USER MANUAL 2AMCV551VPBS

Transcription

1 USER MANUAL 2AMCV551VPBS SUBJECT INDEX: DESCRIPTION TECHNICAL SPECIFICATION FUNCTIONAL DESCRIPTION POWER SUPPLY AND DALI BUS WIRING DIAGRAM PUSH + BLUETOOTH MODE BLUETOOTH CONTROL Necto Group S.r.l Padova - Via Canada, 8 - ITALY - T F info@nectogroup.com pag. 1

2 DIMMER CONVERTITORE MONOCANALE DALI/PUSH BLUETOOTH IoT Light DALI/PUSH CONVERTER SINGLE CHANNEL DIMMER BLUETOOTH IoT Light CARATTERISTICHE TECNICHE TECHNICAL NOTES - Dimmer Mono canale con Uscita in Tensione PWM. - Range di alimentazione: 8-53V DC. - Uscita in Tensione PWM 8-53V DC con corrente da 0A a 12A (576W a 48V DC). - Controllabile tramite app Android/iOS Necto Group. - Ingressi di Controllo: Pulsante isolato x1, Bluetooth LE x1. - Uscite di sincronia: PWM x1, DALI x1. - Circuito Stampato UL. - Classe di protezione: IP20. - Dimensioni Standard 40x80x24.45 mm. - Dimensioni con Accessori 40x100x24.45 mm. - Protezione da inversione di polarità. - Protezione circuito aperto. - Protezione da picchi tensione. PULSANTE N/O ISOLATO N/O insulated switch - Mono channel Dimmers with Output Tension PWM. - Input Range: 8-53V DC. - Output Tension PWM 8-53V DC with current from 0A to 12A (576W at 48V DC). - Controllable with Android/iOS app Necto Group. - Input Controls: Insulated Push button x1, Bluetooth LE x1. - Output Sync: PWM x1, DALI x1. - Printed Circuit UL. - Protection Class: IP20. - Standard Dimension 40x80x24.45 mm. - Dimension with accessories 40x100x24.45 mm. - Reverse polarity protection. - Open circuit protection. - Surge voltage protection. - Dimension with accessories 40x100x24.45 mm. - Reverse polarity protection. - Open circuit protection. - Surge voltage protection. INGRESSI DI CONTROLLO - CONTROL INPUTS INSULATED PUSH BUTTON USCITA SYNCRO OUTPUT SYNCRO PWM X1 DALI X1 CORRENTE MAX IN USCITA (*) MAX OUTPUT CURRENT 12A Dimmer Mono canale con Uscita in Tensione PWM. Range di alimentazione: 8-53V DC. Uscita in Tensione PWM 8-53V DC con corrente da 0A a 12A (576W a 48V DC). Controllabile tramite app Android/iOS IOT LIGHT. Mono channel Dimmers with Output Tension PWM. Input Range: 8-53V DC. Output Tension PWM 8-53V DC with current from 0A to 12A (576W at 48V DC). Controllable with Android/iOS app IOT LIGHT. Necto Group S.r.l Padova - Via Canada, 8 - ITALY - T F info@nectogroup.com pag. 2

3 CODICE CODE TENSIONE IN INGRESSO INPUT VOLTAGE CORRENTE USCITA (MAX) (MAX) OUTPUT CURRENT n. CANALI IN USCITA n. OUTPUT CHANNELS POTENZA MAX IN USCITA MAX OUTPUT POWER INGRESSI DI CONTROLLO CONTROL INPUTS SCATOLA CASE DIM. DIM. 2AMCV551VPBS 8-53V DC 12A 1 576W a 48V DC Pulsante isolato x1 Bluetooth LE x1 SI 40x80 mm h 24,45 mm Necto Group S.r.l Padova - Via Canada, 8 - ITALY - T F info@nectogroup.com pag. 3

4 FUNCTIONAL DESCRIPTION 2AMCV551VPBS device allows the control of DALI compliant devices via PUSH interface and/or via Bluetooth Low Energy with Necto Group app. The 2AMCV551VPBS controls external devices by broadcasting DALI commands (DAPC), it is not necessary to configure DALI Addresses on controlled devices. POWER SUPPLY AND DALI BUS WIRING DIAGRAM POWER SUPPLY AND DALI BUS WIRING DIAGRAM 2AMCV551VPBS - FIGURE N. 1 The 2AMCV551VPBS dimmer has to be powered according to the polarity showed in FIG. 1 through the DC IN (+ and -) terminals. In case the power supply polarity is inverted no damage will be caused to the device. The LED (LED PWR) positioned on the circuit board indicates the presence of power supply. The LED (LED DIM) shows the dimming level of the output. The LED load connection is optional and has to be made by using the OUT (L+ CH1- ) terminals. Necto Group S.r.l Padova - Via Canada, 8 - ITALY - T F info@nectogroup.com pag. 4

5 PUSH + BLUETOOTH MODE In order to activate this mode of control/operation it is necessary connect the DALI bus between the DALI terminals and an N.O. PUSH button to PUSH terminals according to Figure 1 (DC voltage range:10 265V, AC Vac 50 65Hz). No polarization is needed for the input signal. The maximum current absorbed by the PUSH interface is about 2mA. PUSH input drive the intensity. The dimmer saves the output position in order to restore the set level in case of power failure (preset). PUSH interface operation Single Click (rapid press (<1sec)) - Turns on or off the output (ON/OFF). Double Click (rapid press (<1sec)) - Sets maximum brightness (output= 100%) Long Press (long press (>1sec)) - If the dimmer is in OFF position, it sets the output to the minimum value (default= 1%) - If the dimmer is in ON position, the long press enables the output dimming (up/down). The maximum current absorbed by the PUSH interface is about 2mA. Necto Group S.r.l Padova - Via Canada, 8 - ITALY - T F info@nectogroup.com pag. 5

6 BLUETOOTH CONTROL In order to activate this mode of control/operation it is necessary to install the Necto Group App on the Android or ios device that you want to use for the 2AMCV551VPBS dimmer control. The implemented features are: Switching on and off and the brightness level control of each individual light point. Ability to group together and control several light points with just a simple command. Creation and recall of your favourite lighting sceneries. The system management from a single simplified user interface. THE BLUETOOTH LE CONNECTION DOES NOT REQUIRE PAIRING PROCEDURE Necto Group App features (*depending on the device only some functions may be available) Dimmer management at 1 or 4 channels with different modes of operation: - Mono channel - 4 synchronized channels - RGB (3 channels or 3 zones) - RGB + White (4 channels or 4 zones) - Dynamic White Necto Group S.r.l Padova - Via Canada, 8 - ITALY - T F info@nectogroup.com pag. 6

7 In order to install the app on your Apple or Android device you need to scan the desired QRCode to be automatically redirected to the IoT Light application. As an alternative you can download the app by clicking on one of two links below: Apple: Android: Necto Group S.r.l Padova - Via Canada, 8 - ITALY - T F info@nectogroup.com pag. 7