4 Channel Security Hubs

Transcription

1 4 Channel Security Hubs Operating Instructions KD-4PUV Four Channel Passive Transceiver KD-4AUVRX Four Channel Active Receiver KD-4AUVRX & KD-4PUV are multi-channel video hubs that allow for the transmission or reception of Color or Black & White single-channel video signals up to 4,000 feet (KD-4AUVRX) or 2,600 feet (KD-4PUV) with standard, unshielded CAT5 cabling.

2 Page 2 Table of Contents KD-4AUVRX About KD-4AUVRX Installation and Operation Connections Power Connections Uses with Active Transmitters Uses with Passive Transceivers & Multi-Channel Receivers / Transceivers Distance Adjustment Settings Mechanical / Technical Specifications KD-4PUV About KD-4PUV Installation and Operation Connections Uses with Passive Multi-Channel Receivers Uses with Active Receivers & Active Multi-Channel Receivers Distance Adjustment Settings Mechanical / Technical Specifications Key Digital Security Products Compatibility Chart Important Product Warnings Safety Instructions How to Contact Key Digital Warranty Please read all instructions to insure safe operation of the product.

3 Page 1 KD-4AUVRX Four Channel Active Receiver Quick Setup Guide Step 1: Begin with all input/output devices turned off with power cables removed Step 2: Connect video source, cabling, and Power into Active or Passive Transmitter Baluns Step 3: Insert twisted pair wires into UTP In Phoenix Connector or UTP In RJ45 connector as instructed on chassis above RJ45 input. See Connections section. Step 4: Connect video display and/or DVR to Out of KD-4AUVRX Receiver Hub Step 5: Secure + and power wires into Phoenix Connector Power inputs Step 6: Make appropriate settings to Distance Adjustment dip switches. See Distance Adjustment Table section Step 7: Power on all input/output devices Security Cam Security Cam Security Cam Security Cam KD-AUVTX KD-AUVTX KD-AUVTX KD-AUVTX 4,000 KD-4AUVRX Monitor Monitor Monitor Monitor DVR DVR DVR DVR

4 Page 2 About KD-4AUVRX Receives real-time Color or Black & White video KD-AUVTX Extends video up to 4,000 ft using a standard CAT cable when used with an Active Transmitter (Key Digital Model KD-AUVTX). KD-4AUVRX extends video up to 2,600 ft when used with a Passive Transmitter Balun (Key Digital Models KD-PVB and KD-4PUV) Manual Distance Adjustment switches for optimum picture quality at any length run up to 4,000 ft. Built-in interference rejection enables wire bundling with other low-voltage lines Built-in surge protection, ground loop isolation, gain and loss control, and video detection Compatible with CAT5/CAT5e/CAT6/CAT7 cabling Works with generic power supplies, from DC/AC 9V to 12 V (not included) Installation and Operation Before permanently securing the unit for final installation of cabling behind walls or ceilings, test for proper operation of the unit and the cables in your system. Connections KD-4AUVRX features two input options for video reception; a RJ45 port labeled UTP In and a Phoenix Connector labeled UTP In. It is recommended that only one of the two options be utilized as the input. Phoenix Connector: Secure twisted pair wires into + and - of Phoenix Connector block by loosening screws, inserting twisted pairs, and tightening screws until connection is secured. If using shielded CAT cabling, you may insert shield into Pin 3 of Phoenix Connector. RJ45: Terminate the incoming twisted pair wires into your RJ45 connector in the following fashion:

5 Page 3 Pin Assignment for KD-4AUVRX Pin# Description Pair 1 + Pair 1 - Pair 2 + Pair 3 + Pair 3 - Pair 2 - Pair 4 + Pair 4 - Power Connections Secure + and power wires into Power inputs (Pin 1 and Pin 2) of Phoenix Connector in the same fashion as securing connections. Positive (+) and Negative (-) polarity can be inserted into any of the two Power inputs. Insert Ground wire into Pin 3 if desired. Uses with Active Transmitters KD-4AUVRX units can be coupled with Key Digital s KD-AUVTX Active Transmitter as part of a multi-camera CCTV system. Using the KD-4AUVRX with the KD-AUVTX Active Hub will provide quality video up to 4,000 ft. Uses with Passive Transceivers & Passive Multi-Channel Transceivers KD-AUVRX units can be coupled with a passive Transmitter/Transceiver (Key Digital model KD-PVB) or a passive Multi-Channel Transmitter/Transceiver (Key Digital model KD-4PUV) in your application. Coupling a Passive Transmitter/ Transceiver with the KD-AUVRX Active Receiver Balun will provide quality video up to 2,600 ft.

6 Page 4 Security Cam Security Cam Security Cam Security Cam KD-4PUV 4,000 KD-4AUVRX Monitor Monitor Monitor Monitor DVR DVR DVR DVR Distance Adjustment Settings Dip Switch Configurations: Configuration Distance Adjustments should be set identically on Transmit (KD-AUVTX) and Receiver (KD-4AUVRX) unit. All distances listed above correspond to the pairing of active Transmit Balun (KD-AUVTX) and Active Receive Balun (KD-4AUVRX).

7 Page 5 Mechanical / Technical Specifications Input Output Max. Signal Input / Output Level: Surge Protection Bandwidth Format Impedance Humidity Distance Equalization and Gain Adjustments S/N Ratio: 4 twisted pair from CAT5 line In on Phoenix type stripping and cramping connector or 1 CAT5 on RJ45 Connector 2 BNC connector for Composite 1Vpp with 75Ω at display side or Audio SPDIF or any other format of video, audio, RS-232 or IR signaling. Composite: 1.2Vpp on 75Ω terminated at display, DC coupling or Line Audio or TTL +5V for digital RS-232, IR signaling Renewable solid state surge protection. DC to 6 MHz NTSC, PAL, SECAM BNC side 75Ω unbalanced, UTP side 100Ω balanced 0% to 95% non condensing 4000 feet Active Tx with Active Rx Coupling, 2000 feet Passive Tx with Active Rx coupling Passive impedance matching and fixed equalization. Manual adjustment by dip switches for CAT5 cable length measurement up to 4000 ft 58 db RMS un-weighted; 65 db weighted Ground Isolation Ground connection available for STP or Ground loop removal Power Source: DC/AC 9-12V Dimensions: WxDxH: 7.5 x3.3 x 1.75 excluding BNC Weight: 2 lb Operating Temperature -14F to +120F Accessories: None

8 Page 6 KD-4PUV Four Channel Passive Transceiver Quick Setup Guide Step 1: Begin with all input/output devices turned off with power cables removed. Step 2: Connect video source and cabling to Transmitter/Receiver Baluns Step 3: Insert twisted pair wires into UTP In Phoenix Connector or UTP In RJ45 connector as instructed on chassis above RJ45 input. See Connections section. Step 4: Connect video source, display and/or DVR to Out of KD-4PUV Transceiver Hub Step 5: Power on all input/output devices. Security Cam Security Cam Security Cam Security Cam KD-PVB KD-PVB KD-PVB KD-PVB 1,300 KD-4PUV Monitor Monitor Monitor Monitor Security Cam Security Cam Security Cam Security Cam

9 Page 7 About KD-4PUV Transmits or Receives real-time Color or Black & White video Extends Black & White video up to 2,600 ft using a standard CAT cable when used with an Active Receiver (Key Digital models KD-AUVRX or KD-4AUVRX). Extends Black & White video up to 1,300 ft using a standard CAT cable when paired with a Passive Transmitter Balun (Key Digital models KD-PVB or KD-4PUV). Built-in interference rejection enables wire bundling with other low-voltage lines Compatible with CAT5/CAT5e/CAT6/CAT7 cabling Installation and Operation Before permanently securing the unit for final installation of cabling behind walls or ceilings, test for proper operation of the unit and the cables in your system. Connections KD-4PUV features two options for video reception; a RJ45 port labeled UTP In and a Phoenix Connector labeled UTP In. It is recommended that only one of the two options be utilized as the. Phoenix Connector: Secure twisted pair wires into + and - of Phoenix Connector block by loosening screws, inserting twisted pairs, and tightening screws until connection is secured. If using shielded CAT cabling, you may insert shield into Pin 3 of Phoenix Connector. RJ45: Terminate the incoming twisted pair wires into your RJ45 connector in the following fashion: Pin Assignment for KD-4AUVRX Pin# Description Pair 1 + Pair 1 - Pair 2 + Pair 3 + Pair 3 - Pair 2 - Pair 4 + Pair 4 -

10 KD-4PUV Page 8 Uses with Passive Multi-Channel Receivers Monitor Monitor Monitor KD-4PUV units can be paired with additional KD-4PUV 4-Channel Passive Receiver Hubs as part of a multi-camera CCTV system. Using the KD-4PUV with the KD-4PUV Passive Hub will provide equivalent distances as when coupled with other Key Digital Passive Transceiver Baluns; 1,300 feet. Security Cam Security Cam Security Cam Security Cam KD-4PUV 1,300 KD-4PUV Monitor Monitor Monitor Monitor Uses with Active Receivers & Active Multi-Channel Receivers KD-4PUV units can be used as a Transmitter and coupled with an Active Receiver (Key Digital model KD-AUVRX) or an Active Multi-Channel Receiver (Key Digital model KD-4AUVRX). Coupling a KD-4PUV 4-Channel Passive Transmitter with the KD-AUVRX Active Receiver Balun or KD-4AUVRX Active 4-Channel Receiver will provide quality video up to 2,600 ft. Note: The usage of a KD-4PUV balun to receive video signals from an Active Transmitter (Key Digital model KD-AUVTX) is not recommended. For best results in an active/passive coupling, it is recommended that the KD-4PUV Passive Balun be used as the Transmitter, while the KD-AUVRX or KD-4AUVRX Active Receiver Baluns be used as the Receiver.

11 Page 9 Mechanical / Technical Specifications Tx Input / Rx Output Tx Output / Rx Input Max. Signal Input / Output Level: Surge Protection Bandwidth Format Impedance Humidity Distance Equalization and Gain Adjustments S/N Ratio: 1 BNC connector for Composite 1Vpp with 75Ω at display side or Audio SPDIF or any other format of video, audio, RS-232 or IR signaling. 1 twisted pair from CAT5 line In on Phoenix type stripping and cramping connector or 1 CAT5 on RJ45 Connector Composite: 1.2Vpp on 75Ω terminated at display, DC coupling or Line Audio or TTL +5V for digital RS-232, IR signaling Renewable solid state surge protection. DC to 6 MHz NTSC, PAL, SECAM BNC side 75Ω unbalanced, UTP side 100Ω balanced 0% to 95% non condensing 4000 feet Active Tx with Active Rx Coupling, 2000 feet Passive Tx with Active Rx coupling Passive impedance matching and fixed equalization. Manual adjustment by dip switches for CAT5 cable length measurement up to 4000 ft 58 db RMS un-weighted; 65 db weighted Ground Isolation Ground connection available for STP or Ground loop removal Power Source: DC/AC 9-12V Dimensions: WxDxH: 7 x3.3 x 1.75 excluding BNC Weight: 2 lb Operating Temperature -14F to +120F Accessories: None

12 Page 10 Key Digital Security Products Compatibility Chart Tx Passive Transceiver Balun Active Balun 4-Channel Passive Transceiver Passive Transceiver Balun Active Receiver Balun Rx 4-Channel Passive Receiver 4-Channel Active Receiver Not Recommended 4000 Not Recommended Note: Distances listed apply to video extension only. Key Digital Model Numbers: Security Baluns Passive Transceiver Baluns KD-PVB (Passive Balun with ) KD-PVBVP (Passive Balun with and Power) KD-PVBVPD (Passive Balun with, Power, and Data) Active Baluns KD-AUVTX (Active Transmitter) KD-AUVRX (Active Receiver) Active/Passive 4-Channel Hubs KD-4PUV (Passive 4-Channel Transceiver) KD-4AUVRX (Active 4-Channel Receiver)

13 Page 11 Important Product Warnings: 1. Always test for proper operation of the unit before permanently securing to final location. 2. Connect all cables before providing power to the unit. Safety Instructions. Please be sure to follow these instructions for safe operation of your unit. 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Only use attachments/accessories specified by the manufacturer. 10. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

14 Page 12 How to Contact Key Digital System Design Group (SDG) For system design questions please contact us at: Phone: Key Digital Trainings For questions about Key Digital Trainings please contact us at: Phone: Customer Support For customer support questions please contact us at: Phone: Technical Support For technical questions about using Key Digital products, please contact us at: Phone: Marketing and Public Relations: For marketing and public relations information, please contact us at: Phone: Shipping For shipping questions please contact us at: Phone:

15 Page 13 Accounting: For accounting questions please contact us at: Phone: Repairs and Warranty Service Should your product require warranty service or repair, please obtain a Key Digital Return Material Authorization (RMA) number by contacting us at: Phone: Feedback rma@keydigital.com Please any comments/questions about the manual to: customersupport@keydigital.com Warranty All Key Digital products are built to high manufacturing standards and should provide years of trouble-free operation. They are backed by a limited two-year parts and labor warranty Key Digital, Inc. All rights reserved.

16 Key Digital, led by digital video pioneer Mike Tsinberg, develops and manufactures high quality, cutting-edge technology solutions for virtually all applications where high quality video imaging is important. Key Digital is at the forefront of the video industry for Home Theater Retailers, Custom Installers, System Integrators, Broadcasters, Manufacturers, and Consumers. We provide total video system solutions because we know and help drive the technology, the industry, the business, and all the latest up-and-coming standards. But most of all, we know exactly what you need for your unique application - the right solution. 521 East 3rd Street, Mount Vernon, NY Phone :: Fax :: Web :: Rev 0 Jan. 2010