VALENCIA CORNER DOOR WITH RETURN

Transcription

1 VALENCIA CORNER DOOR WITH RETURN INSTALLATION GUIDE SEALANT REQUIRED TO COMPLETE THIS INSTALLATION: ( not supplied) Sika Silaflex NG To seal the WHITE shower door and returns to the shower tray. Usage: 1 cartridge per shower Sika Silaflex RTV + Primer Pen To seal the METALLIC shower door and returns to the shower tray. Usage: 1 cartridge per shower 1 primer pen per shower TOOLS REQUIRED Level Tape Pencil Phillips screwdriver Ruler Drill Caulking gun -1- READ ALL INSTRUCTIONS CAREFULLY BEFORE STARTING THE INSTALLATION THIS WILL ENSURE YOU OBTAIN THE BEST POSSIBLE RESULTS

2 -2-

3 Fitting Instructions NOTE: SHOWER TRAY MUST BE INSTALLED AS DETAILED ON SHOWER TRAY CARTON -3-

4 1 Ensure framework is constructed as detailed on shower tray carton. Check that the shower base is level. It is recommended that the waste outlet be taped over to avoid the lose of any components during installation. 3 Check vertical with spirit level and mark fixing holes. ENSURE WALL RETAINER PRO- FILES ARE PLUMB. Select preferred shower door 5 opening. DIMENSION A 2 Position Wall Retainer Profiles against shower walls resting on the shower base sill with fixing holes towards the inside of the shower. Measure from the tile/duracyl wall surface as shown. A A 4 Mark both 45 O corners of shower base and try to ensure, where possible, an even gap between door returns and edges of the tray. If the construction walls are out of square more than 6mm, either direction (in/out), this gap might vary. 6 Fix both wall retainers in place using the 6 long screws. Make sure the screws go into studs. Note: If Screwing into backing board only, use appropriate wall anchors in the wall. CAUTION: We recommend fixing the wall retainers by screwing through the backing board and into studs. Other methods may cause warping and might void warranty. CAUTION: BEFORE DRILLING HOLES, ENSURE THERE ARE NO ELECTRICAL CABLES OR WATER PIPES BEHIND WALLS TYPE DIMENSION A mm mm -4-

5 7 Insert return panel into wall retainer so that the black mark aligns with the edge of the wall retainer. NB: The markings on the top & bottom rails should be on the outside of the enclosure & the flexible side of the PVC gasket on the inside. DO NOT push the PVC gasket into position at this stage. Ensure that the end of this seal just clears the Door Jamb as the door closes to create the best seal. WHERE USED RAISED MODESTY LINE PATTERN MUST FACE OUTSIDE OF SHOWER ENCLOSURE Fit Door Assembly into 45 O Corner 8 Posts and push together. 10 Fit top and bottom hinge caps. (Note bottom cap has Slide drip edge seal over wing 11 on bottom hinge cover and trim off at edge of glass. Repeat between hinge cover and extrusion fixed to 12 Prise drip edge seal off glass beside door edge extrusion enough to slip drip seal moulding underneath. (Note drip seal moulding and retainer bracket are handed.) Push drip seal firmly back onto glass and pull into contact with door edge extrusion. Clamp in place using the bracket and No. 6 screw. Fit the other small screw to the top hole in the door edge extrusion. SFit the handles following instructions that come with the handle pack. 9a Centralise Door Assembly between Wall Retainer and Corner Post. Position Return Panel b between Wall Retainer and Corner Post so that the black lines at each corner are not visible. DO NOT push the PVC gasket into position at this stage. -5-

6 13 Using spirit level, plumb Door, Return panels and 45 O Corner Posts. Tape into position as shown (tape not supplied). Check Door opens and shuts properly and the black lines on the Return assembly top and bottom rails remain hidden. Readjust if necessary. NOTE: This is an important part of the installation procedure and your careful attention at this stage will ensure that you will obtain the best possible results. TEST THE OPENING AND CLOSING OPERATION OF THE PIVOT DOOR If door alignment is incorrect, door will not function properly and further adjustments are necessary. Remove tape and re-align until correct alignment is achieved. DO NOT PROCEED TO STEP 16 UNTIL DOOR IS OPERATING CORRECTLY. 15 Drill holes (with 2.5mm drill bit, DO NOT USE BIGGER DRILL BIT) through punched holes at top and bottom of each Wall Retainer and Corner Post to secure door and return. Make sure Door and Return assemblies do not move during this operation. Fit screw, screw caps and remove tape. RETURN WALL RETAINER O CORNER POST Position Return Panel PVC gasket by pushing outside leg into both Wall Retainers and Corner Posts. It should snap into place. Now push the inside leg into place. Inside Shower Outside Shower Push outside leg Push inside leg 14 Remove screws from corner of door at each 45 O post in turn and fit corner brackets. Fit screw into top of Return Panel as shown. 6g x 3 /8 screw Fit handles following instruction 17 with handles. -6-

7 PART THREE Ensure all joints are clean and dry before applying sealant. 1. SEALANT APPLICATION STEPS For sealant application, follow steps (a) to (e) detailed below. For metallic finish shower, clear silicone and primer pen are supplied. Use primer pen to thoroughly prime all joints before application of sealant supplied. Allow 20 minutes for the primer to dry before application of the sealant. FAILURE TO PRIME BEFORE CLEAR SILICONE APPLICATION WILL VOID THE WARRANTY. White and Ivory showers have colour matched sealant supplied that do not require priming. (a) Cut tip of silicone tube nozzle at 45 O angle. SEALANT APPLICATION SILAFLEX NG SEALANT SHOULD BE AP- PLIED TO ALL OUTSIDE JOINTS. DO NOT SEAL FROM INSIDE. 2a. Seal full height the joint between the Walls and the Wall Retainers. b. Seal joint between the Door Sill, the Return Panel and the Shower Tray. d. Seal up to the PVC gasket joints between Return Panel & Corner Post and Return Panel & Wall Retainer. ALLOW 24 HOURS FOR SEALANT AND ADHESIVE TO CURE BEFORE USING THE SHOWER. e. On metallic finish shower, seal joint between 45 degree Corner Post and Magnetic Door Jamb. 6mm 45 (b) Hold the tube at 45 O angle and push forward as sealant fills the joint. (c) The surface of the sealant can be smoothed (before surface dries) by using a gloved finger dipped in a small quantity of water with one drop of washing liquid added. (d) Excess sealant should be removed immediately with a damp cloth. (e) Allow the silicone 24 hours to cure before using the enclosure. CAUTION: Avoid contact with skin, eyes and mouth and avoid breathing vapour. If in eyes, immediately flush with water. If irritation persists, seek medical attention. Keep out of reach of children. To a height of 100mm, seal c. joints between Door Frame & Corner Post. -7-

8 PART FOUR CLEANING AND MAINTENANCE INSTRUCTIONS Acrylic surfaces Glass Aluminium extrusions To clean acrylic surfaces use non abrasive soap and water. Wipe out the unit after each use to prevent a build-up of soap and scum. Glass is porous and this provides an ideal surface for shower grime to adhere, causing permanent staining. Use a squeegee or dry towel, to dry the glass after use. Regularly wash down extrusions with warm water and mild soap solution to prevent grime build up. Grime build up retains contaminated moisture permitting attack of the surface thereby damaging the finish. Where greasy deposits are concerned, cleaning may require a soft cloth dipped in white spirits. Thoroughly rinse with water after cleaning, especially where crevices are present to ensure removal of all residues. DO NOT USE: abrasive cleaners. acetone or alcohol. solvent based cleaners. harsh chemicals and desinfectants. products containing ammonia or peroxides. acid or alkaline cleaners. Always read the label instructions on any cleaner products before use. CALL US FOR HELP NEW ZEALAND KOHLER NZ Ltd. 133 Diana Drive, Glenfield, Auckland. Ph (09) Fax (09) info@kohler.co.nz AUSTRALIA KOHLER Co. Unit 10, St. Hilliers Road, Auburn, Sydney. NSW Ph (02) Fax (02) info@kohler.com.au All rights reserved to alter designs and specifications without notice. WARNING: Products in this leaflet are subject to Industrial Property Protection. All dimensions given are approximate only. Copyright Kohler NZ Ltd