Glass Instalation Guide PRIVA-LITE. Updated v
|
|
- Basil Anderson
- 5 years ago
- Views:
Transcription
1 PRIVA-LITE Glass Instalation Guide Updated v 5.0
2 PRIVA-LITE? T TABLE OF CONTENTS 1. Fixed frame application Butt joint application 9 3. Door application Bathroom application Floor and ceiling application 13 1
3 1. FIXED FRAME APPLICATION Never expose the PRIVA-LITE to temperatures over 60 C Hot spots such as light spot, cooking table top may by consequence never be close to PRIVA-LITE panels. For external applications, PRIVA-LITE has to be assembled in DGU or TGU with low e glazing. It has to be assembled with solar control glazing in sunny countries or on South & West façades. 1.1 Frame characteristics PRIVA-LITE can be fixed in PVC, aluminium or timber frames. If the framing or the trimming are conductive (aluminium, lacquered or stainless steel, ), it is then necessary to ground it either on the earth of the building or on the earth terminals of the power supply unit. Make sure that allframing segments are interconnected. If not each segment must be independently connected to earth. Holes of 10mm of diameter have to be drilled in the frame to allow the female connectors of the glass cables to pass. The rebate height has to be min 18mm for PRIVA-LITE single glazing and min 20mm for PRIVA-LITE assembled in double glazing. When PRIVA-LITE is assembled in double glazing then please make sure that the frames are correctly drained and ventilated. Since PRIVA-LITE may not undergo a pressure of more than 10N/cm? make sure that the frame will be at least 4mm wider than the PRIVA-LITE panel. 2
4 1. FIXED FRAME APPLICATION 1.2 U Profile GLASS CABLE Length 100cm Diameter 5,5 mm +/-0.3mm + Molex female connector (8mm dia) EVA MOLDING MULTISIL SILICONE NON ACTIVE AREA 9mm GLASS LC FILM Top position MULTISIL SILCIONE U PROFILE SETTING BLOCK 3
5 1. FIXED FRAME APPLICATION 1.2 U Profile U PROFILE BottomPosition GLASS LC FILM NON ACTIVE AREA9mm MULTISIL SILICONE EVA MOLDING SETTING BLOCKS GLASS CABLE Length 100cm Diameter 5,5 mm +/-0.3mm + Molex female connector (8mm dia) 4
6 1. FIXED FRAME APPLICATION 1.3 U Profile + cavity GLASS CABLE Length 100cm Diameter 5,5 mm +/-0.3mm + Molex female connector (8mm dia) EVA MOLDING MULTISIL SILICONE NON ACTIVE AREA 9mm GLASS LC FILM Top position MULTISIL SILCIONE SETTING BLOCK 5
7 1. FIXED FRAME APPLICATION 1.3 U Profile + cavity GLASS LC FILM Bottomposition MULTISIL SILICONE NON ACTIVE AREA 9mm EVA MOLDING SETTING BLOCK GLASS CABLE Length 100cm Diameter 5,5 mm +/-0.3mm + Molex female connector (8mm dia) 6
8 1. FIXED FRAME APPLICATION 1.4 Installation in 5 steps Step 1 : Before fixing the PRIVA-LITE in its frame, make sure that the frame is clean and that a grommet has been fixed on each holes to prevent the damaging of the extension cable. Since PRIVA-LITE may not undergo a pressure of more than 10N/cm? make sure that the frame will be at least 4mm wider than the PRIVA-LITE panel. Step 2 : Pass the extension cables while making sure that the male connector of the cable is on the panel side Use only the extension cables delivered by Glassolutions Saint-Gobain between the power supply unit and the PRIVA-LITE panels. Step 3 : Connect the male connector of the extension cable to the female connector of the PRIVA-LITE panel. Make sure that connector is fully pushed in to get a good electrical insulation. Extension cable with Molex male connector Glass cable with Molex female connector 7
9 1. FIXED FRAME APPLICATION 1.4 Installation in 5 steps Step 4 : Place the PRIVA-LITE panel in its frame and wedge it with setting blocks. Only hard wood setting blocks may be used. Make sure that the thickness of the setting blocks is minimum 8mm to avoid crushing the EVA moulding, the connector and the cable. Step 5 : Sealing of the frame. Only the Multisil silicone delivered by Glassolutions Saint-Gobain and products approved by Saint-Gobain may come in to contact with the edges of the glass. Preformed sealing joints can be used unless they remain only in contact with the surface of the PRIVA-LITE. Step 5 : Sealing of the frame. In case of DGU, the outside sealing can be done with silicone DC993 and DC3362. But at the inner side, PRIVA-LITE s side, only the Multisil silicone delivered by Glassolutions Saint-Gobain can be used. EXTERIOR ELECTRODE PRIVA -LITE INTERIOR 76 NON ACTIVE AREA EVA MOLDING 8
10 2. BUTT JOINT APPLICATION When PRIVA-LITE panels are used as a glass wall without any vertical profiles (butt jointed glasses) then only the Multisil silicone delivered by Glassolutions Saint-Gobain may be used for joints. Available colours: Translucent, black (RAL 9005), grey (RAL 7042), white and brown (RAL 8019). Prior to silicone application, preferably place masking tape on both sides to obtain a neat joint, especially when edge is sandblasted. Remove masking tape before full reticulation of the silicone. To achieve a smooth butt joint finish, only use soapy water spray (neutral washing up liquid + water). Only products approved by Saint-Gobain may come in to contact with the edge of the glass. No other product such as glue, adhesive, sealant, gasket, plastic strip primer and finisher liquid can be used in contact with the edge. A min of 4mm separation between the panels is recommended. In case of bow, place bow in same direction for side by side panel and use 2 wooden blocks with a screw to middle height of the glass to move closer together the adjacent panels. 9
11 3. DOOR APPLICATION Never expose the PRIVA-LITE to temperatures over 60 C Hot spots such as light spot, cooking table top may by consequence never be close to PRIVA-LITE panels. For external applications, PRIVA-LITE has to be assembled in DGU or TGU with low e glazing. It has to be assembled with solar control glazing in sunny countries or on South & West façades. 3.1 Swinging and pivoting door For door application, PRIVA-LITE panel is either fixed in a frame or in top and bottom profiles (swinging door). Frameless PRIVA-LITE doors are impossible. In both cases, extension cables delivered by Glassolutions Saint-Gobain will have to pass through a lead cover such as Assa Abloy EA280 or EA281 Door handle and lock have to be fixed on the frame. Rectangular notch for the handle and the lock can be cut in the glass (and LC film) on demand and under specific conditions. If the lock has to work as a switch (PRIVA-LITE switched OFF when the door is locked), then the use a specific relays, such as the RSB relay from Schneider, is recommended. Electrical diagram is available on demand. For toilet door, we recommend to use our High Privacy PRIVA-LITE version (higher hiding power). Since PRIVA-LITE panel could slightly bend, we recommend to frame twin doors. Door handle and lock have to be fixed on the frame. Rectangular notch for the handle and the lock can be cut in the glass (and LC film) on demand and under specific conditions. If the lock has to work as a switch (PRIVA-LITE switched OFF when the door is locked), then the use a specific relays, such as the RSB relay from Schneider, is recommended. Electrical diagram is available on demand. For toilet door, we recommend to use our High Privacy PRIVA-LITE version (higher hiding power). Since PRIVA-LITE panel could slightly bend, we recommend to frame twin doors. 10
12 3. DOOR APPLICATION Never expose the PRIVA-LITE to temperatures over 60 C Hot spots such as light spot, cooking table top may by consequence never be close to PRIVA-LITE panels. For external applications, PRIVA-LITE has to be assembled in DGU or TGU with low e glazing. It has to be assembled with solar control glazing in sunny countries or on South & West façades. 3.2 Sliding door When PRIVA-LITE is used as a sliding door it has to be framed on 4 sides. Door handle and lock have to be fixed on the frame. Rectangular notch for the handle and the lock can be cut in the glass (and LC film) on demand and under specific conditions For sliding door application, a specific extension cable is needed. Please contact Glassolutions Saint-Gobain for more information. Extension cables delivered by Glassolutions Saint-Gobain will have to pass through an Energy chain system. For correct installation, follow Igus E-ChainSystem - Installation Guide.. 11
13 4. BATHROOM APPLICATION Always refer to CEI and most of all to National Electric Code Zone 0 (shower tray) : no PRIVA-LITE. Zone 1 (<120cm from water source) : only embedded DGU PRIVA-LITE IPX7 (PRIVA-LITE on the opposite side of bathroom). Zone 2 (>120cm from water source) : single glazing PRIVA-LITE IPX7 possible only if it s fixed in a frame perfectly sealed In case of bath, single glazing PRIVA-LITE IPX7 is possible only if it is fixed aside and above the bath tub in a frame perfectly sealed. A continuous cable has to be used between the panel and the power supply unit fixed out of the zones 0, 1 and 2. 12
14 5. FLOOR AND CEILING APPLICATION As PRIVA-LITE may not undergo pressure higher than 10N/cm? it has by consequence to be fixed as a second skin of a LITE-FLOOR panels. See drawing hereunder. See national regulation to define the thickness of the LITE-FLOOR panel Support structure will be visible through these transparent areas SGG LITE FLOOR PRIVA LITE Support structure Support structurehas to be min = to 1,5 the thickness of the SGG LITE FLOOR or PRIVA -LITE Never expose the PRIVA-LITE to temperatures over 60 C Hot spots such as light spot, cooking table top may by consequence never be close to PRIVA-LITE panels. For external applications, the SGG LITE-FLOOR has to be laminated with a solar control glazing as external glass and the area between the SGG LITE-FLOOR and PRIVA-LITE has to be correctly ventilated to avoid any overheating of the PRIVA-LITE 13
15 This document contains all essential instructions for the electrical installation of PRIVA-LITE panels on the power supply unit PVL XL. All documents previously published by Glassolutions are replaced by the present document. Glassolutions has taken every reasonable measure to ensure that the information contained in the present leaflet was exact at the time of its publication. However, Glassolutions keeps the right to modify or add any information without previous notice 14
Installation Instructions
Installation Instructions Alcove Enclosure Before Installation please check that your shower enclosure system is undamaged Please read these instructions carefully March 2015 TOOLS REQUIRED Electric or
More informationEB/MM Upd.2_ CLIP-IN DOOR FOR SHOWERS FT
EB/MM Upd.2_20.06.16 CLIP-IN DOOR FOR SHOWERS FT 8570216 1 1 6 Working in partnership with Saint-Gobain Glassolutions, Adler SAS has developed Clip-In Door, a hinge that can be used to create glass doors
More informationIMPORTANT INSTALLATION GUIDE VALENCIA SQUARE CORNER SHOWER READ ALL INSTRUCTIONS CAREFULLY BEFORE STARTING THE
INSTALLATION GUIDE VALENCIA SQUARE CORNER SHOWER NOTE: Acrylic wall, tray and tapware not included. Supplied handles may differ from image. SEALANT REQUIRED TO COMPLETE THIS INSTALLATION: (Not supplied)
More informationALLORA SWING PANEL INSTALLATION INSTRUCTIONS
ALLORA SWING PANEL INSTALLATION INSTRUCTIONS Before Installation Please check that your Allora Swing Panel is undamaged SEQUENCE OF INSTALLATION These instructions are also available from the Athena website:
More informationDeauville Installation Guide
vjul16 (for 17 or 24 mm Surface Wall Profiles) DO NOT ASSEMBLE WITHOUT FULLY READING THESE INSTRUCTIONS Page 2 Thank you for purchasing this Deauville shower enclosure. Please study these instructions
More informationENARC CONSULTANTS. M. G. ROAD, THRISSUR - 1 Ph. : &
ENARC CONSULTANTS M. G. ROAD, THRISSUR - 1 Ph. : 2441901 & 2441905 SCHEDULE FOR INTERIOR FURNISHING WORK FOR RASMECC BRANCH (FIRST FLOOR) SBI, CONSTRUCTION OF BUILDING AT THRISSUR - 1 Fully Glazed Partitions
More informationDeauville Installation Guide
vjul16 (for Recessed Wall Profiles) DO NOT ASSEMBLE WITHOUT FULLY READING THESE INSTRUCTIONS Page 2 Thank you for purchasing this Deauville shower enclosure. Please study these instructions carefully before
More informationIMPORTANT INSTALLATION GUIDE VALENCIA ANGLE CORNER SHOWER READ ALL INSTRUCTIONS CAREFULLY BEFORE STARTING THE INSTALLATION
INSTALLATION GUIDE VALENCIA ANGLE CORNER SHOWER SEALANT REQUIRED TO COMPLETE THIS INSTALLATION: (Supplied) Sika Sikasil NG (Arctic White) To seal the WHITE shower door and returns to the shower tray. Usage:
More informationB A T H R O O M G L A S S
mistley B A T H R O O M G L A S S vaug16 Page 2 Thank you for purchasing this Trinity shower screen. Please study these instructions carefully before assembly and installation and check all supplied parts
More informationUNIT No FRAMELESS PIVOT SHOWER DOOR
INSTALLATION INSTRUCTIONS UNIT No. 3600 FRAMELESS PIVOT SHOWER DOOR NEED INSTALLATION HELP? Call 1-800-45-BASCO (452-2726) Monday - Friday 8:00 A.M. - 4:30 P.M. Eastern Time QCI0020 Rev. 3 Page 1 of 8
More informationInstallation Instructions
Installation Instructions Angle orner & Round Enclosures efore Installation please check that your shower enclosure system is undamaged Please read these instructions carefully Oct 2015 TOOLS REQUIRE Electric
More informationHardware Fitting Accessories Door Seals
Areas of application Protection against cold, draught and vermin Reduces light leakage, sound insulation Smoke control, fire resistance Reduces the energy consumption of air conditioning systems (see following
More informationAllora ALCOVE ENCLOSURE INSTALLATION BEFORE INSTALLATION CHECK THAT YOUR ALLORA SHOWER ENCLOSURE SYSTEM IS UNDAMAGED
Allora ALCOVE ENCLOSURE INSTALLATION BEFORE INSTALLATION CHECK THAT YOUR ALLORA SHOWER ENCLOSURE SYSTEM IS UNDAMAGED ALCOVE SHOWER Your shower can be installed to open Left hand or Right hand by rotating
More informationPage 1 of Ch 6. A Lecture note on Building Technology By Kishor Thapa
CHAPTER-6 Doors and windows 6.1 Doors: frames, shutters and their fixing details The function of a door is to give access to building and to different parts of the building and to deny the access whenever
More informationUpdates Interior compensation of varying infill thicknesses. THERM + V curtain walls
Aluminium curtain wall from 10 to 24 can be compensated T12 = Depths from 25 Cover profile /15 013003 6 m Cover profile /12 013004 6 m Structural profile / V 113005 6 m Pressure profile 47 118005 6 m 011070.LI
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS BUILDERS CHOICE FRAMED Shower Height Swing Door Model: L533 Rev. 09.03.13 MAINTENANCE: Two primary materials are used to manufacture your new Aquatic enclosure; tempered glass
More informationCardo DOOR & RETURN SHOWER ENCLOSURE INSTALLATION PLEASE READ THESE INSTRUCTIONS CAREFULLY.
Cardo DOOR & RETURN SHOWER ENCLOSURE INSTALLATION PLEASE READ THESE INSTRUCTIONS CAREFULLY. IT IS RECOMMENDED TO USE A TRAINED SHOWER INSTALLER FOR THIS SHOWER TO OBTAIN THE BEST INSTALLATION. D Square
More informationVALENCIA RONDO DOOR WITH RETURN
VALENCIA RONDO DOOR WITH RETURN INSTALLATION GUIDE SEALANT REQUIRED TO COMPLETE THIS INSTALLATION: ( not supplied) Sika Silaflex NG To seal the WHITE shower door and returns to the shower tray. Usage:
More informationPortofino Installation Guide
vjul16 (for 17 or 24 mm Surface Wall Profiles) DO NOT ASSEMBLE WITHOUT FULLY READING THESE INSTRUCTIONS Page 2 Thank you for purchasing this Portofino shower enclosure. Please study these instructions
More informationPortofino Case2 Installation Guide
Portofino Case2 Installation Guide vjun16 (for 17 or 24 mm Surface Wall Profile) DO NOT ASSEMBLE WITHOUT FULLY READING THESE INSTRUCTIONS Page 2 Thank you for purchasing this Portofino Case 2 shower enclosure.
More informationASS 70 FD folding/sliding door installation guide
ASS 70 FD folding/sliding door installation guide 2 Preparation IMPORTANT These doors should be fitted by competent and trained installers. Please read these instructions thoroughly before beginning the
More informationSLIDING MECHANISM TROLLEY CATCH TROLLEY ASSEMBLY FLOOR GUIDE
Set A Set B PFD30 Fire Door Kit FITTING INSTRUCTIONS For use with 44mm thick doors only For Single and Double doors IF INSTALLING A TOUCH LATCH, PLEASE READ THE CORRESPONDING FITTING INSTRUCTIONS FIRST
More informationArchitect: Daluz/González Architekten Photo: Peter Baracchi CP 155 SLIDING DOOR INSTALLATION GUIDE. Edition 15/21
Architect: Daluz/González Architekten Photo: Peter Baracchi CP 155 SLIDING DOOR INSTALLATION GUIDE Edition 15/21 INDEX 1. IMPORTANT INFORMATION... 4 1.1. Lift & slide door overview... 5 1.2. Details...
More informationAn adjacent sauna must be well insulated and located to leave a gap of at least 10 cm (4 ) for air to circulate between the sauna and the steam room.
Please read through these instructions carefully before starting assembly or installation work. There must be no form of heating in the steam room, apart from the steam itself. The ambient temperature
More informationIF INSTALLING ANY OF THE PORTMAN SELF CLOSING SYSTEMS, PLEASE READ THE CORRESPONDING FITTING INSTRUCTIONS SUPPLIED WITH THE CLOSING SYSTEM FIRST
Set A Set B PFD60 Fire Door Kit FITTING INSTRUCTIONS IF INSTALLING ANY OF THE PORTMAN SELF CLOSING SYSTEMS, PLEASE READ THE CORRESPONDING FITTING INSTRUCTIONS SUPPLIED WITH THE CLOSING SYSTEM FIRST SUGGESTED
More informationSLIDING MECHANISM TROLLEY CATCH TROLLEY ASSEMBLY FLOOR GUIDE
Set A Set B PFD30 SG Fire Door Kit FITTING INSTRUCTIONS For use with 44mm thick doors only For Single and Double doors SUGGESTED TOOLS DRILL G-CLAMP TAPE MEASURE (Image for reference only) HACKSAW POCKET
More informationAcid etched float glass
Description Acid etched float glass Golden Faith acid etched glass-non finger print has a uniformly smooth, silky surface, which is translucent and matte in appearance. It transmits levels of diffused
More informationIn-line Patio Fabrication & Installation
In-line Patio Fabrication & Installation Instructions 2 Pane Patio p2 Cutting and Preparation p2 Welding and Cleaning p2 Assembly p2 Fabrication Instructions for 3/4 Pane Lock Style p3 Installation (removable
More informationInstallation - Sub Cills
Installation - Sub Cills Fitting of Subcill Drainage paths through the sub-cill can be seen on the illustration alongside so care must be taken to ensure they are not obstructed and that screw fixings
More informationINOVO 2-LITE SLIDING PATIO DOOR
INOVO 2-LITE SLIDING PATIO DOOR ASSEMBLY AND INSTALLATION INSTRUCTIONS IMPORTANT: READ THE INSTRUCTIONS AND FAMILIARIZE YOURSELF WITH THE DOOR PARTS AND PIECES BEFORE BEGINNING ASSEMBLY AND INSTALLATION.
More information340 & 350 SERIES BATH ENCLOSURES
INSTALLATION INSTRUCTIONS 340 & 350 SERIES BATH ENCLOSURES 800-643-1514 www.alumaxbath.com Copyright Alumax Bath Enclosures 2010. All rights reserved. LIMITED WARRANTY AND REMEDY ALUMAX BATH ENCLOSURES
More information340 & 350 SERIES DELUXE FRAMELESS BYPASS
BATH ENCLOSURES An Alcoa Company Tel: 800-643-1514 Fax: 870-234-3181 www.alumaxbath.com INSTALLATION INSTRUCTIONS 340 & 350 SERIES DELUXE FRAMELESS BYPASS BATH ENCLOSURES Copyright Alumax Bath Enclosures
More informationSide Light Frame Pack Assembly Instructions
Please read this complete set of assembly instructions before starting the installation and only when you understand the construction method start to follow the step by step guide. IDENTIFY THE PACK CONTENTS
More informationINSTALLATION MANUAL 32273/1205 C C-403 GB - F - D - NL - ES - I - S - SLO
INSTALLATION MANUAL 32273/1205 C-402 - C-403 GB - F - D - NL - ES - I - S - SLO 1A 1B ENGLISH GENERAL INFORMATION The Cassette toilet is available in 2 types: C-402 Cassette toilet with built-in water
More informationINSTALLATION INSTRUCTIONS DANUBE ACRYLIC NEO ANGLE
INSTALLATION INSTRUCTIONS DANUBE ACRYLIC NEO ANGLE March 2013 DOOR 2 Page 1 of 5 INSTALLATION INSTRUCTIONS NEO ANGLE 6MM FRAMELESS AND 4MM FRAMED SHOWER DOOR DANUBE, DELTA, SIGNATURE, OCEANIA, CASCADE
More informationFIG. #1 - ASD-90 & USD-90 Shower Door Assembly
Installation Instructions for the Accent/Euro Collection FIG. #1 - ASD-90 & USD-90 Shower Door Assembly #1021 #1021 1 23 25 2 #1020 6 5 12 #1020 9 24 9 8 Hinge Assembly 2109, 2201, 2212, 2213, 2220 7 Please
More informationCINTRALUX ALU BARREL VAULT EP 10/10
CINTRALUX ALU BARREL VAULT EP 10/10 Installation instructions EN 14963 Artn 43984 E_MH_Cintralux EP 10/10 mm AG.PLASTICS QUALITY 1 Installation instructions Cintralux aluminium barrel vault: Cintralux
More information1/4 FRAMELESS SLIDING DOOR FOR TUB OR SHOWER 4400A-4500A
1/4 FRAMELESS SLIDING DOOR FOR TUB OR SHOWER 4400A-4500A F AB GLASS AND MIRROR www.fabglassandmirror.com Call: +1 888-474-2221 Fax: (614)-334-4919 Office Timing: 8:30-18:00 EST info@fabglassandmirror.com
More informationSide Light Frame Pack Assembly Instructions
Side Light Frame Pack Assembly Instructions Please read this complete set of assembly instructions before starting the installation and only when you understand the construction method start to follow
More informationMethod of Build 1. General
Method of Build 1 General GLAZED ELEVATIONS Viso Double Glazed in glazed form differs from many other systems as the vertical joints can have Viso dry joints or the unique HIDDEN mullion post between glazed
More informationPlatinum Swing Panel Installation Instructions
Platinum Swing Panel Installation Instructions The Standard Platinum Swing Panel is designed to fit baths with a perimeter lip no taller than 20mm. If installing onto baths without a perimeter lip an optional
More informationASS 70 FD folding / sliding door. Installation Guide
ASS 70 FD folding / sliding door Installation Guide IMPORTANT! These doors should be fitted by competent and trained installers. Please read these instructions thoroughly before beginning the installation.
More informationIMPORTANT!!! ASSEMBLY ASSEMBLY INSTRUCTIONS. (Internal Dimensions)
ASSEMBLY ASSEMBLY INSTRUCTIONS (Internal Dimensions) Ent Spec Edition Ltr v-0- Overall dimensions including base: 7. L x 9 W x 0 H cms 97.5" L x 7" W x 8.7" H IMPORTANT!!! Please read these instructions
More informationSHOWERLUX HELPLINE: TEL: SHOWERLUX (UK) Ltd.
SHOWERLUX HELLIE: TEL: 02476 882518 Fax: 02476 882539 Email: technical@showerlux.co.uk Email: spares@showerlux.co.uk SHOWERLUX (UK) Ltd. Sibree Road, Coventry, West Midlands CV3 4FD Tel: 02476 639400 Fax:
More information40mm Thermoclick. Type II Class 1 Clear Satin Anodize - 201R1 (Mid Grade Commercial)
http://www.sundancesupply.com 40mm Thermoclick Type II Class 1 Clear Satin Anodize - 201R1 (Mid Grade Commercial) U-Profile 12' Lengths $39 Out System offers a complete set of extrusions and accessories
More informationInstructions for Installation on a Pitched Roof LIGHTWAY optical tube LW 260, LW 320, LW 520, LW 760
Lightway, s.r.o. Registered office: Ledvinova 1714, 149 00 Praha 4 Offices: Za Humny 1054/4a, 161 00 Praha 6 tel.: 235 300 694, fax: 235 300 218 Company ID No.: 63669366, Tax ID No.: CZ63669366 Bank: KB
More informationPrel-Lam LC-LTI Liquid Crystal Laminated Glass
Prel-Lam LC-LTI Liquid Crystal Laminated Glass 1. FEATURES Liquid crystal glass is laminated glass that is connected to a switch-operated electric circuit. The appearance of this glass changes depending
More informationSUPREME WALL GARDEN ASSEMBLY INSTRUCTIONS 24/08/16 www.hallsgreenhouses.com Please refer to website for the most up to date instructions. SAFETY WARNING 1. Always wear protective glasses, shoes, gloves
More informationStandard program overview Steel smoke-proof doors
Smoke-proof doors Standard program overview Steel smoke-proof doors Pos. Product 1 RS-1 Steel door (thin rebated) Smoke-proof door in accordance EN 1634-3 / DIN 18095 Dimensions W 625-1350 H 1750-2500
More information1/4 FRAMELESS SLIDING DOOR FOR TUB OR SHOWER
1/4 FRAMELESS SLIDING DOOR FOR OR SHOWER INSTALLATION INSTRUCTIONS NEED INSTALLATION HELP? Call 1-800-45-BASCO (452-2726) M onda y - Friday 8 :00 A.M. - 4:30 P.M. Eastern Time MAINTENANCE: Two primary
More informationFACTS ABOUT TP LITE FRAMELESS P
FRMELESS PRTITION FCTS OUT TP LITE TP Lite is a frameless fully glazed partition system with a single glass layer TP Lite with door frames ensures sound reduction that meets normal sound demands for meeting
More informationmistley PELE Installation Guide vapr16 Mistley Bathroom Glass Limited No 4 One Mistley Quayside, High Street, Mistley, Essex CO11 1AL England
mistley BAT HRO O M G LASS vapr16 Page 2 Thank you for purchasing this Pele shower screen. Please study these instructions carefully before assembly and installation and check all supplied parts immediately
More informationFIG. #1 - ASD & USD 180/280 Shower Door Assembly
FIG. #1 - ASD & USD 180/280 Shower Door Assembly USD180 / 280 Euro Stall Header #1020 16 16 1 16 4 ASD180 / 280 Accent Stall Header #1021 5 3 8 6 7 8 Hinge Assembly: 2220, 2201, 2185, 2271, 2213 18 22
More informationVALENCIA CORNER DOOR WITH RETURN
VALENCIA CORNER DOOR WITH RETURN INSTALLATION GUIDE SEALANT REQUIRED TO COMPLETE THIS INSTALLATION: ( not supplied) Sika Silaflex NG To seal the WHITE shower door and returns to the shower tray. Usage:
More informationINSTALLATION GUIDE SLIMLINE ROOF LANTERN 4 PANE CONFIGURATION
INSTALLATION GUIDE SLIMLINE ROOF LANTERN 4 PANE CONFIGURATION SLIMLINE STEP-BY-STEP INSTALLATION GUIDE Thank you for choosing Roof Maker, we hope you are delighted with your new rooflight. Our roof lanterns
More informationExploded View PAGE 2 OF 9
Argon 02 Exploded View PAGE 2 OF 9 Supplied Parts Underframe Underframe Insert Wall to Glass Hinge Door Handle Door Bottom Seal Hinge Seal Bubble Seal PAGE 3 OF 9 Important Information This shower screen/enclosure
More informationSLIDING DOOR for CORNER installation ONLY - this door closes to side panel -
by KUDOS INSTALLATION INSTRUCTIONS SLIDING DOOR for CORNER installation ONLY - this door closes to side panel - Please read these instructions throughout before installing as incorrect fitting will invalidate
More informationMonaco Installation Guide - Surface Profiles
v1 Page 1 Thank you for purchasing this Monaco shower screen. Please study these instructions carefully before assembly and installation and check all supplied parts immediately upon receipt. These instructions
More informationINSTALLATION INSTRUCTIONS
EDGE PIVOT DOOR EPDSC0760 EPDSC0800 EPDSC0900 EPDSC1000 ESPSC0760 ESPSC0800 ESPSC0900 ESPSC1000 PIVOT DOOR IN ALCOVE PIVOT DOOR & SIDE PANEL INSTALLATION INSTRUCTIONS IMPORTANT - Please read before installation
More informationSMART SYSTEMS VISOGLIDE+ INSTALLTION GUIDE
SMART SYSTEMS VISOGLIDE+ INSTALLTION GUIDE Please read guide before beginning any installation. Instructions/Guides Keys & Handle Screw Covers Interlock Covers Anti-Lift & Rubber Stops Anti-Lift for Slim
More informationHow To Install Windows: Nail-Fin Application
How To Install Windows: Nail-Fin Application Required Tools & Materials: Materials: 1 3/4" galvanized roofing nails. Nails must penetrate at least 1" into framing For mulled and/or DP50 or above units:
More informationINFINITE RANGE - CENTRE FOLDING DOOR
INFINITE RANGE - CENTRE FOLDING DOOR CENTRE FOLDING DOOR ONLY ( RECESS) Please read these instructions before installing, as incorrect fitting will invalidate the guarantee-carry out each stage before
More informationFor Installer. Duration Windows. Assembly Guide Durafold 1000
For Installer Assembly Guide Durafold 1000 Contents Title Page Number Handling Manual Blinds 4 Handling Electronic Blinds 5 Drainage 63 Outer Frame Assembly (Kit Form Door Only) 7 15mm Low Threshold Assembly
More informationGluing windows with SABA Glasstack 760
Info sheet 208 Gluing windows with SABA Glasstack 760 Version 2008-05-08 EN, replaces all prior versions Page 2 of 9 Info sheet 208 Gluing windows with SABA Glasstack 760, version 2008-05-08 EN 1. Introduction
More informationInstallation Guidelines For Quaker Window Products Aluminum flange fin sub sill & receptor system using a T mulled twin window unit.
Installation Guidelines For Quaker Window Products Aluminum flange fin sub sill & receptor system using a T mulled twin window unit. Installer: Read these instructions completely before starting any installation.
More informationPREMIUM GLASS BATH SCREEN
PREMIUM GLASS BATH SCREEN INSTALLATION GUIDE Bath screens must be installed in situations where the floor of the bathroom has a waterproof membrane installed. For New Zealand, the bath screen must be installed
More informationSEMI-FRAMELESS DOOR WITH GLASS PANEL & BENCH GLASS
INSTALLATION INSTRUCTIONS 1-800-669-9867 800-643-1514 www.alumaxshowerdoor.com SEMI-FRAMELESS DOOR WITH GLASS PANEL & BENCH GLASS 395CV-1217 Yes! Guaranteed Forever! Proudly Made in Kansas, USA 202 Anderson
More information1/4 FRAMELESS DOOR WITH INLINE PANEL 1413A-1713A-1813A
1/4 FRAMELESS DOOR WITH INLINE PANEL 1413A-1713A-1813A F AB GLASS AND MIRROR www.fabglassandmirror.com Call: +1 888-474-2221 Fax: (614)-334-4919 Office Timing: 8:30-18:00 EST info@fabglassandmirror.com
More informationEXPOSED FASTENING SYSTEM WITH SCREWS OR RIVETS
External EXPOSED FASTENING SYSTEM WITH SCREWS OR RIVETS Parklex Facade may be installed using mechanical fasteners, such as screws or rivets. The panels are attached to vertical battens. In the event that
More informationSimplex Baseboard System Baseboard System
Simplex Baseboard System Baseboard System I Complete installation programme I Trouble-free and time-saving installation I Various connection kits for all types of pipe Our service to you I Simplex Products
More informationSemi-Frameless Hinged Door With Panel And Return
202 Anderson Ave., Belvue, KS 66407 Phone: 800-669-9867 Fax: 800-393-6699 www.onyxcollection.com 800-643-1514 www.alumaxbath.com Semi-Frameless Hinged Door With Panel And Return Full Showers with Return
More informationINOVO 4-LITE SLIDING PATIO DOOR ASSEMBLY AND INSTALLATION INSTRUCTIONS
INOVO 4-LITE SLIDING PATIO DOOR ASSEMBLY AND INSTALLATION INSTRUCTIONS IMPORTANT: READ THE INSTRUCTIONS AND FAMILIARIZE YOURSELF WITH THE DOOR PARTS AND PIECES BEFORE BEGINNING ASSEMBLY AND INSTALLATION.
More informationDura-Lock Roof System
DLR-14 Dura-Lock Roof System Assembly and Installation Instructions Read the instructions before starting the job. They explain the steps required to produce a finished product that will meet factory specifications.
More informationHow to Build Your Custom Teardrop Camper. 5 x 10 Trailer. 5 Tall Cabin
How to Build Your Custom Teardrop Camper 5 x 10 Trailer 5 Tall Cabin Contact: hennesseystealth@bigteardrop.com http://www.bigteardrop.com ebay Seller ID: hennesseystealth1957 United States Copyright TXu
More informationINSTALLATION MANUAL FORTRESS SERIES
Guardian Security Structures TEL 1-406-212-2334 EMAIL rg@gssdoors.com WEB www.gssdoors.com FORTRESS SERIES GENERAL INSTALLATION GUIDELINES 1. The door frame is installed using 16 bolt screws 7,5 mm in
More information1/4 FRAMELESS SLIDING DOOR FOR TUB OR SHOWER
1/4 FRAMELESS SLIDING DOOR FOR OR SHOWER INSTALLATION INSTRUCTIONS NEED INSTALLATION HELP? Call 1-800-45-BASCO (452-2726) M onda y - Friday 8 :00 A.M. - 4:30 P.M. Eastern Time MAINTENANCE: Two primary
More informationGlues and mastics. SILICONE ADHESIVE SEALANT 42 Marine silicone SOROMAP...42 Silicone colour RAL...42 Glue mastic MS1000 TECHNIFIX...
Glues and mastics In this chapter, we present all the products that you need to make sticking, seals, insulation and teak deck. SILICONE ADHESIVE SEALANT 42 Marine silicone SOROMAP......................................42
More informationDubnium 11 Installation Instructions & Parts List
Dubnium 11 Installation Instructions & Parts List Illustration Dubnium, H1 Handle Right Hand: Open Out Page 1 of 25 IMPORTANT This shower screen / enclosure must be installed by suitably qualified individuals.
More informationShowerlux roduct made by The Duscholux Group Showerlux Spares Shop www.showersealspares.co.uk Due to a policy of continuous improvement and product development, Duscholux reserves the right to amend specification
More informationUnit No. 4400, 4500 Classic Frameless Sliding Tub/Shower Enclosure INSTALLATION INSTRUCTIONS
Unit No. 4400, 4500 Classic Frameless Sliding Tub/Shower Enclosure INSTALLATION INSTRUCTIONS MAINTENANCE: Two primary materials are used to manufacture your new Basco enclosure: tempered glass and anodized
More informationTable and Furniture Base Fittings Plinth Adjusting Fittings
Adjusting screw with M8 or M thread Rigid, for glide inserts, steel thread Finish/Colour: Black, thread galvanized Version: With acceptance Ø30 mm Thread M8 650.22.381 M 650.22.382 Packing: 1 or 0 pcs.
More informationCORNER ENTRY ENCLOSURE
CORNER ENTRY ENCLOSURE SUPREME INSTALLATION INSTRUCTIONS IMPORTANT - Please read before installation Please read these instructions carefully before starting installation and keep in a safe place for future
More informationGallium 03 Installation Instructions & Parts List
Gallium 03 Installation Instructions & Parts List Illustration Gallium 03, H1 Handle Left Hand: Open Out 04/05/2016 Revision 1.1 Page 1 of 19 IMPORTANT This shower screen / enclosure must be installed
More informationLiniar Window. installation guide
Liniar Window installation guide This installation guide is designed to show you the best way to fit Liniar windows, and covers all styles of window made from Liniar s lead-free 70mm PVCu profile. Not
More informationPATIO INSTALLATION MANUAL
PATIO INSTALLATION MANUAL A few minutes spent reviewing the following instructions will help insure quick and proper assembly. The Patio Sauna Kit will arrive on a stretchwrapped pallet including pre-built
More informationSLIDING TUB / SHOWER ENCLOSURE WITH STATIONARY 90º PANEL
SLIDING TUB / SHOWER ENCLOSURE WITH STATIONARY 0º PANEL This instruction sheet applies to the following units. C, C7, C7, C77, C, C7 This instruction sheet also applies to the following units. VTE / VSE
More information28.00 Rmt sqm sqm
SEALED BID FORMAT FOR THE INTERIOR FURNISHING WORKS AT SBI CHALAKUDY BRANCH. Sl No. Description of item Quantity Unit Rate Amount 1 Counter Table :- The width and height of the table is 100cm and 75cm
More informationINFINITE RANGE - HINGE DOOR
INFINITE RANGE - HINGE DOOR HINGE DOOR + 1 SIDE RETURN PANEL (CORNER) Please read these instructions before installing, as incorrect fitting will invalidate the guarantee-carry out each stage before moving
More informationSERIES 3070-T MULTI-SLIDE ASSEMBLY & INSTALLATION INSTRUCTIONS
Table of Contents I. Care and Maintenance...2 II. Tools / Material & Sealant Requirements...2 III. Assembly and Installation...2 IV. Glazing Assembly...3 V. Panel Assembly...3 1. X Panel...3 2. O Panel...4
More informationInstallation Guide. Evolve bi-fold. 8. Door restrictor- optional p9. 1. Before you start p2. 9. Adjustment. 2. Measuring and surveying p2
Evolve bi-fold Installation Guide 1. Before you start p2 8. Door restrictor- optional p9 2. Measuring and surveying p2 3. Configuration details p4 4. Installation p5 5. Glazing p5 6. Glazing packer details
More informationargenta opening doors
invisidoor Invisible aluminium frame for interior doors Content invisidoor... 4 invisidoor AX / AX PRO... 10 invisidoor SD / SDX... 16 invisiplint... 22 general information... 27 THE INVISIDOOR CONCEPT
More information3/16 OR 1/4 FRAMELESS SWING DOOR WITH SINGLE INLINE PANEL OR TWO INLINE PANELS
/ OR / FRAMELESS SWING DOOR WITH SINGLE INLINE OR TWO INLINE S This instruction sheet applies to the following units with a magnetic handle. C7, C7, C79 This instruction sheet also applies to the following
More informationInstallation Instructions Student 101 Fume Cupboard
Installation Instructions Student 101 Fume Cupboard Refer drawing on next page 0. If your fume cupboard is supplied with a flatpack bench frame, see step1. If your fume cupboard will be mounted on an existing
More informationSide and rear window, assembly overview
64-7 Side and rear window, assembly overview 1 - Side/rear window Removing Unbroken Page 64-9 Broken Page 64-11 Installing Page 64-13 Curing time Page 64-21 Re-sealing Page 64-25 2 - PUR adhesive sealant
More informationTOYOTA MOTOR EUROPE CA Products Division Tel : Fax :
TOYOTA MOTOR EUROPE CA Products Division Tel : + 32 2 745 26 77 Fax : + 33 2 745 26 99 Ordering part numbers Comments Part Numbers Wooden floor one hatch PZ449-D3C42-11 one hatch with carpet PZ449-D3C42-01
More informationmethod of build Komfire-75 partitioning system 75mm Steel Stud & Plasterboard Partitioning System with Square Aluminium Cover Trims KOMFORT
821 811 342 821 835 853 863 840 12.5mm Plasterboard 837 75mm Steel Stud & Plasterboard Partitioning System with Square Aluminium Cover Trims Note: For clarity the cavity infill has not been shown 854 342
More informationMethod of Build 1. Fire. Sound
Method of Build 1 General Viso Fire & Acoustic in the solid form differs from most other systems as it can be erected using 12.5mm & 15.0mm boards within the same Aluminium framework. Also hidden fix board
More informationPanel Installation Instructions
EXTREMELY IMPORTANT INFORMATION PLEASE READ ENTIRE PACKET! Warranty Is Void If Panels Not Installed According to Instructions 1. WARNINGS & SPECIAL NOTES 1.1 Keep panels 24 from Heaters and shield Radiant
More informationMETL-VISION WINDOW SYSTEM FOR HORIZONTAL WALL PIONEERING INSULATED METAL PANEL TECHNOLOGY
METL-VISION WINDOW SYSTEM FOR HORIZONTAL WALL Window assembly GUIDE PIONEERING INSULATED METAL PANEL TECHNOLOGY PIONEERING INSULATED METAL PANEL TECHNOLOGY CONTENTS DETAIL TITLE FILE NO. PAGE NO. INTRODUCTION..................................................................
More informationINSTALLATION INSTRUCTIONS. Thermal Entrances AA 250/AA 425 THERMAL DOOR WITH TRIFAB 601/601T FRAMING
JANUARY, 2014 1 INSTALLATION Thermal Entrances AA 250/AA 425 THERMAL DOOR WITH TRIFAB 601/601T FRAMING INSTRUCTIONS 2 FRAME ASSEMBLY JANUARY, 2014 601442 SHEAR BLOCK BALL BEARING NRP BUTT (FACTORY APPLIED
More information