ARGUS RADAR Quick Reference Card

Transcription

1 ARGUS RADAR Quick Reference Card Own Ship Activated ERBL AIS Symbol ERBL 1 and 2 Helm or Antenna Position Ref. Parallel Index Status/Setup Display Presentation Transceiver Status Tuning Bar Presentation Reset (offset) Range Rings Vector Time Range Rings Heading line Sea/Ground Stabilization PPI Centre Status Audio Alarm

2 ARGUS RADAR Quick Reference Card ERBL Controls Video Processing Controls PPI Center/ Off Center Trackball Functions Push Buttons AIS/TT Controls Programmable User Function Keys Display Presentation Modes Range Scale EBL Knob Day Night Mode Audio Alarm VRM Knob Trackball Power On TX/ Stand-By System Failure Alarm Video processing adjustment sequence Sea clutter reduction Manual anti-sea clutter: Select this method when the sea clutter extension is symmetrical with almost the same intensity in every direction. Select the actual sea state on the Anti-Sea Clutter control bar and increase or decrease the control until clutter s residuals are comparable to the receiver noise level. Auto anti-sea clutter: Select this method in restricted areas or when the sea state is changing abruptly in different directions. Select auto from the Anti-Sea Clutter control bar list. Rain clutter reduction Manual anti-rain clutter: Select this method when you want to optimize land detection and rain reduction. Adjust the Anti-Rain control bar until the rain clutter level becomes comparable to noise with land reflections still visible. Auto anti-rain clutter: Select this method in heavy rain when it is not possible to discern between rain, sea and land clutter. Transmitted pulse Transmitted pulse is controlled by the range scale and the Power Boost setting. Gain Adjustment Manual: Adjust the level until only a few speckles of noise are visible. In clutter conditions, adjust it to reduce the false echoes after the clutter has been suppressed by anti-sea and anti-rain controls. It is preferable to adjust the gain manually in heavy clutter conditions. Auto: Gain is automatically changed until the optimal detection level on noise is reached. It will automatically display some speckles of noise, not to lose any targets. I.R. and Sweep to Sweep Correlation Interference Rejection is always enabled in the default setup. Use sweep/sweep correlation to completely clean up the picture from very strong interferences. Select Target enhancement to increase dimensions of small echoes. Scan to scan correlation Select this video processing when an additional reduction of interference is needed and to completely clean up the scanned picture from sea clutter residuals. Warning: Fast approaching targets can be cancelled depending on SC/SC level (2 or 3) target size and speed. Auto Sea/Rain (available only if Advanced Video Processing is enabled) When the function is on, a preset clutter removal strategy can be selected for the appropriate scenario. Options available are: Open Sea, Coast, Heavy Rain, Light Rain/Harbour. Adjust the intervention with the same progress bar. Gain progress bar is not working (except in Heavy Rain) and anti rain clutter is always set to Auto Rain.

3 Speed Source Menu Select the speed source. Enable/adjust Manual Drift. Select Navigation or Docking presentation. TXRX and Interswitch Menu (Optional) This type of configuration, which is only available in wide screen mode, has the characteristics of being able to combine up to four signals from TXRX transceivers with different antennas. A TXRX & Interswitch Menu (Standard) Select the radar transceiver. Enable Power Boost, Performance Monitor Orientation and Motion Mode Menu Select the Orientation and Motion modes of the PPI presentation. 6 Cursor Menu Activate ERBL 1 or 2. Reset ERBL in Center position. Change True or Relative modes and geo/own ship reference. B Graphic Symbols Menu Enable Target Tracks, AIS, Navigation symbols. Set and control parallel indexes. Enable own ship outline and AIS names/call sign. 7 8 Personal Settings Menu Set alternative options for the radar display. Configure the 3 Programmable Function Push buttons. Brilliance Settings Menu Setting the brilliance of various display elements and the Keyboard back light dimmer. Antares PCB Info Menu Display Main Processing Board information like lifetime, Serial Number and PCB monitored signals.

4 Radar Configuration Service Technician Menu: Entering this menu, a new window requesting a password will be displayed. C D E F G H I Configuration sharing menu Synchronization system parameters. 12 Tracking Menu AIS Interface enable. Minimum Safety Settings. Anchor watch enable. AIS and TT list for fast selection. Configure AIS Filtering and overflow priority. AIS Alarm disable checkboxes. L M Video Maps Menu Open, create, delete and transfer a map with an external mass storage device Preset Video Proc Menu Set preconfigured configurations of video processing for specific tasks. Day color Toggling this button, the operator can quickly adjust the Monitor background colour. The selection is between Night and Day options. The Night PPI background colour is very much darker than the Day setting. System Version Menu Installed Software version. (Version standard) ECDIS Menu (Optional) When the unit is configured to be connected to an ECDIS, a new button will be available in the lower part of the main menu. This menu only applies to network ECDIS systems. N Conning tasks menu This button is only available for the wide screen system. In this mode, the operator can configure the available areas on the System Data Area Section, entering the tasks to be set into the dedicated areas.

5 A B C D TXRX Data Menu Display Transceiver status and Operating timers. E Waypoints Data Menu Display waypoints geographic position of the route in the radar presentation. Anch Watch The Anchor Watch is a Radar Target only function, and it can be used when Own Ship is at anchor and it s needed to monitor if it moves excessively from its original position. G Tracking Data Fusion Menu Enable TT/AIS Association. Configure Association conditions. Select data source (AIS or TT). H AIS Targets Selection List Display received AIS. Used to order and select AIS by Ship Name or Range distance. F Radar Targets selection list Display Tracked Target ordered by number id, range or safety parameters (CPA/TCPA) by Ship Name or Range distance. Guard Zone Menu Setup for up to four guard/autoacquisition rings. Auto Acquire Zone Menu Setup for the own ship s autoacquisition zone. Min Safety This is a function for Radar targets and AIS which allows visualising and setting the threshold of CPA and TCPA that defines when a target will be considered dangerous. Select data source (AIS or TT). I L N Conning task Configuration list Available tasks Trial Manoeuvre Menu Simulate a ship manoeuvre according specific speed and course parameters. M USB Storage Menu Transfer a map with an external USB mass storage device. Map Editing Menu Build a map composed by lines, texts and symbols with selectable colors.

6 O 6 1 Trackball Function Help Line 2 Cursor Position Readout 3 Advanced Video Processing 4 Anti-Sea Clutter Control Bar 5 Scan to Scan Correlation 6 Range Scale Control/Status 7 Alarm List 8 Interference Rejection Settings 9 Anti-Rain Control Bar 10 Gain Control Bar 11 (Relative) Past Position Control 12 Echo Trails 13 Track/PPI Mode O Alarm List The alarms in the ALARM LIST window begin to flash, showing the time at which the alarm occurred. Once an alarm situation has been triggered, it can be acknowledged by clicking on it. Alarms, Warnings and Sys List Alarms/Failures History List with time event. The list displays the latest 100 messages.

7 Control Icons Helm or Antenna Position Distance Reference. Automatically set to Radar antenna when helm position is not available AIS Filtering Filtering type is indicated next to the funnel Heading line (hide) AIS Data Association On (AIS data source) Range Rings Disabled AIS Lost Alarm Audio Disabled AIS Danger Auto-activation Sea Stabilization/Ground Stabilization Parallel index status/setup System status/system failure Presentation Reset (off center) PPI Symbols Summary RADAR Tracked target in Initial state Anchor Watch Reference Target AIS Danger Target RADAR Tracked target in Steady state Trial Manoeuvre in execution AIS Lost Target RADAR Tracked target in Data Request state Radar Target Training in execution AIS Target in Data Request state RADAR Target Dangerous Target AIS Sleeping Target AIS Aton (Aid To Navigation) RADAR Tracked target in Lost state AIS Activated Target with no valid heading information Virtual AIS Aton (Aid To Navigation) R Auto Drift Reference Target AIS Activated Target with valid heading information AIS Search And Rescue Transponder

8 ARGUS RADAR Quick Reference Card Range Rings Own Ship Activated ERBL AIS Symbol AIS and TT Status Area Speed and Position information Display Presentation Zoom Window Area Selection Heading Line PPI Centre Status Tasks Area Additional PPI/ Zoom Transceiver Status Tuning Bar Range Rings System Status/ Failure Audio Alarm * *