USER MANUAL 2AMIN514VPBS

Transcription

1 USER MANUAL 2AMIN514VPBS SUBJECT INDEX: DESCRIPTION TECHNICAL SPECIFICATION PUSH OPERATION BLUETOOTH MODE + PUSH Necto Group S.r.l Padova - Via Canada, 8 - ITALY - T F info@nectogroup.com pag. 1

2 INTERFACCIA DIMMER BLUETOOTH IoT Light PS INTERFACE BLUETOOTH IoT Light USER MANUAL 2AMIN514VPBS CARATTERISTICHE TECNICHE TECHNICAL NOTES - Interfaccia digitale per il dimming di alimentatori AC/DC generici con ingresso di controllo PWM. - L interfaccia è dotata di un relè per il distacco del primario dell alimentatore AC/DC. - Range di alimentazione: V AC. - Controllabile tramite app Android/iOS IOT LIGHT. - Ingressi di Controllo: Pulsante isolato V AC x1, Bluetooth LE x1. - Uscite di sincronia: PWM x1. - Circuito Stampato UL. - Classe di protezione: IP20. - Dimensioni Standard 40x80x24.45 mm. - Dimensioni con Accessori 40x100x24.45 mm. - Protezione da inversione di polarità. - Protezione circuito aperto. - Protezione da picchi tensione. PULSANTE N/O ISOLATO N/O insulated switch - digital interface for dimming of generic AC/DC power supplies with PWM control input. - The interface is equipped with a relè system for galvanic separation between mains and AC/DC power supply primary circuit. - Input Range: V AC. - Controllable with Android/iOS app IOT LIGHT. - Input Controls: Insulated Push button V AC x1, Bluetooth LE x1. - Output Sync: PWM x1. - Printed Circuit UL. - Protection Class: IP20. - Standard Dimension 40x80x24.45 mm. - Dimension with accessories 40x100x24.45 mm. - Reverse polarity protection. - Open circuit protection. - Surge voltage protection. INGRESSI DI CONTROLLO - CONTROL INPUTS Pulsante isolato / Insulated Push button V AC x1 Bluetooth LE x1 USCITA SYNCRO OUTPUT SYNCRO PWM X1 CORRENTE MAX DI DISTACCO (*) MAX RELEASE CURRENT 5A Interfaccia digitale per il dimming di alimentatori AC/DC generici con ingresso di controllo PWM. L interfaccia è dotata di un relè per il distacco del primario dell alimentatore AC/DC. Range di alimentazione: V AC. Controllabile tramite app Android/iOS IOT LIGHT. Digital interface for dimming of generic AC/DC power supplies with PWM control input. The interface is equipped with a relè system for galvanic separation between mains and AC/DC power supply primary circuit. Input Range: V AC. Controllable with Android/iOS app IOT LIGHT. Necto Group S.r.l Padova - Via Canada, 8 - ITALY - T F info@nectogroup.com pag. 2

3 CODICE CODE TENSIONE IN INGRESSO INPUT VOLTAGE FREQUENZA PWM / CORRENTE MASSIMA PWM FREQ / MAX DRIVE CURRENT n. CANALI IN USCITA n. OUTPUT CHANNELS POTENZA MAX DI DISTACCO MAX RELEASE POWER INGRESSI DI CONTROLLO CONTROL INPUTS SCATOLA CASE DIM. DIM. 2AMIN514VPBS V AC 390Hz (20mA) 1 220AC Pulsante isolato / Insulated Push button V AC x1 BLUETOOTH LE x1 SI 40x80 mm h mm Necto Group S.r.l Padova - Via Canada, 8 - ITALY - T F info@nectogroup.com pag. 3

4 PUSH OPERATION WIRING DIAGRAM 2AMIN514VPBS - FIGURE N. 1 2AMIN514VPBS device can be driven by PUSH interface Figure n. 1 shows the electrical connections necessary to make the device operate. Connect the dimmable power supply input (primary power supply) to LOAD terminals and connect D+ and Dterminals to power supply dimming interface. Pay attention to the polarity. ATTENTION: THE DEVICE WORKS WITH MAINS VOLTAGE, IT IS RECOMMENDED TO FOLLOW CAREFULLY THE SAFETY PRECAUTIONS DURING INSTALLATION PUSH interface operation Single Click (rapid press (<1sec)) - Turns on or off the output (ON/OFF). Double Click (rapid press (<1sec)) - Sets maximum brightness (output= 100%) Long Press (long press (>1sec)) - If the dimmer is in OFF position, it sets the output to the minimum value (default= 1%) - If the dimmer is in ON position, the long press enables the output dimming (up/down). Necto Group S.r.l Padova - Via Canada, 8 - ITALY - T F info@nectogroup.com pag. 4

5 BLUETOOTH MODE + PUSH BLE 2AMIN514VPBS WIRING - FIGURE N. 2 In order to activate this mode of control/operation it is necessary to install the Necto Group App on the Android or ios device that you want to use for the 2AMIN514VPBS dimmer control and disconnect any 0-10V (1-10V) inputs or potentiometer connected to the dimmer. The implemented features are: Switching on and off and the brightness level control of each individual light point. Ability to group together and control several light points with just a simple command. Creation and recall of your favourite lighting sceneries. The system management from a single simplified user interface. THE BLUETOOTH LE CONNECTION DOES NOT REQUIRE PAIRING PROCEDURE Necto Group App features (*depending on the device only some functions may be available) Dimmer management at 1 or 4 channels with different modes of operation: - Mono channel - 4 synchronized channels - RGB (3 channels or 3 zones) - RGB + White (4 channels or 4 zones) - Dynamic White Necto Group S.r.l Padova - Via Canada, 8 - ITALY - T F info@nectogroup.com pag. 5

6 In order to install the app on your Apple or Android device you need to scan the desired QRCode to be automatically redirected to the IoT Light application. As an alternative you can download the app by clicking on one of two links below: Apple: Android: Necto Group S.r.l Padova - Via Canada, 8 - ITALY - T F info@nectogroup.com pag. 6