Copyright WilkerDos.com Dining Table. Project Designed By April Wilkerson - Plan Created By Jay Bates (jayscustomcreations.
|
|
- Melvin Malone
- 5 years ago
- Views:
Transcription
1 Copyright WilkerDos.com 2017 Project Designed By April Wilkerson - Plan Created By Jay Bates (jayscustomcreations.com)
2 Layout & Shopping List Page 2 of 12
3 Layout & Shopping List Item Quantity Description 2x8x10' 2 Pine or similar. For the top. You can substitute hardwood for this. 2x8x8' 2 Pine or similar. For the top. You can substitute hardwood for this. 2x4x10' 6 Pine or similar. For the base. 2x4x8' 2 Pine or similar. For the base. 2x6x8' 1 Pine or similar. For the base stretcher. 3/8"x36" dowel Aprox. 1 Hardwood dowel like oak or maple. Pine or poplar will crush when driving them home. Give or take a few inches depending on how long you cut each dowel. 2 1/2" wood screws 16 To secure the curved base pieces. Wood glue Sticky. Finish of choice leveling feet 4 Optional. Page 3 of 12
4 Reference Diagrams BOTTOM VIEW FRONT VIEW SIDE VIEW STRETCHER TOP VIEW STRETCHER FRONT VIEW SMALL FLAT SPOT BEFORE LARGE RADIUS ON BOTH SIDES, TOP AND BOTTOM. Page 4 of 12
5 x2 = x1 = x4 = Step 1 Glue the oversized blanks. You can save time by gluing two "glue-ups" together. Notice on the top two diagrams the boards are shifted in the clamps. This represents the outside pairs being glued together but no glue in the middle. This way you can glue multiple assemblies with the same amount of clamps. Page 5 of 12
6 Step 2 This diagram shows both leg posts, 90 degrees from one another. Cut the center post to size. The post is 3" x 3 1/8" x 33". Cut the female end of the bridle joint on all four ends. Each bridle joint cut is 1" wide, 3" deep, and is centered along the 3 1/8" width direction. Cut the 1" wide and 3" tall through mortise on the face opposite of the bridle joints 7" up from the bottom. Step 3 This diagram shows the top and front view of the top and bottom post pieces. Cut top and bottom pieces for each post. The bridle joint is centered on each piece. Cut it first Remember that it's better to sneak up on the fit rather than cut too much away at first. Use whatever circle object you have handy to trace an appropriate size arc for the curved ends. Page 6 of 12
7 Step 4 Verify the top and bottom pieces fit for each post. Do not glue them at this point. With the top and bottom fitting appropriately trim the blanks for the curved pieces to the exact length to fit between the top and bottom. Then plane them to the same thickness or width as the top and bottom pieces. Then find the vertical center between the post and each blank and drill a 3/8" hole that is 1" deep for a single dowel to connect them later. Step 5 Feel free to make this any shape you want. I chose to make an arc that has a constant width of 2 1/2". This diagram represents a final length of 27" for the curved piece. This length should be the same as the distance between the bridle joints on your post pieces. Adjust according to your exact pieces. Page 7 of 12
8 Step 6 Complete a dry assembly of each side. Use a 1 3/4" long piece of 3/8" dowel between each curved piece and the center post in the previously drilled holes. With everything aligning as it should drill two 1/2" wide holes through the top of the top piece and through the bottom of the bottom piece about halfway through towards the curved piece. Then secure the curved piece in place with a 2 1/2" screw through each of these holes. Once everything is fitting and secured like it should be disassemble and then reassemble the entire piece with glue in each of the joints. Step 7 Cut the lower stretcher according to the reference diagram. The tenon should fit snug into the through mortise on the post and the wedge mortise should be inset 1/8" into the post. Step 8 Use scrap wood from the base or a matching wood from the top to cut make two oversized wedges. An approximate size is shown on this diagram. Page 8 of 12
9 Step 9 Insert the wedges from each side and gently drive them tight with a mallet. This will pin the stretcher in place and hold it snug against the leg assemblies. This also allows the entire table base to be disassembled when you need to move the table to another location. Step 10 Glue the top panels together. Cut the completed panel to the final size shown here making sure each end grain end is perfectly flush. Step 11 The following diagram shows the front, side, and top view of the breadboard end piece. First, drill three 3/8" through holes 1" in from the edge as indicated by the dimensions. Reference from the center point and not the ends. Then use a router with an edge guide to create a 1/2" wide x 1-1/2" deep groove through the entire length on the side that has the holes. Try to set the edge guide so the router is as centered as possible. Regardless of how close you got, make a pass referencing off of each side for every pass you make. This will ensure a perfectly centered groove. It's OK if the groove is slightly more than 1/2" wide. Page 9 of 12
10 Step 12 The following diagram represents the front, top, and side view of the top panel. Use a router and an edge guide to cut a matching tongue on each end of the top panel. Make sure you remove an even amount of material from the top and bottom so that the tongue is centered along the thickness direction. This will require flipping the top a few times so be careful. Again, sneak up on a perfect fit before cutting the entire joint. Adjust the router depth to make an oversized tenon after one pass on the top and bottom. Test your fit. Adjust the router bit depth a tiny bit and repeat the process until your piece fits perfectly. Then complete the rest of the joint with the established router depth. Page 10 of 12
11 Step 13 With the tongue and groove joint fitting nice and snug place the breadboard ends on the ends of the panel. Use a 3/8" brad point drill bit and a mallet to mark the center location of the holes onto the panel tongue. Remove the breadboard ends and drill the holes and slots for the dowels 1/16" closer to the center of the panel for each of the previously marked holes. The 1/16" offset will pull the joint tight when the dowels are driven through. The end holes need to be slots to allow for expansion and contraction. 3/8" HOLE 1/16" CLOSER THAN REFERENCE MARK Page 11 of 12
12 Step 14 Time to install the breadboard ends. Cut six pieces of dowel that are about 1" longer than the thickness of the top. Use a knife to slightly taper about 1/2" of one end of each piece of dowel. Place glue on the center 6" of each side of each tongue on the large panel. Add the breadboard end making sure the center holes align. Drive the center dowel through the hole from the top side of the table top. Because the holes in the tongue part of the joint are slightly offset to the middle of the table the breadboard end will be pinned tightly against the glued panel. The taper cut on the dowels will allow the dowel to access the bottom hole in the breadboard end. Once the dowel is driven through the other end and still about 1/2" proud of the surface apply glue to the sides of the dowel and then drive it down leaving it slightly proud of the surface. Repeat this step for each of the other dowel holes. It's important that the glue surface only touches the top part of the breadboard end and isn't glued to the tongue part of the joint. Step 15 Use a flush trim saw or a sander to flush the dowels with the table top on both sides. Trim the breadboard ends flush with the center panel. Use a biscuit jointer or something similar to cut slots into the top inside edges to use table top hold down clips. With the table top upside down on the floor or a work surface attach it to the base with table to hold down clips. See my build video for reference if you have never used them before. Disassemble, sand, and finish as you wish. Page 12 of 12
World. Old. Dining Table YOU CAN BUILD AN
YOU CAN BUILD AN Old World Dining Table This design combines heavy oak timbers with period specific elements. The result brings an old world look to a modern sized dining table. Publisher: Jeff Branch
More informationWorld. Old. Dining Table YOU CAN BUILD AN
YOU CAN BUILD AN Old World Dining Table This design combines heavy oak timbers with period specific elements. The result brings an old world look to a modern sized dining table. Publisher: Jeff Branch
More informationTrestle Table and Benches Materials List
Project 18444EZ: Trestle Table and Benches In the early days of our country, trestle tables were popular because they could easily be disassembled and moved out of the way when not in use no small advantage
More informationDisplay Case (for J&S)
Display Case (for J&S) This is constructed of maple plywood with solid maple (soft maple) edge banding. It was made to fit between a door and a kitchen cabinet, and has an elegant circular taper between
More informationThe WoodWorker s Edge
The WoodWorker s Edge Draw-leaf Game Table 1. 2. Layout the area for the tenons. The tenons are 3/8 thick x 4-1/2 long x 1-1/4 deep and offset to the inside. Create the tenons using the step method to
More informationCOMPLIMENTARY WOODWORKING PLAN
COMPLIMENTARY WOODWORKING PLAN COFFEE TABLE PLAN This downloadable plan is copyrighted. Please do not share or redistribute this plan in any way. It has been paid for on your behalf by JET Tools, a division
More informationBUILDING A STORM DOOR
BUILDING A STORM DOOR BY NEAL BARRETT Illustrations by George Retseck If you're in the market for a storm door, you probably know that there are many styles and models available. However, most of them
More informationWorkbench. Process Guide
Workbench Process Guide Design, Lumber, Tools & Nails Made entirely from 2x and 4x construction lumber Hardware speeds up the consturction while also reduces the amount of planing we have to do by using
More informationTongue & Groove Cabinet Doors Copyright 2014 JaysCustomCreations.com
Tongue & Groove Cabinet Doors Copyright 2014 JaysCustomCreations.com A tongue and groove cabinet door is made up of at least 5 pieces. Two horizontal rails (blue), two vertical styles (green), and one
More informationHANDCRAFTED LIDDED CHEST IN CHERRY With Red Cedar Lining
HANDCRAFTED LIDDED CHEST IN CHERRY With Red Cedar Lining Design A chest was desired as a gift to family. The Shaker style of furniture was identified as a pleasing style. After viewing a number of pictures
More informationMODERN BED FRAME ROCKLER BUILD IT WITH BUILD SIMPLIFY CUSTOMIZE. Plan Value $14.99
BUILD Stock # Item 63446 Baltic Birch Plywood /2" x 24" x 30" (2 qty) Stick veneer - Maple 24" x 96" 3/8" Dowels - Birch Bed Connector Hardware I-Semble Platform Bed Frame - Queen 3/8" Beadlock Basic Starter
More informationTilt-Top Table. Clean lines and a clever pivot highlight this attractive and useful table
Tilt-Top Table READY FOR DINNER swing the top down and you have a beautiful table ready for a cozy meal. 60 SMALL FOOTPRINT with the top swung up, the table fits neatly against a wall, freeing up floor
More informationSilverware Chest Plan
Silverware Chest Plan 05L14.01 Introduction 1. Measure the space required for your cutlery before beginning this project to be sure that it will fit in the drawers and top compartment. The best way to
More informationJeff Branch WOODWORKING YOU CAN BUILD A. By adding subtle design elements, a traditional furniture style becomes decidedly modern.
Jeff Branch WOODWORKING YOU CAN BUILD A By adding subtle design elements, a traditional furniture style becomes decidedly modern. Jeff Branch WOODWORKING Publisher: Jeff Branch Editor: Jeff Branch Art
More informationFloating-Top Table. Creative joinery adds spark to this versatile piece
Floating-Top Table Creative joinery adds spark to this versatile piece By Michael Pekovich 28 FINE woodworking This is one of those projects that almost wasn t. Rachel, my wife, had asked for a small,
More informationApartment Dining Table
Jeff Branch WOODWORKING You Can Build an Apartment Dining Table By JEFF BRANCH H ave you ever found yourself wanting a new piece of furniture, but everything you see in stores is too big? Big furniture
More informationHow to Build a Recessed Medicine Cabinet
How to Build a Recessed Medicine Cabinet See post for install info http://www.hertoolbelt.com/recessed-medicine-cabinet/ Materials 6 Inset Cabinet Door Hinges 3 Latches 1 sheet Beadboard or 1/4 plywood
More informationServing Tray. When some good friends got married recently, An exercise in template-making yields a great gift project that s easy to duplicate
Serving Tray An exercise in template-making yields a great gift project that s easy to duplicate END Create from 3 8 2 8" piece. By Geoff Noden When some good friends got married recently, I decided to
More informationProject 17884EZ: Shaker End Table
Project 17884EZ: Shaker End Table With its clean, simple lines, this piece is unmistakably Shaker style. Ours is made from cherry, a wood commonly used by Shaker craftsman, but we ve also seen this piece
More informationKitchen Upper Cabinet: Double Doors Cabinets from Scratch
Kitchen Upper Cabinet: Double Doors by Cabinets from Scratch Our Home from Scratch LLC Page 1 Disclaimer Our Home from Scratch LLC and its legal owners cannot be held responsible for any loss, damage,
More informationButterfly Leaf Dining Table Plans
Butterfly Leaf Dining Table Plans Part 1 An attractive dining table with a secret: the leaf folds and stores inside the table. Season 1, Episode 7 P a g e 2 I first saw a butterfly leaf table in a back
More informationMATERIALS: TOOLS: CUT LIST:
MATERIALS: (3) 4x4x8 Ft. Boards (8) 2x4x8 Ft. Boards 2 ½-inch Pocket Screws 2 ½-inch Wood Screws 1-inch Wood Screws (16) Figure 8 Tabletop Fasteners Wood Glue Wood Filler TOOLS: Tape Measure Pencil Carpenter
More informationThis is a solid wood cabinet. The only plywood used is for the back and drawer bottoms.
Sideboard Sideboard Overview: This project requires basic woodworking skills and access to woodworking machines. Woodworking machines have sharp cutting edges and are NOT forgiving. You should be properly
More informationShoulder Plane. dovetailed. fine tools. Make an heirloom tool and learn the secret to creating double dovetails in metal it s easier than you think.
fine tools dovetailed Shoulder Plane Make an heirloom tool and learn the secret to creating double dovetails in metal it s easier than you think. I ve always been fascinated by old, metal hand planes.
More informationFront Vise 70G G08.02
Front Vise 70G08.01 70G08.02 The following instructions guide you through the installation of either the Regular Front Vise (70G08.01) or the Large Front Vise (70G08.02). The first step is to determine
More informationShaker Lap Desk. The classic Shaker lap desk, designed two centuries ago to. Celebrate pen and ink with this quintessential case
Shaker Lap Desk Celebrate pen and ink with this quintessential case BY CHRISTIAN BECKSVOORT The classic Shaker lap desk, designed two centuries ago to function as a miniature traveling office, was the
More informationAmerica s leading woodworking authority To download these plans, you will need Adobe Reader installed on your computer. If you want to get a free copy, visit: http://adobe.com/ reader. Having trouble downloading
More informationGrade 11 Woods Lift Lid Coffee Table. Based on Under the big Top from Popular Mechanics Website
Grade 11 Woods Lift Lid Coffee Table Based on Under the big Top from Popular Mechanics Website TABLE TOP 1. Select enough lumber to construct a top that is between 22 ½ and 24 wide after jointing. Ensure
More informationCorner Cupboard. This space-saving piece enhances any room 46 FINE WOODWORKING
Corner Cupboard This space-saving piece enhances any room BY G A R R E T T H A C K On every trip to the Shelburne Museum near Burlington, Vt., I visit a favorite object a small hanging corner cabinet.
More informationHinge Mortising Jig. One of the make it or break it parts of building a. 6 ShopNotes No. 74
Hinge Mortising Jig A Mortise for a Hinge. Quick, clean, and accurate that s the only way to describe the mortise you get with a trim router and this hinge mortising jig. One of the make it or break it
More informationFlush Trimmer Jig By Santanu Lahiri
Flush Trimmer Jig By Santanu Lahiri I found this jig in a book published by the Fine Woodworking people: Ingenious Jigs And Shop Accessories, publisher Taunton Press, ISBN# 1-56158-296-4. The Author is
More informationProject 13586EZ: Writing Desk. Writing Desk Materials List
Project 13586EZ: Writing Desk This writing desk will make a handsome addition to just about any room in the house. The one shown is made of cherry, a logical choice for a piece like this, but mahogany
More informationDress up your dining room with this Southern delicacy. that was used to serve drinks after a hunt. Breeches and jodhpurs are optional.
Dress up your dining room with this Southern delicacy that was used to serve drinks after a hunt. Breeches and jodhpurs are optional. Huntboard Classic Six-Legged My dad has been making this six-legged
More informationA candle stick addresses transferring and reproducing dimensions from a plan and breaking the project into steps.
Activities Discussion These projects allow more skill development including making items to match a drawing, sizing projects to specific dimensions, and just trying fun stuff for the first time! A candle
More informationKitchen Upper Cabinet: Single Door Cabinets from Scratch
Kitchen Upper Cabinet: Single Door by Cabinets from Scratch Our Home from Scratch LLC Page 1 Disclaimer Our Home from Scratch LLC and its legal owners cannot be held responsible for any loss, damage, disappointment,
More informationWindsor Chair Online. Assembly Instructions
Windsor Chair Online Assembly Instructions Date: 1/4/2007 Other Chairs Offered Philadelphia Arm Chair New England Comb Back Sackback d Arm Chair Bow Back Side Chair Fan Back Side Chair Page 1 Table of
More informationClassic Project. Contemporary Table. In this plan you ll find: Step-by-step construction instruction. A complete bill of materials.
America s leading woodworking authority Classic Project In this plan you ll find: Step-by-step construction instruction. Contemporary Table A complete bill of materials. Construction drawings and related
More informationAhead of the curve 2 Part
F&C PROJECT Ahead of the curve 2 Part In the second part of this series, Chris Tribe constructs the table for his stylised cabinet which we looked at last month in F&C Accuracy in turning the legs for
More informationClassic Kitchen Island
America s leading woodworking authority Step by Step construction instruction. A complete bill of materials. Classic Kitchen Island Exploded view and elevation drawings. How-to photos with instructive
More informationShopBot Quilt Rack Project
ShopBot Quilt Rack Project DISCLAIMER All CNC machines are potentially dangerous and because ShopBot Tools, Inc. has no control over how the project described in this manual might be used. ShopBot Tools,
More information135 ROLLTOP DESK 515
135 ROLLTOP DESK 515 For the person who hates to clear off a desk, who wants to leave everything where it is overnight yet still have the clutter hidden, a rolltop desk is a godsend. The tambour hides
More informationAbout.com :
http://woodworking.about.com/gi/dynamic/offsite.htm?sit...//www.popularwoodworking.com/features/fea.asp%3fid=1088 (1 of 8)1/28/2004 12:05:01 AM Modern Storage Tower The last thing I want to do when starting
More informationProject 13519EZ: Shaker Sewing Desk
Project 13519EZ: Shaker Sewing Desk This fine example of a Shaker sewing desk was measured and photographed at Hancock Shaker Village in Hancock, Massachusetts. On the original, the legs and various frame
More informationChristmas Bell Ornament
Christmas Bell Ornament This is an easy Christmas ornament idea I cabbaged from a friend and skilled turner, Curt Fuller, from Utah. I kind of adapted it to my style but I still got the idea from him.
More informationwoodworkersjournal.com MATERIAL LIST
MATERIAL LIST T x W x L 1 Legs (2) 1 1 2" x 3 1 2" x 36 7 16" 2 End Uprights (2) 1 1 2" x 3 1 2" x 32 1 2" 3 Stringers (4) 1 1 2" x 3 1 2" x 42" 4 Top Cladding, Long (2) 3/4" x 7 1 4" x 65 3 4" 5 Side
More informationThree Legged Stool. Randy Cordle / 2016
Three Legged Stool Randy Cordle / 2016 This stool could easily qualify as fine furniture, being equally at home in the living room or featured at the local arts and crafts fair. A few unique construction
More informationDOCUMENT CHEST. Curly Maple, White Pine
25 DOCUMENT CHEST Curly Maple, White Pine 100 MAKING THE DOCUMENT CHEST After the stock has been thicknessed, ripped to width, and cut to length, plough a 1/4" X 3 /8" groove on the inside faces of the
More informationcraftsman rocker Classic style meets comfort in this sturdy oak rocking chair BY MICHAEL PEKOVICH 34 FiNE woodworking
craftsman rocker Classic style meets comfort in this sturdy oak rocking chair BY MICHAEL PEKOVICH 34 FiNE woodworking photo, this page: Michael pekovich shape the rear legs designing a chair can be a tough
More informationCorner Cabinet. American. There is something about corner cabinets that spooks
American Corner Cabinet The triangular shape of this project puts off most woodworkers. Here s a secret: It s actually quite easy to build. There is something about corner cabinets that spooks most woodworkers.
More informationFlamingo. That s what I looked
Plans N O W w w w. P l a n s N O W. c o m flip-seat Storage Bench Flamingo. That s what I looked like as I stood in the doorway perched on one leg, with my other foot raised so that I could untie the laces
More informationMudroom Unit. Page 1 of 25
Mudroom Unit www.andrewharriswoodwork.com Page 1 of 25 Introduction This plan makes a unit which is 66 ¾ inches tall, 39 ½ inches wide and 18 ½ inches deep. It was custom made for some friends to fit the
More informationCheap, Sturdy Workbench Christopher Swingley
Introduction heap, Sturdy Workbench hristopher Swingley The following bench is an inexpensive version of the Roubo workbenches shown in The Workbench ook by Scott Landis [1]. It s basically just a sturdy
More informationDemilune 4. Apron Joinery. Curved Apron Tenon. Bridle Joint Legs. Bridle Joint Front Apron
Demilune Email 4 Apron Joinery There are two types of joints used in connecting the aprons and legs. The rear legs use conventional mortise and tenon joints, while the front legs use the less conventional
More informationULTIMATE ROUTER TABLE PLANS. By Dan Phalen
ULTIMATE ROUTER TABLE PLANS By Dan Phalen January 2017 Ultimate Router Table Plans. Copyright 2012-2017 by Daniel Phalen. Published by Creston Hall Publishing Company. All rights reserved. No part of this
More informationMaking a Massive Bookcase Step-by-Step
Making a Massive Bookcase Step-by-Step Jeff Branch WOODWORKING The only thing challenging about this project is its huge size. By JFF BRANCH A t right is a rendering of my first woodworking project completed
More informationI love the outdoors. And I m impressed with whatever forces in the universe have made it possible for me to purchase a collapsible canvasand-metal
Limbert Chair 9 I love the outdoors. And I m impressed with whatever forces in the universe have made it possible for me to purchase a collapsible canvasand-metal camp chair for under $20. But when you
More informationShaker Classic Change the legs to change the look
Shaker Classic Change the legs to change the look 2 Ways B Y C H R I S T I A N BECKSVOORT not long ago, a couple ordered a set of cherry side tables from me, one for each side of their pencil-post bed.
More informationVCE VET FURNISHING (CABINET MAKING)
Victorian Certificate of Education 2012 SUPERVISOR TO ATTACH PROCESSING LABEL HERE STUDENT NUMBER Letter Figures Words VCE VET FURNISHING (CABINET MAKING) Written examination Section Monday 12 November
More informationBuild a Stout Workbench
Build a Stout Workbench Tail vise is at the heart of this versatile bench by chris gochnour I ve done a fair amount of handplaning during my 32 years as a professional furniture maker, and I ve found that
More informationA Shaker Sewing Stand
America s leading woodworking authority Step by Step construction instruction. A Shaker Sewing Stand A complete bill of materials. Exploded view and elevation drawings. How-to photos with instructive captions.
More information129 KITCHEN BASE CABINET 480
129 KITCHEN BASE CABINET 480 There are two sorts of kitchen cabinets: base cabinets, which sit on the floor, and wall cabinets. Base cabinets provide both storage space and work surfaces. They often house
More informationCROTCH-GRAINED CHESS TABLE. Walnut, Poplar
3 CROTCH-GRAINED CHESS TABLE Walnut, Poplar 11 MAKING THE CHESS TABLE This piece is designed around a set of angles taken from the playing pieces, angles echoed in the fat dovetails holding the stretchers
More informationALWAYS disconnect the power source before using the Betterley UNA-GAUGE with any power tool or machine!
Betterley UNA-GAUGE Thank you for purchasing the Betterley UNA-GAUGE. You will find the UNA-GAUGE provides quick adjustments and alignment of most tools and machinery with extreme accuracy. The versatile
More informationhanging mirror Two-piece desk set Handmade Gifts Photo: John Tetreault
hanging mirror Two-piece desk set Handmade Gifts 44 FINE woodworking Photo: John Tetreault Flatware carrier Tea light candle holder 4 Tasteful projects made quickly from scraps BY CHRISTIAN BECKSVOORT
More informationSuspension/Flogging Rack Design
This is a rack that can be transported and set up by one person, requires no tools for set up and has no bolts. Structurally it goes together using mortis and tenon joints. It can be used for suspensions
More informationPro-Doweling Kit USER S MANUAL #840. Visit us at
Pro-Doweling Kit USER S MANUAL #840 99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com Please read this manual carefully and thoroughly
More informationI then moved on to the legs assemblies. The legs are simply three pieces of 1 ½ in x 4 ¼ in stock glued up, planed and jointed to 4 in x 4in.
Nicholson Workbench Another workbench? Does this guy have nothing better to do than build one workbench after another? First off, this one is not for me. I recently received a commission to build a Nicholson
More information15 Dovetail Jig. Instruction Manual. Part # 3452
15 Dovetail Jig Instruction Manual Part # 3452 CAUTION: Please read, understand, and follow all manufacturers instructions, guidelines and owners manuals that come with your power tools. Peachtree Woodworking
More informationKnockdown Bookcase. This slant-sided bookcase was a popular mail-order item in the early 1900s.
Knockdown Bookcase This slant-sided bookcase was a popular mail-order item in the early 1900s. The Arts & Crafts movement was part of an interesting social change in America the advent of mail-order purchases.
More informationA quick and easy way to make a hidden reinforced miter joint
A quick and easy way to make a hidden reinforced miter joint Text and photos by Jerry Work 2011 Carefully mitered corners add a touch of elegance to any square or rectangular piece. The problem is they
More informationMedia Center Woodworking Plans Our Home from Scratch
Media Center Woodworking Plans by Our Home from Scratch Our Home from Scratch LLC Page 1 Disclaimer Our Home from Scratch LLC and its legal owners cannot be held responsible for any loss, damage, injury
More informationComputer Desk. Project designed by April Wilkerson
Project designed by April Wilkerson Copyright WilkerDos.com 2018 Project plan Desk Page 2 of 16 Page 3 of 16 File cabinet Page 4 of 16 Metal base Page 5 of 16 Glue up Get started by gluing up boards for
More informationBuild a Michigan Sloyd. Spoon Mule
Build a Michigan Sloyd Spoon Mule Contents Materials Choosing and milling wood.... 3 Base Legs.... 4 Rails.... 5 Seat Assembly and shaping...10 Fin options....10 Riser Assembly....11 Wedge....12 Head Laminations....13
More informationDesign Considerations
Alan N. Leland Miniature Stool Design Considerations The seat of the stool is the most visible part of the stool therefore; using a figured wood will enhance the overall appeal of the finished stool. The
More informationWOODWORKING GUIDE: BASIC JOINERY
WOODWORKING GUIDE: BASIC JOINERY Close isn't really good enough. A perfect fit is what counts. When building furniture, there are many ways to construct joints. The simplest are those that use mechanical
More informationCopyright 2010 Springbok Publishing All Rights Reserved- Page 1
Copyright 2010 Springbok Publishing All Rights Reserved- www.woodensaddlerackplans.com Page 1 Legal Information All contents copyright 2010 by Springbok Publishing. All rights reserved. No part of this
More informationARCHED AURORA NIGHTSTAND BY DARRELL PEART
ARCHED AURORA NIGHTSTAND BY DARRELL PEART If my furniture making business were a corporation, the shareholders would have thrown me out a long time ago. My approach is impractical, because I d rather tinker
More informationWagon Vise Retrofit Installation Instructions. American Craft Woodworks. Wagon Vise
Wagon Vise Retrofit Installation Instructions American Craft Woodworks Wagon Vise Wagon Vise Retrofit Installation Instructions 2 Retrofit Installation Instructions Before you get started, please read
More informationEntrance Cabinet Plans
Entrance Cabinet Plans www.andrewharriswoodwork.com Page 1 of 19 Introduction I have tried to ensure all steps are covered in these plans but if you find any errors in the plans or have a question then
More informationCastle Bed. Page 1 of 24
Castle Bed www.andrewharriswoodwork.com Page 1 of 24 Introduction This plan makes a twin bed that is 91 inches long and 60 inches wide. I have tried to ensure all steps are covered in these plans but if
More informationKitchen Base Cabinet: Single Drawer with Double Doors Cabinets from Scratch
Kitchen Base Cabinet: Single Drawer with Double Doors by Cabinets from Scratch Our Home from Scratch LLC Page 1 Disclaimer Our Home from Scratch LLC and its legal owners cannot be held responsible for
More informationYOU CAN BUILD THE JACKSON DRESSER. Combining traditional styling with rustic materials leads to a classic, yet casual look.
YOU CAN BUILD THE JACKSON DRESSER Combining traditional styling with rustic materials leads to a classic, yet casual look. Jeff Branch CONTENTS Jeff Branch Publisher: Jeff Branch Editor-in-Chief: Jeff
More informationCopyright 1998 KDE Technologies
Modular Computer Corner Desk Unit Copyright 1998 KDE Technologies http://members.tripod.com/~kdetech/ 1. Introduction 2. Plans Sheet one - Isometric Sheet two - Top Detail / Corner Unit Sheet three - Leg
More informationThis tailor s cabinet was brought to my attention by a customer
So what if you don t sew? This authentic Shaker case piece is drop-dead gorgeous in any room. This tailor s cabinet was brought to my attention by a customer who wanted one just like it. She had seen the
More informationSmoker. Written By: Feitan
Smoker Smoking meat has been around for hundreds of years. Now with this simple smoker one can bring back to life the ancient methods of preserving meats and adding the smoky flavor. Written By: Feitan
More informationI I. . i1 AD JUSTABLE SHELVES
ADJUSTABLE SHELVES HAD BEEN TRYNG TO WORK out a really simple (read "fast") way to make an elegant wooden version of the old standby, metal standards and brackets. Although have seen many commercial versions
More informationA Table for Four... with a View
America s leading woodworking authority Step by Step construction instruction. A Table for Four... with a View A complete bill of materials. Exploded view and elevation drawings. How-to photos with instructive
More informationPristine Precise Perfection
Pristine Precise Perfection EB TY Premium Hidden Deck Fastening System For Premium Timber Deck Applications Stainless Steel Reinforced EB- GUIDE EB-TY Premium Hidden Deck-Fastening System Optimise Your
More informationTurning a Duck by Fred Holder
Turning a Duck by Fred Holder Back in 2004, Guilo Marcolongo, a turner from Australia, demonstrated how to turn a Daffy Duck at the Utah Symposium. I decided to try one. Here s my process, with some photos
More information1 ¼-inch Pocket Screws Brad Nailer or Hammer 1 ¼-inch Brad Nails Clamps
MATERIALS: TOOLS: (4) 2 x 6 x 8 Ft. Boards Tape Measure (2) 2 x 4 x 8 Ft. Boards Carpenter s Square (7) 1 x 4 x 8 Ft. Boards Pencil (2) 1 x 3 x 8 Ft. Boards Drill (1) Half Sheet of ¾-inch Thick Plywood
More informationProject: Smoker Overview: Smoking meat has been around for. Materials: 3/4 plywood, 7-48 of 1/2 dowel,
Project: Smoker Overview: Smoking meat has been around for hundreds of years. Now with this simple smoker one can bring back to life the ancient methods of preserving meats and adding the smoky flavor.
More informationFramework joints FABRICATION - WOOD JOINTS. Corner joints. Tee joints. Worksheet 15a. Cable Educational Ltd
FABRICATION - WOOD JOINTS The word: fabricate means to join together. Most wooden products are held together with adhesive. Adhesive works very well when the edge of a piece of wood is being glued to the
More informationSIDE CAR BED. By BRWC Member Jim Landry
SIDE CAR BED By BRWC Member Jim Landry My wife asked if I could make a Side Car Bed for a friend of hers that was having a baby. My first response was, What is a Side Car Bed? Well, I did some research
More informationMake your own zero clearance throat plate.
Make your own zero clearance throat plate. A picture tutorial By Wayne Breshears One of the more important table saw accessories you can have is a zero clearance insert or throat plate. The close tolerance
More informationYou Can Build a Bedside Table
You Can Build a Bedside Table Jeff Branch WOODWORKING If you like making panels, you ll love this project. By JEFF BRANCH M y current home is a modest one. But it is a big improvement over our small starter
More informationThe image above is intended to give you an idea of what the dovecote will look like when finished.
Thank you for buying my book, I hope it is useful and enjoyable in your quest to building your own dovecote. This book will give you step-by step instructions on how to build your own dovecote also included
More informationGENERAL NOTES: Page 1 of 9
Laminating A Zia Into A Turning Blank by W. H. Kloepping, Jan. 2009 This describes how a zia (the New Mexico state symbol) can be laminated into a turning blank. Materials needed: Square Turning Block
More informationNational 5 Practical Woodwork
Exercise C. The legs of a chair are turned on the wood lathe. (a) (i) Sketch and name the tool used to produce the square shoulder shown at A. Name of tool: Sketch and name the tool used to check the diameter
More informationChest of Drawers Plans
Chest of Drawers Plans www.andrewharriswoodwork.com Page 1 of 15 Introduction This plan makes a chest of drawers that is 50 inches at the widest point, 19 inches deep and 40.75 inches high. I have tried
More informationThe saw is not a decoration piece but sees regular use at the school. The cross pieces at either end are made from oak, the long stretchers are made
Roy s Saw When you walk in the front door of Roy Underhill s Woodright s School and look to your left in the window hanging above Roy s stuffed chicken is a large frame saw. Now the chicken is an interesting
More information