High-Intensity LED in Plastic T-1¾ Package

Transcription

1 High-Intensity LED in Plastic T-1¾ Package OPT EK T e c h n o l o g y x x x x Narrow beam angle High brightness LED Water clear plastic package UV resistant epoxy Product Photo Here Each device in the is a high intensity LED mounted in a clear plastic T-1¾ package. Each device incorporates an integral molded lens that enables a narrow beam angle and provides an even emission pattern. Designed to produce light over a wide range of drive currents, these LEDs are useful in applications that require a higher on-axis brightness than that achievable with standard lamps. Applications x Indoor/outdoor applications x Variable message boards x Store front signage x Indicators Part Number OVLGB0C6B9 OVLGC0C6B9 OVLGS0C8B9 OVLGY0C9B9 AlInGap Package Red, Yellow Material InGaN AlInGaP Emitted Color Intensity Typ. mcd Lens Color Blue Blue-Green Red Yellow Water Clear InGaN Package Blue, Blue-Green ANODE 2 CATHODE DIMENSIONS ARE IN INCHES AND [MILLIMETERS] Beam Pattern RoHS Moisture DO NOT LOOK DIRECTLY AT LED WITH UNSHIELDED EYES OR DAMAGE TO RETINA MAY OCCUR. OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Page 1 of 10

2 Absolute Maximum Ratings T A = 25 o C Note: 1. Duty Ratio = 1/10, Pulse Width = 0.1ms 2. 4mm (.157 ) away from epoxy Parameter Red, Yellow Blue, Blue-Green DC Forward Current 30mA 20mA Peak Pulsed Forward Current 1 100mA 50mA Power Dissipation 72mW 80mW Current Linearity vs Ambient Temperature -0.5mA/ C -0.2mA/ C Junction Temperature Reverse Voltage Storage Temperature Range Operating Temperature Range Soldering Temperature C 5V -40 ~ +100 C -40 ~ +85 C 260 /5 seconds Electrical and Optical Characteristics Blue T A = 25 o C SYMBOL PARAMETER MIN TYP MAX UNITS CONDITIONS I v Luminous Intensity mcd I F = 20 ma V F Forward Voltage V I F = 20 ma I R Reverse Current µa V R = 5 V D Dominant Wavelength nm I F = 20 ma Spectral Half Width nm I F = 20 ma 2 ½H-H 50% Power Angle deg I F = 20 ma Electrical and Optical Characteristics Blue-Green T A = 25 o C SYMBOL PARAMETER MIN TYP MAX UNITS CONDITIONS I v Luminous Intensity mcd I F = 20 ma V F Forward Voltage V I F = 20 ma I R Reverse Current µa V R = 5 V D Dominant Wavelength nm I F = 20 ma Spectral Half Width nm I F = 20 ma 2 ½H-H 50% Power Angle deg I F = 20 ma Page 2 of 10

3 Electrical and Optical Characteristics Red T A = 25 o C SYMBOL PARAMETER MIN TYP MAX UNITS CONDITIONS I v Luminous Intensity mcd I F = 20 ma V F Forward Voltage V I F = 20 ma I R Reverse Current µa V R = 5 V D Dominant Wavelength nm I F = 20 ma Spectral Half Width nm I F = 20 ma 2 ½H-H 50% Power Angle deg I F = 20 ma Electrical and Optical Characteristics Yellow T A = 25 o C SYMBOL PARAMETER MIN TYP MAX UNITS CONDITIONS I v Luminous Intensity mcd I F = 20 ma V F Forward Voltage V I F = 20 ma I R Reverse Current µa V R = 5 V D Dominant Wavelength nm I F = 20 ma Spectral Half Width nm I F = 20 ma 2 ½H-H 50% Power Angle deg I F = 20 ma Standard Bins Lamps are sorted to luminous intensity (I v ) and dominant wavelength ( D ) bins shown. Orders may be filled with any or all bins contained as below. Luminous Intensity (mcd) OVLGB0C6B9 (BLUE) (I F = 20 ma) B4 BJ BM Dominant Wavelength (nm) 475 W V U Forward Voltage (V F ) Rank H J K L Voltage (V) Important Notes: 1. All ranks will be included per delivery, rank ratio will be based on the chip distribution. 2. To designate luminous intensity ranks, please contact OPTEK. OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Page 3 of 10

4 Standard Bins Lamps are sorted to luminous intensity (I v ) and dominant wavelength ( D ) bins shown. Orders may be filled with any or all bins contained as below. OVLGC0C6B9 (BLUE-GREEN ) (I F = 20 ma) Luminous Intensity (mcd) HA HB HC Dominant Wavelength (nm) 0Z 0Y 0X 511 Forward Voltage (V F ) Rank H J K L Voltage (V) Luminous Intensity (mcd) OVLGR0C6B9 (RED) (I F = 20 ma) RB R7 0Y X Dominant Wavelength (nm) Forward Voltage (V F ) Rank G H J Voltage (V) OVLGY0C6B9 (YELLOW) (I F = 20 ma) Luminous Intensity (mcd) Y3 Y4 Y Dominant Wavelength (nm) Forward Voltage (V F ) Rank G H J Voltage (V) Z 0Y 0X 595 Important Notes: 1. All ranks will be included per delivery, rank ratio will be based on the chip distribution. 2. To designate luminous intensity ranks, please contact OPTEK. Page 4 of 10

5 Typical Electro-Optical Characteristics Curves Blue (%) Forward Current vs. Forward Voltage Luminous Intensity vs. Forward Current Reverse Current vs. Reverse Voltage I R(µA) Forward Current vs. Ambient Temperature I F=20mA Luminous Intensity vs. Ambient Temperature vs. Wavelength OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Page 5 of 10

6 Typical Electro-Optical Characteristics Curves Blue-Green Forward Current vs. Forward Voltage Luminous Intensity vs. Forward Current Reverse Current vs. Reverse Voltage I R(µA) Forward Current vs. Ambient Temperature (%) Luminous Intensity vs. Ambient Temperature vs. Wavelength I F=20mA Page 6 of 10

7 Typical Electro-Optical Characteristics Curves Red Forward Current vs. Forward Voltage Luminous Intensity vs. Forward Current Reverse Current vs. Reverse Voltage I R(µA) Forward Current vs. Ambient Temperature I F=20mA Luminous Intensity vs. Ambient Temperature (%) vs. Wavelength OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Page 7 of 10

8 Typical Electro-Optical Characteristics Curves Yellow Forward Current vs. Forward Voltage Luminous Intensity vs. Forward Current Reverse Current vs. Reverse Voltage I R(µA) Forward Current vs. Ambient Temperature I F=20mA Luminous Intensity vs. Ambient Temperature (%) vs. Wavelength Page 8 of 10

9 Packing Information: Available in bulk or reel Bulk: 500 pcs/bag 13-inch reel: 2000 pcs/reel Carrier Tape Dimensions: Loaded quantity 2000 pieces per reel Moisture Resistant Packaging Label Aluminum Moisture-proof Bag Desiccant Bar Code Label OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Page 9 of 10

10 Reliability Test LED lamps are checked by reliability tests based on MIL standards. 1. Test Conditions, Acceptable Criteria & Results Page 10 of 10