Inputs/Outputs dimmer outputs 700W 2 inputs 0-10V or 1-10V for emergency operation or standalone operation
|
|
- Blanche Mills
- 6 years ago
- Views:
Transcription
1 Technical specifications / user manual Universal dimmer General The universal dimmer is suited for usage with high voltage lamps, magnetic transformers, electric transformers, ESL and LED retrofit lamps. There are 2 separate dimmer channels available, which are resistant to up to 700W respectively. By configuring and using a parallel circuit the dimmer is resistant to up to x400w. Each channel is adjustable to be used for the desired load (leading or trailing edge phase control). The dimmer will automatically check if the connected load is able to be used with the current setting after connecting it to operating voltage. By using a dim resolution of 6 bit, the dimmer meets highest requirements. Properties such as dim curves, minimum and maximum limits are factory defined, but can be changed and optimized by the operator. ISYGLT operators can adjust settings in the ProgrammDesigner software as usual. Free software is available for standalone or DMX usage. It allows adjusting parameters and displaying internal stats such as temperatures, voltages, peak currents and outputs via USB or RS-485 connection. Additionally, a new oscilloscope feature is integrated, which allows the operator for the first time to display the current load without dangerous measurements of line voltage. This also makes it possible to check unknown lamps such as new retrofit lights without any additional equipment. You only need a connected dimmer, a USB cable (USB type A to micro B m/m) and our free software. Inputs/Outputs dimmer outputs 700W 2 inputs 0-0V or -0V for emergency operation or standalone operation Device design black plastic case, can be put on 35mm DI bar 6 TE Display in ISYGLT operating mode LED status Meaning x LED (red) OFF no operating voltage O operating voltage, no errors consistent flashing operating voltage too high (>400Vs) flash 3x no valid ISYGLT parameters found x LED (yellow) OFF no BUS signal detected operating voltage / O BUS signal detected, own address not detected BUS consistent flashing BUS signal and own address detected 2 x LED (green) OFF output OFF, no errors O output O, no errors consistent flashing temperature too high flash x load too high flash 2x voltage too high flash 3x communication to dim processor failed Marktstrasse 57, Bad Toelz, GERMAY info@seebacher.de Fax: / 77772
2 Display in standalone and DMX operating mode LED status Meaning x LED (red) OFF no operating voltage O operating voltage, no errors Hz flashing operating voltage too high (>400Vs) flash x + pause,5s error at self test flash 2x + pause,5s no valid ISYGLT protocol detected in ISYGLT mode (DIP switch) flash 3x + pause,5s no valid parameters found x LED (yellow) OFF no BUS signal detected operating voltage / BUS O BUS is active, but no data received by communication processor DMX: o data transferred for desired address (telegram too short) or wrong data format RS-485 test: desired address or data format is wrong Hz flashing data received by communication processor 2 x LED (green) OFF output OFF, no errors O Hz flashing output O, no errors warning/shutdown at too high temperatures: communication processor: 65 C / 75 C MOSFET case: 95 C / 05 C flash x + pause,5s overload alert:. exceeding maximum peak current (>5A) 2. reaching the limit for power loss (>8W/channel) or peak current (>0A) flash 2x + pause,5s alert after shutdown at stress peaks >450V flash 3x + pause,5s communication to dim processor failed DIP switches ISYGLT BUS operating mode mode O ISYGLT PC test (RS485/USB) all OFF O sample adress 37 OFF 6 Adressbit adress 0 to Marktstrasse 57, Bad Toelz, GERMAY info@seebacher.de Fax: / 77772
3 DIP switches DMX-52 operating mode mode channel +2 coupled 8 7 sample DMX start adress 33 6 Adressbit O O A B C D adress 0 to 5 = 2=0 DMX-52 8Bit = 2= DMX-52 6Bit channel +2 seperated DIP switches standalone mode mode input -0V channel +2 coupled button dimmer input -0V O O input 0-0V A B C D reserve channel +2 seperated analog 0()-0V input 0-0V A reserve B C D Dim channel or ch.+2 coupled Dim channel 2 Marktstrasse 57, Bad Toelz, GERMAY info@seebacher.de Fax: / 77772
4 Operation when using DMX-52 and standalone with DIP switches A to D DIP A DIP B Operation OFF OFF automatic change of operation, the start value can be defined in the PC software on the General settings tab O OFF PAB phase control section/ OFF O PA phase control ingate/trailing edge O O ondim DIP C DIP D Setting dim characteristic such as minimum and maximum values, curves etc. (see PC software for ) OFF OFF Parameter of st column ( General settings in PC software ) O OFF Parameter of 2nd column ( General settings in PC software ) OFF O Parameter of 3rd column ( General settings in PC software ) O O Parameter of 4th column (with setting for preheating for ESL; General settings in PC software ) Technical specifications Type Article o Power supply 230V / 45 to 65 Hz Fuse protection x 230V circuit breaker or GL fuse 0A Output 2 x 230V short circuit safe, per channel Power loss <0,5...6W (standby...full load) per channel - total 2W at 2x700W Load Please provide sufficient ventilation of the switch cabinet or case (0)-0V sink current at -0V = 0,54mA source current at hardware option 0-0V = 0.4mA to 7kOhm Isolation voltage 3500V (ISYGLT-BUS / etwork) Short circuit prevention Electrical overload prevention by measuring current Short circuit shutdown within 0ms Subnet (RS-485) max. 5.6V limit because of Z diodes Weight 300g Connection Plug in screw terminals Operating temperature -0 C to +45 C -> at +50 C max. 60% connectable power -> at +55 C max. 50% connectable power -> at +60 C max. 30% connectable power Storing temperature -25 C to +70 C Humidity 0-85% relative humidity, not condensing IP code IP30 Appliance class I CE yes Marktstrasse 57, Bad Toelz, GERMAY info@seebacher.de Fax: / 77772
5 Pin assignment 9 pin plug (left) Terminal Internal connections Meaning GD ground for voltage inputs (0-0V) and BUS RS-485 UE control voltage input for dim output LD (emergency function) UE2 control voltage input for dim output LD (emergency function) SL - open SL2 - open SLC + open GD ground for voltage inputs (0-0V) and BUS RS-485 A ISYGLT subnet BUS RS-485 B ISYGLT subnet BUS RS pin plug (right) Terminal Internal connections Meaning LD dimmer load output V /VA leading/trailing edge LD2 dimmer 2 load output V /VA leading/trailing edge L line voltage 230V (45Hz-65Hz) neutral conductor neutral conductor neutral conductor View Marktstrasse 57, Bad Toelz, GERMAY info@seebacher.de Fax: / 77772
6 Oscilloscope function Example: Oscillogram of retrofit LEDs at phase control Marktstrasse 57, Bad Toelz, GERMAY Fax: / 77772
7 Wiring diagram ISYGLT 2x700W Sample: controlled by ISYGLT 2x700W B6A +24V 0V= BUS-A BUS-B L GD BUS A BUS B 005 O e.g. ISYGLT-Adr.5 OFF ISYGLT Art.-r.: RLC D LD max. 2x700VA LD2 UE UE2 GD +0V D2 0V optional: external voltage control e.g. emergency function 0()-0V 0()-0V channel channel 2 low voltage magnetic transformer trailing edge low voltage electronic transformer / dimmable ECG Suited for high voltage halogen Marktstrasse 57, Bad Toelz, GERMAY info@seebacher.de Fax: / 77772
8 Wiring diagram ISYGLT x400w Sample: controlled by ISYGLT x400w B6A +24V 0V= BUS-A BUS-B L GD BUS A BUS B 005 O e.g. ISYGLT-Adr.5 OFF ISYGLT Art.-r.: RLC D LD max. 2x700VA LD2 UE UE2 GD +0V D2 0V optional: external voltage control e.g. emergency function 0()-0V channel low voltage magnetic transformer trailing edge low voltage electronic transformer / dimmable ECG Suited for high voltage halogen Marktstrasse 57, Bad Toelz, GERMAY info@seebacher.de Fax: / 77772
9 Wiring diagram DMX-52 8/6 bit Sample: controlled by DMX52 8-/6-Bit DMX-I B6A COM DMX- DMX+ L GD BUS A BUS B 26 O e.g. 8 Bit DMX start adr.26 OFF ISYGLT for more DIP switch options please use the datasheet Art.-r.: RLC D LD max. 2x700VA LD2 UE UE2 GD +0V D2 0V optional: external voltage control e.g. emergency function 0()-0V 0()-0V channel channel 2 low voltage magnetic transformer trailing edge low voltage electronic transformer / dimmable ECG Suited for high voltage halogen Marktstrasse 57, Bad Toelz, GERMAY info@seebacher.de Fax: / 77772
10 Wiring diagram -0V und -button dimming Sample: -0V and -button dimming B6A L GD BUS A BUS B O OFF ISYGLT DIP switches please use the datasheet Art.-r.: max. 2x700VA LD LD2 UE UE2 GD RLC +0V D D2-0V Poti -0V Poti low voltage magnetic transformer option -0V potentiometer trailing edge Suited for low voltage electronic transformer / dimmable ECG high voltage halogen Option -button dimmer Marktstrasse 57, Bad Toelz, GERMAY info@seebacher.de Fax: / 77772
11 Wiring diagram potentiometer 0kOhm Sample: Potentiometer 0kOhm B6A L GD BUS A BUS B O OFF ISYGLT DIP switches please use the datasheet Art.-r.: max. 2x700VA LD LD2 UE UE2 GD RLC +0V D D2 S A E 0kOhm S A E 0kOhm low voltage magnetic transformer option potentiometer 0kOhm trailing edge Suited for low voltage electronic transformer / dimmable ECG high voltage halogen Marktstrasse 57, Bad Toelz, GERMAY info@seebacher.de Fax: / 77772
12 Safety instructions Responsibilities Caution!! Installation and montage of the module and the system is only allowed to a skilled electrician. The installer of the device bears responsibility for operator protection and responsibility for damage of property and the necessary information to the operator. Moreover he is responsible for compliance of the prevailing safety instructions of work and safety instruction for work on electric medium voltage installations. Residual endangernment range Residual endangerment potential by touching of medium voltage leading connections. At intended purpose of this ISYGLT module all authoritative standards and rules to avoid damages to persons or to properties are observed. A residual endangerment by voltage leading connections could not be excluded.. Warranty We guarantee within the German legal requirements. These relate to the exchange of the ISYGLT-module. Please send us the module back to the below mentioned business address and add a description of the failure. For all damages to persons and properties as a result of wrong connection, faulty operation and/or improper application of the module, we will assume no liability. Marktstrasse 57, Bad Toelz, GERMAY info@seebacher.de Fax: / 77772
Universal dimmer 6.3.1
Universal dimmer 6.3.1 UD-500-M2/B UD-500-M2/BP General The universal dimmer is suitable for all current dimmable illuminant types. There are two separate ate dimmer outputs which can each carry a load
More informationSmart-house Dimmer Power dimmer up to 500W Type SH2D500W230
Smart-house Dimmer Power dimmer up to 500W Type SH2D500W230 Universal dimmer switch for R, L, C up to 500W and LED loads Automatic load detection for L, R, C loads Integrated heat sink for temperature
More informationLED control gear Compact dimming. Uconverter LCBI 10 W 180/350/500 ma phase-cut/1 10 V lp BASIC series
Uconverter CBI W 1/3/ ma phase-cut/1 V lp BASIC series Product description Dimmable built-in ED Driver Constant current Output current 1, 3 or ma Max. output power W ominal life-time up to, h SEV Dimmable
More informationDocumentation. Content. Measurement and Control. Type: ELT-GP1. 1. Installation instructions 2. Data sheets 3. Declarations of conformity
Documentation Measurement and Control Type: ELT-GP1 Content 1. Installation instructions 2. Data sheets 3. Declarations of conformity (Part No. 008Q520) eltherm GmbH Ernst-Heinkel-Str. 6-10 57299 Burbach
More informationSmart Dupline Wireless dimmer with energy reading Type SHJWD200WExxx
Smart Dupline Wireless dimmer with energy reading Type SHJWD200WExxx Universal wireless dimmer up to 200 W for R, L, C load and LED lamps Wireless transmission based on IEE802.15.4 @ 2.4 GHz Automatic
More informationPowerPlex Compact Module PP-C-COM24
Description The PowerPlex Compact Module has been designed for the 12 V or 24 V DC-System of special vehicles, buses or boats. It provides inputs for switches and sensors as well as power outputs with
More informationCurrent Module, 3-channel, MDRC SM/S , GH Q R0111
, GH Q631 0034 R0111 SK 0086 B 99 Load and residual currents can be measured simultaneously using the current module. There are 3 isolated and independent measuring circuits available for this. The current
More informationDocumentation. Measurement and Control. Type: ELT-GP2
Documentation Measurement and Control Type: ELT-GP2 05.01.2018 K. Folkerts Content 1. Data sheet 2. Installation instructions 3. Declarations of conformity 05.01.2018 K. Folkerts 1 05.01.2018 K. Folkerts
More information1. Function. Universal dimming actuator REG-K/2x230/ 300 W. Universal dimming actuator REG-K/230/ 500 W. Universal dimming actuator REG-K/230/ 1000 W
L L N N on error RUN 1 2 3 4 KNX EIB 1 1 1 1 Chapter 9: Dimming actuators/control units Chapter 9:Dimming actuators/control unitsart. no.6493xxas of 10/079.2Universal dimming actuators Universal dimming
More informationRAIL MOUNTED NETWORK METER TYPE N27D USER S MANUAL
RAIL MOUNTED NETWORK METER TYPE N27D USER S MANUAL 1 Contents 1. Application... 5 2. meter set... 6 3. BASIC REQUIREMENTS, OPERATIONAL SAFETy... 6 4. installation... 10 4.1. Mounting... 10 4.2. External
More informationMU110-16R(K) Digital output module 16 channel. User guide
MU110-16R(K) Digital output module 16 channel User guide MU110-16R(K)_2016.12_0220_EN All rights reserved Subject to technical changes and misprints akytec GmbH Vahrenwalder Str. 269 A 30179 Hannover Germany
More informationOperating instruction
Operating instruction Radio Ref. no.: RAN..514.. RAN..914.. Table of contents 1. Safety notes... 3 2. Device overview... 4 2.1.Operating elements... 4 3. Function... 5 3.1.Intended use... 5 3.2.Product
More informationMV110-8AS. Analog input module 8 channel. User guide
MV110-8AS Analog input module 8 channel User guide MV110-8AS_2016.12_0226_EN All rights reserved Subject to technical changes and misprints Contents 1 Description... 2 1.1 Function... 2 1.2 RS485 network...
More informationPowerBar 4 Manual SAFETY NOTES WARNING! IMPORTANT:
PowerBar 4 Manual Thank you for purchasing this LITECRAFT product. For your own safety, please read the instruction manual carefully before turn on the product for the first time. SAFETY NOTES Each person
More informationRadio bus system Radio-universal dimming actuator, 1-gang. 1 Safety instructions. 2 Device components. Order-No. : Operating instructions
Order-No. : 1135 00 Operating instructions 1 Safety instructions Electrical equipment may only be installed and fitted by electrically skilled persons. Failure to observe the instructions may cause damage
More information02/11/2015
Modem communication plug and play solutions GSM Part number 88970119 For remote control of your application Automatic notification of alarms via SMS (GSM Modem) / email or on a PC with M3 ALARM software.
More informationLED control gear Compact fixed output. Uconverter LCI 50 W 1050 ma N020 TOP series Ø4,5. Ordering data
Product description 1-channel ED control gear Independent ED control gear for indoor use Output current and output voltage adjustable output input channel ominal life of 50,000 h (at ta max. with a failure
More informationLED converter Compact dimming. Uconverter LCAI 55 W 1400 ma O010 DALI ECO series Ø4,4. Ordering data
ED converter Product description 1-channel ED converter for indoor use Inbuilt converter for luminaires of protection class I Output current and output voltage adjustable FA output 12 V TC input channel
More informationLED Driver Compact dimming
Driver LCAI 35W 3mA 900mA ECO C flat ECO series Product description Dimmable built-in LED Driver for LED Constant current LED Driver Output current adjustable between 3 900 ma Max. output power 35 W Nominal
More informationPHASED OUT. LED Driver Linear / area dimming. Driver LCAI 20W 350mA 550mA ECO lp ECO series
Product description Dimmable built-in LED Driver for LED Constant current LED Driver Output current adjustable between 350 550 ma Max. output power 20 W Nominal life-time up to 100,000 h 5-year guarantee
More informationLED Driver Compact dimming
Driver LCA 1W 45mA phase-cut 22mm SR ADV ADVANCED series Product description Dimmable constant current LED driver (SELV) Independent driver with strain-relief housing Extra flat housing for constrained
More informationLED Driver Linear / area dimming. Udriver LCAI 20W 350mA 550mA ECO lp ECO series
Udriver LCAI 20W 350mA 550mA ECO lp ECO series Product description Dimmable built-in LED Driver for LED Constant current LED Driver Output current adjustable between 350 550 ma Max. output power 20 W Nominal
More informationSeries 7000 Torque Sensor for PTO-shafts
Properties PTO (Power Take-Off) shaft with integrated torque and angle measurement Non-contact measurement system, high robustness Special for PTO shafts 1 ¾ und 1 3/8 Plug & Play solution, no additional
More informationAT-SL-DDR & AT-SL-DDR-SA
AT-SL-DDR & AT-SL-DDR-SA Product Guide Slim-line RF DALI/DSI + relay controller Overview The AT-SL-DDR and AT-SL-DDR-SA are wireless controllers with two output channels capable of controlling incandescent,
More informationXDL-7DV1-48V5A. 7-in-1, Single Channel 240W Constant Voltage Dimmer. LED Controls supported. Applications. 7-in-1 Dimming LED Module
, Single Channel 240W Constant Voltage Dimmer The GRE Alpha dimmer provides full range 0-100%, smooth, high resolution dimming performance for constant voltage ED dimming applications. Flexible and easy-to
More informationPHASED OUT. LED Driver Linear / area dimming. Driver LCAI 20W 150mA 400mA ECO lp ECO series
EL Product description Dimmable built-in LED Driver for LED Constant current LED Driver Output current adjustable between 150 400 ma Max. output power 20 W Nominal life-time up to 100,000 h 5-year guarantee
More informationLMM31. Dimmer Micromodule, 1 load USER MANUAL 20410/ LMM31 ALL RIGHTS RESERVED MARMITEK
LMM31 Dimmer Micromodule, 1 load USER MANUAL 20410/20111019 LMM31 ALL RIGHTS RESERVED MARMITEK TABLE OF CONTENTS TABLE OF CONTENTS... 2 SAFETY WARNINGS... 3 HOW DOES MARMITEK X-10 WORK?... 4 ADRESSES...
More informationMaestro Local Lighting Controls
L O C A L L I G H T I N G C O N T R O L S Maestro local lighting controls, function like standard dimmers and switches, but can be controlled as part of the whole-house lighting control system. Local lighting
More informationDeltaSol AX HE * * Differential temperature controller Manual for the specialised craftsman
DeltaSol X HE Differtial temperature controller Manual for the specialised craftsman Installation Operation Functions and options Troubleshooting *110633* 110633 Thank you for buying this RESOL product.
More informationAT-SL-ADR & AT-SL-ADR/SA
AT-SL-ADR & AT-SL-ADR/SA RF 1-10V + relay controller Product Guide Overview The AT-SL-ADR and AT-SL-ADR/SA are wireless controllers with two output channels capable of controlling incandescent, fluorescent
More information4Q POWER AMPLIFIERS AC AND DC 3000VA 3x3000VA
PERFORMANCES High accuracy High stability Fast transients High inrush current facilities Wide bandwidth 25 khz at -3dB Internal waveform DC and up to 10 khz Very low distortion Quadrant change without
More informationDMX-CONTROL OF MOTORISED DIMMER SHUTTER AND LAMP IGNITION
RJ NET FOR COMPACT FOLLOWSPOT RANGE Manual 1149B SUPER KORRIGAN 1449B LUCY 1159B VICTOR 1459B FLO DMXCONTROL OF MOTORISED DIMMER SHUTTER AND LAMP IGNITION Product version : "LUCY" 1449 : V3 "SUPER KORRIGAN"
More informationEY-EM 522, 523: Remote I/O module, ecolink522, 523
Product data sheet 94.077 EY-EM 522, 523: Remote I/O module, ecolink522, 523 How energy efficiency is improved Regulation, control, monitoring and optimisation of operational systems, e.g. room automation
More informationAT-SL-DDR & AT-SL-DDR-SA
Product Guide AT-SL-DDR & AT-SL-DDR-SA Slim -line RF DALI/DSI + relay controller Overview The AT-SL-DDR andat-sl-ddr-sa are wireless controllers with two output channels capable of controlling incandescent,
More informationAC CURRENT GENERATOR POC-6000 (current from 0 to 1000 ARMS)
AC CURRENT GENERATOR PERFORMANCES Wide range of current 50 db dynamic range Signal-to-noise ratio: 80 db open loop protection Stability < 0,1% Very low THD distortion < 0,3% External synchronization Build-up
More information02/11/2015
"Compact" range with display CD12 Part number 88970041 Green LCD with 4 lines of 18 characters and configurable backlighting More cost effective solution Industrial temperature range (-20 C +55 C) Analogue
More informationJUMO dtrans T04 Four-wire Transmitter, settable via DIP switch/pc setup program
JUMO GmbH & Co. KG Delivery address:mackenrodtstraße 14, 36039 Fulda, Germany Postal address: 36035 Fulda, Germany Phone: +49 661 6003-0 Fax: +49 661 6003-607 e-mail: mail@jumo.net Internet: www.jumo.net
More informationThe universal input/output device is a DIN rail mounted device. It is connected to the EIB via a bus connecting terminal.
, GH Q631 0026 R0111 SK 0097 B97 The universal input/output device is a DIN rail mounted device. It is connected to the EIB via a bus connecting terminal. The device has 32 freely programmable inputs/outputs,
More informationSeries P. Applications
Ratings 25 800 VA Voltage Primary 230 / 400 / 460 V range Secondary 6 / 12 V 12 / 24 V 24 / 48 V 115 / 230 V Voltage selection by means of metal connection bridges, offering the full rated power at any
More informationDigital Proportional Amplifier. Type: RT-VSPA2-50. Series: 3X. Table of contents. Features. RD13763/11.07 Replaces:
Replaces: 09.12 Electro-hydraulic Control Digital Proportional Amplifier Type: RT-VSPA2-50 Series: 3X Table of contents Contents Page Features 1 Ordering code 2 Functional description 2 Block circuit diagram
More informationThis product is for use in a dry, indoor environment only. This product is not to be installed near water, liquid, or flammable materials.
The equipment described in this manual contains high voltage. Always disconnect power to the equipment before installing, disconnecting, or servicing the product. This product is for use in a dry, indoor
More informationThermocouple - Transducer
Thermocouple - Transducer TM3 Characteristics: Thermocouple type J, K, R, S, T, E, B, N Linearity error < 1% Measurement range configurable -210...+1820 C Built-in cold junction compensation Galvanic 3-way
More informationMILFORD INSTRUMENTS Limited
MILFORD INSTRUMENTS Limited DMX Receiver (#1-497) Rev1.5 09/01/2007 The DMX receiver module is designed to provide 8 consecutive channels of output from a standard DMX protocol input signal. The outputs
More informationFL ballasts Electronic dimming. PCA T8 EXCEL one4all lp Y II, W EXCEL T8
F ballasts E T8 PCA T8 EXCE oneall lp Y II, 18 58 W EXCE T8 Product description Processor-controlled ballast with y II inside Highest possible energy class CEMA EEI = A1 BAT 1 oise-free precise control
More informationDipl.-Ing. W. Bender GmbH & Co. KG Londorfer Str Grünberg Tel.: Fax:
Dipl.-Ing. W. Bender GmbH & Co. KG Londorfer Str. 65 35305 Grünberg Tel.: 06401 807-0 Fax: 06401 807-259 Insulation fault locator Insulation fault locator for DC IT systems with high system leakage capacitances
More informationPU202 Level converter & encoder signal generator without potential separation
Operating Manual PU202 Level converter & encoder signal generator without potential separation Product features: Converts HTL signals from 10 up to 30 V (A / B / Z) into the corresponding TTL / RS422 format
More informationLED Driver Compact dimming
Driver LCAI 35W 350mA 900mA ECO C ECO series Product description Dimmable built-in LED Driver for LED Constant current LED Driver Output current adjustable between 350 900 ma Max. output power 35 W Nominal
More informationTechnical description MT24. User manual WARNING GENERAL INSTRUCTIONS GENERAL DESCRIPTION
WARIG The equipment makes a compact set of the switchboard. Just this set is safe from the point of electrical shock. Therefore do not use other power supplies or circuits than mentioned in this direction
More informationISOSCAN EDS460-DG. Insulation fault locator for DC IT systems with high system leakage capacitances
ISOSCAN Insulation fault locator for DC IT systems with high system leakage capacitances _D00108_00_D_XXEN/05.2015 ISOSCAN Insulation fault locator for DC IT systems with high system leakage capacitances
More informationRadio Control Installation and Operating Instructions System 4
Radio Control Installation and Operating Instructions System 4 P.O. Box 403, One Cedar Parkway, Jackson, WI 53037 Phone: 800-628-1909 Fax: 262-677-2058 Revision: April 19, 2012 Contents Introduction 3
More informationCustom "Compact" range with display CD20 Custom Part number
Custom "Compact" range with display CD20 Custom Part number 88974051 "Modular" versions designed for Custom application-specific functions (Custom functions) LCD with 4 lines of 18 characters and configurable
More informationADC5000 SERIES. AC/DC Switch Mode Power Supplies and Rectifiers for Industrial and Telecom Applications. 60W, 125W and 250 W
ADC5000 SERIES AC/DC Switch Mode Power Supplies and Rectifiers for Industrial and Telecom Applications 60W, 125W and 250 W Input voltage 230/115 VAC voltages 12, 24, 36 or 48 VDC Statistical MTBF >3 000
More informationOTi DALI 80/ / CH OTi DALI 50/ / CH
www.osram.com OTi DALI 80/220-240/24 1-4 CH OTi DALI 50/220-240/24 1-4 CH 24 V DALI Constant Voltage LED driver Dimmable range 0% - 100% Benefits Slim form factor for mounting on the cove or in linear
More informationPHOENIX CONTACT - 09/2009
Electronic miniature circuit-breaker CLIPLINE Data sheet 03906_en_0 PHOENIX CONTACT - 09/2009 Description The EC-E... electronic miniature circuit-breaker selectively protects all 24 V DC load circuits
More informationPHASED OUT. LED Driver Compact dimming. Driver LCAI 55W 900mA 1750mA ECO C ECO series
Product description Dimmable built-in LED Driver for LED Constant current LED Driver Output current adjustable between 900 1,750 ma Max. output power 55 W Nominal life-time up to 100,000 h 5-year guarantee
More informationERV-M ELECTRONIC FAN SPEED CONTROLLER. Mounting and operating instructions
ELECTRONIC FAN SPEED CONTROLLER Mounting and operating instructions Table of contents SAFETY AND PRECAUTIONS 3 PRODUCT DESCRIPTION 4 ARTICLE CODES 4 INTENDED AREA OF USE 4 TECHNICAL DATA 4 STANDARDS 5
More informationTLS-A. Laurel Electronics, Inc. Triple output loop splitter. Connection details and general information
Laurel Electronics, Inc. 3183-G Airway Avenue, Costa Mesa, CA 92626 Tel 714 434-6131 Fax 714 434-3766 www.laurels.com Triple output loop splitter TLS-A Connection details and general information 1 2 3
More informationFL ballasts Electronic dimming. PCA T8 ECO lp Y II, W ECO T8
T8 PCA T8 ECO lp Y II, 18 58 W ECO T8 Product description Processor-controlled ballast with y II inside Highest possible energy class CELMA EEI = A1 BAT 1 Noise-free precise control via DALI or DSI signal,
More informationServomotor for butterfly valves VF, VFH. delta-elektrogas.com EE157-01/16
MZ Servomotor for butterfly valves VF, VFH delta-elektrogas.com EE157-01/16 MZ Servomotor Contents Description.... 2 Features........ 2 Functioning and application..... 3 Technical specifications......
More informationECM3 EARTH CONTINUITY RELAY
TECHNICAL DATASHEET ECM3 EARTH CONTINUITY RELAY Electrical Protection for Hard Rock Mines Application The ECM3 has been designed to provide earth continuity protection for cables containing pilot cores.
More informationBrunata Optuna H Ultrasonic energy meter Type 775 Installation Guide Edition 1.2
Ultrasonic energy meter Type 775 Installation Guide Edition 1.2 UK-QB101575 / 29.05.2012 Brunata a/s is a Danish owned company. We have more than 90 years of experience within developing and producing
More information02/11/2015
Modem communication plug and play solutions GSM Part number 88970119 For remote control of your application Automatic notification of alarms via SMS (GSM Modem) / email or on a PC with M3 ALARM software.
More information1 Safety instructions. 2 Device components. Radio bus system. Radio socket outlet adapter for dimming Order No. : Operating instructions
Order No. : 1185.. Operating instructions 1 Safety instructions Electrical equipment may only be installed and fitted by electrically skilled persons. Serious injuries, fire or property damage possible.
More informationCD770 DIGITAL MULTIMETER INSTRUCTION MANUAL
CD770 DIGITAL MULTIMETER INSTRUCTION MANUAL Table of Contents 1 SAFETY PRECAUTIONS Before use, read the following safety precautions.- 1-1 Explanation of Warning Symbols 001 1-2 Warning Messages for Safe
More informationLED Driver Linear / area dimming
EL Udriver LCAI 35W 900mA 1750mA ECO lp ECO series Product description Dimmable built-in LED Driver for LED Constant current LED Driver Output current adjustable between 900 1,750 ma Max. output power
More informationVoltage Adjustment. Load Regulation
HIGH DENSITY, CONFIGURABLE AC-DC POWER SUPPLY RCB1200 SERIES DS RCB1200 RE02 NOEMBER 2010 Description The RCB1200 is a modular, user configurable power supply offering unrivalled performances and flexibility.
More informationMU110-8R(K) Digital output module 8 channel. User guide
MU110-8R(K) Digital output module 8 channel User guide MU110-8R(K)_2019.01_0296_EN All rights reserved Subject to technical changes and misprints akytec GmbH Vahrenwalder Str. 269 A 30179 Hannover Germany
More informationSmart Power Relay E I...
Smart Power Relay E-48-8I... Description The Smart Power Relay E-48-8I.- is a remotely controllable electronic load disconnecting relay with three functions in a single unit: l electronic relay l electronic
More information8 Channel, DMX to 0 10 volt, Decoder board
8 Channel, DMX to 0 10 volt, Decoder board Allows DMX512 digital protocol to control analog devices that require a 0-10VDC control voltage. Upgrade 0-10 volt analog dimmers, use with motor controllers
More informationLED Driver Compact dimming outdoor
LED Driver Driver LCO W 350/500/700mA pc C ADV UNV ADVANCED outdoor series (UL certified) Product description Constant current LED Driver Dimmable via leading edge and trailing edge phase dimmers Dimming
More informationFL ballasts Electronic dimming. PCA T5 ECO lp Y, 3x14/24 W and 4x14/24 W ECO T5
T5 PCA T5 ECO lp Y, x1/ W and x1/ W ECO T5 Product description Processor-controlled ballast with y inside Highest possible energy class CELMA EEI = A1 BAT 1 Noise-free precise control via DSI signal, switchdim
More informationEY-EM 527: Remote I/O module, ecolink527
Product data sheet 94.078 EY-EM 527: Remote I/O module, ecolink527 How energy efficiency is improved Regulation, control, monitoring and optimisation of operational systems, e.g. room automation or HVAC
More informationAcuMesh Wireless RS485 Network. User's Manual SOLUTION
AcuMesh Wireless RS485 Network User's Manual AN SOLUTION ACUMESH - WIRELESS METERING SYSTEM COPYRIGHT 2015 V1.2 This manual may not be altered or reproduced in whole or in part by any means without the
More information(*) Reference the User Manual or contact the factory for parallel operation between modules plugged into slots 1/2/3/4 and slots 5/6/7/8.
HIGH DENSITY, CONFIGURABLE AC-DC POWER SUPPLY RCB1200 SERIES DS_RCB1200_RE04_OCTOBER 2015 DESCRIPTION The RCB1200 is a modular, configurable power supplies that provide high performance and outstanding
More informationPRODUCT LEAFLET AUGIER-BOX. Remote Monitoring Unit for Street Lighting /07/2011
PRODUCT LEAFLET AUGIER-BOX Remote Monitoring Unit for Street Lighting 1 60 11432-04/07/2011 Put a TECHNICIAN in each street lighting cabinet, and control them 24H per day! The Augier-Box Programmable Logic
More informationPressure Transmitter SIL
Pressure Transmitter SI Characteristics - TRANSDUCER - Pressure: Range: Output: Accuracy: Temperature of medium: Material enclosure: Pressure connection: Electrical connection: Protection: relative / absolute
More informationLVDT. Inductive Position Transducer - Hydraulic Series. SM-HYD Hydraulic Series. Key-Features:
LVDT Inductive Position Transducer - Hydraulic Series SM-HYD Hydraulic Series Key-Features: Content: - Screw flange M18x1,5 / M30x1,5 or plug-in flange Ø18 - Pressure up to 400 bar - Measurement range
More informationOperating Instruction
Level and Pressure Operating Instruction VEGASEL 643 6 5 + + 3 5 + + max. min. on VEGASEL 643 5 6 7 8 9 10 11 12 13 14 in out Contents Contents Safety information... 2 1 Product description 1.1 Function
More informationAR-DN-RS232. An-10 / Rapid RS232 Interface. Product Guide. Overview. Features
AR-DN-RS232 An-10 / Rapid RS232 Interface Product Guide Overview The AR-DN-RS232 is a device that is used as a 2 way gateway between third party systems and the CP An-10 or Rapid lighting control systems
More informationLED Driver Constant voltage
Driver LCU 100/96W 12/24V IP20 EXC EXCITE indoor IP20 series Product description LED Driver Universal input voltage range Constant output voltage Push terminals for simple wiring Nominal life-time up to
More informationDCPS Programmable DC Power Supply
_2015_v1 CINERGIA s Programmable Power Supplies are power electronics equipment designed to generate a constant voltage, current or power. Thanks to its bidirectional hardware the can source or sink the
More informationFL ballasts Electronic dimming. PCA T5 EXCITE lp Y, 3 and 4x14/24 W EXCITE T5
T PCA T EXCITE lp Y, and x1/ W EXCITE T Product description Processor-controlled ballast with y inside Highest possible energy class CEMA EEI = A1 BAT 1 oise-free precise control via DAI or DSI signal,
More informationLED PowerBlinder 4 ORDERCODE 41320
LED PowerBlinder 4 ORDERCODE 41320 Congratulations! You have bought a great, innovative product from Showtec. The Showtec LED PowerBlinder brings excitement to any venue. Whether you want simple plug-&-play
More informationLED Driver Linear / area fixed output
Driver LC 5W 5/3/35mA fixc lp SNC essence series Product description Fixed output built-in LED Driver Constant current LED Driver Output current 5, 3 and35 ma Max. output power 5 W Up to 91 % efficiency
More informationNSD Safety Mat Controller Modules Both Modules are compliant to OSHA & ANSI Standards - EN ISO EN EN 81-1 EN NSD VDC
Datasheet NSD Safety Mat Controller Modules Both Modules are compliant to OSHA & ANSI Standards - EN ISO 13849-1 EN 62061 EN 81-1 EN 50156-1 Approvals NSD-3580 24 VDC NSD-3590 115 TO 230 VAC Technical
More informationProduct and Applications Description
Product and pplications Description Diagram The transmitter 230V wave UP 110 (Diagram ) is a flushmounted device with radio communication for the wireless operation of room functions. It is possible to
More informationPHASED OUT. LED Driver Compact dimming. Driver LCAI 20W 350mA 900mA ECO SR ECO series
Product description Independent dimmable LED Driver Constant current LED Driver Output current adjustable between 350 900 ma Max. output power 20 W Nominal life-time up to 100,000 h 5-year guarantee Dimming
More informationINSTALLATION MANUAL. Model: Smart Analyzer Manufacturer: Smart Impulse. Power meter with consumption breakdown by use 03/12/13
INSTALLATION MANUAL Model: Smart Analyzer Manufacturer: Smart Impulse Power meter with consumption breakdown by use 03/12/13 Table of contents Table of contents... 2 1. Introduction... 3 2. Installation
More informationDigital Lighting Systems, Inc. PD804-DMX. Eight Channel DMX Pack. (includes information for PD804-DMX-S) USER'S MANUAL. PD804-DMX-UM Rev.
, Inc. Eight Channel DMX Pack (includes information for -S) S S S S 4 8 USER'S MANUAL -UM User's Manual - Page GENERAL DESCRIPTION The is an 8-channel DMX- compatible dimmer pack. It contains three printed
More informationLED Driver Linear / area dimming
Driver LCA 75W 900 1800mA one4all lp PRE PREMIUM series Product description Dimmable built-in constant current Adjustable output current between 900 and 1,800 ma via ready2mains Programmer, I-select 2
More informationUniversal Radio Cord Dimmer Order No.: Function
Order o.: 0335 0 a) b) Function The permits radio-operated control of lighting fixtures. The device permits switching (short actuation) or dimming (long actuation) of the lighting. The dimmer is operated
More informationPHASED OUT. LED Driver Linear / area dimming. Driver LCAI 100W 350mA 900mA ECO INDUSTRY sl ECO series
Product description Dimmable constant current built-in control gear for LED, particularly suitable for industrial applications in tough enviromments such as cold warehouses or factories with elevated ambient
More informationLED Driver Constant voltage
Driver LCA 100W 24V one4all lp PRE PREMIUM series Product description Dimmable 24 V constant voltage LED Driver for flexible constant voltage strips One4all interface and ready2mains enable different dimming
More informationSynchroniser Relay SYN-7
Synchroniser Relay SYN-7 1/19 Index 1 General Remarks...3 2 Operating Principle...3 2.1 Isolated Operation (Firmware Version V1.14 or higher)...4 2.2 Usage as a locking Relay...4 2.3 Switching onto Dead
More informationLED Driver Constant voltage
Driver LCA 1W 24V one4all lp PRE PREMIUM series Product description Dimmable 24 V constant voltage LED Driver for flexible constant voltage strips One4all interface and ready2mains enable different dimming
More informationTD - Power Supply LP DALI&Switch Dim Mono PRE (CV) MM-IP20 User Manual
TD - Power Supply LP DALI&Switch Dim Mono PRE (CV) MM-IP20 User Manual Item no.: NT-244-101 1. Product Description The TD-Power Supply SC DALI & Switch Dim Mono is a dimmable 24V constant voltage LED driver
More informationCONTROLLING LED LIGHTING WITH RAKO DIMMERS AND MODULES. 1. Constant current single channel. 2. Constant current three channel.
LED lighting is becoming more widely used and are set to become the dominant light source of the future. All LED lamps need an associated driver unit to limit the current driving the LED. Some newer lamps
More informationTIM-018 Mk2. London Electronics Limited. Triple output loop splitter. Connection details and general information
London Electronics Limited Thorncote Road, Near Sandy, Bedfordshire SG19 1PU Tel +44(0)1767 626444 Fax +44(0)1767 626446 www.london-electronics.com help@london-electronics.com Triple output loop splitter
More informationgesis EIB V Manual Installation system for European Installation Bus Products and Objects description
gesis EIB V Installation system for European Installation Bus Manual Products and Objects description Doc. No. BA000231 Revision D (10/2010) 2010 Wieland Electric GmbH Contents Contents 1 About This Manual...
More informationArtistic Licence. Candle-Power CP12. User Guide. Download this user guide by scanning the following QR code: Candle-Power CP12 User Guide Version 4-8
Artistic Licence Candle-Power CP12 User Guide Download this user guide by scanning the following QR code: Version 4-8 Connections 1 2 3 4 5 6 4 5 6 Term DAT+ DAT- COM DAT+ DAT- COM DMX512 In DMX512 Loop
More information