ARVUNID2 ARVUNID2 0-10V ARVUNID2 INSTALLATION INSTRUCTIONS. Inputs. 12 Vdc 24 Vdc Controllers LED

Size: px

Start display at page:

Download "ARVUNID2 ARVUNID2 0-10V ARVUNID2 INSTALLATION INSTRUCTIONS. Inputs. 12 Vdc 24 Vdc Controllers LED"

Emil Reed
5 years ago
Views:

1 Made in Italy INSTALLATION INSTRUCTIONS Power supply units and control gear -V +D rev. //2 Inputs 2 Vdc 24 Vdc Controllers NO push button Potentiometer V -V DMX52/RDM IN Pot -V -V IN LED DMX52 >RDM< Outputs (constant voltage) max W (x5a 2 Vdc) max 2 W (4x4A 2 Vdc) max W (x5a 24 Vdc) max 4 W (4x4A 24 Vdc) Ch Vdc [RGB+W] Max 5A/ch (@ch) Max 4A/ch (@4ch) V out INITIAL OPERATING SETTINGS SET USING ROTARY SWITCHES (hundreds, tens, units) address assignment and personality using RDM; <-> 52 DMX address and personality selection using RDM; 5 <-> 5 Not valid (address assignment and personality using RDM, as if it were ); > up Special functions (starting on p. ). <-> 2 Special functions: Hundreds Tens function code; Units number of inputs controlled or function parameter: L&L Luce&Light / Via della Tecnica, 42 / Povolaro di Dueville, Vicenza / Italy / T / F /2

2 CONNECTING DEVICES TO SECONDARY CIRCUIT (CONSTANT VOLTAGE) The 4 outputs of the secondary circuit work at constant voltage ( V out ); as a consequence, LED lighting devices can be connected that also work at constant voltage. Multiple devices can be connected to the same output by connecting the devices in parallel. Connection in parallel using 4 channels Example: RGB+White device Ch- To calculate the maximum number of devices that can be connected to a single output, check the operating voltage of each individual device (Vf app ), take into consideration the number of devices and total up the individual powers involved P tot. P tot P app + P app It holds that: P tot < Pmax where is the power supply voltage of the Vdc For example, if 4 channels are used, we shall have: [max 4 2Vdc] [max 24Vdc] Tot max 2W Tot max 4W Connection in parallel using channels Example: RGB device Connection in parallel using 2 channels Example: dynamic white device Ch- Ch Vdc 2-24 Vdc For example, if channels are used, we shall have: [max 2Vdc] Tot max W [max 2 24Vdc] Tot max W For example, if 2 channels are used, we shall have: [max 2Vdc] Tot max 2W [max 2 24Vdc] Tot max 24W L&L Luce&Light / Via della Tecnica, 42 / Povolaro di Dueville, Vicenza / Italy / T / F /2

3 OPERATING SETTINGS USING NO PUSH BUTTONS 2 4 * 4 * (Selector switch settings) IN When powered off, the last mode selected is stored. 4-4: input on terminal, controls channels simultaneously. : short press on/off; long press when powered on (> sec) UP and DOWN dimming; 42: 2 inputs on terminals and : : controls dimming through channels +2; : controls dimming through channels +4; 4: inputs on terminals, and IN : : controls dimming through channel ; : controls dimming through channel 2; IN : controls dimming through channels +4; +IN: controls dimming through channel 4; -5: RGB sequencer : short press on/off; double-click when powered off % on; long press when powered on (> sec) UP and DOWN dimming; long press when powered off (> sec) % on; : short press colour cycle on/off; long press when powered off (> sec) cycle time selection based on strobe frequency: sec (fastest strobe), sec, min, min (slowest strobe); IN : short press colour saturation (white) on/off; long press when powered off (> sec) saturation change; long press when powered on (> sec) minimum saturation; -: RGB-W sequencer : short press on/off; double-click when powered off % on; long press when powered on (> sec) UP and DOWN dimming; long press when powered off (> sec) % on; : short press colour cycle on/off; long press when powered off (> sec) cycle time selection based on strobe frequency: sec (fastest strobe), sec, min, min (slowest strobe); IN : short press colour saturation (white) on/off; long press when powered off (> sec) saturation change; long press when powered on (> sec) minimum saturation; : Dynamic white : short press on/off; long press (> sec) UP and DOWN dimming; : long press (> sec) mixing channels +2 and +4; 2: Dimmer on/off % on channels in parallel : short press on/off; double-click when powered off % on; long press when powered on (> sec) UP and DOWN dimming on channels +2++4; long press when powered off (> sec) % on, on channels +2++4; : on/off on 4 channels : short press on/off on channels simultaneously; L&L Luce&Light / Via della Tecnica, 42 / Povolaro di Dueville, Vicenza / Italy / T / F /2

4 OPERATING SETTINGS USING ROTARY SWITCHES 2 * (Selector switch settings) * The rotary switches can be used to manage the controller in stand-alone mode; after the desired functions have been selected, power up the system to perform the perform the chosen light show. The settings may also be altered when the system is active. The available functions are given below: : Fixed colour yellow : Fixed colour cyan 2: Fixed colour green : Fixed colour magenta 4: Fixed colour red 5: Fixed colour blue : Fixed colour acquamarine : Fixed colour salmon pink : Fixed colour white from RGB (uses channels +2+) : Fixed colour white from RGB-W (uses channels +2++4) : Fixed colour white from W (use channel 4) : Stand-alone RGB-W speed sequence (uses channels +2++4) 2: Stand-alone cold colours sequence : Stand-alone warm colours sequence 4: Stand-alone RGB sequence (uses channels +2+) 5: Stand-alone RGB-W speed 2 (uses channels +2++4) : Stand-alone RGB speed 2 (uses channels +2+) : Stand-alone RGB-W speed (uses channels +2++4) : Stand-alone RGB-W speed 4 (uses channels +2++4) : Stand-alone RGB speed (uses channels +2+) 2: Stand-alone RGB pure colours speed 4 sequence (uses channels +2+) With the selector switches between and 2, two push buttons can be used to control pre-set light shows: - a short press on button switches the device on if it is off; - a short press on button plays the light shows one after the other, if the device is on; - a long press on button switches the device off; - a long press on button 2 dims the lighting. L&L Luce&Light / Via della Tecnica, 42 / Povolaro di Dueville, Vicenza / Italy / T / F /2

5 OPERATING SETTINGS USING KOHM POTENTIOMETER / V / V 2 * (Selector switch settings) * Control using V signal : input on terminal, controls channels simultaneously -V (between and ): dimming between V (off) and V (%); 2: 2 inputs on terminals and : -V (between and ): controls dimming through channels +2; -V (between and ): controls dimming through channels +4; V V V V : inputs on terminals, and IN : -V (between and ): controls dimming through channel ; -V (between and ): controls dimming through channel 2; -V (between and IN ): controls dimming through channels +4; IN Control using V signal : input on terminal, controls channels simultaneously -V (between and ): dimming between V (off) and V (%); 2: 2 inputs on terminals and : -V (between and ): controls dimming through channels +2; -V (between and ): controls dimming through channels +4; V V V V : inputs on terminals, and IN : -V (between and ): controls dimming through channel ; -V (between and ): controls dimming through channel 2; -V (between and IN ): controls dimming through channels +4; IN Control using Kohm entiometer 2: input on terminal, controls channels simultaneously Kohm (between and ): dimming between % and %; 22: 2 inputs on terminals and : Kohm (between and ): controls dimming through channels +2; Kohm (between and ): controls dimming through channels +4; 2: inputs on terminals, and IN : Kohm (between and ): controls dimming through channel ; Kohm (between and ): controls dimming through channel 2; Kohm (between and IN ): controls dimming through channels +4; IN L&L Luce&Light / Via della Tecnica, 42 / Povolaro di Dueville, Vicenza / Italy / T / F /2

6 OPERATING SETTINGS USING DMX52 SIGL DMX (Selector switch settings for DMX start address) DMX52 (Input) <- max 2m -> shielded twisted pair cable: 2x.5 max 2 (unit) 2 Ohm (terminator,25w) Ch- Ch- Ch- IN IN IN 2-24 Vdc Control using DMX52 signal <->52: DMX start address selection; 4 addresses are used in total (for example, if is set, the DMX addresses, 4, 5 and will be occupied) 5<->5: invalid. L&L Luce&Light / Via della Tecnica, 42 / Povolaro di Dueville, Vicenza / Italy / T / F /2

7 OPERATING SETTINGS USING DMX52 RDM SIGL 2 RDM DMX52 >RDM< (Selector switch settings) DMX52 RDM <- max 2m -> shielded twisted pair cable: 2x.5 max 2 (unit) 2 Ohm (terminator,25w) Ch- Ch- Ch- IN IN IN 2-24Vdc Control using DMX52 signal with RDM functionality : signal input on terminals DMX-, DMX+ and, address assignment using RDM. Personality selection using RDM. 5<->5: invalid. L&L Luce&Light / Via della Tecnica, 42 / Povolaro di Dueville, Vicenza / Italy / T / F /2

8 Personality: - Dimmer (synchronised outputs) - 2 Shutter (synchronised outputs) - RGBW speedy ST (red, green, blue, white, sync, strobe, delay) - 4 RGB (red, green, blue) - 5 RGB+dimmer (red, green, blue, dimmer) - RGBW (red, green, blue, white) - RGBW+dimmer (red, green, blue, white, dimmer) - RGBW (red, green, blue, white) - RGBW speedy ST (red, green, blue, white, sync, strobe, delay) - RGBW speedy ST (red, green, blue, white, sync, strobe, delay) gamma curve - RGBW (red, green, blue, white, sync, strobe, delay, dimmer) - 2 RGBW (red, green, blue, white, strobe, dimm. CTC fade freq.) - RGBW + freq. - 4 RGBW input V or push button (4 channels) - 5 RGBW input V or push button (4 channels) - RGBW entiometer + push button - RGBW entiometer RDM RDMPROG: DMX RDM programmer This is a USB-DMX/RDM interface patible with the E.2 RDM and DMX USITT standards. It is powered directly from the USB port on the PC and is not affected by problems with different electrical entials between the DMX line and the PC, even if it is disconnected and reconnected while in use: the built-in software immediately restores all the functions. RDMPROG allows bi-directional munication with RDM equipment over the DMX cable. The programmer has control software that uses the RDM protocol to recognise the lighting fixtures connected to the DMX; it is also possible to assign a DMX address in RDM mode by keying it into the corresponding program window. L&L Luce&Light / Via della Tecnica, 42 / Povolaro di Dueville, Vicenza / Italy / T / F /2

9 MASTER / SLAVE CONNECTION WITH -CHANNEL RGB FUNCTION (Selector setting in the Master controller) (Selector setting in all Slave controllers) Input <- max 2m -> shielded twisted pair cable: 2x.5 max 2 (unit) 2 Ohm (terminator,25w) Ch- Ch- Ch- IN IN IN Master Slave Slave 2-24 Vdc Other input types V V V V V V V V IN IN IN L&L Luce&Light / Via della Tecnica, 42 / Povolaro di Dueville, Vicenza / Italy / T / F /2

10 MASTER / SLAVE CONNECTION WITH DIMMER FUNCTION ON CHANNELS, 2, AND (Selector setting in the Master controller) (Selector setting in all Slave controllers) Input <- max 2m -> shielded twisted pair cable: 2x.5 max 2 (unit) 2 Ohm (terminator,25w) Ch- Ch- Ch- IN IN IN Master Slave Slave 2-24 Vdc L&L Luce&Light / Via della Tecnica, 42 / Povolaro di Dueville, Vicenza / Italy / T / F /2

11 MASTER / SLAVE CONNECTION WITH DYMIC WHITE FUNCTION 2 2 (Selector setting in the Master controller) (Selector setting in all Slave controllers) Input <- max 2m -> shielded twisted pair cable: 2x.5 max 2 (unit) 2 Ohm (terminator,25w) Ch- Ch- Ch- IN IN IN Master Slave Slave 2-24 Vdc L&L Luce&Light / Via della Tecnica, 42 / Povolaro di Dueville, Vicenza / Italy / T / F /2

12 L&L Luce&Light Via della Tecnica, 42 Povolaro di Dueville, Vicenza / Italy T / F

FEATURES MECHANICAL SPECIFICATIONS ELECTRICAL SPECIFICATIONS PRODUCT INTERFACE

FEATURES MECHANICAL SPECIFICATIONS ELECTRICAL SPECIFICATIONS PRODUCT INTERFACE DMX512 Wire Leads Input / Output FilmGrade DMX512 LED Dimmer / Decoder is a professional DMX512 dimmer and decoder that boasts the best dimming performance in the industry. The devices takes a low-voltage