GigE Vision Extended-Depth-of-Field Camera

Transcription

1 GigE Vision Extended-Depth-of-Field Camera EV-G030B1 (VGA, Monochrome) EV-G200C1 / EV-G200B1 (UXGA, Color /Monochrome) Product Specifications RICOH COMPANY, LTD. 1

2 Safety Precautions CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN! CAUTION: TO REDUCE TH E RISK OF EL ECTRIC SHOCK, DO N OT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. For U.S.A. Warning: This equipment generates and uses radio frequency energy and if not installed and used properly, I.e., in strict accordance with the instruction manual, may cause harmful interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. For Canada Warning: This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. Product Precautions Handle the camera with care. Do not abuse the camera. Avoid striking or shaking it. Improper handling or storage could damage the camera. Do not pull or damage the camera cable. During camera use, do not wrap he unit in any material. This will cause the internal temperature of the unit to increase. Do not expose the camera to moisture, or do not try to operate it in wet areas. Do not operate the camera beyond its temperature, humidity and power source ratings. While the camera is not being used, keep the lens or lens cap on the camera to prevent dust or contamination from getting in the CCD or filter area and scratching or damaging this area. Do not keep the camera under the following conditions: In wet, moist, and high humidity areas Under hot direct sunlight In high temperature areas Near an object that releases a strong magnetic or electric field Areas with strong vibrations Use a soft cloth to clean the camera. Use pressured air spray to clean the surface of the glass. DO not scratch the surface of the glass. 2

3 Index 1 SPECIFICATIONS Electronic specifications / Mechanical specifications / Environmental specifications EV-G030B Spectral Sensitivity Characteristics... 5 EV-G030B Electronic specifications / Mechanical specifications / Environmental specifications EV-G200C1/EV-G200B Spectral Sensitivity Characteristics... 7 EV-G200B EV-G200C1 (with IR cut filter) Operational temperature and the power consumption CONNECTOR SPECIFICATIONS RJ45 connector LED information Power/IO connector Input signal Output signals DC IRIS lens connector I/O CIRCUITS Input circuit Example circuit for the input signal Output circuit DIMENSIONS

4 1 Specifications 1.1 Electronic specifications / Mechanical specifications / Environmental specifications EV-G030B1 Product Electronic specifications Imager Total picture elements Active picture elements Chip size Cell size Scanning system Vertical frequency (Frame rate) Horizontal frequency Pixel frequency Noise level at 8bit output at 10bit output at 12bit output Minimum scene illumination Sync. System Video output Interface Protocol Exposure time ALC Gain Gamma AOI function Smear reduction Color interpolation White Balance function EV-G030B1 1/3" interline VGA monochrome progressive CCD: ICX424AL 692 (H) x 504 (V) VGA: 648 (H) x 494 (V) *EV-G003B1: With respect to the entered size, the 15 pixels above and below, and the 0 to 14th pixels and 633rd to 647th pixels on the left and right sides will be blacked out (H) x 4.89 (V) mm 7.4 (H) x 7.4 (V) µm Progressive Hz at full resolution to Hz changeable via the communication Maximum frame rate is depending on the AOI setting Maximum frame rate of the camera ( Hz) is 104 vertical resolution AOI setting khz MHz <= 3 Digit (Gain 0 db) <= 12 Digit (Gain 0 db) <= 48 Digit (Gain 0 db) 0.58 Lux at F1.2, Hz Internal Digital 8, 10 or 12 bit Raw data PoE : IEEE802.3af CLASS3 (1000BASE-T) GigE Vision 1.2 and GeniCam 2.0 compilant Preset continuous mode: 10 useconds to 16,777,216 useconds Preset trigger mode: 10 useconds to 16,777,216 useconds Pulse width mode: 10 useconds to Unlimited AGC (ON/OFF) 0 to 20.4 db Gamma 1.0 (Factory default) or downloadable gamma table Programmable AOI setting via the communication Selectable ON/OFF via communication Not available Not available Mechanical specifications Environmental specifications Trigger mode Communication I/O's Auto IRIS lens control Power Input voltage Consumption Dimensions Optical filter Optical center accuracy Material Lens mount Connectors Camera mount screws Weight Operational Lower limit temperature Higher limit Storage temperature Vibration Shock Standard compliancy RoHS Three opt isolated inputs and five opt isolated outputs Edge preset trigger, pulse width trigger (unlimited long exposure) UART communication through Ethernet port Not available to +26.4Vdc through power/io connector or Power Over Ethernet (Auto detection with power/io connector prioritized) Less than 6.5 W 50 (W) x 50 (H) x 53.5 (D) mm excluding connectors No filter Positional accuracy in H and V directions: +/- 0.3 mm Rotational accuracy of Ha nd V: +/- 1.5 deg. Aluminum (AC) C mount RJ45 connecor Power/IO connector: HR10A-10R-12PB (Hirose) or equivalent DC IRIS lens connector: M1951 (EMUDEN) or equivalent Two 1/4" Tripod screw holes (one each on top and bottom plate) Sixteen M4 screw holes (four each on top, bottom and both sides plate) Approximately 170 g Environmental temperature -5 deg. C Camera housing temperature (Top plate): 70 deg. C (Check "Operational temperature and power consumption") Environmental temperature -30 to 65 deg. C 20Hz to 200Hz to 20Hz (5min./cycle), acceleration 10G, 3 directions 30 min. each Acceleration 38G, half amplitude 6ms, 3 directions 3times each EMS: EN , EMI: EN55011 Group 1 Class A / FCC 47CFR Part 15 Subpart B Class A(Verification) / ICES-003(Class A) RoHS compliant 4

5 1.1.1 Spectral Sensitivity Characteristics EV-G030B Relative Response Wave length [nm] 5

6 1.2 Electronic specifications / Mechanical specifications / Environmental specifications EV-G200C1/EV-G200B1 Product EV-G200C1 EV-G200B1 Electronic Imager 1/1.8" interline UXGA color 1/1.8" interline UXGA monochrome specifications progressive CCD: ICX274AQ progressive CCD: ICX274AL Total picture elements 1688 (H) x 1246 (V) Active picture elements UXGA: 1624 (H) x 1236 (V) *EV-G200B1: With respect to the entered size, the 15 pixels above and below, and the 0 to 14th pixels and 1609th to 1623rd pixels on the left and right sides will be blacked out. *EV-G200C1: RAW data: With respect to the entered size, the 19 pixels above and below, and the 0 to 18th pixels and 1605th to 1623rd pixels on the left and right sides will be blacked out. RGb 8bit: With respect to the entered size, the 18 pixels above and below, and the 0 to 17th pixels and 1604th to 1623rd pixels on the left and right sides will be blacked out. Additionally, the 2 pixels above and below, the 18th,19th, 1602nd, and 1603rd pixels within the blackened area will be invalid (it is recommended that this area not be used for testing). Mechanical specifications Environmental specifications Chip size Cell size Scanning system Vertical frequency (Frame rate) Horizontal frequency Pixel frequency Noise level at 8bit output at 10bit output at 12bit output <= 3 Digit (Gain 0 db) <= 12 Digit (Gain 0 db) <= 48 Digit (Gain 0 db) Minimum scene illumination 7.27 Lux at F1.2, Hz 0.16 Lux at F1.2, Hz Sync. System Internal Video output Digital 8, 10 or 12 bit Raw or RGB 8 bi Digital 8, 10 or 12 bit Raw data Interface Protocol Exposure time PoE : IEEE802.3af CLASS3 (1000BASE-T) GigE Vision 1.2 and GenICam 2.0 compliant Preset continuous mode: 10 useconds to 16,777,216 useconds ALC Gain Gamma AOI function Smear reduction Selectable ON/OFF via the communication Color interpolation Available on RGB output Not available White Balance function Auto, manual and push to set white balance Not available is available on both Raw data output and RGB output Trigger mode Communication I/O's Auto IRIS lens control Power Input voltage to +26.4Vdc through power/io connector or Power Over Ethernet (Auto detection with power/io connector prioritized) Consumption Less than 6.8 W Dimensions 50 (H) x 50 (W) x 53.5 (D) mm excluding connectors Optical filter IR cut filter on No filter Optical center accuracy Positional accuracy in H and V directions: +/- 0.3 mm Rotational accuracy of Ha nd V: +/- 1.5 deg. Material Lens mount Connectors Camera mount screws Weight Operational Storage temerature Vibration Shock Standard compliancy RoHS Lower limit Higher limit 8.5 (H) x 6.8 (V) mm 4.4 (H) x 4.4 (V) µm Progressive Hz at full resolution to Hz changeable via the communication Maximum frame rate is depending on the AOI setting Maximum frame rate of the camera ( Hz) is 230 vertical resolution AOI setting khz MHz Preset trigger mode: 10 useconds to 16,777,216 useconds Pulse width mode: 10 useconds to Unlimited Auto iris lens, electronic iris and AGC (ON/OFF) 0 to 20.4 db Gamma 1.0 (Factory default) or downloadable gamma table Programmable AOI setting via the communication Edge preset trigger, pulse width trigger (unlimited long exposure) UART communication through Ethernet port Three opt isolated inputs and five opt isolated outputs Not available Aluminum (AC) C mount RJ45 connecor Power/IO connector: HR10A-10R-12PB (Hirose) or equivalent DC IRIS lens connector: M1951 (EMUDEN) or equivalent Two 1/4" Tripod screw holes (one each on top and bottom plate) Sixteen M4 screw holes (four each on top, bottom and both sides plate) Approximately 170 g Environmental temperature -5 deg. C Camera housing temperature (Top plate): 70 deg. C (Check "Operational temperature and power consumption") Environmental temperature -30 to 65 deg. C 20Hz to 200Hz to 20Hz (5min./cycle), acceleration 10G, 3 directions 30 min. each Acceleration 38G, half amplitude 6ms, 3 directions 3times each EMS: EN , EMI: EN55011 Group 1 Class A / FCC 47CFR Part 15 Subpart B Class A(Verification) / ICES-003(Class A) RoHS compliant 6

7 1.2.1 Spectral Sensitivity Characteristics EV-G200B Relative Response Wave length [nm] EV-G200C1 (with IR cut filter) B G R Relative Response IR cut filter Wave length [nm] 7

8 1.3 Operational temperature The temperature of the camera, which is the temperature of the inside of the camera and the case temperature, will be change depending on the usage of the camera. Please use the this camera under below conditions: Operational temperature: Camera housing temperature (Top plate) is less than 70 deg. C When use this camera, please set up the camera proper way to radiate heat, which is the housing top plate temperature is less than 70 deg. C. The case heat management becomes keep the heat rating of the electronic components of the camera. Temperature measuring point at the housing top plate 8

9 2 Connector specifications 2.1 RJ45 connector Caution: This product is a PoE type. Apply power (+10.8 to 26.4Vdc) through the power/io connector when PoE is not supported. Note: Recommend to lock down the screw to the camera with 0.18 N m torque when connect the screw lock LAN cable to the camera Pin assignment Pin No. Signal name 1 TA+ 2 TA- 3 TB+ 4 TC+ 5 TC- 6 TB- 7 TD+ 8 TD- Note. Power supply connection comprise PoE (IEEE802.3af). 9

10 2.2 LED information Yellow LED Green LED Status Orange light ON Green light ON Power ON Orange light ON Green light blinking 1Gb transfering Light OFF Green light blinking 100Mb transfering Power ON the camera Green LED: Blinking 1Gb transferring Yellow LED: OFF, Green LED: Blinking 100Mb transferring NIC, HUB or LAN cable is not support 1Gb. Please use 1Gb supported NIC, HUB and LAN cable. Please check the NIC and HUB setting is 1Gb transferring when use with 1Gb supported NIC and HUB. When snapping of the CAT5e cable, possibility to change the transferring speed from 1Gb to 100Mb. Please change the CAT5e cable. 10

11 2.3 Power/IO connector Connector: HR10A-10R-12PB (Hirose) or equivalent. This connector is for DC power input and the input and output signals. Pin assignment No. Signal type IO direction Spec. Initial signal 1 POWER IN GND - GND - 2 POWER IN to 26.4Vdc - 3 OUT0_AUX_OP OUT Opt. Isolated FameTriggerWait out 4 OUT1_AUX_OP OUT Opt. Isolated ExposureActive out 5 OUT2_AUX_OP OUT Opt. Isolated Open 6 OUT3_AUX_OP OUT Opt. Isolated Open 7 OUT4_AUX_OP OUT Opt. Isolated Open 8 IN0_AUX_OP IN Opt. Isolated TRG In 9 IN1_AUX_OP IN Opt. Isolated Open 10 IN2_AUX_OP IN Opt. Isolated Open 11 IO VCC IN - IO VCC - +3 to +26.4Vdc 12 IO GND - IO GND - Refer Fig. 3 Fig. 1 12pin connector Note.1: All I/Os (Pin number 3 through 10) are user assignable. Note.2: DO NOT connect or disconnect the power/io connector while the power input though PoE. 11

12 2.3.1 Input signal TRG IN: Input the trigger signal High: Voltage of the IO VCC IN Low: Smaller than 0.4V Output signals Set the output signals from the power/io connector. The following six output signals are selectable with the software or communication. A) FrameTriggerWait The user can check the camera conditions, which are the camera expose and the image output processing by the trigger signal with this FrameTriggerWait signal. a) High status (Voltage of the IO VCC IN No processing by the trigger signal The camera accepts the trigger signal b) Low status (0V): The camera is expose and the image output processing by the trigger signal The camera default setting is the input trigger signal is INVALID while low status for this signal. When the exposure starts while the image output by next trigger signal, please change the camera setting (Device code: 00H, Command: 13H) to accept the trigger signal while the image output. The noise appears on the image when start exposure while the image output. In this case, please change the H reset for the exposure start mode (Device code: 00H, Command: 12H) to change the exposure start point to next HD timing. B) UserOutput The status of this UserOutput signal can change with the UserOutputValue. C) ExposureActive The user can check the exposure time with this ExposureActive signal. a) High status (Voltage of the IO VCC IN ): The camera is exposing b) Low status (0V): The camera is not expose D) TriggerAuxiliary This TriggerAuxiliary signal is the input trigger signal. E) TriggerInternal This TrigerInternal signal is the input trigger signal with the trigger delay time. F) SensorReadOut This SensorReadOut signal is the FVAL signal, which is the image output period of the time. G) StrobeSignal This StrobeSignal signal is the strobe control signal. 12

13 2.4 DC IRIS lens connector Not available for use with this camera. Pin assignment Pin No. Signal name 1 DAMP- 2 DAMP+ 3 DRIVE+ 4 DRIVE Fig. 2 DC IRIS lens connector 13

14 3 I/O circuits 3.1 Input circuit CAMERA CAM VCC IO VCC INPUT If Maximum consumption of If is 6 ma USER INPUT OPTO ISOLATOR SHARP:PC400J00000F Fig. 3 Input circuits Response timing USER INPUT Td Ts 90% INPUT 10% Tr Tf Response time IO_VCC 3.3[V] 5.0[V] 12[V] 24[V] Td 2.5[us] 2.8 [us] 3.0[us] 3.0[us] Tr 100[ns] 100[ns] 100 [ns] 100[ns] Ts 689[ns] 584[ns] 545[ns] 520[ns] Tf 11[ns] 11[ns] 11[ns] 11[ns] 14

15 3.1.1 Example circuit for the input signal CAMERA CAM VCC IO VCC INPUT If OPTO ISOLATOR SHARP:PC400J00000F USER INPUT IO GND CAMERA CAM VCC IO VCC INPUT If IO VCC USER INPUT OPTO ISOLATOR SHARP:PC400J00000F IO GND 15

16 3.2 Output circuit CAMERA IO VCC OUTPUT 10k Ohm USER OUTPUT OPTO ISOLATOR SHARP:PC354NJ0000F IO GND Fig. 4 Output circuits Response timing OUTPUT Td Ts 90% USER OUTPUT 10% Tr Tf Response time IO_VCC 3.3[V] 5.0[V] 12[V] 24[V] Td 29.6[us] 30.4 [us] 35.2[us] 28.4[us] Tr 67.5[us] 60.2[us] 42.3[us] 31.0[us] Ts 2.2[us] 2.2[us] 2.8[us] 2.8[us] Tf 3.1[us] 3.8[us] 6.9[us] 10.9[us] 16

17 4 Dimensions M4 depth 4 (Top and bottom plate) φ Tripod screw depth 5 (Top and bottom plate) 1"-32UNF (C Mount) Unit: mm 17

18 RICOH COMPANY, LTD. 18