INSTRUCTION MANUAL SM-330/ 430/ 936/ (Semi-Automatic Divider Rounder)

Size: px

Start display at page:

Download "INSTRUCTION MANUAL SM-330/ 430/ 936/ (Semi-Automatic Divider Rounder)"

Theresa Page
5 years ago
Views:

1 INSTRUCTION MANUAL SM-330/ 430/ 936/ 1136 (Semi-Automatic Divider Rounder)

INSTRUCTION IMPORTANT INSTRUCTION THE INFORMATION IN THIS MANUAL IS CRUCIAL, MAKE SURE THAT THIS MANUAL HAS BEEN MADE AVAILABLE TO ALL PERSONNEL WHO MAY OPERATE

2 INSTRUCTION IMPORTANT INSTRUCTION THE INFORMATION IN THIS MANUAL IS CRUCIAL, MAKE SURE THAT THIS MANUAL HAS BEEN MADE AVAILABLE TO ALL PERSONNEL WHO MAY OPERATE THE MACHINE. READ, UNDERSTAND AND FOLLOW THE WARNNINGS AND INSTRUCTIONS CONTAINED IN THIS MANUAL. Model: Serial Number: Manufacture Date: Installation Date: - 1 -

3 WORKING SAFETY Working Safety The machine must be used only by personnel suitably trained for the purpose and who has been trained in the contents of this publication. To ensure safe work, comply with the following instructions: 1. Install the machine in compliance with workplace safe requirement. 2. Use the machine with great care and never be distracted. 3. Do not wear loose fitting clothing or clothing with wide or open sleeves. 4. Do not remove, cover or modify the identification plates placed on the machine body. 5. Do not bypass the mechanical and electrical protection device. 6. Work on the products permitted and not on other types. 7. Do not use the machine as a working top and do not place any objects on it that are not required for normal working operations. 8. Do not use the machine with temporary electric connections or non-insulated cables. 9. Periodically check the state of the power cable and cable clamp on the machine body, replace it as soon as is necessary by qualified personnel. 10. Stop the machine immediately as soon as there is defective or abnormal operation, a breakage, incorrect movements, or unusual noise. 11. Before cleaning or carrying out maintenance, disconnect the machine from the power supply. 12. Use protective working gloves for cleaning and maintenance

4 CONTENT Introduction (4) Installation & Commissioning (5) Set-up & Operation (7) Cleaning & Maintenance (10) Parts List (12) Wiring Diagram (19) - 3 -

5 INTRODUCTION Brief Introduction These machines are specially used for dough dividing and rounding, they can divide and round the dough for Bun evenly with very little difference in weight and structure. And with the semi-automatic system, it can save large labor working that only two persons are needed. The machine has proved to gently handle a wide variety of dough and produce a high quality product. All of the information, illustration and specification contained in this manual are based on the latest product information available at the time of printing. SINMAG reserves the right to make changes at any time without notice. If questions arise during the operation or servicing, please contact us before proceeding. Features 1). Can divide the dough evenly. 2). Can round the dough greatly. 3). The machines can keep in a good status with lubricating oil. 4). Can turn over the machine head and easy to clean the knives with loosen one side pin of the machine head. 5). Can save large working time and finish rounding just in 8 seconds. Specification - 4 -

6 INSTALLATION AND COMMISSIONING Installation The machine is supplied factory lubricated and ready to run. After uncrating the machine, inspect it carefully to see whether there is any damage that might have occurred during shipment. Report any damage to us before proceeding. Never attempt to operate this machine with damaged or inoperable parts. Check for the following in the package: three moulding plates, one pressing lever, one plastic bottle of transmission oil (check inside the base). The divider rounder should be positioned on a lever floor of appropriate strength and stability, also with a convenient location that allows for easy access to the units controls and working areas, as well as to the top, front and sides for maintenance. Electric Connection Before making any electric connection, read the specifications on the nameplate to ensure that they agree with your power supply. Electric connection should be made by a qualified service technician who will observe all applicable safety codes and the national electrical codes. Appropriate electrical service should be available within the reach of the included electrical wires. Do not use any extensions to connect the machine electrical wires to the electrical outlet. An air circuit breaker should be added to the main switch near the machine, and 1.5m high above the ground for the electric supply. The machine must be in ground protection

7 INSTALLATION AND COMMISSIONING Commissioning After the machine is connected with the right power supply, use the rounding handle to see if the rounding plate is running in the direction of the arrow as indicated on the front side of the machine. If not, swap any two of the three phases, and restart the machine again until the plate runs in the right direction

8 SET-UP AND OPERATION Set-up Machine Check Out Without dough, insert and lock one rounding plate on the Index Pin. Be certain the rounding table and rounding plate are clean with no foreign trapped between them, and the rounding plate is completely flat on the rounding table. Lower the dividing head by pulling down the pressing lever until it stops in the down position. This is the pressing operation, which evenly distributes the dough in the dividing head to assure uniform weight for each division. While holding the pressing lever down, slowly push the rounding lever downward to actuate the rounding cycle (see figure 2). The moulding table and the moulding plate will shift sideways, and it will cause the moulding plate to move in a circular motion if the motor is turned on. After several - 7 -

9 SET-UP AND OPERATION seconds, slowly return the rounding lever to the fully raised rest position. This is the rounding cycle, which rounds the dough pieces into dough balls. Slowly return the pressing lever to the fully raised rest position. Remove the moulding plate by first pulling it up off the the locking pin and then straight out from the front of your Bun Divider Rounder. Note: Check dividing plate for any unusual marks or scratches caused by the knives coming into contact with the dividing plate. If marks or scratches are detected, call your dealer for service advice. Operation Steps 1). The dough is placed into a Moulding Plate within the marked circle. Flatten dough a little. 2). Place Moulding Plate with dough onto the Rounding Table of the machine. Do not flour the Moulding Plate. 3). Press dough by pulling down Pressing Lever. 4). Operate Cutting Lever (top part ball handle) and cut by pulling down Pressing Lever further. When operating the Cutting Lever, do not release Pressing Lever, press through immediately. 5). Keep Pressing Lever in bottom position and press Roulding Lever evenly sideways. Let Rounding table rotate for 3-5 seconds and return to zero position. 6). Lift Pressing Lever to stop position and remove Moulding Plate with the divided and rounded dough pieces

10 SET-UP AND OPERATION Weight Adjustment For the best rounding result, the rounding space must be adjusted according to the weight of the dough piece. This can be done by altering the position of the Volume Bar. Loosen the locking sleeve, set the Volume Bar and tighten the locking sleeve again. The scale on the Volume Bar is for reference only. The position of the volume bar must be changed to suit the dough. If the Bar is setted too small, it may damage the surface of the dough. Also if the Bar is setted too high, it may result in the dough not rounding properly. Before the dough is put into the machine, please ensure that it has had an adequate rest time

Remove the pull pin from the end of Locking Pin on one side only. 5).

11 CLEANING AND MAINTENANCE Daily Cleaning Procedure 1). Brush off all external surfaces using a banister brush and work from top to bottom. 2). Wipe all surfaces with a damp cloth. Dry all external surfaces. 3). Remove the two Hoods. 4). Remove the pull pin from the end of Locking Pin on one side only. 5). Twist Dough Retaining Ring in an clockwise direction, low onto rounding Table and remove from the machine. Scrape Dough Retaining Ring only with a plastic scraper. 6). Using the Pressing Lever rotate the Pressing head assembly to allow the blades to be exposed

12 CLEANING AND MAINTENANCE 7). Using a plastic scraper scrape and sweep old dough and build up deposits from the divider head and Rounding Table. Lightly oil divider head(use food grade oil only). 8). Engage dividing lever and pull on Pressing Lever to expose the dividing knife surfaces. 9). Scrape all the divider sufaces using a plastic scraper, then lightly oil (use food grade oil only). 10). Use two people to reposition the Pressing Head back to its upright working position. 11). Locate and put back the Locking Pin. Note: Do not hit into position with a hammer or metal object. 12). Put back the Pressing Ring and Hoods. Maintenance It is recommended that this machine should be lubricated and serviced by an authorised service person every three months

13 PARTS LIST

14 PARTS LIST

15 PARTS LIST

16 PARTS LIST

17 PARTS LIST Parts Number Machine Model Parts Code Parts Name Specification 001 SM330/430/ D SM936 14D Fixed Mandrel 2PCS SM330/430 14D SM936 14D Main Shaft SM D SM330/430 13D Cover Board Of Knife SM936 13D Seat SM D Z1 004 SM330/430/936/ D Handle 005 SM330/430/936/ D136-01A Pin of Handle SM330 13D SM530 13D SM936 13D Knife Seat SM D Z1 SM330/430 14D SM936 14D Cross Frame SM D SM330/ D SM430/936 14D Tension Spring 1PCS 009 SM330/430/936/ D Tension Spring 4PCS 010 SM330/430/ D SM936 14D Screw With Scale 011 SM330/430/936/ D Plastic Orb 012 SM330/430/ D SM936 14D Adjusting Screw 013 SM330/430/936/ D Press-holder 014 SM330/430/936/ D Segment Gear SM330 14D SM430 14D Dough Frame SM936/ D SM330/430/936/ D136-01B Handle Of Holder SM330 14D166-01R 017 SM430 14D166-05R SM936 14D166-02R Red Plastic Plate RED (ABS) Sm D166-03W-Z1 018 SM330/430/936/ HQL38*1/2*12 Black Plastic Ball φ38*1/2* SM330/430/936/ D Control Staff 020 SM330/430/936/ D Mandrel Of Control Staff 021 SM330/430/936/ D Fixed Bolt 022 SM330/430/936/ DPL330 Lamp 023 SM330/430/936/ KGLHE-PKZO-G Switch Box 024 SM330/430/936/ D Pisciform Block

18 PARTS LIST 025 SM330/430/936/ D Screw for Spring 5PCS 026 SM330/430/ D SM936 13D Bridge Fixed Seat 027 SM330/430/936/ D Rotary Seat 028 SM330/430/936/ D Sliding Shaft Seat 029 SM330/430/936/ D Mandrel Of Sliding Piece 030 SM330/430/936/ D Sliding Piece 031 SM330//936 14D SM430/ D Motor Pulley FOR 50HZ 032 SM330/430/936/ PDL3V-375 Belt 3PCS 033 SM330/430/936/ D Pulley 034 SM330/430/936/ MDL330-3PH-KDY Motor 230/400V-50/6 0HZ-3PH 035 SM330/430/936/ D155-02A Pendulum Frame 036 SM330/936/ D SM430 14D Tension Spring 037 SM330/430/936/ D Shaft 038 SM330/430/936/ D Lever Seat 039 SM330/430/936/ D Seat 040 SM330/430/936/ D Guide Mandrel 041 SM330/430/936/ D Double Active Seat For Lever 2PCS 042 SM330/430/936/ D Sleeve 043 SM330/430/936/ KGLPKZM0-4 Switch 3PH 044 SM330/430/936/ ZCLNU206 Bearing 045 SM330/430/936/ DZL330 Lamp Seat 046 SM330/430/936/ D Counterweight 047 SM330/430/936/ D Screw Rod 048 SM330/430/936/ D Holder 049 SM330/430/936/ D Bearing Cover 050 SM330/430/936/ DZL01 Lamp Cover 051 SM330/430 14D186-01H SM936/ D186-01J Plastic Pad SM330 14D SM430 14D SM936 14D Knives SM D SM330/430/ D142-01A SM936 13D142-02A Rounding Plate 054 SM330/430/936/ D Moulding Plate Index Pin 055 SM330/430 13D SM/936/ D Arch Seat 056 SM330/936/ D SM430 14D Scale Screw Plate

19 PARTS LIST 057 SM330/430 13D SM936/ D Fixed Hanger 058 SM330/430/936/ D Baffle Fixed Screw 059 SM330/430/936/ D Rolling Mandrel 060 SM330/430/936/ D Bush Thick 061 SM330/430/936/ D Bush Small 062 SM330/430/936/ D Sliding Axle Housing 063 SM330/430/936/ D Bearing Housing Sleeve SM330/430 11SM SM936 11SM Machine Body SM SM SM330/430/936/ D Mandrel 066 SM330/430/936/ D Hanger Seat 067 SM330/430/ D SM936 14D Linker SS41 8t*25* SM330/430/936/ D Adjusting Screw 069 SM330/430/936/ D Tension Spring 1PCS 070 SM330/430/ D SM936 14D Shaft 071 SM330/430/936/ D Link Stick 072 SM330/430/936/ D Support Seat 073 SM330/430/936/ D Screw Buckle 074 SM330/430/936/ D Spring Block 075 SM330/430/936/ D Screw 076 SM330/430/936/ D Adjusting Screw Rod 077 SM330/430/936/ D Motor Limited Board 078 SM330/430/936/ D Lever Mandrel 079 SM330/430/936/ ZCL6210VV Bearing 2PCS 080 SM330/430/936/ D Plate 081 SM330/430/936/ D Pin 082 SM330/430/936/ D Bolt For Tension Spring 083 SM330/430/936/ D Support Board 084 SM330/430/936/ D Protect Cover 085 SM330/430/936/ D Protect Cover 086 SM330/430/936/ D Machine Side Cover SPCC 2.0T*290* SM330/430/936/ D Side Cover Board SPCC 2*290* SM330/430/936/ D Frame Sheath 089 SM330/430/ D142-01B SM936 14D142-02B Adjusting Block 090 SM330/430/936/ D Screw 091 SM330/430/936/ D U-form Block 092 SM330/430/936/ ZCL5205VV Bearing 1PCS

20 WIRING DIAGRAM

VARIABLE SPEED WOOD LATHE

MODEL MC1100B VARIABLE SPEED WOOD LATHE INSTRUCTION MANUAL Please read and fully understand the instructions in this manual before operation. Keep this manual safe for future reference. Version: 2015.02.02