LED-control Selection

Transcription

1 HighTech by that will save you time and money with the right tested combinations of Dimmer Driver Light source

2 Table of contents Page LED-control gears LCC8 Junior LCC9sc (synchronization and cascade connection) LCC LCC LCC60 MCM MultiControlModulePush, MCMP ControlModulePush 0/1-10Vdc, CMP LED-control gears and big loads EDL-system, Easy DALI-dimming of LED Projects (Restaurant Da Vinci, Office Tesla, Villa Maxwell) EDL-film Components Dimmable LED-drivers DIM350mA/18W DIM700mA/18W LED-dimmers UD LD LD LightKey LED-dimmers - Rotary type PWM 360A KED10VDA Du0 TM driving and dimming 12Vac LED Zero 35W Zero 70W Register 15 NOTE This document contains QR codes, to read these download a QR reader to your smartphone or tablet, then scan the QR code. You need access to the internet to access the material. All material is available at our website

3 LED control gear LCC8 Junior LCC8 Junior LED control gear LCC8 Junior (V D) A new addition in Vadsbo s series of LED-control gears. LED control gear LCC8 Junior is a combined LED driver and LED dimmer in one module for mounting in LED fixtures or a wall box. The saving potential with Box installation Dimmable with retractive switch or 1-10Vdc control signal. Designed for 350, 500 and 550mA constant current LED, max load 8W. New and easier way to install LED control gear LCC8 Junior is suitable for installation into standard wall boxes (wall box installation) behind the switch and simplifies installation and saves money compared to central installation. Central installation option means that the wiring is done from groups of light fittings and switches to the central control unit meaning long cables, more material and more work. Save money with Box installation With wall box installation of LCC8 Junior you can save a lot of money compared with central installation on cost of materials and labour. Wall box installation means less cables and simpler electrical circuiting. Power Range 1-8 W with 3 selectable DC currents LED control gear LCC8 Junior with output from 1-8W controls the most common constant current LEDs 350 ma along with 500 and 550 ma, selectable via DIP switch. LCC8 Junior can not be connected in series. Wiring Diagram Vdc 1-10 Vdc ON ON LED control gear LCC8 Junior V D For more information about LCC8 Junior scan the QR-code. Sync without a sync cable Up to 20 LCC8 Junior units can be controlled using the same retractive switch. No extra synchronization cable is required. The connection takes place on the primary side by parallel switching the control signal that is controlled by one or more reactive switches. L N S 2 1 LED LED + - L - N + S 2 1 Ideal size for build-into LED luminaires LED-control gear LCC8 Junior combines driver and dimmer in one extremely small unit with diameter 54 mm and height 22 mm. Its wall box shape and small size is a big advantage in installation. LED-control gear LCC8 Junior is ideally designed for mounting into LED fixtures where the space for LED-driver and dimmer is very limited. L N Vac 3

4 LED control gear LCC9sc LCC9sc LED control gear LCC9sc - now with synchronization and automatic cascading LED control gear LCC9 which is a patent-pending LED driver and dimmer for LED fixture or wall box has now been equipped with features for synchronization and cascading under the name LCC9sc. The new LED control gear LCC9sc is equipped with new features to sync without a sync cable and automatic cascading. LCC9sc drives up to 540W LED and controls with one retractive switch. Larger power range by automatic cascade connection Cascading means series connecting 2 or more units of LCC9sc to dim loads with higher power requirements than 9W. A group of 2 units will drive and dim: 10-18W A group of 3 units will drive and dim: 19-27W. Multiple control options LCC9 can be controlled by push (retractive switch) on the primary side and by push and 1-10 Vdc signal on the secondary side Synchronization Up to 20 groups (with up to 27W in each group) connected to LCC9sc units can be controlled using the same retractive switch. No extra synchronization cable is required. New sync function on the primary side You can synchronize up to 20 groups of LCC9sc on the primary side by parallel connection of the switching control signal which can be controlled by one or more retractive switches. New sync function on the secondary side With the updated version 3 pcs can be cascaded and synchronized automatically on the secondary side! Wide current and voltage range with 7 selectable DC currents and voltages LED control gear LCC9sc covers all commonly occurring currents and voltages such as 350, 500, 700 ma and 6, 9,12 and 24 Vdc selectable via DIP switch. Ideal size for build-in in LED lights LED control gear LCC9sc has a diameter of 56 mm and a height of 23 mm. Its box shape and small size is a big advantage in installation. LED control gear LCC9sc is thus ideally designed for mounting into LED fixtures where space for both driver and dimmer is very limited. Easy to install with wallbox installation LED control gear LCC9sc is suitable for installation into a standard wall box (box installation) behind the switch and simplifies the installation and saves money compared with central installation. Central installation option means that the wiring is done from light fittings and switches to the central control unit meaning long cables, more equipment and more work. Save time and money with box installation You can save a lot of money with box installation of LCC9sc compared with central installation in costs for materials and labor. Wall box installation means less cables and simpler electrical circuit. Up to 540W can be controlled by one swich LED control gear LCC9sc V D For more information about LCC9sc scan the QR-code Economic comparison between Box and Central installation. Save the Excel file from the home page. 4

5 LED control gears LCC30 and LCC60 LCC30 LED control gear LCC30 (V ) LCC30 is a perfectly matched LED-driver and LED dimmer in one unit for bigger LED-loads. It is able to sync without a sync cable. With LCC30 you will be able to drive up to 600W LED and dim the entire load from one retractive switch. It will satisfy the highest standards of simplicity, ease of use and thus customer satisfaction. Wider coverage of current and voltage range LED control gear LCC30 covers all commonly occurring currents and voltages selectable via DIP switches such as 350, 500, 700 and 900 ma and 12, and 24 Vdc. Control options LCC30 can be controlled by push (retractive switch) on the primary side and by 1-10 Vdc signal on the secondary side. Larger power range for constant current diodes LED control gear LCC30 has larger power range compared to commonly used options on the market. LCC30 Other options Diodecurrent Number of diodes Number of diodes 350mA 500mA 700mA 900mA 1-16 pcs 1W LED 1-15 pcs 2W LED 1-12 pcs 3W LED 1-7 pcs 4W LED 1-12 pcs 1W LED 1-12 pcs 1W LED 1-9 pcs 1W LED - Synchronization without sync-cable Up to 20 LCC30 can be controlled by a push button that can be through-connected from driver to driver and requires no external synchronization cable. It is therefore possible to power up to 600W of LED. Simultaneously controlled mixed loads It is possible to combine constant current fixtures (CC), constant voltage fixtures (CV) as well as popular LED stripes on LCC30 and get an overall smooth dimming by synchronizing the devices only through one push button. Easy to install in suspended ceiling LCC30 is equipped with simple throughconnection terminals for mains voltage 230 V as well as pushbutton control. The enclosure is designed with quicklocks on primary and secondary side and is equipped with sturdy quick connection terminals. Installation in suspended ceilings are made possible since LCC30 can be entered through a normal 70 mm hole. LED control gear LCC30 V LCC60 LED-control gear LCC60 (V ) LCC60 is a perfectly matched LED-driver and LED dimmer in one unit for bigger LED-loads. It is able to sync without a sync cable. With LCC60 you will be able to drive up to 1200W LED and dim the entire load from one retractive switch. It will satisfy the highest standards of simplicity, ease of use and thus customer satisfaction. Wider coverage of current and voltage range LED-control gear LCC60 covers all commonly occurring currents and voltages and is easily switchable between 350, 500, 700 and 900mA as well as 12 and 24Vdc. Control options LCC60 can be controlled by push (retractive switch) on the primary side and by 1-10 Vdc signal on the secondary side. Larger power range of constant current diodes LED controller LCC60 has larger power range, in comparison with commonly used alternatives on the market. Sync without a sync cable up to 1200W Up to 20 LCC60 can be controlled by a retractive switch that can be forward connected from unit to unit and requires no external synchronization cable. It is therefore possible to control up to 600W and 1200W LED with one retractive switch. Simultaneously mixed loads With the aid of common cabling multiple units can be synchronized. This means that you can set up one device at 12Vdc, 350mA at another, a third at 700mA and get them to run and dim synchronized with a single switch! You can thus operate and dim LED strips and LED fixtures simultaneously. Regardless of brand. Unique memory function The unique memory function means that you can turn on or off the light with for example motion detectors, twilight switches or timers. If the light is on in a specific dimmed mode and incoming voltage to LCC60 is broken there will be light in the last dimmed mode without any additional action by retractive switch when the power returns. This also means that, for example, when the fuse blows at home, light will return directly when the fuse has been restored. At the same time, you do not have to worry that the light will be on when you come home from vacation, for example, if in the meantime there has been a brief power outage. Individual outputs LCC60 has two outputs that are individually adjustable. You can run various LED types with the same control. LED control gear LCC60 V Quick Terminals Snap-lids Insertion of LCC30 in 70 mm hole. More information about LCC30 and LCC60 5

6 LED control gear LCC60 MCM LCC60 MCM Combined LED-driver and dimmer for DALI, DMX and Push LED-control gear LCC60MCM (V MCM) is a perfectly matched LED-driver and LED dimmer in one unit for multiple control options and bigger LED-loads. It is able to sync without a sync cable. With LCC60 you will be able to drive up to 1200W LED and dim the entire load from one retractive switch. It will satisfy the highest standards of simplicity, ease of use and thus customer satisfaction. Multiple Control options LCC60MCM can be controlled by push (retractive switch) on the primary side and by 1-10 Vdc signal on the secondary side as well as with DALI and DMX signals. DALI and DMX LCC60MCM which is equipped with Multi control module MCM can be controlled by DALI and DMX. The two outputs in the LCC60MCM can in a bus system be controlled individually. Each outlet can dim different types of LED. LCC60MCM gives a precise and accurate dimming. You can via the bus system choose exactly the dimmer level. In a bus system where twoway communication is supported it is possible to read the status of for example, the current voltage and current, or error status such as short circuit or if no load is connected. Wider current and voltage range LED-control gear LCC60MCM covers all commonly occurring currents and voltages and is easily switchable between 350, 500, 700 and 900mA as well as 12 and 24Vdc. Larger power of constant-current diodes LED controller LCC60MCM has a larger power range, in comparison with commonly used alternatives on the market. Sync without a sync cable up to 1200W Up to 20 LCC60MCM units can be controlled by a retractive switch that can be forward connected from unit to unit and requires no external synchronization cable. It is therefore possible to control up to 600W and 1200W LED with one push button. Simultaneously mixed loads Common cabling allows multiple units to be synchronized. This means that you can set up one unit at 12Vdc, another at 350mA and a third at 700mA and get them to run and dim synchronized with a single push button! You can therefore run and dim LED strips and LED luminaires simultaneously. Whatever the brands! Unique memory function The unique memory function means that you can turn on/ off the light with for example motion detectors, twilight switches or timers. If the light is on in a specific dimmed mode and incoming voltage to LCC60MCM is broken LCC60 MCM V MCM there will be light in the last dimmed mode without any additional action by retractive switch when the power returns. This also means that, for example, when the fuse blows at home, light will return directly when the fuse has been restored. At the same time, you do not have to worry that the light will be on when you come home from your vacation, if there in the meantime there has been a brief power outage. Individual outputs LCC60MCM has two outputs that are individually adjustable. You can run various LED types with the same control gear. Individually addressable outputs In a DALI or DMX environment the two outputs of LCC60MCM can be individually addressable by lighting group and by control unit. Loop-in/Loop-out Double terminals for quick and easy forwarding of phase, neutral and guide wire. Up to 20 units with a total power of 600W and 1200W can easily be controlled by a retractive switch. The units are connected together with standard installation cable via the extra control input. No special sync cable is required. Designation Art.Number Constant current (per output) Constant voltage (per output) Number of outputs 2 Dimming Bus control MCM Voltage primary Ambient temp. max (Ta) Test temp. (Tc) Dimension (LxWxH) Degree of protection LCC60 MCM V MCM 350mA (2-57V) 500mA (2-52V) 700mA (2-42V) 900mA (2-24V) 12Vdc 24Vdc For more information about MCM scan the QR-code 1-20W (1-16 psc LED Vf=3,6) 2-26W (1-14 psc LED Vf=3,6) 3-30W (1-11 psc LED Vf=3,6) 4-21W (1-6 psc LED Vf=3,6) 10,5W 21W Pushbutton, momentary, 1-10V, DALI, DMX Yes Vdc +50 C +75 C 220x62x34 mm IP20 6

7 MultiControlModulePush and ControlModulePush 0/1-10Vdc MultiControlModulePush, MCMP Dimmable LED control gears and dimmable ECGs are given advanced bus functions with MCMP. MultiControlModulePush MCMP supplies all operating units for lighting that is 0-10 or 1-10Vdc control with advanced bus functions. MultiControlModulePush is a totally outstanding and unique product. MCMP means in this context simplicity, ease of use and thus user satisfaction. Controlling with DALI and DMX All dimmable LED control gears for LED and dimmable electronic ballasts with 0-10VDC or 1-10VDC can now be controlled in a DALI or DMX environment, which creates unique opportunities in combination with the existing products on the market. MCMP currently supports DALI and DMX (and later KNX). MCMP regulates common 0-10Vdc or 1-10Vdc dimmable devices such as eg LED control gears and electronic ballasts. With control input for push dimming MCMP is equipped with a control input for push dimming where you can connect a momentary push button control. Box shape MCMP is made in box shape and can easily be placed in a junction box behind a push button. Low standby consumption The relay is of bistable type, which means that the relay only draws power when the switch changes position (on / off). This means that it doesn t develop any heat in the relay function. ControlModulePush 0/1-10Vdc, CMP Push-button control module 0/1-10Vdc is a new push button dimmer which aims to facilitate dimming of dimmable electronic ballast, LED control gears and electronic transformers with 1-10Vdc input. The unit is made in box shape and can easily be placed in a junction box behind a push button. Dimming without problems If you choose a 0/1-10Vdc push dimmer and a 0/1-10-Vdc LED control gear or electronic ballast they will work together smoothly regardless of the brand. Functions The ControlModulePush regulates common 0-10Vdc or 1-10Vdc dimmable units such as LED control gears and electronic ballasts. The ability to break the phase is there so you can switch on/off the units that are dimmable with 1-10Vdc. The control module is equipped with regulation of minimum dimming level and regulation of minimum dimming speed. Push dimming Push dimming has several advantages in terms of quick and easy dimming. A short press for on/off, a long press for dimming up/down. Push dimming is also convenient for the user who wants to control the light level from several different locations in the room - several buttons can control the same dimmer. Large groups You can easily provide a large group of eg LED control gears controlled by 1-10Vdc with quick and easy push dimming, which also can be dimmed from multiple locations, unlike traditional 1-10Vdc dimmers in rotary dimmer execution. Low stand-by consumption The relay is of bistable type, which means that the relay only draws power when the relay switches position (on/off). This means that it does not develop any heat in the relay and the relay keeps its settings even after a power failure. With memory function MCMP retains its position even after a power failure. Alternative possibilities MCMP are also able to break the phase to turn off / on the devices that are dimmable with 1-10Vdc. You can then choose if the pushbutton for example should guide 0/1-10Vdc regulation or any other device in the system you want to control. For more information about MCMP scan the QR-code For more information about CMP scan the QR-code Designation MCMP CMP Art.Number V-40010DCMCMP V-40010DCP Control inputs Controlled by one or more resilient snaps - DALI - DMX512 Outputs V V with bistable relay for switching function (Max 10A) - Max 100mA control signal Function - Adjustable between 0-10 or 1-10Vdc control - Memory Function Controlled by one or more resilient snaps V V with bistable relay for switching function (Max 10A) - Max 100mA control signal - Adjustable between 0-10 or 1-10Vdc control - Memory Function 7

8 LED control gears and big loads Sometimes you need to control bigger loads by a single control than only one LED control gear can handle. Depending on the type of LED control gear, there are some different ways to solve this Cascading 2 pcs LED control gear LCC9 are serially connected on the secondary side with the load. This enables that the total power of LED in a single series loop to be doubled. For example, if a LED control gear handles max. 9W load (equivalent to for example to 7 pcs of 350mA 1.2W LED) two pieces can be serially connected giving a total power of 18W, equivalent to eg 15 pcs of 350mA 1.2W LED in a loop. The control, whether it is a momentary switch or a 1-10Vdc control, is connected to the Master unit. The Master device is set to the constant current the LED lights are rated for and handles the constant current regulation of the light. The slave unit is set at a constant voltage and helps as a voltage boost circuit. How to set up the LED control gear is shown in the manual of the product. Cascading only works in constant current dimming. If the Master PWM regulates the current and you then connect a slave who is set to constant voltage out, there would be a conflict between them with an undesirable result as a consequence. The reason that you can not cascade connect 12 and 24Vdc constant voltage is because 12 and 24Vdc is PWM controlled. This means that you do not need any special sync cable and regular installation cable can be used. Running multiple LED control gears with the same switch Involves connecting the retractive switch to the control input of a LED control gear and then connecting the control inputs of the LED control gears with standard installation cable. (See figure below.) The total power in a single series loop is limited by the maximum power of the- LED control gear. The total power of a single control is limited by the number of LED control gears that can be connected to a control and the maximum power of the LED control gear. For example, if the LED control gear can handle max 30W it is 30W which is the limit of a loop of constant current LED. If you then can connect 20 pieces of LED control gears to a retractive switch, the overall power of a control- loop is 20 pcs x 30W giving a total of 600W. It is still perfectly possible to connect several retractive switches in parallel to control the entire group of LED-control gears from different places. After the installation is completed, the system shall be synchronized the first time. If you do not synchronize, there may be that some devices will shut down while others switch on or dim uneven. Synchronization is performed by the following procedure using the retractive switch. 1. A long push (now, all LED control gear shall be lit). 2. A brief push (now, all LED control gear shall be off). 3. A long push until all LEDs are in their maximum position (the LED control gear starts from min. position and goes up to max. if you hold the button down). This means that you do not need any special sync cable and regular installation cable can be used. L N L L N S S L N S N L VAC S L N Slave LED DIP + +Switch S L N Master LED DIP + +Switch L N S L N S Controlling multiple LED control gear with same button 1-10Vdc Control Involves connecting a 1-10Vdc control module to the control input of the LED control gear. All LED control gears will then get the same control signal from a 1-10Vdc control(dimmer). The total power in a single series loop is limited by the maximum power of the LED control gear. The total power of a single control is limited by the number of LED control gears that can be connected to a control and the maximum power of the LED control gear. For example, if the LED control gear can handle max 30W it is 30W which is the limit of a loop of constant current LED. If you then can connect 20 pieces of LED control gears to a 1-10 Vdc dimmer, the overall power of a control-loop is 20 pcs x 30W giving a total of 600W. Cascade connection You can not connect multiple 1-10Vdc dimmers to the same control loop. Thus you can not dim light from different points with this solution. 8

9 EDL-system, Easy DALI-dimming of LED Vadsbo s EDL system consists of a number of components which - in a simple and user-friendly way - can be used to build a system with the basic lighting control functions of DALI for LED lighting without using a PC. The main components of the system is LED-control gear LCC60 MCM which drives and dims the most common LED types on the market and Multi Control module MCMP which controls and regulates all 0 or 1-10V controlled devices such as eg LED drivers. LCC60 MCM and MCMP can then together with the other control modules in the EDL system be controled by DALI using momentary switches, prespresence detec tion devices or by retractive switches that can easily be programmed for different scenarios. The simplicity of the EDL-system Simplicity is one of the most important aspects when Vadsbo are developing new products. DALI actuators tend normally to be set and configured via a computer interface. This means that you, from the start, don t have control of the address of a specific actuator nor where it is located. In the same way the control modules are manually set. This means that the EDL system can be easily installed and manually adjusted without having to use a computer with advanced software. Precise control You will also get a precise control directly over where each address is placed in the facility when you set it directly on the device and you do not have to identify this in retrospect. Of course, you can also address and do the grouping with for example software from a PC. Projects For detailed information of the EDL installations scan the QR-codes or visit Watch the EDL-film by scanning the QRcode Individually addressable outputs Individually adressable outputs Vadsbo has provided both LED control gear LCC60 MCM and MultiControlModule MCMP with manual adjustment of both the address and the group. The setting is made via 3 pcs of knobs. 1 for the group (0-15) and 2 pieces for the address (0-63). Lighting control office Tesla folder. Lighting control restaurant da Vinci folder. Lighting control villa Maxwell folder. The components of the EDL system - LCC9 - LCC30 - LCC60 - LCC60MCM - Control Module Push - Multicontrolmodule Push - LD220 - LD440 - motiondot - switchdot - scenedot - busdot LCC60 MCM (V MCM) Each output will have its own address in a DALI or DMX system and can be controlled individually. Address and group are easily set manually via three knobs on the device. LCC60MCM automatically detects if DALI signal or DMX signal is connected and thus the same knob can be used for both DALI and DMX setting. If the DALI signal is detected the knobs are used to set the DALI address and group, if DMX signal is detected the same knobs are used to set the DMX address and group. It goes without saying that the DALI address and group can be set by a computer if desired. This means that EDL is suitable for both the smaller and simpler system and the bigger advanced system where you want to set and control everything via a computer. MultiControlModulePush MCMP (V-40010DCMCMP) MCMP is a box-actuator for DALI / DMX to 0-10 or 1-10V. Setting for 0-10 or 1-10V can be set directly on the device. You can also set the DALI commands via a computer. Address and group is manually set via three knobs. MCMP automatically detects if DALI signal or DMX signal is connected and thus the same knob can be used for both DALI and DMX setting. If the DALI signal is detected the knobs are used to set the DALI address and group, if DMX signal is detected the same knobs are used to set the DMX address and group. It goes without saying that the DALI address and group can be set by a computer if desired. This means that EDL is suitable for both the smaller and simpler system and the bigger advanced system where you want to set and control everything via a computer. LCC60 MCM V MCM see page 6 MCMP V-40010DCMCMP see page 7 9

10 EDL-system motiondot (V-40MODOT) motiondot is an interface between a regular presence sensor or motion detector and DALI bus and can easily be placed in an wall box. The time delay is controlled by the motion detector. By presence lighting is activated to 100% and by absence lighting is set to a stand-by mode. Standby mode can be adjusted from fully off to 75% brightness. MotionDOT can be set to control a group of devices or all devices on the DALI bus. Setting is done manually with a knob. switchdot (V-40SWDOT) switchdot enables dimming up and down and provides an interface between a standard retractive switch and DALI bus and can easily be placed in an appliance box. For example, a double switch can be connected to the control module and a button dims up or switches on while the second button down dims or turns off. switchdot can be set to control an individual unit, group of units or all devices on the DALI bus. Setting is done manually with a knob. scenedot (V-40SCDOT) scenedot enables the function to store and recall up to four scenarios (home, away, cleaning, etc.). 4 buttons can be connected to the module, one for each scenario. For achieving optimum results using a 4-channel low voltage switch is recommended. Scenarios are easily stored in each scenario button, by holding the button down for about 10 seconds. scenedot can easily be placed in an appliance box. To memorize eg All off function on key 1 first all lighting groups are manually switched off with each unit s individual control. When all lights are switched off key 1 is pressed for 10 seconds. Confirmation of stored scenario is displayed by all lights flashing. Setting of - if only a specific group or if all devices on the bus must store scenarios - is done manually with a knob. You can also set which memory position (of 16 possible) each button corresponds to. LCC9sc V D see page 4 LCC60 V see page 5 LCC60 MCM V MCM see page 6 LCC30 V see page 5 busdot (V-30125DALI) busdot is a power supply for DALI bus and can deliver up to 125mA. As an example, a control gear consumes max 2mA and a control module max 6mA. MCMP V-40010DCMCMP see page 7 LD220 V IB see page 12 LD440 V IB see page 12 motiondot V-40MODOT scenedot V-40SCDOT switchdot V-40SWDOT busdot V-30125DALI 10

11 Dimmable LED-drivers Dimmable LED drivers which unlike LED control gears require an external dimmer for dimming have different dimming options. Most commonly used methods are standard leading-edge or trailing-edge dimmers or 1-10Vdc control. A LED driver can generally not be set for different types of LEDs. A LED-driver is adapted for a specific type of diode such as 350mA constant current or 12Vdc constant voltage. LED-driver for leading- or trailing- edge dimmers LED-drivers are primarily dimmed with usual leadingor trailing-edge dimmers. Dimming is made just like a normal electronic transformers for low voltage halogen. Several LED drivers can be connected in parallel to a dimmer where the limiting factor is the maximum power of the dimmer. However, one must not forget that rated power of the LED-driver refers to the power that can be fed to the LEDs. The power that is charged to the dimmer is higher. Usually, the efficiency of the LED driver is about 80 % which means that the actual load on the dimmer is about 25% more than the LEDs that are connected. Min. power of the dimmer Please note that the total power of LED-driver should exceed the minimum power of the dimmer in order not to have problems with dimming. Therefore, it is recommended to use dimmer LD 220/440 (see page 12) which is designed for LED and starts already from 1W. Constant current LED drivers, dimmable with leading or trailing edge Dimmable LED drivers for constant current are dimmed just as a traditional electronic transformer with leadingor trailing-edge dimmers. 2 models 350 and 700mA with power up to 18W. Universal push dimmer LD 220 V IB Universal push dimmer LD440 V IB Constant current 350mA Constant current 700mA Designation DIM350mA/18W DIM700mA/18W Power, max 5-18W 5-18W Input V V The constant current 350mA 700mA Voltage range 15-52Vdc 6-26Vdc Number of LEDs (Vf = 3.6 V) 5-14x1W 2-7x3W Ambient temperature (Ta) +50 C +50 C Test temperature (Tc) 90 C 90 C Dimming Front / rear Front / rear Dimension 115x45x29 mm 115x45x29 mm Degree of protection IP20 IP20 11

12 LED-dimmers UD100, LD220 and LD440 Universal push dimmers UD100, LD220 and LD440 Universal LED-dimmers for wallbox installation that starts at 1W A common problem - when dimming LED lamps and CFL lamps - is that conventional dimmers usually require a high minimum load of 50W, 35W or 20W, while low energy light lamps and LED lamps have a power range from 1W up to 20W. For dimming of these low energy lamps dimmers that can operate from 1W and up are required. Vadsbo s series of universal push dimmers starts already at 1 W for dimming of both lowpower lamps as well as electronic transformers, dimmable LED-drivers and incandescent lamps. Adjustable minimum dimming level Depending on the type of load that is connected to the dimmer, the dimmer s lowest dimming level can be adjusted to fit the load in question. The dimming characteristic is distinguished between different types of loads. This feature is perfect for use when there is mixed loads of different lamptypes including dimmable halogen and incandescent lights. It is also very handy if the user at some future date decides to switch from incandescent to 230 VAC dimmable LEDs. Then you need only adjust the lowest dimming level to the new load, instead of buying a new dimmer. Memory function Equipped with memory function that also remains after power failure. Download the LightKey 2014 Vadsbo tests the most common dimmable 230V LED on the market together with our dimmers and and summarizes the results in the annual LightKey! Designation UD 100 LD 220 LD 440 Art. number V IB V IB V IB Power 1-100W 1-200W 1-440W Voltage 230 V +/-10% 50 Hz 230 V +/-10% 50 Hz 230 V +/-10% 50 Hz Max current 0,96 A 0,96 A 0,96 A For dimming of - Dimmable 230V LED - Dimmable LED driver for phase control - Dimmable CFLs V halogen lamps - Electronic transformers - Incandescent light 1-100W 1-100W 1-100W 1-100W 1-100W 1-100W 1-200W 1-200W 1-200W 1-200W 1-200W 1-200W Has adjustable minimum dimming level Yes Yes Yes Memorises the last set brightness, even after power failure Yes Yes Yes With motion detection / twilight relay / timer Yes Yes Yes Is controlled up to 5 reactive toggle switches Yes Yes Yes With soft start Yes Yes Yes 1-440W 1-440W 1-440W 1-440W 1-440W 1-440W Dimension Ø56 H22 mm Ø56 H22 mm Ø56 H22 mm Higher capacity Wider dimming range Excellent test ratings Adjustable min. dimming level One dimmer can control up to 14 pcs of 230V 7W LED-lamps Wider dimming range, starts alredy at 1 W 0-100% dimming Highest ratings in tests of 25 leading brands of 230 V LED-lamps. Average rating 4,7 points out of lamps scoring 5 out of 5. Different minimum settings possible for LED-lamps and CFL. 12

13 LED-dimmers - Rotary type PWM 360A LED Dimmer PWM 360A solves the problems of dimming LEDs To avoid problems with shortened lifespan of LEDs and color shifts in the light and flicker when dimmed; pulse width modulated current (PWM) is required. LED dimmer PWM 360A works with pulse width modulated current (PWM) and dims constant voltage diodes from 1W to 360W with 12 Vdc and 24 Vdc power supply from 15 to 360W. Dimming LEDs from 1W... Light-emitting diodes are operating in low power range from 1W and up. Dimming of light sources with low power, necessitate dimmers that can operate from as low as 1W. PWM 360A solves dimming problems at these low loads.... to 360W For LED chandeliers or larger LED installations power requirements are higher. PWM 360A solves dimming problems at large loads of up to 360W.... even in combination with Busch Jaeger fronts PWM 360A can be combined with Busch Jaeger fronts in designs glass, aluminum, gray, anthracite and white. Dimmer System PWM 360A covers - LED Dimmer 360W (V ) for constant voltage diodes. - Power supplier in Vdc with power from 15W to 360W. - Busch Jaeger fronts in design glass, aluminum, gray, anthracite and white available from electrical wholesalers. Power supplies for driving e.g. PWM360 Power supplies in Vdc with power from 15W to 360W. Also for DIN-rail mounting. KED10VDA Rotary type 1-10V Control module (V-40010A20DC) KED10VDA is a 1-10 Vdc control module for contolling dimmable electronic ballasts, LED drivers and electronic transformers with 1-10Vdc input. Quiet operation with high efficiency. Max 10A Rotary type knob Protection against transients, overloads and overtemperature EMC approved Dimensions 84x84x45 mm Designation PWM 360A KED10VDA Art. number V V-40010A20DC Min Power 1W 0,1A Max Power 8, 10, 12, 15, 24Vdc 10A 120, 150, 180, 225, 360W Input 8-24Vdc Output 8-24 Vdc (PWM modulated) Maximum current 15A 10A For constant voltage diodes Yes Yes PWM 360A can be combined with Busch Jaeger fronts Capable of memorizing most recent light intensity Yes Rotary dimmer Yes Yes Colour White White Dimension 84x84x45 mm 84x84x45 mm Yes Power supplies for driving PWM360 13

14 Du0 TM driving and dimming 12Vac LED LD 220 ZERO VAC LED 100% 99% of dimmable of non-dimmable* A new concept in dimming of 12VAC LED The combination of LD ZERO, 0 Watt transformers - Du0 TM generates a unique profile of the phase angle control of 12 Vac LED lights. The result is that 100% of 12Vac dimmable LED lights and 99% of non-dimmable 12Vac LED lights are dimmed in an excellent manner. Additionally ZERO 35 + LD 220 fits in a wall-box! The first component of Du0 TM - UD100, LD220 and 440, universal low power dimmers Vadsbo s universal low-power LED- dimmers will excellently dim all types of light sources such as dimmable CFLs and LEDs from low power up to 440W. Depending on the power factor of each lamp over 20 pcs 9W 230Vac dimmable LED lights can be dimmed with LD 220 for example. The second component of Du0 TM - ZERO, 0 WATTs electronic transformers The 0 WATT transformers ZERO 35 and 70 starts already at 0W. ZERO 35 is made in box-shape and fits into a wall box which facilitates the installation work. A conventional dimmer switch that starts at 20-35W is unable to deliver enough low RMS voltage for low power LED lamps with power from 3W and up. The combination UD100/LD220/440 which starts already at 1W and ZERO W transformers starting at 0W provide the sufficiently low RMS voltage level. Dimmable LED lamps typically have a built-in PWM-like feature that allows them to be dimmed which is not the case with non-dimmable LED lights. Du0 TM emulates PWM dimming, so even non-dimmable LED lamps will be dimmed in an excellent manner. For more information about Zero scan the QR-code Universal push dimmer LD 220 V IB 0 WATT transformer ZERO 35 V RZ 0 WATT transformer ZERO 70 V Z 14

15 Item number Product Item number Page LED-control gears LCC8 Junior V D LCC9sc V D LCC V LCC V LCC60 MCM V MCM MultiControlModulePush, MCMP V-40010DCMCMP ControlModulePush 0/1-10Vdc, CMP V-40010DCP EDL-system, Easy DALI-dimming of LED LCC9sc V D LCC V LCC V LCC60MCM V MCM MultiControlModulePush MCMP V-40010DCMCMP ControlModulePush CMP V-40010DCP MotionDOT V-40MODOT SwitchDOT V-40SWDOT SceneDOT V-40SCDOT BusDOT V-30125DALI Dimmable LED-drivers DIM350mA/18W V D DIM700mA/18W V D LED-dimmers UD V IB LD V IB LD V IB LED-dimmers - Rotary type PWM 360A V KED10VDA V-40010A20DC Du0 TM driving and dimming 12Vac LED Zero 35W V RZ Zero 70W V Z The content on these pages are subject to copyright under the Berne Convention. None of the information material may be reproduced for external use or transmitted in any form without written permission from Vadsbo. Technical specifications are subject to change without notice. Data subject to change without notice. All our products have a 2 year guarantee. Editors: Sune Ågren, Johan Sandberg Layout and original: Teresia Ågren Printed by ***

16 Aröds Industriväg Hisings Backa Sweden Distributor: Phone Fax