Planar Monolithics Industries, Inc.

Transcription

1 1

2 Planar Monolithics Industries, Inc. 2

3 TABLE OF CONTENTS PMI NEW RESEARCH & DEVELOPMENT PRESENTATION TABLE OF CONTENTS 1 Amplifiers 5 2 Attenuator Variable 25 3 Couplers, Dividers & Hybrids 42 4 DLVAs, ERDLVAs & SDLVAs 54 5 DTOs, Frequency Synthesizers & Frequency Doublers 83 6 Filters & Diplexers 97 7 Form, Fit & Function Products IFMs & Frequency Discriminators Integrated MIC/MMIC Modules I/Q Vector Modulators Limiters & Detectors Log Amplifiers 159 3

4 TABLE OF CONTENTS PMI NEW RESEARCH & DEVELOPMENT PRESENTATION TABLE OF CONTENTS 13 Pulse & Bi-Phase Modulators Phase Shifters Rack & Chassis Mount Products UP & Down Converters, Receiver Front Ends & Transceivers Single Sideband Modulators SMT & QFN Products Solid State Switches Switch Matrices Switch Filter Banks Threshold Detectors USB Products 272 4

5 1- AMPLIFIERS 5

6 LIMITING AMPLIFIER PEC3-40-1D6G2D7G-15LM-SFF Frequency Range 1.6 to 2.7GHz Noise Figure: 5.5dB +25C Gain: 35dB min. Gain Flatness: (over operating temperature) VSWR: Saturated Output Power: Input Power Range: Saturated Power Flatness: ±2.0dB max. - Over any 1GHz 2.0:1 max. +15dBm min. (±2dB) -25 to +5dBm min -30 to +5dBm goal ±1.5dB max. Harmonic Content: -15dBm min. -18dBm goal Reverse isolation: 50dB min. Pulse Response Overshoot: 0.4dB max. Settling Time: 15nsec max. Recovery Time: 50nsec max. Maximum Input Power: (No Damage) +25dBm CW DC Voltage Supply +12 to +15V DC Current Draw 400mA max. Connectors SMA(F) Sealing: Non-Hermetic Size 1.91" x 0.78" x 0.36" 6

7 LIMITING AMPLIFIER PEC3-40-1D6G2D7G-15LM-SFF POWER LEVEL 1.6 GHz 2.7 GHz -30 dbm dbm dbm dbm dbm dbm db, dbm

8 LIMITING AMPLIFIER PEC-85-0R32R5-15LM-12-SFF Frequency Range 0.3 to 2.5GHz Operating Input Power +10dBm CW max. Survival Input Power +15dBm CW max. Limited RF Output +15dBm ± 2.5dBm Noise Figure VSWR In / Out 5.0dB typ.. 2.0:1 max. VNA GAIN 82 db Typ. DC Voltage Supply +12VDC DC Current Draw 485mA typ. Connectors SMA(F) Size 5.0" x 1.5" x 0.51" Finish Gold Plated 8

9 LIMITING AMPLIFIER PEC-85-0R32R5-15LM-12-SFF LIMITED RF OUTPUT +15dBm ±2.5dB Input & Output Return Loss 9

10 LIMITING AMPLIFIER PEC2-2G18G-2DBM-LM-SFF Frequency Range Input Power Output Power Output power Variation vs. Input Power Noise Figure Spurious Performance Harmonic Performance VSWR In/Out 2.0 to 18.0GHz -50 to +30dBm CW +2.0dBm Nominal ±2.0dB max. 10dB max.. -60dBc typical -10dBc typical 2.0:1 max. Noise Figure DC Voltage Supply +12 to +15 DC Current Draw Connectors 460mA typical SMA(F) Size 2.98" x 0.78" x 0.36" 10

11 2.0 to 18.0 GHz, Limiting Amplifier PEC2-2G18G-21DBM-LM-SFF Frequency Range Input Power Output Power Output power Variation vs. Input Power OP1dB 2nd Harmonic Rejection Third Order Intercept VSWR In/Out Maximum Input Power 2.0 to 18.0GHz -45 to +10dBm CW +21.0dBm to +25dBm Nominal ±2.0dB max. over operating temperature 4dBm below Psat typical Psat 35dBm typical 2.0:1 max. +17dBm CW Saturated Output -45dBm DC Voltage Supply +15 DC Current Draw 700mA max. Connectors SMA(F) Size 2.98" x 0.78" x 0.36" 11

12 2.0 to 4.0GHz, Low Noise Amplifier PMI MODEL No: PEC-30-2G4G-21-8V-SFF Low Noise Amplifier designed for Military and Industrial applications. This amplifier is supplied in our EMI shielded hermetically sealed PE2 housing with SMA female connectors. This amplifier provides >30dB of Gain with a typical noise figure of 1.5dB and an OP1DB of +21 dbm minimum and operates from 2.0 to 4.0 GHz. This amplifier operates on a +8VDC supply (+8.5 V maximum) with a Typical DC current draw of 235 ma (Maximum of 380 ma). PARAMETERS SPECIFIED VALUE TEST RESULTS Frequency Range: 2 GHz 4 GHz 2 GHz 4 GHz Gain: 30dB Min db Gain Flatness: ±1.0dB Max. ±0.56 db Noise Figure: 1.5dB Typ db OP1dB: +21dBm Min dbm VSWR: (Input/Output) 2.0:1 Max Input: 1.67:1 Output: 1.29:1 Input Power: +12dBm CW Max. Pass DC Supply (See Note 1): +7.8 to 380mA Max VDC *Note 1: No internal voltage regulation or reverse voltage protection. +8.5VDC maximum or damage will occur. 12

13 2.0 to 4.0GHz, Low Noise Amplifier PMI MODEL No: PEC-30-2G4G-21-8V-SFF 13

14 9.0 to 10.0GHz, Low Noise Amplifier PEC-37-9G10G-3R0-27-SFF Frequency Range Nominal +25C Base Plate Temperature Gain Flatness Gain Variation over Temperature Noise Figure OP1dB 9.0 to 10.0GHz 34dB min., 40dB max. ±0.35dB typ., ±0.5dB max. ±2dB typical 2.5dB typ., 3.0dB max. +27dBm min., +28dBm typ. OIP3 +31dBm typ. VSWR In / Out 1.7:1 typ., 2.0:1 max. Spurious -60dBc max. DC Voltage Supply 400mA typ. Connectors SMA Female Size 1.5" x 1.0" x 0.4" Finish Nickel Plated 14

15 1.0 to 2.0GHz, Low Noise Amplifier PE2-35-1R02R0-1R SFF Frequency Range 1.0 to 2.0GHz Gain 35dB typ. Gain Flatness ±0.75dB typ. Noise Figure 1.4dB typ. OP1dB 17dBm typ. VSWR In/Out 2.0:1 typ. DC Voltage Supply +12 to +15 DC Current Draw 160mA typ. 15

16 1.0 to 2.0GHz, Low Noise Amplifier PE2-35-1R02R0-1R SFF GAIN AND RETURN LOSS NOISE FIGURE 16

17 10KHz to 40MHz Low Noise Amplifier PMI Model: PEC-60-10K40M-3R SFF GAIN Parameters Frequency Gain Gain Flatness Noise Figure VSWR (In/Out) OP1dB OIP3 DC POWER DC POWER DRAW Specification 10.0 KHz to 40.0 MHz +60dB ±1.0dB Max 3.5dB Max 1.8:1 Max +14dBm Min 21dBm ±12 to ±15 VDC 225 ma Max FREQ 10KHz 50KHz 100KHz 500KHz 1MHz GAIN

18 30MHz to 18GHz, Low Noise Amplifier PEC-38-30M18G-12-SFF PARAMETERS Frequency Range SPECIFIED VALUE 30 MHz to 18.0 GHz Gain +38 db TYP. Flatness +/- 2.0 db Max. Noise Figure 1dB Compression VSWR (In/Out) 5.0 db Max. +12dBm 2.2:1 Max. DC Supply 300mA Max. 18

19 30MHz to 18GHz, Low Noise Amplifier PEC-38-30M18G-12-SFF GAIN & RETURN LOSS Noise Figure 30MHz to 500MHz Noise Figure 500MHz to 18GHz 19

20 Small Signal, High Gain Amplifier with Bias-T at Output PE R SFF-BT Parameters Frequency Range Gain Gain Flatness Noise Figure Specified Value 2.0 to 18.0 GHz +30 db Typical +/-2.0 db Maximum 4.0 db Maximum 1dB Compression +20 dbm Minimum O1P3 VSWR In/Out Bias-Tee DC Power Supply +30 dbm Typical 2.0:1 Maximum Output SMA +12 to +15vdc 350mA Maximum 20

21 10MHz to 6GHz, Test Bench Amplifier Model: PLNA-30-10M6G-P1dB22-120VAC Frequency Range Gain Gain Flatness Noise Figure OP1dB 10 MHz to 6.0 GHz 30 db typ. - Measured 34.3 db ±2.0 db max. - Measured ±1.35 db 4.5 db typ., 5.25 db max. Measured 4.9 db +22 db min. - Measured db VSWR In/Out 2.0:1 typ. - Measured 1.99:1 Maximum RF Input: AC Voltage Supply AC Connector On/Off Switch RF Connector In/Out +10 dbm CW 110 VAC 3 Pin IEC Vandel Switch Illuminated N-Type Size 3.0" x 3.0" x 1.75" Finish Painted Blue 21

22 10MHz to 6GHz, Test Bench Amplifier Model: PLNA-30-10M6G-P1dB22-120VAC GAIN, FLATNESS, INPUT/OUTPUT RETURN LOSS 22

23 1.0GHz to 40GHz, Test Bench Amplifier Model: PTB-42-1G40G FF-DC12 PMI Model PTB-42-1G40G FF-DC12 is a portable amplifier that operates over the 1.0 to 40.0GHz frequency range. This model provides 40dB of typical gain with an OP1dB of +22dBm typical (1-18GHz) and +18dBm typical (18-40GHz). This amplifier features an on / off switch that is located on the front panel. This amplifier can operate on either 120VAC or via an external +12VDC supply. Frequency Range Gain Gain Flatness Noise Figure OP1dB VSWR In/Out Maximum RF Input: AC Voltage Supply 1.0 to 40.0GHz 40dB typ. ±2.5dB typ. 5.0dB typ. mid-band +22dBm typ. (1-18GHz) +18dBm typ. (18-40GHz) 2.5:1 typ. +15dBm 120VAC DC Voltage Supply (External) +12VDC 23

24 1.0GHz to 40GHz, Test Bench Amplifier Model: PTB-42-1G40G FF-DC12 24

25 2 - ATTENUATORS - VARIABLE 25

26 MINIATURE VOLTAGE VARIABLE ATTENUATOR PMI MODEL : VVA-1G4G-15-5-CD-1 PARAMETERS FREQENCY INSERTION LOSS ATTENUATOR RANGE ATTENUATOR 0dBm 0dB Attenuation Input RF Power for 0.25dB Compression Control Voltage SPECIFICATIONS 1.0 to 4.0 GHz 2.0 db Typ Insertion Loss to 15dB Min. ±0.5dB Typ 2.0:1 Typ +4dBm Typ. 0 to 5VDC 26

27 PMI MODEL: DTA-14G40G-32-CD-2 DIGITALLY VARIABLE ATTENUATOR 14.0 to 40.0 GHz Frequency Range Single +15VDC Operation >32dB Attenuation Range Fast Switching Speeds Frequency Range Mean Attenuation Range LSB Insertion Loss VSWR Operating Input P1dB Attenuation Flatness Attenuation Accuracy Switching Speed Digital Control DC Voltage DC Connector 14.0GHz to 40.0GHz 32dB Min. 0.4dB 9.0dB Max. 2.0:1 Max. +10dBm Typ. 10dB Attenuation 20dB Attenuation 30dB Attenuation 0 to 10dB Attenuation 10 to 20dB Attenuation 20 to 30dB Attenuation 1usec Max. ON Measured 120ns 0.5usec Max. OFF Measured 120ns 10-BIT Binary TTL 100mA Max - Measured 41mA 15 Pin Micro-D Female (Mating Connector Supplied) RF Connectors 2.92mm Female Size 2.0 x 1.8 x

28 PMI MODEL: DTA-14G40G-32-CD-2 DIGITALLY VARIABLE ATTENUATOR Delay ON 200nS/Div. Delay OFF 200nS/Div. 28

29 PMI MODEL: DTA-100M40G-30-CD-1 DIGITALLY VARIABLE ATTENUATOR 100MHz to 40.0 GHz Frequency Range Single +15VDC Operation 30dB Attenuation Range Low Insertion Loss Frequency Range Mean Attenuation Range LSB Insertion Loss VSWR Operating Input P1dB Attenuation Accuracy Switching Speed Digital Control DC Voltage 100MHz to 40.0GHz 30dB 1.0dB 5.0dB Typ. (Up to 20GHz) 8.0dB Typ. (Up to 40GHz) 2.5:1 Max. +20dBm Typ. ±2.5dB Typ. 1usec Max. ON 0.5usec Max. OFF 5-BIT Binary TTL 50mA Max DC Connector 15 Pin Micro-D Female (Mating Connector Supplied) RF Connectors 2.92mm Female Size 2.0 x 1.8 x

30 PMI MODEL: DTA-100M40G-30-CD-1 DIGITALLY VARIABLE ATTENUATOR RISE TIME: 42.5nS Delay ON: 266.0nS FALL TIME: 64.0nS Delay OFF: 129.5nS 30

31 PMI MODEL: PDVAN OPT25DBM OCTAVE BAND, DIGITALLY VARIABLE ATTENUATOR +25 dbm Minimum RF Power Handling 8.0 to 18.0 GHz Frequency Range <4.0 db Insertion Loss 60dB Attenuation Range Frequency Range Mean Attenuation Range LSB Insertion Loss VSWR Survival Power Rating Operating Input Power Attenuation Flatness 8.0GHz to 18.0GHz 60dB 0.25dB 4.0dB Goal, 5.0dB Max. 2.0:1 Max. +30dBm CW Max. +25dBm CW Min. 10dB Attenuation 20dB Attenuation 40dB Attenuation 60dB Attenuation Switching Speed Digital Control Input Tracking DC Voltage DC Connector 800nsec Max. 8-BIT Binary TTL Monotonic mA Max / -12 to 75mA Max. 15 Pin Micro-D Female (Mating Connector Supplied) RF Connectors SMA Female Size 2.00 x 1.80 x

32 PMI MODEL: PDVAN OPT25DBM OCTAVE BAND, DIGITALLY VARIABLE ATTENUATOR Delay ON nS Delay OFF 657.0nS 32

33 PMI MODEL: DTA-1G18G-60-CD-2 DIGITALLY VARIABLE ATTENUATOR 60dB Dynamic Range 1.0 to 18.0 GHz Frequency Range 4.5dB Insertion Loss Max. VSWR 2.0:1 Frequency Range Mean Attenuation Range Insertion Loss VSWR Attenuation Flatness Attenuation Accuracy 1.0GHz to 18.0GHz 60dB 4.5dB max 2.0:1 max ±1.0dB 20dB Attenuation ±1.25dB 40dB Attenuation ±3.0dB 60dB Attenuation 0dB to 20dB Attenuation 20dB to 40dB Attenuation 40dB to 60dB Attenuation Minimum Attenuation Step 0.06dB Operating Power 15dBm typ Survival Power 1W average from -65 ºC to +25 ºC Switching Time: On Time 1.0usec Max. (0.31usec Measured) Off Time DC Power Supply Connectors Weight Finish Logic Input 0.5usec Max. (0.06usec Measured) 100mA max 2 SMA & 15 PIN D-Sub Shipped with mating D-Sub 3.0oz (85g) approx. Painted Gray Logic "0" (Bit Off): -0.3 to +0.8V 33

34 DIGITALLY TUNED ATTENUATORS PMI MODEL DTA-2G18G-60-CD-1 PARAMETERS FREQUENCY ATTENUATION RANGE INSERTION LOSS VSWR FLATNESS ATTENUATION ACCURACY SURVIVAL POWER SWITCHING TIME DC POWER SPECIFICATIONS 2.0 TO 180 GHz 60dB 4.5dB Max 2.0:1 20dB = ±1.0dB 40dB = ±1.25dB 60dB = ±3.0dB Typ 0dB to 20dB = ±1.0dB Typ 20dB to 40dB = ±1.5dB Typ 40dB to 60dB = ±2.0dB Typ 2 Watt AVERATE -65ºC to + 25ºC 1µS Typ +/- 100mA Max 34

35 DIGITALLY TUNED ATTENUATORS PMI MODEL DTA-2G18G-60-CD-1 Delay On: nS Delay Off: nS 35

36 DIGITALLY TUNED ATTENUATORS PMI MODEL DTA-0R5G4G-60-CD-1 PARAMETERS FREQUENCY ATTENUATION RANGE INSERTION LOSS VSWR FLATNESS ATTENUATION ACCURACY MINIMUM ATTENUATION STEP SURVIVAL POWER SWITCHING TIME DC POWER SPECIFICATIONS 0.5 to 4.0 GHz 60dB 2.7dB Max 1.8:1 20dB = ±0.5dB 40dB = ±0.75dB 60dB = ±1.0dB Typ 0dB to 20dB = ±1.0dB Typ 20dB to 40dB = ±1.5dB Typ 40dB to 60dB = ±2.0dB Typ 0.06dB 2 Watt AVERATE -65ºC to + 25ºC 1µS Typ +/- 100mA Max 36

37 DIGITALLY TUNED ATTENUATORS PMI MODEL DTA-0R5G4G-60-CD-1 Delay On: 750.0nS Delay Off: 262.0nS 37

38 SWITCH BIT ATTENUATOR SAA-500M18G-20DB-SFF Frequency Range Attenuation Insertion Loss Switching Speed 500MHz to 18GHz 20dB ± 2.75dB nominal 3.0dB max. 100nsec max. TTL Control "1" = Insertion Loss "0" = 20dB Attenuation VSWR Input Power DC Supply Connectors 2.0:1 max. +20dBm CW max. +5V, 40mA typ. & -5V, 40mA typ. SMA (F) Size 1.0" x 0.70" x 0.35" Finish Painted Gray 38

39 SWITCH BIT ATTENUATOR SAA-500M18G-20DB-SFF ATTENUATION & RETURN LOSS (IN/OUT) 39

40 Programmable, 60dB, DC to 2.0GHz, Switch Bit Attenuator, SBA-DC2G-60DB-5V PARAMETERS SPECIFIED VALUE Frequency Range: DC to 2GHz Individual Cell Attenuation Total Attenuation Attenuation Accuracy Impedance: Switching Speed: 4dB, 8dB, 16dB, and 32dB 0 to 60dB ±0.3dB or 1% to 1GHz ±0.5dB or 2% or 2GHz 50Ω < 6ms VSWR: < 1.3:1 (17dB Return Loss) Power Handling: Operating Voltage 0.5W (27dBm) CW 5V 40

41 Programmable, 60dB, DC to 2.0GHz, Switch Bit Attenuator, SBA-DC2G-60DB-5V INSERTION LOSS TO 32dB 0vdc to 5vdc 32dB TO INSERTION LOSS 5vdc to 0vdc 41

42 3 - COUPLERS, DIVIDERS & HYBRIDS 42

43 5.3 TO 6.0GHz, QUADRATURE COUPLER PMI MODEL: QC-5D3G6G Frequency Range Insertion Loss Amplitude Balance Phase Balance 5.3 to 6.0GHz 1.0dB Maximum ±0.7 db Maximum ±5.0 Degrees Maximum Isolation 18dB Minimum VSWR Impedance Connectors 1.4:1 Maximum 50 Ohms SMA Male Size 1.25" x 0.75" x 0.37" Finish Painted Gray 43

44 5.3 TO 6.0GHz, QUADRATURE COUPLER PMI MODEL: QC-5D3G6G J2-J3 PHASE 0 º IN REFERENCE TO J1-J4 J2-J4 PHASE 90 º IN REFERENCE TO J1-J4 44

45 0.5 to 18.0 GHz, POWER DIVIDER APD YR1 Rev. B PARAMETERS SPECIFIED VALUE Frequency Range 0.5 GHz 18.0 GHz Insertion Loss GHz: 1.85dB Typ GHz: 3.5dB Typ VSWR GHz: 1.5:1 Typ GHz: 1.6:1 Typ. Isolation GHz: 16.5dB Typ GHz: 21.0dB Typ. Amplitude Balance GHz: ±0.2dB Typ GHz: ±0.45dB Typ. Phase Balance GHz: ±4 Typ GHz: ±5 Typ. 45

46 4-WAY POWER DIVIDER With 0º, 90º, 180º & 270º Outputs PMI MODEL: PD-CD SPECIFICATIONS: Frequency 0.3 to 9.9 GHz Phase Balance ±7º Max. Amp Balance ±0.5dB Max. Insertion Loss 8dB Max. RF Input Power 28W CW VSWR 2.0:1 Max. J2 0º J1 RF IN J3 90º J4 180º J5 270º 46

47 4-WAY POWER DIVIDER With 0º, 90º, 180º & 270º Outputs PMI MODEL: PD-CD Phase, Reflection Coefficient & Insertion Loss J1-J2 J1-J3 J1-J5 J1-J4 47

48 4-WAY AMPLIFIED POWER DIVIDER PMI MODEL: APD-4-20M6G-28V PMI MODEL NUMBER APD-4-20M6G-28V IS A 4-WAY AMPLIFIED POWER DIVIDER MODULE FOR USE OVER THE FREQUENCY RANGE OF 20 MHz TO 6.0 GHz WITH 3.5 db OF GAIN, AND A TYPICAL OUTPUT P1dB OF 9 dbm. THIS MODEL IS DESIGNED TO HAVE A LOW NOISE FIGURE OVER A BROAD FREQUENCY RANGE. Frequency Range Gain VSWR 20 MHz to 6.0 GHz 3.5 db, ±2 db max 2.5:1 max Noise figure 5.5 db (70 to 3000 MHz) max 6 db (20 to 6000 MHz) typ Output Power P1dB 10 dbm (20 to 3000 MHz) typ 9 dbm (3.0 to 6.0 GHz) typ Input Power Power Supply 33 dbm max (Survival) ma max Size 2.00" x 2.00" x 0.40" Finish Painted Blue 48

49 4-WAY AMPLIFIED POWER DIVIDER PMI MODEL: APD-4-20M6G-28V 49

50 8-WAY, POWER DIVIDER PMI MODEL: APD-8-30M6G-SFF PMI MODEL APD-8-30M6G-SFF is a 30 MHz to 6.0 GHz amplified 8 way power divider module. This module provides a nominal insertion loss of 6 db with a typical flatness of ±1 db over the operating frequency range. Over 36 db of reverse isolation is provided with a typical noise figure of 6.5 db and an input 1 db compression of -2.5 dbm. Input and Output VSWR is less than 2.0:1 into 50 OHM impedance. The DC supply required is +12 to +15 volts and current draw is typically 48 ma. Field removable SMA female connectors are utilized in a housing measuring 4.5 x 4.3 x 0.5. Frequency Range Outputs (J1-J8) to input (J9) Isolation Insertion Loss Insertion Loss Flatness Noise Figure VSWR (In/Out) Input P1 db Power Rating Connectors In/Out DC Voltage Finish 30 MHz to 6.0 GHz 32 db min. 36 db nominal 4 db min. 6 db nominal 8 db max. ±1 db typ. 6.5 db typ. 2.0:1 max dbm typ. +10 dbm max.* SMA(F) +12 to ma nominal Painted Blue 50

51 8-WAY, POWER DIVIDER PMI MODEL: APD-8-30M6G-SFF Typical Insertion Loss vs VSWR Typical Port to Port Isolation Ins. Loss 6.5dB Worse Case 13dB Typ. VSWR 2.0:1 Max 51

52 8-WAY, 40 WATT POWER DIVIDER PMI MODEL: APD-8-3D13D5-40W-SF PMI MODEL APD-8-3D13D5-40W-SFF IS A 3.1 GHz TO 3.5 GHz 8-WAY POWER DIVIDER THAT OFFERS MAXIMUM INSERTION LOSS OF 0.6 db WITH 23 db MINIMUM PORT TO PORT ISOLATION. THIS POWER DIVIDER IS PORT TO PORT PHASE MATCHED WITHIN ±2. FIELD REMOVABLE SMA FEMALE CONNECTORS ARE OFFERED IN A HOUSING MEASURING 4.10 x 2.15 x Frequency Range 3.1 to 3.5 GHz Insertion Loss <= 0.6 db - Measured 0.27 Isolation >= 23 db - Measured VSWR Input: <=1.3:1 - Measured 1.21:1 Output: <=1.2:1 - Measured 1.15:1 Amplitude Balance <= ±0.2 db - Measured -0.07, Phase Balance <=2 - Measured 0.65, Power Handling Impedance Port Connectors Finish Forward <= 40 Watt Reversed <= 1 Watt 50 Ohms SMA(F) Painted Blue 52

53 8-WAY, 40 WATT POWER DIVIDER PMI MODEL: APD-8-3D13D5-40W-SF PMI MODEL APD-8-3D13D5-40W-SFF IS A 3.1 GHz TO 3.5 GHz 8-WAY POWER DIVIDER THAT OFFERS MAXIMUM INSERTION LOSS OF 0.6 db WITH 23 db MINIMUM PORT TO PORT ISOLATION. THIS POWER DIVIDER IS PORT TO PORT PHASE MATCHED WITHIN ±2. FIELD REMOVABLE SMA FEMALE CONNECTORS ARE OFFERED IN A HOUSING MEASURING 4.10 x 2.15 x

54 4 - DLVAs, ERDLVAs & SDLVAs 54

55 CW Immune, Extended Range DLVA ERDLVA-218-CW-LPD-100 Frequency Range Frequency Flatness TSS Maximum Noise VSWR: Maximum Input Power (No Damage) Log Slope Video Output Range DC Offset Log Range Log Linearity Pulse Range Propagation Delay Rise Time Settling Time to ±1dB Recovery Time Duty Cycle CW Immunity Range Pulse Considered "CW" Baseline Shift Rejection Time Droop Power Supply Maximum DC Power Weight +95 C Package Finish 2.0 to 18.0GHz ±2.0 db max. -64dBm min. 100mV RMS with input terminated 2.0:1 max. +30dBm CW +50dBm Peak Pulse, 1% Duty Cycle, 10usec 77mV/dB (±5mV) into a 100 Ohm Load -0.5V (-60dBm) < RF IN < 5.5V (4dBm).±150mV -60 to +4dBm min. ±1.5dB (-20 C to +85 C) max. ±1.75dB (-54 C to +95 C) max. 200nsec to 20usec 30nsec 35nsec max. (20nsec typ) 50nsec 500nsec max (200nsec typ) 80% at maximum pulse width 50% at minimum pulse width TSS to -40dBm 900usec 25mV max. 1msec 1dB max. ±10.8V to ±12.5V 3.9 watts (Both supplies) 8oz max (3 oz. typ) >75,000 hours Hermetically sealed Mil-Spec Epoxy Paint, Gray Color 55

56 CW Immune, Extended Range DLVA ERDLVA-218-CW-LPD-100 ERDLVA-218-CW-LPD-100 Into a 100Ohm Load Tabulated Data 56

57 CW Immune, Extended Range DLVA ERDLVA-218-CW-LPD-100 ERDLVA-218-CW-LPD-100 Into a 100 Ohm Load Propagation 10GHz 10GHz into Ohm Load 57

58 CW Immune, Extended Range DLVA ERDLVA-218-DC-LPD Frequency Range Logging Range TSS Logging Slope Logging Linearity Flatness Output Stability Pulse Width Range Input VSWR (50 Ohms) 2.0 to 18.0GHz -60 to +4dBm -64dBm max +85mV/dB ±0.5dB typ, ±1.0dB max ±1.5dB ±1.0dB 50nsec to CW 3.0:1 max Video Load Impedance Video Rise Time Recovery Time DC Power 75 Ohms 20nsec 500nsec +12 to 190mA max -12 to 100mA max 58

59 CW Immune, Extended Range DLVA ERDLVA-218-DC-LPD 25ºC 59

60 PMI MODEL: GMDA-CW Detector Log Video Amplifier (DLVA) Frequency Range Output Voltage Flatness TSS Video Test Output 0.5 to 18.0GHz ±0.5V Across the band -43dBm min (10MHz Video Bandwidth) Fixed 450mV ±100mV DC Offset of Test Output +1.2V ±10% Impedance Log Slope Input Power -40 to -10dBm Input Power -10 to 0dBm Input Power 0 to +20dBm Log Linearity Input Power -40 to -10dBm Input Power -10 to 0dBm Input Power 0 to +20dBm Input Power Input VSWR Output Impedance Output Load Minimum Input Pulse Width Maximum Pulse Width Rise Time(10% to 90%) Recovery Time Meet all requirements with 50 OHM load 280mV/dB with ±12mV/dB tolerance Transition from 280mV/dB tolerance 0mV/dB with ±12mV/dB tolerance ±1.0dB Transition from 280mV/dB to 0mV/dB ±1.0dB +25dBm CW max (no damage) 2.5:1 (-40dBm to -10dBm) 1K OHM 1M OHM 100ns 150us DC Offset +1.35V ±10% Dynamic Range Power Supply Connectors 50ns max, Measured at input of -35dBm 5us max, At input pulse of -10dBm with pulse width of 150 us 63dB (-43 to +20dBm) +15V 75mA -15V 75mA SMA(F) Size 2.3" x 2.3" x 0.47" Finish Nickel Plating 60

61 DETECTOR LOG VIDEO AMPLIFIER (DLVA) PMI MODEL: PLVA-500M18G-50 PARAMETERS FREQUENCY FREQUENCY FLATNESS LOGGING RANGE USEFUL RANGE LOG LINEARITY ERROR LOG SLOPE TEMPERATURE STABILITY PULSE RESPONSE RISE TIME SETTLING RECOVERY TIME TSS VSWR Max RF INPUT DC Power Supply SPECIFICATIONS 500MHz to 18GHz ±1.0dB Max -40 to 0dBm Min -40 to =5dBm ±0.5dB 25C ±1.0dB Average (-54C to +85C) 50mV/dB ±4% of Average Slope ±1.0dB Max (-54C to +85C) 50nS to CW 20nS Max 45nS Max 150nS Typ 300nS Max -42dBm Min 3.0:1 Max +15dBm 75mA Max 61

62 DETECTOR LOG VIDEO AMPLIFIER (DLVA) PMI MODEL: PLVA-500M18G-50 Log Transfer vs. +25ºC Rise / Fall & Settling +25ºC / 0dBm 18 GHz 62

63 40dB, SUCCESSIVE DETECTION LOG VIDEO AMPLIFIER (SDLVA) PMI MODEL: SDLVA-8G18G-40-5-SFF 8.0 to 18.0 GHz SDLVA 40dB Dynamic Range Hermetically Sealed Miniature 1.2 X 0.85 X 0.40 PARAMETERS Frequency Range Frequency Flatness Log Linearity over Temperature Logging Range Input VSWR Max RF INPUT POWER SPECIFICATIONS 8 to 18 GHz ±2.0dB ±1.0dB -54C to +85C -40 to +0dBm 2.5:1 Max +10dBm CW Log Video Output Voltage 10mV to 2.25V Log Video Output Slope Log Video Output Rise Time Log Video Output Fall Time Log Video Recovery time DC Power Supply 50mV/dB 25nS - 20dBm 30nS - 20dBm 40nS - 20dBm 130mA Max 63

64 40dB, SUCCESSIVE DETECTION LOG VIDEO AMPLIFIER (SDLVA) PMI MODEL: SDLVA-8G18G-40-5-SFF LOG TRANSFER AND RISE / FALL +25ºC & 0dBm 64

65 18GHz to 40GHz, 65dB, 60nS Recovery, Successive Detection Log Video Amplifier (SDLVA) PMI MODEL: SDLVA-18G40G-65-CD-292FF VSWR 25C & -20dBm Frequency Range 18.0 to 40.0GHz TSS 25ºC Input Power Handling 10dBm max Video Log Range -63dBm to +2dBm Video Log Linearity +/- 25ºC +/-3.0 over temp Video Log Slope 25mV/ db nom Video Log Intercepts Video Output at 2dBm 1940mV max 1476mV max Video Output at -63dBm 280mV max 65mV min Video Frequency Flatness +/-2.5dB 25ºC Pulse Width Range Video Rise Time Recovery Time Delay Time Video Output Impedance 20ns to CW 11nS (8nS typ) 60nS (40nS typ) 15nS (5nS typ) 7nS over temp typ 50 ohms Input VSWR (50 ohms) 2.5:1 DC Power Supply *Note: Do not supply +V without -V supplied as well as this may destroy the unit 400mA 200mA Size 2.37" x 1.8" x 0.42" Finish Nickel Plate per SAE AMS

66 18GHz to 40GHz, 65dB, 60nS Recovery, Successive Detection Log Video Amplifier (SDLVA) PMI MODEL: SDLVA-18G40G-65-CD-292FF LINEARITY ERROR vs INPUT POWER +25C = -68dBm VIDEO OUT vs INPUT POWER RISE +25C/+2dBm RECOVERY +25C/+2dBm DELAY +25C/+2dBm 66

67 PMI MODEL: SDLVA-3G18G-CW-70-MAH CW-IMMUNE, SUCCESSIVE DETECTION LOG VIDEO AMPLIFIER (SDLVA) PMI Model No: SDLVA-3G18G-CW-70-MAH is a CW- Immune Successive Detection Log Video Amplifier operating in the 2.0 to 18.0GHz frequency band. It features an SPST on the RF output which allows for the RF to be blanked when the RF input signal is below the - 64dBm threshold. In addition to RF blanking, a 3.3V TTL-compatible output is also provided for time-gating or sampling to assist in digital system integration. Frequency Range Frequency Flatness TSS Limited Output Power VSWR Linear Output Gain Linear Output Psat V0 (Video Comparator Signal Amplitude) Video Comparator Delay Video Comparator Threshold Level V1 (Log Video Signal Amplitude) Log Slope Log Range Log Linearity Pulse Range Rise Time Settling Time to ±1dB Recovery Time CW Immunity Range 2.0 to 18.0GHz ±2.0 db max. -68dBm min., -70dBm typ 6.5dBm ±3.0dB max. 2.0:1 max 43db ±3.0dB max. 3dBm ±3.0dB max. 3.3V typ 50ns typ -64dBm ±3.0dB max. 1 Volt max 10mV/dB into a 50 ohm Load (±1mV) max -65 to +5dBm min ±1.75dB ( -40ºC to +85 ºC) max 100ns to 250 us 35ns max 50ns typ 200ns max (150ns typ) TSS to -45dBm (1dB degradation) Pulse Considered "CW" 1ms typ Rejection Time 1ms typ Droop 1dB max SPST Isolation 70dB typ SPST Switch Speed 20ns typ Power Supply ±12 VDC to ±15 VDC Connectors SMA Female Finish Gold Size 2.30" x 2.20" x 0.36" 67

68 PMI MODEL: SDLVA-100G18G-CW-70-MAH CW-IMMUNE, SUCCESSIVE DETECTION LOG VIDEO AMPLIFIER (SDLVA) PMI Model No. SDLVA-100M18G-CW-70-MAH is a CW-Immune, Successive Detection Log Video Amplifier operating in the 100MHz to 18.0GHz frequency band. It features an SPST on the RF output which allows for the RF to be turned off when the RF signal is below the adjustable threshold setting. In addition, the output switch can be controlled externally by enabling the external trigger. Furthermore, an LVTTL output is provided for time-gaiting or sampling to assist in digital system integration. 68

69 PMI MODEL: SDLVA-100G18G-CW-70-MAH CW-IMMUNE, SUCCESSIVE DETECTION LOG Frequency Range VIDEO AMPLIFIER (SDLVA) TYPICAL VIDEO OUTPUT vs INPUT POWER ALL TEMPERATURE LEVELS Frequency Flatness TSS Limited Output Power VSWR Linear Output Gain Linear Output Psqt V0 (Video Comparator Signal Amplitude) Video Comparator Delay Video Comparator Threshold Level V1 (Log Video Signal Amplitude) Log Slope Log Range Log Linearity Pulse Range Rise Time Settling Time to ±1dB Recovery Time CW Immunity Range Pulse Considered "CW" Rejection Time Droop SPST Isolation SPST Switch Speed SW CTL A (Enable) 100MHz to 18.0GHz ±2.0 db max. -68dBm min., -70dBm typ 8.0dBm ±3.0dB max. (Input Power >= -65dBm) 2.0:1 max 43db ±3.0dB max. 3dBm ±3.0dB max. 3.3V typ 50ns typ Adjustable with Analog Voltage -60dBm ±3.0dB max. 1 Volt max 10mV/dB into a 50 ohm Load ±1mV max -65 to +5dBm min ±1.75dB ( -40ºC to +85 ºC) max 100ns to 250 us 35ns max 50ns typ 350ns max TSS to -45dBm (1dB degradation) 1ms typ 1ms typ 1dB max 70dB typ 20ns typ LVTTL 0: Internal Comparator Triggered SPST LVTTL 1: External Trigger Enable (SW CTL B) SW CTL B (Trigger) LVTTL 0: SPST Switch On (Insertion Loss) LVTTL 1: SPST Switch Off (Isolation) Power Supply ±12 VDC to ±15 VDC Connectors SMA Female Finish Gold Size 2.30" x 2.20" x 0.36" 69

70 PMI MODEL: SDLVA-2020-OPT to 12.0GHz, SUCCESSIVE DETECTION LOG VIDEO AMPLIFIER (SDLVA) with DIGITAL LOG VIDEO OUTPUT Frequency Range Frequency Flatness TSS VSWR Logging Range Log Linearity Log Slope Log Temperature Stability Rise Time (10% to 90%) 1.0 to 12.0GHz ±2.0dB typ, ±2.5dB max -65 dbm max 3.0:1 max -20 dbm) -65dBm to -35dBm ±1.75 db Maximum (-65dBm to -35dBm) 5 LSB/dB nominal ±1.75dB (0 C to 60 C) 20nS max Recovery Time Output Power Power Supply 200nS max +10dBm ±2.5dB typ 700mA max 200mA max Size 3.5" x 3.0" x 0.5" Finish ADC Clock Rate(J4) Painted Blue 100MHz Digital Log Video Output LVTTL Logic Output LVTTL Comparator Delay LVTTL Threshold Level Video Output Power/ Logic Connector 8-Bit LVTTL 3.3V typ 50ns typ Adjustable (Analog) -60dBm ±3dB typ Lowest Level 8 Bit 3.3 V LVTTL 15 Pin Micro-D Male 70

71 PMI MODEL: SDLVA-2020-OPT to 12.0GHz, SUCCESSIVE DETECTION LOG VIDEO AMPLIFIER (SDLVA) with DIGITAL LOG VIDEO OUTPUT VIDEO OUTPUT vs INPUT POWER OUTPUT POWER -65 dbm INPUT POWER OUTPUT POWER -35 dbm INPUT POWER 71

72 PMI MODEL: SDLVA MV SUCCESSIVE DETECTION LOG VIDEO AMPLIFIER (SDLVA) Frequency Range 2.0 to 18.0GHz PMI Model No. SDLVA M is a Detector Log Video Amplifier (DLVA) designed to operate over the 2.0 to 18.0GHz frequency range. This model offers a logging range of -40 to +4dBm having a log slope of 70mV / db. The logging linearity is better than ±0.75dB and the rise time is 25nsec maximum and the fall time 300nsec maximum. This model operates on ±15VDC and is supplied in a small housing measuring only 2.2" x 1.5" x 0.4". Logging Range TSS Logging Slope Logging +25C Flatness Maximum Input Power -40 to +4dBm -42dBm max +70±3mv/dB maximum ±0.75dB maximum (-40 to 0dBm) ±1.5dB maximum +20dBm Video Load Impedance Video Rise Time Video Fall Time Recovery Time Pulse Width Range DC Offset at RF Terminated Noise at RF Terminated Mode 50 ohms 25nsec maximum 300nsec maximum 500sec maximum 50nsec to CW minimum ±70mV maximum 150mV P-P maximum DC Coupled Primary Power 200mA maximum 150mA maximum Size 2.2" x 1.5" x 0.4" Finish Gold Plated 72

73 PMI MODEL: DLVA-2G4G CD-1 DETECTOR LOG VIDEO AMPLIFIER (DLVA) PMI Model No. DLVA-2G4G CD-1is a detector log video amplifier (DLVA) that operates between the 2.0 to 4.0GHz frequency range. It has a dynamic range of 45dB, a log slop of 70mV/dB and a nominal video bandwidth of 14MHz. Furthermore, the DLVA has features that can convert any incoming signal ranging from 50ns to CW to a pulsed output of 600ns. In addition, the DLVA will not trigger an output with input pulse widths of 40ns or less. This state of the art design utilizes cutting edge technology which provides stunning performance and reliability in a compact package making it an optimum solution for high speed channelized receiver Frequency Range Input VSWR (50 Ohms) Input Power Handling Video Log Range 2.0 to 4.0GHz 1.92:1 (-10dB Max.) +20dBm Max. -30 to +15dBm Video Log Linearity 25 C Video Log Slope Video Frequency Flatness Pulse Width Range (50ns with little degradation in performance) (PW less than 40nS will not trigger an output) Video Output Impedance Video Rise Time Video Fall Time Recovery Time 70mV/dB ±5mV/dB ±1.5dB 80ns to CW 100 Ohms 35ns Max. 200ns Max. 1.0us Max. Settling Time Video Output Pulse Width Video Output Noise DC Supply 60ns Max. 600ns ±200ns 60mV p-p 50mA 80mA 100mA Size 3.035" x 0.91" x 0.35" 73

74 6.0 TO 18.0, 70dB, SUCCESSIVE DETECTION LOG VIDEO AMPLIFIER (SDLVA) PMI MODEL: SDLVA-6G18G-CD to 18.0 GHz Frequency Range 70dB Dynamic Range 10nS Rise Time 60nS Recovery Time MIL Temperature Range Low Loss Unconditionally Stable Hermetically Sealed 74

75 6.0 TO 18.0, 70dB, SUCCESSIVE DETECTION LOG VIDEO AMPLIFIER (SDLVA) PMI MODEL: SDLVA-6G18G-CD-1 PARAMETER FREQUENCY RANGE PULSE RANGE INPUT POWER FLATNESS LOG LINEARITY LOG RANGE SPECIFICATION 6.0 TO 18.0 GHz 30nS to CW +17 dbm CW Max ±2.0dB Max ±2.5dB Max -70 to +5 dbm LOG SLOPE 25mV/dB (±5%) VSWR RISE TIME RECOVERY TIME DC POWER SUPPLY 2.0:1 Max 10nS Max 60nS Max mA mA 75

76 Successive Detection Log Video Amplifier PMI MODEL: SDLVA-100M700M-70 Frequency Range Dynamic Range Log Linearity Log Linearity Minimum Log Voltage Maximum Log Voltage VSWR Input Tangential Sensitivity Limited IF Output Maximum RF Input Power Log Video Output Coupling Log Video Maximum Output Voltage Log Video Output Rise Time Log Video Output Fall Time Log Video Output Settling Time Log Video Output DC Offset Log Video Output Slope Log Video Output Variation with Frequency Log Video Output Variation with Temperature Log Video Propagation Delay 100 to 700MHz 55dB minimum, 60dB typical ±1.2dB typ., ±1.2dB (-55dBm to 0dBm) ±1.5dB typ., ±2.0dB (-60dBm to 0dBm) -55dBm (-60dBm typ.) 0dBm (+10dBm typ.) 2.0:1 max. (1.5:1 typ) -60dBm typical -10dBm minimum, -5dBm typical +10dBm DC 2.7 Volts 15ns typ., 25nsec max. 15ns typ., 30nsec max. 40ns maximum 0.1 Volts Nominal (Adjustable) 25mV/dB Nominal ±5mV/dB ±0.5mV/dB typ. (Over 80MHz RF Bandwidth) ±1mV/dB typ. 10ns Maximum, 7nS Typical Log Video Load 100 ohms ±10% DC Power (+V) +12 to mA -12 to mA DC Power (-V) Note: Do not supply +V without -V supplied as well as this may damage the unit Size 3.75 " x 1.50 " x 0.50" Finish Gold Plated 76

77 Successive Detection Log Video Amplifier PMI MODEL: SDLVA-315M362M-65-CD-1 Frequency Range Frequency Flatness TSS VSWR Power Input Log Slope Log Range Log Accuracy Log Accuracy 315 to 362MHz ±2.0 db max. -73dBm min. 1.5:1 max. +17dBm max. 50mV/dB (±1.5mV/dB) 100 Ohm Load -65 to 0dBm -65dBm and 0dBm) ±0.75dB (+50ºC) max. ±1.5dB (0ºC to +77ºC) max. Log Accuracy ±2.5dB (-33ºC to 0ºC) max. Pulse Range 100nsec to CW Rise Time 35nsec Fall Time 300nsec Recovery Time 500nsec Offset Adjust ±0.4V typ. Power Supply ±12V ±3% Quiescent Power Dissipation 2 Watts max. RF Connectors SMA(F) Finish Gold Plated Size 3.75" x 1.5" x 0.5" 77

78 6 to 18GHz, 70dB, Hermetically Sealed, Detector Log Video Amplifier (DLVA) PMI MODEL: DLVA-6G18G-50-HERM Frequency Range TSS VSWR Video Output Range Maximum Video Output 6.0 to 18.0GHz -72dB min. 2.0:1 max. 0 to 2.2VDC (50 Ohm Load) 2.4VDC Input Power +20dBm CW max. Logging Range -70 to 0dBm Logging Accuracy ±4.0dB max. Log Slope 25mV/dB (±10%) Log Slope Intercept Point At -70dBm RF Input, Output Voltage = 350mV Pulse Range 100nsec to CW Pulse Rise Time (10% to 90%) 50nsec max. Pulse Overshoot 1dB max. Pulse Fall Time (90% to 10%) 70nsec max. Recovery Time 70nsec max. Delay Time 15nsec max. Power Supply 265mA and 95mA Connectors SMA(F) Size 3.2 " x 2.05 " x 0.4" 78

79 80dB, Successive Detection Log Video Amplifier PMI MODEL: SDLVA-61F-80, opt Input Characteristics: Test Frequency: Signal Range: VSWR: Transfer Characteristics: Bandwidth: Transfer Function: Accuracy: Output Characteristics: Load Impedance Coupling Pulse Characteristics: Rise Time: Fall time: Stability Power Requirements: Supply: Ripple: Connectors: Input Signal: Output Signal: Power Connector: MHz ±250 KHz -80 dbm to 0 dbm 1.2:1 Maximum 6.0 to 8.6 MHz The Output shall conform to the following transfer function: E = 22.5 Pin Where Pin = Input Power in db Above -80 dbm E = Output Voltage in Millivolts The Output Voltage shall be E mv for any input in the signal range. 50 Ohms Output Shall be DC Coupled to Load 117 ns Maximum 491 ns Maximum to fall from 2V to 0.2V for an input pulse with an amplitude of 0 dbm. The unit shall be unconditionally stable (ie: Non-Oscillatory) under all operating conditions as well as for a source and/or load VSWR of 1.5:1 Maximum. The unit shall be unconditionally stable (ie: Non-Oscillatory) under all operating conditions. +15 VDC ± ma Per Channel -15 VDC ± ma Per Channel SMA Female SMA Female Cannon Type DEMM-9P or Equivalent with Screw Lock 79

80 80dB, Successive Detection Log Video Amplifier PMI MODEL: SDLVA-61F-80, opt LOG 25ºc 80

81 2 to 18GHz, 40dB, Detector Log Video Amplifier (DLVA) PMI MODEL: HADA-D2002 Frequency Range TSS VSWR (Input) Logging Range 2.0 to 18.0GHz -40dB Min. 3.0:1 Max. -40 to 0 dbm Log Accuracy ±1.50dB 25ºC Log Linearity Frequency Flatness Rise Time Fall Time Propagation Delay Maximum RF Input DC Offset Dimensions ±0.50dB Max. ±1.65dB Max. 30nS Max 100nS Max 60nS Max +23dBm +95mV 2.5 X 1.5 X 0.44, 150grms 81

82 2 to 18GHz, 40dB, Detector Log Video Amplifier (DLVA) PMI MODEL: HADA-D

83 5 - DTO s (DIGITALLY TUNED OSCILLATORS) DRO s (DIELECTRIC RESONANCE OSCILLATORS) PLO s (PHASE LOCKED OSCILLATORS) FREQUENCY SYNTHESIZERS & FREQUENCY DOUBLERS 83

84 PHASE LOCKED OSCILLATOR PMI MODEL No: PLO-1D6G-CD-2 PMI Model No. PLO-1D6G-CD-2 is a Phase Locked Oscillator with an output frequency of 1.6GHz. This model provides minimum output power of +14dBm with all spurs held to -60dBc and harmonics held to -20dBc. The unit has a VSWR of <1.5:1 for all phases and is supplied with SMA(F) connectors in a housing that measures 2.75" x 2.75" x 0.75". Output Frequency (fo) 1.6GHz Output Power +14dBm min, +18dBm max Reference (fi) 100 ±0.01MHz, 0 ±3dBm Spurious -60dBc min Harmonics -20dBc min Phase Noise 20 log(fo/fi) +6dB -100 dbc/hz 100KHz -120 dbc/hz 1 MHz Lock Alarm TTL "H" : Out of Lock TTL "L" : Lock Primary Power RF Input/Output +12 to 370mA -12 to 100mA SMA(F) Size 2.75" x 2.75" x 0.75" Finish Weight Painted Gray 280g (10 oz.) max 84

85 PHASE LOCKED OSCILLATOR PMI MODEL No: PLO-1D6G-CD-2 Harmonics Carrier Phase Noise Spurious 85

86 DIGITALLY TUNED OSCILLATORS (DTOs) 2.0 to 18.0 GHz Modulation BW DC to 9 MHz Phase Noise -60dBc/Hz Harmonics -20dBc Max. Spurious -55dBc Max. 86

87 DIGITALLY TUNED OSCILLATORS (DTOs) Digitally Tuned up to 16 bit 0.5 MHz/1.0 MHz Resolution Allows DC to 15 MHz Sine Wave Modulation 7 Frequency Bands Available including 2 to 18 GHz 87

88 DIGITALLY TUNED OSCILLATORS (DTOs) Model Number Frequency Range (GHz) Frequency Accuracy (±MHz) Frequency Drift (±MHz/ C) Frequency Settling (±MHz Max. within 1usec) RF Output Power (dbm Min.) Modulation Bandwidth (Min.) Phase Noise 100kHz Offset) Harmonics (dbc) AUM-50M100M-DTOK-3R5MBW < MHz Min AUM1001G-DTOK-3R5MBW < MHz Min DTO-0R5G2G-CD DC - 9MHz DTO-0R5G2D5G-CD DC to 9MHz DTO-2G6G-CD to +8 DC to 14MHz DTO-6G18G-CD DC to 10MHz DTO-218-CD DC to 9MHz

89 DIELECTRIC RESONANCE OSCILLATORS (DR0) PMI Model: PIA-10G-CD-1 FREQUENCY 10 GHz PHASE 360º Min. OUTPUT +19dBm Typ OUTPUT ADJUST 0 to 10dBm HARMONICS -50dBc Typ 89

90 DIELECTRIC RESONANCE OSCILLATORS (DR0) PMI Model: PIA-10G-CD-1 90

91 Phase Locked, Dielectric Resonator Oscillator (with Internal Reference) PMI Model: PIA-12D8G-CD-1 Frequency Output Power Output 12.8GHz VSWR 1.4:1 Internal Reference Frequency Stability Spurious Harmonics +13dBm minimum 100MHz ±3 ppm -80dBc -25dBc Phase Offset 1Hz 10Hz 100Hz 1kHz 10kHz 100kHz 1MHz DC Voltage Supply +15VDC DC Current 300mA maximum Phase Lock Alarm TTL Connectors SMA Female Finish Nickel Size 2.25" x 2.25" x 0.62" 91

92 Phase Locked, Dielectric Resonator Oscillator (with Internal Reference) PMI Model: PIA-12D8G-CD-1 <Power Output Harmonics > <Phase Noise> 92

93 PMI MODEL: PFS-618-CD-1 HIGH SPEED FREQUENCY SYNTHESIZER PMI Model No. PFS-618-CD-1 is a high speed frequency synthesizer that operates over the frequency range of 6.0 to 18.0GHz. This model covers the complete 6.0 to 18.0GHz frequency in 100kHz steps with an output power of +10dBm minimum. The unit is accurate to within ± 1MHz and settles within 1usec maximum. This model features low SSB Noise and a low spurious output of -55dBc maximum. Harmonics are kept below -30dBc. Frequency Modulation is offered and has a bandwidth of DC to 10MHz with ± 400MHz minimum at 100MHz / volt. The package is compact in size and measures only 6.48" x 6.23" x 1.6". Frequency Range Frequency Step Size, Nominal (LSB) Power Output Level Power Variation Frequency Accuracy Frequency Aging Settling Time to 1MHz Tuning Control Tuning Speed SSB 1kHz 100kHz 10MHz Offset Spurious Output Harmonics Sub-Harmonics Reference Frequency Modulation Modulation Bandwidth 6.0 to 18.0GHz 100kHz +10dBm Min. 5dB P-P (±2.5dB) Max. ±1MHz Max. ±2 PPM / Year 1usec Binary, TTL 17 Bits (Parallel) 1usec 6.0 to 18.0GHz Max. -78dBc / Hz -96dBc / Hz -100dBc / Hz -55dBc Max. -30dBc Max. -55dBc Max. Internal Reference DC to 10MHz Frequency Deviation ±400MHz Min., 100MHz / Volt Control Analog Sensitivity 1.1 : 1 Power Supply 2.5A Max. (1.4A measured) 0.6A Max. (0.1A measured) 4A Max (1.6A measured) 2A Max. (0.1A measured) Connectors Control 37 Pin Sub-D Male Power 9 Pin Sub-D Male RF Output SMA Female Modulation Input SMA Female Size 6.48" x 6.23" x 1.6" 93

94 PMI MODEL: PFS-618-CD-1 HIGH SPEED FREQUENCY SYNTHESIZER 94

95 PMI MODEL: PFS-618-CD-1 HIGH SPEED FREQUENCY SYNTHESIZER TYPICAL OBSERVED RESULTS: Typical Settling Time to 18GHz 10GHz) Phase Noise 9GHz) Full Frequency Range Carrier 14GHz) 8V P-P 10MHz Modulation 9GHz) 95

96 ACTIVE, FILTERED, FREQUENCY DOUBLER MODULE PMI MODEL: PFDM-3R66R R5DC-SFF Specifications: RF Input (GHz) 3.6 to 6.65 GHz RF Output (GHz) 3.6 to 13.3 GHz RF Input Power 0 to +4 dbm RF Output Power (MAX) +10dBm Attenuation Range (db) 10dB Harmonic Rejection (dbc) -25dBc Sub Harmonic / Multiple Harmonic Rejection (dbc) -65dBc Current +7.5vdc 600mA Output Switching Speed <20nSec. VSWR In/Out 2.0:1 Isolation between Outputs >35dB Operating Temp -10 to +65ºC Size 3.0 X 1.5 X

97 6 - FILTERS & DIPLEXERS 97

98 18 TO 40GHz, LOW LOSS DIPLEXER PMI MODEL No: 2SFB-8G26G-CD-SFF Insertion Loss (Passband) VSWR (Passband) Diplexer K Band 1dB Passband 2dB max 2.5:1 max 18.0GHz, Min, 25.0GHz max Diplexer Ka Band 1dB Passband Crossover Band Crossover Excess Attenuation Stopband Attenuation K Band (Stopband) Ka Band (Stopband) Connectors Input/Output 28.0GHz min, 40.0GHz max 25.0GHz min, 28GHz max 5dB typ 60dB 32.0GHz GHz DC GHz 2.92mm(F) Size 0.80" x 0.60" x 0.38" Weight Finish 0.5oz typ Painted Blue 98

99 18 TO 40GHz, LOW LOSS DIPLEXER PMI MODEL No: 2SFB-8G26G-CD-SFF K-BAND: (10dB Scale) INSERTION LOSS, VSWR, & REJECTION CROSSOVER OF K & Ka BANDS (10dB Scale) Ka-BAND: (10dB Scale) INSERTION LOSS, VSWR, & REJECTION 99

100 11.5 to 16.5GHz Diplexer PMI Model No: 11DP-11R5/16R5-CD-SFF-1 Center Frequencies, Fo Filter #1: 11.5GHz Filter #2: 16.5GHz Passband Frequencies Filter #1: to 12.25GHz Filter #2: to 17.25GHz Passband Insertion Loss 3dB max. Passband VSWR 1.5:1 max. Rejections Filter #1: 10.25GHz & 13.75GHz Filter #2: 17.75GHz & 14.25GHz Size 3.5"L x 1.4"W x 0.5"H Connectors In / Out SMA(F) - Field Removable Finish No Paint - Silver Plated 100

101 11.5 to 16.5GHz Diplexer PMI Model No: 11DP-11R5/16R5-CD-SFF-1 BAND PASS FILTER #1 NARROW-BAND PLOT BAND PASS FILTER #2 NARROW-BAND PLOT 101

102 PMI MODEL: BPF CD-TNCMF-LK 6 WATT BANDPASS FILTER, 2dB LOSS REJECTION Center Frequency, Fo 1dB Bandwidth Ultimate Stopband Rejection Insertion Loss Stopband Cutoff -Lower -Upper RF Input Power Connectors Finish 1370MHz 50MHz 60dBc minimum Less than 2dB 800 to 1200MHz 1312MHz or higher at 30dB 1434MHz or lower at 30dB 6 Watts at 10% Duty Cycle TNC - Male (Input) & TNC - Female (Output) Painted Gray Size 2.25" x 1.0" x 0.75" 102

103 PMI MODEL: HPF NFF-50W 50 WATT, HIGH PASS FILTER Passband 130 to 550MHz -1dB Cut-Off Frequency 130MHz Passband Insertion Loss 1.0dB INSERTION LOSS & RETURN LOSS Passband VSWR 2.0:1 Rejection 90MHz Operating Input Power 50 Watts CW max. Impedance Size Connectors In/Out 50 Ohms 6.0"L x 2.0"W x 1.5"H N(F) 103

104 PMI MODEL: 4BP A-PP 160 MHz, LC BANDPASS FILTER Center Frequency 160MHz, +/-0.23% 3dB Bandwidth 5MHz, +/-5% VSWR in the Pass Band 1.5:1 max Pass Band Insertion Loss 10dB nom Rejection Connectors In/Out 4 Section Response PC Pins Size 1.2" x 0.31" x 0.31" 104

105 PMI MODEL: BP13G-10G-CD-SFF 8 TO 18 GHz, SUSPENDED SUBSTRATED BANDPASS FILTER Passband Frequency Passband Insertion Loss 8.0 to 18.0GHz 1.5dB typical, 2.5dB max. INSERTION LOSS / RETURN LOSS / GROUP DELAY & PHASE LINEARITY Passband VSWR 2.0:1 max. Rejection 70dB typ. at DC to 6GHz 60dB typ. at 20 to 23GHz Connectors SMA - Female (Field Removable) Size Finish 1.94"L x 0.76"W x 0.5"H Gold Plated 105

106 18 to 26.5GHz, HIGH PASS FILTER PMI MODEL: HPF18G-DC15G Passband 18.0 to 26.5GHz Insertion Loss (Passband) 1.5dB max VSWR (Passband) 2.0:1 max Rejection DC GHz 60dB Connectors 2.92mm(F) INSERTION LOSS, VSWR & REJECTION Size 0.64" x 0.58" x 0.38" Weight Finish 0.5oz typ Painted Blue 106

107 DC to 26.5GHz, LOW PASS FILTER PMI MODEL: LPF26R5-28R5G40G Passband DC to 26.5GHz Insertion Loss (Passband) 1.5dB max VSWR (Passband) 2.1:1 max Rejection 28.5 to 40GHz Ripple 25dB Typ. ±0.75dB max INSERTION LOSS, VSWR & REJECTION Connectors 2.92mm(F) Size 0.45 X 0.38 X 0.50 Weight 0.5oz typ Finish Painted Blue 107

108 6 to 18GHz RF FILTER/DETECTOR PMI Model No: RFFD PMI MODEL RFFD IS A 6 TO 18GHz LOW PASS FILTER COMBINED WITH A SCHOTTKY BIASED DETECTOR INCLUDING A REVERSE VOLTAGE PROTECTION DIODE, A DUPLICATE DETECTOR AND PROTECTION DIODE IS INCLUDED FOR DC OFFSET VOLTAGE COMPENSATION. Frequency Range Return Loss Maximum Input Power Filter Rejection Voltage Sensitivity Barrier Potential Operating Dynamic Range 6 to 18GHz -10dB 7dBm Operational 20dBm Survival 23dB min. (20 to 26GHz) 80 to 140mV 225 to 270mV with 100uA bias to +25 Deg. C -23 to +7dBm Frequency Flatness ±0.8dB with 1dB to 2dB typical slope Diode Voltage Protection Tracking Detector-Balance 1.0V max. at 30mA ±20mV max. over operating temperature Connectors: RF Input: Filed Replaceable Video Output : Fiel d Replaceable DC Connections SMA(M) SMA(F) Feed-thru Solder Pins Size 1.60" x 1.59" x 0.6" 108

109 7 - FORM, FIT & FUNCTION PRODUCTS 109

110 FORM, FIT & FUNCTION PRODUCTS If you can not find the required components due to parts obsolescence please contact us. We offer form, fit, and function replacement parts for any system. If a Source Control Drawing (SCD) is available we can offer a complete solution to meet all of the given electrical, mechanical and environmental specifications. Specializing in aftermarket technology manufacturing and support for discontinued RF components, electronic circuits, digital circuits and Integrated circuits, PMI has the technical expertise to manufacture, supply and support these requirements. We are dedicated to assuring our customer base that older discontinued products will continue to be available. IF & RF LOG AMPLIFIERS VARIABLE GAIN AMPLIFIERS SUCCESSIVE DETECTION LOG VIDEO AMPLIFIERS (SDLVA s) BI-PHASE MODULATORS PHASE SHIFTERS I & Q VECTOR MODULATORS FREQUENCY DISCRIMINATORS FILTERS DIPLEXERS & MULTIPLEXERS SWITCH FILTER BANKS SUPERCOMPONENTS, SUBSYSTEMS AND SYSTEMS SMT VOLTAGE REGULATORS DIGITAL CIRCUITS TO-8, OP-AMS PLO's, DRO's, and DTO's 110

111 8 - IFMs & FREQUENCY DISCRIMINATORS 111

112 PMI MODEL: FD-30M-6M FREQUENCY DISCRIMINATOR Specifications: Frequency Range VSWR Input 12 to 18 GHz 2.0:1 Maximum 1.5:1 Typical Operating Input Power +10 dbm Nominal, ±0.1 dbm Video Impedance Video Output Rise Time Video Output Slope Frequency Discriminator Accuracy RF Input Power, Survival Power Plus Power Minus 100 Ohms Nominal 20 ns 50 mv/ghz ±200 MHz +15 dbm ma ma Size 2.00" x 1.80" x 0.50" Weight <4 Ounces 112

113 PMI MODEL: FD OPT to 18GHz, FREQUENCY DISCRIMINATOR VIDEO RISE & FALL 113

114 PMI MODEL: FD-30M-6M FREQUENCY DISCRIMINATOR Center Frequency Peak to Peak Bandwidth Linear Bandwidth Sensitivity 30MHz 10MHz min. 6MHz min. 1000mV/MHz ± 5% Into 50 Ohms Linearity ± 5% Input VSWR Input Dynamic Range Rise Time Pulse Width Pulse Repetition Positive DC Supply Negative DC Supply 2.0:1 max. -10 to 0dBm 120nsec max. 1usec min. 1kHz mA max mA max. Size 4.625" x 1.50" x 0.47" Finish Painted Gray 114

115 PMI MODEL: FD-30M-6M FREQUENCY DISCRIMINATOR Video 35MHz, with RF Pulse Typical Input -10dBm Input Power Rise 35MHz 115

116 PMI MODEL: FD Option CHANNEL, FREQUENCY DISCRIMINATOR SPECIFICATIONS: FREQUENCY RANGE: OUTPUT CHANNELS: 1.0 to 18.0 GHz Ch1 1.0 to 2.0 GHz Ch2 2.0 to 4.2 GHz Ch3 4.2 to 6.1 GHz Ch4 6.1 to 8.7 GHz Ch5 8.7 to 12.5 GHz Ch to 18.0 GHz INPUT VSWR: 2.0:1 OUTPUT VOLTAGE: VIDEO OUTPUT RISE/FALL TIME: VIDEO IMPEDANCE: OPERATING INPUT POWER: ACCURACY: POWER SUPPLY: WEIGHT: Proportional to Input Frequencies 20Ns Maximum 100 Ohms +10dBm ±300 MHz Typical 875 ma Maximum 150 ma Maximum 6 LBs SIZE: 8.5 x 5.0 x

117 PMI MODEL: FD Option CHANNEL, FREQUENCY DISCRIMINATOR 117

118 9 - INTEGRATED MIC/MMIC PRODUCTS 118

119 AMPLIFIED, RF LASER CONTROL MODULE PMI MODEL No: LCM-7R7G8R2G-CD-1 Frequency Range Gain J1 to J2 J2 Output 1dB Compression Conversion Gain 7.7 to 8.2GHz 16dB, ±2dB max (Attenuation = 0dB) 28dBm typ 0dB, ±3dB max (J1 = 10dBm, J4 = -10dBm) Tap Out Insertion Loss 16dB, ±2dB typ (J1 to J5) Input Power J1 20dBm max Input Power J4 14dB max VSWR J1, J2, J3, J4, J5 2.2:1 max Power Supply +1000mA max -200mA max Size 2.5" x 1.75" x 0.4" Finish Gold Plated Low Noise Amplifier 1, 2, 3 Gain Saturated Output Power Noise Figure Reverse Isolation Phase Shifter Phase Shift Range Control Range Non-Linear Slope Ratio Switching Speed Attenuator Attenuation Range Control Range Non-Linear Slope Ratio Switching Speed Filter 1, 2, 3, 4, 5 Pass Band Stop Band, Lower Stop Band, Upper Low Pass Active Filter Pass Band Stop Band 14dB typ 16dBm typ 2.5dB typ 40dB typ 0 to 360 min 0 to 10 Volts 4:1 typ 200nsec max 0 to 20dB min 0 to 10 Volts 8:1 typ 1.0usec max 7.7 to 8.2GHz, (2dB) typ DC to 6.8GHz (20dB) typ 10.3 to 18.0GHz, (20dB) typ DC to 10KHz min 10KHz (Roll Off 6dB per Octave) typ 119

120 AMPLIFIED, RF LASER CONTROL MODULE PMI MODEL No: LCM-7R7G8R2G-CD-1 120

121 MONOPULSE COMPARATOR MPC-20R2G21R2G-CD-LNF Frequency 20.2 to 21.2 GHz Lossless from Input to Output Designed for 100K Noise Temperature Phase Tracking all 8 Inputs 121

122 MONOPULSE COMPARATOR MPC-20R2G21R2G-CD-LNF Section 1 8 Antenna Inputs Phase Matched LNAs Hybrid Tee Ringline Couplers Phase Matched Outputs Section 2 Hybrid 90 Power Divider Branchline Coupler SPDT Absorptive Switch Solid State 122

123 LEVEL, SCAN & PULSE MODULATOR PMI MODEL: LSP-0518-SK SCAN MODULATION: Linear transfer function for control voltage of attenuation as expressed in db s. This is in reality an exponential transfer function. Vout = A x 10 ^ (Vcontrol / B) A and B are constants A Typical Transfer Function Specification would be: 10dB per Volt. LEVEL SETTING: In the LSP module the level setting function is similar to the scan modulation in that a control voltage sets the db s of attenuation to vary the output level. PULSE MODULATION: This is an on and off function, switching the RF on and off to generate waveforms of a desired shape or characteristic. ATTENUATION: Attenuation is the incremental reduction of signal strength through controlled adjustments of ever increasing resistance within the RF circuit. These controls can be either through digital or analog inputs. Attenuation is expressed in db s. The Level set and Scan modulation functions are in reality attenuation controls. 123

124 LEVEL, SCAN & PULSE MODULATOR PMI MODEL: LSP-0518-SK 124

125 MODULATOR AMPLIFIER PMI MODEL: PMA-218-LSP PMI Model Number PMA-218-LSPis an Analog Level, Scan and Pulse Modulation Module that is capable of exponential (linear in db) Modulation, for rugged and high reliability applications using digital process techniques, that works from 2.0 to 18.0 GHz. Frequency Range Output P1 db IP3 RF Input Power Harmonics at P1 db Spurious Outputs VSWR (RF Input) VSWR (RF Output) Level Set (Power Attenuation) Scan Modulation (Attenuation) Combined Attenuation Scan and Level Bandwidth Scan Pulse Response (Settling) Scan Pulse Response (Rise/Fall) Digital Processing Jitter System Frequency Flatness Attenuation Frequency Flatness Attenuation Linearity Pulse Modulation Depth RF Pulse Width Range RF Pulse (Rise Time 10-90%) RF Pulse (Fall Time 90-10%) RF Pulse Repetition Rate RF Pulse Distortion Pulse / CW Differential Pulse Width Fidelity Sensitivity Bias Voltages / Currents 0.5 to 18.0 GHz +12 dbm Minimum +22 dbm Minimum +14 dbm Maximum +12 dbm Operational dbc Minimum -60 dbc Minimum 2.2:1 Maximum 2.2:1 Maximum 70 db Range 70 db Range 100 db Minimum 10 khz 50 us Maximum 15 us Maximum 10 us Maximum ±2 db 0-40 db (±2 db) db (±3 db) ±1.5 db 60 db Minimum 50 ns to CW 9 ns Maximum 9 ns Maximum 10 MHz Maximum 0.3 db Maximum 0.4 db Maximum ±10 ns Maximum 6 db/volt Amps Maximum Amps Maximum Size 4.00" x 3.30" x 0.70" 125

126 MODULATOR AMPLIFIER PMI MODEL: PMA-218-LSP 126

127 PMI MODEL: DGM-18G40G-292FF-DS QUAD-PHASE & AMPLITUDE MATCHED MILLIMETERWAVE DIPLEXER-GAIN MODULE PMI Model No. DGM-18G40G-292FF-DS is a Quad Phase & Amplitude Matched mmw (Millimeter Wave) Diplexer-Gain module designed to operate over the 18.0 to 40GHz frequency range with a switched output and an integrated power divider feeding the four antenna inputs via a 20dB coupler for ease of system set up. The band select function not only switches bands, but also allows the amplified bands not in use to be turned off to reduce power consumption. This model is also designed to have better than 60dB harmonic suppression. Channel to Channel Performance 127

128 PMI MODEL: DGM-18G40G-292FF-DS QUAD-PHASE & AMPLITUDE MATCHED MILLIMETERWAVE DIPLEXER-GAIN MODULE 128

129 PMI MODEL: DGM-18G40G-292FF-DS QUAD-PHASE & AMPLITUDE MATCHED MILLIMETERWAVE DIPLEXER-GAIN MODULE FREQUENCY RANGE GAIN AMPLITUDE RIPPLE INPUT P1dB INPUT IP3 CHANNEL TO CHANNEL ISOLATION NOISE FIGURE PHASE MATCHING PHASE TRACKING mmw / µw LIMITER LIMITER 1dB RECOVERY TIME SPURIOUS PRODUCTS DIPLEXER K BAND, 1dB PASSBAND DIPLEXER Ka BAND, 1dB PASSBAND CROSSOVER BAND CROSSOVER EXCESS ATTENUATION STOPBAND ATTENUATION K BAND STOPBAND Ka BAND STOPBAND COMM BAND ATTENUATION COMM BAND COMM INTERFERENCE IMMUNITY COMM INTERFERENCE IMMUNITY VSWR IN PASSBANDS HARMONICS FOR -20dBm BAND SWITCHING TIME, REQUIRED 18.0 to 40.0 GHz 3dB Min., 7dB Max. ±0.5dB over every 500MHz BW -20dBm Min. -10dBm, +5dBm Goal 50dB Typ. 15dB Typ. 40º RMS Channels 2,3,4 to REF. Channel 1, over operating temperature 0.25º/ºC Port to Port Typ. 30dBm, CW or Pulsed, 2.0 to 40.0 GHz Without Damage, All Inputs. 250nS -73dBm 18.0 GHz Min., 25.0GHz Max 28.0GHz Min., 40.0 GHz Max 25.0GHz Min., 28.0 GHz Max. 4dB Attenuation Above K or Ka Passband IL 60dB 900MHz to 15.0GHz, 32.0 GHz to 46.0GHz 900MHz to 22.0GHz 60dB 900 MHz to 2.5 GHz 36dBm CW, 900 MHz to 2.5 GHz w/out Limiter or Amplifier Saturation 53dBm Pulsed RF, 900 MHz to 2.5GHz w/out Limiter or Amplifier Saturation 2.0:1 Typ. -80dBm, 15 to 40GHz 10mS BAND SWITCHING TIME, GOAL 1µS BAND SWITCH PROTECTIVE CIRCUITRY POWER SUPPLY PROTECTION CIRCUITRY ON BOTH ±6.0 VDC SUPPLIES POWER SUPPLY VOLTAGE POWER CONSUMPTION REQUIRED MASS CONNECTORS CONTROL CONNECTORS SIZE ±15 VDC ±15 VDC ±6 VDC 5 W Goal 100 W Goal 2.92mm(F) Outputs and Power Divider Input 2.92 mm(m) Inputs. MDM-9PSP (9 Pin Micro-D with Mating Connector 3.0 X 8.0 X

130 PMI MODEL: PFEM-9D4G-CD-1 MULTI-FUNCTION MODULE PMI Model No. PFEM-9D4G-CD-1 is a multi-function module that provides amplification, switching and filtering within the frequency band of 9410MHz. This module provides two input channels and is switchable to a common output. This model is designed to offer multiple gain level selection, high channel to channel isolation and fast switching speeds. 130

131 PMI MODEL: PFEM-9D4G-CD-1 MULTI-FUNCTION MODULE SPECIFICATIONS TX (State 1) RX Low Gain (State 2) RX High Gain (State 3) Max Input Power at J1 0dBm 14dBm 14dBm Frequency 9410MHz +/- 30MHz 9410MHz +/- 30MHz 9410MHz +/- 30MHz Gain 0 to -5dBm 11 to 15dBm 30 to 35dBm Gain Flatness <0.1dBm <0.1dBm <0.1dBm Noise Figure N/A 2dB Nominal, 2.5dB Max 2dB Nominal, 2.5dB Max VSWR 1.5:1 typ. 1.5:1 typ. 1.5:1 typ. OP3 (Output) > 18dBm >18dBm >18dBm OP2 (Output) >8dBm >8dBm >8dBm Port to Port J1-J3 Isolation >85dB N/A N/A Max Output Power + 23dBm Output Signal Distortion Video Switching Transients Stability Max Out-Of-Band Gain Switching Time Switching Control BIAS V/I No apparent droop or distortion with a pulse width of 500 to 1000nsec, at 500 to 2000 PPS < -120dBm above 1.7GHz Unconditionally stable when terminated at J1, J2 and J3 with short circuit at all phases Below In-Band Gain for f > 6.5GHz -20 db Below In-Band Gain < 6.5GHz 50ns: TX to RX 50ns: RX Low Gain to RX High Gain 3.3V to 5V, TTL Compatible +12VDC/ 125mA typ. Size 2.89' x 1.62" x 0.63 Finish Painted Gray 131

132 PMI MODEL: PEC-18-2R35G-1R75-9-SFF-HS-LM INTEGRATED AMPLIFIER, SWITCH, LIMITER & FILTER MODULE PARAMETERS SPECIFICATIONS CENTER FREQUENCY 1dB Bandwidth 30 dbc Rejection Gain (typ) Noise Figure Isolation VSWR RF Input Power RF Output Power Switching Speed (On/Off) EMI Shielding Differential Control DC Power Supply 2.35 GHz 150 MHz 2100 and 2600 MHz 18dB 1.8dB Typ 2.0 db Max 40dB Min 2.0:1 Max +30 dbm Max +2 dbm Max 100nS Max 60 1 Foot Min A>B = ON B>A = OFF +9 VDC 132

133 PMI MODEL PIA-BTFL-GPO-2CH INTEGRTED BIAS-T, BAND PASS FILTER WITH LIMITED OUTPUT PARAMETERS SPECIFICATIONS PASSBAND LOWER LIMIT: 2.0 GHz Typ PASSBAND UPPER LIMITER 19.0 GHz Min -3dB Cut off 1.85dB Typ PASSBAND INSERTION LOSS 1.85 db Typ, 2.5dB Max REJECTION -15 dbm 1.7 GHz -20dBm DC to 1.5 GHz PASSBAND VSWR 2.0:1 Max Bias-T Suspended Substrate Bandpass Filter Limiter BIAS Rise/Fall 90% to 10% / 10% to 90% LIMITING THRESHOLD 50nS Max +8dBm Min. PULSE RECOVERY TIME 50nS Max (to within 1dB of IL) 133

134 PMI MODEL: PSD-2G6G-CD-1 & PSD-6G18G-CD-2 HIGH POWER SWITCH/LIMITER ASSEMBLY PMI Model No. PSD-2G6G-CD-2 and the PSD- 6G18G-CD-2 are High Power, Switch Box Assemblies that provides protection to front-end receivers when in the presence of high power signals. This is accomplished by sensing the input signal level and then switching the input signal into 50 ohms terminations when a set threshold level is exceeded. This assembly operates from 2.0 to 6.0GHz and 6.0 to 18.0 GHz respectively and can handle input power levels up to 10 Watts CW. The unit is supplied with an external 0 to 69dB step attenuator that can be used to adjust the signal levels feeding the internal threshold detector and thereby setting the trigger level of when the unit passes the input RF signal to the output of the switch assembly or when the signal is switched into the internal 50 ohms terminations. The switching speed is 50ns maximum. This unit operates on 110VDC, 50/60Hz and is supplied in a housing that measures 6.0 x 8.0 x 2.5. This unit is ruggedized and designed for harsh environments and is EMI shielded. 134

135 PMI MODEL: PSD-2G6G-CD-2 HIGH POWER SWITCH/LIMITER ASSEMBLY Final Assembly: Frequency Response 2.0 to 6.0GHz Power 110VAC Only, 50.60GHz Size 6.0 X 8.0 X 2.5 Finish Painted Gray Weight 20 lbs typ. Pin Diode Switch: Power Handling >= 10W Frequency Response 2.0 to 6.0GHz Switching Speed < 50ns Threshold Detector: Frequency Repsonse 2.0 to 6.0GHz Switching Speed < 50ns Output Type TTL (Compatible with Pin Switch) Sensitivity < -40dBm Max Power (No Damage) Coupler: Power Handling Frequency Response Coupling Factor 50 Ohm LOAD: Power Handling Frequency Response Attenuator: Power Handling Frequency Response Attenuation 10 dbm >= 10W 2.0 to 6.0GHz 20 db >= 10W 2.0 to 6.0GHz > 2W 2.0 to 6.0GHz 0-69 By (1) Front Panel Knob or Thumb Wheel 135

136 PMI MODEL: PSD-6G18G-CD-2 HIGH POWER SWITCH/LIMITER ASSEMBLY Final Assembly: Frequency Response 6.0 to 18.0GHz Power 110VAC Only, 50.60GHz Size 6.0 X 8.0 X 2.5 Finish Painted Gray Weight 20 lbs typ. Pin Diode Switch: Power Handling >= 10W Frequency Response 6.0 to 18.0GHz Switching Speed < 50ns Threshold Detector: Frequency Repsonse 6.0 to 18.0GHz Switching Speed < 50ns Output Type TTL (Compatible with Pin Switch) Sensitivity < -40dBm Max Power (No Damage) Coupler: Power Handling Frequency Response Coupling Factor 50 Ohm LOAD: Power Handling Frequency Response Attenuator: Power Handling Frequency Response Attenuation 10 dbm >= 10W 6.0 to 18.0GHz 20 db >= 10W 6.0 to 18.0GHz > 2W 6.0 to 18.0GHz 0-69 By (1) Front Panel Knob or Thumb Wheel 136

137 PMI MODEL: PMOD-PWR-1030M-ATN-SFF POWER DETECTOR MODULE Sigma Input Signal Frequency Forward Input Power (J1) Reverse Input Power (J2) Omega Input Signal Frequency Forward Input Power (J3) Reverse Input Power (J4) Synchronize ER/Sync (J11) Specification 1030 MHz ±0.0 MHz dbm ±5 db (+50dBm No Damage) dbm ±1 db (+35dBm No Damage) 1030 MHz ±0.01 MHz dbm ±2 db (+50dBm No Damage) dbm ±2.5 db (+35dBm No Damage) PMI Model No. PMOD-PWR-1030M-ATN-SFF is a power detector module. The operating frequency is 1030MHz +/-0.01MHz. Two pairs of forward and reverse signals are input allowing for a 12 bit linear digital output proportional to the input power. A GUI is provided to interface through Ethernet and allow MCU programming, unit calibration and setting of the variable attenuators. Pulsewidth Amplitude Impedance GUI 38 usec 0 to 5 VDC 75 Ohms - Interfaces with unit through ethernet connection - Allows setting of variable attenuators - Allows calibration of power detectors - Allows programming calibration table to microcontroller without need for additional hardware Test Video Specification ER/MNTRVID (J5) Digital Control Lines (Other than ER/Sync) DC Power 0 to 5 VDC Amplitude TTL Differential Pairs +5 VDC +/-5% +15 VDC +/-5% -15 VDC +/-5% Connectors J1, J2, J3, J4, J5, J11 SMA(F) J6 15 Pin Sub-Miniature D Male J8, J9 37 Pin Sub-Miniature D Male J7 Molex or Equivalent J10 Ethernet/ RJ45 Finish Painted Blue 137

138 PMI MODEL: PMOD-PWR-1030M-ATN-SFF POWER DETECTOR MODULE FRONT REAR FUNCTIONAL BLOCK DIAGRAM 138

139 10 - I & Q VECTOR MODULATORS 139

140 PMI MODEL: PIQ-85M18G-360/20-CD-2 I/Q VECTOR MODULATOR PMI Model No. PIQ-85M18G CD-2 is a Vector Modulator covering the frequency range of 85MHz to 18GHz. This unit provides an attenuator resolution of 0.1dB and a phase shift resolution of 0.8 degrees. The attenuation is phase invariant and the phase is amplitude invariant making it ideal for nulling unwanted signals. The unit can be specifically calibrated for any number of 100MHz bands within the full operating frequency range of 85MHz to 18GHz Frequency Range Phase Range Attenuation Dynamic Range Attenuation Resolution Insertion Loss Amplitude Variation Amplitude Variation, Narrow Band Phase Variation, Narrow Band Phase Resolution Return Loss (Input / Output) RF Input Power, Operating 0.85 to 18.0GHz 360 Nominal 20dB min. 0.1dB max. -3dB ± 4dB ±4dB across frequency range ±0.5dB across any 50MHz (100MHz to 500MHz) ±0.5dB across any 100MHz (50MHz to 18GHz) ±2 over any 50MHz (100MHz to 500MHz) ±2 over any 100MHz (500MHz to 18GHz) 0.8 max. 10dB min. 0dBm to +10dBm max. RF Input Power (CW) Damage Threshold Control Type - Frequency Setting - Phase Shift Setting - Attenuator Setting Band Switching +30dBm CW max. 8-BIt TTL for 100 MHz Bands 9-Bit TTL 8-Bit TTL Switching Speed 3usec typ. Power Supplies ±15V and +5V Gain For Output Amplifier Noise Figure For Output Amplifier OIP3 For Output Amplifier OP1dB For Output Amplifier Integrated Input / Output Switch (Nominal) 28dB Nominal 4dB Typical 27.5dBm Typical 16dBm Typical Size 6.0" x 3.0" x 1.0" RF Connectors SMA (F) Digital / Power Connector Finish MDM-37PH003P or Equivalent Mating Connector Provided Painted Gray 140

141 PMI MODEL: PIQ-85M18G-360/20-CD-2 I/Q VECTOR MODULATOR SWITCHING SPEED FULL PULSE 141

142 PMI MODEL: PIQ-0R5G2G CD-1 I/Q VECTOR MODULATOR PMI Model No. PIQ-0R5G2G CD-1 is a 0.5 to 2.0GHz, High Performance I/Q Vector Modulator with 2 x 12 bit monotonic TTL compatible channels (I and Q). This model offers a full 360 degrees of phase shift with a minimum of 20dB of amplitude control. Frequency Range Dynamic Range RF Input Power Insertion Loss VSWR Attenuation vs Frequency Phase vs Frequency Control Logic Control Slopes Switching Speed Temperature Coefficient 0.5 to 2.0GHz 20dB & 360 Degrees +5dM CW, 1.0 Watt max 11.0dB max 1.6:1 max (50 ohm system) ±1,5dB typ. ±10.0 degrees typ 2x12 BITs (I & Q), TTL Compatible Linear 500 nsec max ±0.035 db/ºc & ±0.17 Deg/ºC Power Supply ±12V to 100mA max RF Connectors SMA Female Input and Output Power/ Logic Connectors DC-37P, Sub Miniature D Multi-Pin Size 5.0" x 5.0" x 1.0" 142

143 PMI MODEL: PIQ-0R5G2G CD-1 I/Q VECTOR MODULATOR Insertion Loss, VSWR & 0º Polar +60ºC Polar +25ºC Polar -10ºC PHASE vs. 25ºC ATTENUATION vs. 25ºC 143

144 PMI MODEL: PIQ-2G18G CD-1 I/Q VECTOR MODULATOR PMI Model No. PIQ-2G18G CD-1 is a 2.0 to 18.0GHz, high performance I/Q Vector Modulator with 2 x 12 bit monotonic TTL compatible channels (I and Q). This model offers a full 360 degrees of phase shift with a minimum of 16dB of amplitude control. Frequency Range Dynamic Range RF Input Power Insertion Loss VSWR 2.0 to 18.0GHz 16dB & 360 degrees +10dBm CW, 1.0 Watt max 16.0dB max 2.2:1 max (50 OHM System) Attenuation vs Frequency Phase vs Frequency Control Logic Control Slopes Switching Speed Temperature Coefficient ±3.5dB typ ±20.0 degrees typ 2x12 BITs (I & Q), TTL Compatible Linear 500 nsec max ±0.035 db/ºc & ±0.17 Deg/ºC Power Supply ±12V to 100mA max RF Connectors SMA Female Input and Output Power/ Logic Connectors DC-37P, Sub Miniature D Multi-Pin Size 4.25" x 3.5" x 1.0" 144

145 PMI MODEL: PIQ-2G18G CD-1 I/Q VECTOR MODULATOR Polar 25ºC Phase 25ºC Insertion Loss, VSWR & 0º@ 25ºC Attenuation 25ºC 145

146 11 - LIMITERS & DETECTORS 146

147 HIGH SPEED, 1 WATT LIMITER, 0.5 to 18.0GHz LM W-SHS-1 Frequency 0.5GHz to 18.0GHz Insertion -20dBm Input 2.0 db max., 1.5 db typ. VSWR Input 1.5:1 Input Power: Pulse Width: 1 Watt CW 1 Watt CW 100 Watts Peak, 1uS Pulse 0.1% Duty Cycle, Derated to 125C 1usec +14dBm Max. +10dBm Typ. Duty Cycle: 0.1% 1 watt CW Input +14dBm max. Speed 10nS Size 0.5" x 0.5" x 0.22" 147

148 Ultra-High Speed, 1 Watt, Limiter LM-18G40G-18-1W-292FF Frequency Range 18.0GHz to 40.0GHz Insertion Loss 4.0 db Max. Input Power 1 Watt CW Max. Leakage Power +18dBm Max. 1dB Recovery Time 10nsec Max. VSWR 2.1:1 Connectors 2.92mm (F) Removable (K-Type Equivalent) Size 0.5" X 0.5" X 0.22" Weight 1.5 OZ. Typ. 148

149 5 WATT, COAXIAL LIMITER PMI MODEL: LM-30M3G-5W-SMF PARAMETERS SPECIFICATIONS FREQUENCY RANGE 30 MHz to 3.0 GHz INSERTION LOSS 1.2dB Max PEAK RF INPUT POWER 5 WATTS 25C LEAKAGE POWER +16dBm Max RECOVERY TIME 1µS Max INPUT VSWR 1.5:1 Max 149

150 5 WATT LIMITER PMI Model: LM-2G8G-13-5W-SFF PARAMETERS SPECIFICATION FREQUENCY 2.0 to 18.0 GHz INPUT POWER 5 Watts CW Max LEAKAGE 13 dbm Max RECOVERY TIME 40nS Max INSERTION -20 dbm Input Power -20 dbm Input Power 1 db Typ 2.0:1 Max 150

151 5 WATT LIMITER PMI Model: LM-2G8G-13-5W-SFF RECOVERY TIME 151

152 20 WATT, 35.5GHz, LIMITER PMI MODEL: LM-35D5G-14-20W-292FF FREQUENCY 35.5GHz INSERTION LOSS 2.0dB PEAK POWER 43dBm PULSE WIDTH 440 to 670 nsec PRF 600 to 900 KHz DUTY CYCLE 40% LEAKAGE POWER +14dBm Typ 1dB RECOVERY TIME 100nSec 152

153 20 Watt, Surface Mount Limiter LM-18G40G-SMT-1 Frequency Range Insertion Loss Peak Input Power 18GHz to 40GHz 4.0dB Maximum 20 Watts, 440 to 670nsec Pulse Width, PRF 600 to 900kHz, 40% Duty Cycle Leakage Power +14dBm Typical 1dB Recovery Time 250nsec Maximum VSWR 2.0:1 Size of SMT / Drop-In Carrier 0.198" X 0.270" X 0.016" 153

154 30 WATT, LIMITER PMI MODEL: LM-6D7G7D9G-30W-SFF Frequency 6.7GHz to 7.9GHz Insertion -20dBm Input 1.1dB max. Input -20dBm Input 1.5:1 max. Impedance 50 Ohms Input Power 30 Watts CW max. Maximum Flat Leakage 18dBm max at Input Power of 30 Watts CW Recovery Time 10usec max Size 1.0" x 0.65" x 0.38" Finish Gold Plated 154

155 HIGH SENSITIVITY DETECTOR PMI MODEL: DD PF-3-P-M Frequency Range Voltage Sensitivity TSS Frequency Flatness VSWR Rise Time Video Capacitance Output Voltage Maximum Input Power Connectors 2 to 18 GHz 500 mv / mw typical 2MHz Video Bandwidth (With 2dB Noise Figure Amplifier) ±1.0dB 3.5:1 Maximum (Measured at Pin = -23dBm) 10nsec typical 5.6pF typical Positive (Negative Available Upon Request) +20dBm CW Input: SMA Male Output: SMA Female Size 0.5" x 0.5" x 0.22" Finish Mil-SPEC Epoxy Paint, Gray Rise Time 4.63nS 10nS / Div. & 100nS PW Detector Flatness vs. Frequency -20dBm (770mV/mW) 155

156 ZERO BIAS SCHOTTKY DETECTOR PMI MODEL: DD-1G18G-ZBS-SMF Frequency Range 1.0 to 18.0GHz VSWR 8.0:1 Typical Frequency Flatness ±1.0dB Typical Output Polarity Positive Input Power 100mW, Derated to zero at +150 C Input RF Connector SMA Male Output RF Connector SMA Female Size 1.081" x 0.705" x 0.290" Finish Gold Plated 156

157 DC-COUPLED DIRECTIONAL DETECTOR PMI MODEL: DD Frequency Range Insertion Loss Insertion Loss Variation 2.5 GHz to 3.5 GHz 0.5 db 0.2 db (Over Frequency) VSWR Input 1.25:1 Impedance Minimum Directivity Maximum RF Input Maximum Output Voltage Video Bandwidth 50 ohm 20 db (Narrow Band Only) 3 Watts dbm to dbm 10 MHz Power Plus +15V Power Minus -15V Size 2.44" x 1.50" x 0.77" Weight <4 oz. 157

158 6 to 18GHz RF FILTER/DETECTOR PMI Model No: RFFD PMI MODEL RFFD IS A 6 TO 18GHz LOW PASS FILTER COMBINED WITH A SCHOTTKY BIASED DETECTOR INCLUDING A REVERSE VOLTAGE PROTECTION DIODE, A DUPLICATE DETECTOR AND PROTECTION DIODE IS INCLUDED FOR DC OFFSET VOLTAGE COMPENSATION. Frequency Range Return Loss Maximum Input Power Filter Rejection Voltage Sensitivity Barrier Potential Operating Dynamic Range 6 to 18GHz -10dB 7dBm Operational 20dBm Survival 23dB min. (20 to 26GHz) 80 to 140mV 225 to 270mV with 100uA bias to +25 Deg. C -23 to +7dBm Frequency Flatness ±0.8dB with 1dB to 2dB typical slope Diode Voltage Protection Tracking Detector-Balance 1.0V max. at 30mA ±20mV max. over operating temperature Connectors: RF Input: Filed Replaceable Video Output : Field Replaceable DC Connections SMA(M) SMA(F) Feed-thru Solder Pins Size 1.60" x 1.59" x 0.6" 158

159 12 - LOG AMPLIFIERS 159

160 PMI MODEL: SDLVA MHz Fo, LIMITED IF OUTPUT LOG AMP Frequency Range Dynamic Range VSWR In/Out Logging Range Limited IF Output Maximum RF Input Power Log Video Output Output Coupling Maximum Output Voltage 55 to 65 MHz 80 db Minimum 1.5:1 Maximum -80 to 0 dbm Typical 0 dbm Typical +10 dbm Maximum DC 2.7 Volts Rise Time 20 nsec Maximum Fall Time 30 nsec Maximum Pulse Width <100 nsec Slope 25 mv/db Nominal Log Slope Variation with Temperature ±1 mv Nominal Propagation Delay 10 nsec Typical Video Load 100Ω Typical DC Power Supply +V ma -V ma Size 3.75" x 1.50" x 0.50" 160

161 PMI MODEL: SDLVA M2G-10DBM 100MHz TO 2.0GHz, 10dBm LIMITED IF OUTPUT Frequency Range Dynamic Range Log Linearity Log 100MHz Minimum Log Range Maximum Log Range VSWR Input Tangential Sensitivity Limited IF Output Maximum RF Input Power Log Video Output Coupling Log Video Maximum Output Voltage Log Video Output Rise Time Log Video Output Fall Time Log Video Output Settling Time Log Video Output DC Offset Log Video Output Slope Log Video Output Variation with Frequency Log Video Output Variation with Temperature 0.1 to 2.0GHz 70dB Min, 75dB Typ. ±2.0dB MAX. (-65 dbm to +5dBm), ±2.0dB MAX. (-50dBm to +5dBm) -65dBm +5dBm 2.0:1 MAX., (1.8:1 TYP). -65dBm Minimum (-70dBm TYP) +10dBm +10dBm DC 2.7 v 25 ns Maximum 30 ns Maximum 40 ns Maximum 0.1 v Nominal (Adjustable) 25 mv/db Nominal (At 1GHz) ±0.5 mv/db (Over 80 MHz RF Bandwidth) ±0.5mV/dB TYP. Log Video Propagation Delay 10ns TYP. Log Video Load 100 ohms ±10% DC Power (+V) +7 to mA DC Power (-V) -7 to mA Size 3.75 " x 1.50 " x 0.40" 161

162 PMI MODEL: SDLVA-100M700M MHz TO 700MHz, LIMITED IF OUTPUT LOG AMP Frequency Range Dynamic Range Log Linearity 100 to 700MHz 55dB minimum, 60dB typical ±1.2dB typ., ±1.2dB (-55dBm to 0dBm) 19nS Rise RISE & +5dBm 24nS Fall Log Linearity Minimum Log Voltage Maximum Log Voltage VSWR Input Tangential Sensitivity Limited IF Output Maximum RF Input Power Log Video Output Coupling Log Video Maximum Output Voltage Log Video Output Rise Time Log Video Output Fall Time Log Video Output Settling Time Log Video Output DC Offset Log Video Output Slope Log Video Output Variation with Frequency ±1.5dB typ., ±2.0dB (-60dBm to 0dBm) -55dBm (-60dBm typ.) 0dBm (+10dBm typ.) 2.0:1 max. (1.5:1 typ) -60dBm typical -10dBm minimum, -5dBm typical +10dBm DC 2.7 Volts 15ns typ., 25nsec max. 15ns typ., 30nsec max. 40ns maximum 0.1 Volts Nominal (Adjustable) 25mV/dB Nominal ±5mV/dB ±0.5mV/dB typ. (Over 80MHz RF Bandwidth) Log Video Output Variation with Temperature ±1mV/dB typ. Log Video Propagation Delay 10ns Maximum, 7nS Typical Log Video Load 100 ohms ±10% DC Power (+V) +12 to mA DC Power (-V) Size 3.75 " x 1.50 " x 0.50" Finish Gold Plated -12 to mA Note: Do not supply +V without -V supplied as well as this may damage the unit 162

163 13 - PULSE & BI-PHASE MODULATORS 163

164 PMI MODEL: BPM-1G2G-1-SFF 1.0GHz TO 2.0GHz, BI-PHASE MODULATOR Frequency Range Insertion Loss 1.0 to 2.0GHz 8.8dB Max. VSWR 2.0:1 Amplitude Balance 0.25dB Typ., 0.75dB Max. 8.0nS Fall Phase Balance Carrier Suppression Impedance Switching Speed Data Signal RF Input Power RF Connectors Power Supply ±2 Typ., ±5 Max. -30dBc Typ. 50 Ohms 5nsec Typ. (50% Control to 90% RF) TTL Compatible -3dBm Max. SMA - Female 25mA Typ. Size 2.0" x 1.0" x 0.5" Weight 1.5 oz. Typ. 5.2nS Rise Finish Painted Gray 164

165 PMI MODEL: PS GHz TO 18.0GHz, BI-PHASE MODULATOR FREQUENCY RANGE INSERTION LOSS VSWR INPUT OPERATING INPUT POWER MAXIMUM RF INPUT LOG VIDEO OUTPUT RISE TIME 9 to 9.5 GHz 2.0 db MAXIMUM 1.8:1 TYPICAL +20 dbm OPERATING 0.5 WATT CW, 1uS PULSE WIDTH SURVIVAL 100 ns MAXIMUM LOG VIDEO OUTPUT SETTLING TIME 100 ns MAXIMUM CARRIER SUPPRESSION 20 db TYPICAL POWER PLUS +/-5 +/-50 ma MAXIMUM POWER MINUS +/-5 +/-50 ma MAXIMUM SIZE 1.0" X 1.0" X 0.5" WEIGHT <1.5 OUNCES 165

166 PMI MODEL: PS F 1.0GHz TO GHz, BI-PHASE MODULATOR Frequency Range Insertion Loss Return Loss (VSWR) Switching Speed Switching Rate Switching Type 1.0 to 1.12GHz 2.0 db Maximum 1.7:1 Maximum 30nsec Maximum Not less than 4MHz Hot (RF present during switching as it is for CW operation) Phase States 0 / 180 RF Input Power RF Connectors Control Power Supply +20dBm CW Maximum SMA - Female TTL 30mA Typical 2mA Typical Size 1.0" X 1.0" X 0.50" Weight Finish 2.0 oz. Painted Gray 166

167 PMI MODEL: PS-180-4R15R3-SFF 4.1GHz TO 5.3GHz, BI-PHASE MODULATOR Frequency Range 4.1 to 5.3GHz Insertion Loss 3.0dB Max. Phase Shift 180 ± 4 VSWR 1.7:1 Impedance 50 Ohms Switching Speed 100nsec Max. Control Logic TTL Compatible "0" = 0 Degrees "1" = 180 Degrees RF Input Power (Survival) +30dBm Max. RF Connectors SMA - Female Power Supply 50mA Max. and 50mA Max. Size 1.0" x 1.0" x 0.5" Finish Painted Gray 167

168 PMI MODEL: PS GHz TO 12.0GHz, BI-PHASE MODULATOR FREQUENCY RANGE INSERTION LOSS 6.0 TO 12.0GHz 2.5 db TYPICAL, 3.0 db MAXIMUM VSWR INPUT 2.0:1 OPERATING INPUT POWER SPEED MAXIMUM RF INPUT +20 dbm OPERATING 75 ns MAXIMUM ON/OFF 0.5 WATT CW, 1uS PULSE WIDTH SURVIVAL CARRIER SUPPRESSION 20 db TYPICAL POWER PLUS ma MAXIMUM POWER MINUS ma MAXIMUM SIZE 1.0" X 1.0" X 0.5" WEIGHT <2 OUNCES 168

169 14 - PHASE SHIFTERS 169

170 6-Bit Digital Phase Shifter PS M930M-6-SFF Frequency Range Insertion Loss VSWR Switching Speed RF Input Power (Operating) Control LSB 900 to 930MHz 7dB typical, 7.5dB max. 2.0:1 typical 250nsec typical, 1usec max. +14dBm CW Max. 6 BIT TTL 5.6 degrees DC Voltage 35mA typical 0mA typical Size 2.0" X 2.1" X 0.5" RF Connectors Control & Power Connector Finish SMA - Female 15 Pin Sub-D (male) Painted Gray 170

171 9-Bit, 360, Digital Phase Shifter PMI MODEL No: PS-100M1200M-9B-SFF Frequency Range Control Insertion Loss Phase Shift Amplitude Error Phase Shift Error Switching Speed 0.1 to 1.2 GHz 9-Bit TTL 13 db max. 360 typ ±1.0 db typ ±10 typ 500 nsec max SWITCHING SPEED Power Supply ma typ ma typ Size 4.95" X 3.38" X 1.00" Weight Connectors (RF) Control (Connector) Finish 14 oz. SMA(F) 15 Pin Sub-D (male) Painted Blue 171

172 9-Bit, 360, Digital Phase Shifter PMI MODEL No: PS-100M1200M-9B-SFF 172

173 Digitally Controlled 360 Degree Phase Shifter PS D5-6-SFF-1 Frequency Range Insertion Loss VSWR Phase Accuracy Switching Speed MHz ± 1MHz 5dB Typical, 8.0dB Max. 2.0:1 Typical ±8.0 typical 200nsec typ., 250nsec Max. RF Input Power - Operating 21% Duty Cycle Max. RF Input Power - Survival Control LSB DC Voltage +33dBm CW Max. 6 BIT TTL 5.6 degrees 6mA Typical 6mA Typical Size 2.0" X 2.1" X 0.5" RF Connectors SMA - Female Control & Power Connector Finish 15 Pin Sub-D (male) Painted Gray 173

174 360 Degree, Digital Phase Shifter PS-360-2D42D5-10-SFF Frequency Range Insertion Loss VSWR Phase Accuracy Switching Speed RF Input Power Control LSB Positive DC Voltage 2.4 to 2.5GHz 4dB Typical 1.75:1 Max. ±1.0 typical 500nsec max., 300nsec Typ. +20dBm CW Max. 10 BIT TTL 0.36 degrees 50mA Typ. Size 2.0" X 2.1" X 0.5" RF Connectors Control & Power Connector SMA - Female 15 Pin Sub-D (male) 174

175 360 Degree, Digital Phase Shifter PS-2D2G-360-CD-1 Frequency Range RF Input Power RF Input Power (Survival) Insertion Loss Insertion Loss vs. Frequency Insertion Loss vs. Temperature 2170 to 2200MHz 10dBm Max. +15dBm Max. 13dB Typical, 19dB Max. ±0.25dB Max. ±1.0dBpp Typical (Over any 15ºC Temp. Range) Insertion Loss vs. Phase ±0.3dB Goal, ±0.5dB Max. Phase Control Range 360 Degrees Phase vs. Temperature ±2 Degrees Typ. (Over any 15ºC Temp. Range) RF Impedance 50 Ohms Resolution <1 Degree Typ. Phase Accuracy ±1.0 typical IP3 +25dBm Typ. Switching Speed 350nsec Typ. Control 9 BIT TTL LSB 0.7 degrees Input VSWR 1.3:1 Max. Output VSWR 1.4:1 Max. Positive DC Voltage 50mA Typ. Size 2.0" X 2.1" X 0.5" RF Connectors SMA - Female Control & Power Connector 15 Pin Sub-D (male) 175

176 360 Degree, Digital Phase Shifter PS-2D2G-360-CD-1 Frequency Range RF Input Power RF Input Power (Survival) Insertion Loss Insertion Loss vs. Frequency Insertion Loss vs. Temperature 2170 to 2200MHz 10dBm Max. +15dBm Max. 13dB Typical, 19dB Max. ±0.25dB Max. ±1.0dBpp Typical (Over any 15ºC Temp. Range) Insertion Loss vs. Phase ±0.3dB Goal, ±0.5dB Max. Phase Control Range 360 Degrees Phase vs. Temperature ±2 Degrees Typ. (Over any 15ºC Temp. Range) RF Impedance 50 Ohms Resolution <1 Degree Typ. Phase Accuracy ±1.0 typical IP3 +25dBm Typ. Switching Speed 350nsec Typ. Control 9 BIT TTL LSB 0.7 degrees Input VSWR 1.3:1 Max. Output VSWR 1.4:1 Max. Positive DC Voltage 50mA Typ. Size 2.0" X 2.1" X 0.5" RF Connectors SMA - Female Control & Power Connector 15 Pin Sub-D (male) 176

177 2 to 6 GHz, 360 Degree, Digital Phase Shifter PMI MODEL No: PS-2G6G-8B-SFF 177

178 2 to 6 GHz, 360 Degree, Digital Phase Shifter PMI MODEL No: PS-2G6G-8B-SFF PHASE 0dBm 25ºC Switching Speed Yellow: RF Output 0º to 180º Green: TTL Input 178

179 5.4 to 5.9GHz, DIGITAL 360º PHASE SHIFTER PMI MODEL: PS QQ1470 Frequency RF Impedance -(Nominal) 5.4 to 5.9GHz 50 Ohms Voltage 90mA 60mA Logic Input TTL Control Phase Shift (Min) 360º Step Size (LSB) 1.41º LSB Insertion Loss (Max) 6.0dB 0º Phase Shift Amplitude Ripple (Max) VSWR (Max) Switching Speed Temperature Compensation Monoticity RF Power (Operating) Peak or Continuous Wave +/-1.5dB 2.0:1 (Input/Output) 200ns Maximum phase drift shall be no more than +/-5º or +/-5%, whichever is greater, over the specified temperature range. Guaranteed 10mW Connectors RF In/Out SMA(F) Power and Controls Male 15 Pin Subminiature "Micro D" Connector Size 6.0" x 2.5" x 0.8" 179

180 5.4 to 5.9GHz, DIGITAL 360º PHASE SHIFTER PMI MODEL: PS QQ

181 8 to 10 GHz, 360º PHASE SHIFTER PMI MODEL: PS-360-DC-1R opt. 810 FREQUENCY RANGE INSERTION LOSS VSWR PHASE ACCURACY SWITCHING SPEED POWER HANDLING CONTROL POWER PLUS POWER MINUS 8.0 GHz TO 10.0 GHz 11.5 db MAXIMUM 1.75:1 MAXIMUM ±10 DEGREES 500 nsec +20 dbm (+30 dbm SURVIVAL) 10 BIT TTL 200 ma MAXIMUM, +12V TO 100 ma MAXIMUM -12V TO 70 ma MAXIMUM SIZE 4.95" X 3.38" X 1.02" WEIGHT 13 OUNCES TYPICAL 181

182 8 to 10 GHz, 360º PHASE SHIFTER PMI MODEL: PS-360-DC-1R opt

183 9 to 11 GHz, 360º PHASE SHIFTER PMI MODEL: PS-9G11G-260-A-SFF Frequency Range RF Impedance Phase Shift Range Phase Accuracy Insertion Loss VSWR Voltage Control Range Speed Operating Input Power DC Supply 9.0 to 10.0GHz 50 Ohms 0 to 360 Degrees ±10 Degrees Typ. 7dB Typ., 10dB Max. 1.75:1 Typ to +7.5VDC 150nsec Typ. +10dBm CW Typ. +15VDC, 30mA Size 4.95" x 3.38" x 1.02" Weight Finish 13 ounces Typ. Painted Gray 183

184 8 to 10 GHz, 360º PHASE SHIFTER PMI MODEL: PS-360-DC-1R opt

185 DIGITAL 360º PHASE SHIFTER PMI MODEL: PS-360-DC-3, Opt. 911 FREQUENCY RANGE: 9 TO 11 GHz INSERTION LOSS: 10 db typical, 12 db Maximum SWITCHING SPEED: 50 ns Maximum RISE/FALL TIME: 20 ns Maximum VSWR INPUT/OUTPUT: 2.0:1 Maximum TRANSLATION RATE: 500 KHz (4 Most Significant Bits) CARRIER SUPPRESSION: > 20 dbc SIDEBAND SUPPRESSION: > 15 dbc PM / AM: ±2.0 db Max. DC POWER: +12 VOLTS@115mA (Max.), -12 VOLTS@20mA (Max.) 185

186 DIGITAL 360º PHASE SHIFTER PMI MODEL: PS-360-DC-3, Opt. 911 SPEED DATA - 0º to 180º PHASE SHIFT 10GHz +15dBm Input 186

187 DIGITAL 360º PHASE SHIFTER PMI MODEL: PS-360-DC-3, Opt. 618 FREQUENCY RANGE: 6 TO 18 GHz INSERTION LOSS: 10 db typical, 12 db Maximum SWITCHING SPEED: 50 ns Maximum RISE/FALL TIME: 20 ns Maximum VSWR INPUT/OUTPUT: 2.0:1 Maximum TRANSLATION RATE: 500 KHz (4 Most Significant Bits) CARRIER SUPPRESSION: -18 dbc (6 to 8 GHz), -25 dbc (8 to 18 GHz) SIDEBAND SUPPRESSION: -15 dbc (6 to 8 GHz), -20 dbc (8 to 18 GHz) PM / AM: ±2.5 db Max. (6 to 8 GHz), ±1.7 db Max. (8 to 18 GHz) DC POWER: + 5 VOLTS@115mA (Max.), -12 VOLTS@20mA (Max.) 187

188 DIGITAL 360º PHASE SHIFTER PMI MODEL: PS-360-DC-3, Opt. 618 HARMONICS - WORST CASE (6 to 8 GHz) 188

189 32 to 37GHz, 8-Bit Digital, Phase Shifter PMI MODEL No: PS FF Frequency 32.0 to 37.0GHz Insertion Loss 13.0dB typ VSWR 2.0:1 typ LSB Control Bits 8 line (TTL Control) Switching Speed 500 ns Maximum Power Supply 90mA Maximum 60mA Maximum Connectors 2.92mm Female Input & Output Size 1.150" X 1.800" X 0.4" 189

190 32 to 37GHz, 8-Bit Digital, Phase Shifter PMI MODEL No: PS FF SWITCHING SPEED (FALL TIME / DELAY OFF) SWITCHING SPEED (FULL PULSE) 190

191 INTEGRATED PHASE SHIFTER & ATTENUATOR PMI MODEL: PSAT B-CD-1 SPECTRAL ANALYSIS - CARRIER HARMONIC SUPRESSION 191

192 INTEGRATED PHASE SHIFTER & ATTENUATOR PMI MODEL: PSAT B-CD-1 192

193 INTEGRATED PHASE SHIFTER & ATTENUATOR PMI MODEL: PSAT B-CD-1 193

194 15 - RACK & CHASSIS MOUNT PRODUCTS 194

195 RACK & CHASSIS MOUNT PRODUCTS PMI offers various RF and Microwave products that range from 250kHz up to 40.0GHz which are supplied in a ruggedized, 1U to 6U chassis. Many options are available. If you do not see exactly what you require on this web site please contact us because we offer amplifiers designed and built to your specifications at catalog prices. Our ruggedized, military grade chassis products are built to meet your exact application needs: Amplification Attenuation (Digital Solid-State) Switching (Ultra High Speed) Power Detection / Fault Detection Phase Shifting / Phase Modulation Pulse Modulation Noise Generation RF Filtering RF Limiting Power Splitting RF Signal Distribution 195

196 RACK & CHASSIS MOUNT PRODUCTS 1U 19" Rack Mount Amplifiers PMI offers a full line of RF and Microwave Amplifiers that range from 250kHz up to 40.0GHz. Any of our standard amplifiers or amplifiers that are built to meet your specifications can be supplied in a ruggedized, 1U chassis. Many options are available. If you do not see exactly what you require on this web site please contact us because we offer amplifiers designed and built to your specifications at catalog prices. Features that are supplied with all of our rack mount amplifiers: Internal AC Power Supply. (120VAC standard - 220VAC available) Internal Fuse Protection Unconditional Stability Each unit has a unique serial number and date code. Swept Data with each unit. (S21, S11, S22 and Noise Figure) Summary data sheet with each unit. Operating Temperature -20 to +70 C Rack Mount Amplifier Options: Digital control and interface for gain control, power on / off, and other features are available. Connector types can be specified. Gain and OP1dB values can be optimized to meet your requirement. Operating temperature ranges can be increased to -54 C to +85 C. All amplifiers can be optimized to your specific frequency of interest. Temperature Compensation is available on all amplifiers. Military or Space Screening is available. Gain and Phase matching is available on most amplifiers. 196

197 16 - UP & DOWN CONVERTERS RECIEVER FRONT ENDS & TRANSCEIVERS 197

198 4 to 18GHz, UP/DOWN CONVERTER PMI MODEL: PUC-4G18G-CD-1 PMI MODEL NUMBER PUC-4G18G-CD-1 IS AN AMPLIFIED UP/DOWN- CONVERTER FOR THE FREQUENCY RANGE OF 4GHz TO 18GHz WITH AN IF RANGE OF 10MHz to 100MHz. IT FEATURES A 32dB PROGRAMMABLE ATTENUATOR WITH 10-BIT RESOLUTION, AND AN OUTPUT AMPLIFIER TO PROVIDE CONVERSION GAIN. IT ALSO FEATURES AN IF TRANSFER SWITCH TO SELECT THE UPPER OR LOWER SIDEBAND. 198

199 4 to 18GHz, UP/DOWN CONVERTER PMI MODEL: PUC-4G18G-CD-1 CONVERSION GAIN IF=10MHz RETURN LOSS LO (S11) & RF (S22) CONVERSION GAIN IF=100MHz 199

200 PMI MODEL: PIFA-9D4G-1D8G-1 DOWN CONVERTER PMI Model No. PIFA-9D4G-1D8G-1 is an integrated frequency down converter used within Doppler Radar Systems. The RF Input is 9.4GHz +/- 30Mhz with an input dynamic range of 100 to 0dBm. The LO Input is 2.803GHz +/- 15Mhz with a power level of +5 to +7dBm. The resulting IF Output Frequency is 1.8GHz +/- 10MHz. The RF to IF gain is 10dB to 13dB. This module incorporates internal RF, IF and LO filtering and amplification for optimum out of band rejection and superior electrical performance. The group delay ripple from RF to IF Output is less than 0.1ns over a 20MHz bandwidth. The OIP3 is greater than 25dBm. The module operates on single supply of +12 volts and is supplied with SMA female connectors in a package measuring 1.8" x 1.15" x 0.4". 200

201 PMI MODEL: PIFA-9D4G-1D8G-1 DOWN CONVERTER RX Frequency Range (J1) RX Power Range (J1) RX High Pass Filter (J1) LO Input Frequency (J2) LO Input Power (J2) LO Band Pass Filter (J2) LO Frequency to Mixer (J2) IF Output Power (J3) IF Frequency (J3) IF Bandpass Filter (J3) VSWR Noise Figure at Input (J1) Gain (J1 to J3) Group Delay Ripple (J1 to J3) OP3 (Output) OP2 (Output) Output Signal Distortion Stability Power Supply Power Supply Rejection 9.41GHz +/- 30MHz -100dBm to 0dBm 8.0GHz Corner Frequency nom 3.803GHz +/- 15MHz +5dBm to +7dBm 7.2 to 8.5GHz (-3dB IL Nom) 7.610GHz +/- 30MHz 13dBm max 1.8GHz +/-10MHz 75MHz Passband (-3dB nom) 1.5:1 max (1.3:1 Preferred) 8dB max 10dB min, 13dB max -0.1nsec/ 20MHz >25 dbm (>28dBm Preferred) >15dBm (>18dBm Preferred) The module must be unconditionally stable when terminated at J1, J2 and J3 with a short circuit in all phases Now apparent droop or distortion with a pulse width of 500 to 1000 nsec at 500 to 2000 pps. 1A max 0.1dB/Volt max RF Connectors SMA Jacks Size 1.8" x 1.15" x 0.4" 201

202 PMI MODEL: PTRAN-100M18G-70-MAH OPEN VPX TRANSCEIVER (PHASEII) PMI Model No. PTRAN-100M18G-70-MAH is a transceiver covering the frequency range of 100MHz to 18.0GHz. This unit up-converts a 100MHz to 4.0GHz transmit signal to the 2.0 to 18.0GHz frequency range. It also down-converts a 100MHz to 18.0GHz received signal to the 100MHz to 4.0GHz intermediate frequency range for analog to digital conversion. This is supplied in Open VPX architecture. 202

203 PMI MODEL: PTRAN-100M18G-70-MAH OPEN VPX TRANSCEIVER (PHASEII) 203

204 PMI MODEL: PTRAN-100M18G-70-MAH OPEN VPX TRANSCEIVER (PHASEII) Frequency 100MHz to 18.0GHz Inputs J3, J5, J7, J8 J3 Input Input from RX Filter Bank Frequency 100MHz to 18.0GHz Power Level -74dBm to -4dBm +/-3dBm (Assuming 6dB +/-3.5dB Gain in RX Filter Bank) J5 Input IF Input from Backplane Frequency 100MHz to 4.0GHz Power Level 0dBm typ J7 Input LO1 from Backplane Frequency 4.0GHz to 20GHz Power Level +15dBm typ J8 Input LO2 from the Backplane Frequency 4.0GHz to 20GHz Power Level +15dBm typ Outputs J2, J4, J6 J2 Output to TX Filter Bank Frequency 100MHz to 18.0GHz Power Level Undefined (Allow for 0 to +10dBm Out of TX Filter Bank) J4 IF Output to Backplane Frequency 100MHz to 4.0GHz Power Level 0dBm typical for Non-Linear SDLVA Channels J6 Output to RS Filter Bank Frequency 100MHz to 18.0GHz Power Level Undefined Control Logic LVDS Power Supplies +12V, -12V, +5V, +3.3V Size 5.55" x 3.68" x 0.89" RF Connectors Digital Connectors Finish Operating Temperature SMA(F) 30 Pin Headers to Connect to inrevium TB-FMCL-PH Board Painted Gray - Epoxy Polomide Coating IAW MIL-C-22750, Type I over Epoxy Polomide Primer IAW MIL-P-23377, Type I, Class 1 or 3-40 deg C to +85 deg C 204

205 PMI MODEL: PTRAN-100M18G-70-MAH OPEN VPX TRANSCEIVER (PHASEII) 205

206 PMI MODEL: PTRAN-100M18G-70-MAH OPEN VPX TRANSCEIVER PHASE III PMI Model No. PTRAN-100M18G-70-MAH (PHASEIII) is a transceiver covering the frequency range of 100MHz to 18.0GHz. This unit up-converts a 100MHz to 4.0GHz transmit signal to the 2.0 to 18.0GHz frequency range. It also down-converts a 100MHz to 18.0GHz received signal to the 100MHz to 4.0GHz intermediate frequency range for analog to digital conversion. This is supplied in Open VPX architecture. 100 MHz to 18.0 GHz Transceiver Less than 30 Watts Total Power Consumption Time Gated SDLVA for Pulse Blanking Up to 4 GHz Instantaneous Bandwidth -80 to -10 dbm Input Dynamic Range Customizable Switched Filter Banks 0 to +10 dbm Transmit Power 100 ns Switching Speed VITA 07 RF Interface CW Immunity Over 300% Smaller than Individual Components While Still Maintaining 100 db Isolation 206

207 PMI MODEL: PTRAN-100M18G-70-MAH OPEN VPX TRANSCEIVER PHASE III Frequency Gain Isolation Switching Speed Inputs J1 Input: Frequency Power Level J6 Input Frequency Power Level Outputs J3 Output: Frequency Power Level Thru Channel Passband Number of Filter Channels Channel 1 Center Frequency 3dB Bandwidth Rejection Channel 2 Center Frequency 3dB Bandwidth Rejection Channel 3 Center Frequency 3dB Bandwidth Rejection Channel 4 Center Frequency 3dB Bandwidth Rejection Channel 5 Center Frequency 3dB Bandwidth Rejection 100MHz to 18.0GHz 18dB Typ J1, J6 100dB 100ns J1, J6 Input from Backplane 100MHz to 18.0GHz -80 dbm to -10 dbm Output to Transceiver 100Mhz to 18.0GHz -52 dbm to -22 dbm J3 Output to Transceiver 100MHz to 18.0GHz -74 dbm to -4dBm typ 100MHz to 18.0GHz 5 Channels 3400MHz 2000MHz -40 dbc, typ (100MHz to 2GHz), -30dBc min -40dBc typ (4.8 to 8.5GHz), -30dBc min 5400MHz 2000MHz -40 dbc typ (100MHz to 4GHz), -30dBc min -40 dbc typ (6.8 to 13.5GHz), -30dBc min 7400MHz 2000MHz -40 dbc typ (100MHz to 6GHz), -30dBc min -40 dbc typ (8.8 to 18GHz), -30dBc min 9400MHz 2000MHz -40 dbc typ (100MHz to 8GHz), -30dBc min -40 dbc typ (10.8 to 18GHz), -30dBc min 11400MHz 2000MHz -40 dbc typ (100MHz to 10GHz), -30dBc min -40 dbc typ (12.8 to 18GHz), -30dBc min Control Logic 3.3V TTL Power +12V, -12V, +5V, +3.3V Connectors SMA (F) Digital/Power Connector 15PIN Micro-D Mating Connector Provided Size 4.925" x 3.68" x 0,35" Finish Painted Gray Operating Temperature -40ºC to +85 ºC 207

208 PMI MODEL: PTRAN-100M18G-70-MAH OPEN VPX TRANSCEIVER PHASE III PHASEIII TRANSCEIVER RECEIVE SIDE SWITCH FILTER BANK PHASEIII TRANSCEIVER FULLY ASSEMBLED PHASEIII TRANSCEIVER TRANSMIT SIDE SWITCH FILTER BANK 208

209 PMI MODEL: PTRAN-100M18G-70-MAH OPEN VPX TRANSCEIVER PHASE III 209

210 17 - SINGLE SIDEBAND MODULATORS 210

211 PMI SINGLE SIDEBAND MODULATORS PMI MODEL: PSM-0R5G2R5G-CD-1 INPUT PARAMETERS: RF Carrier: 0.5 to 2.5 GHz RF VSWR (RF= -10dBm, IF Modulation +10dBm: 2.0:1 Typ. RF Power at 1dB Compression Point (IF=+10dBm): +5dBm Typ. IF Modulation Frequency Range: DC to 500MHz IF Modulation Power Range (50Ω): +7dBm Min, +13dBm Max. Transfer Characteristics: Conversion Loss: 13.5dB Max. (See Note #1) Carrier Suppression: 20dBc Min., 23dBc Typ Fundamental IF: 15dBc Min. Carrier: ±21F, 41F, etc.: 35dBc Typ. Carrier ±31F: 7dBc Typ. Quadrature Phase Accuracy, I/Q Mode: ±7.5º Typ, ±10º Max. Quadrature Amplitude Accuracy: ±1.5dB Typ., ±2.0dB Max. 0.5 to 2.5GHz 13.5dB Max. Conversion Loss 20dBc Carrier Suppression 5dBm Typ OP1dB 2:1 VSWR ±10º Quadrature Phase Accuracy OUTPUT PARAMETERS: RF Frequency Range: 0.5 to 2.5GHz RF VSWR (RF=-10dBm, IF Modulation= +10dBm: 4.0:1 Typ. FINISH: Nickel Plate Dimensions: 2.5 X 2.0 X 0.50 Note #1: Insertion Loss relative to 0dBm RF Input All Other Outputs including f0 are relative to the desired upper (f0+fm) Output. 211

212 PMI SINGLE SIDEBAND MODULATORS PMI MODEL: PSM-0R5G2R5G-CD-1 INSERTION LOSS & RETURN LOSS 0º 90º 180º 270º SIDEBAND & CARRIER PRODUCTS 500 MHz 1.5 GHz 2.5 GHz 212

213 PMI SINGLE SIDEBAND MODULATORS PMI MODEL: PSM-50M1G-CD-1 INPUT PARAMETERS: RF Carrier: 0.5 to 1.0GHz RF VSWR (RF= -10dBm, IF Modulation +10dBm: 2.0:1 Typ. RF Power at 1dB Compression Point (IF=+10dBm): +5dBm Typ. IF Modulation Frequency Range: DC to 10MHz IF Modulation Power Range (50Ω): +7dBm Min, +13dBm Max. Transfer Characteristics: Conversion Loss: 10dB Max. (See Note #1) Carrier Suppression: 15dBc Min., 20dBc Typ Quadrature Phase Accuracy, I/Q Mode: ±7.5º Typ, ±10º Max. Quadrature Amplitude Accuracy: ±1.5dB Typ., ±2.0dB Max to 1.0GHz 10dB Max. Conversion Loss 15dBc Carrier Suppression 5dBm Typ OP1dB 3:1 VSWR Max ±10º Quadrature Phase Accuracy OUTPUT PARAMETERS: RF Frequency Range: 0.5 to 1.0GHz RF VSWR (RF=-10dBm, IF Modulation= +10dBm: 3.0:1 Typ. FINISH: Nickel Plate Dimensions: 6.0 X 3.5 X 1.0 Note #1: Insertion Loss relative to 0dBm RF Input All Other Outputs including f0 are relative to the desired upper (f0+fm) Output. 213

214 PMI SINGLE SIDEBAND MODULATORS PMI MODEL: PSM-50M1G-CD

215 18 - SMT & QFN PRODUCTS 215

216 QFN SMT LIMITER & AMPLIFIER PSMT to 15.5 GHz 20dB Gain 2.5dB Noise Figure +10dBm OP1dB 2.0:1 VSWR (In/Out) +30dBm Max Input 100mA 5mm X 5mm Size 32 Lead SMT Package Representative picture of QFN 5mm X 5mm housing Representative picture of how a QFN component is made 216

217 20 WATT CW, SPDT SURFACE MOUNT SWITCH PMI MODEL: P2T-14D415D4-15-SMT-20W FREQUENCY 14.4 to 15.4 GHz DESIGN SPDT SURFACE MOUNT POWER HANDLING 20 Watt INSERTION LOSS 0.5dB ISOLATION 15dB Min. SIZE 0.35 X 0.50 X 0.21 PMI Model No.P2T-14D415D4-15-SMT-20W is a driverless highpower SP2T switch in a compact package designed for surface mount applications. This switch operates from 14.4 to 15.4GHz and has an insertion loss of 1.2dB maximum at +25 C. The TX/RX isolation is 10dB minimum and this switch can handle input power levels up to 20 watts. The size of this SMT switch is 0.35" x 0.5" x 0.21". 217

218 19 - SOLID STATE SWITCHES 218

219 SOLID STATE SWITCHES 10 MHz to 40 GHz SPST to SP64T Reflective or Absorptive High Speed High Isolation Low Loss Video Filtering Options Available: Integrated Limiters or Amplifiers Phase and/or Amplitude Matching Analog or Digital Control options 219

220 18.0 to 40.0GHz, SPST, 90dB Switch P1T-18G40G FF Frequency 18.0 to 40.0GHz Average Isolation over 100dB Isolation Insertion Loss 90dB min. 5.0dB max. VSWR In/Out 2.0:1 max. Input Power +23dBm CW max. Switching Speed 25 ns max. / 15 ns typ DC Voltage +15VDC -15VDC Control Signal 0VDC "Low Loss" 5VDC "Isolation" Connectors 2.92mm (F) 220

221 8.0 to 18.0GHz, 55dB, PULSE MODULATOR PMI MODEL No: MPM-1002 PARAMETERS SPECIFIED VALUE TEST RESULTS Frequency Range: 8.0 to 18.0GHz GHz Input VSWR (50Ω): 2.0:1 Max 1.90:1 RF Input Power Handling: 0.5 Watts Min Pass Video Feedthru: +2.0V Max Pass Insertion Loss: 2.5 db Max 2.48dB RFI Leakage: 65 dbc Min >65.0dBc Harmonics: 20 dbc Min >20.0dBc Isolation: 55 db Min 61.03dB Rise Time: 20ns Max 10.2ns Fall Time: 50ns Max 18.5ns Switching Time: 80ns Max 50% I/P to 90% O/P 33.4ns DC Supply Typ 221

222 8.0 to 18.0GHz, 55dB, SPST PULSE MODULATOR PMI MODEL No: MPM-1002 SWITCHING SPEED 222

223 DC to 40 GHz, ULTRA-HIGH SPEED SWITCH PMI MODEL: P1T-DC40G-65-T-292FF PMI MODEL P1T-DC40G-65-T-292FF-1NS IS AN ULTRA- HIGH SPEED (1nS), ABSORPTIVE, SINGLE POLE SINGLE THROW PIN DIODE SWITCH THAT OPERATES FROM DC TO 40 GHz. THIS MODEL INCORPORATES A TTL COMPATIBLE DRIVER FOR EASY SYSTEM INTEGRATION. Frequency Isolation Insertion Loss VSWR In/Out Input Power Switching Speed Rise/Fall Time Control Signal DC to 40.0GHz 65dB typ, 55dB min 5.5dB typ, 6.8dB max 2.0:1 typ, 2.2:1 max +17 dbm CW max 5ns typ, 6ns max Measured 2.7ns 0.9ns typ, 1ns max Measured 0.6ns TTL "1" = On DC Voltage +8 to max Measured 8mA -8 to 40mA max - Measured 27mA Connectors In/Out Control Connectors 2.92mm(F) SMC Size 1.2" x 1.3" x 0.5" 223

224 DC to 40 GHz, ULTRA-HIGH SPEED SWITCH PMI MODEL: P1T-DC40G-65-T-292FF 224

225 500MHz to 40 GHz, HIGH SPEED SWITCH PMI MODEL: P1T-500M40G-55-T-292FF PMI Model No. P1T-500M40G-55-T-292FF is an SPST, High Speed, Absorptive Switch. This switch operates at a frequency range of.5 to 40.0GHz and is capable of switching within 100ns. It has 55dB of Isolation and insertion loss of 5.5dB max. Frequency Isolation Insertion Loss VSWR In/Out Operating Input Power Switching Speed DC Voltage 0.5 to 40.0GHz 74dB typ, 55dB min. 5.5dB max. 2.0:1 typ, 2.5:1 max. +20dBm CW max 25nsec typ, 100nsec max. 20mA typ Control Signal TTL Compatible "0" = On "1" = Off Connectors Finish 2.92mm (F) Painted Gray Size 1.0" x 1.0" x 0.5" 225

226 24GHz to 40 GHz, HIGH SPEED SWITCH PMI MODEL: P1T-24G40G-55-T-292FF PMI MODEL P1T-24G40G-55-T-292FF-23DBM IS AN ABSORPTIVE, HIGH SPEED, SINGLE POLE SINGLE THROW SWITCH WITH A RISE/FALL OF 10ns AND A SWITCHING SPEED OF 25ns.THE FREQUENCY RANGE IS 24 TO 40 GHz WITH > 55 db ISOLATION. THE INPUT P1dB IS > 23 dbm. PARAMETERS SPECIFIED VALUE TEST RESULTS Frequency Range: 24 to 40 GHz 24 to 40 GHz Isolation: 55 db Min dB Insertion Loss: 5.5 db Max. 4.16dB VSWR: 2.5:1 Typ. 2.29:1 Input Power: +23dBm CW Min P1dB +23dBm CW Min P1dB RF Switching Speed: 25ns Max. 22ns Typ. Rise/Fall: 10ns Max. 9ns Typ. DC Voltage: ±5V +5V 20mA -5V 63mA Control Signal: TTL Compatible 0 = Insertion Loss 1 = Isolation Pass 226

227 PMI MODEL: P2T-1G18G-10-R-5V-SFF-HIP10W SP2T, 10 WATT, REFLECTIVE, SOLID STATE SWITCH 1.0 TO 18.0 GHz Frequency Range 10 Watt Input Power Handling 5 VDC Single Supply 4.0dB Insertion Loss Max. 100nS Switching Speed Max. Frequency Isolation Insertion Loss VSWR In/Out 2.0:1 Operating Input Power 1.0 to 18.0GHz 25dB typ, 10dB min 2.5dB typ, 4.0dB max 5W CW max. (Not to be switched any higher than 50kHz [PRI]) 1dB Compression RF Switching Speed Impedance DC Voltage and Current Control Signal Connectors Finish +40dBm Goal <40ns typ, 100ns max 50 ohms 35mA typ TTL Logic SMA(F) - Removable Painted Gray Bottom side - Unpainted Size 1.2" x 1.0" x 0.5" 227

228 PMI MODEL: P2T-5G5D15G-30-R-528-SFF-20W SP2T, REFLECTIVE, 20 WATT, PIN DIODE SWITCH 20 Watt RF Power Handling 200nS Switching Speed 2.0dB Insertion Loss Max. Frequency Insertion Loss Isolation 5000 to 5150MHz 1.5dB goal, 2.0dB max 30dB min Switching Speed 200ns typ (Customer spec of 2us max) Operating Input Power +43dBm (20W) CW max. VSWR In/Out 1.2:1 typ, 1.5:1 max RF Connectors Control SMA (F) Removable TTL DC Voltage and Current 3mA typ typ Finish Painted Gray Size 1.2" x 1.0" x 0.5" 228

229 PMI MODEL: P2T-5G5D15G-30-R-528-SFF-20W SP2T, REFLECTIVE, 20 WATT, PIN DIODE SWITCH FULL PULSE 200nS/Div. J1-J2 Insertion Loss & Return Loss J1-J2 Isolation 229

230 PMI MODEL: P2T-8G18G-45-R-SFF-HP20W SP2T, REFLECTIVE, 20 WATT, PIN DIODE SWITCH PMI Model No. P2T-8G18G-45-R-SFF-HP20Wis an SP2T, High Power(20 Watt), Reflective Switch. This switch operates on a frequency of 8.0 to 18.0GHz. It has a low insertion loss of 2.5dB max and an integral TTL driver and is hermetically sealed. Frequency Isolation Insertion Loss VSWR In / Out Rise Time Fall Time Delay On Delay Off Control Operating Input Power 8.0 to 18.0GHz 45dB min. 2.5dB max, 2.0dB typ 2.0:1 max. 75ns typ (25ns measured) 25ns typ (10ns measured) 150ns typ (55ns measured) 100ns typ (30ns measured) TTL 20W average or 1kW peak, 2% Duty Cycle DC Supply Connectors 70mA Typical 3mA Typical SMA(F) Size 1.2" x 1.0" x 0.5" Sealing Hermetic 230

231 PMI MODEL: P2T-8G18G-45-R-SFF-HP20W SP2T, REFLECTIVE, 20 WATT, PIN DIODE SWITCH J1-J2 INSERTION LOSS & RETURN LOSS J1-J2 ISOLATION & RETURN LOSS J1-J3 INSERTION LOSS & RETURN LOSS J1-J3 ISOLATION & RETURN LOSS 231

232 20 WATT CW, SPDT SURFACE MOUNT SWITCH PMI MODEL: P2T-14D415D4-15-SMT-20W FREQUENCY 14.4 to 15.4 GHz DESIGN SPDT SURFACE MOUNT POWER HANDLING 20 Watt INSERTION LOSS 0.5dB ISOLATION 15dB Min. SIZE 0.35 X 0.50 X 0.21 PMI Model No.P2T-14D415D4-15-SMT-20W is a driverless highpower SP2T switch in a compact package designed for surface mount applications. This switch operates from 14.4 to 15.4GHz and has an insertion loss of 1.2dB maximum at +25 C. The TX/RX isolation is 10dB minimum and this switch can handle input power levels up to 20 watts. The size of this SMT switch is 0.35" x 0.5" x 0.21". 232

233 100 WATT CW, SPDT, TERMINATED, SWITCH PMI MODEL: P2T-6G18G-25-T-TFF-100W Frequency Insertion Loss Isolation Phase Tracking Switching Speed Power Handling Mounting Temperature VSWR 6.0 to 18.0GHz 2.0dB Typical, 2.6dB Max. 25dB Min. ±5 Degrees. 1us Max. 100 Watts CW Min. (Absorptive Section will handle 10 Watts CW Max.) 50 Degrees C, Mounting Surface to be Gold Plated 2.0:1 Max. PMI Model No. P2T-6G18G-25-T-TFF-100W is a single pole, two throw, absorptive switch designed to operate over the 6.0 to 18.0GHz frequency range. This model is designed to handle 100 watts average input power with the absorptive section rated to handle 10 watts CW. The switch offers fast switching speeds of 1usec maximum, low insertion loss of 2.0dB typically and high isolation of 25dB minimum. These units offer phase tracking of less then ±5. The DC supplies are +28VDC and ±5VDC. The housing measures 1.79 x 0.60 x 2.03 and is supplied with TNC Female connectors. Control Bias RF Connectors Power & Control Connector 2 Bit TTL 0 = Isolation 1 = Low Loss +28VDC & ±5VDC TNC Female 9 Pin Micro-D Female, Mating with M83513/03A/03C Size 1.78" x 0.60" x 2.03" Finish Switching Type: Gold Plated Cold Switching 233

234 1.6 KILOWATT, SPDT, REFLECTIVE, SWITCH PMI MODEL: P2T-6G18G-40-R-570-TFF-1D6KW PMI Model No. P2T-6G18G-40-R-570-TFF-1D6KW is a reflective 1.6 kilowatt high-power cold switching single pole double throw switch operating in the 6.0 to18.0 GHz frequency range. Frequency Range Power 6.0 to 18.0 GHz 1.6KW Peak Duty Cycle 8% Insertion Loss Isolation Pulse Width Switching Speed VSWR In/Out 2.2dB max. At band edges for 20% bandwidth and typically 1.75 db goal. For mid-band of 80% of the bandwidth 2.0 db max., and typically 1.5 db goal. 40 db 250 usec max. 200 ns max. (50% TTL to 90% RF & 50% TTL to 10% RF) 2:1 max. Load VSWR Better than 1.5:1 DC Voltage & Current Control Connector for RF Port Connector for Control 300mA and 60mA Single TTL (TTL "0" J1 - J3 Low Loss) TNC Female 9 pin micro D type female mating with M83513/03A/03C Size (Not Incl. Connectors) 2.00" x 2.00" x 0.75" Finish Painted Blue - No Paint on Mounting Surface 234

235 1.6 KILOWATT, SPDT, REFLECTIVE, SWITCH PMI MODEL: P2T-6G18G-40-R-570-TFF-1D6KW 235

236 100 WATT CW, SPDT SWITCH PMI MODEL : PEC-9R510R7-100W-SFF-SPDT PARAMETER FREQUENCY ISOLATION INSERTION LOSS SPECIFICATION 9.5 to 10.7 GHz 40dB Min 1.5dB Typ VSWR 2.0:1 RF INPUT POWER SWITCHING SPEED 120 WATTS CW MAX 400nS Max CONTROL LOGIC 1 = J1-J2 Insertion Loss 0 = J1-J3 Insertion Loss DC POWER SUPPLY =5 500mA mA 236

237 40 WATT CW, SPDT, HIGH POWER SWITCH PMI MODEL: P2T-1G1R1G-25-R-TFF-40W PMI MODEL P2T-1G1R1G-25-R-TFF-40W IS A SINGLE POLE, TWO THROW HERMETICALLY SEALED REFLECTIVE SWITCH DESIGNED TO OPERATE OVER THE 1 GHz TO 1.1 GHz FREQUENCY RANGE. THIS MODEL IS DESIGNED TO HANDLE 40 WATTS AVERAGE INPUT POWER AND 4KW PEAK HAVING A 3uSEC PULSE WIDTH AND 1% DUTY CYCLE. Frequency Power Average Power Insertion Loss Isolation 1.0 to 1.1GHz 4KW Peak 40W 0.8dB max Measured 0.4dB 25dB min VSWR 1.5:1 Measured 1.2:1 Rise Time From 10% to 90% RF Duty Cycle 1% Pulse Width 3uS PRF 600Hz Switching Speed 300ns max Switching Rate 2KHz Cold Switching Yes Control TTL Power Supply Connectors 50mA 18mA typ. 200mA 63mA typ. 30mA 0mA (Not Used) TNC Female (J1, J2, J3), 9-Pin Micro D (DC/Control) Size 3.92" x 2.68" x 0.70" 237

238 100 WATT CW, SPDT, HIGH POWER SWITCH PMI MODEL: P2T-1G1R1G-25-R-TFF-100W PMI Model No. P2T-1G1R1G-25-R-TFF-100W is a single pole, two throw, hermetically sealed reflective switch designed to operate over the 1.0 to 1.1GHz frequency range. This model is designed to handle 100 Watts average input power and 5KW peak having a 17usec pulse width and 2% duty cycle. Frequency 1.0 to 1.1GHz Power 5KW Peak Average Power 100 Watts Insertion Loss 0.8dB max Isolation 25dBm Rise Time 275ns typ - From 10% to 90% RF Switching Delay 385ns typ - From 50% TTL to 10%- 90% RF Duty Cycle 2% Pulse Width 17uS PRF 600Hz Switching Speed 5uS max Switching Rate 2KHz Cold Switching Yes Power Supply 50mA 200mA Control TTL Connectors TNC Female (J1, J2, J3), 9-Pin Micro D (DC/Control) J4 Connections Pin 1 U1 +50V Pin 2 Ground Pin 3 U1 IN2 (CTRL J3) Pin 4 U1 +5V Pin 5 U1 IN1 (CTRL J2) Pin 6 U1 Ground Pin 7 U1 Ground Pin 8 U1 Ground Pin 9 U1 Ground Size 4.22" x 2.98" x 0.70" 238

239 Absorptive SP4T Solid State Switch P4T-10G40G-60-T-292FF Frequency Isolation Insertion Loss Insertion Loss Flatness VSWR In/Out Input Power Switching Speed (10% to 90% RF) 10.0 to 40.0GHz 60dB min. 6.0dB max. ±1dB typical over full band 2.0:1 max. 200mW CW max. (+23dBm CW) 30nsec typ. DC Voltage and Current 75mA typical 45mA typical Control Signal RF Connectors DC & Control 2-BIt Decoded TTL Logic 2.92mm Solder Pins Size 1.25" x 1.25" x 0.5" Finish Gold Plated 239

240 SP4T, Terminated, Solid State Switch P4T-10G40G-60-T-GPO Frequency Isolation Insertion Loss Insertion Loss Flatness VSWR In/Out Input Power Switching Speed (10% to 90% RF) 10.0 to 40.0GHz 60dB min. 6.0dB max. ±1dB typical over full band 2.0:1 max. 200mW CW max. (+23dBm CW) 30nsec typ. DC Voltage and Current 75mA typical 45mA typical Control Signal RF Connectors DC & Control 2-BIt Decoded TTL Logic GPO - Limited Detent Solder Pins Size 1.25" x 1.25" x 0.5" Finish Gold Plated 240

241 SP4T, PHASE MATCHED SOLID STATE SWITCH PMI MODEL: P4T-4G12G-35-R-SFF-PM PARAMETERS FREQUENCY RANGE INSERTION LOSS ISOLATION SPECIFICATIONS 4.0 TO 12.0 GHz 1.0 db Typ 35dB Min VSWR 2.0:1 SWITCHING SPEED SWITCHING RATE OPERATING RF POWER PHASE MATCHING DC POWER SUPPLY CONTROL LOGIC 20nS Typ OFF 30nS Typ ON 50nS Typ. 0dBm Max +10dBm Survival 12.0 GHz Max (Arm to Arm per Unit) +100mA / - 60mA 2-Bit Decoder 241

242 50MHz to 40GHz, SP4T, High Speed Switch P4T-50M40G-55-T-292FF Frequency 0.05 to 40.0GHz Isolation 75dB Typical, 55dB Min. Insertion Loss 5.6dB Typical, 8dB Max. VSWR In/Out Operating Input Power Switching Speed 2.5:1 max. +20dBm CW max. 100nsec max. Measured 25nsec DC Voltage and Current +12 to 150mA -12 to 100mA max. Control Signal 4-Bit TTL Independent Control Connectors 2.92mm(F) Finish Gold Plated Size 2.0" x 1.0" x 0.4" 242

243 100MHz to 40GHz, SP4T, High Isolation Switch P4T-100M40G FF-SP Frequency Isolation 0.1 to 40.0GHz >100dB typ. (0.1 to 18GHz) >95dB typ. (18 to 26.5GHz) >77dB typ. (26.5 to 40GHz) Insertion Loss 6dB typ. (0.1 to 18GHz) - Measured 3.85dB 8dB typ. (18 to 26.5GHz) - Measured 5.15dB 10dB typ. (26.5 to 40GHz) - Measured 5.58dB VSWR In/Out Operating Input Power Switching Speed 2.0:1 typ., 2.75:1 max. +20dBm CW max. 100nsec max. Measured 25nsec "On" Measured 75nsec "Off" DC Voltage and Current 200mA max, 120mA typ. 100mA max., 65mA typ. Control Signal 2-Bit Decoded TTL Connectors 2.92mm(F) Finish Gold Plated Size 2.0" x 1.0" x 0.4" 243

244 PMI MODEL: P5T-500M40G-60-T FF SP5T, TERMINATED, SOLID STATE SWITCH Frequency Isolation Insertion Loss VSWR In/Out 0.5 to 40.0GHz (Optimized for 5.0 to 40.0GHz) 74dB Typical, 60dB min. 6dB Typical, 8.0dB max. 2.5:1 max. Operating Input Power +20dBm CW max SP5T, Terminated, Switch 500 MHz to 40 GHz Frequency Range 50nS On/Off Switching Speed Switching Speed (Rise/Fall) Switching Speed (On/Off) DC Voltage & Current Control Connectors Finish 15ns typ 40ns Typical, 50ns max 55mA Typical 45mA Typical TTL 2.92mm (F) Gold Plated 244

245 SP6T, TERMINATED, SOLID STATE SWITCH PMI MODEL: P6T-2G18G-60-T-512-SFF-LV PMI Model No. P6T-2G18G-60-T-512-SFF-LV is a single pole, six throw, absorptive, low video transient, solid state switch operating over the frequency range of 2.0 to 18.0GHz. This model has a maximum insertion loss of 4.0dB and a minimum isolation specification of 60dB with video transients of 2mV typically. It operates at 23dBm CW maximum and has a survival specification of 27dBm CW maximum and offers a typical switching speed of 30ns. The unit is supplied with removable SMA(F) connectors in a hermetically sealed housing that measures 1.5" x 2.0" x 0.4". Frequency Insertion Loss Tracking Isolation VSWR Impedance Input Power Switching Speed On Off Switching Rate PRF Video Leakage Control Logic 0 Logic 1 DC Supply 2.0 to 18.0GHz 4dB max 0.8dB window max 60dB max Measured 78dB 2.0:1 max 50 OHMS 23dBm CW max (Operating) 27dBm CW max (Survival) 50ns max Measured 30ns 50% TTL to 90% RF 50% TTL to 10% RF 5MHz 50mV Peak-Peak max Measured at 300MHz BW Measured 2mV 6 Line TTL Logic 1.6mA max 0.4V (Insertion Loss) 40uA max 2.4 (Isolation) 300mA typ 100mA typ SMA(F) Removable Connectors Size 1.5" x 2.0: x 0.4" Sealing Hermetic 245

246 100MHz to 40GHz, SP8T, High Isolation Switch P8T-100M40G-85-T FF Frequency Isolation Insertion Loss VSWR In/Out Operating Input Power Switching Speed DC Voltage and Current 0.1 to 40.0GHz >90dB (0.1 to 18GHz) >80dB (18 to 26.5GHz) >70dB typ. (26.5 to 40GHz) 10dB Max. 6dB typ. (0.1 to 18GHz 8dB typ. (18 to 26.5GHz) 10dB typ. (26.5 to 40GHz) 2.5:1 max. +20dBm CW max. 100nsec max. Measured 30nsec 180mA max, 67mA typ. 65mA Control Signal Connectors Finish 8-Bit TTL Individual Control 0 = Insertion Loss 1 - Isolation 2.92mm(F) Gold Plated Size 4.0" x 1.5" x 0.4" 246

247 PMI MODEL: P16T-100M20G-60-T-512-SFF SP16T, TERMINATED, SOLID STATE, PIN DIODE SWITCH Frequency 0.1 to 20.0GHz Single Pole 16 Throw 100 MHz TO 20 GHz Frequency Range 60dB Isolation 150nS On/Off Switching Speed Insertion Loss 8.5dB typ Isolation 60dB typ VSWR In/Out 2.0:1 VSWR Output/Off 2.0:1 Switching Speed Rise/Fall 15ns max Delay On/Off Input Power Survival Power Control Connectors Power Supply 150ns max +20dBm CW 1 Watt CW, 10 Watts Peak, 1 usec TTL Logic "0" = On "1" = Off SMA (F) Removable 750mA max 200mA max Size 8.0" x 3.0" x 0.65" Finish Gold Plated 247

248 PMI MODEL: P20T-4G8G-80-T-515-SFF SP20T, TERMINATED, SOLID STATE, PIN DIODE SWITCH PMI Model No. P20T-4G8G-80-T-515-SFF is an absorptive, single pole, twenty throw, pin diode switch that operates over the 4.0 to 8.0GHz, frequency range. This model incorporates a TTL compatible driver for easy system integration. Frequency Isolation Insertion Loss VSWR In/Out Operating Input Power RF Switching Speed DC Voltage Control Signal Connectors In/Out DC & Control Connectors Finish 4.0 to 8.0GHz 80dB min 4.0dB max 2.0:1 max, 1.8:1 typ 100mW max CW (Hot Switchable) 2usec max (50% TTL to 90% RF) 2usec max (10% RF to 90% RF) +5 VDC 300mA max +15VDC 200mA max 5-Bit Decoded TTL SMA(F) Solder Pins Painted Blue *Mounting surface to be free of paint 248

249 PMI MODEL: P20T-4G8G-80-T-515-SFF SP20T, TERMINATED, SOLID STATE, PIN DIODE SWITCH TYPICAL ISOLATION & VSWR 90dB Isolation 2.0:1 VSWR TYPICAL INSERTION LOSS & RETURN LOSS 4.0dB IL 249

250 PMI MODEL: P32T-0R5G18G-60-T-SFF SP32T, TERMINATED, SOLID STATE, PIN DIODE SWITCH Single Pole 32 Throw 500 MHz TO 18 GHz Frequency Range 60dB Isolation 100nS On/Off Switching Speed Frequency Insertion Loss Isolation VSWR In/Out Switching Speed Input Power Survival Power Control RF Connectors Control & Power DC Supply 0.5 to 18.0GHz 9.5dB max 60dB min (0.5 to 2.0GHz) 70dB min (2.0 to 18.0GHz) 2.0:1 max. 100ns max 20dBm CW max (Operating) 1 Watt CW, 10 Watts Peak, 1us 5-Bit Decoded TTL SMA(F) 9 Pin Sub D Male 1600mA 200mA Size 8.0" x 3.5" x 1.0" 250

251 PMI MODEL: P32T-0R5G18G-60-T-SFF SP32T, TERMINATED, SOLID STATE, PIN DIODE SWITCH J33-J1 Insertion Loss & Return Loss J33-J1 Isolation & Off Arm Termination Switching Speed: ON Delay (50Ns per Division) OFF Delay (50Ns per Division) 251

252 20 - SWITCH MATRICES 252

253 SOLID STATE SWITCH MATRIX Integration of SP8T, 20MHz to 3.0GHz Switch Matrix with Integrated Power Dividers FREQUENCY RANGE INSERTION LOSS ISOLATION VSWR INPUT 1dB Compression Point SWITCHING SPEED AMPLITUDE BALANCE MHz 3.0dB Typ. 55dB Typ. 2.0:1 Max. +25dB Typ. 10µS OFF / 20µS ON ±0.25dB PHASE BALANCE ±4.0º VIDEO TRANSIENTS DC POWER SUPPLY Above 20MHz = -100dBm Below 20MHz = -75dBm + 450mA 250mA 253

254 SOLID STATE SWITCH MATRICES 20MHz TO 40GHz, 4x4, 8x8, 16x16 or 32x32 Blocking and Non-Blocking Model Number Frequency Range (GHz) Number Of Inputs To Outputs Insertion Loss (db) Isolation (db) OIP3 (db) Switching Speed (nsec) VSWR Max. Input Power (dbm, CW) Chassis Size SM-20M3G-4X / :1 20 6U, 19" Chassis SM-20M3G-8X / :1 20 6U, 19" Chassis SM-20M3G-16X / :1 20 6U, 19" Chassis SM-20M3G-32X / :1 20 6U, 19" Chassis SM-2G18G-4X / :1 20 6U, 19" Chassis SM-2G18G-8X / :1 20 6U, 19" Chassis SM-2G18G-16X / :1 20 6U, 19" Chassis SM-2G18G-32X / :1 20 6U, 19" Chassis SM-18G40G-4X / :1 20 6U, 19" Chassis SM-18G40G-8X / :1 20 6U, 19" Chassis SM-18G40G-16X / :1 20 6U, 19" Chassis SM-18G40G-32X / :1 20 6U, 19" Chassis 254

255 SOLID STATE SWITCH MATRICES 20MHz TO 40GHz, 4x4, 8x8, 16x16 or 32x32 Blocking and Non-Blocking Switch Matrix Block Diagram 255

256 21 - SWITCH FILTER BANKS 256

257 8 TO 26.5GHz, 2 CHANNEL, SWITCH FILTER BANK PMI MODEL No: 2SFB-8G26G-CD-SFF Rev C Pass-Band Frequency Range Insertion Loss Flatness Isolation of RF Input from Power and Control Outputs VSWR 8.62 to 8.70GHz 5.5dB max 1.0dB max Peak-Peak 50dB min (Between 8.0 and 26.5GHz) 2.0:1 max across frequency range FULL PULSE Green Trace: TTL Signal Yellow Trace: RF Signal Group Delay Reject Band Frequency Range Rejection Bypass Frequency Range Insertion Loss Flatness VSWR Connectors RF Input/Output RF Input/Output coupling Input RF Power Level ( No Damage) Input IP3 (pin = -10dBm, DeltaF = 2MHz) Switching Speed Voltage Logic Input 1ns max (goal) to 17.4GHz 20dB min 8.0 to 26.5GHz 5.0dB max within ±2.0dB of max passband I.L. 1.0dB max Peak-Peak over each 100MMHz segment s.0:1 max across frequency range SMA(F) removable AC coupled +20dBm CW max (powered and unpowered) +27dBm max, +32dBm typ 100ns max +5V ± 100mA max TTL/ CMOS +5V Compatible Size 1.5" x 0.8" x 0.5" 257

258 2 TO 18GHz, 4 CHANNEL, SWITCH FILTER BANK PMI MODEL: 4SFB-2G18G-CD-SFF 4-Way Switch Filter Bank Low Harmonic Distortion 0.5 Watt RF Power Handling PARAMETERS FREQUENCY RANGE INSERTION LOSS ISOLATION PASS BAND OVERLAP POWER HANDLING VIDEO FEED THRU LOW END REJECTION FILTER A PASS BAND 50 dbc Stop Band 50 dbc Stop Band FILTER B PASS BAND 50 dbc Stop Band 50 dbc Stop Band FILTER C PASS BAND 50 dbc Stop Band 50 dbc Stop Band SPECIFICATIONS 2.0 TO 18.0 GHz 7.0dB Max 60dBc Min 10 MHz Min 50 MHz Max +27dBm Min -65dBm 1MHz BW, 0.4 to 18.0 GHz 24dB/Octave in all four channels GHz GHz DC 0.4 GHz GHz GHz DC 0.4 GHz GHz GHz DC 0.4 GHz Using Interdigital Filters FILTER D PASS BAND HARMONICS PASS BAND VSWR DC POWER SUPPLY SWITCHING SPEED GHz -65dBc Min 2.0:1 Max +100mA / -50mA 500nS Max On/Off 258

259 1 to 18 GHz, 6 CHANNEL, INTEGRATED, DOUBLE SIDED, SWITCH FILTER BANK PMI MODEL No: 6SFB-CC-100M18G-MAH-RX-TX RECEIVE SIDE FILTER BANK TRANSMIT-SIDE FILTER BANK Frequency Range Gain Isolation Switching Speed Inputs J1 Input: Frequency Power Level J6 Input Outputs Frequency Power Level J3 Output: Frequency Power Level Thru Channel Passband Number of Filter Channels Channel 1 Center Frequency 3dB Bandwidth Rejection Channel 2 Center Frequency 3dB Bandwidth Rejection Channel 3 Center Frequency 3dB Bandwidth Rejection Channel 4 Center Frequency 3dB Bandwidth Rejection Channel 5 Center Frequency 3dB Bandwidth Rejection Control Logic Power Connectors Digital/Power Connector 100MHz to 18.0GHz 6dB Typ J1, J6 100dB 100ns J1, J6 Input from Backplane 100MHz to 18.0GHz -80 dbm to -10 dbm Output to Transceiver 100Mhz to 18.0GHz -52 dbm to -22 dbm J3 Output to Transceiver 100MHz to 18.0GHz -74 dbm to -4dBm typ 100MHz to 18.0GHz 5 Channels 3400MHz 2000MHz -40 dbc (100MHz to 2GHz) -40dBc (4.8 to 8.5GHz) 5400MHz 2000MHz -40 dbc (100MHz to 4GHz) -40 dbc (6.8 to 13.5GHz) 7400MHz 2000MHz -40 dbc (100MHz to 6GHz) -40 dbc (8.8 to 18GHz) 9400MHz 2000MHz -40 dbc (100MHz to 8GHz) -40 dbc (10.8 to 18GHz) 11400MHz 2000MHz -40 dbc (100MHz to 10GHz) -40 dbc (12.8 to 18GHz) 3.3V TTL +12V, -12V, +5V, +3.3V SMA (F) 15PIN Micro-D Mating Connector Provided Size 4.925" x 3.68" x 0,35" Finish Painted Gray Operating Temperature -40ºC to +85 ºC 259

260 950MHz to 18 GHz, 8 CHANNEL, SWITCH FILTER BANK PMI MODEL No: 8SFB-950M18G-CD-SFF Channel 8 Thru Path Number of Filter Channels 8 Channels Channel 1 Specifications: Channel 1Passband Frequency 0.95 to 6.05GHz Channel 1 High Side Rejection 6.9 to 18.0GHz Channel 2 Specifications: Channel 2 Passband Frequency 5.15 to 8.25GHz Channel 2 Low Side Rejection DC to 4.3GHz Channel 2 High Side Rejection 9.0 to 18.0GHz Channel 3 Specifications: Channel 3 Passband Frequency 7.35 to Channel 3 Low Side Rejection DC to 6.5GHz Channel 3 High Side Rejection 11.3GHz 12.5 to 18.0GHz Channel 4 Specifications: Channel 4 Passband Frequency 9.85 to 13.15GHz Channel 4 Low Side Rejection DC to 9.2GHz Channel 4 High Side Rejection 13.8 to 18.0GHz Channel 5 Specifications: Channel 5 Passband Frequency to 15.65GHz Channel 5 Low Side Rejection DC to 11.5GHz Channel 5 High Side Rejection 16.2 to 18.0GHz Channel 6 Specifications: Channel 6 Passband Frequency to 16.45GHz Channel 6 Low Side Rejection DC to 14.0GHz Channel 6 High Side Rejection 16.8 to 18.0GHz Channel 7 Specifications: Channel 7 Passband Frequency to 18.05GHz Channel 7 Low Side Rejection DC to 14.0GHz Channel 7 High Side Rejection Not Specified Channel 8 Specifications: Channel 8 Passband Frequency Pass Through to 18.05GHz Common Specifications: Insertion Loss 9.0dB Typ. (All passbands equalized to within 3dB) VSWR 2.0:1 max. Impedance 50 Ohms Switching Speed 60nsec Typical, 100nsec max. Control 3 Line Decoded TTL Power Supply +15VDC max. -15VDC max. Connectors SMA(F) Size 4.33"L x 5.10"W x 0.98"H Finish Painted Gray 260

261 950MHz to 18 GHz, 8 CHANNEL, SWITCH FILTER BANK PMI MODEL No: 8SFB-950M18G-CD-SFF Switching Speed OFF Delay 100Ns/Div. FULL PULSE 200nS/Div. 261

262 22 - THRESHOLD DETECTORS 262

263 PMI MODEL: GMTA-1002 HIGH SPEED THRESHOLD DETECTOR PARAMETERS SPECIFIED VALUE TEST RESULTS FREQUENCY RANGE 2.0 to 18.0 GHz 2.0 to 18.0 GHz THRESHOLD LEVEL Pin = -18 TO C dbm RESPONSE TTL I / TTL O INPUT VSWR DC POWER SUPPLY NO RF SIGNAL 100 µs max 11us 2.5 : Pin =-10 dbm 2.216:1 50 ma 41 ma THRESHOLD SETTING STABILITY +/- 3 db MAX OVER FREQUENCY TEMPERATURE FREQ. 2 GHz 4 GHz 6 GHz 8 GHz 10 GHz 12 GHz 14 GHz 16 GHz 18 GHz 25 C 0 C 85 C

264 PMI MODEL: TD-6G18G-CD-SFF HIGH SPEED THRESHOLD DETECTOR PMI Model No. TD-6G18G-CD-SFF is a high speed threshold detector designed to operate over the 6.0 to 18.0GHz frequency range with an adjustable threshold level of -30 to +10dBm and a VSWR of 3.0:1 max. The unit is supplied with removable SMA female connectors in a compact housing that measures 1.0" x 0.6" x 0.19". Frequency Dynamic Range -Setting -Pulse Signal Flatness Propagation Delay Output Recovery Time (Or Pulse Stretching) 6.0GHz to 18.0GHz -30 to -10dBm -26 to +10dBm +/-1.5dB max 20nsec typ, 30nsec max TTL Compatible 150 nsec max -20dBm or Lower 3.0:1 max Power Supply +/-12 or +/-15 Volts, Resistive Setting is Optional Connectors In/Out SMA(F) Size 1.0" x 0.6" x 0.19" Finish Gold Plated 264

265 PMI MODEL: TD-6G18G-CD-SFF HIGH SPEED THRESHOLD DETECTOR Propagation Delay nS VSWR 2.846:1 265

266 2MHz to 18.0GHz Threshold Detector CDT-2M18-30-BB-DE-D Frequency Range to 18.0GHz VSWR 1.9:1 Maximum Thru Path Insertion Loss 2.5dB Maximum Power Range Operational: -30 to 0dBm (10kHz, Video Bandwidth) Output Polarity Positive RF Connectors SMA RF Damage Level +28dBm Minimum ON 502nS OFF 1.24µS Threshold Level 0 to 2.5VDC Detected Output 0 to 2.5VDC DC Power Supply +V mA DC Power Supply -V mA Size 2.5" x 2.90" x 0.50" Weight 3 Ounces Typical 266

267 2MHz to 18.0GHz Threshold Detector CDT-2M18-30-BB-DE-D Video Output (mv) vs. Power Input (dbm) Thru Path Insertion loss & Return Loss 267

268 100MHz to 10.0GHz Threshold Detector PMI MODEL No: TDC-30T-0110-CD-1 PARAMETERS Frequency Range: Insertion Gain: SPECIFIED VALUE 0.1 to 10 GHz 8 db Nominal VSWR: 2.0:1 Frequency Flatness: ±1.5 db Typ, ±2.0 db Max Threshold Level: Threshold Variation: Propagation Delay: Adjustable ±0.5 db Typical over any 1 GHz 20 ns Max, 15 ns Typ Output Pulse Width When Input: -20 dbm to -10 dbm Within 10 ns of Input Pulse Width -10 dbm to +0 dbm Within 10 ns of Input Pulse Width -10 dbm to +10 dbm Within 25 ns of Input Pulse Width -20 dbm to +10 dbm Within 25 ns of Input Pulse Width Power Supply: ma Max ma Max 268

269 100MHz to 10.0GHz Threshold Detector PMI MODEL No: TDC-30T-0110-CD-1 PROPAGATION DELAY YELLOW = INPUT GREEN = OUTPUT 269

270 1GHz to 12GHz Threshold Detector PMI MODEL: TD-1G12G-RL-CD-SFF Frequency VSWR Dynamic Range Threshold Variation (With Frequency) Propagation Delay Minimum Pulse Width Output 1.0 to 12.0GHz min 3.0:1 typ -30dBm to -10dBm +/-1.5dB max 10ns typ, 3dB above threshold setting (50% RF Input to 50% Logic at -10dBm) 50ns typ TTL "0" Input Power > Threshold Setting TTL "1" Otherwise Temperature Stability Threshold Setting Control Threshold Level Setting Range Input Power Power Supply Connectors RF Output Threshold Adjust 1.0dB typ 3dB Above Threshold Setting External Voltage 0 to +5V -30 to -10dBm 100mW CW max 100mA typ Removable SMA(F) Removable SMA(F) Solder Pin Size 1.1" 0.6" 0.19" Finish Gold Plated Propagation Delay Full Pulse 270

271 1GHz to 12GHz Threshold Detector PMI MODEL: TD-1G12G-RL-CD-SFF ON DELAY OFF DELAY VSWR PLOT 271

272 23 - USB PRODUCTS 272

273 PMI MODEL: P2T-500M40G-USB 500MHz TO 40GHz, 60dB Isolation, Absorptive, USB Switch Features: Low Insertion Loss High isolation USB 2.0 Controlled Ultra-Broad Band Operation Frequency Isolation Insertion Loss VSWR In/Out Input Power Survival Power Connectors In/Out Power and Control Connector 0.5 to 40.0GHz 60dB min. 6.0dB max. 2.5:1 max. +20dBm CW max 1 Watt Peak, 1usec 2.92mm(F) USB Type A Plug Size 2.25" x 1.0" x 0.33" Finish Driverless Installation No External Power Supplies Painted Gray Simply run the PMI provided application from any Windows computer *Tested for compatibility on Windows XP and Windows 7 Powered through USB 273

274 PMI MODEL: P2T-500M40G-USB 500MHz TO 40GHz, 60dB Isolation, Absorptive, USB Switch Insertion & Return Loss J1 J2 PMI GUI Interface Rise Time Insertion & Return Loss J1 J3 Fall Time 274

275 PMI MODEL: AMP-12-50M40G-USB 50MHz TO 40GHz, 12dB Gain, Low Noise, USB Amplifier Features: Low Noise Excellent Gain Flatness Ultra-Broadband Operation USB 2.0 Controlled Frequency Gain Gain Flatness VSWR In/Out 0.05 to 18.0GHz 12dB typical ±2.5dB typical 2.3:1 typical OP1dB +10dBm typical Noise Figure 4.5dB Typical DC Supply USB 2.0 Connectors SMA(F) Finish Epoxy Paint Gray Size 2.25" x 1.0" x 0.33" 275

276 PMI MODEL: AMP-12-50M40G-USB 50MHz TO 40GHz, 12dB Gain, Low Noise, USB Amplifier Gain & Return Loss 276

277 PMI MODEL: ANT M40G-USB 100MHz TO 40GHz, 30dB Attenuation, USB Attenuator Features: Low Loss 30dB Dynamic Range Ultra-Broad Band Operation USB 2.0 Controlled Frequency Attenuation Range Insertion Loss VSWR In/Out Attenuation Accuracy Attenuation Step Size Connectors Power Connector 0.1 to 40.0GHz 30dB 5dB Typical up to 20GHz 8dB Typical up to 40GHz 2.5:1 typical ±2.5dB Typical 1dB 2.92mm (F) USB type A plug Size 2.25" x 1.0" x 0.33" Finish Driverless Instalation No External Power Supplies Painted Gray Simply run through the PMI provided application from any windows computer *Tested for compatibility on Windows XP and Windows 7 Powered through USB 277

278 PMI MODEL: ANT M40G-USB 100MHz TO 40GHz, 30dB Attenuation, USB Attenuator Insertion & Return Loss 30dB Attenuation 278