MODBUS Protocol for CS101 network card family

Size: px

Start display at page:

Download "MODBUS Protocol for CS101 network card family"

Franklin Chandler
5 years ago
Views:

1 MODBUS Protocol for CS1 network card family 1

2 MODBUS tables Please note that not all the data are available for all UPSs. The addresses are in PLC mode (base 1). Type: U means without arithmetic sign, S means with arithmetic sign. Single phase UPS Address Function Type Description Notes UPS Company Name 2 each register UPS Model Name 2 each register UPS Firmware Version 2 each register CS1 Firmware Version 2 each register U Battery Status rmal 3 - battery low U Seconds on Battery [seconds] U Battery Capacity [%] U Battery Voltage [V * 0] 400 U Battery Temperature [ C * ] 401 S Battery Current [A * ] 402 U Total Battery Voltage [V * 0] U Input Line Voltage [V * ] U Input Max Line Voltage [V * ] U Input Min Line Voltage [V * ] U Input Frequency [Hz * ] U Input Current [A * ] U Input True Power [W] U Output Status rmal 3 - battery 4 - boost 5 - sleeping 6 - bypass 7 - rebooting 8 - standby 9 - buck U Output Voltage [V * ] U Output Frequency [Hz * ] U Output Load [%] U Output Current [A * ] U Output True Power [W] U Rating Voltage [V * ] U Rating Power [VA] U Rating Battery Voltage [V * 0] 2

3 40063 U Rating Frequency [Hz * ] U Utility Fail U UPS Failed U Test in Progress U Shutdown Active U Beeper ON / 16 U Config UPS Switch off Delay / 16 U Config UPS Sleep Time / 16 U Control UPS Switch off 2 - turn OFF UPS The delay in seconds the UPS remains on after being told to turn off. Allowed values are [seconds]: 12, 18, 24, 30, 36, 42, 48, 54, 60, 120, 180, 240, 300, 360, 420, 480, 540, / 16 U Control UPS Reboot 2 - reboot UPS / 16 U Control UPS Sleep 1 - no put UPS to sleep 2 - put UPS to sleep / 16 U Control Simulate Power Failure 2 - simulate Power Failure / 16 U Control Flash and Beep 2 - enable flash and beep / 16 U Control Turn ON UPS Load 2 - enable flash and beep / 16 U Test Diagnostics 2 - smart control turn ON UPS load U Test Diagnostics Results 1 - ok 2 - failed 3 - invalid test 4 - test in progress 3

4 Three-phase UPS Address Function Type Description Notes UPS Company Name 2 each register UPS Model Name 2 each register UPS Firmware Version 2 each register CS1 Firmware Version 2 each register U Battery Status rmal 3 - battery low U Seconds on Battery [seconds] U Output Status rmal 3 - battery 4 - boost 5 - sleeping 6 - bypass 7 - rebooting 8 - standby / 16 U Config UPS Switch off Delay / 16 U Config UPS Sleep Time / 16 U Control UPS Switch off 2 - turn OFF UPS 9 - buck The delay in seconds the UPS remains on after being told to turn off. Allowed values are [seconds]: 12, 18, 24, 30, 36, 42, 48, 54, 60, 120, 180, 240, 300, 360, 420, 480, 540, / 16 U Control UPS Reboot 2 - reboot UPS / 16 U Control UPS Sleep 1 - no put UPS to sleep 2 - put UPS to sleep / 16 U Control Simulate Power Failure 2 - simulate Power Failure / 16 U Control Flash and Beep 2 - enable flash and beep / 16 U Control Turn ON UPS Load 2 - smart control turn ON UPS load / 16 U Test Diagnostics 2 - start test diagnostic U Test Diagnostics Results 1 - ok 2 - failed 3 - invalid test 4 - test in progress 400 U Battery Voltage [V * ] 401 U Battery Capacity [%] 402 U Battery Time Remaining [minutes] 401 S Battery Current [A * ] 404 U Battery Temperature [ C * ] 401 U Input Frequency [Hz * ] U Input Voltage (L1) [V * ] U Input Voltage (L2) [V * ] U Input Voltage (L3) [V * ] U Output Frequency [Hz * ] 4

5 40121 U Output Voltage (L1) [V * ] Output Voltage if the UPS has only one U Output Voltage (L2) [V * ] U Output Voltage (L3) [V * ] U Output Load (L1) [% * ] Output Load if the UPS has only one U Output Load (L2) [% * ] U Output Load (L3) [% * ] U Bypass Frequency [Hz * ] U Bypass Voltage (L1) [V * ] U Bypass Voltage (L2) [V * ] U Bypass Voltage (L3) [V * ] 400 U DC and Rectifier Status RecRotError 401 U DC and Rectifier Status LowBatteryShutdown 402 U DC and Rectifier Status LowBattery 403 U DC and Rectifier Status 2 - one output phase InAndOut 3 - three output phases 404 U DC and Rectifier Status 4 - backup BatteryStatus 5 - AC normal 405 U 6 - boost DC and Rectifier Status 7 - float ChargeStatus 406 U DC and Rectifier Status RecOperating 407 U UPS Status Bypass 408 U Frequency Fail UPS Status Manual Bypass Breaker 409 U UPS Status AC Status U 401 U U U U UPS Status Static Switch Mode UPS Status Inverter Operating Fault Status Emergency Stop Fault Status High DC Shutdown Fault Status Bypass Breaker U Fault Status Over Load U U Fault Status Inverter Output Fail Fault Status Over Temperature 8 - closed 9 - open 8 - normal 9 - abnormal 12 - inverter mode 13 - bypass mode 5

6 40166 U Fault Status Short Circuit Rating Rectifier Voltage 2 each register Rating Rectifier U [Hz] Frequency Rating Source Bypass 2 each register Voltage Rating Bypass Source U [Hz] Frequency Rating Output Voltage 2 each register U Rating Output Frequency [Hz] U Rating Battery Voltage [V] Rating Power 2 each register

Modbus Register Map: InfraStruXure Symmetra 3-Phase Absolute Starting Register Number, (Decimal)

Modbus Register Map: InfraStruXure Symmetra 3-Phase Absolute Starting Register Number, (Decimal) Modbus Map: InfraStruXure Symmetra 3-Phase 990-3249 // Status Word 0 40000 0 8 Reserved R = UPS ready to provide power to the load upon return of normal line voltage or upon user command = State == Enable