Kirra Buffet Assembly Instructions

Transcription

1 Thank you for your purchase. lease follow the instructions below for correct assembly. C B dowel screw x x6 wedge x4 screw x4 bolt x locking nut x long screw x F screw slide x6 rail x N wheel x4 G slide rail x H slide slide rail x rail x O Q wheel x4 shelf plugs x small bolt x Hardware Supplied I screw x4 R V W X Y Z safety strap x screw x wall anchor x wall screw x washer x Wall Strap small locking nut x WRNING: ny furniture that is not anchored to a wall has the potential to tip over in certain circumstances, i.e. if a child attempts to climb up on the furniture or in the event of an earthquake. ccordingly, we recommend that all furniture is anchored to a wall. We supply a free safety wall anchor with all furniture sold and we recommend these are used to prevent your product tipping. The fixing device provided should fit most wall types, but please note that different wall materials may require different fixing devices from those supplied. hillips & Flathead screwdrivers required. For quicker assembly, we recommend the use of a power drill on a low-speed setting.

2 C CR G C G G G C C C C C C C F F F F ttach x slide rails (G) to panel [] and secure with 6x small screws (). ttach x slide rails (F) to panel [] and secure with 6x small screws (). Tighten with a screwdriver. Insert x dowels () to panel []. Insert x bolts (C) into panel []. Tighten with a screwdriver.

3 4 4 0 ttach panels [], [], [4] and [] to panel [] and secure with x locking nuts (). Tighten with a screwdriver. Insert connector [] to join panels [].Insert connector [0] to join panels [].

4 Slide panels [] and [] between the grooves of panels [], [], [4] and [] to form the back of the unit, as shown. Insert x dowels () into the ends of panels [], [], [4] and []. ttach panel [7] to the unit and secure with x screws (). Tighten with a screwdriver. 4

5 ttach the legs [4] and [] to panel [7] as shown using 4x screw (). Tighten with a screwdriver. 6 6 Insert x shelf plugs () into the end cavities of the cabinet as shown.insert the shelf panels [6] and balance on top of the plugs.

6 0 O O N N back O O N N ttach x wheels (O) and (N) to each panel [] and [] as shown, and secure with x screws (). Tighten with a screwdriver. Note: If the door is not sliding smoothly or sitting straight, there is a screw in the middle of the wheel on the bottom of each door that can be tightened/loosened until the door is sitting properly. O ttach door panels [] and [] as shown, starting with the back door first and then the front door. ress the clip down on the back of the door to assemble the door. ush the clip back up to lock into place. 6

7 Q Q R 7 R Q Q 6 x R 6 R x Insert 4x small bolts (Q) to panel [6]. Tighten with a screwdriver. ttach panels [7] and [] to panel [6] and secure with 4x small locking nuts (R). Tighten with a screwdriver. 7

8 4 B B B B 6 x Slide panel [] down along the grooves of panels [7] and []. x ttach panel [7], [] and [0] as shown using 4x screws (B). Tighten with a screwdriver.

9 6 I 6 6 H x ttach slide rails (I) and slide rails (H) to the underside of the side panels as shown. Secure with 4x screws () and tighten with a screwdriver. Insert the assembled drawers into the corresponding compartments as shown. nsure the drawers slide easily along the rails.

10 7 V Z W X Z Y V Z W ttach 4x wedges () into the corners of the back of the unit and secure with 4x screws (). Tighten with a screwdriver.ttach x safety strap (V) to the top of the back side of the unit as shown using x washer (Z) and x screw (W). Tighten with a screwdriver. Once assembled lift furniture into place, do not drag. Use a drill to create a small hole lining up with the top of the safety strap (V). Fasten to wall using x washer (Z), x wall plug (X) and x screw (Y). nsure unit is balanced and steady before use. You re done, enjoy! 0