A.LEDA WASH K5 A.LEDA WASH K10 A.LEDA WASH K20

Transcription

1 ENGLISH K5 K K C6 C65 C6 INSTRUCTION MANUAL Page 5 7 INDEX Contents Safety information Unpacking and preparation Installation and start-up Control panel Menu setting Maintenance Optional accessories Technical information Cause and solution of problems Channel functions Congratulations on choosing a Clay Paky product! We thank you for your custom. Please note that this product, as all the others in the rich Clay Paky range, has been designed and made with total quality to ensure excellent performance and best meet your expectations and requirements. Carefully read this instruction manual in its entirety and keep it safe for future reference. It is essential to know the information and comply with the instructions given in this manual to ensure the fitting is installed, used and serviced correctly and safely. CLAY PAKY S.p.A. disclaims all liability for damage to the fitting or to other property or persons deriving from installation, use and maintenance that have not been carried out in conformity with this instruction manual, which must always accompany the fitting. CLAY PAKY S.p.A. reserves the right to modify the characteristics stated in this instruction manual at any time and without prior notice.

2 SAFETY INFORMATION LED. Installation Make sure all parts for fixing the projector are in a good state of repair. Make sure the point of anchorage is stable before positioning the projector. The safety chain must be properly hooked onto the fitting and secured to the framework, so that, if the primary support system fails, the fitting falls as little as possible. If the safety chain gets used, it needs to be replaced with a genuine spare. Minimum distance of illuminated objects The projector needs to be positioned so that the objects hit by the beam of light are at least. metres (8 ) from the lens of the projector. Minimum distance from flammable materials The projector must be positioned so that any flammable materials are at least. metres (8 ) from every point on the surface of the fitting. Mounting surfaces It is permissible to mount the fitting on normally flammable surfaces. Maximum ambient temperature Do not operate the fixture if the ambient temperature (Ta) exceeds C ( F). IP IP protection rating The fitting is protected against penetration by solid bodies of over mm (.7 ) in diameter (first digit ), but not against dripping water, rain, splashes or jets of water (second digit ). Protection against electrical shock Connection must be made to a power supply system fitted with efficient earthing (Class I appliance according to standard EN 658-). It is, moreover, recommended to protect the supply lines of the projectors from indirect contact and/or shorting to earth by using appropriately sized residual current devices. Connection to mains supply Connection to the electricity mains must be carried out by a qualified electrical installer. Check that the mains frequency and voltage correspond to those for which the projector is designed as given on the electrical data label. This label also gives the input power to which you need to refer to evaluate the maximum number of fittings to connect to the electricity line, in order to avoid overloading. t c C Temperature of the external surface The maximum temperature that can be reached on the external surface of the fitting, in a thermally steady state, is C ( F). Maintenance Before starting any maintenance work or cleaning the projector, cut off power from the mains supply. LiFePO Battery This product contains a rechargeable lead-acid battery. To preserve the environment, please dispose the battery at the end of its life according to the regulation in force. Instructions on how to remove the battery from the product are available on The products to which this manual refers comply with the European Directives pursuant to: 6/5/EC - Safety of electrical equipment supplied at low voltage (LVD) /8/EC - Electromagnetic Compatibility (EMC) /65/EU - Restriction of the use of certain hazardous substances (RoHS)

3 UNPACKING AND PREPARATION IST/ x 8/85 Packing contents - Fig. UNLOCKED LOCKED PAN Mechanism Lock and Release (every ) - Fig.

4 INSTALLATION AND START-UP Installing the projector - Fig. The projector can be installed on the floor resting on special rubber feet, on a truss or on the ceiling or wall. WARNING: with the exception of when the projector is positioned on the floor, the safety cable must be fitted. (Cod. 5/ available on request). This must be securely fixed to the support structure of the projector and then connected to the fixing point at the centre of the base. Connecting and disconnecting power cable - Fig.

5 CONTROL PANEL 5 Mains NB: connecting one A.leda Wash K5 to the mains, it is possible to connect up to a maximum of A.leda Wash K5 in parallel at the same time. Connecting to the mains supply - Fig. 5 6 DMX 5 5 PIN DMX 5 5 DMX 5 PIN SCREEN SIGNAL SIGNAL SIGNAL SIGNAL SCREEN Connecting to the control signal line (DMX) - Fig. 6 Use a cable conforming to specifications EIA RS-85: -pole twisted, shielded, Ohm characteristic impedance, - AWG, low capacity. Do not use microphone cable or other cable with characteristics differing from those specified. The end connections must be made using XLR type or 5-pin male/female connectors. A terminating plug must be inserted into the last projector with a resistance of Ohm (minimum / W) between terminals and. IMPORTANT: The wires must not make contact with each other or with the metal casing of the connectors. The casing itself must be connected to the shield braid and to pin of the connectors. 7 Switching on the projector - Fig. 7 Press the switch. The projector starts resetting the effects. At the same time, the following information scrolls on the display: Model Firmware xxx (Fixture ID) System errors A.leda Wash Version X.X.X Dmx Address xxx E:... Date - Hour W:... On conclusion of resetting in case of absence of the dmx signal, Pan and Tilt move to the Home position (Pan 5% - Tilt 5%). The control panel (Fig. 7) has a display and buttons for the complete programming and management of the projector menu. The display can be in one of two conditions: rest status and setting status. When it is in the rest status, the display shows the projector s DMX address and the Fixture ID address (if set). During menu setting status, after a wait time (about seconds) without any key having been pressed, the display automatically returns to rest status. It should be noted than when this condition occurs, any possible value that has been modified but not yet confirmed with the F key will be cancelled. 5 Continue

6 8 Reversal of the display - Fig. 8 To activate this function, press UP B and DOWNCkeys simultaneously while the display is in the rest mode. This status will be memorised and maintained even for the next time it will be switched on. To return to the initial state, repeat the operation all over again. Setting the projector starting address On each projector, the starting address must be set for the control signal (addresses from to 5). The address can also be set with the projector switched off. Setting the address: see pag. 8. Setting the projector Fixture ID On each projector, the Fixture ID address must be set for an easy identification of the fixtures in an installation (ID from to 55). The Fixture ID address can be set with the projector switched off. Setting the Fixture ID: see pag. 8. Functions of the buttons - Using the menu F Confirms the displayed value, or activates the displayed function, or enters the successive menu. CDOWN Decreases the value displayed (with auto-repetitions) or passes to the next item in the menu. BUP Increases the value displayed (with auto-repetitions) or passes to the previous item in a menu. DLEFT Return to the top level. Commute from units, tens, hundreds, in the "Address", "Fixture ID" and "Calibration" menù. ERIGHT USING THE MENU: ) Press F once Main Menu appears on the display. ) Use the UP B and DOWN C keys to select the menu to be used: Setup (Setup Menu): To set the setting options. Option (Option Menu): To set the operating options Informations (Informations Menu): To read the counters, software version and other information. Manual Control (Manual control Menu): To trigger the test and manual control functions. Test (Test Menu): To check the proper functionning of effects Advanced (Advanced Menu): Access to the "Advanced menu" is recommended for a trained technical personnel. To enable the "Advanced" see pag. ) Press F to display the first item in the selected menu. ) Use the UP B and DOWN C keys to select the MENU items. Setting addresses and options with the projector disconnected The projector s DMX address, as well as other possible operating options, can also be set when the appliance is disconnected from the electricity supply. All that is needed is to press F to momentarily activate the display and thus access the settings. Once the required operations have been carried out, the display will switch off again after a wait time of seconds. 6

7 MENU SETTING Set Up Dmx Address Option Pan / Tilt Invert Pan Information System Errors Channel Mode Invert Tilt Fixture Hours Fixture ID Ethernet Interface Silent Mode Swap Pan-Tilt Encoder Pan-Tilt Standard LED Energy Tot System Version Option Quiet Board Diagnost. Information Manual Control Test Display Special Functions Pan/Tilt speed Dimmer curve RGB Gamma Dmx Monitor Fans Monitor Network params Advanced Halogen Mode Setting Default Preset User Preset User Preset User Preset 5 6 Manual Control Reset Test Pan / Tilt Advanced Access code Channel Colour All Upload Aleda fw Setup Model Calibration 7 Continue

8 NOTE: On grey the default options Set Up Dmx Address Address xxx SET UP MENU DMX ADDRESS NOTE: without the DMX signal the Address (XXX) flashing Allows you to select the DMX ADDRESS. ) Press F - the current DMX Adress appear on the display. ) Use the UP B and DOWN C, RIGHT E keys to plan the DMX Address. ) Press F to confirm the selection or LEFT D to keep current settings. Channel Mode Standard Shape Extended Extended RGBW CHANNEL MODE Allows you to select a channel arrangement from the two available. ) Press F - the current settings appear on the display (Standard or Vector). ) Use the UP B and DOWN C keys to select one of the following settings: - Standard - Shape - Extended - Extended RGBW ) Press F to confirm the selection or LEFT D to keep current settings. Fixture ID Value xxx FIXTURE ID Allows you to select the FIXTURE ID. ) Press F - the current Fixture ID appear on the display. ) Use the UP B, DOWN C, RIGHT E keys to plan the Fixture ID. ) Press F to confirm the selection or LEFT D to keep current settings. Ethernet Interface Control Protocol Repeat on DMX Universe ETHERNET INTERFACE It lets you set the Ethernet settings to be attributed to the projector. ) Premere F. ) Use the UP B and DOWN C keys to select the Ethernet Interface options to set: Control Protocol It lets you select the Control Protocol Art-net to assign according to the control unit used: ) Press F the current setting appears on the display. ) Use the UP B and DOWN C keys to select one of the following settings: - Disabled - Art-net on IP - Art-net on IP ) Press F to confirm the selection or LEFT D to keep the current setting. Repeat on DMX It lets you enable the transmission of the Ethernet protocol by DMX signal to all the connected projectors. ) Press F the current setting appears on the display. ) Use the UP B and DOWN C keys to select one of the following settings: - Disabled: DMX transmission disabled. - Enabled on primary: DMX transmission enabled. ) Press F to confirm the selection or LEFT D to keep the current setting. Universe It lets you assign the Universe number to be assigned to a series of projectors. ) Press F the current Universe address appears on the display. ) Use the UP B, DOWN C, RIGHT E keys to set the Universe address. ) Press F to confirm the selection or LEFT D to keep the current setting. 8

9 OPTIONS MENU Option Pan / Tilt Invert Pan On Off PAN / TILT Invert pan Used for reversing Pan movement. ) Press F - the current settings appear on the display (On or Off). ) Use the UP B and DOWN C keys to enable (On) or disable (Off) PAN inversion. ) Press F to confirm the selection or LEFT D to keep current settings. Invert Tilt On Off Invert tilt Used for reversing tilt movement. ) Press F - the current settings appear on the display (On or Off). ) Use the UP B and DOWN C keys to enable (On) or disable (Off) Tilt inversion. ) Press F to confirm the selection or LEFT D to keep current settings. Swap Pan-Tilt On Off Swap Pan-Tilt Used for swapping Pan and Tilt channels (as well as Pan fine and Tilt fine). ) Press F - the current settings appear on the display (On or Off). ) Use the UP B and DOWN C keys to enable (On) or disable (Off) Pan and Tilt channel swap. ) Press F to confirm the selection or LEFT D to keep current settings. Encoder Pan-Tilt On Off Encoder Pan-Tilt Used for enabling the Pan / Tilt encoders. ) Press F - the current settings appear on the display (On or Off). ) Use the UP B and DOWN C keys to enable (On) or disable (Off) Pan / Tilt encoders. ) Press F to confirm the selection or LEFT D to keep current settings. Silent mode Standard Quiet SILENT MODE It lets you select the Silent Mode from the two available. ) Press F the current setting appears on the display. ) Use the UP B and DOWN C keys to select one of the following settings: Standard: Maximum speed and consequently maximum effects noise level. Quiet: reduces the speed of some effects, thereby reducing their noise level. ) Press F to confirm the selection or LEFT D to keep the current setting. Display On Off DISPLAY Used for automatically reduce brightness on the display after about seconds in idle. ) Press F - the current settings appear on the display (On or Off). ) Use the UP B and DOWN C keys to enable (On) or disable (Off) the decreasing of display brightness. ) Press F to confirm the selection or LEFT D to keep current settings. Special Functions Pan / Tilt speed SPECIAL FUNCTIONS Pan / Tilt speed Lets you select two different Pan and Tilt speeds. ) Press F - the current setting appears on the display. ) Use the UP B and DOWN C keys to select one of the following settings: - Normal - Fast ) Press F to confirm the selection or LEFT D to keep current settings. Continue

10 Option Special Functions Dimmer Curve Dimmer Curve Lets you select four different Dimmer channel curves. ) Press F - the current setting appears on the display. ) Use the UP B and DOWN C keys to select one of the following settings: - Curve - Curve - Curve - Curve ) Press F to confirm the selection or LEFT D to keep current settings. RGB Gamma RGB Gamma Lets you select three different RGBW gamma curves. ) Press F - the current setting appears on the display. ) Use the UP B and DOWN C keys to select one of the following settings: - Gamma. - Gamma.5 - Gamma. ) Press F to confirm the selection or LEFT D to keep current settings. Halogen Mode Halogen Mode Lets you select five different halogen lamp simulations. ) Press F- the current setting appears on the display. ) Use the UP B and DOWN C keys to select one of the following settings: - Halogen OFF - Halogen Lamp - Halogen Lamp - Halogen Lamp - Halogen Lamp - Halogen Lamp 5 ) Press F to confirm the selection or LEFT D to keep current settings. Setting Default Preset User Preset User Preset User Preset Reset To Dafault Go Back Load Preset Save To Preset Load Preset Save To Preset Load Preset Save To Preset SETTING Used to save different settings of the items in the options menu and relative submenus. ) Press F - Default preset appears on the display. ) Use the UP B and DOWN C keys to select one of the following configurations: - Default preset (*) - User preset - User preset - User Preset ) Press F - Load preset X appears on the display. ) Use the UP B and DOWN C keys to select: - Load preset X to recall a previously stored configuration. - Save to preset X to store the current configuration. a confirmation message (Are you sure?) appears on the display. 5) Select YES to confirm the selection or NO to keep the current setting and return to the next higher level. (*) DEFAULT PRESET Used for restoring default values on all options menu items and relevant submenus. ) Press F, a confirmation message (Are you sure?) appears on the display. ) Select YES to confirm the selction or NO to keep current setting. OPTION DEFAULT Invert Pan Off Invert Tilt Off Swap Pan-Tilt Off Encoder Pan-Tilt On Display On Silent Mode Standard P/T Speed Fast Dimmer Curve Curve RGB Gamma Gamma.5 Halogen Mode Halogen Off

11 Information System Errors INFORMATION MENU SYSTEM ERRORS Shows a list of warnings and messages relevant to errors occurred since the fixtures switching-on. ) Pressing F you are allowed to reset the SYSTEM ERRORS list. A confirmation message (Are you sure you want to clear error list?) appears on the display. ) Select YES to reset the list or NO to go back. Fixture Hours Total Partial XXX XXX Reset... FIXTURE HOURS Used for displaying projector operating hours (total and partial). ) Press F - Hours total and partial appears on the display. Total counter Counts the number of projector working life hours (from manufacture to date). Partial counter Counts the number of partial projector working life hours since the last reset to date. ) Press F to reset partial projector working hours a confirmation message (Are you sure?) appears on the display. ) Select YES to reset partial projectors counter or NO to keep the current setting and return to the top menu level. LED Energy Tot LED ENERGY TOT Lets you view total LED working hours. ) Press F - to display total and partial Watts/hour: Total Total LED working hours from construction to date. Partial LED working hours from last reset to date. ) Press F to reset the partial counter. A confirmation appears on the screen (Are you sure?) ) Select YES to reset the partial counter or NO to keep the current setting and open the next menu level. System Version Board Diagnost. Dmx Monitor Board Revis. Hw.rv. CPU brd x.x.x x.x com.dev x.x : PT-f x.x x.x : Ld - Kxx x.x x.x Board Status Err% :PT-f Good. : Ld - Kxx Good. SYSTEM VERSION Used for displaying the software and hardware version of each board installed in the projector. CPU brd (CPU board) : PT-f (Scheda Pan / Tilt) : Ld - Kxx (Scheda LED) BOARD DIAGNOSTIC Used for displaying the status error of each board installed in the projector: : PT-f (Scheda Pan / Tilt) : Ld - Kxx (Scheda LED) DMX MONITOR Used for displaying the projector DMX channel level in bit (Val) and in percentage (Perc). Fans Monitor Fan PwrSp Head Speed (RPM) XXXX XXXX FANS MONITOR Used for displaying the speed of each fan installed in the projector: PwrSp (fan PSU) Head (fan head) Network params NETWORK PARAMS Allows the "Network" parameters of the projector to be displayed or: IP address: Internet Protocol address (two projectors must not have the same IP address) IP mask: Mac address: Media Access Control: the projector s Ethernet Address. Continue

12 MANUAL CONTROL Manual Control Reset No RESET Used for resetting the projector. ) Press F to reset the projectors, a confirmation message (Are you sure?) appears on the display. ) Select YES to starting reset the fixture or NO to keep the current setting and return to the top menu level. Channel CHANNEL Used for setting channel levels from the projector control panel. ) Press F - the first channel appears on the display. ) Use the UP B and DOWN C keys to select the required channel: ) Press F and use the UP B and DOWN C keys to select the required DMX level (value between and 55). ) Press LEFT D to return to the top menu level. TEST MENU Test Pan-Tilt Colour All TEST Allows you to check the proper functioning of effects. ) Press F to return to the top menu level. ) Use the UP B and DOWN C keys to select the required test. ) Press F to confirm the selection or LEFT D to keep current settings. Test sequence: Pan - Tilt effects (Pan & Tilt) Colour effects (CMY / CTO / Colour wheel) All effects ADVANCED MENU Advanced Code To enable the "Advanced Menu" set up the "Access code" () using the UP B, DOWN C, RIGHT E keys. Press F - "Menu advanced" appears on the display Upload Aleda fw Transfer the firmware on all the connected fixtures? Are you sure? /No UP LOAD FIRMWARE Allows you to transfer the firmware from fixture to all the connected fixtures. ) Press F, a confirmation message appears on the display. ) Select YES to start the firmware loading or NO to keep the current setting and return to the top menu level Setup Model Changing to a wrong model may damage the fixture. Are you sure? /No SETUP MODEL Allows you to change the default model of projector. ) Press F a confirmation message appears on the display. ) Select YES to define the model of projector or NO to keep the current setting and return to the top menu level. Calibration CALIBRATION Allows you to adjust effects from the control panel to obtain perfect uniformity between the projectors. ) Press F - channels appears on the display. ) Using the UP B and DOWN C keys, select the effect you wish to regulate. ) Press F and use the RIGHT E, UP B and DOWN C buttons to make the adjustment by setting a value between and 55. ) Press F to confirm the selection or LEFT D to keep current settings and return to the top level. FACTORY DEFAULT Allows you to restore default values of all channels (8). ) Press F a confirmation message appears on the display (Reset calibration to factory default?). ) Select YES to reset calibration to factory default or NO to keep the current setting and return to the top menu level.

13 6 5 Battery removal - Fig. This product contains a rechargeable lead-acid battery. To preserve the environment, please dispose the battery at the end of its life according to the regulation in force. LiFePO

14 MAINTENANCE Opening the covers - Fig. Removing/Assembling the lens unit - Fig. NB: Apply Loctite (p/n COL) to the threads of the screws () before tightening them. A torque of.n is recommended in order to avoid damaging the zoom movement actuators.

15 Replacing the line actuator - Fig. NB: It is highly recommended to use the DIM/ () template whenever it is necessary to replace one of the three Zoom movement line actuators. DIM/ ensures the actuator group is centred correctly on the lens plate before tightening the screws () that fasten the actuator in place. 5

16 OPTIONAL ACCESSORIES K5 C65 C65 Cover - Fig. C65 - Transparent cover C65 - Frosted cover C65 Transparent mask - Fig.

17 K 5 C655 C656 Cover - Fig. 5 C655 - Transparent cover C656 - Frosted cover C65 Transparent mask - Fig. 7 Continue

18 K 7 C658 C65 Cover - Fig. 7 C658 - Transparent cove C65 - Frosted cover 8 C657 Transparent mask - Fig. 8 8

19 TECHNICAL INFORMATION (8.66") 55 (6.") 7 (.7") 55 (6.") 5 (.65") Power supplies available -V 5/6Hz Input power K - 75VA K - 5VA K5-7VA Max 8VA (with A.leda Wash K5 connected in parallel) (.") (6.") 8 (5.") 5 (.6") (.65") 5 (.8") (.6") 6 (.7") Total output K5 - Max lumens K - Max 55 lumens K - Max 5 lumens LED source LED Osram Ostar RGBW - 5W Average LED life: 5. h Motors 5 (k & k), (k5) stepper motors, operating with microsteps, totally microprocessor controlled. Cooling High efficiency die-cast aluminium Forced ventilation Inputs DMX 5 8 (.6") (6.") 7 (8.86") 58 (.") 76 (8.7") 5 (.6") (.") 6 (.7") 58 (.") 5 (5.55") 6 (8.") Working position Functioning in any position. Movable body Movement by means of two stepper motors, controlled by microprocessor. Automatic repositioning of PAN and TILT after accidental movement not controlled by control unit. Travel: - PAN = 5 - TILT = 7 IP protection rating Protected against the entry of solid bodies larger than mm (.7 ). No protection against the entry of liquids. CE Marking Complies with the following European Directives - 6/5/EC (LVD) - /8/EC (EMC) - /65/EU (RoHS). Weights K5: 7.55kg K:. kg K:. kg CAUSE AND SOLUTION OF PROBLEMS THE PROJECTOR WILL NOT SWITCH ON ELECTRONICS NON-OPERATIONAL DEFECTIVE PROJECTION REDUCED LUMINOSITY POSSIBLE CAUSES No mains supply. LED exhausted or defective. Signal transmission cable faulty or disconnected. Incorrect addressing. Fault in the electronic circuits. Lenses or reflector broken Dust or grease deposited. Check the power supply voltage. Call an authorised technician. Replace the cables. Check addresses (see instructions). Call an authorised technician. Call an authorised technician. Clean (see instructions). CHECKS AND REMEDIES PROBLEMS

20 CHANNEL FUNCTION K5 STANDARD EXTENDED EXTENDED RGBW CHAN- NEL CHANNEL MODE CHAN- NEL CHANNEL MODE CHAN- NEL CHANNEL MODE SHAPES CHAN- NEL Red Red fine Green Green fine Blue Blue fine White White fine CTO Macro colour Strobe Dimmer Dimmer Fine Pan Pan Fine Tilt Tilt Fine Function Reset Red Red fine Green Green fine Blue Blue fine White White fine CTO Macro colour Strobe Dimmer Dimmer Fine Pan Pan Fine Tilt Tilt Fine Function Reset Shape Selection Shape Speed Shape Smoothing Shape Red Shape Green Shape Blue Shape White Shape Intensity Background Intensity Shape Transition Shape Offset CHANNEL MODE Red Red fine Green Green fine Blue Blue fine White White fine CTO Macro colour Strobe Dimmer Dimmer Fine Pan Pan Fine Tilt Tilt Fine Function Reset Red LED Green LED Blue LED Red LED Green LED Blue LED Red LED Green LED Blue LED Red LED Green LED Blue LED Red LED 5 Green LED 5 Blue LED 5 Red LED 6 Green LED 6 Blue LED 6 Red LED 7 Green LED 7 Blue LED 7 Red Red fine Green Green fine Blue Blue fine White White fine CTO Macro colour Strobe Dimmer Dimmer Fine Pan Pan Fine Tilt Tilt Fine Function Reset Red LED Green LED Blue LED White LED Red LED Green LED Blue LED White LED Red LED Green LED Blue LED White LED Red LED Green LED Blue LED White LED Red LED 5 Green LED 5 Blue LED 5 White LED 5 Red LED 6 Green LED 6 Blue LED 6 White LED 6 Red LED 7 Green LED 7 Blue LED 7 White LED 7

21 K STANDARD EXTENDED CHAN- NEL Red Red fine Green Green fine Blue Blue fine White White fine CTO Macro colour Strobe Dimmer Dimmer Fine Pan Pan Fine Tilt Tilt Fine Function Reset Zoom CHANNEL MODE CHAN- NEL CHANNEL MODE Red Red fine Green Green fine Blue Blue fine White White fine CTO Macro colour Strobe Dimmer Dimmer Fine Pan Pan Fine CHAN- NEL CHANNEL MODE Blue LED Red LED Green LED Blue LED Red LED Green LED Blue LED Red LED Green LED Blue LED Red LED Green LED Blue LED Red LED 5 Green LED 5 Tilt 65 Blue LED 5 7 Tilt Fine 66 Red LED 8 Function 67 Green LED Reset 68 Blue LED Zoom 6 Red LED 7 Red LED 7 Green LED 7 Green LED 7 Blue LED 7 SHAPES Blue LED Red LED 7 7 Red LED 8 Green LED 8 CHAN- NEL Red Red fine Green Green fine Blue Blue fine White White fine CTO Macro colour Strobe Dimmer Dimmer Fine Pan Pan Fine Tilt Tilt Fine Function Reset Zoom Shape Selection Shape Speed Shape Smoothing Shape Red Shape Green Shape Blue Shape White Shape Intensity Background Intensity Shape Transition Shape Offset CHANNEL MODE Green LED Blue LED Red LED Green LED Blue LED Red LED Green LED Blue LED Red LED 5 Green LED 5 Blue LED 5 Red LED 6 Green LED 6 Blue LED 6 Red LED 7 Green LED 7 Blue LED 7 Red LED 8 Green LED 8 Blue LED 8 Red LED Green LED Blue LED Red LED Green LED Blue LED 8 Red LED Green LED Blue LED Continue

22 K EXTENDED RGBW CHAN- NEL CHANNEL MODE CHAN- NEL CHANNEL MODE Red Red fine Green Green fine Blue Blue fine White White fine CTO Macro colour Strobe Dimmer Dimmer Fine Pan Pan Fine Tilt Tilt Fine Function Reset Zoom Red LED Green LED Blue LED White LED Red LED Green LED Blue LED White LED Red LED Green LED Blue LED White LED Red LED Green LED Blue LED White LED Red LED 5 Green LED 5 Blue LED 5 White LED 5 Red LED 6 Green LED 6 Blue LED 6 White LED 6 Red LED 7 Green LED 7 Blue LED 7 White LED Green LED 8 Blue LED 8 White LED 8 Red LED Green LED Blue LED White LED Red LED Green LED Blue LED White LED Red LED Green LED Blue LED White LED Red LED Green LED Blue LED White LED Red LED Green LED Blue LED White LED Red LED Green LED Blue LED White LED Red LED 5 Green LED 5 Blue LED 5 White LED 5 Red LED Green LED Blue LED White LED Red LED 7 Green LED 7 Blue LED 7 White LED 7 Red LED 8 Green LED 8 Blue LED 8 White LED 8 Red LED Green LED Blue LED White LED Red LED 8

23 K STANDARD EXTENDED CHAN- NEL SHAPES CHAN- NEL Red Red fine Green Green fine Blue Blue fine White White fine CTO Macro colour Strobe Dimmer Dimmer Fine Pan Pan Fine Tilt Tilt Fine Function Reset Zoom Red Red fine Green Green fine Blue Blue fine White White fine CTO Macro colour Strobe Dimmer Dimmer Fine Pan Pan Fine Tilt Tilt Fine Function Reset Zoom Shape Selection Shape Speed Shape Smoothing Shape Red Shape Green Shape Blue Shape White Shape Intensity Background Intensity Shape Transition Shape Offset CHANNEL MODE CHANNEL MODE CHAN- NEL Red Red fine Green Green fine Blue Blue fine White White fine CTO Macro colour Strobe Dimmer Dimmer Fine Pan Pan Fine Tilt Tilt Fine Function Reset Zoom Red LED Green LED Blue LED Red LED Green LED Blue LED Red LED Green LED Blue LED Red LED Green LED Blue LED Red LED 5 Green LED 5 Blue LED 5 Red LED 6 Green LED 6 Blue LED 6 Red LED 7 Green LED 7 Blue LED 7 Red LED 8 Green LED 8 Blue LED 8 Red LED Green LED Blue LED Red LED Green LED Blue LED Red LED Green LED Blue LED Red LED Green LED Blue LED Red LED Green LED Blue LED Red LED Green LED Blue LED Red LED 5 Green LED 5 Blue LED 5 Red LED CHANNEL MODE CHAN- NEL Green LED Blue LED Red LED 7 Green LED 7 Blue LED 7 Red LED 8 Green LED 8 Blue LED 8 Red LED Green LED Blue LED Red LED Green LED Blue LED Red LED Green LED Blue LED Red LED Green LED Blue LED Red LED Green LED Blue LED Red LED Green LED Blue LED Red LED 5 Green LED 5 Blue LED 5 Red LED 6 Green LED 6 Blue LED 6 Red LED 7 Green LED 7 Blue LED 7 Red LED 8 Green LED 8 Blue LED 8 Red LED Green LED Blue LED Red LED Green LED Blue LED Red LED Green LED Blue LED Red LED Green LED Blue LED Red LED Green LED Blue LED Red LED Green LED Blue LED Red LED 5 Green LED 5 Blue LED 5 Red LED 6 Green LED 6 Blue LED 6 Red LED 7 Green LED 7 Blue LED 7 CHANNEL MODE Continue

24 K EXTENDED RGBW CHAN- NEL CHANNEL MODE Red Red fine Green Green fine Blue Blue fine White White fine CTO Macro colour Strobe Dimmer Dimmer Fine Pan Pan Fine Tilt Tilt Fine Function Reset Zoom Red LED Green LED Blue LED White LED Red LED Green LED Blue LED White LED Red LED Green LED Blue LED White LED Red LED Green LED Blue LED White LED Red LED 5 Green LED 5 Blue LED 5 White LED 5 Red LED 6 Green LED 6 Blue LED 6 White LED 6 Red LED 7 Green LED 7 Blue LED 7 White LED 7 Red LED 8 Green LED 8 Blue LED 8 White LED 8 Red LED Green LED Blue LED White LED CHAN- NEL CHANNEL MODE Red LED Green LED Blue LED White LED Red LED Green LED Blue LED White LED Red LED Green LED Blue LED White LED Red LED Green LED Blue LED White LED Red LED Green LED Blue LED White LED Red LED 5 Green LED 5 Blue LED 5 White LED 5 Red LED Green LED Blue LED White LED Red LED 7 Green LED 7 Blue LED 7 White LED 7 Red LED 8 Green LED 8 Blue LED 8 White LED 8 Red LED Green LED Blue LED White LED Red LED Green LED Blue LED White LED Red LED Green LED Blue LED White LED Red LED Green LED Blue LED White LED Red LED Green LED Blue LED White LED CHAN- NEL CHANNEL MODE Red LED Green LED Blue LED White LED Red LED 5 Green LED 5 Blue LED 5 White LED 5 Red LED 6 Green LED 6 Blue LED 6 White LED 6 Red LED 7 Green LED 7 Blue LED 7 White LED 7 Red LED 8 Green LED 8 Blue LED 8 White LED 8 Red LED Green LED Blue LED White LED Red LED Green LED Blue LED White LED Red LED Green LED Blue LED White LED Red LED Green LED Blue LED White LED Red LED Green LED Blue LED White LED Red LED Green LED Blue LED White LED Red LED 5 Green LED 5 Blue LED 5 White LED 5 Red LED 6 Green LED 6 Blue LED 6 White LED 6 Red LED 7 Green LED 7 Blue LED 7 White LED 7

25 NOTE: On conclusion of resetting in case of absence of DMX signal, Pan & Tilt move to the "Home" position (Pan 5% - Tilt 5%) all the others channels stay at %. RED GREEN - BLUE - WHITE C.T.O. EFFECT 55 COLOUR INSERTED COLOUR EXCLUDED RED FINE GREEN FINE BLUE FINE WHITE FINE EFFECT EFFECT UNUSED RANGE Note: If CTO channel is active, the WHITE channel is disabled. 5 Continue

26 MACRO COLOUR STOP / STROBE LEE REFERENCE COLOUR Alice Blue Congo Blue Dark Steel Blue Deep lavender Lilac Tint Daylight Blue Flame Red Bastard Amber Deep Orange Pale Gold Apricot Bright Blue Primary Green Special lavender Pale Lavender Deep Golden Amber Medium Blue Bright Pink Mauve Dark Green Leaf Green Dark Blue Light Blue Steel Blue Med Blu Green Peacock Blue Magenta Dark Pink Middle Rose Light Salmon English Rose Light Rose Orange Deep Amber Straw Light Amber Spring Yellow Dark yellow green Just Blue Sky Blue Lavender Light Lavender Pink Carnation Medium Pink Light Pink Sunrise Red Dark Amber Gold Amber Medium Amber Fire Surprise Peach Straw Tint Medium Yellow Black White 5 K White 7 K White 7 K Magenta Yellow Cyan Blue Green Red Macro color OFF VALUE R G B W DIMMER DIMMER FINE (5 flash/sec) MACRO (,5 flash/sec) EFFECT 5-55 OPEN - 5 RANDOM FAST STROBE 6-8 RANDOM MEDIUM STROBE - 5 RANDOM SLOW STROBE 8 - OPEN 7 FAST PULSATION (5 flash/sec) 8 SLOW PULSATION - 7 OPEN FAST STROBE (5 flash/sec) SLOW STROBE ( flash/sec) - CLOSED 55 FULL LIGHT 55 NO LIGHT EFFECT EFFECT 6

27 PAN Operation with option InvertPan Off (Tilt conventionally represented at % and option Invert Tilt G TILT Operation with option InvertPan Off (Tilt conventionally represented at % and option Invert Tilt G GOff) GOff) Bit:.65 sec (K) -55 Bit:. sec (K) -55 Bit:. sec (K5) -55 Bit:.5 sec (K) -55 Bit:.87 sec (K) -55 Bit:.8 sec (K5) G G Operation with option InvertPan On (Tilt conventionally represented at % and option Invert Tilt Operation with option InvertPan On (Tilt conventionally represented at % and option Invert Tilt GOff) GOff) Bit:.5 sec (K) -55 Bit:.87 sec (K) -55 Bit:.8 sec (K5) -55 Bit:.65 sec (K) -55 Bit:. sec (K) -55 Bit:. sec (K5) TILT FINE Operation with option InvertPan Off (Tilt conventionally represented at % and option Invert Tilt PAN FINE Operation with option InvertPan Off (Tilt conventionally represented at % and option Invert Tilt G G GOff) G GOff) G Operation with option InvertPan On (Tilt conventionally represented at % and option Invert Tilt Operation with option InvertPan On (Tilt conventionally represented at % and option Invert Tilt GOff) GOff) Continue 7

28 FUNCTION EFFECT Reset to defult Unused Range Halogen Lamp Simulation, type 5 (5 W) Halogen Lamp Simulation, type ( W) Halogen Lamp Simulation, type ( W) Halogen Lamp Simulation, type ( W) Halogen Lamp Simulation, type (75W) Halogen Lamp Simulation OFF (Default) RGBW Gamma curve gamma =. RGBW Gamma curve gamma =.5 (Default) RGBW Gamma curve gamma =. Dimmer Curve Dimmer Curve (Default) Dimmer Curve Dimmer Curve Pan Tilt Normal Pan Tilt Fast (Default) Function off DIMMER CURVE - S The functions are actived passing through the unused range and staying 5 seconds in necessary level. Last selected function still active. Enable setting a new function. DIMMER CURVE - GAMMA LINEAR RESET 55 EFFECT COMPLETE RESET Complete reset is activated passing throug the unused range and staying 5 seconds in complete reset levels 8 7 COMPLETE RESET PAN / TILT RESET Pan / Tilt reset is activated passing throug the unused range and staying 5 seconds in Pan / Tilt reset levels PAN / TILT RESET ZOOM RESET Effects reset is activated passing throug the unused range and staying 5 seconds in Effects reset levels. 6 5 ZOOM RESET UNUSED RANGE DIMMER CURVE - GAMMA,5 * Automatic gamma is calculated based on background intensity to auto-adapt the shape s fade. DIMMER CURVE - GAMMA, 8

29 SHAPE SELECTION - SHAPE SPEED - SHAPE OFFSET SHAPE SELECTION On K5 On K On K RANDOM COLORS * SHAPE SPEED SHAPE OFFSET Reserved Two rotating arcs of different colors and direction Two rotating arcs of different colors Two rotating bars of different colors Triangle Half moon Bar ( arms) Fan ( arms) Rainbow, fixed speed with variable color offset. No No N.a. N.a. N.a. - = max to min speed, c.cw rotation 7-8 = STOP -55 = min to max speed, cw rotationt" - = c.cw rotation 7-8 = STOP -55 = cw rotationt N.a. -55 angle offset from to 6 N.a. Rainbow, variable speed. The value - or -55 change the rainbow angle offset (the orange starting angle). - = max to min speed, c.cw rotation 7-8 = STOP -55 = min to max speed, cw rotationt -55 angle offset from to 6 Random pixels with variable density and speed Random pixels distribuited on many fixtures - = max to min speed, Instant-on + fadeout. 7-8 = STOP. -55 = min to max speed, FadeIn + FadeOut. -55 select pixel density -55 select random distribution from up to fixtures Fade or snap depending on fade channel Ring with variable radius, filled. Ring with variable radius Ring Open/Close (close/open) Filled Ring Open/Close (close/open) Ring Opening (Closing) Filled Ring Opening (Closing) Ring + Ring + Ring + Ring Ring Ring Ring Macro OFF No No No No No No N.a. N.a. N.a. N.a. -55 = radius = minimum 55 = maximum - = max to min speed, Start closed 7-8 = STOP -55 = min to max speed, Start opened" - = max to min speed, Closing effect 7-8 = STOP -55 = min to max speed, Opening effect N.a. N.a. N.a. -55 angle offset from to 6 - continuous -55 random distribution of flash from to fixtures" N.a. N.a. *: Random colors activation with foreground R,G,B,W = Continue

30 Macro Off DMX channel value: from to 7. No shape effects activated. Turns off any previously selected shape. Static Rings DMX channel value: from 8 to. The ring or rings used by the macro are turned on with the foreground colour (Shape Red+Shape Green+Shape blue+shape White). Avaliable combinations: Ring On, Ring On, Ring On (Aleda K, K only), Ring On (Aleda K only),ring + On, Ring + On (Aleda K, K only), Ring + On (Aleda K only). Dynamic Rings DMX channel Dynamic Rings DMX channel value: From 5 to 8. The rings used by the macro are turned on sequentially, simulating an opening, closing or both. The Shape Speed channel increases the speed from (min speed) to (max speed) for the closing and closing/opening effects and from (min speed) to 55 (max speed) for the opening and opening/closing effects. With DMX value = 7 or 8 the macro stays still. The Shape Offset channel defines the macro effect distribution over a number of fixtures (affects also the behavior of a single fixture) Dmx values from to : continous distribution; Dmx values from to 55 random distribution of flash from to fixtures. If foreground colors are all set to, the Random-Colors mode is activated. The color used by the macro changes at every restart. Rings with variable radius DMX channel value: -. The Shape Speed channel defines the ring radius: = min, 55 = max. Random pixels DMX Random pixels DMX channel value:. Leds are turned on and off randomly. The Shape Speed channel increases the speed and defines the fade effect for the leds: from (min speed) to (max speed) with a Instant-on/ fade-out led effect, and from (min speed) to 55 (max speed)with a fade-in + fade-out led effect. At a DMX value of 7 and 8 the macro stays still. For macro the Shape Offset channel defines leds random distribution from ( fixtures) to 55 over a set of fixtures ( fixtures). For macro the Shape Offset channel defines pixels density from (min density) to 55 (max density). If foreground colors are all set to the Random-Colors mode is activated. The Shape Smoothing channel adjusts the fading effect applied to the macro movement Rainbows DMX channel value:. It simulates a rainbow effect. The Shape Speed channel increases the speed and defines the rotation : from (min speed) to (max speed) counter clock wise rotation and from (min speed) to 55 (max speed) clock wise rotation. With DMX value 7 or 8 the macro stays still. For the macro (Rainbow with fixed speed) the Shape Speed channel also defines angle offset (the orange sector starting angle). Rotating shapes DMX channel value: from 5 to. Shapes avaliable: Fan ( arms), Bar ( arms), Half Moon, Triangle, Two rotating bars of different colors, Two rotating arcs of different colors, Two rotating arcs of different colors and direction. The Shape Speed channel increases the speed and defines the rotation : from (min speed) to (max speed) counter clock wise rotation and from (min speed) to 55 (max speed) clock wise rotation. With DMX value 7 or 8 the macro stays still. The Shape Offset channel defines the angle offset from ( degree) to 55 (6 degree).

31 ZOOM SHAPE SMOOTHING 55 WIDE BEAM EFFECT EFFECT Smooth, fading curve with automatic gamma * Smooth, fading curve gamma Smooth, fading curve gamma, Smooth, fading curve gamma,86-55 Bit:.68 sec (K) -55 Bit:.6 sec (K) NARROW BEAM Smooth, fading curve gamma,5 Smooth, fading curve gamma,56 Smooth, fading curve gamma,5 Snap * Automatic gamma is calculated based on background intensity to auto-adapt the shape s fade. DMX Fading gamma SHAPE R G B W,5 55 EFFECT COLOUR INSERTED, Gamma Curve,,8,7 pixel power,6,5,,,, COLOUR EXCLUDED,,,,,,5,6,7,8,, pixel colour distribution DMX Fading gamma SHAPE INTENSITY,7 55 EFFECT COLOUR INSERTED,, Gamma Curve,8,7 pixel power,6,5,,,, COLOUR EXCLUDED,,,,,,5,6,7,8,, pixel colour distribution DMX Fading gamma BACKGROUND INTENSITY 55 EFFECT COLOUR INSERTED,, 5, Gamma Curve,8,7 pixel power,6,5,,,,,,,,,,5,6,7,8,, pixel colour distribution COLOUR EXCLUDED Continue

32 SHAPE TRANSITION FADING TIME FADING TIME FADING TIME FADING TIME 55 ms 6 ms 8 ms ms 5 7 ms 8 58 ms ms 86 6 ms 5 5 ms 7 56 ms ms 85 6 ms 5 ms 6 5 ms ms 8 6 ms 5 8 ms 5 5 ms ms 8 6 ms 5 86 ms ms 8 ms 8 6 ms 8 ms 7 ms 7 8 ms 8 5 ms 8 8 ms 5 ms ms 8 57 ms 7 78 ms ms 5 ms 7 56 ms 6 76 ms ms ms ms 5 7 ms 8 8 ms ms 77 5 ms 7 ms 88 6 ms ms 76 5 ms 68 ms 87 ms 8 ms 75 5 ms 65 ms 86 ms ms 7 5 ms 6 ms 85 ms ms 7 5 ms 6 ms 8 7 ms 8 ms 7 ms 57 ms 8 5 ms 7 ms 7 8 ms 8 55 ms 8 ms ms 7 7 ms 7 5 ms 8 ms 5 8 ms 6 6 ms 6 5 ms 8 ms ms 68 5 ms 5 7 ms 7 7 ms 5 ms 67 ms ms 78 5 ms ms 66 ms ms 77 ms ms 65 ms ms 76 ms ms 6 ms 7 ms 75 ms ms 6 ms ms 7 7 ms 8 7 ms 6 ms ms 7 5 ms 7 6 ms ms 8 ms 7 ms ms 5 7 ms 7 7 ms 7 ms 5 ms 58 6 ms 6 ms 7 8 ms ms 57 5 ms 5 ms 6 ms ms 56 ms ms 8 5 ms 8 ms 5-55 ms 7 ms 7 ms 7 ms 5 ms ms 6 ms 5 ms 5 ms ms 5 8 ms ms 5 ms ms 87 ms 8 ms -5 ms 7 ms 85 ms 7 ms 8 8 ms 8 5 ms 8 ms 6 ms 7 7 ms 7 ms 8 ms 5 88 ms ms ms 7 ms 87 ms 5 ms 5 7 ms 5 77 ms 86 ms - ms 5 ms ms 8 ms ms ms 57 7 ms 8 ms - ms ms 56 7 ms 8 ms 7-8 ms 88 ms 55 7 ms 8 ms 5-6 ms 86 ms 5 8 ms 8 7 ms ms 8 ms 5 6 ms 7 78 ms - 8 ms 8 8 ms 5 ms 6 77 ms - 7 ms 7 7 ms 5 ms 5 75 ms 7- ms 6 76 ms 5 ms 7 ms ms 5 7 ms 5 ms 7 ms - ms 7 ms 8 57 ms 7 ms - ms 6 ms 7 55 ms 7 ms -8 ms 67 ms 5 ms 6 ms -5 ms 65 ms 5 5 ms 8 68 ms 5- ms 6 ms 5 ms ms - No fade

33 K5 LED reference number for pixel mapping TILT: channel at 8% K LED reference number for pixel mapping TILT: channel at 8% 5 LED LED K LED reference number for pixel mapping TILT: channel at 8% LED

34

35 5

36 CLAY PAKY S.p.A. - Via Pastrengo, /b - 68 Seriate (BG) Italy - Tel Fax IST/ EN - Rev. /