODE Series
1 kv SWITCHMODE Series These transistors are designed for high voltage, high speed, power switching in inductive circuits where fall time is critical. They are particularly suited for line operated SWITCHMODE
More informationPIN ASSIGNMENT B 1 18 C 2 17 f LT 3 16 g BI 4 a LE 5 14 b D 6 13 c A 7 12 d RBI e RBO e f d g a c b DISPLAY TRUTH TABLE Input
BCDToSeven Segment Latch/Decoder/Driver CMOS MSI (LowPower Complementary MOS) The MC14513B BCDtoseven segment latch/decoder/driver is cotructed with complementary MOS (CMOS) enhancement mode devices and
More informationUnidirectional*
Unidirectional* Mosorb devices are designed to protect voltage sensitive components from high voltage, high energy transients. They have excellent clamping capability, high surge capability, low zener
More informationMC14066B. Quad Analog Switch/Quad Multiplexer
Quad Analog Switch/Quad Multiplexer The MC4066B consists of four independent switches capable of controlling either digital or analog signals. This quad bilateral switch is useful in signal gating, chopper,
More informationNPN Silicon ON Semiconductor Preferred Device
NPN Silicon ON Semiconductor Preferred Device MAXIMUM RATINGS Rating Symbol Value Unit Collector Emitter Voltage VCEO 40 Vdc Collector Base Voltage VCBO 60 Vdc Emitter Base Voltage VEBO 6.0 Vdc Collector
More informationN Channel Depletion MAXIMUM RATINGS. ELECTRICAL CHARACTERISTICS (TA = 25 C unless otherwise noted) OFF CHARACTERISTICS ON CHARACTERISTICS
N Channel Depletion MAXIMUM RATINGS Rating Symbol Value Unit Drain Source Voltage VDS 25 Vdc Drain Gate Voltage VDG 25 Vdc Gate Source Voltage VGS 25 Vdc Forward Gate Current IGF 10 madc Total Device Dissipation
More informationORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 11 of this data sheet.
The MC3320/2/4 family of operational amplifiers provide railtorail operation on both the input and output. The inputs can be driven as high as 200 mv beyond the supply rails without phase reversal on the
More informationPIN CONNECTIONS ORDERING INFORMATION PIN CONNECTIONS P SUFFIX PLASTIC PACKAGE CASE 626 D SUFFIX PLASTIC PACKAGE CASE 751 (SO 8) Inputs P SUFFIX
Quality bipolar fabrication with innovative design concepts are employed for the MC33181/2/4, MC34181/2/4 series of monolithic operational amplifiers. This JFET input series of operational amplifiers operates
More informationN Channel Depletion MAXIMUM RATINGS. ELECTRICAL CHARACTERISTICS (TA = 25 C unless otherwise noted) OFF CHARACTERISTICS ON CHARACTERISTICS
N Channel Depletion MAXIMUM RATINGS Rating Symbol Value Unit Drain Source Voltage VDS 25 Vdc Drain Gate Voltage VDG 25 Vdc Gate Source Voltage VGS 25 Vdc Gate Current IG 10 madc Total Device Dissipation
More information4 AMPERE POWER TRANSISTORS COMPLEMENTARY SILICON 60 VOLTS 15 WATTS MAXIMUM RATINGS THERMAL CHARACTERISTICS. Figure 1. Power Derating BD787
... designed for lower power audio amplifier and low current, high speed switching applications. Low Collector Emitter Sustaining Voltage VCEO(sus) 60 Vdc (Min) BD787, BD788 High Current Gain Bandwidth
More informationCMOS Micro-Power Comparator plus Voltage Follower
Freescale Semiconductor Technical Data Rev 2, 05/2005 CMOS Micro-Power Comparator plus Voltage Follower The is an analog building block consisting of a very-high input impedance comparator. The voltage
More information1 AMPERE GENERAL PURPOSE POWER TRANSISTORS VOLTS 30 WATTS *MAXIMUM RATINGS THERMAL CHARACTERISTICS (2)
...designed for driver circuits, switching, and amplifier applications. These high performance plastic devices feature: Low Saturation Voltage VCE(sat) = 0.6 Vdc (Max) @ IC = 1.0 Amp Excellent Power Dissipation
More informationLOW POWER JFET INPUT OPERATIONAL AMPLIFIERS
These JFET input operational amplifiers are designed for low power applications. They feature high input impedance, low input bias current and low input offset current. Advanced design techniques allow
More informationP2I2305NZ. 3.3V 1:5 Clock Buffer
3.3V :5 Clock Buffer Functional Description P2I2305NZ is a low cost high speed buffer designed to accept one clock input and distribute up to five clocks in mobile PC systems and desktop PC systems. The
More informationCS PIN CONNECTIONS AND MARKING DIAGRAM ORDERING INFORMATION SO 14 D SUFFIX CASE 751A V CC. = Assembly Location
The CS3361 integral alternator regulator integrated circuit provides the voltage regulation for automotive, 3 phase alternators. It drives an external logic level N channel enhancement power FET for control
More informationPCS2I2309NZ. 3.3 V 1:9 Clock Buffer
. V 1:9 Clock Buffer Functional Description PCS2I209NZ is a low cost high speed buffer designed to accept one clock input and distribute up to nine clocks in mobile PC systems and desktop PC systems. The
More information2N5194 2N for use in power amplifier and switching circuits, excellent safe area limits. Complement to NPN 2N5191, 2N5192
... for use in power amplifier and switching circuits, excellent safe area limits. Complement to NPN 2N5191, 2N5192 ÎÎ *MAXIMUM RATINGS ÎÎ Rating ÎÎ Symbol Î 2N5194 Î Unit ÎÎ Collector Emitter Voltage
More informationHigh Performance Silicon Gate CMOS
High Performance Silicon Gate CMOS The MC74CA is identical in pinout to the standard CMOS MC. The device inputs are compatible with standard CMOS outputs; with pullup resistors, they are compatible with
More informationNC7S14 TinyLogic HS Inverter with Schmitt Trigger Input
NC7S14 TinyLogic HS Inverter with Schmitt Trigger Input General Description The NC7S14 is a single high performance CMOS Inverter with Schmitt Trigger input. The circuit design provides hysteresis between
More informationMJ16110 MJW SWITCHMODE Bridge Series
SWITCHMODE Bridge Series... specifically designed for use in half bridge and full bridge off line converters. Excellent Dynamic Saturation Characteristics Rugged RBSOA Capability Collector Emitter Sustaining
More informationMC14066B. Quad Analog Switch/Quad Multiplexer
Quad Analog Switch/Quad Multiplexer The MC4066B consists of four independent switches capable of controlling either digital or analog signals. This quad bilateral switch is useful in signal gating, chopper,
More informationMC34085BP HIGH PERFORMANCE JFET INPUT OPERATIONAL AMPLIFIERS
These devices are a new generation of high speed JFET input monolithic operational amplifiers. Innovative design concepts along with JFET technology provide wide gain bandwidth product and high slew rate.
More information