COURSE OUTLINE. School of Engineering Technology & Applied Science. Advanced Manufacturing & Automation Technology (AMAT)

Transcription

1 COURSE OUTLINE SCHOOL: DEPARTMENT: PROGRAM: COURSE TITLE: COURSE CODE: School of Engineering Technology & Applied Science Advanced Manufacturing & Automation Technology (AMAT) Automation & Robotics Technology/Technician AutoCAD 1 & Blueprint Reading ROBO-115 TOTAL COURSE HOURS: 75 (2-hr lecture/wk + 3-hr lab/wk = 5-hrs/wk) (5-hrs/wk x 15 wks = 75-hrs) PRE-REQUISITES/CO-REQUISITES: N/A COURSE ELIGIBILITY FOR PRIOR LEARNING ASSESSMENT AND RECOGNITION (PLAR): Yes ORIGINATED BY: Enzo Bevilacqua ( ) REVISED BY: Enzo Bevilacqua REVISION DATE: APPROVED BY: Chairperson/Dean ACADEMIC YEAR: NOTE: Students should keep all course outlines for each course taken at Centennial College. These may be used to apply for transfer of credit to other educational institutions. A fee may be charged for additional or replacement copies. SETAS: THIS COURSE ADHERES TO ALL COLLEGE POLICIES (See College Calendar) Page 1

2 COURSE DESCRIPTION: The dual purpose of this course is to allow the student to become familiarized with the basic technical drawing elements of mechanical engineering graphics as well as the concepts and features of the AutoCAD computer-assisted-drafting program. The course will discuss the principles of graphic communication, projections and the industrial standards utilized in typical engineering drawings. The course will also simultaneously discuss the implementation of the drafting theory by using the computer as an electronic drafting board and design tool. Weekly instruction will be given in two parts: a two hour theory class and a three hour lab session. Theory sessions, which will be held in classrooms, will involve a lecture portion as well as individual manual sketching. The lab sessions, which will be held in one of the AutoCAD equipped computer labs, will consist of approximately ½ -hour theory (software) and 2½-hours of hands-on lab practice. In most sessions the student will be introduced to new drafting principles and/or the necessary CAD commands, operations and techniques to implement the theory. A series of specifically designed illustrative exercises, assigned during the course, will provide the student with the necessary practice for skill development. COURSE LEARNING OUTCOMES: Upon successful completion, students will have reliably demonstrated the ability to: Comprehend the fundamental graphic language concepts of mechanical engineering drafting (CSA standards). Effectively use the fundamental program commands found in the AutoCAD software. Employ the AutoCAD software to prepare precise and fully annotated multi-view two-dimensional orthographic engineering drawings & graphics, including full and partial sections, all of which properly adhere to CSA standards and meet acceptable industry standards. Employ the AutoCAD software to prepare precise and fully annotated electronic schematics as per IEEE standards. ESSENTIAL EMPLOYABILITY SKILLS (EES): This course supports the students ability to: Communicate clearly, concisely and correctly in the written, spoken and visual form that fulfills the purpose and meets the needs of audiences. Reframe information, ideas and concepts using the narrative, visual, numerical and symbolic representations, which demonstrate understanding. Use a variety of computer hardware and software, and other technological tools appropriate and necessary to the performance of tasks. Create innovative strategies and/or products that meet identified needs. Manage the use of time and other resources to attain personal and/or project-related goals. Take responsibility for his or her own actions and decisions. PRIOR LEARNING ASSESSMENT & RECOGNITION PROCESS (ES): This course is eligible for PLAR through the Registrar and SETAS offices. Assessment of portfolio and/or testing may be discussed with faculty. SETAS: THIS COURSE ADHERES TO ALL COLLEGE POLICIES (See College Calendar) Page 2

3 EVALUATION & GRADING SYSTEM: Evaluation Policies: Attendance to all classes is mandatory. Students are expected to punctually attend all lectures and to complete all drawing assignments in the allotted time specified for each*. Failure to attend 20% or more may result in the student not being permitted to write the final exams. If one of the term tests cannot be written because of documented medical or compassionate reasons, the weight of the final exam will be proportionally increased. Note that a mark of zero will be recorded in cases where no reason, acceptable to the professor, is provided. Students must write and pass the final exams in order to pass the course regardless if sufficient marks have already been obtained in the semester. (Note: any student, who is otherwise passing the course but will fail as a result of failing the final examination, will be permitted to write one supplemental examination. This supplemental examination will normally occur within approximately two weeks after the final grades are posted.) This course does not prescribe to re-writes except in such cases as discussed in the Student Accommodation section. *Note, unless otherwise specified, all drawing assignments are generally due at the end of class or by the start of the next session. Late drawing assignments will not be accepted or marked. Assignments will be marked in the following manner: Mark Assigned: Rationalization: Relative Valuation: OK N-OK (Not-OK) Ø Drawing is correct and complete. (Drawing may contain up to 3 minor errors.) Drawing is mostly correct but contains more than 3 minor errors or 1 major error. Drawing has more than 5 minor errors, 2 or more major errors or was submitted late. 1 point ½ point 0 points IMPORTANT NOTE: Plagiarism and copying will not be tolerated. All copied work (assignments/drawings/tests), including the original, will receive a zero grade. No exceptions! (Refer to the College s Plagiarism Policy on Page 5.) Evaluation and Grade Allocation: BPR Theory AutoCAD TOTAL Portfolios: In-class CAD drawings & assignments* 5% 10% 15% Mid-Term Tests: 10% 20% 30% Final Tests: 20% 35% 55% 100% * NOTE: Unless otherwise specified, all drawing assignments are due by the end of class or by the start of the next session. SETAS: THIS COURSE ADHERES TO ALL COLLEGE POLICIES (See College Calendar) Page 3

4 STUDENT ACCOMMODATION: All students have the right to study in an environment that is free from discrimination and/or harassment. It is College Policy to provide accommodation based on grounds defined in the Ontario Human Rights Code. Accommodation may include changes or modifications to standard practices. Students with disabilities who require academic accommodations must register with the Centre for Student with Disabilities. Please see the Centre for Students with Disabilities for details. Students requiring accommodation based on human rights grounds should talk with their professors as early as possible. Details are available on the Centennial College website ( ). If students are unable to write an examination due to a medical problem or unforeseen family problems, they should immediately contact their professor or program Chair for advice. In exceptional and well documented circumstances (e.g. unexpected family problems, serious illness, or death of a close family member), students should be able to write a make-up examination to replace an examination missed. TEXTS AND OTHER INSTRUCTIONAL/LEARNING MATERIALS: Required Course Text: Introduction to AutoCAD Exercise Manual By E. Bevilacqua, BeviTEK Publications, ISBN: Reference Texts: Technical Drawing General Principles Canadian Standards Association (latest edition preferable) Interpreting Engineering Drawings, Fifth Canadian Edition (or equivalent) by Cecil Jensen & Jay HelselPublisher: Thomson/Nelson, ISBN-13: AutoCAD 2008: A Problem Solving Approach by Sham Tickoo, AutoDesk Press, ISBN-13: Other Instructional/ Learning Materials: No drafting theory textbook required. Weekly notes will be posted on the college network and are to be downloaded and printed by the student prior to each theory class. USB flash memory device [IMPORTANT] ¼ Square paper Drafting Pencil & Eraser Ruler (inch & mm); Protractor; Compasses; 45 & 30 Set Squares (optional) USE OF DICTIONARIES: Dictionaries are not permitted during tests or exams in this course. SETAS: THIS COURSE ADHERES TO ALL COLLEGE POLICIES (See College Calendar) Page 4

5 POLICY STATEMENTS College Policies The following statements are selected from Centennial College policies approved by the Board of Governors. Student Responsibilities Students are expected to know the contents of the course outline and to discuss with the professor any areas where clarification is required. Students should keep all course outlines for each course taken at Centennial College. These may be used to apply for transfer of credit to other educational institutions. A fee may be charged for additional or replacement copies. Other Policies Students should familiarize themselves with all College Policies that cover students rights, responsibilities, and the Academic Appeal process. For further information, consult the Academic Matters Section in the full-time and Continuing Education calendars. The Academic Appeal Application form is available from any Enrolment Services Office. Proof of Student Status Students must produce official photo identification at any time during the semester when requested to do so by any professor. (The official piece is the Centennial Student Card.) Continuing Education students do not have Centennial Student Cards, and so they may use other forms of photo identification, such as a driver s license, health card, or other government-issued photo identification. Final Examinations When writing a test or examination, students must put their official photo-id cards in full view for review by the invigilator. Students who do not have official photo-id will be permitted to write the examination with a substitute photo-id, but they will be required to produce photo-id at the program or department office within 24 hours or the next business day following the examination, or else the examination results will be void. More Final Examination Policies are available at Cheating Any student who, in an examination, copies from the work of another person in the examination room, or who uses notes or other memory aids without the permission of the invigilator, or who permits such copying, or supplies such notes or memory aids to another, breaches proper conduct and is liable to a sanction under this Academic Honesty and Plagiarism Policy and Procedures. This type of action may also be subject to an academic sanction such as a failing grade. Plagiarism Any Student who, in an assignment, submits work that is substantially copied from the work of another person, without attribution, and represents that such work is his or her own, breaches proper conduct and is liable to a sanction under this Policy. This type of action may also be subject to an academic sanction such as a failing grade. Academic Progression Policy for Diploma and Certificate Programs College Academic Standings will be applied. Please see Academic Policies and Procedures, Full-Time Calendar. Faculty Consultation Professors are available to see students outside of class time. Students can contact professors via voice mail, , or through their program or department office. Information regarding how to contact teachers will be provided at the beginning of the course and is also available in the program or department office. Human Rights Statement It is the policy of the College that all programs will strive for a learning, teaching, and working environment that promotes inclusion, understanding, and respect for all students and employees, consistent with the Ontario Human Rights Code and Centennial College's Statement of Diversity. SETAS: THIS COURSE ADHERES TO ALL COLLEGE POLICIES (See College Calendar) Page 5

6 Course Title: AutoCAD 1 & BPR CENTENNIAL COLLEGE Course Code: ROBO-115 Wk Topic/Content* Instructional Objectives Tests and Assignments 1 Introduction to the course. Peruse course outline. Discussion of fundamental course objectives. Orthographic projection Theory: Alphabet of lines Unit #1 Basic orthographic/isometric projection relationships - 3 rd angle. 2 3 System fundamentals Basic drawing functions Units & Dimensioning concepts Additional drawing commands Non-linear drawing elements Modify menu items Adding dimensions Non-visible edges CAD: Hardware/software configuration and details. Basic workstation and system overview - operating concepts and procedures. Starting a drawing sheets sizes, standard drawing frame templates. Initial software commands, the DRAW menu, linetype, color & lineweight, grid & grid snap, drawing by vector input, ZOOM. ERASE and titleblock editing. Theory: Working drawings. Units & imperial/metric dimensioning concepts. CAD: Drawing by coordinate entry. Use of the RECTANGLE, POLYGON, CIRCLE, and ARC commands. Use of the FILLET and CHAMFER commands. Linear, radial and angular dimensioning. Theory: Hidden lines and Inclined surfaces. Exercise #1 - Abutment Block Exercise #2 - Adjustable Baseplate Unit #2 & 17 Exercise #3 Punch Plate (Co-ordinate Entry & Dimensioning) Unit #3, 4 & Using construction line layout techniques Curved features Construction lines (cont d) Sectioning principles CAD: Discussion of drawing layout and use of the construction line commands. Drawing cleanup with the TRIM command. Discussion of drawing scale. Modifying standard A-size template for a drawing of scale other than 1:1. Working with a metric environment. Theory: Circular features. CAD: Layout & creation of standard 3-view orthographic projection drawings. Theory: Purpose and types of sections. Creating sectional views. Exercise #4 - Tapering Plate Exercise #5 Fork Shifter Exercise #6 - Tucker Gasket Unit #5 Exercise #24 - Ortho Blocks Unit #8 7 8 Ortho views & layout Sectioning principles (cont d) Hatching Mid-Term Tests CAD: More complex 3-view orthographic drawing. Theory: Additional sectioning concepts. Revolved and removed sections.broken out and partial sections. Webs, ribs and spokes in section. CAD: - Additional drawing commands: ELLIPSE and SPLINE. Discussion on the concept and use of hatching for sectioning. Theory Test: Multiple choice & sketching CAD Test: Replicate a fully dimensioned 2-view orthographic drawing w/ sectional view. Exercise #25 - Clutch Bracket Unit #16 & 28 Exercise #7 - Drive Assembly Exercise #27 - Taper Collar Theory Test = 10% (1 Hr) CAD Test = 20% (2 Hrs) Continued THIS COURSE ADHERES TO ALL COLLEGE POLICIES (See College Calendar) Page 6

7 Course Title: AutoCAD 1 & BPR CENTENNIAL COLLEGE Course Code: ROBO-115 Wk Topic/Content* Instructional Objectives Tests and Assignments Auxiliary views Theory: Test results - analysis Unit #18 9 Problems of foreshortened views. Creating auxiliary views. Hatching & Sectioning (cont d) Further useage of hatching for offset sectioning. Exercise #29 Bearing Support Fasteners Theory: Threaded fasteners - concepts and representation. Unit #15, Representation of gears and cams Unit #31 Miscellaneous topics (General Assembly drawings, Bill Of Materials & detail drawings) Drawing element grouping Repositioning and replication Text IEEE standards Mirroring and Arrays Schematics (cont d) PCB design Blocks Additional materials & review Blocks (cont d) Final Theory Test CAD: Drawing objects composed of many separate elements & using the GROUP function in order to manipulate them as whole. Use of the MOVE and COPY commands. Discussion of text and font concepts and their uses. Using leader lines. Theory: IEEE symbols and drafting standards for electronic schematics. Ladder diagrams and logic hook-up drawings. CAD: Creating complex figures by drawing only a quarter of the final object and using the MIRROR command to fill in the remaining three quarters. Creating complex figures by using repetitive polar and rectangular array patterns. Theory: Laying out components for printed circuit board design. Choice of current carrying trace width. CAD: Using the INSERT command to create an schematic drawing from a library of standard active and passive electronic symbols (IEEE) and incorporating standard diagrammatic wiring rules and component labeling. Theory: Additional course material & course review CAD: Using the BLOCK command to create a collection of standard fluid power symbols using them to lay out a compressed air schematic drawing. Theory Test: Multiple choice & sketching Exercise #13 Pictorial Bar Chart (mechanical components) Prepared Notes #1 Exercise #18 - Interociter Exercise #16 - Tritium Infusion Plate Prepared Notes #2 Exercise #22 - Electronic Schematic Exercise #23 Compressed Air Drive System Theory Test = 20% (1.5 Hrs) 14 3D Basics CAD: Setting up and working in the 3D environment. Concept of viewports and workplanes. Use of the EXTRUDE and SUBTRACT commands. Spatial rotation of a body within a viewport. Shading a body. Adding a standard titleblock and printing. Exercise #30 - L-Block Exercise #31 - Base Bracket 15 Final CAD Test CAD Test: Drawing test incorporating all techniques discussed during course. Final CAD Test = 35% (2 Hrs) [NOTE: Course content including drawing assignments and/or tests may be added, changed or deleted because of extenuating circumstances.] SETAS: THIS COURSE ADHERES TO ALL COLLEGE POLICIES (See College Calendar) Page 7