P-39 Airacobra INSTRUCTION MANUAL SAFETY PRECAUTIONS. Specification: 30cc gasoline engine. This R/C airplane is not a toy!
|
|
- Prosper Gaines
- 5 years ago
- Views:
Transcription
1 P-39 Airacobra Specification: Length: Wing span: Wing area: Wing loading: Flying weight: Radio: Engine: 7mm(70. ) 00mm(0.3 ) 7.5sq.dm(.5sq.ft) 93g/sq.dm(30.5oz/sq.ft) 7.3kg(.bs) ch & servos 30cc gasoline engine INSTRUCTION MANUAL SAFETY PRECAUTIONS This R/C airplane is not a toy! (The people under years old is forbidden from flying this model) First-time builders should seek advice from people having building experience.if misused or abused,it can cause serious bodily injury and damage to property. Fly only in open areas and preferably at a dedicated R/C flying site. We suggest having a qualified instructor carefully inspect your airplane before its first flight.please carefully read and follow all instructions included with this airplane,your radio control system and any other components purchased separately.
2 channel radio for aiplane is highly recommended for this model. -cycle.0 9 Optional parts: rubber wheel with metal hub. Spinner X0 We strongly recommen you use the thread lock for all the screws when you build your model.
3 Three wheel retract system Make sure to assemble retracts as instructed below. Rod (x300mm) TP Screw (.3xmm) Screw (3x0mm) Servo tray(.5x5.5xmm) Wooden Block(0x0xmm) Pin hinge(xmm) Washer(3x5mm) Washer(3x5mm) 3 Assemble the aileron to main wing with instant type AB glue. Be careful to ensure the moving parts of the hinges are able to move freely. Securely glue together. If coming off during flights, you 'll lose control of your airplane which leads to accidents! Strut 3-way pressure inlet 3-way pressure inlet Apply instant AB glue to aileron and pin hinge. Pin hinge(xmm) Install the servo as the illustration below Strut 3-way pressure inlet 3-way pressure inlet Strut Air inlet 3-way pressure inlet Air tank Make sure hinges are mounted in the same line. Quick release connector Pressure reduction inlet Quick release connector Ø0.mm Keep some space about mm width between aileron and trailing edge. 5 Install the nylon control horn and connect the linkage. Ø.7mm Switch Trailing edge Rod (x300mm) Aileron Air valve The status when the gear up Please insure the sealing of the retract system before flight. Pleas notice the inner diameter for each side of the pressure reduction inlet. Air valve Pull out length of mm to make gear down TP Screw(.xmm) Rod (X300mm) Strut ( 90 ) Switch Air line (3000mm) 3-way pressure inlet Air tank Air inlet Quick release connector Strut ( 90 ) 5 Make sure they are in the right position while installing. mm Screw (x0mm)
4 Secure and connect the servo.install the linkage. the nylon control horn Keep some space about mm width between trailing edge and flap. 7 The centre of the Gravity. TP Screw (.3xmm) TP Screw (.3xmm) Trailing edge Rod (x300mm).5mm Flap Screw (x0mm) Washer(3x5mm) Washer Screw (3x0mm) 3mm Make sure they are in the right position while installing. mm 50mm 9 Epoxy the flaps to the wings as illustration. Rod (x300mm) TP Screw (.3xmm) Screw (3x) Servo tray(.5x5.5xmm) Wooden Block(0x0xmm) Pin hinge(xmm) Washer(3x5mm) Washer(3x5mm) Securely glue together. If coming off during flights, you 'll lose control of your airplane which leads to accidents! 7 Epoxy the pin hinges to the flap. 0 Install the servo as the illustration below Pin hinge(xmm) 5
5 70 Epoxy the landing gear to the wing steadily. 73 Adjustment. Install the nylon control horn and connect the linkage. 3 Mount the gear door and the wheel to the retract. Rod (x300mm) Bushing (Xmm) Wheel (00mm) Side View inside LockNut(mm) RUDDER 0mm Screw (x0mm) 0mm Note:rubber wheels oleo struts and retracts are optional. Top view 7 Install the wheel to the fixed landing gear. 7 Adjustment. Secure the servo.install the nylon control horn and connect the linkage. Cut away the surplus parts of plastic cover carefully along the shaded line. TP Screw (.3xmm) ELEVATOR Top view.5mm TP Screw (.3xmm) Rod (x300mm) 5mm 3mm Screw (x0mm) Washer(3x5mm) Side View Washer Collar 5mm 3 Centre of Gravity. Position for right diagram. Screw (3x) 7 Epoxy the fixed landing gear to the relevant position in the fuselage. 75 Adjustment. 5 Trim the covering for assembling the wheel well carefully. Side View AILERON FLAP AILERON FLAP 0mm Wheel (00mm) Bushing (xmm) LockNut (mm) TP Screw (3x0mm) Washer (3xmm) Wood dowel (x) Wood dowel (x50mm) PVC part Main wing joiner Rib template (mm ply) Screw(x50mm) Blind Nut (mm) Reinforcement Plate 3
6 Epoxy the wheel house to the wings carefully. 9 According to the rib template drill holes in one wing and epoxy wood dowel in them. Rib template (mm ply) Wood dowel (x) Main wing joiner 5 Epoxy plies to relevant position inside the fuselage as below for assembling the cowling. TP Screw (.3xmm).5mm Epoxy the exhaust to appropriate position in the fuselage as illustration. mm Rib template (mm ply) Main wing joiner Note:Please fix the air tube before assemble the wheel house to the wing. Wood dowel (x) TP Screw (.3xmm) Ply (5x5x3mm) Pvc part 7 Assemble the landing gear to the wheel house. 0 According to the rib template drill holes to another main wing. Cut the surplus shaded portion carefully off the canopy and exhaust..mm Washer (3xmm) TP Screw (3x0mm) TP Screw (3x0mm) Washer (3xmm) Rib template (mm ply) mm Wheel (00mm) Wooden supporter (.5xxmm) Landing gear(5mm) TP Screw (3x0mm ) Landing gear straps Wooden Block(x0xmm) Wooden Block(x5xmm) 7 Wheel (90mm) Wooden supporter (xxmm) Landing gear(5mm) TP Screw (.3xmm) Aluminum part(0xmm) Gear door The sketch map when the main wing assembled completely. Trim holes in the appropriate position in the wings and drag the servo wire and the air tube out. 7 Epoxy plies inside the fuselage under the cowing and mount the canopy with TP screw as illustration. 9 Assemble the wheel and gear door to landing gear. Make sure to glue securely. If not properly glued, a failure in flight may occur. Securely glue together.if coming off during flights, you'll lose control of your airplane which leads to accidents! For air tube 0mm R0mm TP Screw (.3xmm) TP Screw (3x0mm) TP Screw (3x0mm) Washer (3xmm) A A` For servo wire 00mm R0mm Wooden Block A=A' TP Screw (.3xmm).5mm Ply (5x5x3mm) Wooden supporter 3
7 0 Install the servo. The servos installation finished sketch map. Epoxy the main wing hardly together with wing joiner. 3 5 Assemble the wings to the fuselage with screw and blind nut as below. Screw (x0mm) Ball joint Washer(x5mm) Lock Nut (mm ) Throttle servo Elevator servo.mm Steel wire Nose wheel servo Blind Nut Screw(x50mm) Screw (x0mm) Nut (mm ) Washer(x5mm) switch servo Rudder servo Securely glue together. If coming off during flights, you 'll lose control of your airplane which leads to accidents! Screw(x50mm) Blind Nut (mm) Reinforcement Plate Reinforcement Plate Mount the servo of nose wheel to the fuselage. 3 Drill holes to appropriate position in the front of mid wing and epoxy wood dowel in them. Canopy TP Screw (.3xmm) Ply(5x5x3mm) Pvc part 0mm Wood dowel (x50mm) mm Wood dowel (x50mm) Blind Nut (mm) Screw (x35mm) Screw (x5mm) Washer(xmm) Spring Washer (mm) Nut (mm) Linkage Stopper Plastic tube (x50mm) Engine mount (x05mm) Fuel tank (550cc) Install the servo of switch. Trim the cowling for engine and muffler. Drill holes to relevant position in the fuselage. The front view of the engine installation finished. mm mm 0mm In case of -cycle & -cycle engine. 5
8 7 The side sketch map of the engine installation finished. mm 30 Assemble the accelerator push rod to the engine. Set Screw (3xmm) Linkage Stopper Washer (mm) Washer (xmm) Rod (x50mm) 55 Install the rudder servo to appropriate position in the fuselage. 5 Assemble the wheel and oleo strut to the retract as illustration. Screw (x5mm) Washer(xmm) Brass collar (5mm) Wheel (75 mm) Aluminum shaft Brass collar (5mm) Screw (x5mm) Set Screw (mm) Set Screw (mm) Set Screw (3xmm) Note:rubber wheels oleo struts and retracts are optional. Steering fullarm (0xmm) Washer(xmm) Screw (x5mm) Washer(xmm) Aluminum shaft(5x50mm) Steering fullarm (0xmm) Wheel (75 mm) Drill holes and set blind nut in appropriate position in the firewall before install the engine. 3 Engine installation finished sketch map. 5 The sketch map of the linkages for the rudder and elevator in the fuselage. 59 Assemble the retract to the fuselage with TP Screw as illustration. TP Screw(3x0mm) Elevator servo 5.mm Blind Nut Rudder servo.mm Blind Nut (mm) TP Screw(3x0mm) 9 Install the engine carefully. Screw (x35mm) 3 Assembly of the fuel tank. 0 Assemble the steel wire to the nose arm. Washer (xmm) Washer (xmm) Spring Washer (mm) Nut (mm) mm Washer (xmm) Screw (x5mm) Air pressure line Fuel spray line Fuel supply line wheel (90mm) Bushing (Xmm) Lock Nut (mm ) TP Screw(3x0mm) Air tank Switch Rod (x300mm) Steel wire (0.5x500mm) Screw (x0mm) Nut (mm ) Washer(x5mm)
9 Keep the tailing some edge space and about the rudder. mm width between The sketch map after the rudder shaft assemble finished. Mount the fuel tank to the fuselage Tailing edge Rudder Make sure they are in the right position while installing. Cut away the rubber tube when the epoxy glue dried. mm Drill holes to the relevant position in the tailing edge and epoxy the rudder to them..5mm Drill a small hole to appropriate position in the fuselage for installing the plastical tube and a hole in the rudder for assembling the rudder shaft Steel wire Aluminum tube Washer(3x5mm) Washer(3x5mm) Screw (3x0mm) Steel wire (0.5x3000mm) The sketch map of the linkage for the rudder and the tail wheel. Install the servo. Screw (3x0mm) 33 Note: Customers can choose nylon stabbing fix the tank, We don t suppty nylon stabbing. 3 Install the servo. Set screw (3xmm) Washer (mm) Linkage Stopper Washer (mm) Washer (mm) Nut (mm) Set screw (3xmm) Assemble position in the the throttle fuselage. servo to appropriate B Assembly of the stabilizer. Pin hinge(xmm) U-style wire (50x5mm) Steel wire (0.5x3000mm) Matal douel (x) Make sure to glue securely. If not properly glued, a failure in flight may occur. Securely glue together.if coming off during flights, you'll lose control of your airplane which leads to accidents! Temporarily fasten down the main wing and check its correct position. A Rib template (mm ply) Stab joiner (x) Screw (x0mm) Nut (mm ) Washer(x5mm) Plastical tube(3x) A' B' A=A' B=B' Set the U-style wire through the enlargd hole as below. Plastical tube(3x) Screw (x0mm) Washer(x5mm) Ball joint Lock Nut (mm ) Steel wire 75mm 90mm 3mm Screw (x0mm) Nut (mm ) Washer(x5mm) Steel wire (0.5x3000mm) U-style wire (50x3mm) 0 7
10 3 According to the rib template drill holes to the tail of fuselage and assemble the "U"style wire as illustration. Trim slot to appropriate position in the stabilizer. Glue the elevator to the stabilizer by CA and epoxy. 7 Connect the elevator and the serer via the steel wire. mm x0mm Rib template (mm ply) Stab joiner (x) Elevator servo Stab joiner (x) Rib template (mm ply) Securely glue together. If coming off during flights, you 'll lose control of your airplane which leads to accidents! Drill and epoxy two holes the at wood the dowel stabilizer in them. root base via rib template 39 Apply instant type CA glue to elevator and pin hinge. 5 Install the servo. Rib template (mm ply) mm Wood dowel (x) Wood dowel (x) Pin hinge(xmm) Make sure hinges are mounted in the same line. 3mm Screw (x0mm) Washer(x5mm) Ball joint Lock Nut (mm ) Steel wire Screw (x0mm) Nut (mm ) Washer(x5mm) Pin hinge(.5xmm) Steel wire (0.5x3000mm) Washer(3x5mm) Screw (3x0mm) Plastical tube(3x) Screw (x0mm) Nut (mm ) Washer(x5mm) 3 0 Assemble the stabilizers carefully to the fuselage. 3 Keep some space about mm width between elevator and tailing edge. Assemble the elevator sever to appropriate position in the fuselage. Drill holes to appropriate position in the rudder and epoxy the ping hinges in them Tailing edge.5mm Elevator 0mm mm 5mm Securely glue together. If coming off during flights, you 'll lose control of your airplane which leads to accidents! Make sure they are in the right position while installing. Make sure hinges are mounted in the same line. Pin hinge(.5xmm) 3 9
T-28 Trojah INSTRUCTION MANUAL SAFETY PRECAUTIONS
T- Trojah Specification: Length :3 mm(3.5") Wing Span :057 mm(") Wing Area :70. sq. dm 7.55 sq. ft Wing Loading :7 g/sq. dm 39.5 oz/sq. ft Flying Weight :. kg( lbs) Radio :ch & servos Engine :0 -cycle
More informationHawker hurricane MK.IIa
Hawker hurricane MK.IIa Specification: Length :00 mm(") Wing Span :00 mm(") Wing Area :0. sq. dm.9 sq. ft Wing Loading :.9 g/sq. dm 5.9 oz/sq. ft Flying Weight :.kg(5 lbs) Radio :ch& servos Engine :0 INSTRUCTION
More informationSPITFIRE MK.XIV\XIX RUDDER
70 Adjustment. 7 The centre of the Gravity. Side View SPITFIRE MK.XIV\XIX RUDDER Top view 0mm 0mm 0mm Two wheel retract system Make sure to assemble retracts as instructed below. -way pressure inlet Strut
More informationFw-190 D9(50cc) INSTRUCTION MANUAL SAFETY PRECAUTIONS. Specification:
Fw-90 D9(50cc) Specification: Length: 00mm(8.5 ) Wing span: 093mm(8.5 ) Wing area: 77.79sq.dm(8.sq.ft) Wing loading: g/sq.dm(0oz/sq.ft) Flying weight: 9.5kg(0.9 bs) Radio: ch & 8servos Engine: 50cc gasoline
More informationPilatus PC-9 INSTRUCTION MANUAL SAFETY PRECAUTIONS. Specification:
Pilatus PC-9 Specification: Length: Wing span: Wing area: Wing loading: Flying weight: Radio: Engine: 9mm(7 ) 0mm(0 ) sq.dm(.9sq.ft) 0.g/sq.dm(.9oz/sq.ft).kg(7.bs) ch & servos 0 -cycle 0cc gasoline engine
More informationF - 4u Corsair (50cc)
F - u Corsair (50cc) Specification: Length: 73(.3") Wing span: 0mm(5") Wing area: 7.00sq.dm(9.39sq.ft) Wing loading: 35.g/sq.dm(.5oz/sq.ft) Flying weight:.kg(.0lbs) Radio: ch & 0servos Engine: 50cc gasoline
More informationFocke-Wulf Fw 190 RUDDER
7 Adjustment. 7 The centre of the Gravity. Side View Focke-Wulf Fw 90 RUDDER Top view 0mm 0mm 0mm Two wheel retract system Make sure to assemble retracts as instructed below. -way pressure inlet Strut
More informationP-47D Thunderbolt. Two wheel retract system Make sure to assemble retracts as instructed below. 3-way pressure inlet INSTRUCTION MANUAL
70 Adjustment. 7 The centre of the Gravity. Side View AILERON FLAP 0mm 0mm P-7D Thunderbolt AILERON FLAP 0mm 3mm Two wheel retract system Make sure to assemble retracts as instructed below. 3-way pressure
More informationAichi D3A1 INSTRUCTION MANUAL SAFETY PRECAUTIONS. Specification:
Aichi D3A Specification: Length: 50mm(0. ) Wing span: 057mm( ) Wing area: 7.sq.dm(.sq.ft) Wing loading: 99.9g/sq.dm(3.oz/sq.ft) Flying weight: 7.kg(.7lbs) Radio: ch & 7servos Engine: 0 -cycle C.G: 35mm
More informationF - 4u Corsair INSTRUCTION MANUAL SAFETY PRECAUTIONS. Two wheel retract system. Specification:
Adjustment. 3 The centre of the Gravity. Never fly before checking CG s required position. In order to obtain the CG specified reposition the receiver and battery. ELEVATOR Top view F - u Corsair 0mm 0mm
More informationB-25 Mitchell INSTRUCTION MANUAL SAFETY PRECAUTIONS
B-5 Mitchell Specification: Length :935 mm(76.") Wing Span :0 mm(95") Wing Area :77.6 sq. dm 7./sq.ft Wing Loading : g/sq. dm oz/sq. ft Flying Weight :0 kg(. lbs) Radio :6ch&3 servos Engine(a pair) :9
More informationJU-87D Stuka INSTRUCTION MANUAL SAFETY PRECAUTIONS
73 Adjustment. 7 Centre of Gravity. Side View AILERON FLAP 0mm 0mm JU-7D Stuka 30mm Top View AILERON FLAP 35mm 75 The front view when the drop tank and the bombs install completion. Specification: Length
More informationModellbau Lindinger GmbH Modellbau Lindinger GmbH
7 Adjustment. 7 Adjustment. AILERON 5mm 5mm RUDDER Robin 0 FLAP 0mm Top view 30mm 30mm Side View AILERON FLAP 73 Adjustment. ELEVATOR Side View 5mm 5mm Top view Position for right diagram. 7 Centre of
More informationBeaver INSTRUCTION MANUAL SAFETY PRECAUTIONS. 1.8mm. Specification:
9 Fix the aluminum bracket on the fuselage with screw. 95 The floats installation finished. Screw (x5mm) 9 Blind Nut (mm) 9 Washer (xmm) 9 Screw (x5mm) Beaver Damped nut (mm) Washer (xmm) Screw (x5mm)
More informationCessna 185 INSTRUCTION MANUAL SAFETY PRECAUTIONS
Cessna Specification: Length :0 mm(") Wing Span :00 mm(.") Wing Area :. sq. dm.9 sq. ft Wing Loading :7. g/sq. dm. oz/sq. ft Flying Weight :. kg(. lbs) Radio :ch&9 servos Engine :0 -cycle 0 -cycle INSTRUCTION
More informationSpitfire Mk.IX ARF. Electric retract system. TopRCModel-USA.com
Electric retract system Thank you very much for purchasing our TRCM optional electric retract set, all our products were passed strict QC before they shipped out to the customers. In order to avoid probably
More informationFOKKER D-VII INSTRUCTION MANUAL SAFETY PRECAUTIONS. Specification:
FOKKER D-VII Specification: Length Wing Span Wing Area :97 mm(55") :77 mm(70") :9sq.dm 9.sq.ft Wing Loading :59.g/sq.dm.9oz/sq.ft Flying Weight :.5kg(lbs) Radio Engine: :ch & 5servos :cc-cc INSTRUCTION
More informationCessna INSTRUCTION MANUAL SAFETY PRECAUTIONS. Specification:
Cessna - 95 Specification: Length Wing Span Wing Area :00 mm(") :7 mm(07") :0sq.dm.9sq.ft Wing Loading :75g/sq.dm.oz/sq.ft Flying Weight :9kg(9.lbs) Radio Engine: :ch & servos :0cc-50cc INSTRUCTION MANUAL
More informationAdrenaline. Specification: 5.5 sq. ft Wing Loading :82 g/sq. dm 26.9 oz/sq. ft Flying Weight :4.2 kg(9.3 lbs) :6ch&6 servos.
Adrenaline Specification: Length Wing Span Wing Area :70 mm(7") :70 mm(") :5. sq. dm 5.5 sq. ft Wing Loading : g/sq. dm.9 oz/sq. ft Flying Weight :. kg(9. lbs) Radio :ch& servos Engine :0 -cycle 0 -cycle
More informationLTR-14 TURNER SPECIAL
LTR- TURNER SPECIAL Specification: Length Wing Span Wing Area :05 mm(8") : mm(95") :sq.dm sq.ft Wing Loading :0g/sq.dm 5.oz/sq.ft Flying Weight :kg(.lbs) Radio Engine: :ch & 8servos :80cc-00cc INSTRUCTION
More informationAdmas A500. Specification:
Admas A500 Specification: Length :07 mm(8.7") Wing Span :00 mm(9.5") Wing Area :8.8 sq. dm 5.5 sq. ft Wing Loading :3 g/sq. dm 53.7 oz/sq. ft Flying Weight :8 kg(7.lbs) Radio :ch &3 servos Engine : -cycle
More informationZlin Z-526 AFS INSTRUCTION MANUAL SAFETY PRECAUTIONS. Specification:
Zlin Z-5 AFS Specification: Length Wing Span Wing Area :75 mm(7.") :05 mm(") :7.sq.dm.9sq.ft Wing Loading :70.9g/sq.dm.oz/sq.ft Flying Weight :5.kg(.9lbs) Radio :ch & servos Engine: :cc-cc INSTRUCTION
More information第 4 页. 3. Apply instand type AB glue to the holes in the aileron and hinges. Epoxy the aileron to the wing.
TopRCModel-USA.com TopRCModel-USA.com TopRCModel-USA.com Accessory list for the installation of aileron and flap. 3. Apply instand type AB glue to the holes in the aileron and hinges. Epoxy the aileron
More information105" TIGER MOTH ARF INSTRUCTION MANUAL VERSION 1.0
105" TIGER MOTH ARF INSTRUCTION MANUAL VERSION 1.0 Step 1. Installation of the aileron servos 1) Mount aileron servo to servo mounting blocks with servo s screws. Install servo mounting plate with screws.
More information第 4 页, 共 17 页. 3. Epoxy the wood block to the servo tray base on the mark line. Accessory part lists for wing installation.
第 1 页, 共 17 页 第 2 页, 共 17 页 第 3 页, 共 17 页 Accessory part lists for wing installation. 3. Epoxy the wood block to the servo tray base on the mark line. 1. Ready for assemble the wing servos. 4. Epoxy the
More informationFUSELAGE CONSTRUCTION
FUSELAGE CONSTRUCTION Note: prior to building and gluing on the work surface use protective covering on your building surface. (wax paper or clear wrap) Fit the laser cut Fuselage Front and Fuselage Rear
More informationSpecifications. Before commencing assembly, please read these instructions thoroughly.
INSTRUCTION MANUAL Before commencing assembly, please read these instructions thoroughly. Specifications Wing Span: 8.5 in / 30 mm Wing Area: 330 sq in /.3 sq dm Flying Weight: 6 oz / 70 g Fuselage Length:
More informationEXTRA 330SC 60CC. Item No:H G Specifications cc gas DA50,DA60, DLE55, DLE60(twin), 3W55. Description
EXTRA 330SC 60CC Item No:H G060011 Specifications Wing Span Length Wing Area Flying Weight Gasoline Radio Description Carbon Fibre : 92" (2347mm) 84 1/2 " (2060mm) 1526.8 sq in(98.5sq dm) 16 17lbs(7300
More informationLANDING GEAR. 1. Fit landing gear into slots on bottom of fuselage.
LANDING GEAR 1. Fit landing gear into slots on bottom of fuselage. 4. Use channel-lock pliers to press blind nuts into position (note: drilled hole should be slightly smaller than shaft of blind nut for
More informationMECOA EZ-4061 Trainer
MECOA EZ-4061 Trainer EZ-4061 is a newly designed, Almost Ready to Fly kit. It is an extremely easy to control trainer with strong construction and excellent aerodynamic performance. This is a great choice
More informationCorvus Racer CC
Corvus Racer 540 35CC Item No:L-G035008 Specifications Wing Span Length Wing Area Flying Weight Glow Gasoline Electric Radio mm mm 1200sq in (77.4sqdm) 9.9-12lbs(4.5-5.5kg) 91-1.20(2C) 1.10-1.40(4C) 20-40cc
More informationSpecifications. Before commencing assembly, please read these instructions thoroughly. INSTRUCTION MANUAL
INSTRUCTION MANUAL Before commencing assembly, please read these instructions thoroughly. Specifications Wing Span: 50 in / 170 mm Wing Area: 484 sq in / 31. sq dm Flying Weight: 3.5 lbs / 1600 g Fuselage
More informationTIGER MOTH 120 ASSEMBLY INSTRUCTIONS
TIGER MOTH 120 ASSEMBLY INSTRUCTIONS SPECIFICATIONS Wing Span: Length: Radio: Flying Weight: 1920mm 1580mm 4 channel with 6 servos 4200g AILERON ASSEMBLY 1 Start by removing the servo cover from the bottom
More informationAure. Radio required : 3 channels, 4 servos airplane radio. Specifications. * Specifications are subject to change without notice.
A L M O S T- R E A D Y- T O - F LY Aure INSTRUCTION MANUAL Radio required : 3 channels, 4 servos airplane radio Specifications Wing Span Wing Area Flying Weight Fuselage Length 81.5 in / 2070mm 572.0 sq
More informationSkymaster ARF F-18E Instructions Manual
Skymaster ARF F-18E Instructions Manual first: Take out the front servos mount, install front fuel tank before installing nose cone connect nose cone to fuselage by 6 screw Take out the 6 screws and Bottom
More informationEdge 540 V3 35CC. Scheme A. Item No:L G Specifications. Flying Weight
Edge 540 V3 35CC Item No:L G035016 Specifications Wing Span Length Wing Area Flying Weight Glow Gasoline Electric Radio Description 76 (1930mm) 74 (1879mm) 1200sq in(77.4sqdm) 9.9 12lbs(4.5 5.5kg) 91 1.20(2C)
More informationINSTRUCTION MANUAL. Specifications. Wing Area Flying Weight Fuselage Length. 28 oz / 800 g 30.0 in / 760 mm
ALMOST-READY-TO-FLY INSTRUCTION MANUAL Requires : -channel radio w/ micro servos, Outrunner Motor w/ Propeller Adaptor 0A Brushless ESC, 3 cells 11.1V 100 mah Li - Po battery & charger. Wing Span Wing
More informationMXS R 30CC. Item No:L G Specifications. 67 1/2"(1720mm) (2C) (4C) 26 35cc gas DLE 30/35RA MLD35 JC30Evo.
MXS R 30CC Item No:L G030008 Specifications Wing Span Length Wing Area Flying Weight Glow Gasoline Electric Radio Description Covering Material Carbon Fibre : 75"(1915mm) 67 1/2"(1720mm) 1023sq in(66sq
More informationAT channel 6 servos
Wing Span: Wing Area: Fuselage Length: Flying weight: Power system: Radio: 60.7in/1540mm 561 sq in/36.3 sq dm 44.1in/1120mm 6.9 Ibs/ 3100g 46(2C0/71(4C) 5 channel 6 servos AT6-46 INSTALLING AILERONS Begin
More information30% Edge 540T Almost Ready to Fly
Lanier R/C 30% Edge 540T Almost Ready to Fly WARNING! THIS IS NOT A TOY! THIS IS NOT A BEGINNERS AIRPLANE This R/C kit and the model you will build from it is not a toy! It is capable of serious bodily
More informationExtra 330LT CC. 2 Colour schemes H-G120001A ORACOVER FERRARI RED # ORACOVER WITH # ORACOVER BLACK # ORACOVER SILVER #
Extra 330LT 85-125CC Item No:A-G120001 Specs: WING SPAN: LENGTH: WING AREA: FLYING WEIGHT: ENGINE: RADIO: Description Covering Material Carbon Fibre: 111 (2833mm) 100" (2530mm) 2139sq in (138sq dm) 25.3-28lbs
More informationCitabria Pro. Aerobatic Parkflyer. by Joel Dirnberger
Citabria Pro Aerobatic Parkflyer by Joel Dirnberger Revision C: December 21, 2004 Citabria Pro Building Instructions Length: Wingspan: Wing Area: Flying Weight: Wing Loading: Functions: Specifications:
More informationInstruction Manual. Specification:
Instruction Manual H I G Specification: Wingspan: 133 cm (52.3 inches) Length : 104 cm (40.9 inches) Weight : 1830gr Engine : 25-32 two stroke Radio : 4 channel - 4 servo H W I N G KIT CONTENTS: We have
More informationInstruction Manual book
Instruction Manual book ITEM CODE BH53. SPECIFICATION Wingspan : 1,250mm 49.21 in. Length : 930mm 36.61in. Weight : 1.1kg 2.42 Lbs. Parts listing required (not included). Battery: 3 CELLS-LI-POLY-11.1V-2,500
More informationRYAN STA SAFETY PRECAUTIONS. "Sport Scale E-Power ARF" For Intermediate and Advanced Fliers. This radio control model is not a toy!
RYAN STA "Sport Scale E-Power ARF" For Intermediate and Advanced Fliers. SAFETY PRECAUTIONS This radio control model is not a toy! First-time builders should seek advice from people with model building
More informationCorvus Racer Colour schemes. AeroPlus RC Copyright 2013 All Rights Reserved
Corvus Racer 540 59 Item No:A E050003 Specifications WING SPAN: 59"(1500mm) LENGTH: 54.1"(1374mm) WING AREA: 654sq.in.(42.2sq.dm.) FLYING WEIGHT: 4.6 5.3lbs(2000 2300g) Electric:Brushless outrunner 8Oz.
More informationVIPER 140 Manual. Release 1.0 January 2018
VIPER 140 Manual Release 1.0 January 2018 Please read this user manual carefully, it contains instructions for the correct assembly of the model. Please refer to the web site www.harlock-rc.com for updates
More informationINSTRUCTION MANUAL BOOK.
INSTRUCTION MANUAL BOOK. SPECIFICATION Wingspan : 164 cm 64.57in. Length : 135 cm 53.15 in. Weight : 3.3kg 7.26 lbs. Servo : 7 servos. Radio : 4 channels. Engine : 61 cu.in-2 stroke. 91 cu.in-4 stroke.
More informationRESolution V2 Manual
RESolution V2 Manual Note for the German Manual: Yellow Bottle thick CA Pink Bottle Med CA Blue tube 5 minute Epoxy Green tube 90 Minute Epoxy Construction of the Fuselage Step 1: Cover the plan with a
More informationBOOMERANG TORUS. Aerobatic Sport Jet for 20 to 34 lbs (P80 to P160) thrust turbines.
BOOMERANG TORUS Aerobatic Sport Jet for 20 to 3 lbs (P80 to P160) thrust turbines. Specifications: Span... 83" (2209mm.) Span with Wingtip Tanks 90" (2286mm.) Length...87" (2108mm.) Weight 29 Lbs.(13.15
More informationPERCIVAL P-56 PROVOST
Instruction Manual Book. PERCIVAL P-56 PROVOST OLEO STRUTS LANDING GEAR. ALL BALSA - PLY WOOD CONSTRUCTION. COVERED WITH ORACOVER Glow and EP 95% ALMOST READY TO FLY SPECIFICATION: - Wingspan: 1,644mm
More information90 WING SPAN P-51D MUSTANG (COPYRIGHT PROTECTED 2014) ALL RIGHTS RESERVED
90 WING SPAN P-51D MUSTANG (COPYRIGHT PROTECTED 2014) ALL RIGHTS RESERVED GENERAL INSTRUCTIONS This design is basically an enlargement of the very popular fun scale Mustang 60 Size. You can build it light
More informationFAIREY ALBACORE. Instruction Manual Book. Glow and EP. Item code: BH % ALMOST READY TO FLY SPECIFICATION:
Instruction Manual Book. FAIREY ALBACORE ALL BALSA - PLY WOOD CONSTRUCTION. COVERED IN A HEAT-SHRINK FILM WITH PRINTED. Glow and EP 95% ALMOST READY TO FLY SPECIFICATION: - Wingspan: 1,693mm (66.65in).
More informationBUILDING THE A6M2 ZERO
BUILDING THE A6M2 ZERO Product Support (Do Not Remove From Department) TOP FLITE MODELS, INC CONGRATULATIONS' You now own the most accurate R/C Stand-Off Scale kit ever produced We at Top Flite hope that
More information96 WING SPAN SPITFIRE (COPYRIGHT PROTECTED 2014) ALL RIGHTS RESERVED
96 WING SPAN SPITFIRE (COPYRIGHT PROTECTED 2014) ALL RIGHTS RESERVED GENERAL INSTRUCTIONS Should you elect to use the recommended Door Skin, which is 1/8 mahogany plywood measuring 36 x 88. Have it cut
More informationRADIO CONTROL MODEL / RC FLUGMODELL INSTRUCTION MANUAL
RADIO CONTROL MODEL / RC FLUGMODELL INSTRUCTION MANUAL SPECIFITIONS Wingspan...57.5 in. / 146cm Length...50 in. / 127cm Engine...46 2T /.70 4T or Electric equivalent. Radio...4 ~ 6 channel Almost ready
More informationFUJI FA-200 AERO SUBARU
FUJI FA-200 AERO SUBARU SEMI SCALE SPORT MODEL AERO SUBARU Assembly and Operations Manual Please review this manual throughly Before assembling or Operating The AERO SUBARU Semi scale sport model We ve
More informationHigh performance 90mm fiberglass jet
High performance 90mm fiberglass jet Assembly manual For intermediate and advanced fliers only! Specs Wingspan: 1255mm Fuselage length: 1250mm Flying weight: 2600-3000g Wing area: 22.6 dm² Wing loading:
More informationInstruction Manual. Item No: AL001
Instruction Manual Item No: AL001 Specifications: Wingspan: 2037mm (80.2 in) Length: 1677mm (66 in) Wing Area: 65.5dm2 (1015.3 sq in) Flying Weight: 7.6kg (16.7 lbs) Engine(not incl.): 45-50cc Gas Radio(not
More informationTWEETY 25 INSTRUCTION MANUAL. Almost Ready to Fly Nitro/Electric Aerobat FEATURES SPECIFICATIONS
TWEETY 25 Almost Ready to Fly Nitro/Electric Aerobat INSTRUCTION MANUAL SPECIFICATIONS FEATURES WINGSPAN: 45.7 (1160mm) LENGTH: 38.6 (980mm) WING AREA: 370 sq in(24 sq dm) FLYING WEIGHT: Approx. 3.3 lbs
More informationC-180 Builder s Manual
C-180 Builder s Manual. May 20, 2002 Last revised July 11, 2002 Copyright! 2002 Douglas Binder, Mountain Models www.mountainmodels.com sales@mountainmodels.com (719) 630-3186 1 Required Equipment! Xacto
More informationAssembly Instructions. Stinger 120. Almost Ready to Fly
Stinger 120 Almost Ready to Fly Important Information: Please inspect the plane before beginning to assemble to make sure you are happy with it. After assembly has begun you cannot return the kit. If you
More informationJUNKERS JU87- B2 STUKA
Instruction Manual Book Item code: BH169. JUNKERS JU87- B2 STUKA OLEO STRUTS LANDING GEAR. ALL BALSA - PLY WOOD CONSTRUCTION. COVERED IN A HEAT-SHRINK FILM WITH PRINTED. 95% ALMOST READY TO FLY SPECIFICATION:
More informationVelocity Slingjet. Specifications: Construction Span Length Take-off weight w/ gear. Balsa/foam/film 1055m m (41.54 ) 1040m m (40.
Velocity Slingjet Specifications: Construction Span Length Take-off weight w/ gear Recommended servos w/o nose-steering Recommended fan Recommended motor Recommended controller Balsa/foam/film 1055m m
More informationSuper Sky Surfer 2000 Assembly Instructions
Super Sky Surfer 2000 Assembly Instructions Note: Plug and Play version of the Sky Surfer comes with fuselage pre-glued and motor/servos installed. If you wish to route antennas or wires through the tail,
More informationBUCKER BU 131 JUNGMANN ALL BALSA - PLY WOOD CONSTRUCTION. COVERED WITH ORACOVER
Instruction Manual Book. BUCKER BU 131 JUNGMANN ALL BALSA - PLY WOOD CONSTRUCTION. COVERED WITH ORACOVER Glow and EP 95% ALMOST READY TO FLY SPECIFICATION: - Wingspan: 1,850 mm (72.83 in). Length: 1,660
More informationF3A -70E ASSEMBLY MANUAL
F3A -70E ASSEMBLY MANUAL The new F3A-70E, was designed in an extremely lightweight structure, the all wood airframe, and the new revolutionary Lift Generator on landing gear give the F3A-70E an impressive
More informationPROCTOR. Instruction Manual Book 95% ALMOST READY TO FLY. Item code: BH154. SPECIFICATION ALL BALSA - PLY WOOD CONSTRUCTION. COVERED WITH ORACOVER
Instruction Manual Book PROCTOR Item code: BH154. ALL BALSA - PLY WOOD CONSTRUCTION. COVERED WITH ORACOVER 95% ALMOST READY TO FLY SPECIFICATION Wingspan: 1,360 mm (53.54 in). Length: 1,480 mm(58.27 in).
More informationSPUNKY ASSEMBLY MANUAL
SPUNKY ASSEMBLY MANUAL Please read the tips section at the back of this manual regarding the use of laser cut parts. The proper removal and preparation of these parts is important. When laser cut, some
More information94 Yak 54 ARF WARNING
94 Yak 54 ARF WARNING A radio-controlled model is not a toy and is not intended for persons under 16 years old. Keep this kit out of the reach of younger children, as it contains parts that could be dangerous.
More informationMUSTANG P-51. Hand-made Almost Ready to Fly R/C Model Aircraft ASSEMBLY MANUAL
MUSTANG P-51 Hand-made Almost Ready to Fly R/C Model Aircraft ASSEMBLY MANUAL Specifications Wingspan---------------------------------------- 60.5 in----------------------- 153.7cm. Wing area-------------------------------------
More informationTHE APOGEE A 100-INCH AMA DURATION SAILPLANE FROM DYNAFLITE
THE APOGEE A 100-INCH AMA DURATION SAILPLANE FROM DYNAFLITE Apogee is the intermediate sailplane designed to be competitive in AMA duration contests. Effective spoilers, rudder and full flying stabilizer
More informationDORNIER DO 27 SEMI SCALE SPORT MODEL DORNIER DO 27. Assembly and Operations Manual
DORNIER DO 27 SEMI SCALE SPORT MODEL DORNIER DO 27 Assembly and Operations Manual Please review this manual throughly Before assembling or Operating The DORNIER DO 27 Semi scale sport model We ve used
More informationHand-made Almost Ready to Fly R/C Model Aircraft ASSEMBLY MANUAL
Hand-made Almost Ready to Fly R/C Model Aircraft ASSEMBLY MANUAL Specifications Wingspan -----------------------.148 cm--------------- 58.3 in. Wing area ----------------------- 3474sq. cm ---- 538.4sq
More informationLANIER - Giles % - INSTRUCTIONS
Additional Parts Required (4) or more channel radio with 4 servos..25 -.36 two stroke or.40 -.52 four stroke engine Appropriate Master Airscrew prop and Hayes mount for your engine. 2-1/2 Tru-Turn spinner
More informationLANIER - Ultimate Pitts - INSTRUCTIONS. Additional Parts Required. (12) 4-40 blind nuts (Dubro #606)
Additional Parts Required (4) or more channel radio with 7-8 servos..91-2.2 two stroke or 1.20-1.84 four stroke engine Appropriate Master Airscrew prop and Hayes mount for your engine. 3 Tru-Turn spinner
More informationHIGH-END TECHNOLOGY. Electric ducted fan Starfighter
HIGH-END TECHNOLOGY RC Electric ducted fan Starfighter First we want to thank and congratulate you with your decision in buying one of our Kits. The Starfighter puts together very easily so there is not
More informationAssembly Instructions STINGER
STINGER 120 ARF Important Information: Please inspect the plane before beginning to assemble to make sure you are happy with it. After assembly has begun you cannot return the kit. If you find a problem
More informationLANIER - Double Trouble - INSTRUCTIONS. Tail 1 T1 ¼ Balsa 1 T2 ¼ Balsa 2 T3 ¼ Balsa 1 T4 ¼ Balsa 1 T5 ¼ Balsa 1 T6 ¼ Balsa 2 J1 ¼ Balsa 2 J2 Lite ply
Tail 1 T1 ¼ Balsa 1 T2 ¼ Balsa 2 T3 ¼ Balsa 1 T4 ¼ Balsa 1 T5 ¼ Balsa 1 T6 ¼ Balsa 2 J1 ¼ Balsa 2 J2 Lite ply Other Parts 2 Aluminum Gear 1 3/32 Music wire tail skid 2 Elevator and J-plane joiner wire
More informationE-AERO EPP PITTS KIT From BP HOBBIES. Parts Included in kit
E-AERO EPP PITTS KIT From BP HOBBIES Parts Included in kit Thank you for purchasing the BP Hobbies/E-aero EPP Pitts. Please take the time to read through the instruction manual before beginning the build.
More informationNOORDUYN NORSEMAN. Instruction Manual Book 95% ALMOST READY TO FLY. Item code: BH157. SPECIFICATION
Instruction Manual Book Item code: BH157. NOORDUYN NORSEMAN ALL BALSA - PLY WOOD CONSTRUCTION. COVERED WITH ORACOVER. 95% ALMOST READY TO FLY SPECIFICATION - Wingspan: 1840 mm (72.44 in). - Length: 1180
More informationSig Mfg. Co., Inc South Front Street...Montezuma, Iowa 50171
Sig Mfg. Co., Inc...401-7 South Front Street...Montezuma, Iowa 50171 Introduction The SEALANE takes off and lands on water just as easy as the Sig Kadet LT40 does on solid ground. Gentle, graceful, sure
More informationHAWKER HURRICANE. Instruction Manual Book 95% ALMOST READY TO FLY. Item code: BH147. SPECIFICATION
Instruction Manual Book Item code: BH147. HAWKER HURRICANE ALL BALSA - PLY WOOD CONSTRUCTION. COVERED IN A HEAT-SHRINK FILM WITH PRINTED. 95% ALMOST READY TO FLY SPECIFICATION Wingspan: 1,520 mm (59.84
More informationAviator Trainer40 ARF Instruction Manual Specifications
Aviator Trainer40 ARF Instruction Manual Specifications Wingspan: 65.0 in (1650 mm) Length: 53.1 in (1350 mm) Wing Area: 729sq in (47.0 sq dm) Flying Weight: 5.3 lbs (2400g) Dear Customer, Congratulations
More informationAssembly Manual PARTS DRAWING
PARTS DRAWING AS670 Set Float () Assembly Manual AS670 Water Rudder Set AS67 Mounting Bracket Set Plug().x3mm Rivet().6x8mm Wood Screw() Plug w/rudder Bush () Rudder Shaft() Steering Arm() Water Rudder()
More informationASSEMBLY & OPERATIONS MANUAL
TM TM AERO SUBARU 40-52 ARF ECS SEMI SCALE MODEL WITH POLYCOTE ECS ENHANCED GRAPHICS SYSTEM #VMA-S140B (blue as shown) #VMA-S140R (red) This model may be produced in a number of different graphic schemes
More informationSTEP 1 STEP 2 STEP 3. Page 2
INSTRUCTION MANUAL Congratulations on your purchase of the Bullet ARTF - the first Almost Ready to Fly version of this classic lowwinger. Based on the original and timeless Bullet design, the new Ripmax
More informationDORNIER DO 27 SEMI SCALE SPORT MODEL DORNIER DO 27. Please review this manual throughly Before Assembling or Operating The DORNIER DO 27
DORNIER DO 27 SEMI SCALE SPORT MODEL DORNIER DO 27 Assembly and Operations Manual Please review this manual throughly Before Assembling or Operating The DORNIER DO 27 Semi Scale Sport Model We ve used
More informationThunder Tiger Ace Hobby Page 1 6/8/10
TOC 35% Katana Assembly Manual Thunder Tiger Ace Hobby Page 1 6/8/10 Table of contents Thunder Tiger Contact Information Page 3 Introduction.Page 4 Kit Contents.Page 5 Items Needed to Complete...Page 6
More informationRyan STA Sport Scale Model Aircraft Assembly and Instruction Manual
Ryan STA Sport Scale Model Aircraft Assembly and Instruction Manual Warning: This radio controlled model is not a toy. It requires skill to fly and is not recommended for the novice pilot. It should not
More informationSZD-10 bis CZAPLA ASSEMBLY MANUAL IN PICTURES
1 RUDDER Plan and parts: 2 Assembly steps: Photo above: glue together rudder spar, ribs and trailing edge. Clamp spar to a flat surface (chipboard on the photo) and make sure the straight aligment of the
More informationBashing The Hanger 9 Cessna 182 ARF Part 4
Bashing The Hanger 9 Cessna 182 ARF Part 4 Eric Helms Pongo Air This is the final installment of a four-part article covering a variety of modifications incorporated into a Hanger 9 Cessna 182 ARF. Upgrades
More informationINSTRUCTIONS FOR FINAL ASSEMBLY
MS: 11 INSTRUCTIONS FOR FINAL ASSEMBLY Graphics and specfications may change without notice. Specifications: Wingspan -------------------------------------------- 156 cm, 61.42 in. Wing area ---------------------------------
More information(Build Instructions)
(Build Instructions) Specifications * Wingspan: 58cm * Length: 50cm * Flying Weight: 59 grams * Channels: 3 (Rudder Elevator Throttle) * Suggested Receiver: 4Ch Micro * Motor: 8mm GearDrive * Prop: GWS
More informationHot Stik ARF WARNING. Copyright 2005 Carl Goldberg Products LTD CARL GOLDBERG PRODUCTS, LTD.
Hot Stik ARF INSTRUCTIONS WARNING A radio-controlled model is not a toy and is not intended for persons under 16 years old. Keep this kit out of the reach of younger children, as it contains parts that
More informationREX SCOUT D6. R/C Scale Model Instructions
REX SCOUT D6 R/C Scale Model Instructions CONTACT INFORMATION The Rex Scout D6 was designed by M.K. Bengtson Manufactured and Distributed by: Bengtson Company e-mail: sales@aerodromerc.com Web Site: www.aerodromerc.com
More informationHIGH-END TECHNOLOGY. Electric ducted fan rafale
HIGH-END TECHNOLOGY RC Electric ducted fan rafale First we want to thank and congratulate you with your decision in buying one of our Kits. The Rafale puts together very easily so there is not much explanation
More information67 Edge 540 ARF WARNING
67 Edge 540 ARF INSTRUCTIONS WARNING A radio-controlled model is not a toy and is not intended for persons under 16 years old. Keep this kit out of the reach of younger children, as it contains parts that
More informationSbach 1,2m 3D/aerobatic EPP model Building instructions
Sbach 1,2m 3D/aerobatic EPP model Building instructions Please refer to the Diagram sheet Diagrams A, B Press 2 carbon strips (1x3x1000 mm) into the grooves in the sides of the fuselage central part (the
More informationBuilding a Giant Scale Electric EINDECKER Part 2
Building a Giant Scale Electric EINDECKER Part 2 John Bernard N1KUB AMA 58903 IMAA 28971 In Part-1 of this series, we explored the 100 Eindecker kit from SR Batteries and started building the fuselage.
More information