MEDWAY SCHOOL RESOURCE PACK 2017

Transcription

1 MEDWAY SCHOOL RESOURCE PACK 2017 CREATED BY COMMISSIONED BY

2 STEP 3 STEP 4 STEP 1 STEP 2 Materials you will need: Cardboard (or a strong card, like mount board) Scissors, ruler, tape measure, tape & glue Black tissue paper, or similar (optional) Elastic Cut 2 x ovals from cardboard approx. 30cm x 23cm. One piece will be your hat s top, and the other the hat s rim. Cut-out an inner oval from one of the oval pieces. This inner oval should be the circumference of the wearer s head, and therefore sit neatly on their head. TIP: Cut the inner hole smaller than needed. You can always make the hole bigger, but you can t make it smaller! Check it fits and if not, cut the rim further to fit. NOTE: Template is provided in this pack to help you! Cut stripes of cardboard approx. 30cm x 3cm. Fold each end to create a fixing tab. Stick the tab to the hat s rim. We used a combination of gaffer tape and then fixed with a glue gun TIP: You could try stapling or just tape (you won t see the tape once you have covered the hat). Repeat process until you have cardboard strips around the entire rim. Fold the ends of each of the cardboard strips to create more fixing tabs. NOTE: it may be worth measuring where you fold to ensure your hat is even in height. We measured our strips at 23cm. Stick these tabs to the 2 nd oval piece. Again we used a combination of tape & glue gun. TIP: It is easier to place the hat s top on the table and stick the tabs down onto the oval, rather than trying to balance the oval on top of the tab ends! You should now have frame for your top hat. Check it fits. Add elastic straps if you would want extra support to hold on the wearer s head! Glue the frame and wrap black tissue paper over the frame. Depending on budgets and desired look you could also use fabric, paper or thin card to cover the structure. Gentlemen in top hats, 1850s

3 STEP 2 STEP 1 Making the bonnet structure Materials you will need: Cardboard (or a strong card, like mount board) Corrugated card or thin card Scissors, ruler, tape measure, tape & glue Tissue paper and elastic bands (or pipe cleaners/wire) Elastic Making the flowers Cut 1 x large oval cardboard approx. 45cm x 35cm from cardboard Cut 1 x top hat rim from cardboard (use template in this pack) Measure wearer s head and cut a hole in large oval piece for it to fit neatly on the head. TIP: Cut the inner hole smaller than needed. You can always make the hole bigger, but you can t make it smaller! Using the large oval as a template, draw & cut the same head-hole on the smaller oval. Cut strips of corrugated card or a thinner card measuring the length of the diameter of the wearer s head, plus a little extra for fixing. Place these strips over the large oval s hole, allow them to curve to the shape/depth of the wearer s head, and tape into place. Using the smaller oval, glue over the top to trap and secure the strips in place. Add elastic for extra support A.) Cut 5-8 sheets of tissue paper, approx. 12cm x 20cm. Layer together in a neat stack. B.) Fold the stack of papers together into a concertina (like a paper fan) C.) Tie the fan together with an elastic band at the centre point. NOTE: You could also use pipe-cleaners or wire, particularly if you want a stem to tie the flowers on with. D.) Trim both ends of the fan, with a curve. TIP: Experiment with curves, points and fringing cuts to create different looking flowers. E.) Open-up the fanned ends. It should look like this image at this stage. F.) Carefully peal-up each layer of tissue paper, on both sides. G.) Stick the flowers on the bonnet, using glue or tape. Repeat the process A-F to create a batch of flowers. Victorian lady in bonnet

4 Make a monocle 1.) Using the same method as make a tash, cut-out a monocle frame from thick card. 2.) Stick the monocle to the top of the stick. Materials you will need: Card sticks Scissors, Sticky tape or glue gun (Optional) felt (Optional) elastic Make a tash 1.) Choose your tash and photocopy this page. TIP: You can photocopy these template tashes, and alter the size to suit. 2.) Cut-out the tash and use it as a template to make your final paper/card tash. 3.) (Optional) Cover your paper tash with felt for a hairy effect! 4.) Fasten your tash to either a stick (see illustration) or with elastic to wear.

5 STEP 3 STEP 2 STEP 1 Cut a cardboard circle using the template provided. Puncture 6 holes evenly, about 1 cm from the edge. Spike the sticks through the holes, taping into place Gather the sticks at the other end and cable tie together (or tape). Cut off excess tie. You should have a tepee-shaped frame. Materials you will need: Cardboard 6 x sticks (approx. 65 cms) Cable tie Sticky tape Tissue paper & paper doilies Cut-out 2 cardboard handles using the template provided Hold them together and make a fold at the end of each handle so that they create feet/fixing tabs. Glue the handles together for a double layer and extra strength (avoiding gluing the feet/tabs). Then glue the tabs to the cardboard circle, as pictured. Cover the frame with glue Wrap the tepee frame in tissue paper (ideally white, as parasols were made with white/cream lace) Use more tissue paper or paper doilies to create a frill around the circle edges. Victorian lady with parasol

6 Get more creative experiences with Animate Arts Company Stand by your desks and greet a new Victorian teacher in your classroom! This brilliant costumed character teacher will visit classes in your school over the course of a day giving pupils an experience of how school life was in Victorian times. The visit will include a masterclass in classroom etiquette, a taster in lesson content and pupils will be able to ask the teacher questions about life in Victorian times. 250 for Victorian teacher for 1-day Now only available after 15 June 2017 Discover the Victorian past-time of shadow art with artist Wendy Daws. Victorians would use light to cast portraits on screens and then capture the silhouettes into art works. This workshop explores history through modern techniques. 225 for 2 class workshops in 1-day Extend your costume making into giant caged-skirts for the ladies and giant pocket watches for the gents. Work with a costume making to create amazing wearable artworks for the Dickens parade and school productions! 225 for 1-2 class workshops in 1 day + materials For further info and booking: holly@animatecommunityarts.com

7 TOP HAT TEMPLATE We recommend that this template is printed at A3 size for better proportions, however you can adjust the scale according to your wearer s head sizes!

8 PARASOL HANDLE You will need to make 2 x handles and glue them together (from curved handle to fold line).

9 PARASOL LID TEMPLATE