Modula CAT-5/RGBHV Enclosure

Transcription

1

2 Modula CAT-5/RGBHV Enclosure This Boards & Specifications section contains specific board installation information for boards contained in the following Modula enclosure model: Modula Enclosure Model x32 Enclosure Your custom built enclosure(s) contains one or more of the boards listed below. If an enclosure is not ordered fully packed (with a total of 64 I/O connectors), any of these boards may be added to expand its capabilities. Modula Boards CAT-5/RGBHV (Chapter 1) Input Receiver, 25 ft. (7.62 m) from transmitter Receiver, 100 ft. (30.48 m) from transmitter Receiver, 200 ft. (60.96 m) from transmitter Receiver, 300 ft. (91.44 m) from transmitter Output Transmitter Modula Boards & Specifications

3 Modula CAT-5/RGBHV Enclosure Appendix A RGBHV over CAT-5 Transmitters & Receivers CAT-5 Transmitters & Receivers (Appendix A)* AF Transmitter Receiver (25 ft.) Receiver (100 ft.) Receiver (200 ft.) Receiver (300 ft.) Module Transmitter Receiver (25 ft.) Receiver (100 ft.) Receiver (200 ft.) Receiver (300 ft.) *Also see the RGBHV over CAT-5 Boards Installation Guide included with RGBHV CAT-5 Transmitters & Receivers. Modula Boards & Specifications

4 CAT-5/RGBHV CAT-5/RGBHV Applicability Notice This chapter pertains to the following CAT-5/RGBHV boards: Input boards , , , Output board Figure 1: CAT-5/RGBHV boards Each Modula CAT-5/RGBHV enclosure is built to hold up to sixteen CAT-5/RGBHV boards with four RJ-45 modular jacks each in a 32x32 configuration. Nine input and output combinations are possible: 32x32, 4x60, 8x56, 12x52, 16x48, 60x4, 56x8, 52x12, and 48x16, as well as subsets of these configurations (for example, 12x4 or 8x36). Modula Boards & Specifications 1-1

5 CAT-5/RGBHV CAT-5/RGBHV 1.1 Attaching Cables When attaching HD-15 cables, refer to the sheet labeled AutoPatch Modula Connector Guide found inside the back cover of this binder. The sheet shows where to attach each cable (use CAT-5, CAT-5e, or CAT-6). Follow the sheet exactly; the system was programmed at the factory to operate only as indicated on the sheet. To attach the connector cables, insert the modular plugs into the appropriate input and output modular jacks (see Figure 2). Figure 2: Insert modular plugs into modular jacks A Modula containing CAT-5/RGBHV boards must be connected to RGBHV over CAT-5 transmitter-to-matrix-to-receiver boards in either an AutoPatch AF-10 or Module, or a combination of the two (see the combinations list in Figure 3). A transmitter board connects each source to the enclosure and a receiver board connects the enclosure to each destination. See the RGBHV over CAT-5 Boards insert included with AF-10s or Modules for more information. Each cabled set allows up to 300 ft. to maintain minimal specifications. Total distance must be <400 ft. Figure 3: Equipment set up using RGBHV over CAT-5/UTP Transmitters and Receivers 1-2 Modula Boards & Specifications

6 CAT-5/RGBHV Configuration Files 1.2 CAT-5/RGBHV Configuration Files X N Connect (the graphical configuration software program on the CD shipped with the Modula) supports Modula systems with CAT-5/RGBHV connectors. CAT-5/RGBHV Note: Use this software only if you need to change the configuration information from the original specification. In a Modula CAT-5/RGBHV system, each matrix is a signal path. When you select a connector in the virtual matrix view, the properties box in the right pane indicates the four signals for each connector as appended numbers. For example, in Figure 4 the connector for input six contains the following four signal paths: Modula WB_IN_006.1 for the R signal path Modula WB_IN_006.2 for the G signal path Modula WB_IN_006.3 for the B signal path Modula S_IN_006.4 for the Sync or HV signal path Figure 4: Input Connector properties showing 4 signal paths for one CAT-5/RGBHV connector See Chapter 8 in the Installation & Setup section of this binder for information on managing configuration files with X N Connect. Modula Boards & Specifications 1-3

7 CAT-5/RGBHV CAT-5/RGBHV 1.3 Product Specifications CAT-5/RGBHV Boards Applies to receiver input boards (25 ft.), (100 ft.), (200 ft.), (300 ft.); transmitter output board General Resolution Support Power (modules) From VGA (640x480) to UXGA (1600x1200) over all distances <400 ft. ( m) 9 V DC, 500 ma wall transformer Transmitter / Receiver RGB Input / Output HV Sync Impedance +/-1 V TTL 75 ohms 1-4 Modula Boards & Specifications

8 RGBHV over CAT-5 Transmitters & Receivers The RGBHV over CAT-5 Transmitter and Receiver boards which are tuned for use with Modula Series Distribution Matrices are referred to as Transmitter-to-Matrix-to-Receiver boards. RGBHV over CAT-5 Trans. & Receivers Each AutoPatch RGBHV over CAT-5 Transmitter and Receiver board has a High Density DB-15 connector and an RJ-45 connector. They are available as either stand-alone modules (see Figure 5) or as AF-10 boards (see Figure 6). Figure 5: RGBHV over CAT-5 Transmitter and Receiver Modules Figure 6: RGBHV over CAT-5 boards in an AF-10 Transmitter boards pass RGBHV signals from source devices over CAT-5 cable (allowing RGBHV to be sent over longer distances). Receiver boards accept RGBHV signals from CAT-5 cable and pass them on to destination devices. Modula Boards & Specifications A-1

9 RGBHV over CAT-5 Transmitters & Receivers A.1 Attaching Cables The cable for the RJ-45 connector can be either CAT-5, CAT-5e, or CAT-6 cable. Note: A system using Transmitter-to-Matrix-to-Receiver boards (AF-10 and Module) is illustrated on page 1-2. RGBHV over CAT-5 Trans. & Receivers To attach connectors: Insert the connectors (as shown on an AF-10 Transmitter board in Figure 7). Figure 7: RGBHV over CAT-5 Transmitter board HD-15 Board Connector Pinout For High Density DB-15 board connector pinout information, see Figure Red 2. Green 3. Blue 4. ID Bit 5. GND N/C 6. Red GND 7. Green GND 8. Blue GND 9. No connect 10. Ground 11. ID Bit 12. ID Bit 13. Horizontal sync 14. Vertical sync 15. ID Bit Figure 8: HD-15 board connector pinout A-2 Modula Boards & Specifications

10 Product Specifications Note: If AutoPatch CAT-5 Transmitter or Receiver boards are inadvertently connected to the ports on an Ethernet hub, it will not have an adverse effect on the Ethernet network, nor will it cause damage to any of the equipment. A.2 Product Specifications Transmitter-to-Matrix-to-Receiver Boards Applies to: AF-10 transmitter board ; receiver boards (25 ft.), (100 ft.), (200 ft.), (300 ft.). Module transmitter 10-85; receivers (25 ft.), (100 ft.), (200 ft.), (300 ft.). RGBHV over CAT-5 Trans. & Receivers General Resolution Support Power (modules) From VGA (640x480) to UXGA (1600x1200) over all distances <400 ft. ( m) 9 V DC, 500 ma wall transformer Transmitter / Receiver RGB Input / Output HV Sync Impedance 1 Vpp TTL 75 ohms Modula Boards & Specifications A-3