PERSONAL RECORD KEEPING

Size: px

Start display at page:

Download "PERSONAL RECORD KEEPING"

Douglas Stokes
5 years ago
Views:

1 Q47e/Q47ce

2 2

3 Q 4 7 e / Q 4 7 c e A s s e m b l y i n s t r u c t i o n s PERSONAL RECORD KEEPING IMPORTANT: Record the serial numbers of your Octane Fitness elliptical in the spaces below. This will make it easier for you to obtain accurate and timely response should any service issues occur with your elliptical machine. Also, don t forget to register your warranty on the web at ATTENTION All serial numbers begin with a letter. Base Serial Number located below front right chrome rail at the power inlet Console Serial Number located on the lower edge of the console If you have any additional questions or need additional assistance in assembly, please contact your local service provider or Octane Fitness Customer Service at OCTANE4 ext. 1. You may also visit us on the web at WARNING: Machine contains moving parts. Use caution when assembling and operating this machine. This product is intended for household use. 3

4 Q 4 7 e / Q 4 7 c e C o n t e n t s The Octane Fitness base box contains the following: Tools required: A) 1 - Octane Fitness cross trainer base Phillips screwdriver B) 1 - Console mast 17mm wrench or adjustable wrench C) 1 - Top cover 17mm socket and ratchet D) 1 - Access panel 6mm hex key wrench E) 1 - Detached right pedal lever F) 1 - Left moving handlebar G) 1 - Right moving handlebar H) 2 - Handlebar covers I) 1 - Mast boot J) 1 - Hardware pack (see opposite page) B o x C o n t e n t s A B C D E F G H I 4

5 Hardware Pack (J) includes: K) 8-6mm hex key chamfered bolt (for moving handlebar) L) 2 - Phillips screws (for mounting access panel) M) 2 - Phillips screws with washers (for mounting top cover) N) 1 - Cable tie (for securing loose wires to mast) N K L M M o v i n g t h e P r o d u c t It is safest to move the product to its installation location in its shipping carton. It may be easier to move the product into your home after you remove it from the packaging, but be careful not to hit any walls or doors. The Q47e/Q47ce features transport wheels on the front of the unit. Be careful when moving from one surface to another, such as hardwood floor to carpet. Note: If you need to pick up your elliptical there are hand placement slots under the front shroud. Please take caution when lifting. The elliptical weighs 280 lbs. when fully assembled. Tip: When using the front transport wheels, it is easier to pull the unit rather than push it. 5

6 The Q47/Q47ce console box contains the following: 1) 1 - Deluxe console 2) 1 - Deluxe keypad 3) 2 - Console back arcs (left and right) 4) 1 - Power supply 5) 1 - Octane Fitness wireless heart rate transmitter and elastic strap 6) 1 - Information packet 7) 4 - Phillips 18mm screws (not pictured) 8) 4 - Phillips 12mm screws (not pictured) CALORIES STRIDE Beginner 10K PowerWalk Stride Interval Dual Direction Stride Burst 5 2 Quick Start My Quick Start 1 My Quick Start 2 ArmBlaster Fan Now-Zone Cool Down Glute Kicker Pause Clear 6 Enter Time Weight 1 Program Stride Level Age Q47/Q47e/Q47ce The Q47ce console box also contains the Contact Heart Rate (ce) kit (not pictured), which includes: a) 1- Cable assembly for heart rate grips b) 2 - Left side grips c) 2 - Right side grips d) 2 - Rubber gaskets e) 4-2mm hex head screws f) 1-2mm hex key wrench g) 2 - Primary (top) contact plates h) 2 - Secondary (bottom) contact plates 6

7 1. Attach pedal lever a. Remove bolt from 3-pivot link. b. Place right pedal lever (E) through leg slot in rear shroud and attach it to the 3-pivot link. Check to see that the rollers are seated and properly aligned on the rails before securing the pedal lever. c. Tighten the bolt and nut securely using 17mm socket and wrench. 2. Attach moving handlebars Moving handlebars are labeled left and right, be sure to install accordingly. a. Align the bottom of the handlebar with the four holes in the pivot shaft and attach with four 6mm hex key bolts (K) make sure these bolts are very tight; torque to 30 ft-lbs. b. Reaching inside from the front of the machine, carefully connect the cable coming from the base of the handlebar (F or G) to the cable by the pivot shaft. Gently tug both cables to ensure the connectors are completely seated. c. Position the handlebar cover (H) over the handlebar pivot point and press firmly at top and bottom to attach. d. Repeat for the other side. Pivot shaft Cable on frame Cable from handlebar 7

8 3. install access panel a. Loosen the screws on the left and right sides of the lower shroud near the front of the unit. (These screws secure the side of the shroud and the access panel to the frame.) b. Slide the metal plate of the access panel (D) behind the back shroud. Fit the tabs on each side of the access panel into the slots between the side of the main shroud and the frame, over the top of the screws. c. Tighten the screws on each side, then secure the back of the access panel with 2 Phillips screws (L). Tabs Slot for Tab Back Screws Screw to loosen on both sides 4. install console mast a. Attach the console mast (B) by placing the keyhole slots in the mast plate over the bolts and sliding the console mast toward the pedals. b. Tighten the four 6mm hex key bolts attaching console mast to frame. c. Connect the black cable connector coming from the mast to the black cable connector on the base frame. Tug the cables gently to ensure the connectors are completely seated. d. Use the cable tie (N) to secure any loose cable to the bottom of the mast; cut off any excess cable tie. 8

9 5. mount the keypad to the console mast If you have the Q47e keypad: a. Remove the two screws securing the console back piece to the mast plate. b. Route the cable from the heart rate board down through the top of the mast tube and out of the hole beneath the console plate. c. Route the red and white fan wires with the white connector down through the top of the mast tube and out of the hole beneath the console plate. d. Attach the black ribbon cable connector from the top of the console mast tube to its connection on the back of the keypad (2). Tug the cables gently to ensure the connectors are completely seated. e. Position the keypad (2) on the mast (B) and insert each of the 4 shorter screws through the mast holes and into the keypad back. Tighten screws to secure. If you have the Q47ce keypad: a. Remove the two screws securing the console back piece to the mast plate. b. Use a utility knife to cut the rubber grips and remove them from the stationary handlebars. c. Leading with the white plastic connector, insert the contact heart rate cable (a) through the hole in the user s right side of the mast and feed it up through the mast tube. d. Feed the cable for the right grip, labeled Right Hand Contact, up through the right handlebar tube. e. Feed the cable for the left grip through the hole in the user s right side of the mast and through the hole on the user s left side, then feed it up through the left handlebar tube. f. Select a left side grip (b), differentiated from a right side grip (c) by two screw holes. Place a rubber gasket (d) into the left half of the contact grip, and position on the left handlebar. g. Position the small white wire out in the slot at the top of the left half of the hand grip (the side closest to a user standing on the pedals). Position the small red wire in the slot at the bottom of the hand grip (away from the user). h. Select a right side grip (c), fit it with the left half around the handlebar, and secure the two halves together using two 2mm screws (e). Make sure that the wires are in the slots, not clamped between the grips; tighten the screws until that the grip is stable. 9

10 i. Select a primary contact plate (g) that matches the contour of the top of the plastic grip (closest to a user). Peel the blue protective film off of the tab on the primary contact plate (g), then slide the tab into the connector at the end of the small white wire. j. Select a secondary contact plate (h) that matches the contour of the bottom of the plastic grip (away from the user). Peel the blue protecting film off of the tab on the secondary contact plate (h) and slide the tab into the connector at the end of the remaining wire. k. Repeat steps (f) through (k) for the right handlebar. l. Push any extra lengths of wire into the mast tube. m. Insert the connector at the end of the heart rate cable into its connector on the heart rate board on the back of the keypad. (This is a two-wire cable ending in a single connector.) Route the contact heart rate cable wires around the posts on the back of the keypad, in the same manner that the other heart rate cable is routed (see figure at right). n. Route the cable from the other end of the heart rate board down through the top of the mast tube and out of the hole beneath the console plate. o. Route the red and white fan wires with the white connector down through the top of the mast tube and out of the hole beneath the console plate. p. Attach the black ribbon cable connector from the keypad (2) to its cable coming from the top of the mast. Tug the cables gently to ensure the connectors are completely seated. q. Position the keypad (2) on the mast (B) and insert each of the 4 shorter screws with washers through the mast holes and into the keypad back. Tighten screws to secure. r. Remove the film from the adhesives on the primary contact plates (g) and secondary contact plates (h) and carefully press the plates onto the grips, pushing the tabs, connectors, and wires inside the grips. It is recommended that you wait to adhere the grips until after you have installed the console and verified that the contact heart rate grips are transmitting a reading to the console. Route Contact Heart Rate Cables Here Standard Heart Rate Connection Q47e/Q47ce only Contact Heart Rate Board Contact Heart Rate Connection Q47ce only Connector for Grip Wire Console/Keypad Connection (all models) Fan Wire Q47e/Q47ce only Note: If you are using the optional LCD Mounting Arm, skip step 6 of these instructions and instead follow the instructions included with the LCD Mounting Arm. Once you have completed those instructions, resume assembly of your Q47e/Q47ce with step 7 of these instructions. Keypad Ground Connection (all models) 10

11 6. mount the console to the console mast Note: Record the serial number of your console, located on the lower edge of the console, before attaching the console to the console mast. (If you have installed the optional LCD Mounting Arm, and mounted the console to the mast according to those instructions, skip to Step 7.) If you have the Q47e/Q47ce console: a. Position the console (1) on the plate at the top of the mast (B) and place the left back arc (3) behind it. Holding both in place, insert 2 of the longer (18mm) Phillips screws partially through the back arc (3) and the mast plate into the console back. Repeat on the right side. Tighten all screws to secure. b. Attach the white 12-pin main connector to its connection on the back of the console. Tug the cable gently to ensure the connector is completely seated. c. Attach the black keypad connector to its connection on the back of the console. Tug the cable gently to ensure the connector is completely seated. d. Attach the metal connector on the green ground wire that is connected to the back of the mast plate to its connection on the back of the console. Tug the ground wire gently to ensure the connector is completely seated. e. Attach the white 3-pin heart rate connector to its connection on the back of the console. Tug the cable gently to ensure the connector is completely seated. f. Attach the white 2-pin fan connector to its connection on the back of the console. Tug the wires gently to ensure the connector is completely seated. g. Plug in the unit and verify that the console LEDs light and that the Level and Stride control buttons on the moving handlebars are working. If you have the Q47ce console, grasp the contact heart rate handgrips and verify that a heart rate reading appears on the console. If any issues are detected, recheck the connections, or contact Octane Fitness Customer Service for assistance. Once you have verified these functions, unplug and proceed with remaining steps. h. Make sure excess cable is pushed into the mast tube. i. Reposition the console back piece and reattach it using the two screws provided. Console to Base (white, 12-pin) Console Ground All models (metal; green wire) All models Heart Rate (white, 3-pin) Q47e/Q47ce only Keypad (black) All models Fan (white, 2-pin) Q47e/Q47ce only 11

12 7. Adjust arms (optional) Note: Before completing this step, plug in and ride your elliptical cross trainer for a few moments to get a feel for the arm motion. If the reach of the arm motion feels right (as it will for most users), proceed to step 8. If the reach is too long or too short, carefully follow these steps to shorten or extend the reach by approximately 1.5 inches: a. Locate the rod end link that connects to the black bar (pivot) inside the machine. The black bar has three holes in it with the rod end link attached through the center hole with a 6mm hex key bolt and a 13mm nut. A spacer separates the black bar and the rod end link. b. While supporting the arm, remove the 13mm nut from the 6mm hex key bolt and carefully ease the bolt from the center hole in the black bar. To extend the reach of the arm, re-insert the bolt in the hole closest to the front of your elliptical trainer. To shorten the reach, re-insert the bolt in the hole closest to the user end of the machine. Make sure that the spacer remains in place between the rod end link and the black bar, with the pocket side of the spacer toward the rod end link. c. Replace the nut and tighten. This connection must be very tight. d. Repeat for the other arm. Should you have any questions or concerns in making this adjustment, please contact your local service provider or contact Octane Fitness Customer Service at OCTANE4, ext Place top cover a Align top cover (C) on top of main housing. Hold the back edge (near the mast) in place and shift the front edge forward until it settles into position. b. While still holding the back edge in place, press firmly on the bottom edge of the front of the cover until it snaps into place. You will feel and hear it snap into place as the plastic bracket on the inside of the front bottom edge clips onto the steel tube at the front of the main frame. c. Secure the top cover to the frame using 2 Phillips screws with washers (M). Press here Steel tube Hold here Secure with screws 12

13 9. install mast boot a. Place the rubber mast boot (I) around the mast (B), covering the open ends of the stationary handlebars. b. Tuck the ends of the mast boot (I) into the channels in the access panel (D) just below the stationary handlebars. 10. Adjust levelers a. Adjust all four levelers to make sure the product sits flat on the floor. For a lower step up height, screw the rear levelers into the rear stabilizer bracket. Then level the machine using the front levelers. b. Tighten the leveler nut against the frame for each leveler. Note: CAUTION: If you move your Q47e/Q47ce, you may need to adjust the levelers to make sure your product is level with the floor. If the unit is not level, it may not function properly. 11. Plug in product a. First, insert the plug into the product, located just below the right roller track. Next, route the cable toward the wall outlet. You can run it under the product to avoid seeing it or tripping on the cable. Ensure that the cord will not be pinched and become damaged. Plug the product into the wall. Note: There is no need to turn off your product your Q47e/Q47ce was designed with an intelligent sleep mode a virtual off button. This eliminates the need for an on/off switch. When your product is in sleep mode, it uses very little power. Unplugging your elliptical will not harm or erase My QuickStart profiles. 13

14 N O T E S 14

15 N O T E S 15

16 Are you passionate about your workout and the results? Share your story with others on the Octane Fitness web site. Go to: Then click on Share My Story and show the world how fueled you are. F U E L Y O U R L I F E 9200 Wyoming Avenue North, Suite 380 Brooklyn Park, MN OCTANE Octane Fitness, LLC. All rights reserved. Octane Fitness, DedicatedLogic, Fuel Your Life, HeartLogic, Now-Zone and X-Mode are registered trademarks of Octane Fitness. Any use of these trademarks, without the express written consent of Octane Fitness, is forbidden REV A

PERSONAL RECORD KEEPING

2 P R O 3 7 0 A s s e m b l y i n s t r u c t i o n s PERSONAL RECORD KEEPING Tip: Record the serial numbers of your Octane Fitness elliptical in the spaces below. This will make it easier for you to obtain