Power Vault Adapter. Install the Power Vault Adapter to MonoRail Power Feed Canopies & Recessed Can Transformer. Installation Instructions for
|
|
- Ann Newman
- 5 years ago
- Views:
Transcription
1 Installation Instructions for Power Vault Adapter 00MOPVLT_ 0MOVALT. SPECIAL INSTALLATION GENERAL PRODUCT I NFORMATION: This product is suitable for indoor dry locations only. This product is intended for use with Tech Lighting MonoRail system only. NOTE: This product must be used in concurrent with the MonoRail standoff vault adapter. Install the Power Vault Adapter to MonoRail Power Feed Canopies & Recessed Can Transformer A WIRE NUT B EXPOSED POST HOUSING Unscrew the housing from the housing nipple. Remove the wire nut from the center wire. Push the power vault adapter completely onto the exposed post and tighten the #- set screw with the / Allen wrench. Loosen (do not remove) the #- set screw on the housing nipple with the provided / Allen wrench. Pull out the housing nipple and the center wire out of the canopy. Pull out the center wire out of the housing nipple.
2 C E -/" ROD 0 D 0 Rotate the power vault adapter to ease feeding the center wire. F Feed the new center wire from the housing nipple and through the -/" rod or extension rod into one portion of the power vault adapter. Make sure that the contact is completely inside the housing nipple. EXTENDER ROD When power extender is not used in the system, push the -/" rod (provided with the power vault adapter) completely into the power vault adapter and tighten the #- set screw with the / Allen wrench. When power extender is used in the system, push the proper extender rod completely into the power vault adapter and tighten the #- set screw with the / Allen wrench. Push the housing nipple completely onto the -/" rod or the extender rod and tighten the #- set screw with the / Allen wrench. G Loop the center wire and feed it completely through the second portion of the power vault adapter into the canopy. PHILLIPS SCREW Ensure that the adapter is level and tighten the Phillips head screw.
3 Install the Power Vault Adapter to MonoRail Surface Transformers H A WIRE NUT.0 ALLEN SET SCREW BACKPLATE #- SETSCREW #-0 SCREW CENTER WIRE HOUSING DOME COVER I Tighten the set screw on the opposite side of the screw head with the provided.0 Allen wrench to ensure the position of the adapter. For the power feed canopies with dual posts repeat steps through for the other post. EXTENDER RODS Remove the #-0 screws with a Phillips screwdriver on the side of the transformer cover. Lift the dome cover off of the transformer housing. Disconnect the center wire from the circuit breaker wire by removing the wire nut. Unscrew the housing from the housing nipple. Loosen (do not remove) the #- set screw on the housing nipple with the / Allen wrench. Pull out the housing nipple and the center wire out of the canopy. Pull out the center wire out of the housing nipple. SEPARATOR B For the power feed canopies with dual posts, snap the extender rods together with the separators provided in the power extender package. Refer to the instruction provided with the power feed canopy to complete the installation. #- SET SCREW EXPOSED POST Push the power vault adapter completely onto the exposed post and tighten the #- set screw with the / Allen wrench.
4 C D -/" ROD 0 EXTENDER ROD When power extender is not used in the system, push the -/" rod (provided with the power vault adapter) completely into the power vault adapter and tighten the #- set screw with the / Allen wrench. 0 Push the housing nipple completely onto the -/" rod or the extender rod and tighten the #- set screw with the / Allen wrench. NOTE: The power extenders are precut for MonoRail power feed canopies. Power extenders must be cut to size when used with the surface mount transformers. Refer to the table below for the measurements. When power extender is used in the system, cut the extender rod to the proper length with a hack saw (use the table below). Clean the burrs in the cut section. Push the extender rod completely into the power vault adapter and tighten the #- set screw with the / Allen wrench. Push the housing nipple completely onto the extender rod and tighten the #- set screw with the / Allen wrench. Surface Mount Transformer Length for " Length for " Length for " Length for " Length for " Length for " Length for " SRT 0 N/A -/" -/" 0-/" -/" -/" -/" SRT 00 N/A -/" -/" -/" -/" -/" -/" SRT 00 N/A N/A -/" -/" 0-/" -/" 0-/"
5 E G PHILLIPS SCREW CENTER WIRE F Rotate the power vault adapter to ease feeding the center wire. Feed the new center wire from the housing nipple and through the -/" rod or extension rod into one portion of the power vault adapter. Make sure that the contact is completely inside the housing nipple. H Ensure that the adapter is level and tighten the Phillips head screw..0 ALLEN SET SCREW 0 Tighten the set screw on the opposite side of the screw head with the provided.0 Allen wrench to ensure the position of the adapter. Loop the center wire and feed it completely through the second portion of the power vault adapter into the dome cover and reconnect the wire with the wire nut. For the surface mount transformers with dual posts repeat steps through for the other post. For the surface mount transformers with dual posts repeat steps through for the other post.
6 Install the Power Vault Adaptor to Mini Surface Transformers I A EXTENDER RODS SEPARATOR For the surface mount transformers with dual posts, snap the extender rods together with the separators provided in the power extender package. Pull up the wire that leads through the center of the power feed. If the wire is embedded in the potting it is okay to pull the wire out of the potting material. Refer to the instruction provided with the surface mount transformer to complete the installation. Cut the center wire as close to the power feed as possible. B SET SCREW POWER FEED Loosen the set screw on the power feed. C CANOPY pull the power feed and wire from the canopy.
7 D F -/" ROD E Rotate the power vault adapter to ease feeding the center wire. Feed the new center wire from the housing nipple and through the -/" rod or extension rod into one portion of the power vault adapter. Make sure that the contact is completely inside the housing nipple. G EXTENDER ROD When power extender is not used in the system, push the -/" rod (provided with the power vault adapter) completely into the power vault adapter and tighten the #- set screw with the / Allen wrench. When power extender is used in the system, push the proper extender rod completely into the power vault adapter and tighten the #- set screw with the / Allen wrench. Push the housing nipple completely onto the -/" rod or the extender rod and tighten the #- set screw with the / Allen wrench. 0 0 Loop the center wire and feed it completely through the second portion of the power vault adapter into the canopy. Shortest Compatible Rigid Standoff Length for Length for Length for Length for Length for Length for Length for -/ -/ 0-/ -/ -/ -/ -/
8 H J WIRE CONNECTOR TRANSFORMER WIRE PHILLIPS SCREW CENTER WIRE Ensure that the adapter is level and tighten the Phillips head screw. Strip the end of the transformer wire. I Loosen ( Do Not Remove) the four set screws in the wire connector..0 ALLEN SET SCREW Push the transformer wire half way into the wire connector and tighten down the two set screws on that side. Push the center wire into the other half and tighten down the remaining two set screws. Follow the instructions provided with the mini surface transformer to complete the installation. Tighten the set screw on the opposite side of the screw head with the provided.0 Allen wrench to ensure the position of the adapter. SAVE THESE INSTRUCTIONS! 00 Linder Ave, Skokie, IL Tech Lighting, L.L.C. All rights reserved. The "Tech Lighting" graphic is a registered trademark of Tech Lighting, L.L.C. Tech Lighting reserves the right to change specifications for product improvements without notification. A Generation Brands Company
Micro Channel. Shorten the Fixture (optional) Installation Instructions for 700UMCD_ UNILUME. This product is suitable for damp locations.
Installation Instructions for Micro Channel 700UMCD_ 90MICRO. UNILUME GENERAL PRODUCT I NFORMATION: This product is suitable for damp locations. This product can be dimmed with a low-voltage electronic
More informationPrepare the Fixture. Sage 37 Bath. Back Plate Installation (Horizontal) Installation Instructions for 700BCSAGW37_
Installation Instructions for Sage Bath 00BCSAGW_ 90BCSAGEL.0 BATH COLLECTION GENERAL PRODUCT I NFORMATION: This fixture is intended to be installed utilizing NEC compliant junction boxes. This product
More informationMultiples EM_ 1.4. Install 1X1/1X2/1X3/1X4 Housings. Installation Instructions for. This product is suitable for indoor locations.
Installation Instructions for 90EMULTI Multiples EM_. GENERAL PRODUCT I NFORMATION: This product is suitable for indoor locations. This product can be dimmed with a standard electronic dimmer or a 0-0V
More informationRound or Square Type IC Down Light Housing with LED Lamp for Flangeless Trims E3_L_-L_DI 1.4
Installation Instructions for 90ELED-DIC Round or Square Type IC Down Light Housing with LED Lamp for Flangeless Trims E_L_-L_DI. LED - ROUND/ SQUARE FLANGELESS GENERAL PRODUCT I NFORMATION: This product
More informationInstall the Housing. Installation Instructions for Entra Round or Square Type IC, Air-tight New Construction Adjustable LED Housing EN3_-LH9_ 1.
Installation Instructions for Entra Round or Square Type IC, Air-tight New Construction Adjustable LED Housing 90ENTRA EN_-LH9_. LED - ROUND/ SQUARE GENERAL PRODUCT I NFORMATION: This product is safety
More informationRound or Square Chicago Plenum Down Light Housing with Lamp
Installation Instructions for 90ELED-DCP Round or Square Chicago Plenum Down Light Housing with Lamp LED E_-L_DC. LED - ROUND/ SQUARE GENERAL PRODUCT I NFORMATION: This product is suitable for indoor locations.
More informationInstallation Instructions for Zip Suspension Downlight with Remote Power and 4" Square or Round Canopy
Doc # 90-ZS-SQ_0 W. Fullerton Chicago, IL 0 Ph:.0.9 Fax:.9. www.pureedgelighting.com info@pureedgelighting.com 0 PureEdge Lighting. All Rights Reserved. Installation Instructions for Zip Suspension Downlight
More informationC 0.05" ALLEN WRENCH. Installation Instructions for Cirrus Channel Suspension T1 with 4" Square or Round Canopy. Section One: Adjusting Cable Position
Doc # 90-CST-SQ_0 W. Fullerton Chicago, IL 0 Ph:.0.9 Fax:.9. www.pureedgelighting.com info@pureedgelighting.com 0 PureEdge Lighting. All Rights Reserved. Installation Instructions for Cirrus Channel Suspension
More informationConnecting the Channel A
20 Edge Lighting. All Rights Reserved. Installation Instructions for Cirrus Channel Suspension T, Tubular Lens w/2sq or 2RD Canopy IMPORTANT INFORMATION - This product is suitable for indoor locations.
More informationmila-wall (Series100) General Operating Instructions page 1 of 15
mila-wall (Series100) General Operating Instructions page 1 of 15 Step #1: Before setting up walls, lower adjustable leveling feet on each panel approximately 1". This will allow access to the threaded
More informationInstallation Instructions for Cirrus Suspension Downlight with Power - End Feed. Section One: 4" Flush Canopy Version
Doc # 0-CSP-E_0 W. Fullerton Chicago, IL 606 Ph:.0. Fax:..6 www.pureedgelighting.com info@pureedgelighting.com 06 PureEdge Lighting. All Rights Reserved. Installation Instructions for Cirrus Suspension
More informationReflections Housing with EldoLED and Lutron Hi-lume Drivers EDIHE_ 1.4
Installation Instructions for 90EDIHE Reflections Housing with EldoLED and Lutron Hi-lume Drivers EDIHE_.4 LED GENERAL PRODUCT I NFORMATION: This product is suitable for indoor locations. This product
More informationRound or Square Type IC Wall Wash Housing with Lamp for Flangeless Trims
Installation Instructions for 90ELED-WIC Round or Square Type IC Wall Wash Housing with Lamp for Flangeless Trims LED E_L_-L_WI. LED - ROUND/ SQUARE FLANGELESS GENERAL PRODUCT I NFORMATION: This product
More informationInstallation Instructions for TruLine 1A Center Feed Power Channel Connector
IMPORTANT INFORMATION - This instruction must be used concurrently with other TruLine A BIY installation instructions. - This product is wall or ceiling mount. - This instruction shows a typical installation.
More informationLine volt rail & fixtures. Low volt quick connect fixtures with transformers
INSTRUCTIONS: Line Volt Flexrail2 Safety Instructions: A qualified electrician must install system only. System is intended for installation in accordance with National Electric Code, local and Federal
More informationA500 ASSEMBLY & INSTALLATION INSTRUCTIONS
ASSEMBLY & INSTALLATION INSTRUCTIONS 1 CONTENTS 2 Component Parts A B Canopy Mounting Plate C Cap (3) D Threaded Nipple E Threaded Standoffs (2) F Anchors (8) G #10 Screws (8) H Safety Cable (2) I Safety
More informationInstallation Instructions For TruLine 1.6A 24VDC
2014 Pure Lighting. All Rights Reserved. Installation Instructions For TruLine 1.6A 24VDC INS# 902-TL1.6A-07 1718 W. Fullerton Ave Chicago, IL 60614 Tel: 773-770-1195 Fax: 773-935-5613 www.purelighting.com
More informationHawko Zhaga Systems Installation Instructions
Hawko Zhaga Systems Installation Instructions Contents Wire Suspension Installation 4 Recessed Brackets 6 Fixed Suspension Rods 8 Swivel Suspension Rods 10 Surface Mount Ceiling 12 Surface Mount Wall
More informationReplacing a Wheel on the Pinch Wheel assembly
14140 NE 200th St - Woodinville, WA. 98072 - PH: (425) 398-8282 - Fax: (425) 398-8383 Replacing a Wheel on the Pinch Wheel assembly Determine which pinch wheel assembly your plotter or cutter has. See
More informationwith Lamp Install the Housing with Adjustable Bars Installation Instructions for LED E3_-L_DN 1.1 ½ to ¾ ¾ or thicker
Installation Instructions for 90ELED-D Round or Square Type IC, Non-IC Down Light Housing with Lamp LED E_-L_DN. LED - ROUND/ SQUARE GENERAL PRODUCT I NFORMATION: This product is suitable for indoor locations.
More informationInstallation Instructions for DIY or Completed 45 Degree Light Channel
201 Edge Lighting. All Rights Reserved. Installation Instructions for DIY or Completed Degree Light Channel IMPORTANT INFORMATION - This instruction shows a typical installation. 11 W. Fullerton Ave Chicago,
More informationReplacing the PCM Instruction Sheet
Replacing the PCM Instruction Sheet INTRODUCTION Use the following instructions when replacing or upgrading a Processor Control Module (PCM) in CP2000-ZX and CP2000-M/MR projectors. The entire procedure
More informationInstallation Instructions for DIY or Completed Light Channel.6 Millwork
2017 Edge Lighting. All Rights Reserved. 1718 W. Fullerton Ave Chicago, IL 60614 Tel: 77-770-1195 Fax: 77-95-561 www.edgelighting.com info@edgelighting.com LCMW.6- - - 904-LCMW.6_02 Installation Instructions
More informationEPPA2-KIT DUAL MONITOR ARM CONVERSION
EPPA2-KIT DUAL MONITOR ARM CONVERSION EPPA2-KIT Rev A 10/17 Model EPPA2-KIT-XXX ASSEMBLY AND ADJUSTMENT EPPA2-KIT PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the assembly and adjustment
More information100mm (3in) Slide Stop Cut to 6mm (1/4in) Sections. Quantity: mm (10in) Skewers Quanity: 10. Material to Lift. Material for Blades.
Wind Lift Page 1 The Activity This guide will take you through the process of creating a wind powered lift. You ll start by creating the stand. The lift mechanism, hub and blades are then added. Before
More informationIMPORTANT SAFETY INSTRUCTIONS:
Online: www.ballarddesigns.com PRODUCT NAME: MR Geometric Chandelier ITEM NUMBER: LC971 DIMENSIONS OF ITEM ASSEMBLED: FLUSH- 36 H x 42 W x 30 1/2 D HANGING- 96 H x 42 W x 30 1/2 D HANGING FIXTURE: FLUSH
More informationSCC Inc. VA Series. Technical Instructions. Document No. VA-7000 February 1, VA Valve Actuator Assemblies with VRG Butterfly Valves.
February 1, 2016 VA Valve Actuator Assemblies with VRG Butterfly Valves Description Features Application VA valve actuator assemblies include a Siemens SQM actuator reliably mounted to a VRG butterfly
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationPARTS & ASSEMBLY SHEET
PARTS & ASSEMBLY SHEET Fixture Name: Echelon 8981-3P BRI / GRM This fixture assembled PO: Date: Notice: Please review the parts listing and check for all parts before assembling the fixture. If any parts
More informationElimination of Elevator Bounce
For the Agilent Archon Autosampler Rework Instructions CAUTION This kit is intended for use by Agilent Service personnel only. Elevator Removal 1 Open top cover. 2 Open front lower door. 3 Remove vial
More informationGiraud Tool Company, Inc.
Motor Upgrade for Gracey Trimmer This package is intended to allow the user to upgrade their Gracey trimmer with a higher rpm motor and convenience features not found in the production offering. This upgrade
More informationJenny Legs Assembly Instructions
Jenny Legs Assembly Instructions R EXTENDED PHILLIPS BIT MM ALLEN WRENCH 6MM HEX DRIVE /" 007 Steelcase Inc. Grand Rapids, MI 90 U.S.A. Printed in U.S.A. Page of 6 88000 Rev F Jenny Club Instructions:
More informationMotorized or Crank Operated Fortress Zipper Track Shade with Housing and Side Track Installation Instructions
Motorized or Crank Operated Fortress Zipper Track Shade with Housing and Side Track Installation Instructions Tools Needed Drill 3/8 Metal Drill Bit ¼ Masonry Drill Bit Measuring Tape Pencil 4 Level Phillips
More informationAUTOMATIC ADVANCE MANUAL
AUTOMATIC ADVANCE MANUAL AVL Looms, Inc. 3851 Morrow Lane, Suite #9 Chico, CA 95928-8305 530 893-4915 530 893-1372 fax # info@avlusa.com www.avlusa.com Copyright 2009 TABLE OF CONTENTS Page # I. Parts.........................
More informationIMPORTANT SAFETY INSTRUCTIONS:
PRODUCT NAME: DELANEY PENDANT ITEM NUMBER: LC661 DIMENSIONS OF ITEM ASSEMBLED: 20 3/4 H x 10 1/2 Square IMPORTANT SAFETY INSTRUCTIONS: -We strongly recommend that a professional electrician install all
More informationStep 1 Remove Focus Knob
Installation Instructions Celestron 14 Edge HD Telescopes Important: The telescope optical tube must be positioned horizontally before removing the original focus assembly. If the telescope is not horizontal
More informationSALEM ICE CABIN 80A MINI-BREAKER INSTALLATION
Introduction Some Ice (House) Cabin trailers may operate slowly and/or stop operating after five seconds of use. The cause is the main power for the dual polarity solenoid, which is supplied by a 10AWG
More informationSignal Mirror Installation Instructions
Signal Mirror Installation Instructions 2006 2007 Honda Ridgeline THE safety accessory of the 21 st Century. P/N 210 0142 0 Rev. A (9/5/07), BTV 2007 Muth Company, LLC Professional Installation Recommended:
More informationBi-Color Signal Mirror Installation Instructions
Bi-Color Signal Mirror Installation Instructions 2005-2009 Toyota Tacoma THE safety accessory of the 21 st Century. P/N 210-0141-0 Rev. A2 (3/30/09), BTV 2007 Muth Mirror Systems, LLC Page 3 of 13PplPage
More informationWhite Quail Auto Trap
White Quail Auto Trap WARNING SAFETY, STORAGE & USE IF THE MAIN SPRING IS ATTACHED AND THE TRAP ARM IS IN THE 6 O CLOCK POSITION, THE TRAP IS ARMED AND EXTREME CAUTION IS REQUIRED. TO DISARM, TURN THE
More informationInstallation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens
Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be
More informationEraser Conveyor Belt Cleaning System IWARNING Always obey all applicable safety rules. Be sure all power to the conveyor has been disconnected and con
INSTALLATION GUIDE LIB-CP-REA-03-01 Rev. 10 Eraser Conveyor Belt Cleaning System ARGONICS Eraser Conveyor Belt Cleaning System IWARNING Always obey all applicable safety rules. Be sure all power to the
More informationPARTS & ASSEMBLY SHEET
PARTS & ASSEMBLY SHEET Fixture Name: Echelon 8981-9 BRI / GRM This fixture assembled PO: Date: Notice: Please review the parts listing and check for all parts before assembling the fixture. If any parts
More informationTransform your space into an extraordinarily inviting home, office or gathering place with the versatile, powerful and elegant Olin Fixture system.
OLIN FIXTURES Transform your space into an extraordinarily inviting home, office or gathering place with the versatile, powerful and elegant Olin Fixture system. This new Trulux collection introduces
More informationKX2 Side KX installation
KX2 Side KX installation NOTE: The installation of any Side KX parts does NOT require the unsoldering of any connection nor removal of ANY of the boards from within the radio! The user/installer assumes
More informationSeriesTWO RGB Fluorescent Fixtures. Installation and Instruction Manual
SeriesTWO RGB Fluorescent Fixtures Installation and Instruction Manual Brightline LP 580 Mayer Street #7, Bridgeville PA 15017 Phone 1-412-206-0106 Fax 1-412-206-0146 www.brightlines.com The Brightline
More informationArched Top Lantern Pendant Assembly and Installation Instructions. Country of Destination: US/CN UK/EU/AUS Middle East
CAUTION: Arched Top Lantern Pendant Assembly and Installation Instructions Country of Destination: US/CN UK/EU/AUS Middle East BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF
More informationElite Series Fender Flares
Page 1 of 8 Installation Instructions I - Sheet Number I606RPG Rev.B Important Safety Information Tools Required Contents Elite Series Fender Flares Preparation Before Painting / Installation NOTE Actual
More informationArc Trainer Main Frame Assembly
Arc Trainer Main Frame Assembly Kit No. 610AK019-4 Kit No. 630AK019-4 NOTE: This instruction sheet describes how to replace the main frame assembly in the Arc Trainer 610A. Tools Required 3/16 Allen wrench
More informationFilm Scanner 24V Inverter Replacement
Overview Please read and understand the entire work instruction before beginning any procedures. WARNING: icrco assumes no liability for damage done to the unit while following these instructions. These
More informationInstruction page index: Installation Instructions for Bosca Models BOS-XX-C-XX, & BOS-XX-S-XX. Page 1 of 5
Installation Instructions for Bosca Models BOS-XX-C-XX, & BOS-XX-S-XX Page of 5 BOSCA clip-in mount or BOSCA magnetic BOSCA -in mount Instruction page index: Clip-in installation Screw-in installation
More informationFlat Panel Mobile Cart and Accessories
INSTALLATION MANUAL Flat Panel Mobile Cart and Accessories Optional Accessories TCH01 TDV01 TLP01 TCR01 Note: The accessories are not standard. The accessories will be selected according to user requirement.
More informationPower Break II Circuit Breakers
DEH40466 Installation Instructions R05 Power Break II Circuit Breakers Replacement Stop Block Kit Application This kit is provided to replace the stop block assembly in the Power Break II insulated-case
More informationReplacing the Reciprocator on an SWF Multi-head.
Replacing the Reciprocator on an SWF Multi-head. Follow the instructions below to replace the reciprocator in the SWF multi-head machines. The tools required are found in the tool kit that came with the
More informationInstallation Manual MODEL E-42
Installation Manual MODEL E-42 GET TO KNOW YOUR UNIT 2 (BOTTOM OF RACEWAY) 1 3 1. CROSS BRACES 2. ELECTRICAL RACEWAY 3. ELECTRICAL OUTLET - Stud Finder - 12-14 Level - Tape Measure - Small Flathead Screwdriver
More informationHatchback Wing Riser Kit
Hatchback Wing Riser Kit 2015-06-11 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation of aftermarket
More informationi f c o L INC. COMPLETE MOTORIZED GLIDE OUT ADJUSTMENTS PROCEDURE MANUAL #400011
i f c o L INC. 24076 Reedy Dr. Elkhart, IN 46514 (574)-266-5551 (Office) (574)-206-9296 (Fax) COMPLETE MOTORIZED GLIDE OUT ADJUSTMENTS PROCEDURE MANUAL #400011 The following procedures are used to acquire
More informationInde-Pendants Family. 32L Ring Plaster Trim, Grid and Drywall Ceiling Types. Document No Installation instructions for 32L-Rxx-P
Inde-Pendants Family 32L Ring Plaster Trim, Grid and Drywall Ceiling Types Installation instructions for 32L-Rxx-P Document No. Supplied by Litecontrol 32L Inde-Pendants: Ring (Plaster Trim, Grid and Drywall
More informationQueen Wingback Bed King Wingback Bed
Parts and Hardware List A. Side Rails with Attachment Hooks 2 pcs B. Foot Rail 1 pc C. Head Rail 1 pc D. Center Support Slat 1 pc E. Leg Supports 3 pcs F. Support Slats 4 pcs G. Flat Washers 8 pcs H. Lock
More informationMOTORIZED STANDARD SHADE WITH CABLES Installation Instructions
Tools Needed Drill Measuring Tape Pencil 2 Level Plumb Line ¼ Masonry Drill Bit Hammer Linesmans Pliers Cable Cutters Phillips & Flat-Head Screw Driver 11/32 Socket or Open End Wrench 5/32 Allen Wrench
More informationMANUAL e130. Wallstation
MANUAL 07.29.13 e130 Wallstation The Enovate Medical e130 Wallstation was designed to set a new standard in quality. Enovate Medical s goal is to provide a wallstation that is ready for years of use,
More informationBL-ER-P Ethernet Radio Unit for Pedestal Installation Guide
Assemble the Antenna Riser 1. Remove the antenna riser assembly and the antenna from its packaging. 2. Remove the plastic cap, the nut, and the lock washer from the stem of the antenna. 3. Put the stem
More informationInstallation and Assembly: 32" - 60" Flat Panel TV Cart
Installation and Assembly: 32" - 60" Flat Panel TV Cart Models: SR1G, SR560G R This product is U isted. It must be installed by a qualified professional installer. Max U oad Capacity: 150 lb (68 kg) screen
More informationINSTALLATION INSTRUCTION Solorail - Low Voltage Starter Kit
IMPORTANT SAFETY INSTRUCTIONS: Read all instructions. Turn off power at main switch before installing or modifying the system. Do not install the system: - Within six inches of any curtain or combustible
More informationRAIL 4 PERIMETER RP4D RECESSED T-BAR LED TELESCOPIC, INTEGRAL DRIVER
INSTALLATION INSTRUCTIONS RAIL 4 PERIMETER RP4D RECESSED T-BAR LED TELESCOPIC, INTEGRAL DRIVER NOTE: The following instructions provide general guidelines for product installation. For additional information
More informationAssembly Instructions
1 27694 Trend Podium Assembly Instructions #27694 Trend Podium Part Drawing Description Qty Part Drawing Description Qty P-1 Base 1 EA Hardware List Screw M6x12mm 30 EA P-2 Right Side Panel 1 EA A2 Phil
More informationSignature Choral Riser Side Rail
Assembly/Owner s Manual Signature Choral Riser Side Rail Signature Choral 3-Step Riser with Optional Side Rail Signature Choral 4-Step Riser with Optional Side Rail CONTENTS Visit the Signature Choral
More informationHow to install/ remove faceplate and hand brakes onto lathes Date Raised: 22 March 2017
Teknatool International Limited 7D Dallan Place, Rosedale, Auckland, New Zealand Tel: +64 09 477 5600 Fax: +64 477 5601 Email: service@teknatool.com Website: www.teknatool.com Frequently Asked Questions
More informationInstallation Instructions For Reveal
2017 Pure Lighting. All Rights Reserved. Installation Instructions For Reveal IS# 902-RV-24VDC-07 1718 W. Fullerton Ave Chicago, IL 60614 Tel: 773-770-1196 Fax: 773-883-6128 www.purelighting.com info@purelighting.com
More informationTS- Feedback Sweep Motor Error
Step Description Picture Machine gives the message Feedback Sweep Motor upon start up. During gameplay the machine stopped and said Feedback Sweep Motor. Reasons for this message could be: 1. There is
More informationTOYOTA COROLLA EC REARVIEW MIRROR Section I Installation Preparation
Section I Installation Preparation Part Number: PT374-02030 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly w/compass & Maplights 2 1 Hardware Bag
More informationMobile Gain Antennas MHz Models RRA-4935/RRA-4936
890-960 MHz Models RRA-4935/RRA-4936 Installation See Table 1 for recommended antenna location for various vehicles. The installation procedure which follows is for a typical passenger car. The procedure
More informationSignal Mirror Installation Instructions Toyota Tacoma
Signal Mirror Installation Instructions 2005-2015 Toyota Tacoma THE safety accessory of the 21 st Century. P/N 210-0115-0 Rev. A4 (3/11/15), BTV 2005 Muth Mirror Systems, LLC Page 3 of 12PplPage 3 of 12
More informationOperation Manual Panel Mounting Gas Pressure Regulators
687 Technology Way Napa, CA 94558 Phone: (707) 259-0102 FAX: (707) 259-0117 www.aptech-online.com Table of Contents: A. General information... 1 B. Panel Mount Nut - AP/AZ/AK/SL Model Regulators... 1 C.
More informationRemoving and Replacing the Y-truck
Service Documentation Removing and Replacing the Y-truck To remove and replace the Y-truck you will need the following tools: 4mm Allen wrench 12mm stamped flat wrench #2 Phillips screwdriver (magnetic
More informationRepair Instructions. Replacing and Installing a Sweep Motor. Elite Models that Apply: Phenom 1 & 2. Step Description Tools Picture
Elite Models that Apply: Phenom 1 & 2 Step Description Tools Picture Disconnecting The Phenom Hopper Unit and Base Unit. 1 Step 1.) Unscrew the 4 wing screws (D) and washers (C) from the bottom of the
More informationPORTA~TRACE. GAGNE, INC. 41 Commercial Dr. Johnson City, New York Phone: Fax: ASSEMBLY INSTRUCTIONS
PORTA~TRACE GAGNE, INC. 41 Commercial Dr. Johnson City, New York 13790 Phone: 1-607-729-3366 Fax: 1-607-729-7644 ASSEMBLY INSTRUCTIONS PORTA~TRACE MODEL 2436T LIGHT TABLE PORTA~TRACE MODEL 3648T LIGHT
More informationB B B
Winchester SXP Gauge Tactlite Six Position Adjustable Shotgun Stock with Scorpion Recoil System B..0.00 B..0.00 B..0.00 Removable/Adjustable Tactical Cheekrests X Scorpion Recoil Pad Dual Sided QD Attachment
More informationTBX-68S Isothermal Terminal Block
INSTALLATION GUIDE TBX-68S Isothermal Terminal Block Contents Introduction This installation guide describes how to install and connect signals to the TBX-68S isothermal terminal block for use with the
More informationCOWO. Customer Wall Outlet. 1 General. 2 Kit content. 3 Handling of the box. TC-1203-IP Rev A, Apr
COWO I N S T A L L A T I O N I N S T R U C T I O N TC-1203-IP Rev A, Apr 2017 www.commscope.com Customer Wall Outlet 1 General Customer Wall Outlet 2 Fiber for max. 2 bend reduced fibers, 2 SC-adapters
More informationInstallation Manual MODEL AE-46
Installation Manual MODEL AE-46 GET TO KNOW YOUR UNIT (BOTTOM OF RACEWAY) 2 5 1 4 6 3 1. CROSS BRACES 2. ELECTRICAL RACEWAY 3. SIDE BRACKETS 4. ELECTRICAL CORD COVER 5. ELECTRICAL OUTLET 6. HOT IRON REST
More informationInstallation Instructions for TruLine 1.6A 24VDC. Section One: Basic Configuration Options
Doc # 902-TL1.6A_07 1718 W. Fullerton Chicago, IL 60614 Ph: 773.770.1195 Fax: 773.935.5613 www.pureedgelighting.com info@pureedgelighting.com 2016 PureEdge Lighting. All Rights Reserved. Installation Instructions
More informationINS TRUC T I ON M A NU A L
INS TRUC T I ON M A NU A L Packing list: 1: PP F6F fuselage *1 2: Carbon tube 5*5*940mm *1 3: Pull rod *4 4: Motor mount *1 5: Quick rod adjuster *4 6: Hinge *4 7: M3 screws *4 8: Hook and loop tape *1
More information6MM ALLEN KEY FOR ROOF CLIPS PHILLIPS HEAD BIT FOR SCREWS FOR DOOR FRAME SPIRIT/LASER LEVEL TO LEVEL THE UNIT
1 TOOLS REQUIRED: MOVING CART/DOLLY FOR TRANSPORTING PANELS, ROOF, AND POSTS TWO 9 FT. STEP LADDERS FOR INSTALLING ROOF & PANELS MINI REVERSIBLE RATCHET 1/4 DRIVE FOR CORNER SCREWS ON TOP TRAVERSE BEAMS
More informationBLUEMOTION UXP, CDP, SD
Feed and Support Kit Contents FEED KIT CONTENTS: - One () 7 Feed Cord - One () 4 Canopy - One () Grommet - One () Threaded Barrel - One () 7 Swedged Suspension Cable - One () Y-Cable Assembly with Cable
More informationAssembly Instructions and Owner s Manual Flex TechBridge
Assembly Instructions and Owner s Manual Flex TechBridge Contents Important User Information...........................2 Safety Precautions.................................2 Required Tools.....................................3
More informationInstalling the Partridge RA Extension on Losmandy G11
Installing the Partridge RA Extension on Losmandy G11 Michael Herman July 20, 2015 Tools: 3/16 inch hex key (allen wrench) [If desired for DEC indicator ring friction improvement: flat screwdriver, and
More informationELECTRIC RACER BASIC BUILD
Page 1 Name: Set: Date: This guide will take you through the process of creating a basic electric racer. After you finish this build, you should be able to experiment, design and engineer your own racer.
More informationOpen Air. Kit includes: Drawer Full Indicator board assembly, (2) retainers, and (4) screws. PREPARATION
Open Air Installation Video You will need: 8-inch #2 Phillips screwdriver Needle-nose pliers DFI INSTALLATION GUIDE For installation videos, visit the Customer Service playlist at www.youtube.com/user/thelitterrobot
More informationTurn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
Quoizel, Inc. 6 Corporate Parkway Goose Creek, SC Customer Service Phone 631.273.2700 Fax 631.231.7102 www.quoizel. Pleasegotowww.quoizel.forproductcleaningtips.GototheCare+Maintenance selection. ToolsRequired:Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wire
More informationInstallation and Assembly: 32" - 60" Flat Panel TV Cart
nstallation and Assembly: 32" - 60" Flat Panel TV Cart Models: SR1M, SR560M R This product is UL Listed. t must be installed by a qualified professional installer. Max UL Load Capacity: 150 lb (68 kg)
More informationInstallation and Assembly: In-wall Mount for 32" to 71" Flat Panel Displays
Installation and Assembly: In-wall Mount for 32" to 71" Flat Panel Displays Model# Display size range IM760P, IM760P-S 32" to 71" (81 to 180 cm) IM760PU, IM760PU-S 32" to 65" (81 to 165 cm) This product
More informationWater Level Meter: Op Instructions
Equipment Check 1. Turn sensitivity switch fully clockwise. Notes: 1. Clockwise rotation of sensitivity swsitch turns meter on and increases sensitivity. 2. Always set switch to highest sensitivity position,
More informationArchitectural Supports
Architectural Supports www.zip-clip.com 1 Zip-Clip - A Global Brand Copyright of Zip-Clip Ltd 2016 All descriptions and illustrations in this manual are intended for guidance purposes only. Zip-Clip Ltd
More informationTM12 ASSEMBLY INSTRUCTIONS
TM12 ASSEMBLY INSTRUCTIONS Congratulations on purchasing the finest purple martin house available. Nature House Brand houses are the proven leader in aluminum martin housing for over half a century. After
More informationSOCCER TABLE. Assembly Instructions
Updated: 5/4/16 SOCCER TABLE Assembly Instructions Table of Contents Parts Identifier... 3 Hardware Identifier. 4 Table Assembly Instructions... 5 Table Assembly Pictures..... 6, 7, 8 2 Page Parts Identifier
More informationRepair Instructions grand MA
Repair Instructions grand MA Grand MA 1 Repair Instructions grand MA The following tasks may be performed by qualified personnel only! By disregarding the instructions or the prescribed sequence of tasks
More informationSignal Mirror Installation Instructions
Signal Mirror Installation Instructions 2004 2008 Ford F-150 XLT, FX4, & Lariat Pre-wired without side signals Pre-wired with side signals Without side directional lights, see page 2 With side directional
More informationB B B
Stock with Scorpion Recoil Pad B..0.0 B..0.0 B..0.0 Removable/Adjustable Tactical Cheekrests X Scorpion Recoil Pad Dual Sided QD Attachment Point Six Position Adjustable Stock Slim Line Rear Aluminum Receiver
More informationPatton Robotics ESRA II Expressive System for Robotic Animation
Patton Robotics ESRA II Expressive System for Robotic Animation Assembly and Operation Instructions Version 1.0 Patton Robotics, LLC. 61 Hagan Drive New Hope, PA 18938 Copyright 2015 Patton Robotics, LLC.
More information