SCRAPING. Why and How. By Ron Gerlach For SCHSM
|
|
- Clare Walker
- 6 years ago
- Views:
Transcription
1 SCRAPING Why and How By Ron Gerlach For SCHSM
2 Why Scrape? Elegantly simple technique that provides results that are difficult to match Still used today on high end machines to fit sliding members to way surfaces Scraped surfaces retain oil in the fine scrape marks in a way that ground surfaces cannot A must, on large new and rebuilt machine tools Take the tool to the work A straight edge can be a fraction of the weight of the tool Inexpensive Tools
3 Example, Finely Scraped Straight Edge
4 Reflection off of a fine scraped surface
5 Machine Tool Rebuilding Any slide way surface Precision mating surfaces Applications Easy way to true up two mating surfaces if a surface grinder is not available or practical Cylinder head to block Bearing block halves Flattening parts that are impractical to clamp or hold for milling Quick way to accurately correct damage to flat surfaces Dings Edge Impacts Gouges
6 Basic Procedure for Scraping Start with a known flat surface Surface plate Ground bed way Apply a spotting compound to flat reference surface Apply work piece surface to be scraped to the inked/dyed surface (or vice versa) and move slightly back and forth Separate and observe spots transferred to work piece Scrape off metal from any locations with spots Repeat until spotting produces a uniformly distributed set of spots through out the work piece surface
7 Flat Plate, Early Stage
8 Flat Plate, After Several Cycles
9 Flat Plate After More Cycles
10 Lathe Cross Slide, Early Stage
11 Lathe Cross Slide, Later Stage
12 Types of Surfaces to be Scraped Any flat surface Size constrained by size of reference surface or straight edge Long surfaces can be successfully scraped with a shorter straight edge Requires careful attention to spotting indications Start at one end and scrape until level Progress towards opposite end while overlapping portion of previous section Scrape new section until contact on previous section is restored Metals as well as some specialty plastics such as Rulon and Turcite Dovetails Usually requires some method to measure distance between opposing dovetails Precision ground rod in dovetail opening provides an easy and repeatable measurement point
13 Challenges, Spotting Spotting Compound Application Heavier during initial aggressive scraping Lighter and thinner as surface progresses closer to final condition Accurate Spotting Consistent and even application of compound Consistent and even application of pressure between work piece and reference surface Gravity is always best when possible, can be augmented with weights Must be aware of how center of gravity acts on work or straight edge Manually applied pressure can work but must be consistent Reading the spots For heavy scraping; if its blue, scrape it For light scraping; scrape light areas surrounded by blue
14 Fine Spotting
15 Challenges, Scraping Basic technique is to apply pushing & downward force on scrapers Careful scraping Avoid gouges by controlling scraper angle and pressure Developing an ability to scrape with required aggressiveness Heavy metal removal when surface is far from desired flatness Light metal removal when surface is close to desired flatness Avoid damage to edges Patience The results can be slow but the reward is worth it
16 Control Scraping Straight Down removes metal in a homogenous manner anywhere across entire surface Work piece progresses as angle remains fixed as surface becomes True Techniques can be applied to actually tilt or skew a surface as need Two surfaces on different planes can be worked to be parallel Commonly done when working with dovetails and flat ways to compensate for uneven wear Leaving one end un-scraped while continuing to spot and scrape all other sections will rotate work piece down from the unscraped edge or point
17 Tools Needed Flat Reference Surface plate Straight Edge Spotting Compound Prussian Blue Water based Compound, Canode #2243 from Dapra Almost any substance that will leave a fine film and that will transfer Lipstick Paint pigment Ink Roller Scrapers Carbide (best over all) Commercial units available Inexpensive inserts can be brazed to handles and sharpened as required Old files (will work but requires frequent sharpening)
18 Tools, Continued Clean flat file to debur surface before each spotting More critical when doing heavy metal removal Paint brush to clean away scraping residue Sturdy holding device Keep work piece from moving when applying heavy scraping action Flexibility to move work piece around for best light and tool access Gloves
19 Camel Back Straight Edge
20 SCRAPERS
21 More Commercial Hand Scrapers
22 Home Made HandScrapers
23 Scraping Links Yahoo Groups-Scraping Wikipedia-Hand Scraping Straight Talk on Ways: Andrew Devitt, Devitt Machinery Turcite: Machine Tool Specialty Components BIAX Scrapers: Dapra Corporation Practical Machinist Machine Repair: books, videos, tools Machine Tool Reconditioning by Edward Connelly
Ball-Joint Scrapers Steel Blade Carbide Blade 05K K21.04
Ball-Joint Scrapers Steel Blade Carbide Blade 05K21.01 05K21.04 The Veritas Ball-Joint Scraper is based on a tool originally made by L.S. Starrett Tool Company but out of production for many years. Originally
More informationBEARING AND TYPES OF BEARING
BEARING AND TYPES OF BEARING In this article, you will learn about bearing and types of bearing. Generally, all types of machinery are provided with supports for rotating shafts, the supporting device
More informationTravis Bishop. Submitted to: Dr. John Davis. Date: 3 December Course: ETME 310 Section: 004. Lab Topic: Milling Project (Vise)
Travis Bishop Submitted to: Dr. John Davis Date: 3 December 2012 Course: ETME 310 Section: 004 Lab Topic: Milling Project (Vise) Introduction: Purpose of Experiment: This experiment was conducted to teach
More informationInstructables Butcher Block Top
Instructables Butcher Block Top Project Overview: This project requires basic woodworking skills and access to woodworking machines. Woodworking machines have sharp cutting edges and are NOT forgiving.
More informationPower Poles. Interoperability -- Why Anderson Powerpoles??
Interoperability -- Why Anderson Powerpoles?? Power Poles In the rather frantic and hectic long days and nights of amateur radio emergency operations in the immediate aftermath of the September 2001 World
More informationHow to use the Derry Tools Burnisher
How to use the Derry Tools Burnisher Thank you for your interest in the Derry Tools Burnisher. Burnishing a shear scrapers edge is a simple process by which pressure is applied to an already sharpened
More informationAgricultural Mechanics and Technology Power Tool Safety Rules
Agricultural Mechanics and Technology Power Tool Safety Rules Name: BAND SAW Use: Cutting curves, circles and irregular shapes. 1. Use clean SHARP blades. 2. The teeth should always point DOWN. 3. Adjust
More informationROOP LAL Unit-6 Shaper & Planer Mechanical Engineering Department
Notes: shapers and planers Basic Mechanical Engineering (Part B ) 1 Introduction: Both shapers and planers are machine tools which produce a flat surface. They are capable of machining a horizontal, vertical
More informationTool Rest SVD-110 (60483) Positioning of Machine
Tool Rest SVD-110 (60483) TURNING SCRAPERS Round nose Square end Curved CARVING SCORPS AND INSHAVES CABINET SCRAPERS HOLLOWING TOOLS SCREW DRIVERS Positioning of Machine Grinding direction: away from or
More information1951 SB 9 x 4 ½ Model A. Originally sold to a tool and die shop In Leominster.
1951 SB 9 x 4 ½ Model A Originally sold to a tool and die shop In Leominster. It then spent 30 years in a auto repair shop cutting commutators on Truck generators pretty grungy.. Stuff!. FIRST THING stevewb
More informationAvoiding Common Problems in Saw Preparation
Avoiding Common Problems in Saw Preparation Bruce Lehmann, P.Eng, Ph.D. This talk draws on the expertise of experienced sawfilers, and some research results to show practical techniques and possible problems
More informationREEL BLADE / BED KNIFE ADJUSTING & SHARPENING
Here s a QR code image that can be used to access this document on a portable device. Reel Mower Cutting Fundamentals The reel mower s cutting ability is the result of the corner edges of the reel blade
More informationPRECISION KNIFE SHARPENING SYSTEM USER MANUAL
PRECISION KNIFE SHARPENING SYSTEM USER MANUAL * Knife not included Thank you for purchasing FINO EDGE Precision Knife Sharpening System! A C F J I E B D G H մbox Contents A Heavy-Duty Base Plate with 3
More informationINSTALLATION OF WELLS SUPER QUICK CHUCK LEFT HAND ON RED WING LATHE
DENTAL, INC. TECHNICAL BULLETIN Q824-022510 5860 FLYNN CREEK ROAD READ ALL INSTRUCTIONS P.O. BOX 106 BEFORE PROCEEDING COMPTCHE, CALIFORNIA, U.S.A. 95427 SAVE THIS FOR FUTURE REFERENCE www.wellsdental.com
More informationSurface planer or buzzer. Performs the tasks of dressing, squaring and straightening timber Machining short lengths of timber. Without the bridge guard. Without the appropriate training. Without PPE. Set
More informationKey Message It s hard to achieve results on the hill if you don t look after your equipment. Practice, Practice, Practice There s more than one way to
Ski Tuning Basics Key Message It s hard to achieve results on the hill if you don t look after your equipment. Practice, Practice, Practice There s more than one way to do it Teach, Guide and Supervise
More informationBoom Adjustment Instructions
P.O. Box 368, 123 Pickle Row, Wautoma, WI 54982 Phone: (920) 787-7010 Fax: (920) 787-7030 www.specialtyspraybooms.com Boom Adjustment Instructions Note: Call service line at 920.240.5218 with questions
More informationCHAPTER 52 ELECTRICAL POWER TOOLS
CHAPTER 52 ELECTRICAL POWER TOOLS HOW TO CHOOSE AND USE THEM The Types and Uses pages provide you with a list of the electrical power tools found in the pioneer tool outfit. These pages should help you
More informationFlute Station Post Raising Wrench
1. Carefully examine all the tone holes for flatness. This must be don t with a precision flatness gauge such as our 227051 Lighted Tone Hole Gauge. 2. Carefully mark or map the low spots. This can be
More informationCabinet Scraper 05P32.05
Cabinet Scraper 05P32.05 The Veritas Cabinet Scraper is a very versatile tool, capable of both rough and fine work. As supplied, both edges of the blade are ground at 45 and need only burnishing for rough
More informationTurning an End Grain Lidded Box
Turning an End Grain Lidded Box by Michael Stafford Copyright 2006 All Rights Reserved 1 Turning an End Grain Lidded Box Turning an end grain lidded box differs from face grain bowl turning primarily in
More informationVicmarc Grinding System
Vicmarc Grinding System User Manual Vicmarc Sharpening Jig Part No. V00437 Vicmarc Grinding Rest Part No. V00438 Vicmarc Machinery Pty Ltd Manufacturer of Quality Woodturning Lathes and Accessories Vicmarc
More informationCaution: Always use safety glasses or a full face shield when turning anything on a lathe.
May 26, 2009 Making a 6 Peppermill Page 1 Acknowledgment is given to Jackie Johnson from Nashville, TN for providing the original instructions and method for this article. The design of this mill can be
More information10/24/2011. Chapter 3
Chapter 3 Exact alignment Availability to compensate wear Minimum friction Ease of assembly and economy of manufacture Freedom from restrain Prevention of chip and dirt accumulation Effective lubrication
More informationNotes for Making Wood Rings With Stainless Steel Insert Centers
Notes for Making Wood Rings With Stainless Steel Insert Centers Background These notes describe how to make a ring with a stainless steel (SS) insert and a wood exterior band. They also include information
More informationAn Adjustable Threading Feed Attachment for a Lathe Without Metric Threading Capability, by Ted Clarke
An Adjustable Threading Feed Attachment for a Lathe Without Metric Threading Capability by Ted Clarke Metric pitch threads, with the exception of the Royal Microscopical Society (RMS) 36 threads per inch
More informationGouge Jig SVD-186 (SVD-186)
Gouge Jig SVD-186 (SVD-186) TURNING TOOLS Bowl gouges Spindle gouges Turning cutters CARVING TOOLS Curved gouges Spoon-shaped gouges Back bent gouges Down bent gouges Curved V-tools Max tool width 36 mm
More informationHow to Edge Joint Boards
How to Edge Joint Boards It s unusual to find solid boards much over 300mm wide, and anything over about 150mkm is likely to be unstable. So for wide solid pieces it is necessary to edge joint boards together
More informationENGINE REBUILDING MACHINES
ENGINE REBUILDING MACHINES Zylinderbohrwerke: Typ MA Typ SIRIO Typ SPES Typ ORION Typ OLYMPIA 19 MA OLIMPIA ORION SPES SIRIO 20 Automatic emergency stop system. Total shutdown in case of accidental impact
More informationw w w. h d o n l i n e s h o p. d e TIMKEN BEARING CONVERSION TOOL GENERAL INSTALLATION -J04672 REV Kit Number Models
-J067 REV. 008-07- GENERAL Kit Number 8-08 Models TIMKEN BEARING CONVERSION TOOL For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com
More informationASSIGNMENT 4. Textbook Assignment: The point, edge, face, heel, and tang are the five parts of which of the following tools?
ASSIGNMENT 4 Textbook Assignment: "Files," "Grinders and Sharpening Stones," "Scrapers," "Awls," "Bolt and Cable Cutters," "Glass Cutters," "Knives,' 'Pipe Cutting and Threading Tools," "Tube Cutting and
More informationHornsby Woodworking Men s Shed. Guide to the Shed s Woodworking Machines
Guide to the Shed s Woodworking Machines SP00 Purpose The primary purpose of this document is to assist the induction of new members of the Hornsby Woodworking Men s Shed in the identification and understanding
More informationSaw, Files, Grinders and Brushes
ß 7005-7008 0 Overall length approx. 295, working length approx. 15, trim height approx. 25. 7005 Smooth, hardened cast steel wire, 0,35 Ø. Wire scratch brushes 7007 Brass wire, fine, 0,15 Ø, crimped.
More informationInventory (Figure 2) Copyright November, 2007 By Grizzly Industrial, Inc. Revised MAY, 2011 (JB)
MODEL T10024 ACCESSORY KIT #2 FOR T10010/T10097 WET GRINDER INSTRUCTION SHEET Introduction The Model T10024 Accessory Kit #2 for the Model T10010/T10097 Wet Grinder helps sharpen chisels and dress grinding
More informationMANUFACTURING TECHNOLOGY
MANUFACTURING TECHNOLOGY UNIT V Machine Tools Milling cutters Classification of milling cutters according to their design HSS cutters: Many cutters like end mills, slitting cutters, slab cutters, angular
More informationGolf Trolley Workshop (Devon)
Golf Trolley Workshop (Devon) Powerpole General Assembly Instructions Assemble the red and black plastic housings together correctly on the first try, they fit snugly and can be difficult to get apart.
More informationRockin' the Rockers. Ed Hollingsworth
Rockin' the Rockers Ed Hollingsworth I'm spending my spare time these days rebuilding a 1974 Triumph TR6. I had the well-worn 2.5 liter straight six engine all apart, and was assessing the toll that 40
More informationANDERSON POWERPOLE CONNECTORS FOR HAM OPERATORS
ANDERSON POWERPOLE CONNECTORS FOR HAM OPERATORS The Anderson Powerpole connector is a very good connector to sharing connections between users for such things as batteries, radios, chargers and other DC
More informationGeneral Machine Instructions
General Machine Instructions Cyclone Cyclone Plus Storm Storm Plus Note these instructions are based on the Cyclone machines, But the Cylinder Section is the same on the Storm Machines Tempest Tempest
More informationToolpost for HBM 290 lathe
Toolpost for HBM 290 lathe When I bought a new lathe it came with just a square toolpost so I had to use shims to get the tool to correct height. I decided to make a simple toolpost with tool-holders with
More informationPAN AND BOX BRAKE INSTRUCTIONS. Item #20649
PAN AND BOX BRAKE INSTRUCTIONS Item #20649 The EASTWOOD 12 & 24 PAN AND BOX BRAKES are precision engineered metal working tools designed to produce accurate, variable length bends in angles up to 135 in
More informationLumber Smith. Assembly Manual. If you are having problems assembling the saw and need assistance, please contact us at:
Lumber Smith Assembly Manual If you are having problems assembling the saw and need assistance, please contact us at: 804-577-7398 info@lumbersmith.com 1 Step 1 Safety Carefully read the Owners Manual.
More informationModule 4 General Purpose Machine Tools. Version 2 ME, IIT Kharagpur
Module 4 General Purpose Machine Tools Lesson 22 Use of various Attachments in Machine Tools. Instructional objectives At the end of this lesson, the students will be able to; (i) Comprehend and state
More informationPEPPERMILL CONSTRUCTION
PEPPERMILL CONSTRUCTION I ve been asked a several times to put together a review of how I turn peppermills. They are a great project, perfect for gifts and a lot of fun to make. They don't require especially
More informationInlay String Thicknesser
Inlay String Thicknesser 05P32.10 The Veritas Inlay String Thicknesser is used to scrape veneer or inlay string to a desired thickness. Unlike a conventional scraper, the sole of this tool does not bear
More informationBuilding a vertical wobbler
Building a vertical wobbler I wanted to build a simple steam engine that would also run on compressed air. At Chris Heapy s website (http://easyweb.easynet.co.uk) I found drawings of a small double acting
More informationBuilding Bigger Things. Woodworking Tools and Machinery. Marking Gauge. Thumb Screw. Stop Screw. Shoe. Beam. Pin. Head. Face Plate
Woodworking Tools and Machinery Pin Shoe Face Plate Thumb Screw Head Stop Screw Beam Marking Gauge A marking gauge is used to mark a uniform width on a board. The steel combination square discussed in
More informationROOP LAL Unit-6 Lathe (Turning) Mechanical Engineering Department
Notes: Lathe (Turning) Basic Mechanical Engineering (Part B) 1 Introduction: In previous Lecture 2, we have seen that with the help of forging and casting processes, we can manufacture machine parts of
More informationSmall Scraping Plane 05P29.50
Small Scraping Plane 05P29.50 U.S. Des. Pat. D609,548 The Veritas Small Scraping Plane is used for the final smoothing of small, flat surfaces, even if they are highly figured, or small areas of difficult
More informationOdd Wobbler Instructions By: Don Geiger
Odd Wobbler Instructions By: Don Geiger Stock Size Calculations and Reference Table When preparing stock material for turning an Odd Wobbler, you will need two pieces of dry wood that is about one inch
More information1. Actuate the upper die release button located in the C head or closed head. 2. Slide the nest into place in C head or closed head. See Figure 2.
The die assemblies consist of stationary dies (nests) and moving dies (anvils). The dies are retained in the crimp tool by retainer pins. Refer to the table in Figure 3 to ensure the compatibility of die
More informationTURNING TOOLS CARVING TOOLS
Multi Jig SVS-50 (37592) TURNING TOOLS Square and skew chisels with straight or curved edges. Max width 32 mm (1¼"). Parting tools Beading tools Roughing gouges Max width 50 mm (2"). CARVING TOOLS Gouges,
More informationLocoGear. Technical Bulletin - 14 November 28, 2003 Copyright 2003 by LocoGear LIVE STEAM CASTINGS. Tech Bulletin - 14
LIVE STEAM CASTINGS LocoGear Tech Bulletin - 14 John D.L. Johnson 3879 Woods Walk Blvd Lake Worth, FL 33467-2359 jjohnson@locogear.com www.locogear.com Technical Bulletin - 14 November 28, 2003 Copyright
More informationHand-Scraping Hardwood Floors in Residential Homes:
Hand-Scraping Hardwood Floors in Residential Homes: A manual for the hand-scraping process Marshall McKee Table of Contents Table of Contents Table of Contents... iii Table of Figures... iii Hand-scraped
More informationChisels. A set of Dovetail Paring chisels from Blue Spruce Toolworks (www.bluesprucetoolworks.com).
7 Chisels CHISELS MAKE UP A LARGE AND IMPORTANT part of the woodworker s tool kit. The apparent simplicity of a chisel a blade on a stick belies the numerous variations on that theme. At the very least,
More informationScrews. Introduction. 1. Nuts, bolts and screws used to clamp things together. Screws are used for two purposes:
Screws Introduction Screws are used for two purposes: 1. To clamp things together. 2. To control motion. 1. Nuts, bolts and screws used to clamp things together. Nuts, bolts and screws that are used for
More informationCrestline Dampening System. Installation Instructions. Ryobi 2700, 2800, 3200, 3200E Itek 950, 960, 975 Parent. X /98 Rev-A
Crestline Dampening System Installation Instructions Ryobi 2700, 2800, 3200, 3200E Itek 950, 960, 975 Parent X88-30 3/98 Rev-A GENERAL INFORMATION ATTENTION CRESTLINE DAMPENER OWNER! Accel Graphic Systems
More informationMINI-LATHE QUICK CHANGE TOOL POST
MINI-LATHE QUICK CHANGE TOOL POST Cutting and assembly details Machinists should familiarize themselves with the contents of this section before jumping in to the drawings. Many details are described here
More informationJUMBO STENCIL CUTTING MACHINE PARTS LIST AND OPERATING MANUAL
JUMBO STENCIL CUTTING MACHINE PARTS LIST AND OPERATING MANUAL Marion, IL USA STK. NO. 5800-152, REV A Warning: This machine contains pinch points which can injure personnel when not used properly. This
More informationBid Item # Item Bid Amount High Bid By 1 Smoke Eater $ Jerry Heinen 2 Welding Station $ HCO - Doug Wildeman 3 Game Bike $ -
Bid Item # Item Bid Amount High Bid By 1 Smoke Eater $ 51.00 Jerry Heinen 2 Welding Station $ 22.00 HCO - Doug Wildeman 3 Game Bike $ - 4 Air Compressor $ 150.00 Andrew Turner 5 Black File Cabinet $ 5.00
More informationPRO System with Dedicated Automatic Kerf Keeper Installation Manual - SP-2 (V1.0) 0706
SP2 Micro Jig, Inc. PO Box 195607 Winter Springs, FL 32719, USA. Tel: 1-407-696-6695 Web site: www.microjig.com Email: sales@microjig.com Copyright 2006 Micro Jig, Inc. MJ Splitter PRO System with Dedicated
More informationHinge-Boring Jig 05J07.01
Hinge-Boring Jig 05J07.01 This versatile jig contains a built-in carbide cutter and is designed to be powered by your own electric drill. It will locate cup and screw holes for 35mm cup hinges. With this
More informationCommercial Products Fundamentals of Reel Mowers
Commercial Products Fundamentals of Reel Mowers PART NO. 98008SL, Rev. B This page is intentionally blank. Fundamentals of Reel Mowers 1 Table of Contents Historical Background... 2 Theory of Operation...
More informationTHE BLADESHARPENER OWNERS MANUAL
THE BLADESHARPENER OWNERS MANUAL Photo shows knife in 100mm flip over. All parts will interchange. Note: Wedge attachment left of photo and sharpening stones are not included. 1 BLADESHARPENER WITH FLIPOVER
More informationReasons to Own a Shoulder Plane
9 Reasons to Own a Shoulder Plane Fine-tune your joinery with these tips and techniques B y C h r i s G o c h n o u r It s easy to dismiss the shoulder plane as a specialty plane, another way of saying
More informationRebuilding the Ram Ways on my Gingery Shaper, version 1.1
Rebuilding the Ram Ways on my Gingery Shaper, version 1.1 By R. G. Sparber Copyleft protects this document. 1 The original Gingery Shaper was designed more than 20 years ago. Many people have built them
More informationLapping Plate 05M20.20
Lapping Plate 05M20.20 U.S. Des. Pat. D593,140 Lapping is the process of rubbing two surfaces together with an abrasive and a lubricant to improve the quality of at least one of the surfaces. Although
More informationThe Canadian Tire Paint Roller A Technical Description
A Technical Description Eric Morlang Table of Contents 1. General Description of the Paint Roller... 3 2. Part-By-Part Description of the Paint Roller... 4 2.1 Body... 4 2.1.1 Handle... 4 2.1.2 Wire...
More informationScraping Plane 05P29.01
Scraping Plane 05P29.01 U.S. Pat. No. 7,444,750 The Veritas Scraping Plane is used for the final levelling and smoothing of large, flat surfaces, even if they are highly figured, prior to applying a finish.
More informationPRODUCT SERVICE MANUAL FOR CIG Mechanical Seal Triple Pumps
PRODUCT SERVICE MANUAL FOR CIG Mechanical Seal Triple Pumps WARNING The Imo General Installation Operation, Maintenance, and Troubleshooting Manual, (No. SRM00046), as well as all other component manuals
More informationIntroduction: The T30069 Center Punch Tool installs BAND-IT 3/8" and 5/8", 201 Stainless Steel and Galvanized Carbon Steel clamps.
Instruction Manual Introduction: The Center Punch Tool installs BAND-IT 3/8" and 5/8", 201 Stainless Steel and Galvanized Carbon Steel clamps. Table of Contents: 1. Introduction & Safety Practices 2. Operating
More informationS A F T E Y W A R N I N G
BINDING CUTTING BASE This tool is designed to fit on a Porter Cable Model 310 and 3701 trim router, this combination will provide you with an easy way to accurately cut a binding rabbet on you instrument.
More informationTech Tip 8 Controlling Photopolymer Plate Gauge
Tech Tip 8 Controlling Photopolymer Plate Gauge MacDermid photopolymer plates are manufactured to the highest quality standards to assure the best image reproduction and the longest press life. One important
More informationMetals can be bought from suppliers in standardized forms and sizes, such as round,
1.4 METAL CUTTING BAND SAWS: Metals can be bought from suppliers in standardized forms and sizes, such as round, rectangular or square bar stock or in the form of large sheets (plates). Bar stock normally
More informationINSTRUCTION MANUAL SM-330/ 430/ 936/ (Semi-Automatic Divider Rounder)
INSTRUCTION MANUAL SM-330/ 430/ 936/ 1136 (Semi-Automatic Divider Rounder) INSTRUCTION IMPORTANT INSTRUCTION THE INFORMATION IN THIS MANUAL IS CRUCIAL, MAKE SURE THAT THIS MANUAL HAS BEEN MADE AVAILABLE
More informationAhsanullah University of Science and Technology (AUST) Department of Mechanical and Production Engineering
Ahsanullah University of Science and Technology (AUST) Department of Mechanical and Production Engineering LABORATORY MANUAL For the students of Department of Mechanical and Production Engineering 1 st
More informationIntroduction: The T30069 Center Punch Tool installs BAND-IT 3/8" and 5/8", 201 Stainless Steel and Galvanized Carbon Steel clamps.
Instruction Manual Introduction: The Center Punch Tool installs BAND-IT 3/8" and 5/8", 201 Stainless Steel and Galvanized Carbon Steel clamps. Table of Contents: 1. Introduction & Safety Practices 2. Operating
More informationHow to Change the Flint and Wick in a Scripto Vu-Lighter 2011 by Andrew G. Rowe Version 1.01 Table of Contents
How to Change the Flint and Wick in a Scripto Vu-Lighter 2011 by Andrew G. Rowe Version 1.01 Table of Contents Foreword Chapter 1: Page 2 - Flint Replacement Chapter 2: Page 4 Wick Replacement Foreword
More informationAssembly & Construction Procedures
Assembly & Construction Procedures Foreword: This device was designed as an open source open architecture technology. With that in mind the construction of this device was made to be extremely flexible.
More informationMATERIALS & TOOLS REQUIRED INTRODUCTION. Before you start turning, read and understand this entire procedure.
INTRODUCTION This set of instructions shows one method to turn mills.there are many other possible variations and techniques. NOTE: These instructions are specific to 'Chef Specialties' mechanism. For
More informationBefore each patient, and at the first sign of dullness. When To Sharpen
3 4 Why Are We Here? Identify & preserve inst shape, sharpness, strength Understand inst landmarks & how to use them Evaluate, try, compare diff methods & technology?????????????? A Dull Story New (big
More informationCarBee-Sharp. Construction
CarBee-Sharp Congratulations on your purchase of the new CarBee-Sharp multi-head pocket carbide sharpener. CarBee-Sharp is the most convenient sharpener you will ever own. CarBee-Sharp is so small and
More informationJD-12. Instruction & Parts Manual
JD-12 Instruction & Parts Manual Framon Manufacturing Company, Inc. 909 W Washington Avenue Alpena, MI 49707 Phone: 989-354-5623 Fax: 989-354-4238 E-mail: support@framon.com Website: www.framon.com The
More informationHow to Sharpen a Knife
How to Sharpen a Knife Even a good knife will lose some of its sharpness with time. However, sharpening a knife is easy if you have the right tool and know how to use it. Generally three different materials
More informationDon t lap just yet. Red Wing
Don t lap just yet Red Wing 2 Guide The perfect valve/casing repair ensures The valves go up and down smoothly and lightly No matter how off-centered it is pushed down Tolerances are maintained Bearing
More information7x --Tailstock Cam Lock
7x --Tailstock Cam Lock By Magic Brian magicbrian40@yahoo.com Probably the most pleasing mod to have, but often not done through lack of milling facility s This version does NOT require a mill. MATERIALS
More informationGeorge Hatfield Demonstrates for CMW April 10, 2010 By Bob Gunther Photographs by Tina Collison
George Hatfield Demonstrates for CMW April 10, 2010 By Bob Gunther Photographs by Tina Collison Overview: George Hatfield is from Sidney, Australia. He entered the woodturning field as an apprentice and
More informationCollege of Forestry 610: Power Tools
College of Forestry 610: Power Tools Safety Policy & Procedure Manual Section 600: Workshops and Shop Tools Effective: 01 January 2007 Revised: August 2014 PURPOSE The purpose of this section is to provide
More informationSharpening Hand Tools
Sharpening Hand Tools FYI- don t buy this flattening stone Aaron Moore 2013 When It Comes to Sharpening All hand tools need to be sharpened regularly for good performance. It cannot be avoided and you
More informationSURFACE FINISH MAINTENANCE
SURFACE FINISH MAINTENANCE SURFACE FINISH MAINTENANCE Lumec strongly recommends that you maintain your luminaires twice a year in order to prolong the appearance of the finished surface. By following this
More informationVARIABLE SPEED WOOD LATHE
MODEL MC1100B VARIABLE SPEED WOOD LATHE INSTRUCTION MANUAL Please read and fully understand the instructions in this manual before operation. Keep this manual safe for future reference. Version: 2015.02.02
More informationAll American Mower Blade Sharpener Mulching Blade Model Patent Pending
All American Mower Blade Sharpener Mulching Blade Model 5000 Patent Pending Revised May 3, 2017 Attaching the guide pin to your grinder: Assembly and Use Locate the guide pin (included with the sharpener)
More informationInstruction Sheet Model SB1296/SB1297 Magnetic Chuck
Instruction Sheet Model SB1296/SB1297 Magnetic Chuck Magnetic chucks are heavy! Get assistance if needed when installing or removing the magnetic chuck from the surface grinder. Wear heavy duty leather
More informationP225 STANDARD FEATURES OPTIONAL FEATURES
CIRCULAR COLD SAWS P225 Manually operated Robust sawing head miters 45 left Bench top model no base Single blade speed of 1 HP Manual vise Material work stop rod for multiple cuts of the same length Flood
More informationThorvie Instructions Always wear eye protection and do not wear loose clothing when operating machinery. FOR AV- 41 ICE AUGER MACHINE
FOR AV- 41 ICE AUGER MACHINE 1. Please study video and all instructions before proceeding to grind. For Mora, Jeffy and Eskimo blades use the 6 brown resin bond wheel. Mount with washer and left-hand nut
More informationDRILL GRINDING ATTACHMENT
DRILL GRINDING ATTACHMENT To suit TM6025Q TOOL AND CUTTER GRINDER OPERATION S MANUAL 1 0º 270º 90º 180º INTRODUCTION Before grinding any cutters, you must set up the attachment to suit the type of cutter
More informationUnion County Vocational - Technical Schools Scotch Plains, New Jersey
SECTION 099123 - INTERIOR PAINTING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationV twin cylinder steam engine
V twin cylinder steam engine I got inspired to make this V twin steam engine after reading R. Griffinn s build articles in ME 4396. It is based on Stuart s V-twin double-acting oscillator, but since I
More information400GTO Lubrication Guide
400GTO Lubrication Guide Lubrication Guidelines for the following equatorial mounting: 400GTO Servo with GTOCP2 or CP3 Controller For other 400 models please review other postings as they become available.
More informationMODEL G4017 G4020 ARBOR PRESS INSTRUCTIONS
MODEL G4017 G4020 ARBOR PRESS INSTRUCTIONS For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com Introduction This arbor press is designed to perform
More information