INSTALLATION INSTRUCTIONS 480-4SBB / 480-6SBB SURFACE MOUNT BOX w/battery COMPARTMENT
|
|
- Kathryn Williams
- 5 years ago
- Views:
Transcription
1 480-4SBB / 480-6SBB SURFACE MOUNT BOX w/battery PARTMENT 4-5/8 [117mm] 1-3/4 [44mm] 4X HOLES 4-5/8 [117mm] 4X INTEGRAL PINS BATTERY PARTMENT ACCESS COVER BLACK ABS MATERIAL BOX EQUIPPED FOR WIRED OR WIRELESS APPLICATION. USED WITH 4-1/2 SQ. AND 6" SQ. ES P:\INSTALLATION INST\WIKK\INST-480-4SBB_6SBB.vsd REV Page 1
2 480-4SSB / 480-6SBB INSTRUCTIONS (HARD WIRED and WIRELESS) 1) Break out the battery compartment access cover from the back of the box and install it into the open area in the side wall located at the bottom of the box, as it will hang on the wall. When the access cover is in the closed position, the slot in the cover will face out and be closest to the switch. When installed correctly, the door slides smoothly and will be held in place by the mounting plate. If needed, drill a small weep hole in the bottom of the box (as it hangs) to allow moisture to evaporate. 2) Use appropriate screws (not supplied) to mount the box to the wall surface at the 4 open mounting hole positions. 3) If you are using a wireless transmitter, attach the transmitter to the back of the box using the included double sided tape. Connect the battery terminals to the battery and install into the battery compartment. Program the transmitter to match the receiver. 4) For either Hard-wired or Wireless setups, connect the lead wires to the switch at the and contacts. 5) Fit the 6-32 x 5/8 socket cap screws from the switch parts bag into the 4 integral mounting pins located at the upper and lower 2-gang positions. 6) Hang the wall switch onto the socket cap screws and tighten down with the allen wrenches provided in the parts bag or with the handle grip allen wrenches. Alternate the tightening of the screws a few turns at a time each from the top to bottom. P:\INSTALLATION INST\WIKK\INST-480-4SBB_6SBB.vsd REV Page 2
3 480-4SB & 480-4FB SQUARE SURFACE/FLUSH MOUNT BOX FOR 4-1/2 ES CROSS SECTIONAL VIEWS HOLLOW WALL SURFACE MOUNT SOLID WALL SURFACE MOUNT HOLLOW WALL FLUSH MOUNT HOLLOW WALL ANCHOR BOX BOX BOX ADJUSTMENT SCREW FLUSH MOUNT BRACKET SOLID WALL ANCHOR ILLUSTRATION #1 ILLUSTRATION #2 Parts included with mounting boxes: >Black ABS surface or flush mount box >Transmitter mounting pins >9V battery mounting clip >Mounting instructions >Weather resistant gasket 480-4SB SURFACE MOUNT: Hollow Wall or Solid Wall (illustration #1) 1] Drill pilot holes in mounting box (placement indications are in box). 2] Drill pilot holes in mounting surface. 3] Insert appropriate fastener (screw, toggle, etc.) through box and into mounting surface; tighten. 4] Insert Weather Resistant Gasket. 5] Complete installation of switch FB FLUSH MOUNT: Hollow Wall ONLY (illustration #2) 1] Cut 5-5/8 x 5-5/8 access hole into mounting surface. 2] Insert box into the hole. 3] use the two Phillips head screws to tighten the silver hanger to the mounting surface. 4] Insert Weather Resistant Gasket. 5] Complete assembly of the switch. P:\INSTALLATION INST\WIKK\INST-480-SQ.vsd REV Page 1
4 480-4FB 6-3/4 X 6-3/4 x 2-1/8 (172mm x 172mm x 55mm) 1-7/8 Inside Depth (48mm) Used with 4-1/2 X 4-1/2 switches ADJUSTMENT SCREW INSTALL BATTERY CLIP HERE FLUSH MOUNT BRACKET Mounting bracket for hollow walls. Flush mount black ABS material for wireless or hardwired applications; Wireless use requires RF-Transparent walls. 15 PIN LOCATIONS FOR TRANSMITTER LOCATIONS Repositionable mounting pins for transmitter placement Weather resistant gasket is included and must be used with 4-1/2 x 4-1/2 switches. Weather resistant gasket Back side view For surface mount use 480-4SB P:\INSTALLATION INST\WIKK\INST-480-SQ.vsd REV Page 2
5 480-4SB 5-1/2 x 5-1/2 (140mm x 55mm) 1-7/8 Inside depth (48mm) Used with 4-1/2 x 4-1/2 switches INSTALL BATTERY CLIP HERE 15 PIN LOCATIONS FOR TRANSMITTER Surface mount black ABS material for wireless or hardwired applications. Repositionable mounting pins for transmitter placement LOCATIONS Weather resistant gasket is included and must be used with 4-1/2 x 4-1/2 switches. For flush mount use 480-4FB Weather resistant gasket Back side view P:\INSTALLATION INST\WIKK\INST-480-SDC.vsd REV Page 3
6 482A2U SINGLE GANG PUSH PLATE PUSH TO OPEN, SPDT 2-3/4 [69.85mm] 7/16 [11.10mm] 7/8 [22] MIN STD 4-1/2 [114.30mm] Specifications GRAIN DIRECTION Physical Size: 2-3/4 W X 4-1/2 H x 1-5/16"D Switch mounts to a Single Gang (2" x 4") or Double Gang (4" x 4") electrical box Contact Type: 482A2U = SPDT Contact Rating: 2 15 P:\INSTALLATION INST\WIKK\INST-482A2U.vsd REV Page 1
7 484O4U DPDT SQUARE PUSH PLATE, PUSH TO OPEN, 4-1/2 4-1/2 [114] TYP 1-1/2 [38] FOR 2 POLE 19/32 [15] Specifications GRAIN DIRECTION Physical Size: 4-1/2"sq x 2-3/32"D Switch mounts to a Single Gang (2"x4") or Double Gang (4"x4") electrical box Contact Type: DPDT Contact Rating: 2 15 P:\INSTALLATION INST\WIKK\INST-484O4U.vsd REV Page 1
8 484O2U SINGLE GANG PUSH PLATE PUSH TO OPEN - DPDT 2-3/4 [69.85mm] 7/16 [11.10mm] 1-1/2 [38] FOR 2 POLE 4-1/2 [114.30mm] Specifications GRAIN DIRECTION Physical Size: 4-1/2" x 2-3/4 x 1-15/16 "D Switch mounts to a Single Gang or 2" x 4" electrical box Contact Type: DPDT Contact Rating: 2 15 P:\INSTALLATION INST\WIKK\INST-484O2U.vsd REV Page 1
9 484A4U SQUARE PUSH PLATE, PUSH TO OPEN, 4-1/2 DPDT 4-1/2 [114] 4-1/2 [114] PUSH TO TO OPEN 1-1/2 [38] FOR 2 POLE Specifications GRAIN DIRECTION GRAIN DIRECTION 19/32 [15] Physical Size: 4-1/2"sq x 1-15/32"D Switch mounts to a Single Gang (2"x4") or Double Gang (4"x4") electrical box Contact Type: DPDT Contact Rating: 2 15 P:\INSTALLATION INST\WIKK\INST-484A4U.vsd REV Page 1
10 482A4RU ROUND PUSH PLATE, PUSH TO OPEN 4-1/2 SPDT 4-1/2 [114] PUSH TO OPEN 7/8 [22] MIN STD 19/32 [15] Specifications Physical Size: 4-1/2" Dia x 1-15/32"D Switch mounts to a Single Gang (2"x4") or Double Gang (4"x4") electrical box Contact Type: SPDT Contact Rating: 2 15 P:\INSTALLATION INST\WIKK\INST-482A4RU.vsd REV Page 1
11 6.000" [152.40].188" [4.76] 7.604" [ ] 6.000" [152.40] BPG6SPV SQ. POST INGROUND TOUCH PREP " SQUARE POST TAMPER RESISTANT SECURITY SCREWS IN INGRESS R CAP BLACK RF TRANSPARENT BOLLARD CAP.188" [4.76] 1.5" DIAMETER HOLE IN BASE FOR ELECTRICAL CONDUIT 4-40 SET SCREWS FOR SECURING BOLLARD CAP BOLLARD MATERIAL: ALUMINUM TYPE 6063-T5 STAINLESS STEEL TYPE " [1,072] " [1376] " [914.40] ACTUATING COLUMN AVAILABLE FINISHES: ALUMINUM; ANOIDIZED CLEAR (628), DARK BRONZE, (710) LIGHT BRONZE, BLACK (711) AND MILL FOR PAINTING OR POWDER COATING. STAINLESS STEEL; US32D (630) SATIN, US32 (629) MIRROR INGRESS R MATERIAL: ALUMINUM TYPE 6063-T5 STAINLESS STEEL TYPE 304 BRASS TYPE 464 AVAILABLE FINISHES: ALUMINUM; ANOIDIZED CLEAR (628) AND DARK BRONZE (710) STAINLESS STEEL; US32D (630) SATIN, US32 (629) MIRROR GRADE LINE BRASS; US4 (606) SATIN UNCOATED, US3 (605) MIRROR UNCOATED " [305] 3.000" [76.20] P:\INSTALLATION INST\WIKK\INST-BPG6SPV.vsd REV Page 1 NEC CLASS II CIRCUIT (BY OTHERS) TO SEAL AGAINST GROUNDWATER, CONDENSATION REMOVE BOLLARD CAP AND THROUGH THE TOP OF BOLLARD, POUR 10lb BAG OF DRY PREMIXED PATCHING OR QUICKSET CEMENT (NOT COURSE AGGREGATE TYPE) INTO THE BOTTOM OF BOLLARD. LIFT BOLLARD SLIGHTLYTO MAKE SURE SOME DRY CEMENT SETTLES AROUND OUTSIDE OF BOLLARD. SPRINKLE WITH REMENDED AMOUNT OF WATER PER CEMENT INSTRUCTIONS.
Straight Stringer Installation Instructions
Straight Stringer Installation Instructions Floor-to-Wall Installation F L I G H T P L A N Unpack: What s included? Your Stringer Tread Screws (8) per tread (1) Torque Wrench (1) Socket (for the brackets
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS HIGH PRESSUE LAMINATE (HPL) TOILET PARTITIONS 1030 TrimLineSeries 1040 DesignerSeries Includes continuous hardware option.65. IMPORTANT: Storage and Handling Information on last
More informationBol FEATURES: SPECIFICATIONS: 8' 24' Round Tapered and Straight Wood Poles STRUCTURA INC. FIXTURE TYPE: PROJECT NAME:
Bol 8' 24' Round Tapered and Straight Wood Poles FIXTURE TYPE: PROJECT NAME: Round Taper Glulam solid wood and aluminum pole available in 8' 24' lengths. Tenon adapters, slip fitters and side bracket mounts
More informationOriginal Gallery System
GAllery System Art Displays Original Gallery System a Gallery System product Here s everything you need to know to get started with your Gallery System Art Hanging System GS getting started To install
More informationTop Mount Ultra Modern Hanger
Top Mount Ultra Modern Hanger ASSEMBLY INSTRUCTIONS TOP MOUNT ULTRA MODERN HANGER Recommended Tools Level Tape Measure Pencil Drill with 1/8, and 1/4, Drill Bits and Phillips Bit Socket Wrench with 9/16
More informationINS T A L L A TIO N INS T R U C TIO N S. Ceiling Mount Track System
Ceiling Mount Track System 10.26.2016 Specifications Ceiling Post: Unassembled 2-7/8 Assembled 1-11/16 7/8 7-9/16 5-7/8 3/8 2 Tubes 1/2 2-3/8 5 Parts and Tools Tools Needed Tape Measure Pencil Drill with
More informationQuill Stop V2 Installation Guide 11/16/2014
Thank you for purchasing the Quill Stop for the Sieg X3 (Grizzly G0463) and SX3 (Grizzly G0619) mills. Your feedback is always appreciated. Please email questions and comments to gregpriest@cox.net. What
More informationFlooring Nails 6-D Flooring Nails $3.40 / 1# 6-D Flooring Nails $14.50 / 5# 8-D Flooring Nails $3.40 / 1# 8-D Flooring Nails $14.
Nails Nails Drywall Screws Common Nails 4D Common Nails $3.85 / 1# 6D Common Nails $3.00 / 1# 6D Common Nails $74.25 / 50# 8D Common Nails $3.00 / 1# 8D Common Nails $74.25 / 50# 10D Common Nails $3.00
More informationVersatrac Bypass Door Units, Conventional and Top Track, 300 and 400 Series
Versatrac Bypass Door Units, Conventional and Top Track, 300 and 400 Series TM Rough opening width (finished opening width plus 9/16") Notch for top track units (used as frame header) Rough opening height
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS HIGH PRESSUE LAMINATE (HPL) TOILET PARTITIONS 1030 TrimLineSeries 1040 DesignerSeries Includes continuous hardware option.65. IMPORTANT: Storage and Handling Information on last
More informationBox Track INSTALLATION INSTRUCTIONS
Box Track INSTALLATION INSTRUCTIONS BOX TRACK Recommended Tools Level Tape Measure Pencil Drill with 1/8, and 1/4, Drill Bits, Phillips Bit and Slotted Bit Socket Wrench with 9/16 Socket 9/16 and 5/8 Wrench
More informationReady To Go SimpleSpec tm. Installation Manual. For more information, please visit 3-form.com or call
Contents Overview ( 1) 3/8" Varia Panel = Cable Tensioner with Cover Plate KIT Stainless Steel: 3-15-1636-K Black Oxide: 3-15-2005-K Cable Tensioner with Cover Plate SS: 3-15-1636 BO: 3-15-2005 + M8 Thread
More informationSalter Industries Spiral Stair
Salter Industries Spiral Stair The Leader in Spiral Staircases Continuous Sleeve Stair Installation Instructions TOOLS NEEDED: 1. Electric drill with hex chuck and Phillips bit 2. Drill bits 1/8", 1/4",
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS SOLID PHENOLIC TOILET PARTITIONS 1080 DuraLine Series 1180 DuraLine Series Class-A Fire Rated IMPORTANT: Review these instructions thoroughly prior to installation. FLOOR ANCHORED
More informationJabiru Installation instructions
Page 1 of 5 s Step Description 1 Mark out centre line of the installation 2 Align centre line of installation with the centre line of the "Front Panel Cut out" template. Align "FLOOR" on template with
More informationINSTALLATION INSTRUCTIONS KK-K9-C12-K CHEVY IMPALA
INSTALLATION INSTRUCTIONS KK-K9-C12-K 2000-2005 CHEVY IMPALA READ ALL INSTRUCTIONS PRIOR TO INSTALLATION TOOLS REQUIRED: Power Drill Drill bits1/4 and 5/32 7/l6 wrench and socket 15,18 and\or 19mm socket
More informationINSTALLATION INSTRUCTIONS
www.marwincompany.com Kit Number Door Height Rough Opening Height KD200BB68 80 84 ½ KD200BB70 84 88 ½ KD200BB80 96 100 ½ INSTALLATION INSTRUCTIONS 200BB SERIES KD POCKET DOOR FRAME FOR 2 X 4 STUD WALLS
More informationJenny Legs Assembly Instructions
Jenny Legs Assembly Instructions R EXTENDED PHILLIPS BIT MM ALLEN WRENCH 6MM HEX DRIVE /" 007 Steelcase Inc. Grand Rapids, MI 90 U.S.A. Printed in U.S.A. Page of 6 88000 Rev F Jenny Club Instructions:
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS SOLID PHENOLIC TOILET PARTITIONS 1080 DuraLineSeries Class-A Fire Rated Includes Institutional Hardware Option.67 IMPORTANT: Storage and Handling Information on last page. Review
More informationPrivacy Wall & Glass Selections Pivot-Hinged Door (For products manufactured after September 14, 2009)
Privacy Wall & Glass Selections Pivot-Hinged Door (For products manufactured after September 14, 2009) 3/16" HEX BIT #2 ACR BIT 3/8" HEX SOCKET Full-Height (No Switch) Transom (No Switch) Full-Height (With
More information#11179 Wellington ARBOR
#11179 Wellington ARBOR Assembly INSTRUCTIONS TOOLS NEEDED Tape Measure Variable Speed Drill with #2 Phillips Bit (recommended) or Phillips Screwdriver Hammer or Mallet ARBOR SIDE PANEL ASSEMBLY (Refer
More informationHeavy-Duty Bypass Track System
Heavy-Duty Bypass Track System Please Note: This track system must be installed with the screws going into a solid surface such as studs or a header. Due to the spacing of the holes on these Brackets,
More informationYardistry. External Display YP *Time required for assembly approximately 1.5-2hrs
Yardistry External Display YP40030 *Time required for assembly approximately 1.5-2hrs Components 4 Packages of Panel Clips (Includes 6 Panel Clips and Hardware) 3 16 1/2 x 16 1/2 Signs (hardware Included)
More informationInstallation Instructions
TS SERIES Traditional Square Accessories Installation Instructions " TOWEL BAR.0 " TOWEL BAR.0.90 DOUBLE ROBE HOOK.0.0 " HANDLE. " HANDLE.0 Thank you for selecting American-Standard...the benchmark To
More informationHow To Measure Your Finished Opening
3000 Series Bifold Doors How To Measure Your Finished Opening MEASURE FROM RIGHT TO LEFT 2 PLACES (WIDTH) MEASURE FROM TOP TO BOTTOM 2 PLACES (HEIGHT) Tools Required for Assembly: Tools Needed: Phillips
More informationInstruction page index: Installation Instructions for Bosca Models BOS-XX-C-XX, & BOS-XX-S-XX. Page 1 of 5
Installation Instructions for Bosca Models BOS-XX-C-XX, & BOS-XX-S-XX Page of 5 BOSCA clip-in mount or BOSCA magnetic BOSCA -in mount Instruction page index: Clip-in installation Screw-in installation
More informationMODULAR BUMPER INSTALLATION MANUAL
MODULAR BUMPER INSTALLATION MANUAL Parts List* 1 Center section 1 Side extension, passenger / right 1 Side extension, driver / left 1 Side cap, passenger / right 1 Side cap, driver / left 1 Brush guard,
More informationAssembly and installation help
Assembly and installation help A supplement to the directions The Purpose of this tutorial is to expand (not replace) upon the directions that come with the system and to help provide shortcuts, the first
More informationSwerve Rack CUSTOM RACKS AVAILABLE
CUSTOM RACKS AVAILABLE Swerve Rack The design of the Swerve mirrors the bike frame, thus providing superior bike support while making it easy to secure both the bike frame and wheel with a standard u-lock.
More informationFire Rating 3 hours- hollow metal doors mounted singly 90 minutes- hollow metal and composite core wood fire doors 20 minutes- wood doors
FM-300 Edge Mount 260 Santa Fe Street, Pomona, CA 91767 800-872-3267 909-632-2300 800-232-6752 fax www.markar.com Heavy-duty 14 Gauge stainless steel US32D Satin Stainless Steel (630) Grade 1 4'0" maximum
More informationNOTE: Landscape Forms is not responsible for site preparation, footings, or electrical wiring.
11/2009 Stop Embedded Mount Bollard HANDLE WITH CARE! Pangard II Polyester Powder coat is a strong, long-lasting finish. Protect this finish from damage during installation. Place unwrapped powder coated
More informationTO O L K IT. Public Bike Repair
TO O L K IT Public Bike Repair The Dero Tool Kit includes all the necessary tools to perform most routine maintenance and adjustments on most bikes. All the tools are securely fastened with stainless steel
More informationTwo Panel Frameless Bypass Door
INSTALLATION INSTRUCTIONS Two Frameless Bypass Door Series 00 Please Record Model Number From Carton Label Here Please read these instructions carefully to familiarize yourself with the required tools,
More informationMounting a BalanceBox 400 to a brick wall
Unpack the BalanceBox 400 and remove the Wall frame cover and its bag of screws. Slide the cover out at the top. NOTE: the cover is NOT included with the BalanceBox 400H LOCK SCREW HOLE MOBILE STAND MOUNTING
More informationTriple Bypass System
Triple Bypass System ASSEMBLY INSTRUCTIONS TRIPLE BYPASS SYSTEM Recommended Tools Drill with 1/4 Drill Bit and Phillips Screw Bit 7/16 Combination Wrench Socket Wrench with 7/16 and 9/16 Socket Level Tape
More informationINSTALLATION MANUAL 32273/1205 C C-403 GB - F - D - NL - ES - I - S - SLO
INSTALLATION MANUAL 32273/1205 C-402 - C-403 GB - F - D - NL - ES - I - S - SLO 1A 1B ENGLISH GENERAL INFORMATION The Cassette toilet is available in 2 types: C-402 Cassette toilet with built-in water
More informationAUTOMATIC OPERATOR ACTUATORS & ACCESSORIES
The actuators and accessories on the following pages are to be used with LCN automatic operators. When using actuators supplied by others, such as card readers, consult the factory. The desired function,
More informationSeries 9000 Panel Door; In-Line, Corner and Permanent Wall Application
Series 9000 Panel Door; In-Line, Corner and Permanent Wall Application 5/32" Drill Bit In-Line Corner Permanent Wall 3/16" Allen Wrench If you have a problem, question, or request, call your local dealer,
More informationBarn Door & Hardware Installation Guide
Barn Door & Hardware Guide INTRODUCTION Thank you for purchasing our hardware. Our barn door and hardware will add a stunning accent to your living environment and maximize its space. This manual covers
More informationNX7 SERIES 5-1/2 HANDRAIL
STORAGE & HANDLING The handrails are shipped unassembled. Upon receipt, immediately check all material for any damage that may have occurred in transit and verify that all of the items and quantities are
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS MAXIMUM PRIVACY HIGH PRESSURE LAMINATE (HPL) TOILET PARTITIONS 2030 TrimLineSeries 2040 DesignerSeries IMPORTANT: Storage and Handling Information on last page. Review these instructions
More informationCAB END BEDTRAX (SIDE VIEW)
Supplied Hardware: (8-14) 1/4-20 Allen head bolts, (12-18) UHMW mount blocks, (4) D-ring tie downs Tools Needed: Allen head wrench GET TO IT. INSTALLATION INSTRUCTIONS STEP 1. INSERT (2) MOUNT BLOCKS INTO
More informationFord F150 Front Bumper
2009-2011 Ford F150 Front Bumper Warning! Read the instructions completely before beginning the installation. Before tightening bolts, drilling or cutting where required, check to make sure that there
More informationParts list continues on Page 2 HOUSE PARTS PACKED IN HOUSE BOX PARTS IN SMALL PLASTIC BAG (HARDWARE) POST PARTS PACKED IN THIS BOX (LARGE PLASTIC BAG)
Form 05-07 Instructions and Parts List MSS- Martin Safety System NOTES: () A complete system is packed in two boxes post box and house box. House box contains hardware for both post and house assembly.
More informationLOCKN LOAD FIRST TIME INSTALLATION
LOCKN LOAD TM TRACK MOUNTING KIT ISUZU MU-X 2013+ LS-M & LS-U MODELS ONLY 3 BAR TRACK HEAVY DUTY ROOF RACK SYSTEM MAX VEHICLE ROOF LOAD RATING: 100KG TOTAL LOAD EQUALS WEIGHT OF ROOF RACKS + ACCESSORIES
More informationHANDRAIL HEIGHT PER LOCAL CODE AUTHORITY. 6 3/8" [161.9mm]
PLEASE READ PLEASE READ THESE INSTRUCTIONS THOROUGHLY PRIOR TO BEGINNING THE INSTALLATION! THIS INSTRUCTION SHEET IS INTENDED TO PROVIDE A SPECIFIC GUIDE TO FOLLOW FOR THE INSTALLATION OF THIS. CONTAINED
More informationOXYGEN INSTALLATION. Revision date
12345 1 Hardware List 12345 Flat head wood screw #9 x 7/8 long with #2 Phillips drive, silver Used to attach surfaces and end panels Hex set screw ½-13 x 2 long with 1/4 hex drive, black Used on Legs Hex
More informationCabinet Storage Products
Assembly Instructions Storage Products (UltraStor, Acoustis, Adjustable Shelf, Cover Panels, Closure Panels) Wood Compartment Doors Full Wood Door Compartment Grille Doors Full Grille Door No Doors Contents
More informationKNOB LATCH. Specifications: Glass-To-Wall Installation CAT NO. LAT001 C.R. LAURENCE CO., INC. PROFESSIONAL QUALITY
Specifications: Material: Solid brass Hole Size Required: 7/8" (22mm) Glass Thickness Range: 3/8" (10mm) to 1/2" (12mm) Includes: Knob, Tapered Strike for wall-to-glass installation and J-Hook for glass-to-glass
More information2300 BI-FOLD INSTALLATION GUIDE
2300 BI-FOLD INSTALLATION GUIDE INSTALLATION INSTRUCTIONS OF MAIN FRAME Header #8 x 2½ zinc coated screws 2 1 2 Jamb Jamb 1 1 3 #8 x 2½ zinc coated screws 4 1 4 3 #8 x 2½ zinc coated screws 5 Threshold
More informationGlideRite Retractable Cover System For Hot Spot Spas (SE & SLX only)
List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.
More informationWalk-in Configurations
Walk-in Configurations Includes Wall-to-Open, Corners, and Corner Rounder Bars INSTALLATION INSTRUCTIONS Tools needed: Tape measure, level, pencil, #2 Phillips head screw driver or power drill with a 6"
More informationDowntown Rack. Custom logo option available
Custom logo option available Downtown Rack The Downtown Rack uses thick, square-tube construction that can t be cut with a pipe cutter. The extended width of the Downtown Rack makes for easy bike parking
More informationAssembly Instructions & General Overview
Assembly Instructions & General Overview 1. General Overview & Assembly Order...Page 3 2. Assembling the Structural Components Page 4-11 3. Power, Data, Power Poles and Cable Floor Boxes.Page 12-17 4.
More informationHOUSE PARTS PACKED IN HOUSE BOX PARTS IN PLASTIC BAG (HARDWARE) PARTS IN SMALL PLASTIC BAG (FLOOR CLIPS) PARTS PACKED IN BUNDLE
Check parts against this list before starting assembly. Refer to illustrations on pages 6 and 7 to view house parts. If any shortages are found, refer to Packing Slip for claim instructions. Item 3 5 6
More informationToday s Service Station
F I X IT Today s Service Station The Fixit includes all the tools necessary to perform basic bike repairs and maintenance, from changing a flat to adjusting brakes and derailleurs. The tools and air pump
More informationAdjustable Countertop Installation
Adjustable Countertop Installation Applies to Models: A1, A2, A3, A4, A5, & A6 Required Tools: Stud Finder, Level 1/4 deep well socket, Screwdrivers, Tape Measure, Drill and Drill Bits Language of origin:
More informationIMPORTANT: Read all sections before you start
1 IMPORTANT: Read all sections before you start For the most up to date information please visit our website @ www.newtechwood.com Prior to installing the railing, please consult local zoning laws in regards
More informationGlideRite Retractable Cover System For HotSpring & Tiger River Spas (except Classic & pre-2000 Landmark Spas)
List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.
More informationSTART HERE BEFORE YOU BEGIN FIG 1 STEP 2
PROFESSIONAL INSTALL RECOMMENDED REAR MODULAR / MULTI LED ROOF MOUNTS PART#: Z350040 / Z350050 REAR ROOF LED LIGHT MOUNTS Parts included (1) - Driver Side Roof Mount Upright (1) - Passenger Side Roof Mount
More informationInstallation Manual for Metal Toilet Partitions Standard Series
For Video instructions http://www.hadrian-inc.com/tech-data/installation/toilet-partitions.aspx P a g e 1 Table of Contents Page General Notes and Tools Required 3 STEP 1: Establish Floor Bracket Locations
More informationHeavy Duty I-Beam Trolley
Heavy Duty I-Beam Trolley ASSEMBLY INSTRUCTIONS I-BEAM TROLLEY Recommended Tools Level Tape Measure Pencil Drill with 1/8, 1/4, and 3/8, Drill Bits and Phillips Bit Socket Wrench with 9/16 Socket I-BEAM
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS LAMINATED P LASTIC TOILET PArTITIONS 1540 ClassicSeries with Options IMPORTANT: Storage and Handling Information on last page. For faster, easier installation, please review these
More informationBIKE FILE (301)
B IK E F I L E High Efficiency The Bike File is our most space efficient u-lock compatible product. Sturdy sliding hangers allow nine bikes to be securely stored in an eight-foot section while allowing
More informationInstallation Manual Flat Track Series
Manual Flat Track Series Contents Safety...1 Parts...2 Hardware.......................................... 2 Tools Required..................................... 4.............................................
More informationTrack Rack. * Track Racks are not lockable
The Track Rack s unique staggered, sliding hook design creates the greatest parking efficiency while still providing easy access to any particular bike. When adding or removing a bike to the rack, simply
More informationInstallation Manual for Metal Toilet Partitions Elite & Elite Plus Series
P a g e 1 Table of Contents Page General Notes and Tools Required 3 STEP 1: Establish Floor Bracket Locations 4 STEP 2: Fasten Floor Brackets 4 & 5 STEP 3: Erect Panels 6 STEP 4: Erect Wall Pilaster 7
More informationMelamine Plastic Laminate. Toilet Partition Installation Manual
Melamine Plastic Laminate Toilet Partition Installation Manual PHONE: FAX: 1-866-317-2786 ATTENTION DO NOT MIX FASTENER PACKS EACH FASTENER PACK HAS THE NECESSARY BOLTS, BARRELS AND SCREWS TO INSTALL THE
More informationWeatherfold 4s 50, 75 & 100
Codes Weatherfold 4s 50, 75 & 100 Brio Australia P: +61 2 87186718 W: brio.com.au E: sales@brio.com.au Brio RMD UK Ltd. P: +44 191 2291224 W: briouk.com E: sales@briouk.com INSTBWS1 REV D - NOV 2011 Brio
More informationStainless Steel Continuous Hinges
TABLE OF CONTENTS A ANSI Standards...2 C Cancellation Notification... 2 Concealed Electric Through-Wire... 4-5 Custom Hole Pattern... 2 Custom Length Hinges... 2 D Dutch Door Hinges... 3 E Electrical Modifications
More informationAUTOMATIC OPERATOR ACTUATORS & ACCESSORIES
AUTOMATIC OPERATOR ACTUATORS & ACCESSORIES 8310 Series 4-1/2 Surface and Flush mounts The actuators and accessories on the following pages are to be used with LCN automatic operators. When using actuators
More information#11179 Wellington ARBOR
#11179 Wellington ARBOR Assembly INSTRUCTIONS TOOLS NEEDED Tape Measure Variable Speed Drill with #2 Phillips Bit (recommended) or Phillips Screwdriver Hammer or Mallet ARBOR SIDE PANEL ASSEMBLY (Refer
More informationIntroduction. Rocky Mountain Westy Swing Away Carrier Kit Installation Instructions
Rocky Mountain Westy Swing Away Carrier Kit Installation Instructions Introduction Thank you for purchasing the Rocky Mountain Westy Swing Away Carrier Kit. We pride ourselves in the products we develop
More informationINSTRUCTIONS TS93 GSR PT RIGHT HAND ACTIVE LEFT HAND INACTIVE RIGHT HAND INACTIVE LEFT HAND ACTIVE
INSTRUCTIONS ATTENTION!!! Before you begin, determine installation type (RIGHT HAND ACTIVE OR INACTIVE). Door coordinator suitable for door from 59 to 98 in width. Inactive door width in the case of unequal
More information2010+ Dodge Ram 2500/3500 Front Bumper Install Instructions
2010+ Dodge Ram 2500/3500 Front Bumper Install Instructions Warning! Read the instructions completely before beginning the installation. Before tightening bolts, drilling or cutting where required, check
More informationNew Product Release: October 2014 Boone Racks
New Product Release: October 2014 Boone Racks Double Fido Fountain Mounting: Surface NOTE: THESE ROUGH-IN DIMENSIONS MAY VARY ½: (13 mm) PLUS OR MINUS NOTE: All dimensions subject to manufacturing variance
More informationINSTALLATION INSTRUCTIONS
PARTS LIST ITEM PART DESCRIPTION QTY 73-A 503F 9MM 50G 5A 50E 505S 50H Connector Bracket Door Stops Support Bar Panel Glass Bracket Wall Mount Bracket Rollers Center Guide Recessed Finger Pull Fixed Panel
More informationM10 x 75mm Sockethead Cap Screws. 5mm Fender Washer (12) Included - (8) Required. #10 x 2.5" PH Wood Screws. (30) Included - (24) Required
Door System Unit - Hardware Tools Included: (2) 2mm Allen Wrenches, (2) 3mm Allen Wrenches, (2) 4mm Allen Wrenches, (2) 6mm Allen Wrenches, and (1) 8mm T-Handle Allen Wrench Tools Required: Phillips Screwdriver,
More informationSteel Solutions USA 602 E. Walnut Street Watseka, IL p: (888) f: (815)
Steel Solutions USA 602 E. Walnut Street Watseka, IL 60970 p: (888) 875-5004 f: (815) 432-3364 sales@steelsolutionsusa.com Published February 2011 2011 Steel Solutions USA. All rights reserved. version
More informationHQ Precision-Glide Track Upgrade 2 Extension Kit for HQ Studio Frame Part# QF09750
HQ Precision-Glide Track Upgrade 2 Extension Kit for HQ Studio Frame Part# QF09750 Important Note: Upgrading the track system on the HQ Studio Frame requires the use of this 2 Extension Kit (Part #QF09750),
More informationNX8 SERIES 6-1/4 HANDRAIL W/ VINYL HANDGRIP
6-1/4 HANDRAIL W/ VINYL HANDGRIP TYPICAL ASSEMBLY 5 2 BUTT JOINT 12 10 9 1 8 11 6 3 7 4 BUTT JOINT COMPONENT LIST 1 LEFT RETURN 7 UPPER IMPACT ABSORBER 2 RIGHT RETURN 8 LOWER IMPACT ABSORBER 3 OUTSIDE
More informationDETAILED ILLUSTRATION
FCF1100 Series (Mounting Knuckle to J-Box JB) - INSTALLATION INSTRUCTIONS electricity has been turned off and electrical 4) Reattach j-box cover, gasket and fixture to the j-box. to read these instructions
More informationInstallation Guide. Bi-fold Doors
Installation Guide Bi-fold Doors Installation Guide Components box 1. 6. 2. 3. 7. 5. 4. 8. Contents 1. Fixing plugs 2. Wedge gasket 3. Bottom trolley 4. Top trolley 5. Magnetic keep (x 2 if door height
More informationSINGLE TRACK BYPASS (patent pending) barn door hardware
SINGLE TRACK BYPASS (patent pending) barn door hardware Installation Manual What is included in your kit: Part number Part name Quantity 1 Inner door hanger 2 2 Outer door hanger 2 3 5/16 x 1.5 lag bolts
More informationHCGG Bulk Density Sensor (BDS) Load Cell Replacement
Required Tools: Loc-Tite 242 Allen wrenches 3/32, 3/16, 9/64, 5/32 3/16 wrench Smaller Philips head screwdriver HCGG Bulk Density Sensor (BDS) Load Cell Replacement 1. Close the GrainGage air cut-off valve.
More informationINSTALLATION INSTRUCTION
INSTALLATION INSTRUCTION Plastic Laminate Series contents page 1030 TrimLineSeries...2-21 1040 DesigerSeries...2-21 Urinal Screens, Benches, Shower Seats...22-31 2030 TrimLineSeries Maximum Privacy...32-47
More informationAssembly and Installation Guide
The Easy Hang Closet Solution SM Install Your elfa In An Instant. Enjoy The Benefits For A Lifetime. Basic Tools For elfa Assembly and Installation Level Hand or Power Drill Drill Bits 1/8", 3/8", 5/16"
More informationSLIDING MECHANISM TROLLEY CATCH TROLLEY ASSEMBLY FLOOR GUIDE
Set A Set B PFD30 SG Fire Door Kit FITTING INSTRUCTIONS For use with 44mm thick doors only For Single and Double doors SUGGESTED TOOLS DRILL G-CLAMP TAPE MEASURE (Image for reference only) HACKSAW POCKET
More informationPOWER PET. Low-E Automatic Patio Pet Door Installation and Operating Instructions
POWER PET Low-E Automatic Patio Pet Door Installation and Operating Instructions Power Pet, Regular Height, Patio Door Assembly Steps Estimated assembly time: Under 1 hour STEP 1: Assemble the tools you
More information400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS
12/11/07 PAGE 1 OF 12 400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS Thank you for purchasing our product! *Please read these instructions
More informationIMPORTANT: installation. FLOOR ANCHORED CEILING HUNG OVERHEAD BRACED FLOOR-TO- CEILING ANCHORED
INSTALLATION INSTRUCTIONS MAXIMUM PRIVACY COMPACT LAMINATE TOILET PARTITIONS 2080 DuraLineSeries 2180 DuraLineSeries Class-A Fire Rated Includes Institutional Hardware Option.67 IMPORTANT: Storage and
More informationCRYSTEEL S. this manual must be included with the vehicle after completing the installation.
Website: www.tbei.com E-mail: sales@tbei.com CRYSTEEL S Grain Tipper mounting and operating instructions this manual must be included with the vehicle after completing the installation. Web Site E-Mail
More informationSpring Loaded All Season Roll-Up Doors
Spring Loaded All Season Roll-Up Doors STAND-OFF MOUNTING METHOD INSTALLATION INSTRUCTIONS READ THIS FIRST Carefully examine the crate(s) for damage before opening. If the carton is damaged, immediately
More informationIN 578. Tools Required. Torque Specification: 10mm Socket 7/16 Socket 1/2 Socket 1/2 Wrench 7/16 Wrench 1/8 Allen Wrench.
Tools Required 2011-C Ford F250/F350 No Drilling into Vehicle is Required 10mm Socket 7/16 Socket 1/2 Socket 1/2 Wrench 7/16 Wrench 1/8 Allen Wrench FL277 x 1 Torque Specification: 1/4 Bolts - 6 Ft Lbs.
More informationInstallation Instructions
Installation Instructions For Models: Model Number / Description File Name 1540 Classic Series P-Lam Toilet Partitions 1540.pdf 1 INSTALLATION INSTRUCTIONS LAMINATED PLASTIC TOILET PARTITIONS 1540 Classic
More informationStainless Steel 95C34 Series
Stainless Steel 95C34 Series Toilet Partition Installation Manual PHONE: FAX: 866-317-2786 ATTENTION DO NOT MIX FASTENER PACKS EACH FASTENER PACK HAS THE NECESSARY BOLTS, BARRELS AND SCREWS TO INSTALL
More informationInstallation Instructions Models: SESD180, DESD180, MESD180 1/4" Semi-Frameless Door and 3/8" In-Line Panel
Models: SESD180, DESD180, MESD180 Scan this Barcode for Parts Bag BP.3143.NLT Thank you for purchasing this outstanding product! This booklet will help you install your units safely and successfully. IMPORTANT:
More informationInstallation Instructions for Vista Air Vertically Folding Walls
Installation Instructions for Vista Air Vertically Folding Walls Use these instructions in conjunction with your shop drawings to see the specifics that are particular to the model you are installing.
More informationCustom Wood Frame Overlay for Glass Doors Installation Instructions
MARVEL CUSTOM WOOD FRAME OVERLAY FOR GLASS DOORS Custom Wood Frame Overlay for Glass Doors Installation Instructions Wine Cellars 6SWC 6SWCE 61WC 61WCM 66SWC (2 required) 66SWCE (2 required) Beverage Centers
More informationHow to Install Custom Real Wood and Faux Wood Blinds
Before you begin your installation: READ ALL INSTALLATION INSTRUCTIONS! Make sure that you have all tools and hardware needed for installation. Check the installation surface (wall, ceiling, or window
More information