Dubnium 11 Installation Instructions & Parts List

Size: px
Start display at page:

Download "Dubnium 11 Installation Instructions & Parts List"

Transcription

1 Dubnium 11 Installation Instructions & Parts List Illustration Dubnium, H1 Handle Right Hand: Open Out Page 1 of 25

2 IMPORTANT This shower screen / enclosure must be installed by suitably qualified individuals. We recommend a minimum of two people for safe assembly of certain sections of this screen. Ensure all appropriate safety equipment, especially protective footwear, safety glasses and gloves are used. When drilling holes in ceramic tiles, use masking tape to prevent the drill from slipping: DO NOT use hammer action as this will crack the tiles. Use a high quality drill bit to ensure a clean, precise hole. Please leave these instructions with the customer following installation. PRIOR TO INSTALLATION Before disposing of the packaging and prior to commencing assembly, please check all the components to ensure that they have been supplied correctly and are undamaged. Subsequent claims for missing or damaged pieces will not be accepted once the packaging has been disposed of and installation commenced. In the event of any queries please contact your supplier quoting the relevant model information. The Tray / Tiled floor on which this screen is to be installed must be level on all sides. It may be necessary to use alternate fixings to those supplied, depending on the properties of the walls to be fixed to. Use the protective corners supplied at all times until the glass is moved to its final position. Ensure that the glass is installed correctly, taking care to avoid installing the glass upside down. On certain panels an easy clean coating is applied to one side only, this is clearly marked with a sticker on the non-coated side. The coated surface is to be fitted inwards towards the inside (wet side) of the screen. Ensure that all surfaces to be sealed are clean and dry prior to applying the silicone sealant. Use a high grade fungal resistant sealant. Allow a minimum of 48 hours after application of the silicone sealant prior to using the screen. TOOLS & MATERIALS REQUIRED Junior Hacksaw Spirit Level 2 x Suction Glass Lifters Straight Edge (Steel Rule) Pencil High Quality Silicone Sealant Fine Tooth File Silicone Gun Tape Measure Set or Roofing Square Power Drill Pozi-drive Screwdrivers, PZ1 & 2 Masking Tape 5.5mm Masonry Drill Bit Safety Glasses & Gloves Modelling Knife CARE AND MAINTENANCE (please ensure that these instructions are left with the installed unit) We recommend routine cleaning of your screen / enclosure with hot water using a soft cloth, then drying with a dry soft cloth or chamois leather. All glass has been treated with EASY CLEAN glass finish and care must be taken to avoid any abrasive cleaning products that may damage the special surface protection. DO NOT use acidic based de-scaler products or products containing bleaches or solvents. Page 2 of 25

3 Supplied Parts Return Panel x 1 Inline Non-Hinge Panel x 1 Door x 1 Inline Hinge Panel x 1 Glass to Glass Hinge x 2 90 Glass to Wall Bracket x 4 90 Glass to Glass Bracket x 2 Door Handle x 1 (Option Dependant) Underframe x 2 Underframe Top x 1 Wall Channel x 2 Spacers 3mm x 6 1mm x 6 Glass to Glass Seal x 1 Glass to Glass Bubble/H Seal x 1 Bottom Door Seal x 1 Page 3 of 25

4 Supplied Parts Rawl Plug & Screw x 6 90 Corner Insert x 1 Square Alignment Jig x 1 Door Support x 2 Page 4 of 25

5 Stay Bar Configuration Options Configuration B SB2 X 2 X 1 X 1 Configuration J SB8 Glass to Wall + Fastener Kit X 2 X 2 X 1 X 1 + Fasteners If no stay bar parts are included - No stay bar is required Page 5 of 25

6 Exploded View These instructions are for left and right handed options. The view below is for a Right Hand Open Out configuration with a SB8 glass to wall Configuration J stay bar. On screens with return panels 1000mm wide or less and inline hinge panels 400mm to 600mm wide, a SB2 Configuration B stay bar is included. On screens with return panels 1000mm or less and inline hinge panels 400mm or less, no stay bar is necessary. You will need to determine which configuration you have and adapt the instructions as appropriate. Page 6 of 25

7 1 Identify the return panel (this is marked on the label on the packaging). Measure the width of the return panel and add 12mm to this measurement, this is the nominal return underframe length. Distance Measured mm +12mm Nominal Return Length = mm 2 Measure the width of the inline panels and the door. Add these measurements together and add 21mm to this measurement, this is the nominal front underframe length. Inline Panel 1 mm + Inline Panel 2 mm + Door mm +21mm Nominal Front Length = mm 3 Lay these measurements out on the shower tray, if being used, or the shower floor if not. We suggest using masking tape where the corner position is to mark onto. Pay attention to the orientation of the underframe. 4 If using a raised shower tray, leave a recommended 3 8mm gap from the edge of the tray. There is a small amount of adjustment (±4mm) from the above marked lengths to allow the gap between the shower tray edge and the outer edge of the underframe pieces to be evened out if required. However, the final underframe length MUST BE within ±4mm of the nominal underframe lengths. IF NOT using a shower tray, use the nominal lengths as the final return and front dimensions for the underframe lengths. Page 7 of 25

8 Select the return panel underframe piece, 5 check you have the correct piece. Measure the final return dimension back from the mitred end (45 end) of the return panel underframe and mark, then carefully cut squarely with a fine toothed Junior Hacksaw. For best results we recommend wrapping some masking tape around the underframe in the area to be cut. Mark this with a Pencil to the correct length then cut, using a fine bladed Junior Hacksaw. Unwrap the tape, and remove any burrs with a fine toothed File, taking care not to scratch or damage the surface finish. Select the front underframe piece. 6 Measure the final front dimension back from the mitred end (45 end) of the front panel underframe and mark, then carefully cut squarely with a fine toothed Junior Hacksaw. Remove any burrs with a fine toothed File, taking care not to scratch or damage the surface finish. 7 Connect the underframe using the 90 underframe connector supplied. You will require a PZ1 size screw driver for this (not included). Underside of Underframe 8 Peel the backing strips from the self-adhesive pads on the underframe and press firmly down into position. Page 8 of 25

9 Insert the 10mm thick Square Alignment Jig to locate the wall channel. Using a 9 Spirit Level ensure that the channel is vertical, mark three holes through the predrilled channel as indicated to attach the channel to the wall. Repeat for the other wall channel. 10 Remove the two wall channels noting their position. Using a 5.5mm high quality masonry drill bit for a clean and precise hole, drill the holes where marked and insert the wall plugs fully. Professional Tip: If drilling ceramic tiles, place masking tape on the tiles before marking and drill through the tape to prevent the drill bit from skidding around. DO NOT use Hammer action as this will crack the tiles. 11 Test fix the wall channels using the screws provided. DO NOT use silicone at this point. Trial fit the return panel. Note the orientation and position of the return panel, this 12 can be determined by the number & size of holes and any attached labels. The return panel is fitted onto 2 stacks of spacers, positioned as shown within the base channel: Start with the 3mm spacers. NOTE, there must be a minimum of one No. 1mm spacer under the return panel. Page 9 of 25

10 Using purpose made Glass Lifters to handle the return panel, carefully insert into the wall channel and lower onto the spacers. The return panel must be inserted squarely into the wall channel and lowered into the base channel. Take great care NOT to knock the corners as this can cause the panel to shatter. To remove the return panel, lift squarely from the base channel and slide out of the wall channel. 20mm Holes this Side WARNING: The glass is heavy and may damage the floor and base channel if handled incorrectly. It is advisable to use a suitable non-slip protective mat to safeguard against damage to the floor (A strip of carpet is ideal). Never place glass across the base channel as this can damage it. 13 Remove and replace the return panel adding or subtracting spacers as necessary to level the panel (to a maximum height of 5mm inside the base channel). Check the return panel is level using a Spirit Level. 14 Loosely assemble the two 90 glass to wall brackets onto the return panel. The face that attaches to the wall should normally be located within the shower screen. DO NOT fit the cover plates yet. 15 Using a Pencil, mark the holes for attaching the 90 glass to wall brackets to the wall. Use a piece of masking tape where the brackets touch the wall to mark onto. Page 10 of 25

11 16 Trial fit the wall side inline panel (the inline hinge panel in this configuration). Note the orientation and position of the wall side inline panel, this can be determined by the number & size of holes and any attached labels. The wall side inline panel is fitted onto 2 stacks of spacers, positioned as shown within the base channel: Start with the 3mm spacers. NOTE, there must be a minimum of one No. 1mm spacer under the wall side inline panel. Using purpose made Glass Lifters to handle the wall side inline panel, carefully lower onto the spacers and slide into the wall channel. The wall side inline panel must be inserted squarely into the underframe and slid into the wall channel. Take great care NOT to knock the corners as this can cause the panel to shatter. To remove the wall side inline panel, slide out of the wall channel and carefully lift out of the underframe. 20mm Holes this Side 17 Remove and replace the inline panel adding or subtracting spacers as necessary to level the panel (to a maximum height of 5mm inside the base channel). Check the return panel is level using a Spirit Level. Loosely assemble the two 90 glass to wall brackets onto the wall side inline 18 panel. The face that attaches to the wall should normally be located within the shower screen. DO NOT fit the cover plates yet. 19 Using a Pencil, mark the holes for attaching the 90 glass to wall brackets to the wall. Use a piece of masking tape where the brackets touch the wall to mark onto. Page 11 of 25

12 Trial fit the return side inline panel. 20 Note the orientation and position of the return side inline panel, this can be determined by the number & size of holes and any attached labels. The return side inline panel is fitted onto 2 stacks of spacers, positioned as shown within the base channel: Start with the 3mm spacers. NOTE, there must be a minimum of one No. 1mm spacer under the return side inline panel. Using purpose made Glass Lifters to handle the return side inline panel, carefully lower onto the spacers and slide up to the return panel. The return side inline panel must be inserted squarely into the underframe and slid carefully up to the return panel. Take great care NOT to knock the corners as this can cause the panel to shatter. To remove the return side inline panel, slide away from the return panel and carefully lift out of the underframe Remove and replace the inline panel adding or subtracting spacers as necessary to level the panel (to a maximum height of 5mm inside the base channel). Check the return panel is level using a Spirit Level. Loosely assemble the 90 glass to glass brackets. Evenly tighten the screws until the gaskets are just nipped. DO NOT fit the cover plates yet. Check that the top of the return panel and the 23 adjacent inline panel are level. This can be done by raising or lowering one of the panels. Ensure that you add or remove spacers equally to raise or lower the panel. Remember not to stack the spacers higher than 5mm. If the difference in height between the panels is greater than 5mm, it may be necessary to lower the original panel before trying to raise the second. Page 12 of 25

13 Check that the top of the two inline panels are level. This can be done by raising or lowering one of the panels. Ensure that you add or remove spacers equally to raise or lower the panel. 24 Remember not to stack the spacers higher than 5mm. If the difference in height between the panels is greater than 5mm, it may be necessary to lower the original panel before trying to raise the second. Using a straight edge mark 25 the wall channels where they need to be trimmed, in line with the top of the respective return and inline panels. We recommend putting a piece of masking tape on the wall channel edge and marking onto this to prevent damage to the wall channel finish. Remove the return panel, inline panels & the wall 26 channels and set the panels safely aside to refit later. Note the position of each respective wall channel. Using a fine toothed Junior Hacksaw, carefully cut the wall channels to the correct 27 length. Ensure that the cuts are square and along the marks made. Carefully use a fine toothed File to remove any burrs and sharp edges, taking care not to scratch or damage the surface finish. 28 Using a 5.5mm high quality masonry drill bit for a clean and precise hole, drill all the marked holes and insert the wall plugs fully. Page 13 of 25

14 Re-attach the wall channels in their previous position, 29 this time using silicone sealant as indicated. Run a bead of silicone sealant along the back face of the wall channels to make a water tight seal to the wall. Again, place the Square Alignment Jig in and ensure the channels are vertical using a Spirit Level. Wipe away any excess sealant that may have squeezed out the side of the channel, to leave a clean finish. 30 Run beads of silicone sealant down the return panel wall channel only, on the inside faces as shown one at a time. DO NOT run too larger beads or fill the channel with silicone. It is VERY IMPORTANT to put a good amount of silicone in the corner where the wall channels meet the return panel underframe. This area needs to be properly sealed to prevent any water leakage. Page 14 of 25

15 31 28 Ensure the spacers are still in place in the return panel underframe. Carefully replace the return panel ensuring it is level. Ensure the front edge of the return panel butts up to the front underframe inside edge with no gap. Re-assemble the 90 glass to wall brackets to the return panel. Evenly tighten the screws until the gaskets are just nipped, then turning each screw a quarter turn at a time, tighten the screws by one full turn. DO NOT fit the cover plates yet. No Gap Ensure the spacers are still in place in the underframe for the return side inline 32 panel. Carefully replace the return side inline panel ensuring it is level and butted squarely up to the return panel with no gap. 33 Loosely assemble the 90 glass to glass brackets. Evenly tighten the screws until the gaskets are just nipped, then turning each screw a quarter turn at a time, tighten the screws by one full turn. DO NOT fit the cover plates yet. 34 Ensure the spacers are still in place in the underframe for the wall side inline panel. Carefully replace the wall side inline panel. Measure the width of the door panel. Add 11mm to this dimension. Set the gap 35 between the two inline panels to this dimension and mark the inner edge of the wall side inline panel on the underframe. This marks where the wall side inline panel needs fitting to, once silicone is applied. We recommend putting a piece of masking tape on the underframe edge and marking onto this to prevent damage to the underframe finish. Remove the wall side inline panel and safely set aside to refit later. Page 15 of 25

16 36 Run beads of silicone sealant down the inline panel wall channel, on the inside faces as shown one at a time. DO NOT run too larger beads or fill the channel with silicone. It is VERY IMPORTANT to put a good amount of silicone in the corner where the wall channel meets the front underframe. This area needs to be properly sealed to prevent any water leakage. Ensure the spacers are still in place in the underframe for the wall side inline panel. Carefully replace the wall side inline panel, aligning the edge to the mark you made earlier: Fix in place with the 90 glass to wall brackets. Evenly tighten the screws until the gaskets are just nipped, then turning each screw a quarter turn at a time, tighten the screws by one full turn. DO NOT fit the cover plates yet Place the door supports over the underframe as shown. With one person inside the screen, position the door onto the door supports. Page 16 of 25

17 39 Add spacers to the door supports in order to level the door. Check that the top of the door is level with the inline panels. If necessary, add or 40 remove spacers equally under the door. The gap between the door and the inline hinge panel should be approximately 5mm, and the gap between the door and the inline non-hinge panel should be 6mm. Page 17 of 25

18 41 Attach the glass to glass hinges and tighten. Evenly tighten the screws until the gaskets are just nipped, then turning each screw a quarter turn at a time, tighten the screws by one full turn. DO NOT fit the cover plates yet. View from Outside 42 If a handle option is included, attach the handle, securing in place with the grub screws supplied. The handle should be oriented so that the grub screws are not visible when looking down at the handle. Page 18 of 25

19 43 Open the door and measure the distance between the inline panels. Mark and squarely cut the underframe top to this dimension. Run two small beads of silicone along the underside of the underframe top and push firmly into position. Outside of Shower Inside of Shower 44 Attach the bottom door seal to the bottom of the door. Check the orientation is correct. Using a fine toothed Junior Hacksaw trim the bottom door seal level with the edges of the door. Inside of Shower Inside of Shower Glass to Glass Seal Glass to Glass Bubble/H Seal Inside of Shower Bottom Door Seal Page 19 of 25

20 45 31 Attach the glass to glass seal to the inline hinge panel so that it butts up to the underframe top. Check the orientation is correct. Using a fine toothed Junior Hacksaw trim the glass to glass seal level with the top of the inline hinge panel. We suggest using a sharp Modelling Knife to cut the softer tail part of the seal. Attach the glass to glass bubble/h seal to the inline non-hinge panel so that it butts up to the underframe top. Check the orientation is correct. Using a fine toothed Junior Hacksaw trim the glass to glass bubble/h seal level with the top of the inline non-hinge panel. We suggest using a sharp Modelling Knife to cut the softer tail and bubble part of the seal. 46 Using a sharp Modelling Knife, trim any excess gasket material from the hinges and brackets that may have squeezed out when tightening. Take care not to scratch the glass surface. Fit the cover plates to the hinges and wall brackets. 47 Check which stay bar configuration your screen has been supplied with (listed towards the front of these instructions) and refer to the relevant instructions below. Stay Bar Configuration B B1 Assemble the stay bar to the glass clamp. Page 20 of 25

21 B2 Secure the glass clamp over the wall side inline panel, ensuring it is also squarely touching the adjacent wall. B3 Ensure that the stay bar is level and square, mark the location of the end of the bar onto the wall. Remove the stay bar and position the stay bar connector central to the line and with a small drill, mark the holes for drilling. Use a piece of masking tape where the stay bar touches the wall to mark onto. B4 Drill a 5.5mm high quality masonry drill bit for a clean and precise hole, drill the holes where marked and insert the wall plugs fully. Screw the stay bar connector to the wall, reassemble the stay bar to the inline panel and securely tighten. Page 21 of 25

22 Stay Bar Configuration J J1 Measure the width of the top of the screen from the inside of the return panel to wall opposite. Ensure that this measurement is truly horizontal. Distance Measured Final Dimension = mm -5mm mm Mark the final dimension on the stay J2 bar from one end. We suggest wrapping a piece of masking tape around the stay bar to make this easier. Carefully cut the stay bar using a fine toothed Junior Hacksaw, taking care to make sure the cut is square. Using a fine toothed File remove any burrs or sharp edges, taking care not to scratch or damage the surface finish. DO NOT discard the off-cut yet. Page 22 of 25

23 J3 To prepare the cut end of the stay bar to take the glass clamp, attach the off-cut to the stay bar with masking tape as shown. Make sure the non-cut end of the off-cut is aligned with the end of the stay bar that you have just cut. Use the Guide holes to drill two 5mm holes through one side of the stay bar only. Be careful NOT to drill through completely. J4 Assemble the stay bar to the glass clamp. J5 Place the two stay bar tee pieces onto the inline panels as shown, aproximately 15mm in from the edge of the inline panels. Door Door Page 23 of 25

24 44 J6 Secure the glass clamp over the return panel making sure it is sitting fully into the two stay bar tee piece grooves. J7 Ensuring that the stay bar is level and square, mark the location of the end of the bar onto the wall. Remove the stay bar and position the stay bar connector central to the line and with a small drill, mark the holes for drilling. Use a piece of masking tape where the stay bar touches the wall to mark onto. J8 Using a 5.5mm high quality masonry drill bit for a clean and precise hole, drill the holes where marked and insert the wall plugs fully. Screw the stay bar connector to the wall, reassemble the stay bar to the return panel and securely tighten all fittings. Page 24 of 25

25 Apply silicone sealant as shown below to where the fixed glass meets the underframe on the inside, between the underframe and the shower tray (or tiles) and the wall channel & wall, inside & out. Run a fillet of silicone sealant down the join between the inline and return panels on the inside (wet side) of the screen. 48 View Outside Wall Channel Inside of Shower View Inside Page 25 of 25

Radon 07 Installation Instructions & Parts List

Radon 07 Installation Instructions & Parts List Radon 07 Installation Instructions & Parts List Illustration Radon 07, H1 Handle Right Hand: Open Out 14/06/2016 Revision 1.1 Page 1 of 21 IMPORTANT This shower screen / enclosure must be installed by

More information

Xenon 05 Installation Instructions & Parts List

Xenon 05 Installation Instructions & Parts List Xenon 05 Installation Instructions & Parts List Illustration Xenon 05, H1 Handle Left Hand: Open Out 26/05/2016 Revision 2.1 Page 1 of 19 IMPORTANT This shower screen / enclosure must be installed by suitably

More information

Gallium 03 Installation Instructions & Parts List

Gallium 03 Installation Instructions & Parts List Gallium 03 Installation Instructions & Parts List Illustration Gallium 03, H1 Handle Left Hand: Open Out 04/05/2016 Revision 1.1 Page 1 of 19 IMPORTANT This shower screen / enclosure must be installed

More information

Curium 19.4H Installation Instructions & Parts List

Curium 19.4H Installation Instructions & Parts List Curium 19.4H Installation Instructions & Parts List Illustration Curium 19.4H Right Hand Page 1 of 21 30/06/2016 Revision 1.0 IMPORTANT This shower screen / enclosure must be installed by suitably qualified

More information

Curium 19H Installation Instructions & Parts List

Curium 19H Installation Instructions & Parts List Curium 19H Installation Instructions & Parts List Illustration Curium 19H Right Hand Page 1 of 15 01/07/2016 Revision 2.1 IMPORTANT This shower screen / enclosure must be installed by suitably qualified

More information

Argon 02 Installation Instructions & Parts List

Argon 02 Installation Instructions & Parts List Argon 02 Installation Instructions & Parts List Illustration Argon, H1 Handle Right Hand: Open Out 16/06/2016 Revision 1.1 Page 1 of 10 IMPORTANT This shower screen / enclosure must be installed by suitably

More information

B A T H R O O M G L A S S

B A T H R O O M G L A S S mistley B A T H R O O M G L A S S vaug16 Page 2 Thank you for purchasing this Trinity shower screen. Please study these instructions carefully before assembly and installation and check all supplied parts

More information

Exploded View PAGE 2 OF 9

Exploded View PAGE 2 OF 9 Argon 02 Exploded View PAGE 2 OF 9 Supplied Parts Underframe Underframe Insert Wall to Glass Hinge Door Handle Door Bottom Seal Hinge Seal Bubble Seal PAGE 3 OF 9 Important Information This shower screen/enclosure

More information

Portofino Installation Guide

Portofino Installation Guide vjul16 (for 17 or 24 mm Surface Wall Profiles) DO NOT ASSEMBLE WITHOUT FULLY READING THESE INSTRUCTIONS Page 2 Thank you for purchasing this Portofino shower enclosure. Please study these instructions

More information

Deauville Installation Guide

Deauville Installation Guide vjul16 (for 17 or 24 mm Surface Wall Profiles) DO NOT ASSEMBLE WITHOUT FULLY READING THESE INSTRUCTIONS Page 2 Thank you for purchasing this Deauville shower enclosure. Please study these instructions

More information

Deauville Installation Guide

Deauville Installation Guide vjul16 (for Recessed Wall Profiles) DO NOT ASSEMBLE WITHOUT FULLY READING THESE INSTRUCTIONS Page 2 Thank you for purchasing this Deauville shower enclosure. Please study these instructions carefully before

More information

Portofino Case2 Installation Guide

Portofino Case2 Installation Guide Portofino Case2 Installation Guide vjun16 (for 17 or 24 mm Surface Wall Profile) DO NOT ASSEMBLE WITHOUT FULLY READING THESE INSTRUCTIONS Page 2 Thank you for purchasing this Portofino Case 2 shower enclosure.

More information

Hinge Door + Side Panel

Hinge Door + Side Panel Hinge Door + Side Panel Instruction Manual KL+ KR Important Information Toughened glass is completely safe for use in our shower enclosures and bath screens; providing our products are installed according

More information

Hinge Door + One Inline Panel

Hinge Door + One Inline Panel inge Door + One Inline Panel Instruction Manual KLD + KL Important Information Toughened glass is completely safe for use in our shower enclosures and bath screens; providing our products are installed

More information

Monaco Installation Guide - Surface Profiles - vjun16

Monaco Installation Guide - Surface Profiles - vjun16 1 Thank you for purchasing this Monaco shower screen. Please study these instructions carefully before assembly and installation. Checking of Parts Parts are listed at the beginning of this guide. Please

More information

INFINITE RANGE - HINGE DOOR

INFINITE RANGE - HINGE DOOR INFINITE RANGE - HINGE DOOR HINGE DOOR + 1 SIDE RETURN PANEL (CORNER) Please read these instructions before installing, as incorrect fitting will invalidate the guarantee-carry out each stage before moving

More information

Wall Profiles 2 Pozi Screwdriver. Wall Profile Covers 4 Sealant. Large Panel and Thin Panel Assemblies Sealant Gun

Wall Profiles 2 Pozi Screwdriver. Wall Profile Covers 4 Sealant. Large Panel and Thin Panel Assemblies Sealant Gun Decem Sliding Door (Corner Fitting) Instruction Manual DXT Important Information Toughened glass is completely safe for use in our shower enclosures and bath screens; providing our products are installed

More information

Cardo DOOR & RETURN SHOWER ENCLOSURE INSTALLATION PLEASE READ THESE INSTRUCTIONS CAREFULLY.

Cardo DOOR & RETURN SHOWER ENCLOSURE INSTALLATION PLEASE READ THESE INSTRUCTIONS CAREFULLY. Cardo DOOR & RETURN SHOWER ENCLOSURE INSTALLATION PLEASE READ THESE INSTRUCTIONS CAREFULLY. IT IS RECOMMENDED TO USE A TRAINED SHOWER INSTALLER FOR THIS SHOWER TO OBTAIN THE BEST INSTALLATION. D Square

More information

Installation Instructions

Installation Instructions Installation Instructions Alcove Enclosure Before Installation please check that your shower enclosure system is undamaged Please read these instructions carefully March 2015 TOOLS REQUIRED Electric or

More information

Allora ALCOVE ENCLOSURE INSTALLATION BEFORE INSTALLATION CHECK THAT YOUR ALLORA SHOWER ENCLOSURE SYSTEM IS UNDAMAGED

Allora ALCOVE ENCLOSURE INSTALLATION BEFORE INSTALLATION CHECK THAT YOUR ALLORA SHOWER ENCLOSURE SYSTEM IS UNDAMAGED Allora ALCOVE ENCLOSURE INSTALLATION BEFORE INSTALLATION CHECK THAT YOUR ALLORA SHOWER ENCLOSURE SYSTEM IS UNDAMAGED ALCOVE SHOWER Your shower can be installed to open Left hand or Right hand by rotating

More information

mistley PELE Installation Guide vapr16 Mistley Bathroom Glass Limited No 4 One Mistley Quayside, High Street, Mistley, Essex CO11 1AL England

mistley PELE Installation Guide vapr16 Mistley Bathroom Glass Limited No 4 One Mistley Quayside, High Street, Mistley, Essex CO11 1AL England mistley BAT HRO O M G LASS vapr16 Page 2 Thank you for purchasing this Pele shower screen. Please study these instructions carefully before assembly and installation and check all supplied parts immediately

More information

Hinge Door + Inline Panel + Return Panel

Hinge Door + Inline Panel + Return Panel Hinge Door + Inline Panel + Return Panel Instruction Manual DXL2HDR + DXL2HR + DXR Important Information Toughened glass is completely safe for use in our shower enclosures and bath screens; providing

More information

Installation Site Preparation - Site Preparation

Installation Site Preparation - Site Preparation S c u l p t u r e s Bespoke Single Door / Bespoke Frameless Hinged Door + Inline Panel Instruction Manual Truelife Consumer Guarantee Please make sure the purchaser/end user completes and returns the Guarantee

More information

Frameless Inline Door With Return QCI5263

Frameless Inline Door With Return QCI5263 INSTALLATION INSTRUCTIONS Frameless Inline Door With Return QCI5263 WALL MOUNT HINGES FRAMELESS DOOR / PANEL / RETURN PANEL QCI5263 REV. 0 Page 1 Certified 06/17/2016 Parts List with wall mount hinges

More information

INFINITE RANGE - CENTRE FOLDING DOOR

INFINITE RANGE - CENTRE FOLDING DOOR INFINITE RANGE - CENTRE FOLDING DOOR CENTRE FOLDING DOOR ONLY ( RECESS) Please read these instructions before installing, as incorrect fitting will invalidate the guarantee-carry out each stage before

More information

Frameless Inline Door QCI5254

Frameless Inline Door QCI5254 INSTALLATION INSTRUCTIONS Frameless Inline Door QCI5254 FRAMELESS DOOR / PANEL QCI5254 REV. 0 Page 1 Cer fied 06/16/2016 Parts List with wall mount hinges *Quanes may vary QCI5254 REV. 0 Page 2 Cer fied

More information

tile redi redi DOOR Redi Redi Swing Slide g TM TM...Opening Doors to Stunning Showers! TM TM SERIES: CONFIGURATION: MOUNTING PACKAGE:

tile redi redi DOOR Redi Redi Swing Slide g TM TM...Opening Doors to Stunning Showers! TM TM SERIES: CONFIGURATION: MOUNTING PACKAGE: redi DOOR INSTALLATION INSTRUCTIONS tile redi Redi Redi Swing Slide g TM TM...Opening Doors to Stunning Showers! TM TM SERIES: CONFIGURATION: MOUNTING PACKAGE: 3000 Door-Door Header, sliding doors RDQCI5301

More information

SLIDING DOOR for CORNER installation ONLY - this door closes to side panel -

SLIDING DOOR for CORNER installation ONLY - this door closes to side panel - by KUDOS INSTALLATION INSTRUCTIONS SLIDING DOOR for CORNER installation ONLY - this door closes to side panel - Please read these instructions throughout before installing as incorrect fitting will invalidate

More information

ALLORA SWING PANEL INSTALLATION INSTRUCTIONS

ALLORA SWING PANEL INSTALLATION INSTRUCTIONS ALLORA SWING PANEL INSTALLATION INSTRUCTIONS Before Installation Please check that your Allora Swing Panel is undamaged SEQUENCE OF INSTALLATION These instructions are also available from the Athena website:

More information

Monaco Installation Guide - Surface Profiles

Monaco Installation Guide - Surface Profiles v1 Page 1 Thank you for purchasing this Monaco shower screen. Please study these instructions carefully before assembly and installation and check all supplied parts immediately upon receipt. These instructions

More information

CORNER ENTRY ENCLOSURE

CORNER ENTRY ENCLOSURE CORNER ENTRY ENCLOSURE SUPREME INSTALLATION INSTRUCTIONS IMPORTANT - Please read before installation Please read these instructions carefully before starting installation and keep in a safe place for future

More information

Centre-fold Door. Installation Instructions. Please note: Images shown are for illustration purposes only

Centre-fold Door. Installation Instructions. Please note: Images shown are for illustration purposes only Centre-fold Door Installation Instructions Please note: Images shown are for illustration purposes only Please read these instructions in full before installing. The enclosure can be installed to give

More information

Frameless Bypass Slider

Frameless Bypass Slider INSTALLATION INSTRUCTIONS Frameless Bypass Slider QCI-5301 Heavy Glass Bypass Slider with Exposed Rollers QCI5301 Rev 0 Page 1 Certified 11/1/2016 Tools: To install your New Shower Enclosure, you may need

More information

Frameless Inline Door QCI5248

Frameless Inline Door QCI5248 INSTALLATION INSTRUCTIONS Frameless Inline Door QCI5248 FRAMELESS PANEL / DOOR / PANEL QCI5248 REV. 0 Page 1 Certified 06/16/2016 Parts List with glass to glass hinges *Quantities may vary. **Support Bar

More information

Slider Door Installation Instructions

Slider Door Installation Instructions Slider Door Installation Instructions IMPORTANT: If installing a Slider Door and Side Panel only; ie. a corner installation, please refer to alternative fixing details on the document reverse. 2 YEAR GUARANTEE

More information

FRAMELESS DOOR / PANEL WITH WALL MOUNT HINGES QCI5274

FRAMELESS DOOR / PANEL WITH WALL MOUNT HINGES QCI5274 FRAMELESS DOOR / PANEL WITH WALL MOUNT HINGES QCI5274 QCI0274 QCI5274 REV. Rev. 1 0 Page Page 1 1 Date Certified: Certified 06/16/2016 10/01/10 Parts List with wall mount hinges ITEM NO. Part # DESCRIPTION

More information

Frameless Bypass Slider

Frameless Bypass Slider INSTALLATION INSTRUCTIONS Frameless Bypass Slider QCI-5301 3/8 or 1/4 Glass Bypass Slider with Exposed Rollers QCI5301 Rev 1 Page 1 Certified 6/5/2017 Tools: To install your New Shower Enclosure, you may

More information

Shower Screen and Door Kit Instructions

Shower Screen and Door Kit Instructions Shower Screen and Door Kit Instructions Step by step guide everton.com.au IMPORTANT NOTICE IMPORTANT: The glass panels used for Highrove frameless shower screens are made from Grade A Toughened Safety

More information

FIXED PANEL SLIDER QCI5241

FIXED PANEL SLIDER QCI5241 INSTALLATION INSTRUCTIONS FIXED PANEL SLIDER QCI5241 FRAMELESS PANEL / DOOR / PANEL FRAMELESS DOOR / PANEL QCI5241 REV. 0 Page 1 Certified 06/16/2016 Parts List *Quantities may vary QCI5241 REV. 0 Page

More information

Double Frameless Swing Door QCI5247

Double Frameless Swing Door QCI5247 INSTALLATION INSTRUCTIONS Double Frameless Swing Door QCI5247 WALL MOUNT HINGES QCI5247 REV. 0 Page 1 Certified 06/16/2016 Parts List with wall mount hinges *Quantities may vary **Quantities double where

More information

INFINITE RANGE - CENTRE FOLDING DOOR

INFINITE RANGE - CENTRE FOLDING DOOR INFINITE RANGE - CENTRE FOLDING DOOR CENTRE FOLDING DOOR + 2 SIDE RETURN PANELS (PENINSULA) Please read these instructions before installing, as incorrect fitting will invalidate the guarantee-carry out

More information

ELEGANCE SHOWER DOOR/ENCLOSURE INSTALLATION INSTRUCTIONS. Style A Style B Style C Style D

ELEGANCE SHOWER DOOR/ENCLOSURE INSTALLATION INSTRUCTIONS. Style A Style B Style C Style D ELEGANCE SHOWER DOOR/ENCLOSURE INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical

More information

Platinum Swing Panel Installation Instructions

Platinum Swing Panel Installation Instructions Platinum Swing Panel Installation Instructions The Standard Platinum Swing Panel is designed to fit baths with a perimeter lip no taller than 20mm. If installing onto baths without a perimeter lip an optional

More information

Bi-fold Door Installation Instructions

Bi-fold Door Installation Instructions Bi-fold Door Installation Instructions IMPORTANT: If installing a Pivot Door and Side Panel, ie. a corner installation, please refer to alternative fixing details on the document reverse. 2 YEAR GUARANTEE

More information

Frameless Hinged Door Enclosure. These instructions must be left with the user. Installation Guide W2-B

Frameless Hinged Door Enclosure. These instructions must be left with the user. Installation Guide W2-B Frameless Hinged Door Enclosure These instructions must be left with the user Installation Guide 1 1290643-W2-B 1290643-W2-B 2 Introduction Thank you for purchasing a quality product. To enjoy the full

More information

Frameless Door QCI5284

Frameless Door QCI5284 Frameless Door QCI5284 F AB GLASS AND MIRROR www.fabglassandmirror.com Call: +1 888-474-2221 Fax: (614)-334-4919 Office Timing: 8:30-18:00 EST info@fabglassandmirror.com INSTALLATION INSTRUCTIONS Frameless

More information

Installation Instructions

Installation Instructions Installation Instructions Angle orner & Round Enclosures efore Installation please check that your shower enclosure system is undamaged Please read these instructions carefully Oct 2015 TOOLS REQUIRE Electric

More information

Modular Shower Panel. IN00580 (Iss 1)

Modular Shower Panel. IN00580 (Iss 1) IN00580 (Iss 1) Modular Shower Panel Instruction suitable for both Right and Left Hand fixing variations. Instruction suitable for both Tray and Wetfloor fixing variations. Before You Start - Tray Fix

More information

Installation Instructions

Installation Instructions Installation Instructions Walk-in Shower Screen with 180 o Return Panel (700 + 350mm & 900 + 350mm) Installation Instructions Parts supplied A B C D Wall Channel (x1) Wall fixing screw (x6) Return Straight

More information

Thank you for your order

Thank you for your order Installation Guide Thank you for your order Ph: 09-9133110 Fax: 09-9133113 5 Smales Road. East Tamaki, Manukau PO Box 58031 Greenmount, Manukau 2013 AUCKLAND // WELLINGTON // CHRISTCHURCH www.bathroomdirect.co.nz

More information

Frameless Heavy Glass Door with Wall Mount Hinges

Frameless Heavy Glass Door with Wall Mount Hinges INSTALLATION INSTRUCTIONS Frameless Heavy Glass Door with Wall Mount Hinges QCI-5245 QCI5245 REV. 0 Page 1 Certified 06/16/16 Frameless Door with Wall Mount Hinges ITEM NUMBER DESCRIPTION QUANTITY 1 DOOR

More information

IMPORTANT - GLASS IS FRAGILE AND CAN SHATTER.

IMPORTANT - GLASS IS FRAGILE AND CAN SHATTER. STEP BY STEP SHOWER SCREEN INSTALLATION GUIDE IMPORTANT - GLASS IS FRAGILE AND CAN SHATTER. 2 PEOPLE ARE IMPORTANT REQUIRED - GLASS FOR GLASS IS FRAGILE PANEL AND INSTALLATION CAN SHATTER. TO AVOID GLASS

More information

Frameless Inline Door QCI5250

Frameless Inline Door QCI5250 INSTALLATION INSTRUCTIONS Frameless Inline Door QCI5250 FRAMELESS PANEL / DOOR / PANEL QCI0249 REV. 3 Page 1 Certified 10/12/12 Parts List with pivot hinges *Quantities may vary. QCI0249 REV. 3 Page 2

More information

Two Panel Frameless Bypass Door

Two Panel Frameless Bypass Door INSTALLATION INSTRUCTIONS Two Frameless Bypass Door Series 00 Please Record Model Number From Carton Label Here Please read these instructions carefully to familiarize yourself with the required tools,

More information

Panel Riser Kit Option 1. Installation Instructions 226BEE 0117CH

Panel Riser Kit Option 1. Installation Instructions 226BEE 0117CH Panel Riser Kit Option 1 Installation Instructions 226BEE 0117CH Before you Start Please read these instructions fully before starting. Although these instructions are comprehensive we always recommend

More information

FIXED SHOWER SCREEN For Wall Mount Hinges QCI5283

FIXED SHOWER SCREEN For Wall Mount Hinges QCI5283 FIXED SHOWER SCREEN For Wall Mount Hinges QCI5283 QCI5283 Page 1 Date Certified: 06/16/2016 Parts List with wall mount clamp ITEM NO. DESCRIPTION QTY. 1 FIXED GLASS PANEL 1 2 WALL MOUNT CLAMP 1 3 U-CHANNEL

More information

A-935 RODA WALL MOUNT HINGES

A-935 RODA WALL MOUNT HINGES INSTALLATION INSTRUCTIONS A-935 RODA WALL MOUNT HINGES NEED INSTALLATION HELP? Call 1-800-45-BASCO (452-2726) Monday - Friday 8:00 A.M. - 4:30 P.M. Eastern Time FRAMELESS DOOR / PANEL CELESTA QCI0274 REV.

More information

Frameless Inline Door QCI5288

Frameless Inline Door QCI5288 Frameless Inline Door QCI5288 QCI5288 Rev. 0 Page 1 Date Certified: 06/21/2016 Tools: To install your New Shower Enclosure, you may need the following: Pencil Drill Hack Saw Low Tack Tape 1/8 & 3/16 Drill

More information

SHOWER SCREEN INSTALLATION GUIDE WET ROOMS MADE EASY

SHOWER SCREEN INSTALLATION GUIDE WET ROOMS MADE EASY SHOWER SCREEN INSTALLATION GUIDE WET ROOMS MADE EASY IMPORTANT INFORMATION TOOLS & PARTS REQUIRED Please read these instructions carefully before starting installation and keep for future reference. Remove

More information

Frameless Fixed Panel Slider

Frameless Fixed Panel Slider INSTALLATION INSTRUCTIONS Frameless Fixed Panel Slider QCI-5279 SINGLE ROLLER WITH ANTI-JUMP DOUBLE ROLLERS QCI5279 Rev Page Certified 08/09/6 Tools: To install your New Shower Enclosure, you may need

More information

UNIDOOR (STYLES B&C)

UNIDOOR (STYLES B&C) UNIDOOR (STYLES B&C) SHOWER DOOR & GLASS PANEL INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date

More information

SERIES: CONFIGURATION: MOUNTING PACKAGE: 1200 Door-Door Frameless, sliding door

SERIES: CONFIGURATION: MOUNTING PACKAGE: 1200 Door-Door Frameless, sliding door SERIES: CONFIGURATION: MOUNTING PACKAGE: 1200 Door-Door Frameless, sliding door RDQCI5022 Rev.0 Page 1 Certified 06/01/2016 Tools: To install your New Shower Enclosure, you may need the following: Pencil

More information

tile redi redi DOOR Redi Redi Swing Slide g TM TM...Opening Doors to Stunning Showers! TM TM SERIES: CONFIGURATION: MOUNTING PACKAGE:

tile redi redi DOOR Redi Redi Swing Slide g TM TM...Opening Doors to Stunning Showers! TM TM SERIES: CONFIGURATION: MOUNTING PACKAGE: redi DOOR INSTALLATION INSTRUCTIONS tile redi Redi Redi Swing Slide g TM TM...Opening Doors to Stunning Showers! TM TM SERIES: CONFIGURATION: MOUNTING PACKAGE: 1100 Door-Door Framed sliding doors RDQCI5023

More information

Frameless Fixed Panel Slider QCI5279

Frameless Fixed Panel Slider QCI5279 Frameless Fixed Panel Slider QCI5279 F AB GLASS AND MIRROR www.fabglassandmirror.com Call: +1 888-474-2221 Fax: (614)-334-4919 Office Timing: 8:30-18:00 EST info@fabglassandmirror.com Frameless Fixed Panel

More information

UNIDOOR-X TUB DOOR TUB DOOR INSTALLATION NSTRUCTIONS. MODEL #s D58580-##

UNIDOOR-X TUB DOOR TUB DOOR INSTALLATION NSTRUCTIONS. MODEL #s D58580-## T F UNIDOOR-X TUB DOOR se A R a e l re TUB DOOR INSTALLATION I NSTRUCTIONS r o D ved f IMPORTANT DreamLine reserves the right to alter, modify or redesign products at any time without prior notice. For

More information

WETROOM WALK-IN TWIN ENTRANCE AWT1500 AWT1200 AWT900

WETROOM WALK-IN TWIN ENTRANCE AWT1500 AWT1200 AWT900 WETROOM WALK-IN TWIN ENTRANCE AWT500 AWT00 AWT900 INSTALLATION PARTS LIST 5 AF /6 IMPORTANT Before disposing of carton and/or commencing assembly, please check all the parts to ascertain that none are

More information

ENIGMA AIR ENCLOSURE

ENIGMA AIR ENCLOSURE ENIGMA AIR ENCLOSURE SHOWER ENCLOSURE INSTALLATION INSTRUCTION IMPORTANT DreamLine reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical

More information

INSTALLATION INSTRUCTIONS DANUBE ACRYLIC NEO ANGLE

INSTALLATION INSTRUCTIONS DANUBE ACRYLIC NEO ANGLE INSTALLATION INSTRUCTIONS DANUBE ACRYLIC NEO ANGLE March 2013 DOOR 2 Page 1 of 5 INSTALLATION INSTRUCTIONS NEO ANGLE 6MM FRAMELESS AND 4MM FRAMED SHOWER DOOR DANUBE, DELTA, SIGNATURE, OCEANIA, CASCADE

More information

Installation Instructions

Installation Instructions Installation Instructions Bespoke Glass Design In A Box Typical Installation Guidance Installation Instructions Important Information Please read these instructions carefully before starting installation

More information

SHOWER ENCLOSURE INSTALLATION

SHOWER ENCLOSURE INSTALLATION T F e34 x 46 s a QUATRA LUX 32 x 46 / ele A R r r fo SHOWER ENCLOSURE INSTALLATION I NSTRUCTIONS d e D v o r p IMPORTANT DreamLine reserves the right to alter, modify or redesign products at any time without

More information

INSTALLATION INSTRUCTIONS FRAMELESS CONTINUOUS HINGE SHOWER ENCLOSURE QCI5233

INSTALLATION INSTRUCTIONS FRAMELESS CONTINUOUS HINGE SHOWER ENCLOSURE QCI5233 INSTALLATION INSTRUCTIONS FRAMELESS CONTINUOUS HINGE SHOWER ENCLOSURE QCI5233 QCI5233 Rev 0 Page 1 Certified 06/20/2016 INSTALLATION NOTES: Unpack your unit carefully and inspect for freight damage. Lay

More information

tile redi redi DOOR Redi Swing SERIES: CONFIGURATION: MOUNTING PACKAGE:

tile redi redi DOOR Redi Swing SERIES: CONFIGURATION: MOUNTING PACKAGE: redi DOOR INSTALLATION INSTRUCTIONS tile redi Redi Swing g TM TM...Opening Doors to Stunning Showers! TM TM SERIES: CONFIGURATION: MOUNTING PACKAGE: 2900V Door-Panel No header, offset pivot hinges, u-channel

More information

IMPORTANT: If installing a Glide Bifold Door only; ie. a recess installation, please refer to alternative fixing details on the document reverse.

IMPORTANT: If installing a Glide Bifold Door only; ie. a recess installation, please refer to alternative fixing details on the document reverse. IN00422 (rev A) Aqua 6 / Aqua 8 Glide Bifold Door & Side Panel Instruction suitable for both Right and Left Hand fixing variations. IMPORTANT: If installing a Glide Bifold Door only; ie. a recess installation,

More information

Solutions. Installation Instructions. Ref Description Illustration Qty. A Shower Tray* mm Radius Curved Panel* Universal. Curved Quad Panel*

Solutions. Installation Instructions. Ref Description Illustration Qty. A Shower Tray* mm Radius Curved Panel* Universal. Curved Quad Panel* Solutions Parts Supplied Installation Instructions Ref Description Illustration ty Shower Tray* *Shape of tray may vary from illustration B 550mm Radius Curved Panel* *If your tray is uadrant you will

More information

UNIDOOR (STYLE B & C)

UNIDOOR (STYLE B & C) UNIDOOR (STYLE B & C) SHOWER DOOR GLASS PANEL INSTALLATION INSTRUCTIONS IMPORTANT DreamLine TM reserves the right to alter, modify or redesign products at any time without prior notice. For the latest

More information

Aluminum Clad Wood Window 1/2 Reinforced Field Mulling and Stacking Supplement

Aluminum Clad Wood Window 1/2 Reinforced Field Mulling and Stacking Supplement Aluminum Clad Wood Window 1/2 Reinforced Field Mulling and Stacking Supplement 1 Aluminum Clad Wood Window 1/2 Reinforced Field Mulling and Stacking Supplement The following instructions are a supplement

More information

Series----SP3600A SHOWER DOOR

Series----SP3600A SHOWER DOOR Series----SP3600A SHOWER DOOR INSTALLATION INSTRUCTIONS Please read these instructions carefully to familiarize yourself with the required tools, materials, and installation sequences. The Exploded Diagram

More information

300C6 CONTINUOUS HINGE SEMI-FRAMELESS DOOR KIT

300C6 CONTINUOUS HINGE SEMI-FRAMELESS DOOR KIT 300C6 CONTINUOUS HINGE SEMI-FRAMELESS DOOR KIT LIMITED WARRANTY AND REMEDY Alumax Bath Enclosures warrants to its dealers, customers, and all subsequent purchasers and users, that the products supplied

More information

UNIDOOR X (STYLE L1)

UNIDOOR X (STYLE L1) UNIDOOR X (STYLE L) SHOWER DOOR & GLASS PANEL INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS BUILDERS CHOICE FRAMED Bypass Door Model: L0516 (Tub Height), L0517 (Shower Height) Rev. 09.20.13 INSTALLATION NOTES: Unpack your unit carefully and inspect for freight damage.

More information

INSTALLATION INSTRUCTIONS 960 RODA GLASS TO GLASS HINGES ANGLED FRAMELESS PANEL / DOOR / PANEL CELESTA DRESDEN TRESOR

INSTALLATION INSTRUCTIONS 960 RODA GLASS TO GLASS HINGES ANGLED FRAMELESS PANEL / DOOR / PANEL CELESTA DRESDEN TRESOR INSTALLATION INSTRUCTIONS 960 RODA GLASS TO GLASS HINGES NEED INSTALLATION HELP? Call 1-800-45-BASCO (452-2726) Monday - Friday 8:00 A.M. - 4:30 P.M. Eastern Time ANGLED FRAMELESS PANEL / DOOR / PANEL

More information

Cleaning. This instruction will cover installation of the following units Codes:

Cleaning. This instruction will cover installation of the following units Codes: Cleaning *** All chrome surfaces should be cleaned using a clean damp cloth. *** No abrasive cleaning agents or materials should be used. *** General glass cleaner can be used for the screen, but ensure

More information

UNIDOOR LUX (STYLE E)

UNIDOOR LUX (STYLE E) UNIDOOR LUX (STYLE E) SHOWER DOOR & GLASS PANEL INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date

More information

UNIDOOR/UNIDOORLUX/UNIDOOR PLUS

UNIDOOR/UNIDOORLUX/UNIDOOR PLUS UNIDOOR/UNIDOORLUX/UNIDOOR PLUS SINGLE SHOWER DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter, modify or redesign products at any time without prior notice. For the latest

More information

*** All chrome surfaces should be cleaned using a clean damp cloth. *** No abrasive cleaning agents or materials should be used.

*** All chrome surfaces should be cleaned using a clean damp cloth. *** No abrasive cleaning agents or materials should be used. Cleaning *** All chrome surfaces should be cleaned using a clean damp cloth. *** No abrasive cleaning agents or materials should be used. *** No chemical cleaners can be used on the glass use only mild

More information

Model 5400H / 7000H Illustrated Installation Instructions

Model 5400H / 7000H Illustrated Installation Instructions Model 5400H / 7000H Illustrated Installation Instructions Contractors Wardrobe DESIGNERS MANUFACTURERS 261 Avenue Hall Valencia, CA 91355 (661) 257-1177 (661) 257-4907 TOLL FREE: (800) CW-DOORS (800) 293-6677

More information

PREMIER PENTAGON SHOWER ENCLOSURE

PREMIER PENTAGON SHOWER ENCLOSURE PREMIER PENTAGON SHOWER ENCLOSURE 71677 00 / Issue 1 / 13 SAFETY Please read these instructions carefully and keep for future reference. Incorrect fitting will invalidate the guarantee. Handle glass with

More information

Please read these instructions throughout before installing as incorrect fitting will invalidate the guarantee.

Please read these instructions throughout before installing as incorrect fitting will invalidate the guarantee. by KUDOS INSTALLATION INSTRUCTIONS SLIDING DOOR for RECESS installation ONLY Please read these instructions throughout before installing as incorrect fitting will invalidate the guarantee. If you are unsure

More information

MIRAGE-X / BELLA. Shower Door Installation Instructions

MIRAGE-X / BELLA. Shower Door Installation Instructions MIRAGE-X / BELLA Shower Door Installation Instructions IMPORTANT DreamLine reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical

More information

SHOWER DOOR INSTALLATION & CARE GUIDE

SHOWER DOOR INSTALLATION & CARE GUIDE SHOWER DOOR INSTALLATION & CARE GUIDE For models: SD-AZ-0 Please Note: This is a two person job. The glass doors are extremely heavy and it is highly recommended to use professional installers. For any

More information

QUADRANT SHOWER ENCLOSURE

QUADRANT SHOWER ENCLOSURE QUADRANT SHOWER ENCLOSURE GB 71810 00 / Issue 1 / 15 DIMENSIONS Check the enclosure size in the table below matches the showertray installation. 800 Door X = 780-800mm 900 Door X = 880-900mm X X Please

More information

340 & 350 SERIES BATH ENCLOSURES

340 & 350 SERIES BATH ENCLOSURES INSTALLATION INSTRUCTIONS 340 & 350 SERIES BATH ENCLOSURES 800-643-1514 www.alumaxbath.com Copyright Alumax Bath Enclosures 2010. All rights reserved. LIMITED WARRANTY AND REMEDY ALUMAX BATH ENCLOSURES

More information

VITREO X SHOWER / TUB DOOR INSTALLATION INSTRUCTIONS

VITREO X SHOWER / TUB DOOR INSTALLATION INSTRUCTIONS VITREO X SHOWER / TUB DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings,

More information

Please read these instructions before use and keep for future reference

Please read these instructions before use and keep for future reference Wardrobe Assembly Guide Allen Key Provided (if required) Philips Screwdriver Required Hammer Required Please read these instructions before use and keep for future reference Caution! Two Person Assembly

More information

SHOWER ENCLOSURES INSTALLATION INSTRUCTIONS SHOWER ENCLOSURES:

SHOWER ENCLOSURES INSTALLATION INSTRUCTIONS SHOWER ENCLOSURES: D SHOWER ENCLOSURES INSTALLATION INSTRUCTIONS SHOWER ENCLOSURES: LBSDD4879-C+LBSED3679-CB LBSDD4879-B+LBSED3679-CB LBSDD6079-C+LBSED3679-CB LBSDD6079-B+LBSED3679-CB LBSDD7279-C+LBSED3679-CB LBSDD7279-B+LBSED3679-CB

More information

INSTALLATION INSTRUCTIONS 935 RODA GLASS TO GLASS HINGES FRAMELESS DOOR / PANEL CELESTA DRESDEN GEOLUX TRESOR VONSE

INSTALLATION INSTRUCTIONS 935 RODA GLASS TO GLASS HINGES FRAMELESS DOOR / PANEL CELESTA DRESDEN GEOLUX TRESOR VONSE INSTALLATION INSTRUCTIONS 935 RODA GLASS TO GLASS HINGES NEED INSTALLATION HELP? Call 1-800-45-BASCO (452-2726) Monday - Friday 8:00 A.M. - 4:30 P.M. Eastern Time FRAMELESS DOOR / PANEL CELESTA DRESDEN

More information

ProLine PL60 HEAVY FRAMELESS BYPASS BATH ENCLOSURE

ProLine PL60 HEAVY FRAMELESS BYPASS BATH ENCLOSURE INSTALLATION INSTRUCTIONS ProLine PL60 HEAVY FRAMELESS BYPASS BATH ENCLOSURE Copyright Alumax Bath Enclosures 2013. All rights reserved. G03980847 5-1-13 !WARNINGS! INSTALLATION WARNINGS a) Alumax Bath

More information

COMPONENTS AND BOX CONTENTS

COMPONENTS AND BOX CONTENTS Hinge Hinge Door Door COMPONENTS AND BOX CONTENTS 1 1 2 3 4 5 6 7 8 9 13 10 14 11 12 No. Description Qty Part No. 1 Wall profile cover caps screw 4 8S410045 2 Upright profile cover cap 2 8SSJ035L/R 3 Wall

More information

340 & 350 SERIES DELUXE FRAMELESS BYPASS

340 & 350 SERIES DELUXE FRAMELESS BYPASS BATH ENCLOSURES An Alcoa Company Tel: 800-643-1514 Fax: 870-234-3181 www.alumaxbath.com INSTALLATION INSTRUCTIONS 340 & 350 SERIES DELUXE FRAMELESS BYPASS BATH ENCLOSURES Copyright Alumax Bath Enclosures

More information

340D & 350D SERIES FRAMELESS BYPASS BATH ENCLOSURES

340D & 350D SERIES FRAMELESS BYPASS BATH ENCLOSURES INSTALLATION INSTRUCTIONS 340D & 350D SERIES FRAMELESS BYPASS BATH ENCLOSURES 800-643-1514 www.alumaxshowerdoor.com Copyright Alumax Bath Enclosures 2014. All rights reserved. !WARNINGS! INSTALLATION WARNINGS

More information