Indoor and outdoor displays Backlighting Camera flash RGB full-color displays

Transcription

1 x Full-color red/green/blue x PLCC package with 6 pins x Wide viewing angle x High performance x Tuneable color mix Product Photo Here The package design provides wide viewing angle, low power consumption, and high luminous intensity. Color on demand is made possible by isolated chip circuits, allowing each LED to be driven individually or in tunable color combinations. Applications x Amusement equipment x Information boards x Automotive interior lighting x Portable appliances x x x x Indoor and outdoor displays Backlighting Camera flash RGB full-color displays Part Number Chip Type Material Emitted Color R AlInGaP Red G InGaN Green B InGaN Blue Intensity Typ. mcd Lens Color Water Clear RoHS Moisture DIMENSIONS ARE IN: [MILLIMETERS] INCHES DO NOT LOOK DIRECTLY AT LED WITH UNSHIELDED EYES OR DAMAGE TO RETINA MAY OCCUR. Phone: (972) or (800) FAX: (972) visibleled@optekinc.com Page 1 of 8

2 Absolute Maximum Ratings T A = 25 o C unless otherwise noted Electrical Characteristics T A = 25 o C unless otherwise noted SYMBOL I V V F PARAMETER Notes: 1. Single color light 2. Rth test condition: Mounted on PC Board FR 4 (pad size 2 ) PARAMETER Luminous Intensity Forward Voltage VALUES RATING R G B Storage Temperature -40 ~ +100 C Operating Temperature -40 ~ +100 C Reverse Voltage Continuous Forward Current Peak Forward Current (10% Duty Cycle, PW sec) Power Dissipation mw Junction Temperature C Junction/ambient (1 chip on 2 ) C/W Junction/ambient (3 chips on 2 ) C/W Junction/solder point (1 chip on) C/W Junction/solder point (3 chips on) C/W R G B Min Avg Avg Max UNIT mcd V CONDITIONS I F = 50 I F = 50 I R Reverse Current (max) µa V R = 5 V D Dominant Wavelength nm I F = 50 P Wavelength at Peak Emission nm I F = 50 2 ½ 50% Power Angle deg I F = 50 Spectrum Radiation Bandwidth nm I F = 50 5 UNIT V Page 2 of 8 Phone: (972) or (800) FAX: (972) visibleled@optekinc.com

3 Standard Bins (I F = 50 ) Lamps are sorted to luminous intensity (I V ) and dominant wavelength ( D ) bins shown. Orders for may be filled with any or all bins contained as below. RED Luminous Intensity (mcd) W 710 V 612 Dominant Wavelength (nm) 625 Luminous intensity is at V bin or above. GREEN Luminous Intensity (mcd) W 710 V 514 Dominant Wavelength (nm) 534 Luminous intensity is at V bin or above. BLUE Luminous Intensity (mcd) T 180 S 460 Dominant Wavelength (nm) 480 Luminous intensity is at S bin or above. Notes: 1. All ranks will be included per delivery, rank ratio will be based on the chip distribution. 2. Tolerance of measurement of luminous intensity is ±10%. 3. Tolerance of measurement of dominant wavelength is ±1 nm. 4. Tolerance of measurement of V F is ±0.05V. Phone: (972) or (800) FAX: (972) visibleled@optekinc.com Page 3 of 8

4 Typical Electro-Optical Characteristics Curves nm Relative Intensity vs Dominant Wavelength V Forward Current vs Forward Voltage V % % Relative Luminous Intensity vs Forward Current Page 4 of 8 Phone: (972) or (800) FAX: (972) visibleled@optekinc.com

5 Typical Electro-Optical Characteristics Curves C Maximum Forward DC Current vs Solder Point Temperature C 1 Chip On 3 Chips On C Maximum Forward DC Current vs Ambient Temperature C 50% Power Angle: 120 Far Field Pattern Phone: (972) or (800) FAX: (972) visibleled@optekinc.com Page 5 of 8

6 CIE Chromaticity Diagram Note: 1. The color coordinates of the mixed light can be expected within the area of the color triangle marked a). The achromatic point (x=0.33, y=0.33) is marked +. Page 6 of 8 Phone: (972) or (800) FAX: (972) visibleled@optekinc.com

7 Reel Dimensions: 13-inch reel Carrier Tape Dimensions: Loaded quantity 2000 pieces per reel Notes: sprocket hole pitch cumulative tolerance ±0.20 mm. 2. Carrier camber not to exceed 1 mm in 100 mm. 3. A 0 and B 0 measured on a plane 0.3 mm above the bottom of the pocket. 4. K 0 measured from a p lane on the inside bottom of the pocket to the top surface of the carrier. 5. All dimensions meet EIA-481-2A requirements. 6. Material: Black Anti-static Polystyrene. 7. Thickness: 0.305±0.02 mm. Phone: (972) or (800) FAX: (972) visibleled@optekinc.com Page 7 of 8

8 Moisture Resistant Packaging Label Aluminum Moisture-proof Bag Desiccant Bar Code Label Page 8 of 8 Phone: (972) or (800) FAX: (972) visibleled@optekinc.com