Groupwork Tables. Table of Contents. Page Topic. Page 1 of Rev G
|
|
- Elijah Hudson
- 5 years ago
- Views:
Transcription
1 Table of Contents Page Topic 2-13 T-Legs & s Installation 14 Typical Table Configurations 15 Wire Manager Installation Groupwork Tables To ensure stability and prevent possible injury, standing height and standard height post legs with casters are not permitted on any 18" deep tables and half-round tables smaller than 30 x 60. Standing height post legs with casters are not permitted on 24 x 42 kidney shape top and 24 x 48 trapezoid shape tops. NOTES: T-Legs and s provide a nominal table height of 28-1/2". Glides and casters are interchangeable, while keeping the same table height. The height range is 25-1/2" to 31-1/2" for adjustable T-Legs and adjustable s. The height range is 28-1/2" to 45" for standing height adjustable s. If you have a problem, question, or request, call your local dealer, or Steelcase Line 1 at 888.STEELCSE ( ) for immediate action by people who want to help you. (Outside the U.S.., Canada, Mexico, Puerto Rico, and the U.S. Virgin Islands, call: ) Or visit our website: Steelcase Inc. Grand Rapids, MI U.S.. Printed in U.S.. Page 1 of 15
2 ttaching Legs to Worksurfaces There is no difference in installation of fixed height and adjustable height legs. (Fixed Height and djustable Height) Standing Height (djustable Height Only) T-Leg (Fixed Height and djustable Height) CUTION: Post legs with casters are not to be used with 18" deep tables. See note on page 1 for details. Page 2 of 15
3 Rectangular Worksurfaces 18" and 24" Deep Pilot Hole Locations CUTION: Post legs with casters are not to be used with any 18" deep rectangular tops. See note on page 1 for details. 18"Deep 24"Deep 18" x 84" 24" x 84" ngled T-Leg 24" x 84" 24"Deep Keep screws in the first t-leg loose until the second t-leg, on the same end, is loosely attached to the table top. Tighten the screws starting from the middle of the table top and working towards the outside corner. 18" deep rectangular worksurfaces accommodate post legs only. Size (LPL or HPL) Post Leg race Size T-Leg race Size (inline) T-Leg race Size (angled) 18x60 39" Not needed Not needed 18x66 48" Not needed Not needed 18x72 48" Not needed Not needed 18x84 57" Not needed Not needed 24X60 57" Not needed 39" 24X66 57" Not needed 39" 24X72 57" Not needed 47" 24X84 72" Not needed 57" 30X60 57" 48" 57" 30X66 57" 57" 57" 30X72 57" 57" 57" Page 3 of 15
4 Rectangular Worksurfaces 30" Deep Pilot Hole Locations ngled T-Leg T-Leg Keep screws in the first t-leg loose until the second t-leg, on the same end, is loosely attached to the table top. Tighten the screws starting from the middle of the table top and working towards the outside corner. Page 4 of 15
5 Half Round Table without Cutout and (3) Legs CUTION: Post legs with casters are not to be used on any half round tops smaller than 30" x 60". See note on page 1 for details. T-leg 18" x 36" 24" x 48" 18" x 36" half round table w/o cutout accommodate post legs only. Page 5 of 15
6 Half Round Table without Cutout and (4) Legs ngled T-Leg and T-leg 30" x 60" 30" x 60" Page 6 of 15
7 Half Round Table with Cutout and (3) Legs CUTION: Post legs with casters are not to be used on any half round tops smaller than 30" x 60". See note on page 1 for details. T-leg 21" x 42" 27" x 54" 21" x 42" half round table w/ cutout accommodate post legs only. Page 7 of 15
8 Half Round Table with Cutout and (4) Legs ngled T-Leg and T-leg 30" x 60" 30" x 60" Page 8 of 15
9 Personal Tables 24" x 42" KIDNEY SHPED 18" x 36" personal table accommodate post legs only. 24" x 42" ngled T-leg Keep screws in the first t-leg loose until the second t-leg, on the same end, is loosely attached to the table top. Tighten the screws starting from the middle of the table top and working towards the outside corner. 24" x 42" KIDNEY SHPED 24" x 42" 18" x 36" CUTION: Standing height and standard height post legs with casters are not to be used on any of the above mentioned tops. See note on page 1 for details. Page 9 of 15
10 24" x 48" trapezoid tables accommodate post legs only. Trapezoid Tables 24" x 48" ngled T-Leg T-Leg 30" x 60" 30" x 60" 30" x 60" CUTION: Standing height post legs with casters are not to be used on 24" x 48" trapezoid tops. See note on page 1 for details. Standard height post legs with casters are allowed on 24" x 48" trapezoid tops. Keep screws in the first t-leg loose until the second t-leg, on the same end, is loosely attached to the table top. Tighten the screws starting from the middle of the table top and working towards the outside corner. Page 10 of 15
11 Triangle Tables Triangle tables accommodate post legs only. This product has been culled as of March CUTION: Post legs with casters are not to be used on these triangular tops. 24" Straight 30" Straight 36" Convex 42" Convex Page 11 of 15
12 Square Concave Tables ngled T-leg 42" 42" 36" 36" Page 12 of 15
13 Corner ubble Tables ngled T-leg This product has been culled as of March " 36" 30" 30" Page 13 of 15
14 Use style # TSTTIE when requiring (6) Tie Plates and (24) Screws. Use style # TSTPL14 when requiring a 14" Support Plate and (8) Screws. Use style # TSTPL20 when requiring a 20" Support Plate and (8) Screws. Typical Table Configurations Post legs and T-legs are interchangeable for all configurations. Post legs are shown. Triangle Table with Three Rectangular Tables Corner ubble Table with Two Rectangular Tables Two Half Round Tables with Two Rectangular Tables 24"/30" 14"D brackets for 24"D Tops 20"D brackets for 30"D Tops This product has been culled as of March " x 54" 24" 27" x 54" 30" 24"/30" 24"/30" 24" 30" 45º Corner Table with Two Rectangular Tables 90º Corner Table with Two Rectangular Tables 24" x 48" 18" 24" x 48" The 18", 24" & 30" product has been culled as of March " 18" 18" The 18" product has been culled as of March " 24" 21" x 42" 18" 21" x 42" 30" 30" 18" Page 14 of 15
15 Wire Manager Installation 1. Place wire manager underneath worksurface where desired. 2. ttach with three (3) screws. Wire manager can be mounted with the opening towards the user or away from the user. Modesty Panel Installation Prior to May Place modesty panel hole through bracket bolt. 2. Fasten with nut and washer. 3. Position modesty panel and bracket to underside of worksurface. lign modesty panel bracket with edge of table as shown (3a) and attach bracket to underside of worksurface using four (4) screws (3b) Flush Worksurface 2 3a Modesty Panel 3b Page 15 of 15
Opus Standard Corner Trim Unit
Opus Standard Corner Trim Unit If you have a problem, question, or request, call your local dealer, or Steelcase Line 1 at 888.STEELCASE (888.783.3522) for immediate action by people who want to help you.
More information488 Brody Disassembly Direction
488 Brody Disassembly Direction Lighting (see page 8) Screens (see page ) Backrest (see page 4) " and " BIT HOLDERS Side Surface (see page ) T0, T0, T40 TORX Personal worksurface (see page 6) Caddy (see
More informationTour Worksurfaces and Supports
R Tour Worksurfaces and Supports Table of Contents Topic Page COLUMN SUPPT SUPPT FRAME TIE BRACKET TO COUNTER Worksurface to Shelf Attachment 2 Worksurface to Counter Attachment Bracket 3 Worksurface Tied
More informationOpus Base Unit Assembly
Opus Base Unit Assembly 5/16" NOTE: All cam locks need to be rechecked to confirm they are tight before installation. Gaps could result if not completely tightened and effect assembly. 2 Foot Scrap Board
More information110 and 555 Markerboard, Chalkboard and Tackboard Mounting
0 and 555, Chalkboard and Tackboard Mounting 0 # BIT 0 Splined 0 and 555 Tackboard POWER GRIPS 555 If you have a problem, question, or request, call your local dealer, or Steelcase Line at 888.STEELCASE
More informationJenny Legs Assembly Instructions
Jenny Legs Assembly Instructions R EXTENDED PHILLIPS BIT MM ALLEN WRENCH 6MM HEX DRIVE /" 007 Steelcase Inc. Grand Rapids, MI 90 U.S.A. Printed in U.S.A. Page of 6 88000 Rev F Jenny Club Instructions:
More informationHeight Adjustable Benching End Panel and Utility Pole
Height Adjustable Benching End Panel and Utility Pole Tools required: END PANEL Jig Saw Power Drill END PANEL WITH UTILITY POLE Bit Holder Long #2 Square Drive Bit 5mm Hex Drive Bit UTILITY POLE Level
More information434 Cobi Chair - Seat Shell Replacement
434 Cobi Chair - Seat Shell Replacement PROFILE OF HARDWARE FOR CLARITY #8-18 x 1/2" Pan Head Tapping Screw Magnetic Bit Holder M6 x 45mm Wafer Head Screw T-30 Large flat-bladed screwdriver If you have
More informationSeries 9000 Panel Door; In-Line, Corner and Permanent Wall Application
Series 9000 Panel Door; In-Line, Corner and Permanent Wall Application 5/32" Drill Bit In-Line Corner Permanent Wall 3/16" Allen Wrench If you have a problem, question, or request, call your local dealer,
More informationSeries 7 AdjusTable Height Tables
Series 7 AdjusTable Height Tables Tools required: #2 Phillips Bit with Extension #2 Square Drive Bit 4mm Hex Drive Bit #3 Phillips Bit If you have a problem, question, or request, call your local dealer,
More informationPrivacy Wall & Glass Selections Pivot-Hinged Door (For products manufactured after September 14, 2009)
Privacy Wall & Glass Selections Pivot-Hinged Door (For products manufactured after September 14, 2009) 3/16" HEX BIT #2 ACR BIT 3/8" HEX SOCKET Full-Height (No Switch) Transom (No Switch) Full-Height (With
More informationPremium Whiteboard and Tackboard Mounting
Premium Whiteboard and Tackboard Mounting #2 BIT If you have a problem, question, or request, call your local dealer, or Steelcase Line 1 at 888.STEELCASE (888.783.3522) for immediate action by people
More informationSeries Adjustable Height Tables
Series 7.2 - Adjustable Height Tables Tools required: Power Drill #2 SQUARE DRIVE BIT If you have a problem, question, or request, call your local dealer, or Steelcase Line 1 at 888.STEELCASE (888.783.3522)
More informationc:scape Shared Tables - Freestanding and Tethered
c:scape Shared Tables - Freestanding and Tethered Furniture should be installed in sequence shown below. 1 2 3 4 5 6 BEAM MID STORAGE DESKING POWER LOW STORAGE PRIVACY THIS INSTALLATION SEQUENCE IS HERE.
More informationPrivacy Wall Glass Selections - Polished Edge Slider Door
Privacy Wall Glass Selections - Polished Edge Slider Door 3/6" HEX BIT PUTTY KNIFE #2 ACR BIT SUCTION CUP HOLDERS DOOR LEAF: Satin Tempered Clear Tempered LOCTITE 425 SIDE LIGHT ETCHED GLASS STYLES: Satin
More informationFlexFrame - Storage Components and Skins
FlexFrame - Storage Components and Skins 1/4 Square Drive Ball-Point Hex-Bit Socket 1/8 Short Hex, 1-1/2 Overall Length McMaster Part # 54075A44 Table of Contents Topic Page Storage Components 2 General
More informationUniversal Storage 1-Hi and 1.5-Hi Lateral File Counterweight Package
Universal Storage 1-Hi and 1.5-Hi Lateral File Counterweight Package 1-Hi 18" & 24 Deep Cabinets (pages 2-4) 1.5-Hi 18" & 24 Deep Cabinets Drawer/Drawer or Open/Drawer (pages 5-7) CAUTION Please refer
More information487 Cachet Swivel - Base Chair Replace Front Seat Support or Seat
487 Cachet Swivel - Base Chair Replace Front Seat Support or Seat SPECIAL ALLEN WRENCH PROVIDED If you have a problem, question, or request, call your local dealer, or Steelcase Line 1 at 888.STEELCASE
More informationModular & Hardwired Hub Assembly to "X" and "Y" Posts
Modular & Hardwired Hub Assembly to "X" and "Y" Posts Hardware Package T-Nut Data jack bracket #6 x 1/4" plastite trilobular screw 1/4-20 x 3/4" socket head cap screw #6-32 x 1/4" pan head screw #10-32
More informationAnswer Power Beam and Boundary Screen
Answer Power Beam and Boundary Screen 5/16 MAGNETIC 3/8 If you have a problem, question, or request, call your local dealer, or Steelcase Line 1 at 888.STEELCASE (888.783.3522) for immediate action by
More informationWorkbench Instructions for Assembly
Workbench Instructions for Assembly Technical Electronic Workstations and Industrial Workbenches Includes: Cabinets Privacy Panels Stringers Bottom Shelves Table of Contents Tools Required for Assembly...
More informationPathways Privacy Wall Glass Selections - Sliding Door
Pathways Privacy Wall Glass Selections - Sliding Door #2 ACR BIT 3/16" HEX BIT RAYBO ETCHED GLASS STYLES: Satin Mist PATTERN GLASS STYLES: Waterfall Bamboo Harp Mirage If you have a problem, question,
More informationSingle Sided Height Adjustable Benching
Single Sided Height Adjustable Benching Bit Holder Power Drill Long # Square Drive Bit 5mm Hex Drive Bit T-30 Torx Drive Bit Hex Key -.5mm (Provided) SERIES 5 Hex Key - 3mm Socket Adaptor (or) If you have
More informationLarge Case Storage - Counterweights
Large Case Storage - Counterweights Lateral File/Combo Cabinet CAUTION Please refer to the Steelcase Specification Guide for Storage for additional guidance on determining the correct counterweight package.
More informationTopo Freestanding Applications - Private Office
4 3 2 Topo Freestanding Applications - Private Office Combo Wrench If you have a problem, question, or request, call your local dealer, or Coalesse at 1.800.627.6770 Or visit our website: www.coalesse.com
More informationS48-L12-SC AND G48-L12-GC STEEL PORTA-DOCK S82 SC 6 X 12 PLATFORM AND G82 GC 6 X 12 PLATFORM
PAGE 1 OF 6 PORTA-DOCK, INC. S48-L12-SC AND G48-L12-GC STEEL PORTA-DOCK S82 SC 6 X 12 PLATFORM AND G82 GC 6 X 12 PLATFORM Thank you for purchasing our product! *Please read these instructions and follow
More informationPORTA-DOCK, INC. AP17 APD DS 4 X 16 T12 AW17 CPD DS 4 X 16 T12
Page 1 of 7 PORTA-DOCK, INC. AP17 APD DS 4 X 16 T12 AW17 CPD DS 4 X 16 T12 *For Beige Decking Add the Letter B to Model* Thank you for purchasing out product! *Please read these instructions and follow
More informationNote: This assembly instruction will cover all configurations of Alloy adjustable height double bases.
Note: This assembly instruction will cover all configurations of adjustable height double bases. 1 Screw in the provided adjustable glides into each leg as shown in Figure A. Two glides per leg. Figure
More informationWorkbench Instructions for Assembly
Workbench Instructions for Assembly FlexWorks is a trademark of Lista International Corporation. Making Workspace Work is a trademark of Lista International Corporation. Document Number: MD002A3 Print
More informationmedia:scape HDVC Wall Mount
Dual Shroud media:scape HDVC Wall Mount Single Shroud CAUTION Quad Shroud FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY. Triple Shroud Read the entire Assembly
More informationFitWork Walkstation Series 7 AdjusTables
FitWork Walkstation Tools Required: #2 Phillips Bit with Extension Page 1 of 20 A7TG660606H A7TR663232H FitWork Walkstation 4mm Hex Head Bit A7TG660632H A7TR383030H www.details-worktools.com A7TG663206H
More informationKai Installation Instructions
Kai Installation Instructions Before Beginning Installation Read through the entire instruction thoroughly A minimum of 2 people are required for this assembly These instructions reflect typical assemblies;
More informationModular Teacher s Desk Systems
Modular Teacher s Desk Systems ssembly Instructions 1 Modular Teacher s Desk Components Part Drawing Description Qty Part Drawing Description Qty 90390 djustable Leg-1S 90369 Modular Pedestal 90391 djustable
More informationinstallation guide ICON classic benching
installation guide ICON classic benching Index ICON Installation Guide Single Run Frame Assembly... Worksurfaces and Electrical... Attaching Worksurfaces to Frame...6 Installing optional accessories...7
More informationCNC Router Parts PRO Machine Kit Cable Track Installation Instructions
1 1 X CABLE TRACK TRAYS & BRACKETS The cable track on the side of the system is supported by a metal tray (or multiple trays for longer systems such as a PRO4896). These trays hang from brackets on the
More informationRange height adjustable assembly
Table of contents Digital handset operation 3 Height adjustable bench kit 4-5 Cable carrier 6 Ganging tray and ganging rail 7 Height adjustable return frame kit 8 Cable entry pole 9 24 and 30 d worksurfaces
More informationArlink 7000 Workstation
Arlink 7000 Workstation Instructions for Assembly Basic Bench Assembly Undersurface Accessories Above Surface Accessories Making Workspace Work is a trademark of Lista International Corporation. Creation
More informationNote: This assembly instruction will cover all configurations of Alloy adjustable height single bases.
Note: This assembly instruction will cover all configurations of adjustable height single bases. 1 With the leg upside down. Attach the freestanding foot to the bottom of the adjustable height leg using
More informationSeries 7 - Adjustable Height Tables
Page 1 of 22 Series 7 - Adjustable Height Tables Installation Instructions Tools required: #2 Phillips Bit with Extension #2 Square Drive Bit 4mm Hex Drive Bit Series 7 - Adjustable Height Tables Installation
More informationArlink 7000 Workstation
Arlink 7000 Workstation Instructions for Assembly Basic Bench Assembly Undersurface Accessories Above Surface Accessories VSI Mounting Instructions Making Workspace Work is a trademark of Lista International
More informationEquilibrium. Conference Table. Installation Instruction. Revision B 11/07/16
Equilibrium Conference Table Installation Instruction Revision B 11/07/16 Equilibrium End User Agreement Enwork Equilibrium table bases must be installed directly onto a four inch minimum thickness concrete
More informationRANGE DIGITAL HANDSET OPERATION. 1. Panel. 2. Initialization Procedure. 3. Move Up & Down. 4. Set Memory Positions. 5. Move to the Memorized Positions
INSTRUCTION SHEET #2577INS PART #1730534 DIGITAL HANDSET OPERATION OPERATION INSTRUCTIONS 1. Panel 1 Button: Preset 1 2 Button: Preset 2 3 Button: Preset 3 S Button: Select Display: Reads in 1 / 2 " Increments
More informationBF12-SERIES Flash Stands
BF12-SERIES Flash Stands Document # 16-462 Assembly and Operating Instructions Please review all these instructions prior to assembly. The BF12-SERIES stands come in two models, standard duty and heavy
More informationAssembly Instructions & General Overview
Assembly Instructions & General Overview 1. General Overview & Assembly Order...Page 3 2. Assembling the Structural Components Page 4-11 3. Power, Data, Power Poles and Cable Floor Boxes.Page 12-17 4.
More informationThank you for purchasing out product! *Please read these instructions and follow them step by step. *
Page 1 of 7 AD17 AA DS 4 X 16 T12 Thank you for purchasing out product! *Please read these instructions and follow them step by step. * STEP 1. Slide two support posts (REF. # 24) into the two outside
More informationA59 APD & A86 CPD 5'X 16' SW ALUMINUM PORTA-DOCK
Page 1 of 5 PORTA-DOCK, INC. A59 APD & A86 CPD 5'X 16' SW ALUMINUM PORTA-DOCK *For Beige Decking Add the Letter B to model* Thank you for purchasing our product! *Please read these instructions and follow
More informationIMPULSE G2/PULSE STATIC BRIDGE & RETURN MODULE. Drill. Desk Connecting. Outside by fastening the supplied wood screws from the HK-67 kit through the
PART # 1608990 STATIC BRIDGE & RETURN MODULE 1. This sheet covers the steps to install a static bridge or return module with the FX no hinged access panel back option to a height adjustable freestanding
More informationA MULTI-PURPOSE LOFT THAT CAN BE USED FOR SLEEPING, STORAGE, AND FREEING UP SPACE (Supports 200 lbs max) DIFFICULTY: 6/10
A MULTI-PURPOSE LOFT THAT CAN BE USED FOR SLEEPING, STORAGE, AND FREEING UP SPACE (Supports 200 lbs max) DIFFICULTY: 6/10 CAUTION The instructions are only a guide, and should be followed by individuals
More informationNewHeights Presidente Reception Assembly Instructions Warranty: raproducts.com/warranty
NewHeights Presidente Reception Assembly Instructions Warranty: raproducts.com/warranty Failure to comply with or observe all assembly, safety, and operation instructions and warnings regarding use of
More informationSeries 4 HV Single Monitor Lift Assembly Instructions
6703 Zinser Street Schofield, WI 54476 6/13/17 Series 4 HV Single Monitor Lift Assembly Instructions Read all the instructions before beginning. Hardware Pack # 53368 Page1 OF 6 Tools Required for Assembly:
More informationTechBench Installation Manual
Manual Table of Contents TechBench Overview....2 Bench Assembly Linear,36 (914,4mm) Wide 96 (2438,4mm) Wide 3,4,5,6,7 Bench Assembly Linear,24 (609,6mm) Wide 30 (762mm) Wide..8,9 Bench Assembly Corner
More informationInstalling the Profile Privacy Panel. Assemble top mounting bracket. Prerequisites. Tools
Installing the Profile Privacy Panel Complete these instructions to install the Profile Privacy Panel. Privacy panels are available in various heights to match tiers and include mounting hardware for slat
More informationLinear Hook- on Worksurfaces
Linear Hook- on Worksurfaces Linear Hook-On Worksurfaces come in three depths and seven lengths. Different worksurfaces have different reqirements for installation that are outlined below. 27 inch deep
More informationInstructions for Bed Assembly
Instructions for Bed Assembly 1. Platform Ends (2) 2. Mattress Slats (11-12) 3. Platform Center 4. Platform Sides (2) 5. Safety Rails (2-8) 6. Corner Supports (smaller than pictured) 7. Long Cross Bar
More informationPROFILE Flat Panel Console System Installation Manual
PROFILE Flat Panel Console System Installation Manual Table of Contents Page Introduction... 2 Important Safety Information...3, 4 Installation Overview... 4, 5, 6 Single Sided/Single Unit... 7 Double
More informationInstructions for Bed Assembly
Instructions for Bed Assembly 1. Platform Ends (2) 2. Mattress Slats (11-12) 3. Platform Center 4. Platform Sides (2) 5. Safety Rails (2-8) 6. Corner Supports (smaller than pictured) 7. Long Cross Bar
More informationa.k.a. casegoods instructions
a.k.a. casegoods instructions a a.k.a. workwall installation IMPORTANT NOTES Failure to install product according to installation instruction will result in loss of warranty. Tools required for assembly
More informationCTTR Tire Rack Required tools
CTTR Tire Rack Required tools Torque wrench, ratchet, 9/16 socket, tape measure, and square edge. ASSEMBLY REQUIREMENTS *Torque all T-bolt nuts to 35-40 foot pounds. Failure to follow the assembly instructions
More informationALL SEASON PATIO COVER
ALL SEASON PATIO COVER 61 Where the All Season Patio Cover is to be attached to the home, create a level line showing where the top of the mounting rail is to be located. Install each section with the
More informationModular Furniture LMS. Technical environment systems Installation manual
Modular Furniture LMS Technical environment systems Installation manual Technical Environment Systems INSTALLATION MANUAL Table of Contents INTRODUCTION Full Frame, Open Frame & Upright Assembly...A Foundations...B
More informationINSTALLING YOUR NEW SPRING LIFT ARM KIT
INSTALLING YOUR NEW SPRING LIFT ARM KIT 1. Measure the distance that the roof is to be raised. [If your lift system is completely non-functional, you will need to calculate or estimate this distance as
More informationAssembly Instructions
Laminate/Phenolic & 1 Pc Butcherblock Tops Before you begin, please make sure all parts and proper quantities are included. (See on next page) Any parts damaged during shipment must be reported within
More informationTechnical Environment Systems INSTALLATION MANUAL
Technical Environment Systems INSTALLATION MANUAL Technical Environment Systems INSTALLATION MANUAL Table of Contents INTRODUCTION Full Frame, Open Frame & Upright Assembly...A Foundations...B Mobile &
More informationHover. Installation Instructions. Raised Panel. Version
Installation Instructions Version 8-2-17 Raised Panel Table of Contents Page Raised Panel Trough 3-13 Platform Trough 14-20 Platform 120 Degree Trough 21-24 Electrical 25-28 Type A Electric Bases 29-31
More informationEquipment, Inc. Time required: Less that 30 minutes. Load capacity of this truck is 800 lbs. Never exceed rated capacity! Avoid top-heavy loads.
Equipment, Inc. Thank you for buying this North Star Truck. It has been engineered to ship quickly and inexpensively by UPS and requires assembly. When put together, you will have a sturdy, very versatile
More informationbridges Installation Manual
bridges Installation Manual 0 OHSAS 800:007 CGSB #0HS-009 ISO 900:008 CGSB #96- ISO 00:00 CGSB #EMS-00 Global Contract Inc. 6 Petrolia Road North York, Ontario, MJ X8 Visit us on the Internet at globalcontract.com
More information27693 Trend Podium Desk
1 27693 Trend Podium Desk Assembly Instructions #27693 Trend Podium Desk Hardware List Part Drawing Description Qty P-1 Table Top 1 EA Part Drawing Description Qty A Screw M6 X 15mm 13 EA B Screw M6 X
More informationSAN213 Instruction Manual
SAN213 Instruction Manual Scan here to view product demo and install videos or visit san.us/105 Milestone AV Technologies 6436 City West Parkway Eden Prairie, MN 55344 USA Customer Service Americas: 800-359-5520
More informationASSEMBLY INSTRUCTIONS RIGHT & LEFT HAND "J" TABLE
ASSEMBLY INSTRUCTIONS RIGHT & LEFT HAND "J" TABLE (1) COMPONENT LIST FOR RIGHT & LEFT HAND "J" TABLE NOTE: Please count and inspect all pieces before disposing of any carton or packing materials. 24" x
More informationAssembly Instructions
InTandem Table System November 20 InTandem Table System - Worksurface #4 x/" 4 wood screw power beam Tools Provided T-0 Extended Torx Driver T-25 Torx Driver Additional Tools Required Soft protective
More informationOXYGEN INSTALLATION. Revision date
12345 1 Hardware List 12345 Flat head wood screw #9 x 7/8 long with #2 Phillips drive, silver Used to attach surfaces and end panels Hex set screw ½-13 x 2 long with 1/4 hex drive, black Used on Legs Hex
More informationUP tables & worksurfaces
UP tables & worksurfaces (2-leg) Installation and User Instructions National Office 216-898-0080 Page 1 Step 1: INSTALL FEET AND MOUNTING BRACKETS TO LIFTING COLUMNS Use the provided machine screws. Fasten
More informationFLAT PANEL CART WITH OR WITHOUT A PULL OUT SHELF
FP42UL FP60UL FP42MUL FP60MUL FLAT PANEL CART WITH OR WITHOUT A PULL OUT SHELF WARNING: FP42 carts are intended to hold monitors up to 75 lbs and FP60 carts are intended to hold monitors up to 100 lbs.
More informationWorksurfaces & Supports
SIN 711-1/2 Updated Pricing and Content as of July 1, 2018 WORKSURFACES & SUPPORTS Worksurfaces & Supports Edge Option Edgeband (E) Finished with clean and crisp edges with 1 8" radius edge corners. Edgeband
More informationStag Hanger ASSEMBLY INSTRUCTIONS
Stag Hanger ASSEMBLY INSTRUCTIONS STAG HANGER Recommended Tools Drill with 1/8, 1/4, and 3/8 Drill Bits, 1-1/8 Forstner Bit or 1-1/8 Spade Bit, and Phillips Bit 9/16 and 5/8 Combination Wrench Socket Wrench
More informationKirra Buffet Assembly Instructions
Thank you for your purchase. lease follow the instructions below for correct assembly. C B dowel screw x x6 wedge x4 screw x4 bolt x locking nut x long screw x F screw slide x6 rail x N wheel x4 G slide
More informationChelsea Bedside Table Assembly Instructions
ssembly Instructions Thank you for your purchase. Please follow the instructions below for correct assembly. B F G H dowel x16 I J bolt x locking nut x small x10 K L M N slide rail x1 slide rail x1 P slide
More informationOxford Stalls Installation Instructions
Oxford Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 8/15/17 Before You Start Typical stall sizes are 10 x 10, 12 x 12 or
More informationRiff Tables RIFF-NIC, BAR HEIGHT AND TENNIS TABLE ASSEMBLY INSTRUCTIONS
Riff Tables RIFF-NIC, BAR HEIGHT AND TENNIS TABLE ASSEMBLY INSTRUCTIONS 84" & 72" LONG RIFF TABLE COMPONENTS Top QTY 2 Leg Assembly 2 3 Support Assembly 4 Cross Rail 5 Brace 2 6 000599/Leveler 4 7 #8 x
More informationCustomer Notice: Congratulations again on your SawStop purchase, and thank you! -SawStop Tualatin, OR
Customer Notice: Congratulations on the purchase of this Sliding Crosscut Attachment. As the owner of a SawStop saw, you are familiar with our high standards for quality, fit and finish. Different from
More informationPixMate Flat Panel Mount Cart PM7UL-47JF
PixMate Flat Panel Mount Cart PM7UL-47JF Form E-467 ev. 10/10 MONITO WEIGHT OF 70 lbs. 145 lbs. Caution: The user of this product should exercise caution when moving the PixMate Cart. Any sudden stop could
More informationINSTALLING INVISIRAIL GLASS PANELS POST INFORMATION... 2 PRE-INSTALLATION... 2
Contents POST INFORMATION... 2 PRE-INSTALLATION... 2 STEP A1: MEASURING FOR INVISIRAIL CUSTOM GLASS PANELS (skip if using Standard Sized Panels)... 2 STEP A2: GATHER ADDITIONAL TOOLS/SUPPLIES... 2 STEP
More informationINSTRUCTION SHEET. PIECE INVENTORY - MOBILE BASES Refer to the diagram for part identification.
INSTRUCTION SHEET D2260 HEAVY-DUTY MINI-MOBILE BASE D2057 HEAVY-DUTY MOBILE BASE D2058 SUPER HEAVY-DUTY MOBILE BASE D2259 EXTENSION KIT FOR D2260/D2057 D2246 EXTENSION RAIL KIT FOR D2058 This Shop Fox
More informationMY-HITE CORNER ADJUSTABLE TABLE
081717 MY-HITE CORNER ADJUSTABLE TABLE C-LEG OPTION Model Number : FCNAHBC FRIANT & ASSOC. 4901 E.12 STREET OAKLAND, CA 94601 T:510.535.5113 FAX:510.535.5237 www.friant.com/systems/my-hite Please Read
More informationMY-HITE ADJUSTABLE TABLE
081717 MY-HITE ADJUSTABLE TABLE Model Number : FSQAHTB FRIANT & ASSOC. 4901 E.12 STREET OAKLAND, CA 94601 T:510.535.5113 FAX:510.535.5237 www.friant.com/systems/my-hite Please Read Instructions Before
More informationContour Hanger ASSEMBLY INSTRUCTIONS
Contour Hanger ASSEMBLY INSTRUCTIONS CONTOUR HANGER Recommended Tools Drill with 1/8, 1/4, and 3/8 Drill Bits, 1-1/8 Forstner Bit or 1-1/8 Spade Bit, and Phillips Bit 9/16 and 5/8 Combination Wrench Socket
More informationIndustrial Hanger ASSEMBLY INSTRUCTIONS
Industrial Hanger ASSEMBLY INSTRUCTIONS INDUSTRIAL HANGER Recommended Tools Drill with 1/8, 1/4, and 3/8 Drill Bits, 1-1/8 Forstner Bit or 1-1/8 Spade Bit, and Phillips Bit 9/16 and 5/8 Combination Wrench
More informationAssembly Instructions Above Worksurface Riser Shelf Systems and Back / End Stops
Assembly Instructions Above Riser Shelf Systems and Back / End Stops Back Stops and End Stops Adjustable Riser Shelves Instrument Riser Shelves Stationary Riser Shelves IMPORTANT PLEASE READ THESE INSTRUCTIONS
More informationIsland Wood Range Hood
Island Wood Range Hood Patent Pending Important Notes Always read the instructions completely and carefully before beginning assembly. Remove and check contents for damage and/or missing parts. Keep the
More informationGambrel Barn Construction Manual 8x8 through 16x24 Units
Gambrel Barn Construction Manual 8x8 through 16x24 Units Tools Needed: Cordless drill (12V or higher) #2 square drive bit Hammer 6 step ladder Tape measure Square utility knife w/ blade & hook blade Little
More informationSuper Tube Spiral Slide Instructions
Super Tube Spiral Slide Instructions Super Tube Spiral Slide 2 SECTIONS WITH OVERLAPPING FLANGES 3 SECTIONS WITHOUT OVERLAPPING FLANGES 3-1/2 LAG SCREW W/WASHER 5/16 X 1 BOLT W/WASHERS AND LOCK NUT 5/16
More informationπ H-4408 ALUMINUM BLEACHERS 5-ROW x 15' PARTS uline.com TOOLS NEEDED
π H-4408 1-800-295-5510 uline.com ALUMINUM BLEACHERS 5-ROW x 15' TOOLS NEEDED Square Tape Measure Rivet Gun 3/16" Drill Bit 1/2" Wrench Socket Wrench 1/2" Deep Well Socket #2 Phillips Bit Rubber Mallet
More informationPack Mount Instructions:
Pack Mount Instructions: STEP 1 Mounting upright base to desired surface If mounting to a surface with an accessible backside (such as a thin walled container): Option 1 Discard the Round Mounting Disk
More informationINSTALLATION MANUAL VERITY. friant.com/verity
INSTLLTION MNUL VERITY friant.com/verity 2 VERITY INSTLLTION MNUL General Information... 4 Safety & Support... 5 Installation Tools... 6 Staging & Installation... 7 Stand lone Units Single-Sided Structure...
More informationTWIG Hanger ASSEMBLY INSTRUCTIONS
TWIG Hanger ASSEMBLY INSTRUCTIONS TWIG HANGER Recommended Tools Drill with 1/8, 1/4, and 3/8 Drill Bits, 1-1/8 Forstner Bit or 1-1/8 Spade Bit, and Phillips Bit 9/16 and 5/8 Combination Wrench Socket Wrench
More informationAssembly Instructions
1 BLT-27565 FDB Stand Assembly Instructions BLT-27565 FDB Stand Part Drawing Description Qty Part Drawing Description Qty P-1 Top Shelf 1 EA P-10 LL Lower Leg 1 EA P-11 Middle Shelf 1 EA P-2 L-Upper Leg
More informationIMPULSE G2/PULSE STATIC BRIDGE & RETURN MODULE. Drill. Desk Connecting. Outside by fastening the supplied wood screws from the HK-67 kit through the
PART # 1608990 STATIC BRIDGE & RETURN MODULE 1. This sheet covers the steps to install a static bridge or return module with the FX no hinged access panel back option to a height adjustable freestanding
More informationInterra Installation Manual
Interra Installation Manual Instructions to install the Friant Interra panel system Friant & Associates, LLC Table of Contents Getting Started Introduction... 3 General Tools, Staging & Safety... 4 Before
More informationCellar Hanger ASSEMBLY INSTRUCTIONS
Cellar Hanger ASSEMBLY INSTRUCTIONS CELLAR HANGER Recommended Tools Drill with 1/8 and 1/4 Drill Bits, 1-1/8 Forstner Bit or 1-1/8 Spade Bit, and Phillips Bit 9/16, 7/16, and 5/8 Combination Wrench Socket
More informationSelect Lab Adjustable Height Workstation
Assembly Instructions Select Lab Adjustable Height Workstation Mobile version is shown. Also available without casters. Contents Important User Information.............................. 2 Safety Precautions....................................
More information