Opus Base Unit Assembly
|
|
- Mae Edwards
- 6 years ago
- Views:
Transcription
1 Opus Base Unit Assembly 5/16" NOTE: All cam locks need to be rechecked to confirm they are tight before installation. Gaps could result if not completely tightened and effect assembly. 2 Foot Scrap Board Padded Saw Horses If you have a problem, question, or request, call your local dealer, or Steelcase Line 1 at 888.STEELCASE ( ) for immediate action by people who want to help you.. (Outside the U.S.A., Canada, Mexico, Puerto Rico, and the U.S. Virgin Islands, call: ) Or visit our website: Steelcase Inc. Grand Rapids, MI U.S.A. Printed in U.S.A. NOTE: It is required to have two (2) people to install this base unit assembly. Wet Sponge Page 1 of 12
2 Assembling the Base Assembly NOTE: 24" Base Assembly shown. PIN CAM BACK TWO (2) HOLES INDICATE BOTTOM OF UNIT 1. Lay back assembly onto two (2) padded saw horses. Insert pins and wood dowels into the holes of the back assembly as shown. Before installing the wood dowel, wet the dowel with a wet sponge to activate the adhesive on the surface of the dowel. NOTE: Make sure the arrow located on each cam is pointed toward the hole that will accept the pin. WOOD DOWEL PADDED SAWHORSE Page 2 of 12
3 CANOPY BACK 2b 2c 2. Align the canopy assembly to the back assembly (2a). TWO (2) HOLES INDICATE BOTTOM OF UNIT Make sure holes on the canopy assembly accept the pins and dowels on the back assembly (2b). 2d Draw each cam lock, in a clockwise direction, into the center of the cam 0º to 75º (no tightening occurs at this point). The cam lock range for tightening is 75º to 195º. Hand tighten until a rigid tensioning is achieved in both cam locks (2c). BACK Install canopy straps between the canopy assembly and the back assembly with two (2) #8-15 x 5/8" pan head wood screws per strap as shown (both sides) (2d). CANOPY STRAP Install eight (8) shelf support pins onto the canopy assembly (2e). 2e 2a CANOPY Page 3 of 12
4 PIN 3. Insert pins and wood dowels into the holes of the toeboard assembly as shown. Before installing the wood dowel, wet the dowel with a wet sponge to activate the adhesive on the surface of the dowel. WOOD DOWEL NOTE: Make sure the arrow located on each cam is pointed toward the hole that will accept the pin. TOEBOARD Page 4 of 12
5 4b TOEBOARD 4. Align the toeboard assembly to the back assembly (4a). 4a Make sure holes on the toeboard assembly accept the pins and dowels on the back assembly (4b). 4c Draw each cam lock, in a clockwise direction, into the center of the cam 0º to 75º (no tightening occurs at this point). The cam lock range for tightening is 75º to 195º. Hand tighten until a rigid tensioning is achieved in both cam locks (4c). 4b TOEBOARD 4c BACK Page 5 of 12
6 FOAM TAPE PAPER BACKING 5a 5. Peel paper backing from foam tape (5a). Place foam tape onto back of base unit as shown (5b). Cut excess foam tape when finished. 5b Page 6 of 12
7 6. Stand base unit upright. 7. To prevent the base unit from tipping over, place a scrap board along bottom of base unit (7a). Using a quick clamp, secure the scrap board to the bottom of the base (7b). Secure scrap board with a second quick clamp (7c). 7a SCRAP BOARD 7b QUICK CLAMP 6 7c Page 7 of 12
8 Ganging the Base Units 1. Align second base unit with the first base unit. 2. Make sure the front face of each base unit is flush with each other (2a). Secure the canopy assemblies of both base units together, front to back & top to bottom, using a quick clamp (2b). 1 2a QUICK CLAMP 2b NOTE: DO NOT BOLT BASES TOGETHER! Page 8 of 12
9 3. Make sure the front face of all base units are flush with each other before clamping. Secure the back assemblies of both base units together using quick clamps as shown Page 9 of 12
10 DRILL 5/16" DIAMETER CLEARANCE HOLES 4. Make sure the fronts of the base toeboard assemblies are flush. 5. Drill two (2) 5/16" diameter clearance holes through the canopy assemblies as shown. APPROX. 1-1/4" 5 6. Secure using bolts, washers and nuts as shown. Bolts may be inserted from either side. WASHER BOLT WASHER NUT NOTE: DO NOT BOLT BASES TOGETHER! Page 10 of 12
11 7. Drill four (4) 5/16" diameter clearance holes, per mating units, through the back assemblies as shown Secure using bolts, washers and nuts as shown. Bolt may be inserted from either side. APPROX Repeat steps 1 through 8 if more base units are required. APPROX Remove clamps and add canopy dust covers where appropriate. APPROX APPROX. 20 DRILL 5/16" DIAMETER CLEARANCE HOLE NOTE: DO NOT BOLT BASES TOGETHER! Page 11 of 12
12 NOTE: Clean up all sawdust from floor and canopy before moving units against the wall. 11. Move units up against the wall. 12. Level all units. NOTE: Make sure to push down on the base unit when leveling. A lower storage unit will add this weight and ensure a 90 degree angle in the back of the unit Page 12 of 12
Opus Standard Corner Trim Unit
Opus Standard Corner Trim Unit If you have a problem, question, or request, call your local dealer, or Steelcase Line 1 at 888.STEELCASE (888.783.3522) for immediate action by people who want to help you.
More informationSeries 9000 Panel Door; In-Line, Corner and Permanent Wall Application
Series 9000 Panel Door; In-Line, Corner and Permanent Wall Application 5/32" Drill Bit In-Line Corner Permanent Wall 3/16" Allen Wrench If you have a problem, question, or request, call your local dealer,
More informationPrivacy Wall & Glass Selections Pivot-Hinged Door (For products manufactured after September 14, 2009)
Privacy Wall & Glass Selections Pivot-Hinged Door (For products manufactured after September 14, 2009) 3/16" HEX BIT #2 ACR BIT 3/8" HEX SOCKET Full-Height (No Switch) Transom (No Switch) Full-Height (With
More information434 Cobi Chair - Seat Shell Replacement
434 Cobi Chair - Seat Shell Replacement PROFILE OF HARDWARE FOR CLARITY #8-18 x 1/2" Pan Head Tapping Screw Magnetic Bit Holder M6 x 45mm Wafer Head Screw T-30 Large flat-bladed screwdriver If you have
More information110 and 555 Markerboard, Chalkboard and Tackboard Mounting
0 and 555, Chalkboard and Tackboard Mounting 0 # BIT 0 Splined 0 and 555 Tackboard POWER GRIPS 555 If you have a problem, question, or request, call your local dealer, or Steelcase Line at 888.STEELCASE
More informationPathways Privacy Wall Glass Selections - Sliding Door
Pathways Privacy Wall Glass Selections - Sliding Door #2 ACR BIT 3/16" HEX BIT RAYBO ETCHED GLASS STYLES: Satin Mist PATTERN GLASS STYLES: Waterfall Bamboo Harp Mirage If you have a problem, question,
More informationFlexFrame - Storage Components and Skins
FlexFrame - Storage Components and Skins 1/4 Square Drive Ball-Point Hex-Bit Socket 1/8 Short Hex, 1-1/2 Overall Length McMaster Part # 54075A44 Table of Contents Topic Page Storage Components 2 General
More informationPrivacy Wall Glass Selections - Polished Edge Slider Door
Privacy Wall Glass Selections - Polished Edge Slider Door 3/6" HEX BIT PUTTY KNIFE #2 ACR BIT SUCTION CUP HOLDERS DOOR LEAF: Satin Tempered Clear Tempered LOCTITE 425 SIDE LIGHT ETCHED GLASS STYLES: Satin
More informationAnswer Power Beam and Boundary Screen
Answer Power Beam and Boundary Screen 5/16 MAGNETIC 3/8 If you have a problem, question, or request, call your local dealer, or Steelcase Line 1 at 888.STEELCASE (888.783.3522) for immediate action by
More informationHeight Adjustable Benching End Panel and Utility Pole
Height Adjustable Benching End Panel and Utility Pole Tools required: END PANEL Jig Saw Power Drill END PANEL WITH UTILITY POLE Bit Holder Long #2 Square Drive Bit 5mm Hex Drive Bit UTILITY POLE Level
More informationLarge Case Storage - Counterweights
Large Case Storage - Counterweights Lateral File/Combo Cabinet CAUTION Please refer to the Steelcase Specification Guide for Storage for additional guidance on determining the correct counterweight package.
More informationBOOKCASE WARNING. Illustration 1
Illustration 1 Lower Back Panel Upper Back Panel Cam Connector Illustration 2 Left end Illustration 3 Cam Bolt Adjustable Shelf Left end Left End Panel Bottom/ Center Shelf Connector Cover Right End Panel
More informationUniversal Storage 1-Hi and 1.5-Hi Lateral File Counterweight Package
Universal Storage 1-Hi and 1.5-Hi Lateral File Counterweight Package 1-Hi 18" & 24 Deep Cabinets (pages 2-4) 1.5-Hi 18" & 24 Deep Cabinets Drawer/Drawer or Open/Drawer (pages 5-7) CAUTION Please refer
More informationASSEMBLY GUIDE. Mia Narrow Bookcase
ASSEMBLY GUIDE Mia Narrow Bookcase Components: Upon unpacking your bookcase from it s delivery box, you should have the pieces shown. Follow the steps on the next pages to assemble your new bookcase. Step
More informationPremium Whiteboard and Tackboard Mounting
Premium Whiteboard and Tackboard Mounting #2 BIT If you have a problem, question, or request, call your local dealer, or Steelcase Line 1 at 888.STEELCASE (888.783.3522) for immediate action by people
More informationGroupwork Tables. Table of Contents. Page Topic. Page 1 of Rev G
Table of Contents Page Topic 2-13 T-Legs & s Installation 14 Typical Table Configurations 15 Wire Manager Installation Groupwork Tables To ensure stability and prevent possible injury, standing height
More informationc:scape Shared Tables - Freestanding and Tethered
c:scape Shared Tables - Freestanding and Tethered Furniture should be installed in sequence shown below. 1 2 3 4 5 6 BEAM MID STORAGE DESKING POWER LOW STORAGE PRIVACY THIS INSTALLATION SEQUENCE IS HERE.
More information488 Brody Disassembly Direction
488 Brody Disassembly Direction Lighting (see page 8) Screens (see page ) Backrest (see page 4) " and " BIT HOLDERS Side Surface (see page ) T0, T0, T40 TORX Personal worksurface (see page 6) Caddy (see
More informationCDAS CDAS39 SHELF UNIT
BY CDAS CDAS39 SHELF UNIT 0708 IMPORTANT! Assembly may require the assistance of another person. Before you begin assembly: READ THE DIRECTIONS all the way through one time. This will speed up the process
More informationTopo Freestanding Applications - Private Office
4 3 2 Topo Freestanding Applications - Private Office Combo Wrench If you have a problem, question, or request, call your local dealer, or Coalesse at 1.800.627.6770 Or visit our website: www.coalesse.com
More informationLW36 LAB WORKSTATION IMPORTANT!
BY LW36 LAB WORKSTATION 01/06 IMPORTANT! Assembly may require the assistance of another person. Before you begin assembly: READ THE DIRECTIONS all the way through one time. This will speed up the process
More informationDisplay-Top Apothecary Cabinet. Assembly Instructions. Page 1
Display-Top Apothecary Cabinet Assembly Instructions Page 1 Display-Top Apothecary Cabinet Parts List Please check packaging for all parts and hardware before discarding. Unpack and lay parts on clean,
More informationModular & Hardwired Hub Assembly to "X" and "Y" Posts
Modular & Hardwired Hub Assembly to "X" and "Y" Posts Hardware Package T-Nut Data jack bracket #6 x 1/4" plastite trilobular screw 1/4-20 x 3/4" socket head cap screw #6-32 x 1/4" pan head screw #10-32
More informationWOOD GRAIN 6 SHELF BOOKCASE
HRDWRE 4 - wood dowels 20 - cam 8 - large 12 - shelf pins 4 - adhesive cam covers 20 - cams 8 - brackets Missing hardware? Please call 800.606.6387 for replacements. WLL MOUNTING HRDWRE 2 - small 2 - large
More information487 Cachet Swivel - Base Chair Replace Front Seat Support or Seat
487 Cachet Swivel - Base Chair Replace Front Seat Support or Seat SPECIAL ALLEN WRENCH PROVIDED If you have a problem, question, or request, call your local dealer, or Steelcase Line 1 at 888.STEELCASE
More informationEDGE2 DUAL MONITOR ARM
EDGE2 DUAL MONITOR ARM EDGE2 Rev A 2/17 Model EDGE2-SLV Model EDGE2-BLK Model EDGE2-WHT ASSEMBLY AND ADJUSTMENT EDGE2 DUAL MONITOR ARM PARTS AND TOOLS PLEASE REVIEW these instructions before beginning
More informationTop Closure Kit Accessory for Music Library System
Assembly Instructions Top Closure Kit Accessory for Music Library System Contents Required Tools.....................................2 Installation Requirements............................2 Fasteners -
More informationmedia:scape HDVC Wall Mount
Dual Shroud media:scape HDVC Wall Mount Single Shroud CAUTION Quad Shroud FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY. Triple Shroud Read the entire Assembly
More informationSeries Adjustable Height Tables
Series 7.2 - Adjustable Height Tables Tools required: Power Drill #2 SQUARE DRIVE BIT If you have a problem, question, or request, call your local dealer, or Steelcase Line 1 at 888.STEELCASE (888.783.3522)
More informationThe Archer Bow Press OPERATING INSTRUCTIONS Partridge Woods Elk Rapids, MI
The Archer Bow Press OPERATING INSTRUCTIONS 8203 Partridge Woods Elk Rapids, MI 49629 www.bowforcearchery.com 1 MAINTENANCE AND FINE TUNING Horizontal Pulling Bar The Horizontal Pulling Bar has a break-in
More informationv1.0 ASSEMBLY GUIDE Mia Wide Bookcase
v1.0 ASSEMBLY GUIDE Mia Wide Bookcase Components Upon unpacking your bookcase from it s delivery box, you should have the pieces shown. Follow the steps on the next pages to assemble your new bookcase.
More informationPORTABLE ADJUSTABLE BASKETBALL SYSTEM
Instruction Manual PORTABLE ADJUSTABLE BASKETBALL SYSTEM P A R T S L I S T 5 1/2 and 8 safe play clearance Item Qty Description Item Qty Description A 1 Portable Base Assembly M 4 1/2 Lock Nut B 2 Front
More informationPlease read these instructions before use and keep for future reference
Wardrobe Assembly Guide Allen Key Provided (if required) Philips Screwdriver Required Hammer Required Please read these instructions before use and keep for future reference Caution! Two Person Assembly
More informationSeries 7 AdjusTable Height Tables
Series 7 AdjusTable Height Tables Tools required: #2 Phillips Bit with Extension #2 Square Drive Bit 4mm Hex Drive Bit #3 Phillips Bit If you have a problem, question, or request, call your local dealer,
More informationASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS ITEM No. :Quilty/ 3 A helpful Assembly Video can be found on www.arrowcabinets.com in the Video Section under Quilty Incorrect Correct The turning direction of attaching The arrow
More informationINSTALLATION INSTRUCTIONS VENETIAN 84" SLIDING SHOWER DOOR SYSTEM (180º INSTALLATION)
INSTALLATION INSTRUCTIONS VENETIAN 84" SLIDING SHOWER DO SYSTEM (180º INSTALLATION) 28539 Industry Drive, Valencia, CA 91355 Toll Free Phone: (877) 728-3874 Toll Free Fax: (888) 440-9567 Phone: (661) 775-1675
More informationPack Mount Instructions:
Pack Mount Instructions: STEP 1 Mounting upright base to desired surface If mounting to a surface with an accessible backside (such as a thin walled container): Option 1 Discard the Round Mounting Disk
More informationThanks for shopping with Improvements! Space-Saving Wall-Mount Drying Rack - Small Item #504668
Thanks for shopping with Improvements! Space-Saving Wall-Mount Drying Rack - Small Item #504668 Note: Read these instructions carefully before assembling. Tools required: Phillips screwdriver, flat screwdriver
More informationSentinel Series Cigar Humidor End Tables
Sentinel Series Cigar Humidor End Tables Assembly Instructions Models: Sentinel 500, 1000 and 1500 Style: Contemporary SENTINEL ASSEMBLY INSTRUCTIONS Congratulations! You have purchased a superior cigar
More informationAssembly Instructions 10 X 10 Aluminum Frame Building
Assembly Instructions 10 X 10 Aluminum Frame Building 27 97 9 8 47 36 74 52 10 10 X 10 Square Building W/ Dome Includes: The Steel Entry Door with a Dead Bolt Lock assembly and Aluminum Door Frame. Metal
More informationJenny Legs Assembly Instructions
Jenny Legs Assembly Instructions R EXTENDED PHILLIPS BIT MM ALLEN WRENCH 6MM HEX DRIVE /" 007 Steelcase Inc. Grand Rapids, MI 90 U.S.A. Printed in U.S.A. Page of 6 88000 Rev F Jenny Club Instructions:
More informationThanks for shopping with Improvements! Essex Hall Tree Item #583143
Thanks for shopping with Improvements! Essex Hall Tree Item #583143 Note: Read these instructions carefully before assembling. Tools required: Philips screwdriver (not included). Find a clean, smooth area
More informationmila-wall (Series100) General Operating Instructions page 1 of 15
mila-wall (Series100) General Operating Instructions page 1 of 15 Step #1: Before setting up walls, lower adjustable leveling feet on each panel approximately 1". This will allow access to the threaded
More information#916 CLASSIC 16 GUN CABINET ASSEMBLY INSTRUCTIONS
Thank you for purchasing this quality product. A list of PARTS and INSTRUCTIONS is included to assist you. Unpack and identify all parts included on the Parts List and Hardware List. If parts are missing,
More informationEND FRAMES. End frames built using pressure treated 2x4 (1 1/2" x 3 1/2") 36" 34" 7/16" pilot hole. 5 1/2" x 1/2" lag bolt 8" wheel 23"
END FRAMES End frames built using pressure treated 2x4 (1 1/2" x 3 1/2") 23" 17 1/2" (B) (B) Measure from the bottom of your stone to 1" below the lip to get your measurement. 17 1/2"(B) 36" 34" 1/2" flat
More informationASSEMBLY AND ADJUSTMENT
EDGE MONITOR ARM EDGE Rev A 2/17 Model EDGE-SLV Model EDGE-BLK Model EDGE-WHT ASSEMBLY AND ADJUSTMENT EDGE MONITOR ARM PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the assembly and
More informationEquilibrium. Conference Table. Installation Instruction. Revision B 11/07/16
Equilibrium Conference Table Installation Instruction Revision B 11/07/16 Equilibrium End User Agreement Enwork Equilibrium table bases must be installed directly onto a four inch minimum thickness concrete
More informationE DRAWER BEDSIDE
EPSOM collection E7102 2 DRAWER BEDSIDE Congratulations on your purchase of your EPSOM 2 DRAWER BEDSIDE. The EPSOM Collection is made in New Zealand from 100% New Zealand made MDF an environmentally sound
More informationLOWLINE SINGLE FOLD DOWN WALL BEDS
ASSEMBLY INSTRUCTIONS LOWLINE SINGLE FOLD DOWN WALL BEDS Tools Required For Assembly No 2 & No 4 Phillips Head Screwdrivers No 2 Slot Head Screwdriver Hammer Electric Drill (Hammer Drill for Masonry) 6.5mm
More information2 shelf bookcase. >> assembly instructions. ebony style # BK2SHLFXEB dpci # espresso style # BK2SHLFXES dpci #
2 shelf bookcase ebony style # BK2SHLFXEB dpci # 249-4-005 espresso style # BK2SHLFXES dpci # 249-4-006 midtone/cherry style # BK2SHLFXMT dpci # 249-4-007 white style # BK2SHLFXWH dpci # 249-4-0050 chestnut
More informationPIVOT BUFFET HARDWARE TOOLS REQUIRED COMPONENTS. 8 - cams 8 - cam screws bolts 44 - flat washers shelf pins.
PIVOT BUFFET HRDWRE 8 - cams 8 - cam screws 44 - bolts 44 - flat washers 44 - spring washers 8 - screws 16 - shelf pins Thank you for purchasing the Pivot Buffet. This page lists all the contents included
More informationAssembly Instructions for 12x16 Floating Dock
Assembly Instructions for 12x16 Floating Dock www.rollingbarge.com Congratulations on the purchase of your Floating Dock kit. This kit includes all the aluminum frame parts, and all the fasteners. You
More informationT A P N T W I S T INSTALLATION GUIDE
T A P N T W I S T a dynamite way to install balusters INSTALLATION GUIDE T A P N T W I S T a dynamite way to install balusters Your Beautiful New Staircase is Just Steps Away! Tools You Need: Tape Measure
More informationIDR assembly instructions:
IDR assembly instructions: Required Tools: 2 X 12mm Open End Wrench 14mm open end wrench #2 Phillips Head Screw Driver (Drill with adjustable torque clutch recommended) 8mm nut driver (Supplied in IDR-AK)
More information1 Door Wall Unit ASSEMBLY GUIDE. Page 1 of 7 14/04/2009 Revision 3. WARNING: Contains small parts, keep out of reach of children.
ASSEMBLY GUIDE 1 Door Wall Unit IMPORTANT Before Commencing Assembly: Read all instructions COMPLETELY Ensure all listed parts are present If any parts are missing from Parts List 1, please contact 1800
More informationAssembly Instructions. Important!
Play Action Spiral Tube Slide Assembly Instructions Important! Intended for residential use by children ages 2 to 10, only on properly installed PlayStar playsets. Before use refer to complete safety guidelines
More informationSteele TV Stand Stock # BH
LOT NUMBER: DATE PURCHASED: / / Steele TV Stand Stock # BH46-084-899-02 ADULT ASSEMBLY REQUIRED If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the store
More information1 Door Base Unit ASSEMBLY GUIDE. Page 1 of 9. WARNING: Contains small parts, keep out of reach of children.
Page 1 of 9 ASSEMBLY GUIDE 1 Door Base Unit IMPORTANT Before Commencing Assembly: Read all instructions COMPLETELY Ensure all listed parts are present If any parts are missing from Parts List 1, please
More informationLaminate Cabinet Installation Instructions
Laminate Cabinet Installation Instructions www.easygaragestorage.com/installation How To Use These Instructions Thank you for your purchase! Please read each step of this manual thoroughly to ensure proper
More informationhttps://www.wallbedsbywilding.com/wallbed-installation-studio-series/
For Wallbed models: KING SIZE INSTRUCTION BOOKLET #C1 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED
More information2 Door Base Unit ASSEMBLY GUIDE. Page 1 of 9 28/04/2009 Revision 3. WARNING: Contains small parts, keep out of reach of children.
ASSEMBLY GUIDE 2 Door Base Unit IMPORTANT Before Commencing Assembly: Read all instructions COMPLETELY Ensure all listed parts are present If any parts are missing from Parts List 1, please contact 1800
More informationVINTNER WINE TOWER HARDWARE TOOLS REQUIRED COMPONENTS cam covers cams 16 - cam screws. 1 - pull small screws.
HRDWRE 16 - cams 16 - cam s 16 - cam covers 1 - pull 1 - pull bolt 40 - wood dowels 28 - small s 8 - medium s Thank you for purchasing the Vintner Wine Tower. This page lists all the contents included
More informationCOCKPIT CORNER UNIT WARNING. Illustration 1. Read all instructions and review illustrations before installing. Tools required for assembly:
Illustration 1 Illustration 2 Right side of Illustration 3 Right brace Right brace Read all instructions and review illustrations before installing. Tools required for assembly: Phillips screwdriver Rubber
More informationFor Wallbed models: KING SIZE INSTRUCTION BOOKLET #C1 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED
More informationINSTRUCTION BOOKLET #C21. For Wallbed models: KING SIZE
For Wallbed models: KING SIZE INSTRUCTION BOOKLET #C1 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT
More information11 6 Round Building Assembly Instructions
11 6 Round Building Assembly Instructions 11 6 Round Building Hardware List 1. Pro Rib Brite White 36 Wide X 68 Long (Siding Steel) 11 2. Top Wall Wheel Ring 3 3. Base Ring 3 4. 1 ½ X 68 Aluminum Tubes
More informationSUMMIT HUTCH ASSEMBLY HARDWARE WALL MOUNTING HARDWARE TOOLS REQUIRED COMPONENTS. 4 - large. 4 - bolts 4 - flat 4 - spring small screws.
SSEMBLY HRDWRE Missing hardware? Please call 800.606.6387 for replacements. 20 - small 4 - large 4 - bolts 4 - flat 4 - spring washers washers 8 - shelf pins 4 - cam 4 - cams 2 - connecting brackets WLL
More informationFree Standing Frame and Canopy
Patriot Docks Free Standing Frame and Canopy Required Tools: Cordless Drill, 3/8 drill bit, 17mm wrench, 18mm wrench, 6mm hex key (included), 8mm hex key (included) Helpful Tips: Assembling and installing
More informationFA968800TX Manchester Fireplace Console - Brown Mahogany Assembly Instructions
FA968800TX Manchester Fireplace Console - Brown Mahogany Assembly Instructions For assistance with assembly, contact: Southern Enterprises Inc. Customer Service 1-800-633-5096 service@seidal.com www.seidal.com
More informationThis instruction manual is an in-depth look and explanation of how to assemble and install the Murphy Bed properly and efficiently.
This instruction manual is an in-depth look and explanation of how to assemble and install the Murphy Bed properly and efficiently. Don t be put off by the size of the instruction manual as the large diagrams
More informationAssembly Instructions. Important!
Play Action Spiral Tube Slide Assembly Instructions Important! Intended for residential use by children ages 2 to 10, only on properly installed PlayStar playsets. Before use refer to complete safety guidelines
More informationMH60/MH72 DESK HUTCH IMPORTANT!
MH60/M2 DESK HUTCH IMPORTANT! Assembly may require the assistance of another person. Before you begin assembly: READ THE DIRECTIONS all the way through one time. This will speed up the process and help
More informationDesk/Wall-Mount Rack
Desk/Wall-Mount Rack Patent(s) Pending Installation Instructions Post P/N: 119-1752 119-1781 119-1782 119-4014 Frame P/N: 119-1591 119-1754 119-1755 Kit Contents (2) Frames (4) Posts Assembly Hardware
More informationINSTRUCTION BOOKLET #34. For Wallbed models: KING SIZE SIERRA WITH STORAGE HEADBOARD
For Wallbed models: KING SIZE SIERRA WITH STORAGE HEADBOARD INSTRUCTION BOOKLET #34 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION
More informationCopyright 2010, by Walker Edison Furniture Co., LLC. All rights reserved.
General Assembly Guidelines I. Insure that all parts and hardware are available before beginning assembly. II. III. IV. Follow each step carefully to insure the proper assembly of this product. Two people
More informationSide Mount INSTRUCTION BOOKLET #C122 BED STYLE: PARK CITY
Side Mount BED STYLE: PARK CITY INSTRUCTION BOOKLET #C1 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS PARTS REQUIRED Single QuickStand Lite Parts A (1) Lower Arm A B C D B (1) Upper Arm C (1) Base D (1) Base Plate E (1) M8 Dynamic Arm Long F (1) Clamp Bracket G H (1) VESA Plate
More informationTools Required. Bench Hardware. Bench Parts. Planter Hardware. Planter Parts. BENCH/PLANTER INSTALLATION GUIDELINES for
Arbor Collection / Harvest Collection / Terra Collection Page 1 Please read all instructions completely before starting any part of the installation. Each AZEK and Kit comes complete with all hardware,
More informationMANUAL e130. Wallstation
MANUAL 07.29.13 e130 Wallstation The Enovate Medical e130 Wallstation was designed to set a new standard in quality. Enovate Medical s goal is to provide a wallstation that is ready for years of use,
More informationParts List (Continued) 18 each: #8 x 0.625" Truss Head Phillips Screw 20 each: #8 x 1.75" Flat Head Phillips Screw 4 each: #8 x 1.25" Flat Head Philli
EVO Tall Pull-Out Wood Pantry Important Notes Always read the instructions completely and carefully before beginning assembly. Remove and check contents for damage and/or missing parts. Keep the original
More informationConstable Oak Extension Dining Table
Constable Oak Extension Dining Table Assembly Instructions - Please keep for future reference 176/0325 Dimensions Width - 160/ 200cm Depth - 90cm Height - 75cm Important - Please read these instructions
More informationFOLDAWAY DOOR SECTION OPTION 6. Assembly Instructions. Folding Work Desk (adjustable shelves behind can be accessed when the desk is in use)
FOLDAWAY DOOR SECTION OPTION 6 Folding Work Desk (adjustable shelves behind can be accessed when the desk is in use) Assembly Instructions It is strongly recommended to have two persons present when assembling
More informationTrack Rack. * Track Racks are not lockable
The Track Rack s unique staggered, sliding hook design creates the greatest parking efficiency while still providing easy access to any particular bike. When adding or removing a bike to the rack, simply
More informationUnion Arch Safety Gate
33000 Please read the following instructions carefully. Keep this instruction manual for future reference. Tools required: Phillips head screwdriver, drill (for top of stair installation), and pencil (not
More informationQueen Wingback Bed King Wingback Bed
Parts and Hardware List A. Side Rails with Attachment Hooks 2 pcs B. Foot Rail 1 pc C. Head Rail 1 pc D. Center Support Slat 1 pc E. Leg Supports 3 pcs F. Support Slats 4 pcs G. Flat Washers 8 pcs H. Lock
More informationFACE PANELS & INSTALLATION INSTRUCTIONS MANUAL, MECHANICAL ASSIST & ECLIPSE POWERED SYSTEMS TM SECTION I SECTION II SECTION III SECTION IV SECTION V
FACE PANELS & BACK PANELS by Spacesaver INSTALLATION INSTRUCTIONS MANUAL, MECHANICAL ASSIST & ECLIPSE POWERED SYSTEMS TM SECTION I INTRODUCTION SECTION II LIBRARY SHELVING PANELS SECTION III 4-POST SHELVING
More informationBISON GOOSENECK FOOTBALL 1 PAIR OF GOAL POSTS
Instruction Manual BISON GOOSENECK FOOTBALL 1 PAIR OF GOAL POSTS Customer Service (800) 247-7668 P A R T S L I S T Item Qty Description Item Qty Description A 2 GOOSENECK POLE I 4 UPRIGHTS B 2 BAND CLAMP
More informationMain Street Safety Gate
27930 Please read the following instructions carefully. Keep this instruction manual for future reference. Tools required: Phillips head screwdriver, drill (for top of stair installation), and pencil (not
More informationINSTRUCTION BOOKLET #C10 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY.
More information2 Door Tall/Split Unit
ASSEMBLY GUIDE 2 Door Tall/Split Unit IMPORTANT Before Commencing Assembly: Read all instructions COMPLETELY Ensure all listed parts are present If any parts are missing from Parts List 1, please contact
More informationMobileTrak5 Installation Instructions
MobileTrak5 Installation Instructions PLEASE OPEN ALL BOXES & CHECK TO MAKE SURE YOU HAVE ALL PIECES REQUIRED READ ALL INSTRUCTIONS BEFORE STARTING Tools Required for Assembly 7/16, 1/2 Wrench Phillips
More informationAWNING / PATIO COVER INSTALLATION INSTRUCTIONS
AWNING / PATIO COVER INSTALLATION INSTRUCTIONS Before You Begin Read the installation instructions thoroughly before beginning the installation procedure. Perspective In the Awning Instructions, Back means
More informationReal Life Ninja Complete Starter Pack (14ft. Warped Wall) Assembly Instructions
MATERIALS: 3 - Main Sections (Only 2 Sections for 10 ) 8 3 deck screws for joining sections inside of 2 Rock Wall Panels (with pre-installed t-nuts. Top panel comes with ladder mounting block preinstalled.)
More informationBIKE FILE (301)
B IK E F I L E High Efficiency The Bike File is our most space efficient u-lock compatible product. Sturdy sliding hangers allow nine bikes to be securely stored in an eight-foot section while allowing
More informationINSTALLATION INSTRUCTIONS RH 412 STEEL DOORS
By following the steps outlined below, the assembly, installation and adjustment of the steel doors, will be a simple process. Let s start with the Driver Side. Note: Having the hood open makes the job
More informationCommercial Wine & Liquor Display. Double Displays
Commercial Wine & Liquor Display Double Displays Congratulations! You have purchased a superior commercial wine rack kit. These commercial kits have been specifically designed to properly store and display
More informationMaking Simple Bookbinding Equipment
Tony Firman 20 1 2 19 Notes Tony Firman Tony Firman Bookbinding 18 3 : 2012 Tony Firman Bookbinding P.O. Box 507 Haslet, TX 76052 www.tonyfirmanbookbinding.com 4. When all the tapes have been pinned in
More informationTOOLS REQUIRED
VINTNER UFFET HRDWRE 16 - wood dowels 26 - back 16 - bolts 4 - pull bolts Thank you for purchasing the Vintner uffet. This page lists all the contents included in the box. Please take time to identify
More informationINSTRUCTION BOOKLET #C0 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY.
More informationHawko LED Flex & Accessories Installation Instructions
LED Flex & Profiles Hawko LED Flex & Accessories Installation Instructions Contents Installation of IP20 LED Flex 4 Installation of IP67 LED Flex 6 Mounting Channel Installation 8 Mounting Clip Installation
More information