--- An integrated 3D EM design flow for EM/Circuit Co-Design
|
|
- Lucas Davidson
- 5 years ago
- Views:
Transcription
1 ADS users group meeting 2009 Rome 13/05, Böblingen 14-15/05, Massy 16/ An integrated 3D EM design flow for EM/Circuit Co-Design
2 Motivations and drivers for co-design Throw-The-Die-Over-The-Wall, the old way breaks down due to much smaller form factors of packages, chips, and so on Multichip modules, and stacked die become more common are now forcing IC and package designers to work together more closely Devices much closer in proximity induce parasitic couplings between them Increased use of multilayer embedded structures Requires more thorough circuit and EM (electromagnetic)-simulation and analysis among the IC, package, and pc board Chips Packages RF SiP SiP SMD PoP Board
3 Co-design case study Top layout view Die paddle Silicon Sub RF Board Input LTCC Balun DFN Package Output LTCC Balun
4 Sequential design process (1) Design of Differential RFIC PA RFIC PA Ideal Balun for Simulation Test
5 Sequential design process (2) Design of LTCC Balun S11 S21 & S31 Design Frequency: 2.45GHz
6 Sequential design process (3) Design of DFN package EM simulation Board 3D Bond Wire Connections Board Connections PCB via from Package to GND
7 Is the design completed? Every aspect of designs is done! IC design Balun design Package design Will the final (put all together) work as expected?
8 Integration (2) Simulation of Balun + RFIC PA + Package + Board Package S-Parameter Input Balun S-Parameter RFIC PA Sub-Circuit Output Balun S-Parameter
9 Design integration observations Pin Connectivity not obvious Pin Connectivity of different components is time consuming. It took 10 min to an ADS experienced user to create the final design. Pin Connectivity is error prone Now (only now!) we are going to discover the result of the integration of our different blocs.
10 Unexpected Parasitic Resonance! Parasitic resonances due to the interaction RFIC and package!
11 Customer experience with the non-integrated approach Non-Integrated EM Flow Minutes in the chart above represent additional design overhead
12 Chip-Package-Board (System) Co-Design Methodology Concurrently design chips, packages, and boards together to produce the cost effective, optimized electronic system that meets the performance goals both in frontend and backend design process Replace Throw-The-Die-Over-The-Wall old way ADS offers the best design platform for high speed and high frequency co-design Chips Packages RF SiP SiP SMD PoP Board
13 Use Agilent 3D EM without leaving ADS! ADS Layout with standard 3D components EMDS in ADS ADS circuit simulation with 3D components 3DEM integration in ADS design flow reduces design time, and risk of errors. Eliminate: - Transfer of design from ADS to stand-alone EM tool through GDS or Gerber files. - New assignment of material properties for each GDS or Gerber import. - New assignment of ports for each GDS or Gerber import. - Import of S parameters in ADS with the use of Layout Components
14 Why do we need 3D Fullwave EM for LTCC or Laminate designs? 3D View of the LTCC balun over the PC Board extended on the Z-axis by the ADS layout 3D viewer. L/C balun passives Balun design includes integrated inductors and capacitances. Dielectric bricks are not laterally infinite 3D Fullwave EM addresses these issues! Board
15 Why do we need 3D Fullwave EM for Package designs? 3D View of DFN package over RF Board. Extended on Z-axis 8 pin connections Package pins below the structure soldered on the RF Board Bond Wire connections have an arbitrary 3D shape 3D Fullwave EM addresses these issues! Board Board Connections 3D Bond Wire Connections PCB via from Package to GND
16 EMPro Core Custom 3D Components design kit ADS Layout EMPro Core Flow: Custom 3D components generation in EMPro Connectors, Solderballs, Solder bumps, shield, packages.. Any arbitrary 3D components ADS Design kit generation in EMPro Use 3D component from ADS 3D component design kit EM/circuit co-simulation of 3D components with other circuit components either in ADS layout or schematic NEW!
17 3D parameterized components Library Direct insertion into layout: Connectors Packages Wire bonds Solder balls Solder bumps Spiral inductors S1 D1 D2 S2 L2 L1 Solder Ball Bottom Drawing Layer Number of Facets (or Angle) Number of Rows Number of Columns Thickness for solder mask H
18 3D EM Design Flow with 3D Components Design Kit in ADS Install 3D Component Design Kit Place 3D component from the palette Edit 3D Component Parameters Complete ADS Layout Done! 3D EM Simulation 3D EM (FEM) Simulation Setup Check 3D View All in ADS!
19 Product Vision Two operation modes of platform EMPro Standalone Integrated in ADS ADS schematic ADS layout EMPro (3D editor) FEM FDTD Momentum FEM FDTD Same product!
20 Summary of Integrated 3D EM Design Flow in ADS Integrated EM saves cycle time Non-Integrated EM Flow Integrated EM Flow
21 Summary of benefits Use of Layout components avoids connectivity errors. Each of the 3DEM based models can be parameterized. Thus allowing sweep, tuning, and optimization. No need to export your layout to an external tool for 3DEM simulations. Layout changes are automatically taken into account by the integrated 3DEM FEM solver. The 3D component library provides ready-to-use components like solder balls, connectors, SMA launches, Allows you to get the fastest return out of your 3DEM tool investments
22 Conclusion Concurrently design chips, packages, and boards together to produce the cost effective, optimized electronic system that meets the performance goals. The integrated 3D EM design flow saves cycle time and increases first pass design success. To learn more, visit :
MMIC/RFIC Packaging Challenges Webcast (July 28, AM PST 12PM EST)
MMIC/RFIC Packaging Challenges Webcast ( 9AM PST 12PM EST) Board Package Chip HEESOO LEE Agilent EEsof 3DEM Technical Lead 1 Agenda 1. MMIC/RFIC packaging challenges 2. Design techniques and solutions
More informationInnovations in EDA Webcast Series
Welcome Innovations in EDA Webcast Series August 2, 2012 Jack Sifri MMIC Design Flow Specialist IC, Laminate, Package Multi-Technology PA Module Design Methodology Realizing the Multi-Technology Vision
More informationWhen Should You Apply 3D Planar EM Simulation?
When Should You Apply 3D Planar EM Simulation? Agilent EEsof EDA IMS 2010 MicroApps Andy Howard Agilent Technologies 1 3D planar EM is now much more of a design tool Solves bigger problems and runs faster
More informationUsing Sonnet EM Analysis with Cadence Virtuoso in RFIC Design. Sonnet Application Note: SAN-201B July 2011
Using Sonnet EM Analysis with Cadence Virtuoso in RFIC Design Sonnet Application Note: SAN-201B July 2011 Description of Sonnet Suites Professional Sonnet Suites Professional is an industry leading full-wave
More informationDesign and Analysis of Novel Compact Inductor Resonator Filter
Design and Analysis of Novel Compact Inductor Resonator Filter Gye-An Lee 1, Mohamed Megahed 2, and Franco De Flaviis 1. 1 Department of Electrical and Computer Engineering University of California, Irvine
More informationHow to anticipate Signal Integrity Issues: Improve my Channel Simulation by using Electromagnetic based model
How to anticipate Signal Integrity Issues: Improve my Channel Simulation by using Electromagnetic based model HSD Strategic Intent Provide the industry s premier HSD EDA software. Integration of premier
More informationEMDS for ADS Momentum
EMDS for ADS Momentum ADS User Group Meeting 2009, Böblingen, Germany Prof. Dr.-Ing. Frank Gustrau Gustrau, Dortmund User Group Meeting 2009-1 Univ. of Applied Sciences and Arts (FH Dortmund) Presentation
More informationOptimal design methodology for RF SiP - from project inception to volume manufacturing
Optimal design methodology for RF SiP - from project inception to volume manufacturing Chris Barratt Insight SiP 905 rue Albert Einstein Valbonne France 06560 Outline RF SiP Technologies Design Methodology
More informationAgilent EEsof EDA. Enabling First Pass Success. Chee Keong, Teo Business Development Manager EEsof South Asia. Agilent Restricted
Agilent EEsof EDA Enabling First Pass Success Chee Keong, Teo Business Development Manager EEsof South Asia EEsof EDA is Strategic to Agilent Technologies As the world s premier measurement company, Agilent
More information!"#$"%&' ()#*+,-+.&/0(
!"#$"%&' ()#*+,-+.&/0( Multi Chip Modules (MCM) or Multi chip packaging Industry s first MCM from IBM. Generally MCMs are horizontal or two-dimensional modules. Defined as a single unit containing two
More informationThe wireless industry
From May 2007 High Frequency Electronics Copyright Summit Technical Media, LLC RF SiP Design Verification Flow with Quadruple LO Down Converter SiP By HeeSoo Lee and Dean Nicholson Agilent Technologies
More informationSession 4: Mixed Signal RF
Sophia Antipolis October 5 th & 6 th 2005 Session 4: Mixed Signal RF Technology, Design and Manufacture of RF SiP Chris Barratt, Michel Beghin, Insight SiP Insight SiP Summary Introduction Definition of
More informationSynthesis of Optimal On-Chip Baluns
Synthesis of Optimal On-Chip Baluns Sharad Kapur, David E. Long and Robert C. Frye Integrand Software, Inc. Berkeley Heights, New Jersey Yu-Chia Chen, Ming-Hsiang Cho, Huai-Wen Chang, Jun-Hong Ou and Bigchoug
More informationA passive circuit based RF optimization methodology for wireless sensor network nodes. Article (peer-reviewed)
Title Author(s) Editor(s) A passive circuit based RF optimization methodology for wireless sensor network nodes Zheng, Liqiang; Mathewson, Alan; O'Flynn, Brendan; Hayes, Michael; Ó Mathúna, S. Cian Wu,
More informationSignal Integrity Modeling and Simulation for IC/Package Co-Design
Signal Integrity Modeling and Simulation for IC/Package Co-Design Ching-Chao Huang Optimal Corp. October 24, 2004 Why IC and package co-design? The same IC in different packages may not work Package is
More informationMultilayer VIA simulations using ADS Anurag Bhargava, Application Consultant, Agilent EEsof EDA, Agilent Technologies
Multilayer VIA simulations using ADS Anurag Bhargava, Application Consultant, Agilent EEsof EDA, Agilent Technologies Many a time designers find themselves in pretty confusing start when it comes to simulating
More informationINSIGHT SiP. RF System in Package, design methodology and practical examples of highly integrated systems
INSIGHT SiP RF System in Package, design methodology and practical examples of highly integrated systems Chris Barratt Insight SiP Sophia Antipolis France 1 RF SiP Technologies PRD Design Methodology Initial
More informationEM Insights Series. Episode #1: QFN Package. Agilent EEsof EDA September 2008
EM Insights Series Episode #1: QFN Package Agilent EEsof EDA September 2008 Application Overview Typical situation IC design is not finished until it is packaged. It is now very important for IC designers
More informationEvaluation of Package Properties for RF BJTs
Application Note Evaluation of Package Properties for RF BJTs Overview EDA simulation software streamlines the development of digital and analog circuits from definition of concept and estimation of required
More informationOptimization of Wafer Level Test Hardware using Signal Integrity Simulation
June 7-10, 2009 San Diego, CA Optimization of Wafer Level Test Hardware using Signal Integrity Simulation Jason Mroczkowski Ryan Satrom Agenda Industry Drivers Wafer Scale Test Interface Simulation Simulation
More informationInductor Modeling of Integrated Passive Device for RF Applications
Inductor Modeling of Integrated Passive Device for RF Applications Yuan-Chia Hsu Meng-Lieh Sheu Chip Implementation Center Department of Electrical Engineering 1F, No.1, Prosperity Road I, National Chi
More informationAgilent EEsof EDA.
Agilent EEsof EDA This document is owned by Agilent Technologies, but is no longer kept current and may contain obsolete or inaccurate references. We regret any inconvenience this may cause. For the latest
More information2. Design Recommendations when Using EZRadioPRO RF ICs
EZRADIOPRO LAYOUT DESIGN GUIDE 1. Introduction The purpose of this application note is to help users design EZRadioPRO PCBs using design practices that allow for good RF performance. This application note
More informationFront-To-Back MMIC Design Flow with ADS. Speed MMICs to market Save money and achieve high yield
Front-To-Back MMIC Design Flow with ADS Speed MMICs to market Save money and achieve high yield 1 Unique Tools for Robust Designs, First Pass, and High Yield Yield Sensitivity Histogram (YSH) to components
More informationUsing Analyst TM to Quickly and Accurately Optimize a Chip-Module-Board Transition
Using Analyst TM to Quickly and Accurately Optimize a Chip-Module-Board Transition 36 High Frequency Electronics By Dr. John Dunn 3D electromagnetic Optimizing the transition (EM) simulators are commonly
More informationApplication Note 5525
Using the Wafer Scale Packaged Detector in 2 to 6 GHz Applications Application Note 5525 Introduction The is a broadband directional coupler with integrated temperature compensated detector designed for
More informationCMT2300AW Schematic and PCB Layout Design Guideline
AN141 CMT2300AW Schematic and PCB Layout Design Guideline Introduction This document is the CMT2300AW Application Development Guideline. It will explain how to design and use the CMT2300AW schematic and
More informationApplication Note 1330
HMPP-3865 MiniPAK PIN Diode High Isolation SPDT Switch Design for 1.9 GHz and 2.45 GHz Applications Application Note 133 Introduction The Avago Technologies HMPP-3865 parallel diode pair combines low inductance,
More informationMSPP Page 1. MSPP Competencies in SiP Integration for Wireless Applications
MSPP Page 1 MSPP Competencies in SiP Integration for Wireless Applications MSPP Page 2 Outline Design, simulation and measurements tools MSPP competencies in electrical design and modeling Embedded passive
More informationJohanson Technology, Inc. 2450BM14A0002 Matched Balun for the Nordic nrf24l01/nrf24l01+ Chipsets. November 2009
Johanson Technology, Inc. 2450BM14A0002 Matched Balun for the Nordic nrf24l01/nrf24l01+ Chipsets November 2009 1. Introduction The nrf24l01/nrf24l01+ from Nordic Semiconductor is a 2.45GHz one chip, ultra
More informationConsiderations in High-Speed High Performance Die-Package-Board Co-Design. Jenny Jiang Altera Packaging Department October 2014
Considerations in High-Speed High Performance Die-Package-Board Co-Design Jenny Jiang Altera Packaging Department October 2014 Why Co-Design? Complex Multi-Layer BGA Package Horizontal and vertical design
More informationMGA MMIC RF amplifier applications PAG. 1
MGA-85563 MMIC RF amplifier applications PAG. 1 MGA-85563 is an Agilent (formerly HP now Avago) MMIC for applications as amplifier up to 6 GHz, it is specified from 800 MHz buti t can be used also from
More informationAWR. SIP Flow White Paper UNDERSTANDING AVAILABLE TOOLS FOR RF SYSTEM-IN-PACKAGE AND MULTI-CHIP-MODULE DESIGN AND OPTIMIZATION
UNDERSTANDING AVAILABLE TOOLS FOR RF SYSTEM-IN-PACKAGE AND MULTI-CHIP-MODULE DESIGN AND OPTIMIZATION RF system-in-package (SiP) and multi-chip-module (MCM) designs present engineers with the challenge
More informationAnaren 0805 (B0809J50ATI) balun optimized for Texas Instruments CC1100/CC1101 Transceiver
(ANN-2005) Rev B Page 1 of 13 Anaren 0805 (B0809J50ATI) balun optimized for Texas Instruments CC1100/CC1101 Transceiver Trong N Duong RF Co-Op Nithya R Subramanian RF Engineer Introduction The tradeoff
More informationDESIGN AND PERFORMANCE ANALYSIS OF RADIO FREQUENCY MEANDERED-LINE MICROSTRIPS
DESIGN AND PERFORMANCE ANALYSIS OF RADIO FREQUENCY MEANDERED-LINE MICROSTRIPS BY YIXUAN ZHAO THESIS Submitted in partial fulfillment of the requirements for the degree of Bachelor of Science in Electrical
More informationAntenna Matching Within an Enclosure Part II: Practical Techniques and Guidelines
Antenna Matching Within an Enclosure Part II: Practical Techniques and Guidelines By Johnny Lienau, RF Engineer June 2012 Antenna selection and placement can be a difficult task, and the challenges of
More informationEfficient Electromagnetic Analysis of Spiral Inductor Patterned Ground Shields
Efficient Electromagnetic Analysis of Spiral Inductor Patterned Ground Shields James C. Rautio, James D. Merrill, and Michael J. Kobasa Sonnet Software, North Syracuse, NY, 13212, USA Abstract Patterned
More informationFlip-Chip for MM-Wave and Broadband Packaging
1 Flip-Chip for MM-Wave and Broadband Packaging Wolfgang Heinrich Ferdinand-Braun-Institut für Höchstfrequenztechnik (FBH) Berlin / Germany with contributions by F. J. Schmückle Motivation Growing markets
More informationTop View (Near-side) Side View Bottom View (Far-side) .89±.08. 4x.280. Orientation Marker Orientation Marker.
Model B2F2AHF Ultra Low Profile 168 Balun Ω to 2Ω Balanced Description The B2F2AHF is a low profile sub-miniature balanced to unbalanced transformer designed for differential input locations on data conversion
More informationLecture 5: Dynamic Link
Lecture 5: Dynamic Link 2015.0 Release ANSYS HFSS for Antenna Design 1 2015 ANSYS, Inc. Antenna System Co-Simulation Transmit/Receive (T/R) Module Block Diagram Antenna Element Replicate Times Power
More informationAnalysis signal transitions characteristics of BGA-via multi-chip module Baolin Zhou1,a, Dejian Zhou1,b
5th International Conference on Computer Sciences and Automation Engineering (ICCSAE 2015) Analysis signal transitions characteristics of BGA-via multi-chip module Baolin Zhou1,a, Dejian Zhou1,b 1 Electromechanical
More informationMAX2045/MAX2046/MAX2047 Evaluation Kits
19-2793; Rev 0a; 4/03 MAX2045/MAX2046/MAX2047 Evaluation Kits General Description The MAX2045/MAX2046/MAX2047 evaluation kits (EV kits) simplify evaluation of the MAX2045/MAX2046/ MAX2047 vector multipliers.
More informationOptimization of Symmetric Spiral Inductors On Silicon Substrate
Optimization of Symmetric Spiral Inductors On Silicon Substrate Hyunjin Lee, Joonho Gil, and Hyungcheol Shin Department of Electrical Engineering and Computer Science, KAIST -1, Guseong-dong, Yuseong-gu,
More informationTutorial: Getting Started with RFIC Inductor Toolkit
Tutorial: Getting Started with RFIC Inductor Toolkit Table of contents: Tutorial: Getting Started with RFIC Inductor Toolkit... 1 Introduction... 2 Installation... 2 Create a new example workspace... 3
More informationPackaging Roadmap: The impact of miniaturization. Bob Pfahl, inemi Celestica-iNEMI Technology Forum May 15, 2007
Packaging Roadmap: The impact of miniaturization Bob Pfahl, inemi Celestica-iNEMI Technology Forum May 15, 2007 The Challenges for the Next Decade Addressing the consumer experience using the converged
More informationLow Noise Amplifier Design Methodology Summary By Ambarish Roy, Skyworks Solutions, Inc.
February 2014 Low Noise Amplifier Design Methodology Summary By Ambarish Roy, Skyworks Solutions, Inc. Low Noise Amplifiers (LNAs) amplify weak signals received by the antenna in communication systems.
More informationSignal Integrity Design of TSV-Based 3D IC
Signal Integrity Design of TSV-Based 3D IC October 24, 21 Joungho Kim at KAIST joungho@ee.kaist.ac.kr http://tera.kaist.ac.kr 1 Contents 1) Driving Forces of TSV based 3D IC 2) Signal Integrity Issues
More informationDESIGN OF HIGH POWER AND EFFICIENT RF LDMOS PA FOR ISM APPLICATIONS
DESIGN OF HIGH POWER AND EFFICIENT RF LDMOS PA FOR ISM APPLICATIONS Farhat Abbas and John Gajadharsing NXP Semiconductors Nijmegen, The Netherlands Farhat.abbas@nxp.com Very high performance in power and
More informationUsing Accurate Component Models to Achieve First-Pass Success in Filter Design
Application Example Using Accurate Component Models to Achieve First-Pass Success in Filter Design Overview Utilizing models that include component and printed circuit board (PCB) parasitics in place of
More informationElectrical Test Vehicle for High Density Fan-Out WLP for Mobile Application. Institute of Microelectronics 22 April 2014
Electrical Test Vehicle for High Density Fan-Out WLP for Mobile Application Institute of Microelectronics 22 April 2014 Challenges for HD Fan-Out Electrical Design 15-20 mm 7 mm 6 mm SI/PI with multilayer
More informationFraunhofer IZM - ASSID
FRAUNHOFER-INSTITUT FÜR Zuverlässigkeit und Mikrointegration IZM Fraunhofer IZM - ASSID All Silicon System Integration Dresden Heterogeneous 3D Wafer Level System Integration 3D system integration is one
More informationInnovative Electrical Thermal Co-design of Ultra-high Q TPV-based 3D Inductors. Glass Packages
2016 IEEE 66th Electronic Components and Technology Conference Innovative Electrical Thermal Co-design of Ultra-high Q TPV-based 3D Inductors in Glass Packages Min Suk Kim, Markondeya Raj Pulugurtha, Zihan
More informationECE 145A/218A, Lab Project #1a: passive Component Test.
ECE 145A/218A, Lab Project #1a: passive Component Test. September 28, 2017 OVERVIEW... 2 GOALS:... 2 PRECAUTIONS TO AVOID INSTRUMENT DAMAGE... 2 SAFETY PRECAUTIONS... 2 READING:... 3 NETWORK ANALYZER CALIBRATION...
More informationUnderstanding, measuring, and reducing output noise in DC/DC switching regulators
Understanding, measuring, and reducing output noise in DC/DC switching regulators Practical tips for output noise reduction Katelyn Wiggenhorn, Applications Engineer, Buck Switching Regulators Robert Blattner,
More informationStreamlined Design of SiGe Based Power Amplifiers
ROMANIAN JOURNAL OF INFORMATION SCIENCE AND TECHNOLOGY Volume 13, Number 1, 2010, 22 32 Streamlined Design of SiGe Based Power Amplifiers Mladen BOŽANIĆ1, Saurabh SINHA 1, Alexandru MÜLLER2 1 Department
More information3D IC-Package-Board Co-analysis using 3D EM Simulation for Mobile Applications
3D IC-Package-Board Co-analysis using 3D EM Simulation for Mobile Applications Darryl Kostka, CST of America Taigon Song and Sung Kyu Lim, Georgia Institute of Technology Outline Introduction TSV Array
More informationDemystifying Vias in High-Speed PCB Design
Demystifying Vias in High-Speed PCB Design Keysight HSD Seminar Mastering SI & PI Design db(s21) E H What is Via? Vertical Interconnect Access (VIA) An electrical connection between layers to pass a signal
More informationCommon myths, fallacies and misconceptions in Electromagnetic Compatibility and their correction.
Common myths, fallacies and misconceptions in Electromagnetic Compatibility and their correction. D. A. Weston EMC Consulting Inc 22-3-2010 These are some of the commonly held beliefs about EMC which are
More informationAN4819 Application note
Application note PCB design guidelines for the BlueNRG-1 device Introduction The BlueNRG1 is a very low power Bluetooth low energy (BLE) single-mode system-on-chip compliant with Bluetooth specification
More informationRF Board Design for Next Generation Wireless Systems
RF Board Design for Next Generation Wireless Systems Page 1 Introduction Purpose: Provide basic background on emerging WiMax standard Introduce a new tool for Genesys that will aide in the design and verification
More informationROBUSPIC Workshop. ESSDERC 06 Montreux, Switzerland Friday 22 nd of September. ESSDERC 06, Montreux ROBUSPIC Workshop A.
ROBUSPIC Workshop ESSDERC 06 Montreux, Switzerland Friday 22 nd of September ESSDERC 06, Montreux ROBUSPIC Workshop A. Baric Slide 1 Vladimir Ceperic, Adrijan Baric - University of Zagreb, Croatia Renaud
More information1-24 GHz Distributed Driver Amplifier
Features Functional Block Diagram Wide bandwidth High linearity Single positive supply voltage On chip bias choke Description The CMD197C4 is a wideband GaAs MMIC driver amplifier housed in a leadless
More informationLTCC-Breitband-Balun. für einen Gegentaktverstärker
LTCC @ IMST LTCC-Breitband-Balun für einen Gegentaktverstärker Dr. Jürgen Kassner, RF-Modules Reinhard Kulke, RF-Modules Dr. Andreas Lauer, Field Simulation and Modelling Dr. Dietmar Köther, Measurement
More informationMaxim Integrated Products 1
19-3533; Rev 0; 1/05 MAX9996 Evaluation Kit General Description The MAX9996 evaluation kit (EV kit) simplifies the evaluation of the MAX9996 UMTS, DCS, and PCS base-station downconversion mixer. It is
More informationEDA Toolsets for RF Design & Modeling
Yiannis Moisiadis, Errikos Lourandakis, Sotiris Bantas Helic, Inc. 101 Montgomery str., suite 1950 San Fransisco, CA 94104, USA Email: {moisiad, lourandakis, s.bantas}@helic.com Abstract This paper presents
More informationMICROELECTRONICS ASSSEMBLY TECHNOLOGIES. The QFN Platform as a Chip Packaging Foundation
West Coast Luncheon January 15, 2014. PROMEX PROMEX INDUSTRIES INC. MICROELECTRONICS ASSSEMBLY TECHNOLOGIES The QFN Platform as a Chip Packaging Foundation 3075 Oakmead Village Drive Santa Clara CA Ɩ 95051
More informationSiP packaging technology of intelligent sensor module. Tony li
SiP packaging technology of intelligent sensor module Tony li 2016.9 Contents What we can do with sensors Sensor market trend Challenges of sensor packaging SiP technology to overcome challenges Overview
More informationETI , Good luck! Written Exam Integrated Radio Electronics. Lund University Dept. of Electroscience
und University Dept. of Electroscience EI170 Written Exam Integrated adio Electronics 2010-03-10, 08.00-13.00 he exam consists of 5 problems which can give a maximum of 6 points each. he total maximum
More informationControlled Impedance Line Designer
Heidi Barnes WW HSD Application Engineer Controlled Impedance Line Designer Stephen Slater HSD Product Manager EDA Simulation Tools for Power Integrity Agenda 1. Designing a channel for a desired impedance
More informationIndex. Cambridge University Press Silicon Photonics Design Lukas Chrostowski and Michael Hochberg. Index.
absorption, 69 active tuning, 234 alignment, 394 396 apodization, 164 applications, 7 automated optical probe station, 389 397 avalanche detector, 268 back reflection, 164 band structures, 30 bandwidth
More informationA Simulation Methodology for Wirebonds Interconnects of Radiofrequency Integrated Circuits
A Simulation Methodology for Wirebonds Interconnects of Radiofrequency Integrated Circuits Hercílio M. Cavalcanti 1 and Leandro T. Manera 2 1 Hercílio M. Cavalcanti, CTI Renato Archer, Campinas, São Paulo,
More informationTime Domain EM Modelling. W. Simon, , serv0
Time Domain EM Modelling Introduction 3D full wave electromagnetic field solver (FDTD) Accurate: Validated with theory & measurements Versatile: Covering all passive RF-structures Efficient: Low memory
More informationChapter 6. Case Study: 2.4-GHz Direct Conversion Receiver. 6.1 Receiver Front-End Design
Chapter 6 Case Study: 2.4-GHz Direct Conversion Receiver The chapter presents a 0.25-µm CMOS receiver front-end designed for 2.4-GHz direct conversion RF transceiver and demonstrates the necessity and
More informationMACP Temperature Compensated Directional RMS Power Detector GHz Rev. V1 Features Functional Schematic Description Pin Configuration 3
Features Integrated Directional Coupler Low Insertion Loss:.5 db @ Min. detectable power: -15 dbm @ Dynamic range: 45 db @ Built-In Temperature Compensation Lead-Free 1.5 x 1.2 mm 6-Lead TDFN Halogen-Free
More information544 IEEE TRANSACTIONS ON ADVANCED PACKAGING, VOL. 31, NO. 3, AUGUST /$ IEEE
544 IEEE TRANSACTIONS ON ADVANCED PACKAGING, VOL. 31, NO. 3, AUGUST 2008 Modeling and Measurement of Interlevel Electromagnetic Coupling and Fringing Effect in a Hierarchical Power Distribution Network
More informationRuth Kastner Eli Moshe. Embedded Passives, Go for it!
Ruth Kastner Eli Moshe Embedded Passives, Go for it! Outline Description of a case study: Problem definition New technology to the rescue: Embedded passive components Benefits from new technology Design
More informationWide-Band Two-Stage GaAs LNA for Radio Astronomy
Progress In Electromagnetics Research C, Vol. 56, 119 124, 215 Wide-Band Two-Stage GaAs LNA for Radio Astronomy Jim Kulyk 1,GeWu 2, Leonid Belostotski 2, *, and James W. Haslett 2 Abstract This paper presents
More information8x8 Red Blue Green Yellow Audio Indicator
8x8 Red Blue Green Yellow Audio Indicator 1. Introduce. 1>. Working voltage: 5V. 2>. PCB size: 75*45mm. 3>. There are four fixed mounting holes on PCB. 4>. It is no need for filter circuit. It can driver
More informationK-band Waveguide BPF Design using Agilent EMPro Anurag Bhargava Application Consultant Agilent EEsof EDA
K-band Waveguide BPF Design using Agilent EMPro 2013 Anurag Bhargava Application Consultant Agilent EEsof EDA Filter Specifications Center Frequency (Fc): 25 GHz 3dB Bandwidth: 150 MHz Rejection: 40 db
More informationEM Simulation of Automotive Radar Mounted in Vehicle Bumper
EM Simulation of Automotive Radar Mounted in Vehicle Bumper Abstract Trends in automotive safety are pushing radar systems to higher levels of accuracy and reliable target identification for blind spot
More informationIntegrated Passive Device (IPD) Technology for Wireless Applications
Ultra-Wide-Band (UWB) Band-Pass-Filter Using Integrated Passive Device (IPD) Technology for Wireless Applications June 17, 2009 STATS ChipPAC D&C YongTaek Lee Rev01 Agenda Introduction Design and characterization
More informationTop View (Near-side) Side View Bottom View (Far-side) ± ±.08. 4x.28. Orientation Marker Balanced port 1.
Model BD2FAHF Ultra Low Profile 168 Balun Ω to Ω Balanced Description The BD2FAHF is a low profile sub-miniature balanced to unbalanced transformer designed for differential input locations on data conversion
More informationAN-1370 APPLICATION NOTE
APPLICATION NOTE One Technology Way P.O. Box 9106 Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 Fax: 781.461.3113 www.analog.com Design Implementation of the ADF7242 Pmod Evaluation Board Using the
More informationChapter 2. Inductor Design for RFIC Applications
Chapter 2 Inductor Design for RFIC Applications 2.1 Introduction A current carrying conductor generates magnetic field and a changing current generates changing magnetic field. According to Faraday s laws
More informationIntroduction to EMI/EMC Challenges and Their Solution
Introduction to EMI/EMC Challenges and Their Solution Dr. Hany Fahmy HSD Application Expert Agilent Technologies Davy Pissort, K.U. Leuven Charles Jackson, Nvidia Charlie Shu, Nvidia Chen Wang, Nvidia
More informationPI3HDMIxxx 4-Layer PCB Layout Guideline for HDMI Products
PI3HDMIxxx 4-Layer PCB Layout Guideline for HDMI Products Introduction The differential trace impedance of HDMI is specified at 100Ω±15% in Test ID 8-8 in HDMI Compliance Test Specification Rev.1.2a and
More informationCharacterization of on-chip balun with patterned floating shield in 65 nm CMOS
Vol. 32, No. Journal of Semiconductors October 2011 Characterization of on-chip balun with patterned floating shield in 5 nm CMOS Wei Jiaju( 韦家驹 ) and Wang Zhigong( 王志功 ) Institute of RF- & OE-ICs, Southeast
More informationDesign Considerations for Highly Integrated 3D SiP for Mobile Applications
Design Considerations for Highly Integrated 3D SiP for Mobile Applications FDIP, CA October 26, 2008 Joungho Kim at KAIST joungho@ee.kaist.ac.kr http://tera.kaist.ac.kr Contents I. Market and future direction
More informationUltra-Wide-Band (UWB) Band-Pass-Filter Using Integrated Passive Device (IPD) Technology for Wireless Applications. STATS ChipPAC D&C YongTaek Lee
Ultra-Wide-Band (UWB) Band-Pass-Filter Using Integrated Passive Device (IPD) Technology for Wireless Applications June 17, 2009 STATS ChipPAC D&C YongTaek Lee Rev01 Agenda Introduction Design and characterization
More informationCMD175P GHz 5-Bit Digital Phase Shifter. Features. Functional Block Diagram. Description
Features Functional Block Diagram Low phase error Low insertion loss 36 phase shift, LSB = 11.25 Single bit negative logic Pb-free RoHs compliant 4x4 QFN package Description The CMD175P4 is a GaAs MMIC
More informationEvaluate: MAX2828/MAX2829. MAX2828/MAX2829 Evaluation Kits. General Description. Features. Quick Start. Connections and Setup. Test Equipment Required
MAX2828/MAX2829 Evaluation Kits Evaluate: MAX2828/MAX2829 General Description The MAX2828/MAX2829 evaluation kits (EV kits) simplify the testing of the MAX2828/MAX2829. The EV kits provide 50Ω SMA connectors
More informationRFPA5542 WLAN POWER AMPLIFIER 5 GHz WLAN PA (11a/n/ac)
RFPA5542 WLAN POWER AMPLIFIER 5 GHz WLAN PA (11a/n/ac) Introduction This application note explains the operation of the RFPA5542 5GHz WLAN PA. The RFPA5542 is a three-stage power amplifier (PA) designed
More informationModeling Physical PCB Effects 5&
Abstract Getting logical designs to meet specifications is the first step in creating a manufacturable design. Getting the physical design to work is the next step. The physical effects of PCB materials,
More informationCHAPTER 4. Practical Design
CHAPTER 4 Practical Design The results in Chapter 3 indicate that the 2-D CCS TL can be used to synthesize a wider range of characteristic impedance, flatten propagation characteristics, and place passive
More informationReturn loss (db) Insertion loss (db) .56±.06 TBD. GND / DC Feed 1 + RF GND 2. Unbalanced Port Balanced Port Balanced Port.
Model BD6N5AHF Ultra Low Profile 44 Balun 5Ω to Ω Balanced Description The BD6N5AHF is a low cost, low profile sub-miniature unbalanced to balanced transformer designed for differential inputs and output
More information300 frequencies is calculated from electromagnetic analysis at only four frequencies. This entire analysis takes only four minutes.
Electromagnetic Analysis Speeds RFID Design By Dr. James C. Rautio Sonnet Software, Inc. Liverpool, NY 13088 (315) 453-3096 info@sonnetusa.com http://www.sonnetusa.com Published in Microwaves & RF, February
More informationHenry Lau Lexiwave Technology, Inc
RF PCB Design Henry Lau Lexiwave Technology, Inc December 4, 2012 1 AWR Corporation Overview & Introduction AWR - At a Glance The Innovation Leader in High-Frequency EDA Product Portfolio: Microwave Office
More informationModel BD1631J50100AHF
Model BD1631J51AHF Ultra Low Profile 85 Balun 5Ω to 1Ω Balanced Description The BD1631J51AHF is a low profile sub-miniature balanced to unbalanced transformer designed for differential inputs and output
More informationEquivalent Circuit Model Overview of Chip Spiral Inductors
Equivalent Circuit Model Overview of Chip Spiral Inductors The applications of the chip Spiral Inductors have been widely used in telecommunication products as wireless LAN cards, Mobile Phone and so on.
More informationPackaged mm-wave GaN, GaAs and Si ICs for 5G and automotive radar
Packaged mm-wave GaN, GaAs and Si ICs for 5G and automotive radar Eric Leclerc UMS 1 st Nov 2018 Outline Why heterogenous integration? About UMS Technology portfolio Design tooling: Cadence / GoldenGate
More information