Bulletin 1606-XLS 1606-XLE 1606-XLP Performance Single/Three-Phase

Transcription

1 Bulletin Product Overview Type Bulletin XLS XLE XLP Performance Single/Three-Phase Essential Single/Three-Phase Compact Single/Two-Phase Output Power... W... W W Input Voltage/ Primary, V AC Voltage Efficiency...%...%...% Output Voltage/ Secondary,,,, V DC,, V DC,...,,,, V DC Voltage Rated Output Current. A. A.. A Operating Temperature Range Non-Operating Temperature Range - + C > C with derating - + C > C with derating - + C - + C > C with derating Certifications culus, CE, GL, ATEX UL, CE, CSA, GL culus, CE, CSA, GL Standards Compliance Special Application Products Product Selection EN (Class B), EN (Class B), EN --, EN -- (A), EN -, UL, UL, RoHS, Class Div. EN (Class B), EN (Class B), EN --, EN -- (A), EN -, UL, UL, CAN/CSA C. No. -, RoHS, Class, Div. - Compact redundancy module for V DC - Buffer module for extended ride-through - Redundancy modules - Redundant power supplies - DC UPS - DC converter EN -, EN --, EN -- (A), UL, UL, CAN/CSA C. No., RoHS Class, Div. Page - Page - Page - -

2 Bulletin Selection Information Bulletin Quick mounting and connecting, innovative DIN-Rail mount, smallest in class UL Listed NEC Class ; Class, Div. ; Semi F; ODVA Approved Low inrush current limiting PFC Active or Passive Wide range input; auto select input Superior overload design (continuous current, no hiccup) NEC Class 'Limited Power' options Selectable operating mode (single/parallel) Superior efficiency and temperature rating Special Modules Brownout buffer, DC to DC converter, N+ redundancy, DC UPS Standards Compliance World-wide Certifications culus, CE, C-Tick, ATEX NEC Class SEMI F Compatible Class Div. (TA) ABS/GL/RINA (Marine) Certifications Table of Contents Product Sizing this page Quick Guide - Special Applications - Catalog Number Explanation - Product Selection - Specifications and Approximate Dimensions - Not all features apply to all power supplies; see individual power supply descriptions for specifics A more detailed list of performance specifications can be found at the Allen-Bradley web site How to Select a Bulletin Power Supply The Bulletin line of is designed with "reserve power" thereby eliminating the need to oversize your power supply to start high inrush loads. Steps to size a Power Supply. Determine the "Average" continuous current of the load and the typical inrush current.. Select a power supply where the rated load is at/or below the current of the device and the Peak Current is less than the short-circuit rating of the power supply. Notes: ReservePower will deliver up to % additional current continuously. PowerBoost will deliver % of rated current for up to s. Example: Application: Single Phase V input, V output, A continuous current with. A inrush current Solution: XLSE Cat. No. I RATED [A] I SHORT CIRCUIT ( C) [A] I POWER BOOST or I RESERVEPOWER [A] XLSE... XLSE. XLSE XLSE XLSE- XLSDNET. XLSDNET XLEE... XLEE XLEE Output Characteristic for XLSE ( A) Power Supply Output Voltage Output Current I RATED : A I SHORT CIRCUIT : > A I POWER BOOST :. A Products with ReservePower. Short circuit current values are temperature dependent for the selected product; i.e., the higher the ambient temperature, the lower the short circuit current. Hiccup Overload design. -

3 Bulletin Quick Guide/ Special Applications Quick Guide Bulletin (number from table) Power Supply Quick Guide... W W W... W... W W W W W W W...V XLPA XLPA...V XLPB...V -Ph XLPB XLPB XLPBQ XLPBQT XLPB XLB... V -Ph XLEB (+/-) and V XLPC...V -Ph...V -Ph/- Ph XLPE XLPE XLPEQ Special Applications XLPE XLPEZ XLD XLPEQ XLPEQT XLSE XLEE XLPE XLPE XLPE XLSE XLSEA XLEE XLEEC XLEEE XLEEN XLSE XLSEC XLEE XLEEP XLEEE XLEEN XLPE- XLPE- XLEE- XLE-C XLEE- XLSE XLSEA XLSEC XLSEE XLSE- XLSE-C XLSEE XLE- XLEDX- N XLSE-...V XLSG-...V -Ph XLPF XLPF XLEF XLSF XLSFE...V -Ph XLEF- XLSF- XLEMX -N XLSF- V Redundant XLDR XLDR XLDR DeviceNet XLEDNET XLSDNET XLSDNET Example: For a... Volt, -Phase, Watt power supply, the Cat. No. would be XLE-. Bulletin Number NEC Class ABS/GL Marine XLE XLEE All XLE Power Supplies XLP XLS XLPA XLPB XLPE XLPA XLPB XLPE XLPC XLPB XLPE XLPEZ XLPF XLPE XLPB XLPE- XLPE XLSDNET XLPA XLPB XLPE XLPA XLPE XLPC XLPE XLPEZ XLPE XLPB XLPE XLPF XLPRED ALL XLS Power Supplies Cat. No. XLSK does not have Hazardeous Location Rating. Hazardeous Location Rating, Class Div ODVA Requirements Conformal Coating ATEX All XLE Power Supplies XLEDNET XLEEC XLPA XLPB XLPE XLPA XLPB XLPE XLPB XLPE XLPEZ XLPE XLPB XLPE XLPE XLPRED All XLS Power Supplies XLSDNET XLSDNET XLSEC XLSE-C XLSE-C XLSEA XLSEA XLSEA -

4 Bulletin Catalog Number Explanation/Product Selection Catalog Number Explanation Important: The following cat. no. breakdown is for explanation purposes only. It is not a product configurator. Not all combinations of fields are valid product cat. nos. First, select the desired power supply using the Product Selection tables. Then, use this breakdown for verification and explanation only. XLP XLS XLE a Power Supply Type Compact family Performance family Essential family XLS E b Rated Output Watts W W W W W W W W W W W W W W W W W W Product Selection XLS Performance Single- and Three-Phase Single-Phase Output Power [W] Output Voltage Output Current [A] a b c d e A B C D E F G M C R P Z X E N A c Output Voltage V DC...V DC or... V DC Dual +/- and V DC V DC...V DC...V DC...V DC V DC d Special Functions Can be left blank Conformal coating Redundancy module Power factor correction Removeable Terminations Semi-Regulated Regional voltage; V AC input only Regional voltage; V AC input only ATEX Steady State Input Current / [V AC] e Multi-Phase Variations Can be left blank - Two phase - Three phase -C -H -N Three phase, conformal coating Three phase, input voltage V AC and...v DC Three phase, input voltage V AC -D...V - DC Only Note: Special output signals are only available with the W power supply. Parallel Operation DC OK Relay Cat. No. Input Voltage Input Circuit Protection../. Yes XLSE A Slow Blow Fuse or./. Yes XLSE Cat. No. -AC./. Yes XLSEA./. Yes XLSB./. Yes XLSE...V AC,./. Yes XLSEA...V DC A Slow Blow Fuse or./. Yes XLSEC Cat. No. -AC./. Yes XLSF./. Yes XLSK./. Yes XLSE./. Yes XLSEC..../. Yes XLSEA...V AC A Slow Blow Fuse or./. Yes XLSF...V AC, Cat. No. -AC....V DC./. Yes XLSG...V AC,...V DC /. Yes XLSEE Unit has internal (not accessible/replaceable) input fuse. Additional protection is not required if used on branch circuits UL test levels. Consult local codes and regulations for installation. The C suffix in the Cat. No. indicates that the product has conformal coating. The A suffix in the Cat. No. indicates that the product carries the ATEX rating. -

5 Bulletin Specifications/Approximate Dimensions Bulletin XLS XLSEE XLSE- XLSF- Output Volts/Watts V/ W V/ W V/ W Input Voltage (... Hz)...V AC,...V DC... V AC...V AC,...V DC Operational Range...V AC,...V DC...V AC, V DC...V AC,...V DC Hold-up Time ms ms ms Rated Input Current. A. A. A Efficiency typ..% typ..% typ..% Output Voltage...V...V...V Rated Output Current ReservePower (typ. s) A (@ V) A (@ V) A (@ V) A (@ V) A (@ V). A (@ V) A (@ V) A (@ V) A (@ V). A (@ V) A (@ V). A (@ V) Ripple/Noise < mv PP < mv PP < mv PP Operating Temperature Range (T amb ) - C...+ C Non-Operating Temperature Range - C...+ C Dimensions (W x H x D) x x mm x x mm x x mm Weight g g g Certifications/Standards,,,,,,, Special Features Class, DIv., ABS/GL/RINA (Marine) ) = CE, ) = UL (culus LISTED), ) = UL (curus), ) = CSA C., No., ) Safety standards = IEC/EN, EN, ) EMC standards = EN (Class B), EN (Class B), EN --, ) EMC standards = EN -- (A), EN -, ) ABS/GL/RINA (Marine) MTBF determined by Siemens norm SN at full load current and C Output Volts/ Watts Input Voltage (... Hz) [V AC] Operational Range [V AC] Hold-up Time Rated Input Current XLEE W.../....../... > ms > ms. A (V. A (V XLEE XLEEC W.../... XLEEE W XLEEN W > ms > ms. A (V. A (V > ms > ms. A. A XLEE W.../....../... > ms > ms A (V. A (V XLEEE W XLEEN W XLEEP W XLEF V...V/ W / /... > ms > ms. A A >ms >ms <. A (V)/ <. A (V) >ms >ms <. A (V)/ <. A (V) Efficiency typ. % typ. % typ. % typ..% typ. % typ.. % typ.. % typ. % typ. % Output Voltage...V...V Rated Output Current Ripple/Noise Operating Temperature Range (T amb ) Non-Operating Temperature Range MTBF. V. V V. V V V V. V < mv PP C, > C with derating C > hours V V A V. V Dimensions (W x H x D) x x mm x x mm x x mm Weight g g g g g g g g g Certifications/Standards,,,,,,, Special Features NEC Class ) = CE, ) = UL (culus LISTED), ) = UL (curus), ) = CSA C., No., ) Safety standards = IEC/EN, EN, ) EMC standards = EN (Class B), EN (Class B), EN --, ) EMC standards = EN -- (A), EN -, ) ABS/GL/RINA (Marine) MTBF determined by Siemens norm SN at full load current and C. Indicates conformal coating. - Preferred availability cat. nos. are bold.

6 Bulletin Functions Extensive Diagnostic & Monitoring Functions Protective Features: Wrong battery voltage (V instead of V) Wrong battery polarity Too high ambient temperature Output overload or output short-circuit A - Status LED (green): Ready: Battery is charged > %, no wiring failure is recognized, input voltage is sufficient and inhibit signal is not active. Charging: Battery is charging and battery capacity is below %. Buffering: Unit is in buffer mode. B - Diagnosis LED (yellow): Overload: Output has switched off, due to long overload in buffer mode or due to high temperatures. Replace battery: Indicates a battery which failed the battery quality test (SCH test). Battery should be replaced soon. Buffer time expired: Output has switched off due to settings of buffer time. The signal will be stored and displayed for minutes. Inhibit active: Indicates that buffering is disabled due to an active inhibit signal. C - Check wiring LED (red): Check wiring between DC UPS and battery, as well as the battery itself. Also indicates when input voltage is not in range. D - Adjustor: Buffer time limiter: User accessible switch which limits the maximum buffer time in a buffer event, to save battery capacity. End-of-charge voltage: User accessible potentiometer which sets the end-of-charge voltage. Adjust the potentiometer according to the expected battery temperature. Deep discharge (battery) protection Wrong polarity on input terminals Over-voltage protection (malfunctioning of the internal regulation loops) E - Signal contacts: Ready (contact -): Contact is closed when battery is charged more than %, no wiring failure is recognized, input voltage is sufficient, and inhibit signal is not active. Buffering (contact -): Contact is closed when unit is buffering. Replace battery (contact -): Contact is closed when input voltage is sufficient and battery quality test (SCH test) indicates a negative result, three times in a row. Inhibit input (contact &): The inhibit input disables buffering. In normal mode, a static signal is required. In buffer mode, a pulse with a minimum length of ms is required to stop buffering. The inhibit is stored and can be reset by cycling the input voltage. A B C D E Preferred availability cat. nos. are bold. -