media:scape HDVC Wall Mount

Size: px

Start display at page:

Download "media:scape HDVC Wall Mount"

Florence Foster
5 years ago
Views:

1 Dual Shroud media:scape HDVC Wall Mount Single Shroud CAUTION Quad Shroud FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY. Triple Shroud Read the entire Assembly Direction before beginning installation or assembly. Building construction varies greatly and is outside Steelcase's control. The Building's Engineer of Record is responsible for the design of studs, backing, reinforcement, supporting members etc. which the units are attached to and must verify the adequacy of the mounting hardware. These instructions and any hardware provided by Steelcase are for convenience only and are not an indication of what may be required by your local Code. Dual Shroud with Bridge & Codec Case Attachment Total load of each monitor bracket (monitor + monitor bracket) MAXIMUM WEIGHT LBS (92 kg.) 3/32", 1/8", 3/16" HEX DRIVE The building owner or designated agent is responsible for verifying that the installation is in compliance with all local Codes and regulations. Topic Table of Contents Page Standard Wall Mount Shroud 2 Codec Wall Mount Shroud 7 Bridge Attachment 10 If you have a problem, question, or request, call your local dealer, or Steelcase Line 1 at 888.STEELCASE ( ) for immediate action by people who want to help you. (Outside the U.S.A., Canada, Mexico, Puerto Rico, and the U.S. Virgin Islands, call: ) Or visit our website: Steelcase Inc. Grand Rapids, MI U.S.A. Printed in U.S.A. WARNING: All electrical installations should be done by a qualified person in accordance with codes and regulations applicable at the installation site. PDR Panel Display Mount 11 Codec Case Attachment 12 Seismic Wall Mount Shroud 14 Shroud Camera Mount 18 Totem Camera Mount 18 Shroud Hole Locations and 19 Additional Dimensions Page 1 of 19

2 1/4" GAP Standard Wall Mount Shroud NOTE: Unit comes assembled. You must first remove all tubing from the shroud. For the top tube, loosen the top screws a 1/4" and slide screws out of the keyhole slots. For the bottom tube, remove screws completely to remove tubing. NOTE: The installation of the horizontal wall mount depends on there being an adequate wall to support the weight of the shroud and monitor assembly. This procedure is specifically for mounting to a metal stud wall that has a maximum of 24" between centers and minimum metal guage of 25 (.017" thick). The position of the shroud relative to the studs must conform to steps 4 & 5. Once location is determined, installation can proceed according to the following steps. Standard Wall Mount Shroud (If installing with a bridge, see page 10 before continuing. For additional shroud dimensions, see page 19.) 1 3-7/16" TO C L OF SLOT 1-9/16" C L TO CL NOTE: Mounting hardware is to be specified/verified by the Building's Engineer of Record. Install fasteners per the hardware manufacturer's instructions. CAUTION: Be careful not to cut/drill through any wires that may be hidden in the wall. 1. Determine height of shroud from floor. Shroud height Dim. X (See chart on page 3) 1-9/16" C L TO CL Page 2 of 19

3 3 2. Mark the top horizontal lines using a level. 3. Find and mark all stud locations near desired position on the wall. Determine edges of studs. 4. Adjust horizontal tube position to have most possible hole locations line up with the center of a stud in the wall (4a). On sizes that require two (2) top tubes, make sure to butt tubes tight together (4b). 5. The attachment slots on both ends need to be structurally attached to the building wall. One of the end attachment slots need to be structurally attached to a stud, while the other end also needs to be structurally attached, if not by a stud then by another structurally appropriate attachment method depending on the wall construction. 2 Size 32 Sgl 32 Dbl 32 Triple 32 Quad 42 Sgl 42 Dbl 42 Triple 42 Quad 46 Sgl 46 Dbl 46 Triple 55 Sgl 55 Dbl 55 Triple 65 Sgl 65 Dbl 65 Triple 42 Dbl 42 Triple 46 Dbl 46 Triple Dim X Dim Y Dim Z Standard and Seismic 14-7/8" 14-7/8" 14-7/8" 36-1/2" 19-1/8" 19-1/8" 19-1/8" 45-3/8" 22" 22" 22" 26-5/8" 26-5/8" 9-3/4" 9-3/4" 9-3/4" 9-1/2" 9-3/4" 14" 9-3/4" 10-1/4" 15" 12" 15" 12-1/2" 11-5/8" 14-5/8" 12-1/8" 15" 26-5/8" 12-1/2" 13-3/4" 32" 32" 32" 19-1/8" 19-1/8" 22" 22" 9-3/4" 9-3/4" Codec 8" 8" 12-5/8" 11-3/4" 10-3/4" 15" 12" 11-5/8" 14-7/8" Shroud Ht. 23-3/8" 23-3/8" 23-3/8" 45" 27-5/8" 27-5/8" 27-5/8" 53-7/8" 30-1/2" 30-1/2" 30-1/2" 35-1/8" 35-1/8" 35-1/8" 40-1/2" 40-1/2" 40-1/2" 27-5/8" 27-5/8" 30-1/2" 30-1/2" ON A STUD 5-1/2" REF. 2-1/2" 5-1/2" REF. ON A STUD 8" TYPICAL WALL Dim. Z Dim. Y STRUCTURALLY APPROPRIATE ATTACHMENT OVERALL DEPTH 5-1/2" (STD.) 7" (CODEC) 1" (STD.) 2-1/2" (CODEC) 15/32" 1-9/16" 3-15/32" 4a C L C L Dim. X SHROUD HEIGHT C L X 4b STUD FLOOR LINE 5 Page 3 of 19

4 6a 6b 6. Mark hole locations (studs and/or drywall locations) (6a) and attach tube accordingly depending on the wall construction that is at that location (6b). NOTE: Fasteners are not provided. Fasteners must be used in both top & bottom holes of each tube. 7. Verticals are positioned using the edge of the top horizontal tube as a guide. Position tight into corner (7a) and use a level or large carpenters square to plumb vertically (7b). 8. Mark center of horizontal slots of vertical brackets. 9. Attach vertical brackets to wall accordingly depending on the wall construction that is at that location. NOTE: Fasteners are not provided. TOP HORIZONTAL TUBE 7a 7b VERTICAL Page 4 of 19

5 10 Front View 10. Measure across corners of verticals to check for squareness before securing to wall. VERTICAL 11. A bottom horizontal tube is required for duals that are greater than 80" wide (42" product and larger) and for all triples & quads. The bottom horizontal tube is included when it's required and does not need to be ordered seperately. NOTE: A bottom horizontal tube is not required for all singles. 12. Mark/draw line from the bottom of the two (2) verticals. 13. Determine and mark the centerline between the two verticals on the wall. VERTICAL MARK LINE FROM THE BOTTOM OF THE TWO VERTICALS Determine and mark the centerline on the narrow tube. C L 15. Position bottom horizontal tube aligning the bottom of the tube with horizontal line (while level) and centerline marks, while marking the attachment hole locations on the wall. 14 VERTICAL MARK LINE FROM THE BOTTOM OF THE TWO VERTICALS 15 C L Page 5 of 19

6 16 1/4" GAP KNOCKOUT NOTE: If knockout needs to be removed for camera wires, insert flat-bladed screwdriver and rotate. 16. Attach bottom horizontal tube to the wall accordingly depending on the wall construction that is at that location. NOTE: Fasteners are not provided. Fasteners must be used in both top & bottom holes of each tube. 17. Verify all colored washers at all keyhole slots on the upper tube with provided fasteners. Leaving approximately 1/4" gap from tube. TIP: Knockout appropriate wire management locations, determined by the A.V. integrator before continuing b FASTENER KEYHOLE SLOT 18c 18d 18. Attach shroud by lifting keyhole slots over protruding fasteners on the top tube. 18a 20b 19. Check for alignment of all fasteners and adjust as necessary prior to securing all shroud fasteners in place. 20a 20. Secure shroud using provided screws in all locations. Top & bottom tubes (20a) and verticals (20b). 20b SHROUD Page 6 of 19

7 Codec Wall Mount Shroud 1/4" GAP NOTE: Mounting hardware is to be specified/verified by the Building's Engineer of Record. Install fasteners per the hardware manufacturer's instructions. 2 3a 1. Perform steps 1 through 6 of the "Standard Wall Mount Shroud" on pages 2 and 3. NOTE: Make sure to pay attention to the tube orientation. The tab at the end of the tubes go toward the inside as shown. TEMPLATE 2. Verify provided fasteners are mounted at keyhole slots on upper tube. Leaving approximately a 1/4" gap away from the tube. 3. Position bottom horizontal tube by hanging the provided templates. Use upper hole for a shroud height of 27-5/8" (42" product) and lower hole for a shroud height of 30-1/2" (46" product) (3a). Use a level or large carpenters square to plumb vertically, while making sure the bottom horizontal tube is pressed tightly to wall (3b). 3b BOTTOM HORIZONTAL TUBE Page 7 of 19

8 4 4. Measure across corners of verticals to check for squareness. 5. Mark all hole locations on the bottom horizontal tube. 6. Verify squareness. Attach bottom horizontal tube to wall, accordingly depending on the wall construction that is at that location. NOTE: Fasteners are not provided. Fasteners must be used in both top & bottom holes of each tube. 5 CODEC BOX Z-BRACKET FOR CODEC BOX 7. Remove template brackets. 8. Locate and install spring clips on tabs on both ends of both horizontal tubes. 9. Locate & install z-brackets for codec box. Position as required, so codec box can slide in from the desired side. NOTE: Fasteners are not provided. TIP: Knockout appropriate wire management locations, determined by the A.V. integrator before continuing. Install/place wires for codec unit. 8 KNOCKOUT TAB SPRING CLIP NOTE: If knockout needs to be removed for camera wires, insert flat-bladed screwdriver and rotate "-12" Page 8 of 19

9 10b 10c KEYHOLE SLOT 10d 10. Attach shroud by lifting keyhole slots over protruding fasteners on the top tube. FASTENER 11. Check alignment of all fasteners and adjust as necessary prior to securing all shroud fasteners in place. 12. Secure shroud, using provided screws, to all locations (top and bottom tubes). 13. Snap in the perforated vertical covers over clips. TIP: Lock features are provided for use with an aftermarket lock such as Kensington. 10a SHROUD Perforated vertical covers let heat dissipate from the codec unit and allows access to hardware for services. VERTICAL COVER Page 9 of 19

10 3-5/16" TO C OF SLOT L 1-9/16" C L TO CL Bridge Attachment SHROUD HEIGHT NOTE: Not for seismic or codec versions of shrouds. 5-1/16" 1. In order to attach the bridge to the table it is important that shrouds be positioned relative to media:scape table heights. Lounge Height = 23-1/8" from floor. Desk Height = 28-5/8" from floor. LOUNGE HT /8" DESK HT /8" STANDING HT /8" 3a 3b Standing Height = 38-1/8" from floor. 2. Follow steps 1 through 10 of the "Standard Wall Mount Shroud" on pages 2 through 5. BRIDGE 3. Attach bridge behind shroud and secure in place in the vertical slots with two (2) 5/16-18 x 3/4" long screws Slide table into position and level. 5. Align and attach bridge holes with inserts in worksurface. This will level bridge to the correct height on the shroud Secure bridge/shroud holes in slot from step 3. Page 10 of 19

11 7 8 PYRAMID COVER 7. After managing necessary wires, install wire cover by securing in place using two (2) 5/16-18 x 7/8" button head screws. NOTE: Wire cover not provided, ordered seperately. 8. Install pyramid covers with necessary 5/16-18 x 7/8" button head screws. (Reference media:scape installation manual, if necessary.) PDR Panel Display Mount 1. Locate the PDR package & hardware bag. 2. Choose from the three (3) possible positions, depending on the size and make of the television. Install wall mount bracket from PDR kit, with fasteners provided in Steelcase hardware bag (not from kit), to the shroud. Note the flange orientation of the wall mount bracket. 3. See installation direction 'PDM120THN Panel Mount Display' that is inside the panel display mount box. Install display brackets, plastic spacers (optional), gravity lock brackets provided in Steelcase hardware bag and adjust the lateral movement per the manufacturer's specifications. 5/16-18 X 7/8" BUTTON HEAD SCREW WIRE COVER POSITION #1 POSITION #2 POSITION #3 5/16-18 X 7/8" BUTTON HEAD SCREW 2 SHOWN IN POSITION #2 Total load of each monitor bracket (monitor + monitor bracket) MAXIMUM WEIGHT LBS (92 kg.) FLANGE UP Page 11 of 19

12 Codec Case Attachment 2a NOTE: Be careful not to pinch any wires that may already be installed through this area. 1. Align the four (4) holes on the bridge with the four (4) holes on the codec case and attach with four (4) 5/16-18 x 3/8" long fasteners provided. The perforated cover must be removed for the 5-1/2" thick version and does not need to be removed for the 2-1/2" version. 2. To remove the perforated codec cover, remove two (2) screws at the top (2a) and rotate the top outwards (2b). CODEC CASE BRIDGE 5/16-18 x 3/8" LONG FASTENER 1 2b Perforated cover lets heat dissipate from the codec unit and allows access to hardware for services. Page 12 of 19

13 3 3. Install strap by feeding through either set of slots so that the connections points are accessible from the front. 4a TIP: Lock features are provided for use with an aftermarket lock such as Kensington. 4. To install the codec cover, position the two (2) hooks on the two (2) tabs (4a) and rotate the top upwards (4b). Tight fit (resistance) is to reduce rattling. Secure in place with two (2) #10 x 1/4" long screws (provided) (4c). NOTE: Modifications may be necessary to retrofit totem bridges. Mark and drill accurately to dimensions shown. After drilling, tap the four (4) holes 5/16-18 thread. Side View 4b Side View 4c 8" 5-1/8" 3" 2-5/8" HOOK TAB Page 13 of 19

14 Seismic Wall Mount Shroud Front View 1. Perform steps 1 through 10 of the "Standard Wall Mount Shroud" on pages 2 through 5. VERTICAL 2. Position bottom horizontal tube tight into corners of both verticals Adjustments may be needed to the verticals to make sure the bottom horizontal tube fits tight. C L 4. Measure across corners of verticals to check for squareness before securing to wall. 4 C L Page 14 of 19

15 5 5. Mark all hole locations on the bottom horizontal tube. 6. Attach bottom horizontal tube accordingly depending on the wall construction that is at that location (6a). On sizes that require two (2) bottom tubes, make sure to butt tubes tight together (6b). NOTE: Fasteners are not provided. Fasteners must be used in both top & bottom holes of each tube. 7. On sizes that require two (2) bottom tubes: Check the spacing of the top tube to the bottom tube at the center seam (7a). Make sure the spacing is equal at both ends of the tube (7b). 6a 7a 6b 7b Page 15 of 19

16 1/4" GAP 8 8 KNOCKOUT NOTE: If knockout needs to be removed for camera wires, insert flat-bladed screwdriver and rotate. 8. Verify all colored washers at all keyhole slots on the upper tube with provided fasteners. Leaving approximately 1/4" gap from tube. TIP: Knockout appropriate wire management locations, determined by the A.V. integrator before continuing b KEYHOLE SLOT 9. Attach shroud by lifting keyhole slots over protruding fasteners on the top tube. 9a FASTENER 9c 9d SHROUD Page 16 of 19

17 10. Check for alignment of all fasteners and adjust as necessary prior to securing all shroud fasteners in place. 11a 11. Secure shroud using provided screws in all locations. Top & bottom tubes (11a) and verticals (11b). 11a 11b 11a 11a 11a 11a 11b Page 17 of 19

18 SHROUD CAMERA SHELF 1a Shroud Camera Mount 1. To install a shroud camera shelf, loosen set screw (by turning counter-clockwise) enough to lower shelf onto top of shroud (1a). On back of shelf, using an Allen wrench tighten set screw by turning clock-wise (1b). Mount camera on top of shelf by installing camera mount screw on bottom of shelf and turning clock-wise (1c). NOTE: DO NOT over tighten set screw. Totem Camera Mount 2. To install a totem camera shelf, loosen set screw (by turning counter-clockwise) enough to slide shelf onto totem (2a) so that bracket underneath the shelf engaged with totem (2b). On top of shelf, using an Allen wrench tighten set screw by turning clock-wise (2c). Mount camera on top of shelf by installing camera mount screw on bottom of shelf and turning clock-wise (2d). NOTE: DO NOT over tighten set screw. 1b 2a TOTEM CAMERA 2b CAMERA SHELF TOTEM BRACKET TOTEM SHELF 2c TOTEM 1c 2d Page 18 of 19

19 D (Overall Width) D (Overall Width) Shroud Hole Locations: A A Use chart to aid in positioning of any holes that maybe required in the wall behind the shrouds. NOTE: Reference PDR Panel Display Mount (page 11) for the possible positions of the wall mount bracket that could interfere with anything behind the shroud. B B Single Monitor B D (Overall Width) C Dual Monitor B Style No. Single Monitor MTSWS32 MTSWS42 MTSWS46 MTSWS55 MTSWS65 Dual Monitor MTSWD32 MTSWD42 MTSWD46 MTSWD55 MTSWD " 13.80" 15.25" 17.55" 20.25" 11.70" 13.80" 15.25" 17.55" 20.25" 17.56" 22.21" 24.51" 28.16" 32.66" 17.56" 22.21" 24.61" 28.16" 32.66" Dual Monitor with CODEC Case MTSWD42C MTSWD46C Triple Monitor MTSWT32 MTSWT42 MTSWT46 MTSWT55 MTSWT " 15.25" 11.70" 13.80" 15.25" 17.55" 20.25" 22.21" 24.61" 17.56" 22.21" 24.71" 28.16" 32.66" Triple Monitor with CODEC Case MTSWT42C MTSWT46C Quad Monitor MTSWQ32 MTSWQ42 Dim. A Dim. B Dim. C Dim. D 13.80" 22.21" 15.25" 24.71" 11.70" 17.56" 13.60" 22.21" NA NA NA NA NA 32.43" 41.73" 46.12" 53.62" 62.12" 41.72" 46.12" 32.43" 41.73" 46.12" 53.62" 62.12" 41.73" 46.12" 32.43" 41.73" 35.00" 44.00" 48.50" 56.00" 65.00" 67.00" 86.00" 95.00" " " 86.00" 95.00" 99.50" " " " " " " 67.00" 86.00" B C Triple Monitor 10-1/2" Hole pattern C 5" 2-1/2" B B C A D (Overall Width) Quad Monitor B A A Page 19 of 19

FlexFrame - Storage Components and Skins

FlexFrame - Storage Components and Skins 1/4 Square Drive Ball-Point Hex-Bit Socket 1/8 Short Hex, 1-1/2 Overall Length McMaster Part # 54075A44 Table of Contents Topic Page Storage Components 2 General