Modbus Register Map: InfraStruXure Symmetra 3-Phase Absolute Starting Register Number, (Decimal)

Size: px

Start display at page:

Download "Modbus Register Map: InfraStruXure Symmetra 3-Phase Absolute Starting Register Number, (Decimal)"

Cleopatra Stafford
5 years ago
Views:

1 Modbus Map: InfraStruXure Symmetra 3-Phase // Status Word Reserved R = UPS ready to provide power to the load upon return of normal line voltage or upon user command = State == Enable Load Disconnect (Output is off - But not due to delayed wakeup command) 6 = UPS ready to provide power to the load upon user command = State == Load Disconnect (Output is off) (Number of modules!= 0) && (Bad Modules!= Installed Modules) = UPS in bypass mode as a result of manual bypass control = State == Manual Bypass (System bypass by front switch) 4 = UPS returning from bypass = State == Temporary Bypass (Bypass with intention of leaving bypass state) 3 = UPS in bypass due to command = State == Command Bypass (UPS Commanded into Bypass) 2 Reserved = UPS in bypass due to an internal fault (indicated through register or 40003) = State == Temporary Bypass (Bypass with no intention of leaving) 0 UPS turning on = State == Wakeup (Output turning on - Waiting for modules to start, processing system overrides) // Status Word Reserved R = UPS fault - internal temperature exceeded nominal limits Any battery is too hot (Cleared 2 minutes after battery cools off) 6 Reserved = Battery charger failure Any module has reported a charger fault (Cleared when no module has a charger failure) 4 = UPS in shutdown mode State == Enable Load Disconnect (Output is off - Waiting for power to return) 3 = UPS in sleep mode State == Enable Load Disconnect (Output is off - By sleep with delayed wakeup command) 2 Reserved = UPS unable to transfer to on-battery operation due to overload State == Load Disconnect (Output is off - No modules providing power to load, and bypass was not available) 0 = UPS output not receiving power due to low battery shutdown State == Enable Load Disconnect (Output is off - Due to low battery - Waiting for power to return) // Status Word Reserved R = UPS commanded out of bypass with no batteries connected UPS in bypass 0/200 UPS Fault - UPS commanded to leave bypass state but no batteries were connected InfraStruXure Symmetra 3-Phase Modbus Map

2 4 = UPS fault - UPS in bypass 3 = Output voltage selection failure UPS in bypass = UPS fault - output voltage select failure, UPS in bypass 2 Reserved Reserved 0 = Fan failure = UPS fault - UPS in bypass due to fan failure // Status Word Reserved R = Replace battery 6 = Low battery Low Battery Runtime <= Low Battery Setting ("j" <= "q") = Overload 4 = On battery = On battery - Any Module On Battery Battery Discharging Sim Power Failure UPS Doing Self Test Runtime Calibration 3 = Online 2 Reserved = Reboot/Sleep Mode Symmetra sets this bit when in Reboot or Sleep Mode 0 = Performing battery calibration discharge // Status Word Reserved R = Backfeed relay open (fault) 0 = Site wiring fault 9 = Fault found in register 40033, 40034, 4003, or Fault found in abnormal condition register (second abnormal condition register) 8 = Battery voltage high = No batteries 6 = System not synchronized = Output voltage out of range 4 = XR frame fault Extended Run (XR) frame fault 3 = Runtime below alarm threshold 2 = Load shutdown from bypass Input frequency or voltage outside limits = No good modules present 0 = Internal communication failure // Status Word 4000 = RIM is in control R 4 = System level fan failed 3 = Input CB tripped open = Input circuit breaker tripped open 2 = System is in maintenance bypass = UPS in bypass due to overload 0 = UPS in bypass due to internal fault 9 = Bypass contactor stuck in online position InfraStruXure Symmetra 3-Phase Modbus Map 2

3 // 8 = Bypass contactor stuck in bypass position = Bypass not in range (either frequency or voltage unacceptable) 6 = Redundancy below threshold = Loss of redundancy 4 = Load is above alarm threshold 3 = An installed battery has failed 2 = RIM is installed and failed = IM is installed and failed 0 An installed Power Module has failed Line Quality R WORD 00FF = Acceptable utility line quality 0000 = Unacceptable utility line quality 4000 % Battery Capacity R WORD % Runtime Remaining R WORD Min Battery Voltage R WORD V Present internal operating temperature (0-209 C) 00XX =Valid reading FFXX =Invalid reading 4000A 0 UPS Internal Temperature WORD (XX is sensor reading) 4000B Amps Drawn By Load R WORD A 4000C 2 Number of Battery Packs with Bad Batteries R WORD Variable ( 99) 4000D 3 Number of Battery Packs R WORD Variable ( 99) 4000E 4 % Power Drawn By Load R WORD % 4000F Maximum Input Voltage Since Last Reading R WORD V Minimum Input Voltage Since Last Reading R WORD V 400 Nominal Battery Voltage R WORD V Actual Battery Voltage R WORD V Utility Input Frequency R WORD Hz Utility Input Voltage Phase A R WORD V Utility Input Current Phase A R WORD A Bypass Input Voltage Phase A R WORD V Percent of Maximum Output VA s Phase n+0 R WORD % Percent of Maximum Output VA s Phase n+x R WORD % Output Phase A R WORD kva 400A 26 Output Voltage Phase A R WORD V 400B 2 Output Current Phase A R WORD A 400C 28 Peak Output Current Phase A R WORD A 400D 29 Utility Input Voltage Phase B R WORD V InfraStruXure Symmetra 3-Phase Modbus Map 3

4 400E 30 Utility Input Current Phase B R WORD A 400F 3 Bypass Input Voltage Phase B R WORD V Percent of Maximum Output VA s Phase n+0 R WORD % Percent of Maximum Output VA s Phase n+x R WORD % Output Phase B R WORD kva Output Voltage Phase B R WORD V Output Current Phase B R WORD A Peak Output Current Phase B R WORD A Utility Input Voltage Phase C R WORD V Utility Input Current Phase C R WORD A Bypass Input Voltage Phase C R WORD V Percent of Maximum Output VA s Phase n+0 R WORD % 4002A 42 Percent of Maximum Output VA s Phase n+x R WORD % 4002B 43 Output Phase C R WORD kva 4002C 44 Output Voltage Phase C R WORD V 4002D 4 Output Current Phase C R WORD A 4002E 46 Peak Output Current Phase C R WORD A 4002F 4 Measure-UPS Temperature Reading (sensor ) R WORD C Measure-UPS Humidity Reading (sensor ) R WORD % Measure-UPS Temperature Reading (sensor 2) R WORD C Measure-UPS Humidity Reading (sensor 2) R WORD % Reserved R WORD Reserved R WORD // Status Word Reserved R = Battery Charger Shut Down Externally 0 = System Startup Configuration Failed // Status Word = Static bypass switch module removed R 4 = UPS in forced bypass state 3 = System ID card failed 2 = System ID card removed = Static bypass switch module fault 0 = Internal DC disconnect switch tripped 9 = Switchgear communication card removed 8 = Switchgear communication card failure InfraStruXure Symmetra 3-Phase Modbus Map 4

5 // = XR communication card removed 6 = XR communication card failure = Battery monitor card removed 4 = Battery monitor card failure 3 = System power supply card failure 2 = External DC disconnect switch tripped = Isolation transformer over temperature 0 = Maintenance bypass failure 4003 Measure-UPS Contact Position R WORD Minimum Return Battery Capacity R WORD % Lower Transfer Point R WORD V 4003A 8 Upper Transfer Point R WORD V 4003B 9 Nominal Output Voltage R WORD V 4003C 60 Shutdown Delay R WORD Sec 4003D 6 Low Battery Duration R WORD Min 4003E 62 Turn On Delay R WORD Sec 4003F 63 Sensitivity R WORD Sensitivity UPS ID Character # R WORD UPS ID Character #2 R WORD UPS ID Character #3 R WORD UPS ID Character #4 R WORD UPS ID Character # R WORD UPS ID Character #6 R WORD UPS ID Character # R WORD 4004 UPS ID Character #8 R WORD Battery Current R WORD A F 3 9 Reserved R WORD 4000-FFFF INVALID ADDRESS InfraStruXure Symmetra 3-Phase Modbus Map

InfraStruXure Manager v4.x Addendum: Building Management System Integration

InfraStruXure Manager v4.x Addendum: Building Management System Integration Introduction This addendum explains the integration of the APC InfraStruXure Manager Appliance with a Building Management System