Guide Pulley System [GPS]
|
|
- Sophia Waters
- 5 years ago
- Views:
Transcription
1 Guide Pulley System [GPS] The purpose of the guide pulley system is to guide the wire from the dancer pulley system to the guide rollers. Two of these systems exist: on both sides of the machine. The pulley bracket can be manually adjusted to line up with the appropriate grooves on the guide rollers. The guide pulley system is located in the space associated with the guide roller system. This is a very simple system with only four main parts. It must only meet a few engineering and customer requirements. A COMSOL model demonstrates that the system is subject to minimal displacement under extreme loading conditions. Stress levels are also within allowable limits.
2 Guide Pulley Rod [GPS201] The guide pulley rod is a hollow steel square extrusion with a half inch width. This rod holds the rest of the guide pulley assembly and attaches directly to the frame associated with the guide roller system. This extrusion can be commonly found at hardware stores, specifically Home Depot. A standard length of three feet from Home Depot (PRT#: 40290) is sufficient for both guide pulley systems. Additionally, a standard shaft collar from McMaster fits this extrusion perfectly. The rod would need to be cut to length and possibly coated for resistance against slurry. As shown in the overall finite element force analysis, the rod is able to withstand maximum stress and displacement forces.
3 Guide Pulley Collar [GPS202] The guide pulley collar clamps to the guide pulley rod and is attached to the guide pulley bracket. The two halves are separable, allowing the collar to be adjusted along the length of the rod so that the wire coming off of the guide pulley aligns with the correct groove on the guide rollers. This is a slightly modified standard part from McMaster. It meets the customer requirement of allowing for an adjustable position for the guide pulley. A standard shaft collar (PRT#: 3325K15) will be purchased from McMaster and the following modifications will be made: Re-tap existing holes with M6x1 threading Increase bores sizes to 0.43 inches in diameter Drill two holes in two parts as shown in drawing and tap with M6x1 thread The modified part meets all customer and engineering requirements. Adjustable screws are in metric units as requested. Stress and displacement levels are within allowable limits.
4 Guide Pulley Bracket [GPS203] The guide pulley bracket attaches to the guide pulley collar and holds the pulley assembly. The bracket is designed to position the pulley symmetrically to distribute the tensile load evenly and to ensure that the adjustable cap screws are easily accessible. This is a simple part, but it is designed with ease of manufacture and usability in mind. The slotted sections allow for the entire bracket to be removed and for the collar to be adjusted easily. With the pulley hanging below the rod, both the cap screws and the pulley are conveniently accessible for observation and adjustment. The part is designed to be cut out of a sheet of steel using a water jet, CNC router or laser cutter and bent to shape. A recommended bend radius is included for the specified sheet thickness. This part is the most at risk when it comes to stress and displacement under tensile forces. However, the finite element analysis shows values that are not unreasonable. It is possible to modify this part by increasing the thickness to ensure durability.
5 Guide Pulley Cap Screws [GPS001] This standard part allows the position of guide pulley collar to be adjusted. It also attaches the guide pulley bracket to guide pulley collar. According to customer requirements, it is adjustable using standard metric hex key. A standard M6x1 cap screw is nearly perfectly equivalent to a ¼-28 cap screw. The guide pulley collar is a standard part from McMaster with tapped holes for ¼-28 cap screws. Standard M6x1 cap screw will be purchased. No modifications are necessary. Physical tests of over tapping ¼-28 thread with M6x1 thread proved to be successful. A half inch thick block of steel was used.
Leveling Feet, Base Plates and Casters
Leveling Feet, Base Plates and Casters 77 Leveling Foot 1 1 Fastening to profile end Fastening in T-slot of profile For leveling tables and light equipment. Ratchet-type height adjustment requires no tools.
More informationCRP700 Benchtop Basic CNC Machine Assembly Instructions. Updated 10/24/2014 SHEET 1 of 24
CRP700 Benchtop Basic CNC Machine Assembly Instructions Updated 0//0 SHEET of NOTE: This piece of extrusion is mounted wide side up Quick Tip: Lay extrusion on table as shown for easy assembly BASE ASSEMBLY:.
More informationUltra-High Precision Indexer
Ultra-High Precision Indexer STR-Series Reducer Installa on Manual Contents 1 STR exploded view...2 2 Reducer installation... 2-6 3 Reducer removal... 7 4 Screws... 8 5 Tightening torque... 9 1 STR exploded
More informationINSTALLATION INSTRUCTIONS FOR HAND OPERATED SILENT STEEL ADC HEAVY DUTY CURTAIN TRACK MODELS: 280, 281, 282, 280-A, 283-N, 283-R
INSTALLATION INSTRUCTIONS FOR HAND OPERATED SILENT STEEL ADC HEAVY DUTY CURTAIN TRACK MODELS: 280, 281, 282, 280-A, 283-N, 283-R I. SUSPENDED INSTALLATIONS 1. Lay the two track halves on the floor with
More informationHOME WORKSHOP HANDBOOK Rugged BENCH GRINDER. By JOEL B. LONG
6 HOME WORKSHOP HANDBOOK Rugged BENCH GRINDER W By JOEL B. LONG ITH this bench grinder you can keep your cutting tools sharp and do general offhand grinding, and can, with the aid of various attachments,
More informationMounting the 6 or 12 Indexer on PRS Gantry Tools
Page 1 Mounting the 6 or 12 Indexer on PRS Gantry Tools About this guide: This document illustrates several options for mounting an indexer onto your ShopBot. You can choose the technique that works best
More informationIIHS Side Impact Outrigger
IIHS Side Impact Outrigger Assembly Procedure Base Assembly (14.3 lbs) The base assembly consists of a ¼ thick steel plate, a ¼ thick piece of polyethylene, and mounting fixtures for the upper and lower
More informationOX CNC. Mechanical Assembly Instructions. S.A. Brown & Maker Store
OX CNC Mechanical Assembly Instructions S.A. Brown & Maker Store v1.2 07 2017 Contents About The Maker Store Ox CNC Kit... 2 Unpack and Check All Components... 2 Tools Required... 2 Pre-Assembly Notes...
More informationChain Drive Vise. Installation Instructions. (revised 05/04/2016)
Chain Drive Vise Installation Instructions (revised 05/04/2016) Lie-Nielsen Chain Drive Vise Instructions Table of Contents page About Your Chain Drive Vise 3 Parts List 4 Exploded Parts Diagram 5 step
More informationCARIBBEAN EXAMINATIONS SECONDARY EDUCATION CERTIFICATE EXAMINATION MECHANICAL ENGINEERING TECHNOLOGY. Paper 02 - Technical Proficiency.
FORM TP 2011094 CARIBBEAN EXAMINATIONS SECONDARY EDUCATION CERTIFICATE EXAMINATION TEST CODE 01335020 COUNCIL MECHANICAL ENGINEERING TECHNOLOGY Paper 02 - Technical Proficiency 2'h hours MAY/JUNE 2011
More informationAMETAL SHAPER is indispensable for certain METAL SHAPER FOR YOUR SHOP. By S. S. Miner
METAL SHAPER FOR YOUR SHOP By S. S. Miner AMETAL SHAPER is indispensable for certain machining operations where flat surfaces must be produced within very close limits, such as machining flats on castings,
More informationOPERATOR ADAPTER APCABVA
OPERATOR ADAPTER APCABVA Installation Instructions for Allen-Bradley Bulletin 1494V (Variable Depth) 1494C, 140G and 140U Cable Controlled For floor-mounted enclosures with disconnect on the right flange
More informationROYAL ULTRA-PRECISION ER COLLETS " TIR
ROYAL C EXPANDING COLLETS q Unlike chucks and most collets that grip the OD of a workpiece, C expanding collets are designed to grip on the ID of a part. q Accu-length design ensures precise workpiece
More informationWoody s Workshop Tooling for Clock Making
Using the Sherline Headstock Motor for Clock Wheel cutting. Background In order to cut clock wheels on a lathe it is necessary to have a method of indexing the lathe chuck to the correct number of teeth
More informationTOOLS/PROCESSING SERVICES TOOLS + PROCESSING SERVICES
TOOLS/PROCESSING SERVICES 7 TOOLS + PROCESSING SERVICES MINITEC PROFILE SYSTEM 583 TOOLS/PROCESSING SERVICES TOOLS s l oot TOOLS 584 MINITEC PROFILE SYSTEM BALL-HEADED KEY - Chrome plated, with handle
More informationContrivance. sample. a modular mechanism machine. design by Derek Hugger. Important:
sample Important: McMaster Carr, a supplier whose part numbers are referenced throughout this document, can only ship within the United States. Builders outside of the U.S. must find an alternate supplier
More informationLMI Bending Machine. Photo 1. Photo 2. Photo 3. Photo 5. Photo 4
LMI Bending Machine Watch the instructional DVD shipped with the LMI Bending Machine prior to assembling or using it. Note the bending head assembly has been changed since these photos were taken. Operationally
More informationInstallation Instructions: Bumper (Part # SB76850) XJ Jeep Cherokee XRC Rear Bumper
NOTE: Carefully read entire instructions thoroughly before attempting to install this part. Parts Included Qty 93-7789 XJ XRC 1 93-7807 Bumper Mount Bracket: Drvr 1 93-7811 Bumper Mount Bracket: Pass 1
More informationPart 7 Assembling the X axis
Part 7 Assembling the X axis 1 2 The X axis is a key part of the printer, it carries the extruder on a carriage that moves the extruder laterally in the X axis. The x axis itself is moved vertically on
More informationCNC Router Parts PRO Machine Kit Cable Track Installation Instructions
1 1 X CABLE TRACK TRAYS & BRACKETS The cable track on the side of the system is supported by a metal tray (or multiple trays for longer systems such as a PRO4896). These trays hang from brackets on the
More informationRetractable Pool Cover
Retractable Pool Cover By: Abdulhadi Alkhaldi, Zachary Keller, Cody Maurice, Bradley Miller, and Patrick Weber Team 12 Midpoint Review Document Submitted towards partial fulfillment of the requirements
More informationLEG CURL IP-S1315 INSTALLATION INSTRUCTIONS
LEG CURL IP-S35 INSTALLATION INSTRUCTIONS Copyright 2009. Star Trac by Unisen, Inc. All rights reserved, including those to reproduce this book or parts thereof in any form without first obtaining written
More informationINSTALLATION INSTRUCTIONS FOR HAND OPERATED MODELS: 170, 171-R, 171-N, 172, 260
INSTALLATION INSTRUCTIONS FOR HAND OPERATED MODELS: 170, 171-R, 171-N, 172, 260 I. SUSPENDED INSTALLATIONS NOTE: MODEL 260 FENSTEEL TRACK IS ASSEMBLED IN THE SAME MANNER AS DESCRIBED BELOW WITH THE EXCEPTION
More informationV twin cylinder steam engine
V twin cylinder steam engine I got inspired to make this V twin steam engine after reading R. Griffinn s build articles in ME 4396. It is based on Stuart s V-twin double-acting oscillator, but since I
More informationFactory Assistance: Phone: Fax: Page 1
CABLE RUNWAY ACCESSORIES Radius Drop / Stringer Drop Provides 3 bend radius Radius drop fits 6, 12 and 18 runway made from 1-1/2 x 3/8 tubing Steel construction Includes (3) cable spools, (1) bolt, (1)
More informationMechanical Drawing. Fig 5-1
College of Engineering 1 Mechanical Drawing Mechanical Engineering Department Mechanical Drawing Lecture 5 Keys and keyways 5-1 Introduction A key, Fig. 5.1, is usually made from steel and is inserted
More informationCRP700 Benchtop Basic CNC Machine Assembly Instructions. Updated 9/11/2014 SHEET 1 of 25
CRP700 Benchtop Basic CNC Machine Assembly Instructions Updated 9//0 SHEET of NOTE: This piece of extrusion is mounted wide side up Quick Tip: Lay extrusion on table as shown for easy assembly BASE ASSEMBLY:.
More informationTHE GATE COACHAll Rights Reserved 28, Jia Sarai N.Delhi ,-9998
1 P a g e 1 DESIGN AGAINST STATIC AND FLUCTUATING LOADS 2 SHAFT, KEYS AND COUPLINGS CONTENTS Introduction 6 Factor of safety 6 Stress concentration 7 Stress concentration factors 8 Reduction of stress
More informationNote - the nose ribs and are thinner than the main ribs. These nose ribs will use a thinner rib cap than the ribs. This is per design.
Stabilizer rev 1.2 The SE5a stabilizer is the heartbeat of the tail and is recreated like the full scale version. All tail pieces depend on the stabilizer. It uses the steel fittings, pulleys, inspection
More informationSheet Metal Brake Plans for a 6' Sheet Metal Brake
Sheet Metal Brake Plans for a 6' Sheet Metal Brake,1752'8&7,21 Thank you for purchasing the sheet metal brake plans. The plans include a complete list of material needed and easy to follow steps to build
More informationBHJ Products, Inc. Parts List & Instructions
Product Name: Lifter-Tru Kit for Ford Windsor & SVO Small Block V8 Page 1 of 5 Kit Contents: 2x End Plates 2x 5/8 Threaded Adjustment Sleeves 1x Front Angle Bracket 2x 5/8 Adjustment Sleeve Spacers * 1x
More informationUnit IV Drawing of rods, wires and tubes
Introduction Unit IV Drawing of rods, wires and tubes Drawing is a process in which the material is pulled through a die by means of a tensile force. Usually the constant cross section is circular (bar,
More informationThreaded Fasteners 2. Shigley s Mechanical Engineering Design
Threaded Fasteners 2 Bolted Joint Stiffnesses During bolt preload bolt is stretched members in grip are compressed When external load P is applied Bolt stretches further Members in grip uncompress some
More informationGear Drive Hapkit Assembly Instructions
Gear Drive Hapkit Assembly Instructions (1) Order and Print the necessary parts Figure 1: 3D Printed Parts and Hardware Note: The screws shown were replaced with button head screws and the second pair
More informationReplacement of Pitch Link Retainer and Service Improvement of the Pitch Control System. Effectivity: Helicopters manufactured prior to January, 1981
Page 1 of 12 Date: December 2, 1981 Subject: Models: Replacement of Pitch Link Retainer and Service Improvement of the Pitch Control System F-28C and 280C Effectivity: Helicopters manufactured prior to
More informationMTS-SP100. RENOGY Pole Mount System E Philadelphia St, Ontario, CA Version: 1.2
MTS-SP100 RENOGY Pole Mount System 2775 E Philadelphia St, Ontario, CA 91761 1-800-330-8678 1 Version: 1.2 Important Safety Instructions Please save these instructions. This manual contains important safety,
More informationPTC Model 4. Programmable Turntable Controller. Basic Motor Mount Kit P/N Installation Instructions
PTC Model 4 Programmable Turntable Controller M Basic Motor Mount Kit P/N 09-820 Installation Instructions New York Railway Supply 625 Aviator Dr Fort Worth TX 76179 (817) 233-5068 http://www.nyrs.com
More informationFIRST TEAM SPORTS, INC.
FIRST TEAM SPORTS, INC. INVADER EZ-CRANK PORTABLE BASKETBALL GOAL ASSEMBLY INSTRUCTIONS Revised - 08/04/10 BILL OF MATERIALS (1) BASE TANK (1) BACKBOARD MOUNT (2) 5/16 X ¾ HEX BOLT (1) LOWER POST (2) SPRING
More informationChain Drive Vise. Installation Instructions. (revised 11/29/2018)
Chain Drive Vise Installation Instructions (revised 11/29/2018) Lie-Nielsen Chain Drive Vise Instructions Table of Contents page About Your Chain Drive Vise 3 Parts List 4 Exploded Parts Diagram 5 step
More informationPrecision made in Germany. As per DIN The heart of a system, versatile and expandable.
1 Precision made in Germany. As per DIN 8606. The heart of a system, versatile and expandable. Main switch with auto-start protection and emergency off. Precision lathe chuck as per DIN 6386 (Ø 100mm).
More informationPVC Fencing Install Instructions
PVC Fencing Install Instructions Step 1-Pounding the Galvanized Steel Posts Call your local area utility company to come mark underground lines before any digging or pounding any posts into the ground.
More informationmm 0.8 mm 28 mm mm 0.8 mm 38 mm
Top Mounted s BESTEST indicators with top mounted dials are supplied with a rectangular bar, swivel clamp, contact point wrench and a certificate of accuracy and traceability in a fitted case. Contact
More informationProFormer Professional Tubing Bender. Part #12485
ProFormer Professional Tubing Bender Part #12485 Eastwood s ProFormer Professional Tubing Bender is designed around a rigid welded steel frame, iron/aluminum die and roller along with a 8 ton jack that
More informationVPN: ISBXLR. Copyright Black Box Corporation. All rights reserved Park Drive Lawrence, PA Fax
VPN: ISBXLR Copyright 2003. Black Box Corporation. All rights reserved. 1000 Park Drive Lawrence, PA 15055-1018 724-746-5500 Fax 724-746-0746 JULY 2003 RM649-R2 RM657 RM664 RM861 RM650 RM658-R2 RM665-R2
More informationStudent, Department of Mechanical Engineering, Knowledge Institute of Technology, Salem, Tamilnadu (1,3)
International Journal of Scientific & Engineering Research, Volume 7, Issue 5, May-2016 11 Combined Drilling and Tapping Machine by using Cone Mechanism N.VENKATESH 1, G.THULASIMANI 2, S.NAVEENKUMAR 3,
More informationPage 1. SureMotion Quick-Start Guide: LARSACC_QS 1st Edition - Revision A 03/15/16. Standard Steel Bolt/Screw Torque Specifications
R K C T I Repair Kit Product Compatibility Repair Kit # Linear Actuator Assembly # LARSACC-013 LARSACC-014 LARSD2-08T12BP2C (12-in travel) LARSD2-08T24BP2C (24-in travel) C P I R K 1 ea Ball Screw with
More informationMECHANICAL ASSEMBLY John Wiley & Sons, Inc. M. P. Groover, Fundamentals of Modern Manufacturing 2/e
MECHANICAL ASSEMBLY Threaded Fasteners Rivets and Eyelets Assembly Methods Based on Interference Fits Other Mechanical Fastening Methods Molding Inserts and Integral Fasteners Design for Assembly Mechanical
More informationStandard drawer runner program
Standard drawer runner program i 230M Single extension, Blumatic self-closing drawer runners s: 250mm (10") to 650mm (26") 230 series drawer runners Cabinet profile Drawer profile Rear mount sockets available
More informationInstallation Instructions for OPGW Bolted Dead End
INS-ACA015 OPGW Bolted Dead End Procedure 1. Disassemble dead end. Remove one bolt from the same side of each keeper. Loosen other bolts to permit conductor to be placed in the conductor groove. If keepers
More informationTOOLING COMPONENTS. Clamping Kits Step Blocks & Kits Driver Studs Bolts, Screws Nuts, Washers...
TOOLING COMPONENTS Clamping Kits... 2-5 Step Blocks & Kits... 6-7 Driver Studs... 8-12 Bolts, Screws... 13-19 Nuts, Washers... 20-29 Clamps... 30-43 Swivel Screw Clamps... 44-46 Screws... 47-48 Hand Knobs...49
More informationDELAWARE DIAMOND KNIVES
DELAWARE DIAMOND KNIVES PHASE 4 REPORT December 10, 2010 By Jeff LeBlanc, Nnamdi Ibeka, David Kim, and Matthew Lindemer Table of Contents Updated Project Scope... 3 New Project Information... 3 Prototype
More informationOnyx 90 Media Cutter. Parts Manual
Parts Manual Professional Picture Frame Equipment 441 South Whitted Street Hendersonville, NC 28739 Thank you for purchasing the Onyx 90 Media Cutter. Please read all instructions before operating your
More informationBy C.W. Woodson From the pages of Model Craftsman magazine June, 1937
By C.W. Woodson From the pages of Model Craftsman magazine June, 1937 As shown in Fig. 1, the tool post grinder for which plans are given here can be used to finish up delicate work to more accurate dimensions
More informationDoor Stop Bracket repair
by Bill Robinson Door Stop Bracket repair If the threads that hold your Door Stop (footman loop) Bracket, or door strap bracket, are stripped and you strap is hanging similar to mine in the photo below,
More informationB-Too Drilling and Tapping Machine Instruction and Maintenance Manual
B-Too Drilling and Tapping Machine Instruction and Maintenance Manual Thank you for your purchase of the B-Too Drilling and Tapping Machine. Please read and understand this short operation manual. Our
More informationINDEX > CH.5 HANGING SUPPORTS TENTI SHELF SUPPORTS TENTI TENTI TENTI - 4C... TENTI TENTI TENTI TENTI
> C.5 ANGING SUPPORTS INDEX SELF SUPPORTS 1-3... 305 2-4... 306 3-4C... 307 4-5... 308 5-7... 309 6-8... 310 7-9... 311 305 > C.5 ANGING SUPPORTS Maximum loads for shelf supports The test levels that shelf
More informationPRS Retro Z-Axis Installation
PRS Retro Z-Axis Installation Page -1- PRS Retro Z-Axis Installation This document is a guide to installing the PRS Retro Z-axis on early ShopBot models. It describes installation for PR models with PK299
More informationFlush Trimmer Jig By Santanu Lahiri
Flush Trimmer Jig By Santanu Lahiri I found this jig in a book published by the Fine Woodworking people: Ingenious Jigs And Shop Accessories, publisher Taunton Press, ISBN# 1-56158-296-4. The Author is
More informationWhat Does A CNC Machining Center Do?
Lesson 2 What Does A CNC Machining Center Do? A CNC machining center is the most popular type of metal cutting CNC machine because it is designed to perform some of the most common types of machining operations.
More informationCNC Router Parts. Standard Rack & Pinion Drive Assembly Instructions
CNC Router Parts Standard Rack & Pinion Drive Tools List The following tools will be used for assembly and installation of the Standard Rack & Pinion Drive: Imperial Allen Wrench Set - 3/32", 5/32", 3/16",
More informationInsolroll Clutch Operated Shades Installation Instructions Installation Instructions
All clutch operated shades are shipped fully assembled and ready for installation. Mounting screws are not provided. Screws for chain guide installation to meet the child safety standards are provided.
More informationSMART ROUTING KIT. Sliding Arm. Perpendicular Stops* Control the movement along the Y-axis. Traveler Two slots for positioning on the Guide Rail
SMART ROUTING KIT The EZ SMART Smart Routing Kit (SRK) is the original routing kit for the EZ SMART system. It turns the average router into a production tool capable of multiple axis routing with CNC-like
More informationAUXILIARY FRAMING AND ACCESSORIES
CUSTOM CABINETS & RACKS STRUT AND ACCESSO- RIES JUNCTION KITS ANGLE AND BRACE KITS SPLICE KITS BRACE KITS INSTALLATION KITS WALL ANGLE KITS RUBBER END CAPS SUPPORT INSTALLATION AND SUPPORT KITS STANCHION
More information3850, Drum & Disc Brake Lathes. Parts Identification
3850, 3860 Drum & Disc Brake Lathes Parts Identification READ these instructions before placing unit in service. KEEP these and other materials delivered with the unit in a binder near the machine for
More informationThe new motor and motor mount. The remote control and 3 axis DRO mounted
Modifying a Mill/Drill I bought this mill/drill about 4 years ago and knew from the very beginning that some changes were going to have to be made. I am a big fan of VFDs (variable frequency drives) to
More informationMetroboard Pulley Replacement Procedure
Metroboard Pulley Replacement Procedure 1) Remove the two transmission cover screws (1/8 allen driver). Then remove the transmission cover. Note there is a split lock washer and flat washer as well, so
More information1. The Lathe. 1.1 Introduction. 1.2 Main parts of a lathe
1. The Lathe 1.1 Introduction Lathe is considered as one of the oldest machine tools and is widely used in industries. It is called as mother of machine tools. It is said that the first screw cutting lathe
More informationLead Screw Cover Installation
The premier source of tooling, parts, and accessories for bench top machinists. Lead Screw Cover Installation These instructions cover two products: 5201 Telescoping Lead Screw Cover, 7x10, 7x12 5202 Telescoping
More informationOffice Partitions WARNING. Assembly Instructions. Customer Service A S S E M B LY HARDWARE H1 H2 H3 H4 H5 H8 H9 H10 H11 H12
Customer Service 1-800-645-2986 Assembly Instructions WARNING In order to prevent structural failure, instability, t i p - o v e r, and/or serious injury, please follow i n s t ructions care f u l l y.
More informationSPARE PARTS LIST MODEL NO. LB1200F PAGE 1 ITEM PART NO. DESCRIPTION QTY NOTE
PAGE 1 001 JM21000018 HEX.SOCKET HEAD SCREW M5X12 4 002 JM21000019 SPRING WASHER 5 4 003 JM21000020 FLAT WASHER 5 4 004 JM21000021 UP COVER COMPLETE 1 005 JM21000025 MICRO SWITCH FIX PANEL A 1 006 JM21000026
More informationBuilding a Universal Panorama Head
Building a Universal Panorama Head Fig 1: Universal Panohead This paper describes the process of building a universal panorama bracket. The intention is to describe the process I used rather than provide
More informationSteel Casework Metal Framing System
MISCELLANEOUS ITEMS Continuous Slot Metal Framing System Installs quickly Completely adjustable Re-usable Eliminates all welding, drilling and use of special tools G23 METAL FRAMING SYSTEM 1. Place the
More informationThe Canadian Tire Paint Roller A Technical Description
A Technical Description Eric Morlang Table of Contents 1. General Description of the Paint Roller... 3 2. Part-By-Part Description of the Paint Roller... 4 2.1 Body... 4 2.1.1 Handle... 4 2.1.2 Wire...
More informationScrews. Introduction. 1. Nuts, bolts and screws used to clamp things together. Screws are used for two purposes:
Screws Introduction Screws are used for two purposes: 1. To clamp things together. 2. To control motion. 1. Nuts, bolts and screws used to clamp things together. Nuts, bolts and screws that are used for
More informationHMP-200 BENDER INSTRUCTION SET
HMP-200 BENDER INSTRUCTION SET HMP-200 BENDER ASEMBLY INSTRUCTIONS STEP 1 STEP 2 BOLT LEFT SIDE PLATE TO BASE AS SHOWN WITH 1/2 x20 HEX BOLT & FLAT WASHER WELD BASE TO PLATE ON EACH SIDE NOTE: OFFSET HOLE
More informationHours / 100 Marks Seat No.
17610 15116 4 Hours / 100 Seat No. Instructions (1) All Questions are Compulsory. (2) Answer each next main Question on a new page. (3) Illustrate your answers with neat sketches wherever necessary. (4)
More informationUseful accessories for lathe and milling systems.
1 Useful accessories for lathe and milling systems. Nearly all accessories are supplied in wooden boxes. For proper and value preserving storage! Dividing attachment TA 250 For precision lathe PD 250/E,
More informationNote: This assembly instruction will cover all configurations of Alloy adjustable height double bases.
Note: This assembly instruction will cover all configurations of adjustable height double bases. 1 Screw in the provided adjustable glides into each leg as shown in Figure A. Two glides per leg. Figure
More informationGiraud Tool Company, Inc.
Motor Upgrade for Gracey Trimmer This package is intended to allow the user to upgrade their Gracey trimmer with a higher rpm motor and convenience features not found in the production offering. This upgrade
More informationM2 Assembly. M2 Sub-Assemblies mm Belt Sub-Assembly mm Belt Sub-Assembly Spider Sub-Assembly... 4
M2 Assembly Table of Contents M2 Sub-Assemblies... 3 630mm Belt Sub-Assembly... 3 702mm Belt Sub-Assembly... 3 Spider Sub-Assembly... 4 Idler Bolt Sub-Assembly... 8 Y Motor Sub-Assembly... 9 X Motor Sub-Assembly...
More informationMEFA mounting accessories
MEFA mounting accessories Mounting accessories Base plates Page 5/2 Double holder Page 5/4 Height-adjustable suspensions Page 5/5 Pendular bolt joints Page 5/6 Trapeze hanger Page 5/7 Threaded hooks, distance
More informationPlease read these Installation Instructions in their entirety prior to installing or operating this equipment.
2014-2017 Ram 2500 (All beds) Please read these in their entirety prior to installing or operating this equipment. This hitch is rated to 30,000 lbs. Gross Towing Weight and 7,500 lbs. Tongue Weight Bolt
More informationSECTION 7. SAFETYING
9/8/98 AC 43.13-1B SECTION 7. SAFETYING 7-122. GENERAL. The word safetying is a term universally used in the aircraft industry. Briefly, safetying is defined as: Securing by various means any nut, bolt,
More informationQuill Stop V2 Installation Guide 11/16/2014
Thank you for purchasing the Quill Stop for the Sieg X3 (Grizzly G0463) and SX3 (Grizzly G0619) mills. Your feedback is always appreciated. Please email questions and comments to gregpriest@cox.net. What
More informationBits for hand power tools
Bits for hand power tools Products Page Adaptors 232-233 nterchangeable boring bits 233 Boring bits 234~237 Mortise chisel & bit set 237 Plug cutters & ets 238-239 Forstner bits 240-241 Brad point bits
More informationMINI-LATHE QUICK CHANGE TOOL POST
MINI-LATHE QUICK CHANGE TOOL POST Cutting and assembly details Machinists should familiarize themselves with the contents of this section before jumping in to the drawings. Many details are described here
More informationZybach. sample. a mechanical clock. design by Derek Hugger. Important:
sample Important: McMaster Carr, a supplier whose part numbers are referenced throughout this document, can only ship within the United States. Builders outside of the U.S. must find an alternate supplier
More information25000 Series Lo-T TM Butterfly Control Valve Instructions
November 2001 25000 Series Lo-T TM Butterfly Control Valve Instructions Instruction No. 25.1:IM PRELIMINARY STEPS Before installation, note the flow direction arrow on the valve body. The flow should enter
More informationSTANDARD 430E Series. Bottom mounted full extension drawer runners 430E E E E E E E E E4000
STANDARD 430E Series Bottom mounted full extension drawer runners Specifications Runner 430E8000 430E7500 430E7000 430E6500 430E6000 430E5500 430E5000 430E4500 430E4000 430E3500 430E3000 430E2500 Nominal
More informationSE5a Wing Panels rev 1.0
SE5a Wing Panels rev 1.0 The top and bottom wings are different. They might look the same but the bottom wing has one less rib and some rib spacing difference. This is due to where the wooden interplane
More informationALL SEASON PATIO COVER
ALL SEASON PATIO COVER 61 Where the All Season Patio Cover is to be attached to the home, create a level line showing where the top of the mounting rail is to be located. Install each section with the
More informationROUTER BITS. Tooling Group Straight Bits. Insert Roundover Bits 2-7. Spiral Solid Carbide Bits. Insert Rabbeting Bits 2-8
ROUTER BITS Tooling Group 2 Straight Bits 2-2 Insert Roundover Bits 2-7 Spiral Solid Carbide Bits 2-3 Insert Rabbeting Bits 2-8 Insert Straigh Bits 1 flute 2-4 Dovetail Bits 2-9 Insert Plunging Straight
More informationLesson 22 Coupling Assembly (Video Lesson)
Lesson 22 Coupling Assembly (Video Lesson) Figure 22.1 Coupling Assembly OBJECTIVES Model the Shaft, Taper Coupling, and Straight Coupling components Use Assembly commands Apply Analysis to determine Global
More informationTrestle Table and Benches Materials List
Project 18444EZ: Trestle Table and Benches In the early days of our country, trestle tables were popular because they could easily be disassembled and moved out of the way when not in use no small advantage
More informationMachine Your Fishing Reel
Machine Your Fishing Reel You will be well prepared for the coming season if you start on this smooth-running job now. IF you're an enthusiastic fisherman and have a lathe in your workshop, we'll say no
More informationMM540 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS
MM50 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS Please read this entire manual before you begin. Do not unpack any contents until you verify all requirements on PAGE.
More informationGAGING AND INSPECTION
Fixture Plates...75 Fixturing Towers...76 CMM Fixturing Kits... 77-78 Clamping Components... 79-80 Standoffs and Locators... 81-82 Magnetic Components... 83-84 Height Adjustment...84 Positioners...85 Clamp
More informationAssembly & Construction Procedures
Assembly & Construction Procedures Foreword: This device was designed as an open source open architecture technology. With that in mind the construction of this device was made to be extremely flexible.
More informationRemoving the Z-Axis lead screw
Page 1 of 8 TITLE: Sabre Z-Axis Lead Screw Replacement Procedure Gerber FastFact #: 5048 Supplied by: Gerber Hardware Support Last Modified: June 14, 2007 Summary: Tools used: The following procedure explains
More informationLCD MONITOR/TV WALL MOUNT
INSTALLATION INSTRUCTIONS LCD MONITOR/TV WALL MOUNT DUAL DESK CLAMP (RFCD-110) S CAUTION CAUTION A alerts you to the possibility of serious injury or death if you do not follow the instructions. A CAUTION
More information