4Q POWER AMPLIFIERS AC AND DC 3000VA 3x3000VA
|
|
- Tiffany Quinn
- 5 years ago
- Views:
Transcription
1 PERFORMANCES High accuracy High stability Fast transients High inrush current facilities Wide bandwidth 25 khz at -3dB Internal waveform DC and up to 10 khz Very low distortion Quadrant change without transition Very low output impedance Low noise RS232 APPLICATIONS One or three insulated outputs AC, AC+DC, DC Avionic networks Hz Industrial networks Hz Tests in accordance with standards ABD / MIL-STD-704 Disturbed networks AC or DC motor simulation Non-linear loads Harmonics generation DESCRIPTION PUISSANCE+ amplifiers are real 4 quadrants power amplifiers, single-phase or three-phase, operating in voltage regulation: o For each phase, an analog input receives a pilot signal whose amplitude is 0~±10 V (7.07 VRMS) peak, coming from amplifier internal synthetizer or from an external synthetizer, o After insulation, the equipment amplifies this signal depending on the selected range, with a very short propagation delay. o Outputs analog isolated, two per phase, return images of voltage and current at the output of the equipment with amplitude 0~±10 V peak. The linear technology used for these amplifiers allows: o A high dynamic, a very low distortion on a wide frequency range and a large bandwidth o To provide power peaks up to 4 times its nominal power o An easy integration for Real-Time or Power Hardware In the Loop applications with simulators o A power factor between +1 (source mode) and -1 (sink mode). Entirely self-sufficient with its local control on touch screen, they can be controlled remotely from a supervisor system via an Ethernet or RS232 link for easy integration in a complex test system. Document ref. Amplifiers 4Q AC DC Single-Three phases 3000VA V4 - Page 1 / 11
2 Document ref. Amplifiers 4Q AC DC Single-Three phases 3000VA V4 - Page 2 / 11
3 PA-3x3000 PA Q POWER AMPLIFIERS AC AND DC SINGLE-PHASE AMPLIFIERS Rated power 3000 VA Model 260V-24A 360V-17A Ranges 130 V 260 V 180 V 360 V Voltage (VRMS) 0~130 0~260 0~180 0~360 Current (ARMS) 0~24 0~12 0~17 0~8.5 Peak current 69 A peak 34 A peak 51 A peak 26 A peak Voltage (VDC) 0~±130 0~±260 0~±240 0~±480 Current (ADC) 0~±23 0~±11,5 0~±12 0~±6 THREE-PHASE AMPLIFIERS Rated power 3x3000 VA Model 260V-24A 360V-17A Ranges 130 V 260 V 180 V 360 V Voltage Ph.-N (VRMS) 0~130 0~260 0~180 0~360 Current per phase (ARMS) 0~24 0~12 0~17 0~8.5 Peak current (ARMS) 69 A peak 34 A peak 51 A peak 26 A peak Voltage on one output (VDC) 0~±130 0~±260 0~±240 0~±480 Current per output (ADC) 0~±24 0~±12 0~±12 0~±6 Connection IN-SERIES of amplifiers outputs is allowed in DC only. Connection IN PARALLEL of amplifiers outputs is not allowed. Three-phase system: For size and weight reasons, a three-phase amplifier PA-3x3000 is made of three single-phase amplifiers PA-3000 connected in Y. These three amplifiers are associated: one of the three is master, the two others are "slaves". The master amplifier provides to the slaves amplifiers a timing signal in order to control the phase shift, editable, between them. The master amplifier receives measures and status of the slaves amplifiers and ensures the communication with an external supervisor (PC or PLC). Document ref. Amplifiers 4Q AC DC Single-Three phases 3000VA V4 - Page 3 / 11
4 PERMANENT OPERATING AREAS IN AC These diagrams express the relationship between the current and the voltage for different values of power factor. X-coordinates express the voltage as a percentage of the range. Y-coordinates express the current percentage of the rated current of the range. Continuous operation is allowed below curves. Limitations are due to the heating of the power transistors. Operation above diagrams will result in: An immediate switch-off by over-current protection if current is above the limits, A break after a delay by thermal protection in case of overheating of the power parts. These features are for each phase. Blue trace: dephasing between voltage and current is null. The power factor PF is equal to 1 (generation on resistive load). Green trace: dephasing between voltage and current is 90 (π / 2). The power factor PF is equal to 0 (generation on inductive load). Red trace: dephasing between voltage and current is 180 (π). The power factor PF is equal to -1 (full absorption). PROTECTIONS Against overload: current limitation Amplifiers in linear technology can generate up to four times their rated power during short time. They are using voltage regulation with current limitation: if current is higher than programmed value, a timer starts. At the end of a programmable time between 0.1 and 5 seconds, output voltage decreases to limit current to the programmed value. Against short-circuit on output: automatic output switch-off Output is switched off on all phases et must be reactivated using touchscreen or an external command. Against overtemperature: automatic output switch-off A temperature sensor is installed on each power part. It switches off outputs of the three phases in case of overheating. After cooling, output must be reactivated using touchscreen or an external command. Against overvoltage and undervoltage amplifier is protected against overvoltage or undervoltage. If this event is very short, hardware protection will limit effects. If this event is too long (> 100 ms), output is switched off to protect power parts. The time-stamping of the events starts as soon as the source is powered. Date and time can be modified locally or remote. Document ref. Amplifiers 4Q AC DC Single-Three phases 3000VA V4 - Page 4 / 11
5 AMPLIFIER VERSUS POWER SUPPLY? External AF or input output INSULATED IMAGES Phase Image I Internal AF Image U Neutral Mains input AC Mains power supply DC POWER AMPLIFIER (PA) Each amplifier includes its internal AF, its analog input, its mains power supply, its power output and its two images outputs. External AF External AF input L input L output output Internal AF (unused) POWER AMPLIFIER (PA) N Internal AF POWER SOURCE (PS) N When connecting an external AF, equipment is used as an amplifier. When connecting the internal AF, equipment is used as a power supply. 4 QUADRANTS OPERATION Current In "Q1" and "Q3" areas, the amplifier behaves in GENERATOR or SOURCE : the instantaneous power is positive. In "Q2" and "Q4" areas, the amplifier behaves in ABSORBER or SINK : the instantaneous power is negative. Q2 (U<0 and I>0) Q3 (U<0 and I<0) Q1 (U>0 and I>0) Q4 (U>0 and I<0) Voltage Document ref. Amplifiers 4Q AC DC Single-Three phases 3000VA V4 - Page 5 / 11
6 POWER OUTPUT 4Q POWER AMPLIFIERS AC AND DC COMMON FEATURES TO ALL AMPLIFIERS Power Rated power 3000 VA or 3x3000 VA Ranges, voltage, current See boards page 2 Voltage accuracy Typical 0,1% of range + 0,1% of programmed value Resolution 12 bits Current accuracy Typical 0,1% of range + 0,1% of programmed value Resolution 12 bits Voltage distortion at full output power Typical < 0,3% Max < 0,7% Voltage regulation for a mains variation of +6% / -10% Max < 0,1% of rated voltage Voltage regulation for a current variation from 0 to 100% Max < 0,1% of rated voltage Noise Max RMS 0,02% of rated voltage Max peak to peak 0,3% of rated voltage Bandwidth Full scale DC 5 khz / 10 khz (1) Small signals at -3 db 25 khz Variation with a square signal pilot Rise time 10% / 90% < 20 µs Fall time 10% / 90% < 20 µs Transfer time < 20 µs Transition from Q1 to Q4 < 10µs Variation according temperature Typical 50 ppm/ C Max 100 ppm/ C Stability after 15 minutes of operation Max < 0,05% of rated voltage Insulation of the outputs versus case ground Measurement at 500 VDC > 100 MΩ Images outputs (2) Voltage image Max 6,7 VRMS Current image Max 6,5 VRMS Accuracy of the measurements displayed on the touch screen Voltage measurement 0,3% of range + 0,3% of measure Current measurement 0,3% of range + 0,3% of measure Notes: (1) All amplifiers are able to generate 5 khz at full scale. At 10 khz, output amplitude is reduced: a. to 220 VRMS for amplifier 260V-24A b. to 310 V for amplifiers 360V-17A (2) The analog outputs are insulated from power outputs. Document ref. Amplifiers 4Q AC DC Single-Three phases 3000VA V4 - Page 6 / 11
7 ENVIRONMENTAL PILOT SIGNAL INPUT MAINS 4Q POWER AMPLIFIERS AC AND DC Mains network PA-3000 PA-3x3000 Number of phases Single-phase Three-phase Ph. + N + T 3 Ph. + T (3) Voltage 230 VRMS ±10% 400 VRMS ±10% Frequency Hz Mains current PA-3000 PA-3x3000 Max at full output power 18 ARMS 18 ARMS / Ph. Protection Magneto thermal breaker Inrush current Limited to 2 x Max current Dielectric strength of the mains input versus the output connected to the case ground Measurement at 2500VRMS / 50Hz Courant < 10 ma Notes: (3) To balance the supply network, the three amplifiers are powered each between one phase and neutral of a three-phase network. Input signal amplitude (external feature) Insulation > 10 MΩ (4) Voltage for full output scale 7,07 VRMS / ± 10V peak Max. voltage ± 15 V peak Input impedance 10 kω Input signal frequency Fundamental DC 10kHz Harmonics (small signals) Max 50 khz Notes: (4) The Pilot analog inputs are insulated from power outputs. Metallic parts treatment Front panel Rear panel Temperature and humidity Storage temperature Operating temperature Relative humidity Sound level (fans at full speed) Measured at 1 m of front panel Marking Marking Index of protection Aluminum painted RAL7021 Black anodized aluminum -10 C à +85 C +0 C à +40 C 10% - 90% non-condensing < 70 dba CE IP20 Document ref. Amplifiers 4Q AC DC Single-Three phases 3000VA V4 - Page 7 / 11
8 MECHANI -CAL 4Q POWER AMPLIFIERS AC AND DC MECHANICAL FEATURES PA-3000 Dimensions and weight Width Depth (connectors excluded) Height Weight 483 mm (19 inches) 600 mm 222 mm (5U) 59 kg Rear panel PA Photo non contractual 1 2 Mains socket (connector is provided) Earth pin 7 SUBD female 9 pins for synchronization (used only for threephase systems) 3 Output power Phase + Neutral + Earth and «sense» (connector is provided) 8 SUBD female 9 pins for serial communication RS232 4 Insulated BNC socket input of «Pilot» signal for amplifier 9 RJ45 socket for Ethernet communication 5 Insulated BNC sockets output of «Pilot» signal for amplifier 10 Fans with variable speed 6 SUBD female 25 pins output of images of voltage and current Document ref. Amplifiers 4Q AC DC Single-Three phases 3000VA V4 - Page 8 / 11
9 MECHANI -CAL 4Q POWER AMPLIFIERS AC AND DC MECHANICAL FEATURES PA-3x3000 The three-phase amplifier PA-3x3000 is composed of three single-phase amplifiers PA-3000 connected in Y. To integrate the necessary synchronization connections, this equipment is offered in the form of a small cabinet of height 25U. Dimensions and weight Width Depth (connectors excluded) Height Weight 603 mm (19 inches) 800 mm 1370 mm (25U) 270 kg Links between amplifiers are already wired: sense, power outputs, synchronization signal between amplifiers. The user merely has to connect the cabinet to mains using the cable length 5 m provided then outputs and "sense" to use. The 'Pilot' inputs are connected to the internal synthesizer. These links may be replaced by links from the customer device SUBD female 25 pins output of images of voltage and current Power output 3 Phases + Neutral + Earth (common Neutral) «Sense» Phase + Neutral inputs of each amplifier Document ref. Amplifiers 4Q AC DC Single-Three phases 3000VA V4 - Page 9 / 11
10 LOCAL OR REMOTE CONTROL Managed by a Control board, the amplifiers have two operating modes: Local control: The control device equipped with a graphical touch screen disposed in front panel gives access to all the control functions and the display of the measures. Remote control: The control device has one TCP/IP Ethernet link and two serial links, RS232 and RS485, for a control through a remote PC. Control can be done either using PUISSANCE+ OPS3 software (not supplied), either directly via instructions TCP/IP or RS232 / RS485 using customer software. EXAMPLES OF LOCAL CONTROL: SINGLE-PHASE AMPLIFIER The amplifier is configured in "standalone mode. On the main screen, graphical objects (boxes, input boxes and dropdowns) are to set it up. Fields return the instantaneous values of voltage and current. LEDs indicate status: thermal fault, overcurrent detected... Other screens are to set up communications links or for the management of variable speed fans. Document ref. Amplifiers 4Q AC DC Single-Three phases 3000VA V4 - Page 10 / 11
11 EXAMPLES OF LOCAL CONTROL: THREE-PHASE AMPLIFIER Amplifier located on the top is set to mode Master, the other two to mode Slave (Slave 1 and Slave2). Commands and the display of the measures and the status of the three amplifiers are grouped on the touch screen of the amplifier "Master. ORDER INFORMATION PA- Power -AC/DC-4Q- Voltage - Current -2G Power (W) Voltage (V) and Current (A) 3000 values depend from model 3x3000 (boards page 2) Example: PA-3x3000-AC/DC-4Q-260V-12A Amplifier 3x3000 VA, 3x260V, 3x12A AVAILABLE OPTIONS (to order separately) PA-RC-ISO OUTPUT: analog output read-backs 0~±10V of voltage and current PA-RC-SPECIAL RANGE: customized ranges Please consult us. PA-RC-MISE EN BAIE: provision of a small cabinet height 25U (1372 mm) to install one to three amplifiers (without any electrical connection) PA-RC-MISE EN BAIE ET ARRET D URGENCE: provision of a small cabinet height 25U (1372 mm) to install one to three amplifiers with START / stop buttons and emergency stop management. This option is integrated into the amplifier PA - 3 x PA-RC-WIDE BW: bandwidth small signals increased from 25 khz to 50 khz PA-RC-L100: resistive load for 100% absorption. This option includes installation in a small cabinet height 29U (1570 mm) with START / STOP buttons and emergency stop management. Specification may change without notice Document ref. Amplifiers 4Q AC DC Single-Three phases 3000VA V4 - Page 11 / 11
POWER AMPLIFIERS 4 QUADRANTS 3x500 VA to 3x1500 VA - THREE-PHASES
PERFORMANCES High accuracy High stability Fast transients High inrush current facilities Wide bandwidth Very low distortion Quadrant change without transition Very low output impedance Low noise RS232
More informationRS232 AC-DC VOLTAGE POWER AMPLIFIERS PCU-10K / 15K / 20K / 24K-AB/4G/HP PERFORMANCES APPLICATIONS DESCRIPTION COMMERCIAL REFERENCES
PERFORMANCES High accuracy High stability Fast transients High inrush current facilities Wide bandwidth Very low distortion Quadrant change without transition Very low output impedance RS232 APPLICATIONS
More informationPS-3000-AVAS PS-5000-AVAS DC SOURCE FOR AUTOMOTIVE TESTS
PERFORMANCES High accuracy High stability Fast times of transition High inrush current Wide bandwidth Switching from Q1 to Q4 without transition Very low output impedance Ripple & noise superposition Dips
More information3 x 30 kva AC POWER SOURCE PCU-3x30000-AC/DC-300V-100A-2G-HP RS232
3 x 30 kva AC POWER SOURCE PERFORMANCES High accuracy High stability Fast transients High inrush current Wide bandwidth Very low distortion Very low output impedance Power analyzer included RS232 APPLICATIONS
More informationDC 4Q POWER AMPLIFIER 200kW 2 RANGES HIGH POWER RS232
PERFORMANCES High accuracy High stability Fast transients High inrush current facilities Very low noise Very low output impedance Quadrant change without transition Power analyzer included Reverse polarity
More informationRS232. DC POWER SUPPLY 20kW 3 RANGES
PERFORMANCES High accuracy High stability Fast transients High inrush current facilities Very low noise Very low output impedance Switching from Q1 to Q4 without transition Ripple & noise superposition
More information22 kw 4Q POWER AMPLIFIER RS232
22 kw 4Q POWER AMPLIFIER PERFORMANCES High accuracy High stability Fast transients High inrush current facilities Very low noise Very low output impedance Quadrant change without transition Power analyzer
More informationAC CURRENT GENERATOR POC-6000 (current from 0 to 1000 ARMS)
AC CURRENT GENERATOR PERFORMANCES Wide range of current 50 db dynamic range Signal-to-noise ratio: 80 db open loop protection Stability < 0,1% Very low THD distortion < 0,3% External synchronization Build-up
More information200 kw 4Q POWER AMPLIFIER RS232
200 kw 4Q POWE AMPLIFIE PEFOMANCES High accuracy High stability Fast transients High inrush current facilities Very low noise Very low output impedance Quadrant change without transition Power analyzer
More informationDIFFERENTIAL CURRENT GENERATOR «POCDIF» (AC/DC - 32A - 50V - 12 ranges)
PERFORMANCES 12 ranges of AC current from 16 ma to 128 A peak AC permanent current up to 26 ARMS Nine ranges of DC permanent current from 16 ma to 12 A DC current ± 6mA or ± 10 ma stackable to AC current
More informationDIFFERENTIAL CURRENT GENERATOR «POCDIF» (AC/DC - 32A - 50V - 12 ranges)
PERFORMANCES 12 ranges of AC current from 16 ma to 128 A peak AC permanent current up to 26 ARMS Nine ranges of DC permanent current from 16 ma to 12 A DC current ± 6mA or ± 10 ma stackable to AC current
More informationPA-AB 4Q POWER AMPLIFIER VA Page 1/5
PA-AB 4Q POWER AMPLIFIER 600-1000-2000-3000-5000VA Page 1/5 PA series is a real 4 quadrants AC+DC amplifier to test or simulate all kind of loads or generators with power, high dymamic, a low distortion
More informationPA-AB 4Q POWER AMPLIFIER
PA series is a real 4 quadrants AC+DC amplifier to test or simulate all kind of loads or generators with power, high dymamic, a low distortion and a large bandwidth. Our own high performance linear technology
More informationMULTICHANNEL ACQUISITION SYSTEM
PERFORMANCES Simultaneous acquisitions of 2 to 20 analog channels and 32 digital channels 1.5 MEch/s and 16 bits per channel Memory 1 GEch / card Synchronous mode (1024 points per period) Transfer to PC
More informationLVA 4-Quadrant Amplifier 1000
LVA 4-Quadrant Amplifier 1 AUTOMOTIVE SUPPLY SIMULATION AT IT S BEST The relating standards: ISO 7637-2/-3 ISO 167-2 ISO 21848 LV 124 VDA 32 (LV 148) SAE J 1113-11 BMW GS 92 BMW GS 924-2-2 BMW GS 926 Ford
More informationElectronic AC Load ZSAC Series. 400 W up to 21,000 W 260 V up to 440 V 3 A up to 100 A. Rev. 3.03
Electronic AC Load Series 400 W up to 21,000 W 260 V up to 440 V 3 A up to 100 A Rev. 3.03 Electronic AC Loads, Series Interface overview RS-232 USB GPIB LAN System bus Analog / Analog isolated X X Standard
More informationApplications Avionics Testing Power Line Simulation Production Test - Power Supplies - UPS - Telecom. SMARTWAVE Programmable AC/DC Power Source
Applications Avionics Testing Power Line Simulation Production Test - Power Supplies - UPS - Telecom SMARTWAVE Programmable AC/DC Power Source PRODUCT OVERVIEW of cycles for each segment, the user can
More informationAPS series of 4-quadrant amplifiers
APS series of 4-quadrant amplifiers 4-QUADRANT VOLTAGE / CURRENT AMPLIFIER Fig. 1: 4-quadrant amplifier APS 1000 NEW: Constant current mode The adjustable and desired output current is automatically regulated
More informationLVA 4-Quadrant Amplifier 5000
LVA 4-Quadrant Amplifier 5 AUTOMOTIVE SUPPLY SIMULATION AT IT S BEST Example: LVA 1 Front panel Extremely low harmonic distortion - even under very non-linear load conditions Very fast slew rate > 2V/µs
More information400 W up to 21,000 W 260 V up to 440 V 3 A up to 100 A. Electronic Load ZSAC
400 W up to 21,000 W 260 V up to 440 V 3 A up to 100 A Electronic Load Electronic AC Loads, Interface overview RS-232 USB GPIB LAN System bus Analog X Analog isolated X Standard ption / not available 4226
More informationATV12H018F1 variable speed drive ATV kW hp V - 1ph
Characteristics variable speed drive ATV12-0.18kW - 0.25hp - 100..120V - 1ph Main Range of product Altivar 12 Product or component type Product destination Product specific application Assembly style Component
More informationATV12H037F1 variable speed drive ATV kW hp V - 1ph - with heat sink
Characteristics variable speed drive ATV12-0.37kW - 0.55hp - 100..120V - 1ph - with heat sink Main Range of product Altivar 12 Product or component type Product destination Product specific application
More informationDRTS 66 The new generation of advanced test equipments for Relays, Energy meters, Transducers and Power quality meters
The new generation of advanced test equipments for Relays, Energy meters, Transducers and Power quality meters Testing all relay technologies: electromechanical, solid state, numerical and IEC61850 Manual
More informationMultimeter 500CVD21 RTU500 series
Remote Terminal Units - Data sheet Multimeter 500CVD21 RTU500 series CT/VT interface with 4 voltage and 24 current inputs for direct monitoring of 3/4 wire 0 300 V AC (line to earth), 0...500 V AC (phase
More informationSide view View from below Rear view
Dimension diagrams All dimensions in mm Side view View from below Rear view Cut out: 138 +0,8 x 138 +0,8 mm Typical connection SPS SPS 11 12 13 14 15 16 1 2 3 4 5 6 7 8 9 10 DSUB-9 5 4 3 2 1 8 7 6 5 4
More informationLVA series of 4-Quadrant amplifiers
LVA series of 4-Quadrant amplifiers AUTOMOTIVE SUPPLY SIMULATION AT IT S BEST LVA 1 Front panel Extremely low harmonic distortion - even under very non-linear load conditions Very fast slew rate > 2V/µs
More informationPE Electrical Machine / Power Electronics. Power Electronics Training System. ufeatures. } List of Experiments
Electrical Machine / Power Electronics PE-5000 Power Electronics Training System The PE-5000 Power Electronics Training System consists of 28 experimental modules, a three-phase squirrel cage motor, load,
More informationGF 467F FUNCTION GENERATOR. PROTECTED RS232 + (USB OR LAN)* LabVIEW 0,01 Hz to 5 MHz CMos. Specifications. Other specifications
FUNCTION GENERATOR EAN CODE : 3760244880468 5 MHZ+RS232++(USB or LAN)* GF 467F COMPLETE : Reciprocal frequency counter 50 MHz. - Internal linear or logarithmic sweep, and external VCF or FM modulation.
More informationElgar SmartWave Series VA V A. High Performance AC/DC Power Source. and Boeing standards
Elgar SmartWave Series High Performance AC/DC Power Source and Boeing standards 1750 22200 VA 156 312 V 6.5 192 A 208 230 400 230 The Elgar SmartWave (SW) Series of AC power sources offers powerful waveform
More informationEV series of AC voltage amplifiers
EV series of AC voltage amplifiers Wide frequency range AC power amplifier system The applications: - Component testing - Measuring equipment testing - Ignition pulse testing (lighting equipment) High
More informationHV / MV / LV electrical network quality analyzers Class A. Communication port: local, modem, integrated Ethernet, multi-point
2010 MAP Range HV / MV / LV electrical network quality analyzers Class A > Network quality Analyzers PRODUCT ADVANTAGES COMPLIANT with the EN 61000-4-30 standard, Class A DETECTION of the fault LOCATION
More informationParallel AMX AC Power Systems
Parallel AMX AC Power Systems 8kVA to 30kVA 20-5,000 Hz 1Ø4 0-338VL-N 2Ø4 0-600V L-L 4 0-338V L-N /585V L-L Standard Features: Master/Slave Operation of 2 to 5 AMX AC s provides AC Power Levels to from
More informationEL-AC Electronic Load
s are power electronics devices that behave as an electrical load. While most electronic loads are dissipative, CINERGIA offers a comprehensive range of, and & full 4Q and full regenerative electronic
More informationVoltage Volts AC RMS , 1 Phase
The operational specifications of the Elgar EW 3001 are listed below. All specifications are tested according to the standard Elgar test procedures. All specifications are based on a full rated power resistive
More informationSolid State General Communication Power Amplifier
The GCS1D2GUT (SKU 4062) is suitable for broadband high power linear applications in the HF frequency range. This rack mount amplifier utilizes pushpull MOSFET power devices that provide high gain, wide
More informationGutor PxW AC UPS Designed for North American Market
Gutor PxW AC UPS Designed for North American Market PEW 5 200 kva single phase PDW 10 220 kva three phase Higher ratings upon request schneider-electric.com 2 schneider-electric.com schneider-electric.com
More informationATV12HU40M3 variable speed drive ATV12-4kW - 5hp V - 3ph - with heat sink
Characteristics variable speed drive ATV12-4kW - 5hp - 200..240V - 3ph - with heat sink Main Range of product Altivar 12 Product or component type Product destination Product specific application Assembly
More informationGE+ Grid Emulator. Key features. Highlights. High-Resolution and Dynamics. Efficiency and Flexibility. Smooth Integration. Harmonics Generation
GE+ Grid Emulator CINERGIA s Grid Emulators are programmable Voltage Sources designed to create stable AC grids as well as Disturbances. Based on a Regenerative and Bidirectional power hardware it is a
More informationArbitrary/Function Waveform Generators 4075B Series
Data Sheet Arbitrary/Function Waveform Generators Point-by-Point Signal Integrity The Arbitrary/Function Waveform Generators are versatile high-performance single- and dual-channel arbitrary waveform generators
More informationSPECIFICATION. Online UPS 3000VA
Page 1 / 7 DESCRIPTION Pure sine-wave output UPS on-line double conversion type. INPUT AC Mains voltage 230V ac 1 phase Mains voltage range 184...264V ac Mains frequency range 47...63Hz Power factor at
More informationLOW POWER PLA SERIES. PLA Series Brief Profile. Interfaces. Electronic DC Loads
Electronic DC Loads LOW POWER PLA SERIES PLA Series Brief Profile The electronic loads of PLA series combine the classic design of large, easy-to-read displays with modern interfaces and a wide range of
More informationApplications. Other applications include:
California Instruments CSW Series High Performance Programmable AC and DC Power Source Combination AC and DC Power Source 2Hz-7,990Hz Output Frequencies Arbitrary and Harmonic Waveform Generation Built-In
More informationATV12H037F1 variable speed drive ATV kW hp V - 1ph - with heat sink
Characteristics variable speed drive ATV12-0.37kW - 0.55hp - 100..120V - 1ph - with heat sink Product availability : Stock - Normally stocked in distribution facility Price* : 191.76 USD Main Range of
More informationPD300. Transformer, generator and motor protection Data sheet
PD300 Transformer, generator and motor protection Data sheet DSE_PD300_eng_AO No part of this publication may be reproduced by whatever means without the prior written permission of Ingeteam T&D. One of
More information250 / 500 Vdc. Advanced Features. Performance. Reliance. Brilliance.
California Instruments Asterion AC Series High Performance Programmable AC / DC Power Source 500 VA - 9000 VA 200 / 400 Vac 250 / 500 Vdc Advanced Features High power density in 1U chassis, up to 1.5kVA
More informationGE+ Grid Emulator Plus
GE+ Grid Emulator Plus CINERGIA s Grid Emulators are programmable Voltage Sources designed to create stable AC grids as well as electrical disturbances. Based on a Regenerative and Bidirectional power
More informationOUTPUT CHARACTERISTICS
ELECTRONIC PTE RANGE Protective relay test sets with direct on-board control and computer-based test automation THE ELECTRONIC PTE TEST EQUIPMENT RANGE The electronic PTE test equipment range has been
More informationDECLARATION OF CONFORMITY
DECLARATION OF CONFORMITY Manufacturer's Name: Transmille Ltd. Manufacturer's Address: Unit 4, Select Business Centre Lodge Road Staplehurst TN12 0QW. United Kingdom. Declares, that the product Product
More informationThe series allows users to compose. amplify the analog signal from arbitrary signal generator. Thus, it is capable of simulating the
Programmable AC Power Source MODEL 61500 SERIES Key Features: PROGRAMMABLE AC POWER SOURCE MODEL 61500 SERIES Chroma AC power source 61500 series sets waveform as well as measurements such as up the new
More informationEAC/AFV-P SERIES. High performance programmable AC power source 600 VA to 5 kva only in 2 U or 5 U
EAC/AFV-P SERIES High performance programmable AC power source 600 VA to 5 kva only in 2 U or 5 U N ONLY 5I U 2U/ EAC/AFV-P Series General Features Output frequency up to 15 1000 Hz AC source with DC output
More informationATV12HU22M2. Main. Range of product Altivar 12. Component name Quantity per set Set of 1. Built-in fan. Motor power hp Communication port protocol
Product datasheet Characteristics ATV12HU22M2 Complementary Main Range of product Altivar 12 Product or component type Product destination Product specific application Assembly style Component name Variable
More informationPower IT LV Active Filters PQFI PQFM PQFK. The ABB comprehensive solution for active filtering of harmonics
Power IT LV Active Filters PQFI PQFM PQFK The ABB comprehensive solution for active filtering of harmonics Harmonics and Power Quality Power Quality relates to the amplitude, frequency and distortion of
More informationFeatures 100A400AM20. 4kHz 400MHz Class A Portable Full VSWR tolerant CE & RoHS compliant High Efficiency
Specifications Class A Portable Full VSWR tolerant CE & RoHS compliant High Efficiency Features The Model is a solid-state, self -contained, air-cooled, broadband amplifier designed for applications requiring
More informationStabilized Differential Relay SPAD 346. Product Guide
Issued: July 1998 Status: Updated Version: D/21.03.2006 Data subject to change without notice Features Integrated three-phase differential relay, three-phase overcurrent relay and multiconfigurable earth-fault
More informationTechnical Data Sheet. Uninterruptible Power Supply On-line VH Series UPS. Critical Power UL / 208V
Technical Data Sheet Uninterruptible Power Supply On-line VH Series UPS 2000-3000 UL / 208V GE Consumer & Industrial SA General Electric Company CH 6595 Riazzino (Locarno) Switzerland T +41 (0)91 / 850
More informationProgrammable AC Power Source Model 9801
Data Sheet Programmable AC Power Source The 9801 is both a programmable AC power source and measurement tool in a compact benchtop package. This fully programmable linear AC source delivers up to 300 VA
More informationVoltage Transient Emission Test
Manual For Operation AN 200 Series Voltage Transient Emission Test AN 200 AN 200B The AN 200 is used to evaluate automotive electrical and electronic components for conducted emissions of transients along
More informationCMC 256plus - protection relay test set and universal calibrator
Technical Data - protection relay test set and universal calibrator The is the universal solution for testing old and new generation relays and calibrating all kinds of meters, PQ devices and transducers.
More informationEthernet-Based Temperature, Voltage and Strain Measurement Modules
Ethernet-Based Temperature, Voltage and Strain Measurement Modules OMB-NET6000 Series OMB-NET6220 shown smaller than actual size. U 12 Analog Inputs U 8 Digital I/O U Simultaneous Sampling U Multiple Trigger
More informationCalifornia Instruments BPS Series kva V A / Phase. Overview. High Power AC Source. Expandable Power Levels.
California Instruments Overview High AC Source Expandable Levels Remote Control 30 180 kva 150 400 V 0 400 A / Phase 208 230 400 480 Introduction The consists of multiple high power AC power systems that
More informationMaximum power. Nominal voltage. Operating temperature 0 to 50ºC. Humidity without condensation 5 95 % Contamination level 2 Current input features
s Features Portable power analyzer for three-phase and single-phase electrical networks with simultaneous measurement of leakage current, power quality and recording of transients. is the best tool for
More informationModel 2450 Interactive SourceMeter Instrument
Keithley Instruments, Inc. 28775 Aurora Road Cleveland, Ohio 44139 1-888-KEITHLEY http://www.keithley.com Model 2450 Interactive Meter Instrument Specifications SPECIFICATION CONDITIONS This document contains
More informationHigh Stability Voltage Source
Bilt System module - BE2100 High Stability Voltage Source Voltage to ±12V, current to ±200mA High Resolution: 21 bits, 6 ½ digits Ultra Low Noise: down to 6µVp-p Clean output noise spectrum with no spike
More informationUser-selectable output bus voltages for optimized voltage/current matching to load requirements.
Three Axis Gradient Amplifier 3-Axis 700A Precision Gradient Amplifier System 1500 VDC (OEM adjustable down to 800V) 100% Digital D-SERIES Technology Hi-Speed, Single Fiber-Optic Digital Command Universal
More informationMODEL 9050 EXTENDED SPECIFICATIONS. 50ppm TRANSPORTABLE CALIBRATOR
MODEL 9050 EXTENDED SPECIFICATIONS Ü 50ppm TRANSPORTABLE CALIBRATOR 9050A EXTENDED SPECIFICATIONS General Specifications TRANSMILLE LTD Warm Up Time Double the time since last used up to 20 minutes maximum
More informationAC/DC Power Sources ACS Series
AC/DC Power Sources ACS Series 1-phase systems 400 VA - 6000 VA 1 1-Phase AC/DC Power Sources ACS Series 400 VA - 6000 VA 1-phase AC/DC power source ACS 800-PS Special Features Overview AC and DC operation
More informationAF91 Adjustable Frequency Drives Series B
Effective: January, 00 Page New Information AF9 Adjustable Model AF9 Description Model AF9 Adjustable Frequency AC Drives are designed to provide adjustable speed control of -phase motors. These microprocessor-based
More informationLED Driver Compact dimming
Driver LCAI 35W 350mA 900mA ECO C ECO series Product description Dimmable built-in LED Driver for LED Constant current LED Driver Output current adjustable between 350 900 ma Max. output power 35 W Nominal
More informationLow Noise Variable Gain Low Frequency Voltage Amplifier
Measurement Features Variable Gain 40 to 100 db, Switchable in 20 db Steps Bipolar Input Stage, Recommended for Low Impedance Sources Smaller than 100 Ω Very Low Input Voltage Noise: 700 pv/ Hz DC-Coupled,
More informationUMG 509-PRO. Multifunction power analyser with RCM
UMG 509-PRO Multifunction power analyser with RCM Power quality RCM Residual current monitoring Ethernet connection Ethernet-Modbus gateway Graphic programming Alarm management Communication Profibus (DP/V0)
More informationDCPS Programmable DC Power Supply
_2015_v1 CINERGIA s Programmable Power Supplies are power electronics equipment designed to generate a constant voltage, current or power. Thanks to its bidirectional hardware the can source or sink the
More informationBecause you can t afford downtime
Agilent AC6800 Series Basic AC Power Sources Because you can t afford downtime Data Sheet Engineer reliability into your designs with a new basic AC source alternative from Agilent and test with conidence
More information200ADM-P. Current Injection System with Phase Shift A 3.000s 2.000A 50.00Hz 0.0. Features
CT ratio Power Harmonics ac+dc 200ADM-P Current Injection System with Phase Shift Features 0-200A output current True RMS metering with 1 cycle capture Variable auxiliary AC voltage/current output with
More informationPower Quality Solutions PQSine P-Series of Active Harmonic Filters and Power Optimizers
EPCOS Product Brief 2017 Power Quality Solutions of Active Harmonic Filters and Power Optimizers EPCOS has been offering a comprehensive range of key components for power factor correction (PFC) and power
More informationLow Noise Variable Gain Low Frequency Voltage Amplifier
Features Variable Gain 40 to 100 db, Switchable in 20 db Steps Bipolar Input Stage, Recommended for Low Impedance Sources Smaller than 100 Ω Very Low Input Voltage Noise: 700 pv/ Hz DC-Coupled, Single
More informationChapter 6 Specifications
Chapter 6 Specifications DC Characteristics Function Range [2] Test Current or Burden Voltage DC Voltage DC Current Resistance [6] 24 Hour [3] T CAL ±1 Accuracy Specifications: ± (% of reading + % of range)
More information8101 SPECIFICATION SHEET
2 5 0 7 W a r r e n S t r e e t, E l k h a r t, I N 4 6 5 1 6 U S A 5 7 4. 2 9 5. 9 4 9 5 w w w. A E T e c h r o n. c o m The AE Techron 8101 power supply amplifier features an advanced switchmode design
More informationThis convection-cooled series is designed for use in commercial and industrial environments in temperatures up to 50 C.
RoHS Lead-Solder-Exemption Compliant Automatic 115/230 Input Voltage Selection All Outputs Fully Regulated Remote Sense, Overvoltage Protection and Overtemperature Protection Power Fail Signal Included
More informationPHASED OUT. LED Driver Compact dimming. Driver LCAI 55W 900mA 1750mA ECO C ECO series
Product description Dimmable built-in LED Driver for LED Constant current LED Driver Output current adjustable between 900 1,750 ma Max. output power 55 W Nominal life-time up to 100,000 h 5-year guarantee
More informationSolid State Broadband High Power Amplifier
The BBS4A5AVT (2157) is suitable L & S Bands broadband or band specific high power applications. This amplifier utilizes high power GaN devices that provide wide frequency response, high gain, high peak
More informationDodecahedron Speaker Set
Dodecahedron Speaker Set Omnidirectional Sound Source Comprised of the DS3 Dodecahedron Loudspeaker and the PA3 Power Amplifier, the set generates a Pink noise signal with an acoustically-flat frequency
More informationPEAK OUTPUT CURRENT 1. MAP V 4.7V to 5.8V 8A 11A 0.2% ±1% 1% 4.9V to 5.1V PEAK OUTPUT CURRENT 4 LINE REGULATION
The Bel Power Solutions MAP30/40/42 Series of power supplies combines low cost and universal input in a board-only power solution to meet commercial and industrial requirements. Full international safety,
More information2.1 Performance Standards The UPS is designed with the applicable sections of UL, CUL, and ISO The UPS has UL and CUL listing.
1.0 Scope This document describes the specification for Toshiba 1000 Series On-Line Uninterruptible Power System (UPS). The UPS will supply a computer grade AC output sine wave which is unaffected by the
More informationGrid Measurement Modules
Grid Measurement and Protection Module GMP232 The GMP232 module enables the safe, reliable and fast measuring of all relevant values for threephase electrical networks. It also provides a number of monitoring
More informationMODEL 9041 EXTENDED SPECIFICATIONS. 25ppm TRANSPORTABLE CALIBRATOR
MODEL 9041 EXTENDED SPECIFICATIONS 25ppm TRANSPORTABLE CALIBRATOR 9041 EXTENDED SPECIFICATIONS General Specifications TRANSMILLE LTD Warm Up Time Double the time since last used up to 20 minutes maximum
More informationDRTS-6. DRTS-6 has been designed to test: DRTS-6. Advanced Protection Relay Test Set and Measurement System
DRTS-6 Advanced Protection Relay Test Set and Measurement System MULTI-TASKING EQUIPMENT DESIGNED FOR TESTING PROTECTION RELAYS, ENERGY METERS, TRANSDUCERS POWERFUL AND LIGHTWEIGHT HIGH ACCURACY: BETTER
More informationSPAD 346 C Stabilized differential relay
SPAD 346 C Stabilized differential relay Stabilized Differential Relay Type SPAD 346 C Features Integrated three-phase differential relay, three-phase overcurrent relay and multiconfigurable earth-fault
More information120W UHF Transmitter/Repeater
Product Features 470 MHz - 860 MHz Broadband Transmitter/Repeater LDMOS Power Amplifier provides 120 Watt output for ATSC, ATSC-M/H, CMMB, DTMB, DVB-T/H, DVB-T2, DVB-SH, ISDB-T/TB,, DAB, DAB+ and T-DMB
More informationLow Noise Variable Gain Low Frequency Voltage Amplifier
Features Variable Gain 40 to 100 db, Switchable in 20 db Steps Bipolar Input Stage, Recommended for Low Impedance Sources Smaller than 100 Ω Very Low Input Voltage Noise: 700 pv/ Hz DC-Coupled, Single
More informationNetworks IT, TN, TT networks 3 and 4-phase networks Up to 4 single-phase networks. Measured data memory 256 MByte Flash 32 MB SDRAM
Power quality Colour graphical display Ethernet connection Ethernet-Modbus gateway Graphic programming Alarm management UMG 508 Multifunction power analyser Communication Profibus (DP/V0) Modbus (RTU,
More informationPROGRAMMABLE AC POWER SOURCE MODEL 6500 SERIES MODEL 6500 SERIES. Programmable AC Power Source. Key Features:
Programmable AC Power Source MODEL 6500 SERIES Key Features: PROGRAMMABLE AC POWER SOURCE MODEL 6500 SERIES The global AC power testing requirements demand more sophisticated AC Power Source that is capable
More informationLED Driver Compact fixed output 4,5 83,5 93. Ordering data. Type
Product description Fixed output built-in LED Driver Constant current LED Driver Output current 30, 00 or 700 ma Max. output power 20 W Nominal life-time up to 0,000 h For luminaires of protection class
More informationCalifornia Instruments MX Series II kva V A / Phase. Overview
California Instruments M Series II Overview 15 135 kva 150 400 V High AC and DC Source Programmable AC and DC power for frequency conversion and product test applications Expandable Levels Available output
More informationS11 Adjustable Speed Drive Engineering Specification
PART 1 - GENERAL 1.0 Scope This specification shall cover Toshiba S11 AC Variable Frequency Drives, 6 pulse for 3- phase 200-240VAC, 380-500VAC and single phase 200V to 240VAC. 1.1 References A. National
More informationPower quality Harmonics up to 40th harmonic Rotary field components Distortion factor THD-U / THD-I
Memory 256 MB Alarm management Residual current measurement Homepage Ethernet-Modbus gateway BACnet (optional) UMG 96 RM-E Power analyser with Ethernet and RCM Communication Modbus (RTU, TCP, Gateway)
More informationGreen LED (right of 'D' type connector)
3050A EXTENDED SPECIFICATIONS General Specifications TRANSMILLE LTD Warm Up Time Double the time since last used up to 20 minutes maximum Standard Interfaces USB Optional Interfaces GPIB (IEEE-488) : RS232
More informationLED Driver Compact dimming
Driver LCAI 35W 3mA 900mA ECO C flat ECO series Product description Dimmable built-in LED Driver for LED Constant current LED Driver Output current adjustable between 3 900 ma Max. output power 35 W Nominal
More informationMARINE POWER CONVERSION & CONSULTING
MARINE POWER CONVERSION & CONSULTING SINGLE CABINET VERSION SHORE POWER CONVERTERS ZC SERIES 8-15 KVA (2X) 16-30 KVA Single phase DUAL CABINET VERSION STANDARD FEATURES : Wide input voltage range 85-265
More informationPP400B060-ND. H-Bridge POW-R-PAK IGBT Assembly 400 Amperes/600 Volts
Powerex, Inc., 173 Pavilion Lane, Youngwood, Pennsylvania 15697 (724) 925-7272 www.pwrx.com H-Bridge POW-R-PAK IGBT Assembly Q Q J P (8 PLACES) +DC C2E1 R (2 PLACES) PIN 1 N U B M N F DC L (6 PLACES) G
More informationSERIE E N. The E N series clamps use Hall-effect technology for the measurement of AC and DC currents from several milliamps to over 100 A.
Pinces Current ampèremetriques clamps for AC/DC pour current courant AC SERIE E N The E N series clamps use Hall-effect technology for the measurement of AC and DC currents from several milliamps to over
More information