Wood Christmas Tree Base [1]

Transcription

1 [1] Submitted by Ana White [2] on Mon, :34 [1] Well, here we are, well into December, well past Thanksgiving... and no tree up yet. I've been dreading putting a tree up. Page 1 of 31

2 And here's the reason: The one in the little HAPPY suit. His arms are much longer than they look. So what to do? The only thing I could think of short of building a gate around the tree was to elevate the tree with some sort of wood base crate thingy. Page 2 of 31

3 I love this one from That's My Letter (full tutorial here) [3] Page 3 of 31

4 And this one from The Turquoise Home (nice tutorial here) [4] But I needed something a little taller, a little more enclosed... and it's Sunday (which means all the stores are closed within 100 miles of me, so I gotta use scraps and work with what I have on hand). Page 4 of 31

5 So I came up with this! Not bad for a couple hours work and TWELVE BUCKS in lumber. Yes, that's right. I love cedar fence pickets. And 1x3 furring strips. So here's how I made it After cutting all my boards (I used a compound miter saw), I applied glue to the 1x3s, Page 5 of 31

6 I loaded up my Ryobi Airstrike stapler with 1" staples (if you don't have Page 6 of 31

7 one of these bad boys, seriously, beg Santa for one) Then attached the two outer boards to the 1x3 from the back. Page 7 of 31

8 Being square is always a good thing. NOTE: If you measure diagonally from outside corner to outside corner, the two diagonals should match. If they don't you are out of square and need to adjust by pushing the longer diagonal end points together. Do this before you put tons of staples in or let the glue dry. Page 8 of 31

9 Then I just centered the last remaining board in the middle and nailed it down. This is the smaller side panel complete. To build the two larger panels that need to cover the corners of the smaller panels, I took a quick measurement of the 1x3 plus the paneling, and cut my next 1x3 sets that much longer (times two for each end). Page 9 of 31

10 Then I marked this distance in on the 1x3s - for those of you with eagle eyes, I did not have enough cedar fence pickets so I made my own out Page 10 of 31

11 of 1/4" thick plywood ripped down in size for this project, but this plan calls for the fence pickets because they have more character and are easier to work with because you don't have to rip them to size. Then I just stapled the remaining two end panels together, leaving the 1x3 to overhang the ends as measured. Page 11 of 31

12 I then predrilled two holes on each end of the 1x3s where they overhang, Page 12 of 31

13 And used 2" wood screws to attach together the four panels at the Page 13 of 31

14 corners through the predrilled holes. I opted not to use glue here so I can take the stand appart after the holidays are over. To cover the top, I just added a few 1x3 cleats inside, and rested more panels on top. That way I can get in there and water the tree easily Page 14 of 31

15 (and it will also remove and store flat with the rest of the tree cover stand) For the tree trunk hole, I drilled holes in the two remaining panel pieces with a hole saw bit, Page 15 of 31

16 And then just used my compound miter saw to cut the hole out to the side. Page 16 of 31

17 With the two pieces cut like this, Page 17 of 31

18 The tree trunk just sits in the middle, Page 18 of 31

19 And the two pieces just slide together to cover the opening. Page 19 of 31

20 For added detail, I stapled rope around in an X shape. Page 20 of 31

21 All done and ready for a tree!!! The plans follow, if you build, please share! I'd love to see your Christmas tree stand cover too! XO Ana + Family Summary: DIY wood Christmas tree base cover from Ana-White.com CategoriesProject Type: Outdoor [5] Page 21 of 31

22 Other Projects [6] Room: living room [7] Skill Level: Beginner [8] Dimensions: Dimensions shown above Page 22 of 31

23 4-5-1/2" x 72" cedar fence pickets 8 feet long Common Materials: 2 inch screws Elmer's Wood Glue [9] Tools: Page 23 of 31

24 [10] [11] [12] Page 24 of 31

25 [13] Cut List: 12 - cedar fence 17" long 17" long approx 19-1/2" long CUT TO FIT!!! 4 - cedar fence 16" long General Instructions: Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck! Page 25 of 31

26 [14] Build the two smaller panels. Page 26 of 31

27 [15] Build the two larger panels, with 1x3 ends overhanging enough to cover the ends of the panels built in step 1. Page 27 of 31

28 [16] Add a cleat inside the larger panels for the top to sit on. Page 28 of 31

29 [17] Attach the panels together at corners with 2" screws predrilled at corners. Page 29 of 31

30 [18] Place top panels on cleats. Finishing InstructionsPreparation Instructions: Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth. It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed. Source URL: Page 30 of 31

31 ristmas-tree-base Links [1] -base [2] [3] le.html [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14] 0stand%20wood%20cover%20base%20crate%20step%201.jpg [15] 0stand%20wood%20cover%20base%20crate%20step%202_0.jpg [16] 0stand%20wood%20cover%20base%20crate%20step%203.jpg [17] 0stand%20wood%20cover%20base%20crate%20step%204.jpg [18] 0stand%20wood%20cover%20base%20crate%20step%205.jpg Page 31 of 31