May 2016 Greetings to Go. Creative License

Transcription

1 Assembly Line Cardmaking May 2016 Greetings to Go Creative License Creative License Materials: Greetings to Go Tools and Supplies: Scor-Pal Adhesive Tape Foam Adhesive Paper Trimmer 3x14 CS Grid Ruler Scissors CS Glue Pen CS Ash Ink Tonic Paper Distressing Tool (Optional) Craft Knife and Cutting Mat Preparation: 1. Trim the Off White and Lt. Gray printed cutaparts into sections as indicated by the artwork and cutting guidelines. Some of the cutaparts have been trimmed in more detail with a scissors or craft knife. Those cuts are optional. 2. Scoring and folding information is listed within the instructions for each card set. TIP: The bump of the score goes on the inside of the fold. 3. If you do not have an item to complete the card as shown, simply omit or substitute the item. All rights reserved.

2 May 2016 Creative License Greetings to Go Page 2 of 5 Set A: 4¼x5½ Aqua Cards with 2¾x5¼ Gun Metal Panels Score and fold each 5½x10¼ Aqua Cards horizontally at 3 and 6. Notes: Nest the Lt. Gray cutapart onto the Gun Metal panel and adhere to the front flap of the card; trim the license plate from the Off White cutapart, tape a loop of black ribbon to the back, and attach past the right edge of the flap; adhere a silver key charm beneath the plate; add the Lt. Gray cutapart strip to the right edge of the card base; inside: Hope your day is wonderful. Notes: Attach a loop of black ribbon behind the White cutapart and adhere to the right edge of the Gun Metal panel; glue a silver key charm to the cutapart; place the Lt. Gray cutapart onto the right edge of the card base; inside: Happy belated birthday. Notes: Trim along the curve on the right edge of the Off White cutapart; nest the cutapart onto the Gun Metal panel; cut vshaped points into a strip of black ribbon; adhere to the cutapart and glue a key to the ribbon; inside: Happy Birthday and Enjoy. Notes: Trim the 2.75x5.25 Gun Metal panel vertically at 2-5/8 and 1-3/8. Nest the Off White cutaparts onto the panels and adhere to the front flap of the card; attach the Just wanted to say... cutapart to the right edge of the flap; adhere the Off White cutapart strip to the right edge of the card; inside: You're on my mind.

3 May 2016 Creative License Greetings to Go Page 3 of 5 Set B: 3½x5 Off White Cards with 3¼x4¾ Rust Panels Score and fold each 3½x10 Off White Card horizontally at 5. Notes: Trim the Off White cutaparts to the outlined oval shape and distress edges to disguise cutting imperfections; layer onto the Rust panel and use a craft knife to cut along the oval shape; wrap black ribbon around the upper portion of the Rust panel; trim ribbon at an angle and remove about 1/4 to create a gap; staple the gap together; adhere the Rust panel to the card base; inside birthday card: Hope your day is wonderful. and Enjoy; inside thanks card: blank. (See page five for alternative assembly instructions for the curved cards.) Notes: Shape the bottom edge of the Off White cutapart by cutting along the guideline with a craft knife and nest onto the Rust panel; inside: Enjoy the ride! Notes: Adhere the cutaparts to the Pink panel; remove the prongs from the flowershaped brads and adhere to the lower right corner of the panel with a Glue Pen; nest onto a White panel and Orange card base; inside: And smiling. Notes: Shape the bottom edge of the Off White cutapart by cutting along the guideline with a craft knife and nest onto the Rust panel; adhere the thinking of you cutapart to the upper left; inside: and wishing you an amazing day.

4 May 2016 Creative License Greetings to Go Page 4 of 5 Set C: 5x7 Yellow Cards with 4¾x6¾ and 2¼x5 Dk. Gray Panels and 4½x6½ and 2x5 Lt. Gray Panels Score and fold each 7x10 Yellow Card horizontally at 5. Notes: Nest the Off White triangle onto the Lt. Gray triangle with the angled edges aligned; open the Yellow card and adhere the nested triangle to the upper right corner; fold the Yellow corner back along the angled edge of the triangle; nest the Off White cutapart onto the left edge of the Dk. Gray panel; trim the width of the panel to fit; wrap with rust ribbon; adhere a silver key charm; attach to the left edge of the Yellow card; tack down the folded triangle; nest the large Dk. and Lt. Gray panels and add to the inside of the card; finish with the corresponding Off White triangle; inside: You're amazing. Notes: Repeat the same assembly process as with the previous card; cut the Off White hubcap cutapart into a circle and distress edges to hide trimming imperfections; adhere to the front of the card; inside: Your thoughtfulness is appreciated. Notes: Follow the same process to adhere the triangles to the top corner of the Yellow card; attach a trimmed/distressed Off White hub cap cutapart to the card front; nest the Off White Thank you strip onto the nested Lt. Gray and Dk. Gray strips; wrap the strip with rust ribbon and adhere to the bottom of the Yellow card; nest the large Lt. and Dk. Gray panels to the inside of the card; inside: I treasure our friendship and U R AMZNG. Notes: Repeat steps to adhere triangles to the upper right corner of the Yellow card base; trim the license plate shape from the Off White cutapart and adhere to the front of the card; nest the Off White Congratulations strip onto the nested Dk. and Lt. Gray panels; wrap with Rust ribbon, attach a silver key, and adhere to the card; nest the large Lt. and Dk. Gray panels onto the inside of the card and add the final triangular cutapart to the upper right corner; inside: All the best to you.

5 May 2016 Creative License Greetings to Go Page 5 of 5 Alternative assembly instructions for Set B, Cards 1 and 2: Step One: Trim oval to the outside circle and use as a template to trace the curve onto the Rust card panel; cut along the marked guideline to remove the corner from the Rust panel. Step Two: Trim the oval to the middle circle and nest into the prepared corner; layer the Rust panel onto the Off White card base.