Narrow Edge Grain. Wide Edge Grain Staggered. Flat Plank Grain Staggered. End Grain. Grain Orientations
|
|
- Arnold Bradley
- 5 years ago
- Views:
Transcription
1 Grain Orientations Narrow Edge Grain Wide Edge Grain Wide Edge Grain, Staggered Flat Plank Grain, Staggered Flat Plank Grain, Random End Grain Narrow Edge Grain Wide Edge Grain Staggered Flat Plank Grain Staggered *Due to variation in wood characteristics, NO two pieces of wood are exactly the same. Samples & pictures should not be considered as an exact match to your final order. End Grain
2 Narrow/Wide Edge Grain Edge grain (or vertical grain) is produced by quarter-sawing the lumber so that the edges of the growth rings are exposed on the widest faces of the piece. Edge grain boards for butcher blocks are made of strips of wood, and after the piece of lumber has been cut into strips, there is a choice of which grain to put facing upwards. When the edge grain is up it is an Edge grain Butcher block top, and when the Face grain/flat Plank is up it is a Face/Flat Plank grain Butcher Block top. *Due to variation in wood characteristics, NO two pieces of wood are exactly the same. Samples & pictures should not be considered as an exact match to your final order.
3 Narrow Edge Grain Staves are.75 Maximum size that can be glued up at one time is 48 x 144. Tops Larger than that can be made and will made in 2 or more pieces that will be seamlessly joined, by using Biscuits and glue. (Joint charges do apply) *Due to variation in wood characteristics, NO two pieces of wood are exactly the same. Samples & pictures should not be considered as an exact match to your final order.
4 Walnut Wide Edge Staggered Distressed Wide Edge Grain - Stave are between 1 ½ to 1 ¾ Maximum size of Staggered that can be glued up at one time without Joints is 48 x 90 Tops Larger than that can be made and will made in 2 or more pieces that will be seamlessly joined, by using Biscuits and glue. (Joint charges do apply) *Due to variation in wood characteristics, NO two pieces of wood are exactly the same. Samples & pictures should not be considered as an exact match to your final order. Multi - Species Wide Edge Staggered
5 Flat Plank Grain/Face Grain Face grain is when a board has one side that is wider than the other; the wider side (top) is referred to as the face, as opposed to the edge. This also may be referred to as the face that is to be visible in the finished product. *Due to variation in wood characteristics, NO two pieces of wood are exactly the same. Samples & pictures should not be considered as an exact match to your final order.
6 Flat Plank Grain/Face Grain Stave are random 3 to 5 Maximum thickness can be 1 ¾ Maximum size of Staggered that can be glued up at one time without Joints is 48 x 90 Tops Larger than that can be made and will made in 2 or more pieces that will be seamlessly joined, by using Biscuits and glue. (Joint charges do apply) Flat Plank Grain/Face Grain Random Width/Staggered Staves are random 3 to 5 Maximum thickness can be 1 ¾ *Due to variation in wood characteristics, NO two pieces of wood are exactly the same. Samples & pictures should not be considered as an exact match to your final order.
7 End Grain The end grain boards are made by cutting the pieces of lumber into blocks and gluing the blocks together with the end grain up, forming the top surface of the cutting board. This block construction makes the butcher block very strong and durable. During cutting and chopping, the end grain wood fibers absorb the impact of the knife blade so the block is resistant to nicks and gouges. End grain tops are typically used for a cutting surface and finished with a food safe oil. The top will need monthly care, meaning a conditioner needs to be applied at least monthly to keep the top from drying out. *Due to variation in wood characteristics, NO two pieces of wood are exactly the same. Samples & pictures should not be considered as an exact match to your final order.
8 Stave are minimum 1.5 x 1.5 Minimum thickness can be 3 Maximum size of END Grain that can be glued up at one time without Joints is 48 x 48 Tops Larger than that can be made and will made in 2 or more pieces that will be joined, by using Biscuits and glue and will have noticeable seams. (Joint charges do apply) End grain tops are typically finished with a Food Safe Oil and do require monthly some cases weekly maintenance depending on the climate. Uses: End Grain top is normally used as a cutting surface/cutting board. *Due to variation in wood characteristics, NO two pieces of wood are exactly the same. Samples & pictures should not be considered as an exact match to your final order.
2018 guide. Wood Surfaces. ...Where Beauty and Craftsmanship Matter Walnut Wood Top Island Narrow Edge Grain
2018 guide Wood Surfaces...Where Beauty and Craftsmanship Matter Wood Top Island Narrow Edge Grain Acclimated to Quality I n c o r p o r a t e d 4 weeks to Perfection www.fabricatorssupply.net 800.298.0644
More informationInstructables Butcher Block Top
Instructables Butcher Block Top Project Overview: This project requires basic woodworking skills and access to woodworking machines. Woodworking machines have sharp cutting edges and are NOT forgiving.
More informationStand & Bowls. optional. Online Extra
Online Extra optional Stand & Bowls Once you make a bowl using the jig and technique from Woodsmith No. 229, it s only natural to see what else you can do with it. The starting point is to make copies
More informationChess board. The true origins of chess are. from old wood scraps Michael T Collins makes a chessboard and a box to store the pieces
What you will need: Combination plane with 3mm, 6mm and 13mm cutters Rip and cross cut saw Block and jack plane Marking gauge and knife Card scraper optional and try square Chess board from old wood scraps
More informationGrade 11 Woods Lift Lid Coffee Table. Based on Under the big Top from Popular Mechanics Website
Grade 11 Woods Lift Lid Coffee Table Based on Under the big Top from Popular Mechanics Website TABLE TOP 1. Select enough lumber to construct a top that is between 22 ½ and 24 wide after jointing. Ensure
More informationThere are three primary units to this box: two three-sided trays (one made to fit over the other) and one case that wraps around the trays.
Instructions for Basic Drop-Spine Box by Sandra Liddell Reese There are three primary units to this box: two three-sided trays (one made to fit over the other) and one case that wraps around the trays.
More informationA WAVE 3D END GRAIN CUTTING BOARD
A WAVE 3D END GRAIN CUTTING BOARD mtmwood 2014 A «Wave» pattern is based on old well- known optical illusion. I used hard maple, movingui and padauk for main part of the board and sapele for the frame.
More informationMade by hands. Flooring Selections
Made by hands. Flooring Selections Wood Grades Wood Species SELECT GRADE (WHITE OAK) KNOTTY GRADE (WHITE OAK) Some wood species can be designated by grade, such as knotty (sometimes called character or
More informationInstructions for Turning Laminated Bracelets
Instructions for Turning Laminated Bracelets 1. Start with Design 1. Make a paper template circle for the bracelet. Use this to check the fit on the person you are making the bracelet for. After checking
More informationTurning a Fast Joint dovetailed vase on a lathe
Turning a Fast Joint dovetailed vase on a lathe Contributed by customer Brian H from Knoxville TN The MLCS Fast Joint precision joinery system offers a broad range of dovetail patterns that can be created
More informationTongue & Groove Cabinet Doors Copyright 2014 JaysCustomCreations.com
Tongue & Groove Cabinet Doors Copyright 2014 JaysCustomCreations.com A tongue and groove cabinet door is made up of at least 5 pieces. Two horizontal rails (blue), two vertical styles (green), and one
More informationFor ANGLE-DROP Styles
For ANGLE-DROP Styles BEFORE INSTALLATION: 1. READ THESE DETAILED INSTALLATION INSTRUCTIONS. 2. Material and tool requirements: - Estimate square footage and add 10%. - Select underlayment (over concrete
More informationGENERAL NOTES: Page 1 of 9
Laminating A Zia Into A Turning Blank by W. H. Kloepping, Jan. 2009 This describes how a zia (the New Mexico state symbol) can be laminated into a turning blank. Materials needed: Square Turning Block
More informationClassic Kitchen Island
America s leading woodworking authority Step by Step construction instruction. A complete bill of materials. Classic Kitchen Island Exploded view and elevation drawings. How-to photos with instructive
More informationA Shaker Sewing Stand
America s leading woodworking authority Step by Step construction instruction. A Shaker Sewing Stand A complete bill of materials. Exploded view and elevation drawings. How-to photos with instructive captions.
More informationPerhaps the best thing about. Three bowls slightly rearranged Twisted Possibilities
Three bowls slightly rearranged Twisted Possibilities By Malcolm Tibbetts Lacewood Ribbon, 13 7½" Perhaps the best thing about segmented turning is the total lack of restrictions; there is no end to the
More informationLAMINATE FLOORING INSTALLATION INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION.
READ ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION. If your starting wall is uneven, refer to Fig 11 to prevent having to uninstall rows. Taking measurements to ensure you will not have too small a final
More informationOdd Wobbler Instructions By: Don Geiger
Odd Wobbler Instructions By: Don Geiger Stock Size Calculations and Reference Table When preparing stock material for turning an Odd Wobbler, you will need two pieces of dry wood that is about one inch
More informationTURNED BIRD HOUSES Shelter from half-inch-thick stock
TURNED BIRD HOUSES Shelter from half-inch-thick stock SUSAN SCHAUER LOCALS CALL ME THE BIRDHOUSE Lady. I take it as a compliment. My turning career began making lathe-turned birdhouses, and I continue
More informationTapersawn Shake Installation Instructions
Smart-Shingle TM System Tapersawn Shake Installation Instructions INSTALLATION GUIDE MARKS Shake-Strip 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
More informationGleanings from Townsend Dovetail Joinery
Gleanings from Townsend Dovetail Joinery Jeffrey Greene 2014 The dovetailing of drawers and cases, the most fundamental and essential joint in the cabinetmaker s repertoire, has long been a subject of
More informationTraditional glass-pane and wood-muntin doors highlight this free-standing piece.
Bookcase Traditional glass-pane and wood-muntin doors highlight this free-standing piece. As the saying goes, there's nothing like good books. But they can present some storage problems--especially if
More informationChristmas Bell Ornament
Christmas Bell Ornament This is an easy Christmas ornament idea I cabbaged from a friend and skilled turner, Curt Fuller, from Utah. I kind of adapted it to my style but I still got the idea from him.
More informationStep-by-Step Instructions for Making the Wall-hung Bookcase
Step-by-Step Instructions for Making the Wall-hung Bookcase When a piece of furniture has an air and look of simplicity, you can be sure that it deftly conceals the complexity of its making. I wanted this
More informationCrafting a Dizzy Bowl
Crafting a Dizzy Bowl Visit Youtube.com Visit Youtube.com In the search section type dizzy bowl and you will find dozens of videos about turning dizzy bowls. Visit Youtube.com In the search section type
More informationInstall Windsor Corners
Install Windsor Corners Tools and Supplies You'll Need 1. Exterior Grade Screws use screws that are long enough to go through the FauxPanel and firmly attach to the wall behind the FauxPanel. We recommend
More informationYou expect to find PVC. PVC Lumber PROS & CONS OF PVC PROS
PROS & CONS OF PVC PROS Won t rot. Doesn t have to be painted (but can be). No defects; consistent. Easy to cut and machine. Readily available. CONS Not designed for structural use. Plastic appearance
More informationREINFORCING THE CORNERS OF FLAT FRAMES
REINFORCING THE CORNERS OF FLAT FRAMES There are a number of different methods that may be used to join flat frame sides together. As most Woodworkers know, end grain glue joints are not nearly as strong
More information(1) C & C 30 MK I I. Building the Wine Glass Holder
(1) C & C 30 MK I I Building the Wine Glass Holder 1. This package contains instructions and sketches plus scanned pictures. 2. Woodworking skills and equipment are essential to make the pieces and assemble
More informationDining Table with Two-Way Drawers
Dining Table with Two-Way Drawers DOUBLE-FRONTED DRAWERS MAKE THIS PIECE UNIQUE With two drawer fronts, a center beam, plywood bottoms, and custom pulls, these drawers are both distinctive and durable.
More informationSilverware Chest Plan
Silverware Chest Plan 05L14.01 Introduction 1. Measure the space required for your cutlery before beginning this project to be sure that it will fit in the drawers and top compartment. The best way to
More informationEngineered floors in Junckers quality
Engineered floors in Junckers quality Oak Sonate Plank Walnut Sonate 3 strip 2 A wooden floor the first furniture in the room! Ash Whitesand Sonate 1 strip Ash Sonate 1 strip Interior design is easy with
More informationScratchbuilding with 3D Building Materials Cut Lintels, Install Corners
The most realistic brick on the market today, these 3D engraved sheets are from actual photos of brick walls. We engrave every detail into basswood with a laser. Why put brick on wood? For modelers who
More informationHANDCRAFTED LIDDED CHEST IN CHERRY With Red Cedar Lining
HANDCRAFTED LIDDED CHEST IN CHERRY With Red Cedar Lining Design A chest was desired as a gift to family. The Shaker style of furniture was identified as a pleasing style. After viewing a number of pictures
More informationBuilding Bigger Things
Learning More About Wood Itself Now that you know a little about how the wood was manufactured for your woodworking projects, you may want to learn more about the wood itself the structures and properties
More informationBUILDING A STORM DOOR
BUILDING A STORM DOOR BY NEAL BARRETT Illustrations by George Retseck If you're in the market for a storm door, you probably know that there are many styles and models available. However, most of them
More informationHills for Wargames By Matakishi
Hills for Wargames By Matakishi I make my hills from 9mm thick cork tiles which are 30cm (1ft) square. I glue two together to make an 18mm high section and finally, after I've cut them to the required
More informationHow to Edge Joint Boards
How to Edge Joint Boards It s unusual to find solid boards much over 300mm wide, and anything over about 150mkm is likely to be unstable. So for wide solid pieces it is necessary to edge joint boards together
More informationBUILD THE. Soleil Royal. Pack 1. The flagship of King Louis XIV.
BUILD THE Soleil Royal The flagship of King Louis XIV www.model-space.com Pack 1 Stage 1 Assembly Guide Hull frame, false keel and first deck half A 4 2 5 1 6 7 1A Smooth the surfaces of all the pieces
More information3D END GRAIN CUTTING BOARD N3
3D END GRAIN CUTTING BOARD N3 mtmwood 2014 This pattern shows a 3D optical illusion of the zigzag wall lit by the sun. I used hard maple, black walnut and black cherry for this project. You may use other
More informationBlock Lesson #11. Lesson Supplies UPDATED. Preparing the binding strips. Skill Builder BOM BLOCK LESSON #11 NOVEMBER 20, 2013
UPDATED 1 BLOCK LESSON #11 NOVEMBER 20, 2013 Block Lesson #11 Skill Builder BOM In this lesson you will learn how to join your finished quilted and trimmed quilt blocks together with binding joints to
More informationNojo Design: Large Step Cabinet: February 2012
Nojo Design: Large Step Cabinet: February 2012 The largest single piece of furniture I ve ever made is this stepped cabinet. Finished piece is 8! tall and over 10 long. This project has been great, although
More informationPinewood Derby Display Case
Pinewood Derby Display Case Optional Door Design by Neil Fern - Pack 187 Exterior Dimensions 23 ½ (H) X 10 ½ (W) X 3 ½ (D) Front Back OPTIONAL Door Finished Interior Dimensions 21 7/8 (H) X 9 (W) X 3 (D)
More informationSlanted Brick Pattern Pen Blanks
Slanted Brick Pattern Pen Blanks Contributed by: Joseph Schneider & Kevin Kronewitter A.K.A wood128 & kronewi This tutorial was downloaded from http://www.penturners.org The International Association of
More informationALAN CARTER STUDIO 5332 RIVERVIEW DR., LISLE, IL
ALAN CARTER STUDIO 5332 RIVERVIEW DR., LISLE, IL 60532 630-971-0690 apcarter@sbcglobal.net www.alancarterstudio.com SPLITTING THE DIFFERENCE This is for all you slackers out there. Sometimes half measures
More informationDovetail Saw Guides. Figure 1: Dovetail saw guide, exploded view. Guide Block. UHMW Friction Pad. Sliding Clamp. Rare-Earth Magnet
Dovetail Saw Guides U.S. Pat. No. 6,607,016 Dovetail joints have traditionally been the hallmark of a cabinetmaker who had acquired an expert level of skill. They are also a mark of quality and attention
More informationPlease contact us at to discuss your project.
Since 1999, Trillium Cabinet Company has been designing and building premium, handmade cabinetry and fine furniture for residential, commercial, and professional customers across the nation. We offer complete
More informationRoof Contour By Bob Parrish
Roof Contour By Bob Parrish This text will show you how to shape the roof contour on Labelle passenger and trolley kits. The height of the clerestory on the two types of kits is different. Passenger kits
More informationCopyright WilkerDos.com Dining Table. Project Designed By April Wilkerson - Plan Created By Jay Bates (jayscustomcreations.
Copyright WilkerDos.com 2017 Project Designed By April Wilkerson - Plan Created By Jay Bates (jayscustomcreations.com) Layout & Shopping List Page 2 of 12 Layout & Shopping List Item Quantity Description
More informationHand Dovetails. They're really not that hard to do. by Alphonse Mattia
Hand Dovetails They're really not that hard to do by Alphonse Mattia Dovetailing is one of the strongest and most attractive methods of joining the ends of boards together. Traditionally, handcut dovetails
More informationHOW I BUILD A DOOR Ed Hollingsworth Omaha, Nebraska
HOW I BUILD A DOOR Ed Hollingsworth Omaha, Nebraska Some years ago, my wife and I bought a small wooded acreage in the bluffs above the Missouri River valley north of Omaha, Nebraska. My plan was to make
More informationTimberflex & Flexboard Technical Guide
Timberflex & Flexboard Technical Guide A bendable substrate material that can be formed first and laminated last Patent #5,618,601; #5,232,762; #5,824,382 Doors Larger radius and small doors are easily
More informationGONDOLA LUMBER LOAD. A cheap load from scraps for an Athearn 50 gon.
GONDOLA LUMBER LOAD A cheap load from scraps for an Athearn 50 gon. What do you do when you have a project and there s a lot of wood off-cuts left over? The answer is simple: you take the off-cuts and
More informationSize Specifications. Specifications. Bow, Warp and Twist Tolerances
Size A minimum size dimension is listed for each door and drawer front. When ordering, one of the minimums must be exceeded by at least ". For example, if a door minimum is listed at 10" x 10", the door
More informationAhead of the curve 2 Part
F&C PROJECT Ahead of the curve 2 Part In the second part of this series, Chris Tribe constructs the table for his stylised cabinet which we looked at last month in F&C Accuracy in turning the legs for
More informationThank you for purchasing E.L. Moore Window & Door.
Thank you for purchasing E.L. Moore Window & Door. Instructions Version 4.28.15 I ve named this kit after one of the greatest modelers I ve ever known, the late Elliot Moore Jr. Rest in peace my friend.
More informationAmerica s leading woodworking authority To download these plans, you will need Adobe Reader installed on your computer. If you want to get a free copy, visit: http://adobe.com/ reader. Having trouble downloading
More informationKitchen Step Stool. Premium Plan. In this plan you ll find: America s leading woodworking authority
America s leading woodworking authority Premium Plan In this plan you ll find: Step-by-step construction instruction. A complete bill of materials. Construction drawings and related photos. Tips to help
More informationFLOORING LUMBER LO GS TABLE TOPS 39 SPECIES 40 GRADES 41 PATTERNS 42 LENGTHS & THICKNESS 44 ASSOCIATIONS 47 LOG BUYING
www.grafbro.com FLOORING HICKORY CHARACTER P/S 5 WHITE OAK SELECT QTD. 7 WALNUT SELECT R/Q 9 WHITE OAK CHARACTER CHARACTER & BETTER 11 WALNUT CHARACTER P/S 13 HICKORY CHARACTER P/S 15 WALNUT SELECT R/Q
More informationClose Encounters of the Bird Kind
Close Encounters of the Bird Kind Building some bird housing will improve your libido as the natural forces of Spring work their magic. Materials: ¾", 2" and 3" exterior screws 1" x 8" pine or spruce 1"
More informationStair Tread & Riser Installation Guide
Stair Tread & Riser Installation Guide 1 P age Wood A Natural Product We, at Artistic Finishes, accept and appreciate the natural beauty that comes from real wood. Because no two trees produce the same
More informationInstallation Instructions
www.marlite.com Effective Date 03/01/2018 ARTIZAN FRP, SYMMETRIX FRP, ENVUE FRP, STANDARD FRP Installation Instructions Statements expressed in this technical bulletin are recommendations for the application
More informationWorking with Wood & Tools. Marking and Measuring. Tools you will need:
Marking and Measuring English Measure If you want to make pieces of a certain size, you will have to measure and mark them before you do any cutting. Examine a rule and find an inch mark. The mark (")
More informationMarquetry Straw Valentines Card
Marquetry Straw Valentines Card Sweet 'n Simple - a special card for that special person. You will need: Tools Ruler Pencil Scissors If you use straw that needs splitting: a seam ripper or a Hindenburg.
More informationExterra Installation Guide
Exterra Installation Guide Installing the foam padding Please review this installation guide before you begin installing the floor. If you have any questions, please call us at 800-428-5306 any time Monday
More informationCOMPLIMENTARY WOODWORKING PLAN
COMPLIMENTARY WOODWORKING PLAN COFFEE TABLE PLAN This downloadable plan is copyrighted. Please do not share or redistribute this plan in any way. It has been paid for on your behalf by JET Tools, a division
More informationA Magazine Rack with a Top
A Magazine Rack with a Top Introduction: I have never come across a good free plan for a magazine rack. Yet almost all homes have one. So this is one of the few items I have made on my own, as I don t
More informationTool Box. Process Guide
Tool Box Process Guide Design, Lumber, & Nails Needed Designed from typical big box lumber dimensional lumber to minimize the rip cuts Added feet to allow the box to sit on uneven surfaces Add a sliding
More informationInstallation Instructions for Siding
Smart-Shingle TM System "The new smart way to install cedar shingles." - This Old House Installation Instructions for Siding V3.2 INSTALLATION GUIDE MARKS Shingle-Strip 0 1 2 3 4 5 6 7 8 9 10 11 12 13
More informationWEST ISLAND WOODTURNERS
WEST ISLAND WOODTURNERS March 25th 2014 DEMO Laminated Salt & Pepper Shakers 4130 Papineau Trois-Rivières, Qc G8Y 1P5 819 374-1404 www.davepott.com Cut blank on saw set at 2.1 wide X 2.1 high X 5.1
More informationtwiddletails Strippy Runner Tutorial Makes a runner approximately 17½ x 50
1 twiddletails Strippy Runner Tutorial Makes a runner approximately 17½ x 50 Fabric Requirements: 4 coordinating fabrics, 11 x 18 (half a fat quarter/ a fat eight) each 18 x 22 (a fat quarter) solid fabric
More informationHow to Construct the 8-Point Star by Jay S. Helland
How to Construct the 8-Point Star by Jay S. Helland 1-5-2013 The photos in these instructions were not taken in consequential order but provide the reader the general idea of the processed used. The process
More informationHow to Build a Recessed Medicine Cabinet
How to Build a Recessed Medicine Cabinet See post for install info http://www.hertoolbelt.com/recessed-medicine-cabinet/ Materials 6 Inset Cabinet Door Hinges 3 Latches 1 sheet Beadboard or 1/4 plywood
More informationAPPLICATION INSTRUCTIONS FOR DINGEWOOD SIDING
APPLICATION INSTRUCTIONS FOR DINGEWOOD SIDING SQUARE FOOTAGE Customers should plan on ordering 10-20% more wood because wood is, by nature, imperfect. Prefinished wood will come pre-stained, but wood planks
More informationSTAIR TREAD & RISER INSTALLATION GUIDELINES
STAIR TREAD & RISER INSTALLATION GUIDELINES ARTISTIC FINISHES DOES NOT WARRANTY THE COMPLETENESS OR ACCURACY OF ANY INSTALLATION. THE INSTALLATION CONTRACTER MUST HAVE THE EXPERIENCE AND KNOWLEDGE TO COMPLETE
More informationc o n s u m e r guide - a homeowner s buying guide European Solid Wood Work Tops perfect for today s kitchens
c o n s u m e r guide - a homeowner s buying guide European Solid Wood Work Tops perfect for today s kitchens What are Café Countertops? THE ONLY WOOD COUNTERTOP MADE IN AMERICA WHICH IS BOTH FOOD-PREP-SAFE
More informationCROTCH-GRAINED CHESS TABLE. Walnut, Poplar
3 CROTCH-GRAINED CHESS TABLE Walnut, Poplar 11 MAKING THE CHESS TABLE This piece is designed around a set of angles taken from the playing pieces, angles echoed in the fat dovetails holding the stretchers
More informationPROJECT PLAN MODERN COFFEE TABLE
BUILD IT WITH ROCKLER PROJECT PLAN MODERN COFFEE TABLE With its clean lines and striking geometry, this coffee table will lend iconic midcentury modern style to any living space. And you can build it yourself
More informationVisualization & construction of simple rotors for micro wind turbines
Visualization & construction of simple rotors for micro wind turbines John, Jafar & friends - 2002-2003 BLADE CARVING Friends: It has been our objective to conduct research into "construction and
More informationLUXURY VINYL FLOORING INSTALL INSTRUCTIONS
PLEASE READ ALL INSTRUCTIONS CAREFULLY BEFORE YOU BEGIN INSTALLATION. IMPROPER INSTALLATION WILL VOID WARRANTY. Installation Preparation: The information on this sheet provides general guidelines. All
More informationTurada Hardwood Shingles and Shakes Installation instructions
1. General 1.1 Maximum Exposure: Maximum exposure for wood shingles and shakes shall comply with Table 1 herein, unless specifically specified in the roof assemblies Product Approval. 1.2 Solid and Spaced
More informationDemilune 4. Apron Joinery. Curved Apron Tenon. Bridle Joint Legs. Bridle Joint Front Apron
Demilune Email 4 Apron Joinery There are two types of joints used in connecting the aprons and legs. The rear legs use conventional mortise and tenon joints, while the front legs use the less conventional
More information136 PLYWOOD DESK 522
136 PLYWOOD DESK 522 Simple in design and inexpensive, this plywood desk is made from a single 4- x 8-foot panel. Plywood is available with many hardwood veneers; it can also be covered with plastic laminate,
More informationWhat materials are available?
Traditional materials: Timber, stone and Brick What materials are available? Technological advancements have introduced a larger selection of materials such as: Concrete blocks Structurally engineered
More informationRose Inspired Corner Shelf
Photo 1: The side pieces are sized so you can hot melt glue them together outside of the pattern. Scoring a shallow v-groove with a utility knife holds the glue at bay. Rose Inspired Corner Shelf The best
More informationOriginal Recipe. Original Recipe can be found at
Original Recipe Hi everyone! It s Andrea from Urban Quiltworks. I have always admired the look of bargello and watercolour style quilts. When I saw the range of colours and values in this Zen Chic Figures
More informationPreparation of Wood: From Rough to Smooth, Straight and Square. Paul Roberts
Preparation of Wood: From Rough to Smooth, Straight and Square Paul Roberts Accurate machining fundamental to quality of woodworking Rough timber-defects flat, square & straight Rough timber cut/planed
More informationWe can source any type of flooring to order including exotic timbers and different hand finishes
PRODUCT GUIDE for BAMBOO SOLID & ENGINEERED FLOORS Sol We manufacture all our own wooden flooring and you cannot buy it from anyone else, please see our full range of flooring including Oak, Maple, Walnut
More informationMake your own Blacksmithing Bellow By Bobby Floyd (Jan. 2014)
1 Make your own Blacksmithing Bellow By Bobby Floyd (Jan. 2014) Some before rehabilitation photos of this small blacksmithing bellow ca. 1900 (Length 45, Width 25 ½, Weight 33 lbs.). More before photos
More informationProject Plans Kreg Tool Company/BuildSomething. All Rights Reserved.
BY Project Plans ONE-OF-A-KIND CUTTING BOARD This solid-maple cutting board offers ample space for cutting and a comfortable handle, but the most-unique feature lies underneath. A cutout in the lower layer
More informationENJOY THIS SELECTION FROM. Pocket Hole Joinery. Pocket Hole. Joinery Bookshelf Day bed Mirror/picture frame Dresser Bathroom vanity...and More!
t ENJOY THIS SELECTION FROM Pocket Hole Joinery Pocket Hole Joinery Bookshelf Day bed Mirror/picture frame Dresser Bathroom vanity...and More! Mark EdMundson To purchase your copy of Pocket Hole Joinery,
More informationIndian Blanket Blanks
Indian Blanket Blanks Contributed by: Jeff Powell A.K.A workingforwood This tutorial was downloaded from http://www.penturners.org The International Association of Penturners - 2014 Indian Blanket Blanks
More informationHalf-Blind Isoloc Joint Procedures
ISOLOC - CHAPTER 6 Half-Blind Isoloc Joint Procedures 6- Always use scrap boards to practice and test for fit. Rip the boards to width to suit the chosen template. The pin boards should not be less than
More informationTechnical Tips. Using Bundle Breaker (rotary corrugated applications) In General, bundle breaker rule is determined based on the following criteria:
Technical Tips 080215_BBarticle Using Bundle Breaker (rotary corrugated applications) Bundle Breaker: a mechanical device designed specifically to separate ganged, multiout sheets after they have been
More informationLeverage FSG. Imagine your office made to order match, replicate, build
Leverage FSG Imagine your office made to order match, replicate, build Your Office Made To Order! Leverage FSG Executive office suites traditional, transitional and contemporary styles that you choose
More informationStunning. Sustainable. Superior. Introducing
A Modern Classic Introducing Stunning. You ve Never Seen Hardwood Like This. Long wide planks. With 100% hardwood core for stability and long-lasting performance, finished beautifully with Best-in-Class
More informationDIY CHILD S STOOL. Instructions
DIY CHILD S STOOL Children have their own special world. And having the right furniture is part of that world. We have designed an easy-to-assemble child's stool that you can paint in a selection of bright
More informationHow to install Magic Metal
How to install Magic Metal First you need the following tools: Glue: Indoor Out Door Carpet Glue 3 gallon pail. A few rollers (the thinner nap the better) a pan with liner. A good utility knife with extra
More informationColonial Washstand Circa 1760
Colonial Washstand Circa 1760 I found the original of this piece while on vacation on Jekyll Island in Georgia. It was one of a pair in a conference room at the Jekyll Island Club Hotel, part of the island's
More informationHandmade Hard-Bound Scrapbook Cover
Handmade Hard-Bound Scrapbook Cover Equipment Guilotine paper cutter Mod Podge roller applicator Mod Podge roller Paper folding knife The Cinch binding machine Scissors Iron Wire cutters Materials 15 inch
More information