R2868 Flame Detector Driver Board Usage (ACM A)
|
|
- Christina Dalton
- 5 years ago
- Views:
Transcription
1 R88 Flame Detector Driver Board Usage (ACM-9--A) Technical Specifications: Operating Voltage: DC.V~0V Operating Current: ma~0ma Max (Always On Condition) Power Safe Mode:.mA (When sensing circuit is off) Board Mechanical Dimensions: 80mm x 0mm Mounting Hole ( x.mm Diameter), mm away from each corner Operating Basics The driver board provides the necessary operating voltage for the Hamamatsu Flame Sensor (R88, DC 0V ± 0V) with a DC Input from.v~0v. It uses an isolation step up transformer to step up the input voltage from.v to DC 0V ± 0V. Under operating conditions, when the sensor detectes the ultravoilet radiations emitted from a flame within operating range (up to 7meters), an V (approximate) pluses will be generated from the Pulse Out pin, the period and amplitude of the pulses depends on various factors. Such as distance of the flame detected and the intensity of the ultravoilet radiations emitted. The stronger the ultravoilet radiations the shorter the pluse out period. Unlike the C70 Hamamatsu Driver board, the in-house design driver board does not processed the signal generated from the R88 Flame Sensor. It outputs raw pulses directly from the Sensor Output and the user can directly interface it to a microcontroller IO pin to further processed the signal based on User's Application, thus providing better control and flexibility in the design. The driver board is designed with power savings in mind. Taking into considerations that the driver board could be battery operated. When the Push Button (PB) is depressed (Power Savings is On), the power ON/OFF to the sensor circuit is automatically controlled by AND-gate circuit (On and Off timing is set by Resistor Rx & Ry, Default set to sec On, 7sec Off with Rx=ohms, Ry=Kohms, refer to
2 Schematics Attached). In general, when operating in power savings mode and the user application detects low to high transition from PLISE-OUT pin, user application can set a high (Logic '') to the REMOTE-TRI to always turn on the power to the sensor, which will override the on-off timing from the PWM circuit, else if the REMOTE- TRI is Low (Logic '0'). The supply to the sensor circuit is controlled by the AND gate Circuit. Power Savings Switch (PB) Depressed Not Depressed Function Descriptions Power Savings Mode NON-Power Savings Mode REMOTE-TRI PIN '0'-Power to R88 determined by AND Gate Circuit (Resistor Rx & Ry) ''-Power to R88 always ON Floating or permanently tied to GND, the power to R88 will always be determined by AND Gate Circuit. No Effect Power Savings Mode Descriptions Table GND Pins Label.V~0V REMOTE-TRI Pulse Out Invert Pulse Out Descriptions Connect to Supply Input -ve/gnd Connect to Supply Input +ve (.~0V DC, 00mA AC-DC Power Adapter) Controls the Power Savings Mode, only useful when PB is depressed. Logic '' Power Supply to Sensor Circuit is always ON Logic '0' Power Supply to Sensing Circuit depends on AND Gate circuit (ON/OFF timing depends on resistor value of Rx and Ry) Schmitt Trigger Circuit not mounted by default (IC U and C0), the voltage is always high when there is no ultravoilet radiations detected. When there is flame detected, there will be series of high to low transistion pulses, opposite of those from Pulse Out pin. When ultravoilet radiations is detected, series of pulses with Low to High Transistions. Normally Logic low when there is no flame detected. PB (Push Button) Select Power Savings Mode Depressed Power Savings ON Un-Drepressed Power Savings OFF Pins Functional Descriptions
3 D D C JP HEADER Vin REMOTE-TRIG SCHMITT-TRI-OUT PLUSE-OUT C 0uF V PB Power Save Mode Depress To Off Common Depress To On SW-PB (-PIN) U ELM98AA-S VIN GND R9 D N8 VOUT C7 0pF C 7uF V 7 UA 7AHC00 R 70K C8 nf UB 7AHC00 R b 8K N.C c Q PMBT e 7 T TRANS-TOKO D EU0 R 0R C 000pF 0VDC D EU0 R M C R K7 000pF 0VDC C9 000pF U R88 R U R88 PLUSE-OUT C B c e R K D Indication N90 Q b D8 N8 R c e D7 BAT R8 N90 Q b R REMOTE-TRIG D N8 D N8 C 00uF V Rx K Ry 8 C 00uF V UC 7AHC R M UD 7AHC00 R0 0R R U VDD LOGIC-GATES-TCS8F C0 VSS 70pF SCHMITT-TRI-OUT Component Not Mounted, Allows Inverted R88 Pulse B Specifications PWM ON OFF Time (a).v ~ 0V Input Rx Ry ON (Sec) OFF (Sec) (b) Operating Current ma 8K 7K (c) Power Saving Mode at.ma 7K 0 (d) PCB Size 80mm x 0mm K.8 0 K 0 K 7 A A Title Size Number B R88 Flame Detector Main Module Date: -Apr-009 Sheet of of File: C:\Project\Lightings\DIY Projects\R88 Flame Drawn Detector\FlameDetector.ddb By: Revision.0
4
5
6
Ocean Controls KT-5221 Modbus IO Module
Ocean Controls Modbus IO Module 8 Relay Outputs 4 Opto-Isolated Inputs 2 Analog Inputs (10 bit) 1 PWM Output (10 bit) 4 Input Counters Connections via Pluggable Screw Terminals 0-5V or 0-20mA Analog Inputs,
More informationDIY KIT 141. Multi-Mode Timer
INTRODUCTION No one can call themselves an electronics hobbyist unless they have built a timer. There are many tens of designs using a variety of new and sometimes old circuits. Witness the longest surviving
More informationIRT Eurocard. Type AG-738. Stereo Audio Phase / Failure Detector
I R T Electronics Pty Ltd A.B.N. 000 7 6 Hotham Parade, ARTARMON N.S.W. 06 AUSTRALIA National: Phone: (0) 7 Fax: (0) 7 International: +6 7 +6 7 Email: sales@irtelectronics.com Web: www.irtelectronics.com
More informationAN APPLICATION NOTE
AN1894 - APPLICATION NOTE VIPower: VIPer12A NON ISOLATED BUCK AND BUCK-BOOST CONVERTER REFERENCE BOARD P. LIDAK - R. HAUSER ABSTRACT Presented circuit can be used to produce a single, non isolated positive
More informationSF229 Low Power PIR Circuit IC For security applications
Low Power PIR Circuit IC For security applications Preliminary datasheet DESCRIPTION The SF229 is a low power CMOS mixed signal ASIC designed for battery powered security applications that are either hard
More informationbhi bhi Sound Engineering Solutions from bhi Sound Engineering Solutions NEDSP1061-PCB bhi ltd 22 Woolven Close Burgess Hill West Sussex RH15 9RR
Sound Engineering Solutions Page 24 bhi bhi ltd 22 Woolven Close Burgess Hill West Sussex RH15 9RR tel: +44 (0)845 217 9926 fax: +44 (0)845 217 9936 sales@bhi-ltd.co.uk www.bhi-ltd.co.uk Sound Engineering
More informationSQ-1000 Super Squelch
SQ000 Super Squelch SQ000 Super Squelch When supplied with discriminator audio the SQ000 will perform the operation of a Squelch Circuit, /CAS Generator, or a Repeater Maker. As quieting occurs, the SQ000
More informationAssembly Manual for VFO Board 2 August 2018
Assembly Manual for VFO Board 2 August 2018 Parts list (Preliminary) Arduino 1 Arduino Pre-programmed 1 Faceplate Assorted Header Pins Full Board Rev A 10 104 capacitors 1 Rotary encode with switch 1 5-volt
More informationPOLOLU DUAL MC33926 MOTOR DRIVER FOR RASPBERRY PI (ASSEMBLED) USER S GUIDE
POLOLU DUAL MC33926 MOTOR DRIVER FOR RASPBERRY PI (ASSEMBLED) DETAILS FOR ITEM #2756 USER S GUIDE This version of the motor driver is fully assembled, with a 2 20-pin 0.1 female header (for connecting
More informationKUBE Electronics AG. KUBE TR156 Universal PIR Circuit IC. For PIR Motion and Presence Detectors. Applications. Features
KUBE TR156 Universal PIR Circuit IC For PIR Motion and Presence Detectors All functions for a PIR detector are available in a single chip solution. It includes analog and digital circuitry and functions
More informationElectronic Components
Electronic Components Arduino Uno Arduino Uno is a microcontroller (a simple computer), it has no way to interact. Building circuits and interface is necessary. Battery Snap Battery Snap is used to connect
More informationELECTRONIC GIANT. EG3013 Datasheet. Half-Bridge Driver. Copyright 2012 by EGmicro Corporation REV 1.0
ELECTRONIC GIANT EG33 Datasheet Copyright 22 by EGmicro Corporation REV. EG33 datasheet Contents. Features... 2 2. General Description... 2 3. Applications... 2 4. Device Information... 3 4.. Pin map...
More informationThe Skiidometer. Hardware Description By: Adam Lee ; Etec474; Prof. Morton; WWU
The Skiidometer Hardware Description By: Adam Lee 04.26.2003; Etec474; Prof. Morton; WWU General Description The Skiidometer is a portable meter which serves as a digital companion on the ski slopes. By
More informationELECTRONIC GIANT. EG3012 Datasheet. Half-Bridge Driver. Copyright 2012 by EGmicro Corporation REV 1.0
ELECTRONIC GIANT EG32 Datasheet Copyright 22 by EGmicro Corporation REV. EG32 datasheet Contents. Features... 2 2. General Description... 2 3. Applications... 2 4. Device Information... 3 4.. Pin map...
More informationbhi bhi DSP Noise Cancelling Products DSP Noise Cancelling Products NEDSP1061-PCB bhi ltd PO Box 318 Burgess Hill West Sussex RH15 9NR
DSP Noise Cancelling Products bhi bhi ltd PO Box 318 Burgess Hill West Sussex RH15 9NR tel: +44 (0)845 217 9926 fax: +44 (0)845 217 9936 sales@bhi-ltd.com www.bhi-ltd.com DSP Noise Cancelling Products
More informationLSI/CSI LS7290 STEPPER MOTOR CONTROLLER. LSI Computer Systems, Inc Walt Whitman Road, Melville, NY (631) FAX (631)
LSI/CSI UL A800 FEATURES: LSI Computer Systems, Inc. 1 Walt Whitman Road, Melville, NY 114 (1) 1-0400 FAX (1) 1-040 STEPPER MOTOR CONTROLLER Controls Bipolar and Unipolar Motors Cost-effective replacement
More informationLaserPING Rangefinder Module (#28041)
Web Site: www.parallax.com Forums: forums.parallax.com Sales: sales@parallax.com Technical:support@parallax.com Office: (916) 624-8333 Fax: (916) 624-8003 Sales: (888) 512-1024 Tech Support: (888) 997-8267
More informationPCA9633DEMO User Manual. Overview
PCA9DEMO Overview The PCA9 Demo Board demonstrates the Philips PCA9 Fast Mode Plus -bit I²C LED Dimmer IC. Four LEDs are connected to the PCA9 and through individual pulse width modulation (PWM) of each
More informationStatus Tone Generator
Eclipse Series RF Technology rfinfo@rftechnology.com.au January 004 Status Tone Generator Operation and Installation This manual is produced by RF technology Pty Ltd 0/8 Leighton Place, Hornsby 077, Australia
More informationIS31LT3953_IS32LT3953 DEMO BOARD GUIDE
DESCRIPTION The IS31LT3953_IS32LT3953 is a DC-to-DC switching converter, which integrate an N-channel MOSFET to operate in a buck configuration. The device supply a wide input voltage between 4.5V and
More informationMTSD-3. Two-Tone Decoder. Manual Revision: Hardware Revision(s): 165C
MTSD-3 Two-Tone Decoder Manual Revision: 2010-08-27 Hardware Revision(s): 165C 1 SPECIFICATIONS Operating Voltage Operating Current Input Level Input Impedance Frequency Range MTSD-3A MTSD-3B Ringing Output
More informationUNIVERSITY OF NAIROBI DEPARTMENT OF ELECTRICAL &INFORMATION ENGINEERING INVERTER DRIVE CONTROL OF SYNCHRONOUS MOTORS
UNIVERSITY OF NAIROBI DEPARTMENT OF ELECTRICAL &INFORMATION ENGINEERING INVERTER DRIVE CONTROL OF SYNCHRONOUS MOTORS PROJECT NO: PRJ 075 PRESENTER: MAUKA N. CHRISTINE REG.NO: F17/2147/2004 SUPERVISOR :
More informationLSI Computer Systems, Inc Walt Whitman Road, Melville, NY (631) FAX (631)
LSI/CSI UL A3800 LSI Computer Systems, Inc. 235 Walt Whitman Road, Melville, NY 747 (63) 270400 FAX (63) 270405 TOUCH CONTROL STEP DIMMER LIHT SWITCH WITH AUTOMATIC AIN CONTROL (AC) March 2007 FEATURES:
More informationExamining and Modifying Marker Generator Output
Examining and Modifying Marker Generator Output 10/26/99 Chuck Olson, WB9KZY Jackson Harbor Press http://jacksonharbor.home.att.net jacksonharbor@att.net Recently, I received an email mentioning missing
More informationT6331A TE CH. Boost or SEPIC DC-DC Controller FEATURES GENERAL DESCRIPTION. Applications Handheld Electronics MR-16 Lighting Divice
Boost or SEPIC DC-DC Controller FEATURES Wide Input Voltage Range: 2.7V to 5.5V Boost or SEPIC DC-DC Mode Controller VDD Under Voltage Lockout Build in over voltage Protect SOP-8 and SOT-23-6 Lead-free
More informationApplication Note Radiation Hardened Point-of-Load Regulators, MHP8564 / 8565 / 8566 / 8567 LAN - 001
Application Note Point-of-Load Regulators, MHP8564 / 8565 / 8566 / 8567 LAN - 001 By Alan Tasker, Engineering Lead, Microsemi Hybrid Product Group Copyright 2012 Page 1 Introduction The MHP856X are a series
More informationMotor Control Development Kit
User s Manual, V 1.0, June 2003 Motor Control Development Kit A reference design for low voltage 3-phase AC induction and brushless DC motor control. Microcontrollers Never stop thinking. Revision History:2003-06
More informationPACKAGE LIST A : DIP 8 pin B : SOP 8 pin OUT VSS Date code Lot No. OP1N OP1P OP1O VDD PAD DESCRIPTION Pad No. Pad Name I/O Type Pad De
PIR Controller IC for LED Lamp Specification GENERAL DESCRIPTION The IC is a CMOS chip designed to PIR controller IC for DC LED lamp. It can use PHOTO transistor or CDS application. The chip built-in regulator
More informationST12 CODEC IR/RF Remote Control Encoder/Decoder IC 1. Overview
ST CODEC / Remote Control Encoder/Decoder IC. Overview ST CODEC is Radio Frequency and Infrared encoder/decoder IC for remote control applications having unique features and flexibility not available with
More information1MHz,30V/1.5A High Performance, Boost Converter
1MHz,30V/1.A High Performance, Boost Converter General Description The is a current mode boost DC-DC converter. Its PWM circuitry with built-in 1.A current power MOSFET makes this converter highly power
More informationAL3157 Evaluation Module
Device Features Dual-Mode 1x and 2x Charge Pump V IN Range: 2.7V to 5.5V Up to 300mA total drive capability: Three 30mA and One 210mA Channels Two Simple PWM Dimming Control Inputs 1.2 MHz Constant Switching
More informationEmbedded Systems. Oscillator and I/O Hardware. Eng. Anis Nazer First Semester
Embedded Systems Oscillator and I/O Hardware Eng. Anis Nazer First Semester 2016-2017 Oscillator configurations Three possible configurations for Oscillator (a) using a crystal oscillator (b) using an
More informationPower Pulse Modulator A High Performance Versatile Square Pulse Generator
Power Pulse Modulator A High Performance Versatile Square Pulse Generator Model: PWM-OCXi v2 Type: High Voltage, 9A, 500V, 1.5MHz, Active Protection Features and Specifications Advanced active voltage
More informationThe FMMT718 Range, Features and Applications
The Range, Features and Applications Replacing SOT89, SOT223 and D-Pak Products with High Current SOT23 Bipolar Transistors. David Bradbury Neil Chadderton Designers of surface mount products wishing to
More informationApplication Note 5394
HCNR00 and HCNR0 Applications in Motor Drive and Current Loop Application Note 9 Abstract This note covers operation and applications of the HCNR00 and HCNR0 highlinearity analog optocouplers. Internal
More informationSeries AMLDP-Z Up to 1000mA LED Driver
FEATURES: Click on Series name for product info on aimtec.com Up to 000mA LED Driver Models Single output Model Input Voltage (V) Step Down DC/DC LED driver Operating Temperature range 40ºC to 85ºC Constant
More informationCurrent-Mode PWM Multiple Output Flyback Converter
Introduction Current-Mode PWM Multiple Output Flyback Converter The Supertex evaluation board demonstrates the features of HV606 IC by presenting a DC/DC converter employing flyback technique to achieve
More informationPT8A3252/54 5LED Ceramic Heating Controller
Features Pulse trigger with high current for SCR Quickly Heating-Up and Quickly Lost-Heat- Recover External Adjustable to fit wide range heating plates External Adjustable to different TCR of sensors Full
More informationCONSONANCE. 4A, Standalone Li-ion Battery Charger CN3761. General Descriptions: Features: Pin Assignment: Applications:
4A, Standalone Li-ion Battery Charger CN3761 General Descriptions: The CN3761 is a PWM switch-mode lithium ion battery charger controller for 1 cell li-ion battery in a small package using few external
More informationMAC: - Support for Unicast, Multicast and Broadcast packets - Programmable pattern matching of up to 64 bytes within packet at user defined offset
User s manual ET-MINI ENCJ0 ET-MINI ENCJ0 ET-MINI ENCJ0 is a module that is designed to be intermediary connections between Microcontroller and Ethernet Network. It supports operation of Protocol TCP/IP
More informationSPECIFICATION EP 1000/1500/2000 Series
UNINTERRUPTIBLE POWER SYSTEM SPECIFICATION EP 1000/1500/2000 Series Page 1 of 28 1.0 Revision Summary REVISION SECTION DESCRIPTION Formal Release Page 2 of 28 Table of Contents 1. Introduction. 4 2. Block
More informationAS5x40/AS5x45. User Manual AS5x40/AS5x45-AB-v bit Rotary Position Sensor with Digital Angle (Interface), ABI, UVW and PWM output
User Manual AS5x40/AS5x45-AB-v2.1 AS5x40/AS5x45 10-bit Rotary Position Sensor with Digital Angle (Interface), ABI, UVW and PWM output www.ams.com Revision 1.4 / 09.08.2013 page 1/16 Table of Contents 1
More information2A 150kHz 40V Buck DC/DC Converter With Constant Current Loop. Features. General Description. Applications
Features Wide 4.5V to 40V Input Voltage Range Output Adjustable from 1.235V to 37V Minimum Drop Out 1.5V Fixed 150kHz Switching Frequency 2A Constant Output Current Capability Internal Optimize Power Transistor
More informationUser s Manual. ACPL-339J Isolated Gate Driver Evaluation Board. Quick-Start. Testing Either Arm of The Half Bridge Inverter Driver (without IGBT)
ACPL-339J Isolated Gate Driver Evaluation Board User s Manual Quick-Start Visual inspection is needed to ensure that the evaluation board is received in good condition. The default connections of the evaluation
More informationApplication Note CDIAN003
Application Note CDIAN003 CDI GaN Bias Board User s Guide Revision 4.0 February 20, 2015 Quick Start Guide Shown below are the essential connections, controls, and indicators for the GaN Bias Control Board.
More informationBAP1551 Gate Drive Board
Application Note and Datasheet for Half Bridge Inverters Figure 1: BAP1551 IGBT Gate Driver Board Patent Pending Introduction The BAP1551 Insulated Gate Bipolar Transistor (IGBT) Gate Drive Board (GDB)
More informationIS31LT3954_IS32LT3954 DEMO BOARD GUIDE
DESCRIPTION The IS31LT3954_IS32LT3954 is a DC-to-DC switching converter, which integrate an N-channel MOSFET to operate in a buck configuration. The device supply a wide input voltage between 4.5V and
More informationSP6003 Synchronous Rectifier Driver
APPLICATION INFORMATION Predictive Timing Operation The essence of SP6003, the predictive timing circuitry, is based on several U.S. patented technologies. This assures higher rectification efficiency
More informationSteven Mark s Toroidal Power Unit (TPU) TP900 - TPU PULSER. - A useful tool for TPU and other research
Steven Mark s Toroidal Power Unit (TPU) TP00 TPU PULSER A useful tool for TPU and other research Prepared by: Document Date: Revision: Darren Kozey (z_p_e) 00/AUG/0 TP00. TP00 TPU PULSER PREFACE After
More informationCM A LOW-NOISE PWM STEP-DOWN REGULATOR
CM78.5A LOW-NOISE PWM STEP-DOWN REGULATOR GENERAL DESCRIPTION The CM78 is a low-noise, pulse-width-modulated (PWM), DC-DC step-down converter. It powers logic and transmitters in small wireless systems
More informationPT8A3270/1/2/3/4/5/6/7 Heating Controller
Features Dual Voltage (120V/240V) operations Auto temperature control with NTC NTC open protection Multi mode LED indicator Proportional control Pulse trigger for high current SCR Internal Zener Auto Heating
More informationQUASAR PROJECT KIT # /24 HOUR GIANT CLOCK
This project was originally published in the electronics magazine, Silicon Chip, a few years ago. It is issued here as a kit with permission. Some modifications to the original published circuit and software
More informationELECTRONIC GIANT. EG3113 Datasheet. Half-Bridge Driver. Copyright 2017 by EGmicro Corporation REV 1.0
ELECTRONIC GIANT EG33 Datasheet Copyright 27 by EGmicro Corporation REV. EG33 datasheet Contents. Features... 2 2. General Description... 2 3. Applications... 2 4. Device Information... 3 4.. Pin map...
More informationLBI-31807D. Mobile Communications MASTR II REPEATER CONTROL PANEL 19B234871P1. Maintenance Manual. Printed in U.S.A.
D Mobile Communications MASTR II REPEATER CONTROL PANEL 19B234871P1 Maintenance Manual Printed in U.S.A. This page intentionally left blank 13 PARTS LIST 12 PARTS LIST LBI-31807 11 PARTS LIST 10 SCHEMATIC
More informationRX23T inverter ref. kit
RX23T inverter ref. kit Deep Dive October 2015 YROTATE-IT-RX23T kit content Page 2 YROTATE-IT-RX23T kit: 3-ph. Brushless Motor Specs Page 3 Motors & driving methods supported Brushless DC Permanent Magnet
More informationProduct Specification
Product Specification SCA620-EF8H1A SINGLE AXIS ACCELEROMETER WITH ANALOG INTERFACE The SCA620 accelerometer consists of a silicon bulk micro machined sensing element chip and a signal conditioning ASIC.
More informationAMBIENT LIGHT DETECTOR
LX1973A AMBIENT LIGHT DETECTOR TM Page 1 INTRODUCTION TO PRODUCT The LX1973A Evaluation Board is available from for evaluating the functionality and performance of the LX1973A ambient light sensor. The
More informationMS8891A. Application Note. 1 General product description. 2 Introduction to capacitive sensing
Application Note 1 General product description The integrated circuit MS8891A is an ultra-low power two channel capacitive sensor specially designed for human body detection. It offers two operating modes:
More informationHT7612 General Purpose PIR Controller
General Purpose PIR Controller Features Operating voltage: 3.3V ~ 5.5V Standby current typical 15A CDS input High noise immunity 40 second power-on delay 10 second high speed warm-up for test mode 1~3783
More informationR 2. Out R 3. Ctrl C 2
Design Project: Pulse-Width Modulation (PWM) signal generator This worksheet and all related files are licensed under the Creative Commons Attribution License, version 1.0. To view a copy of this license,
More informationRB01 Development Platform Hardware
Qualcomm Technologies, Inc. RB01 Development Platform Hardware User Guide 80-YA116-13 Rev. A February 3, 2017 Qualcomm is a trademark of Qualcomm Incorporated, registered in the United States and other
More informationThe Robot Builder's Shield for Arduino
The Robot Builder's Shield for Arduino by Ro-Bot-X Designs Introduction. The Robot Builder's Shield for Arduino was especially designed to make building robots with Arduino easy. The built in dual motors
More informationFrequently Asked Questions DAT & ZX76 Series Digital Step Attenuators
Frequently Asked Questions DAT & ZX76 Series Digital Step Attenuators 1. What is the definition of "Switching Control Frequency"? The switching control frequency is the frequency of the control signals.
More information24/48V Fan Driver/Controller With High-Side Drive
24/48V Fan Driver/Controller With High-Side Drive Features High-side drive allows use of tachs Direct interface to host controller Noise-immune linear speed control 4-bit digital speed control Operates
More informationECE 2010 Laboratory # 5 J.P.O Rourke
ECE 21 Laboratory # 5 J.P.O Rourke Prelab: Simulate the circuit used in parts 1 and 2 of the Lab and record the simulated results. Your Prelab is due at the beginning of lab and will be checked off by
More informationFM20VHIR FM20VVIR. RedLink Fiber Optic Receiver for Direct High Voltage Switching Preliminary Data Sheet DESCRIPTION FEATURES APPLICATIONS
FM0VHIR FM0VVIR RedLink Fiber Optic Receiver for Direct High Voltage Switching Preliminary Data Sheet DESCRIPTION This Firecomms RedLink receiver is based on a fully integrated photodiode with TIA, limiting
More informationRT8129AGQW Evaluation Board
High Efficiency Single Synchronous Buck PWM Controller Purpose The RT8129A integrates a Constant-On-Time (COT) PWM controller and MOSFET driver so that the external circuit is easily designed and the components
More informationS24SP series 60W Single Output DC/DC Converter
Model List Model Number Input Voltage (Range) Output Voltage Output Current Input Current (typ input voltage) Load Regulation Maxcapacitive Load (Cap ESR>=1mohm;Full Efficiency (typ.) load;5%overshoot
More informationCosemitech. Automotive Product Group. FEATURES and FUNCTIONAL DIAGRAM
FEATURES and FUNCTIONAL DIAGRAM AEC-Q100 automotive qualified Digital Omnipolar-Switch Hall Sensor Superior Temperature Stability Multiple Sensitivity Options (BOP / BRP): ±25 / ±15 Gauss; ±70 /±35 Gauss;
More informationSIGNAL LEVEL SENSOR SYSTEM
SIGNAL LEVEL SENSOR SYSTEM GENERAL DESCRIPTION The NJU7181 is a signal level sensor system IC. It sends a High flag to the microprocessor or other equipments whenever it detects the existence of the audio
More informationLED Field Strength Indicator Kit
LED Field Strength Indicator Kit Description The Field Strength Indicator kit from Qrpkits.com provides a visual way to monitor RF fields through the brightness of an LED. It will respond to RF fields
More informationMC4X15A Universal Motor Controller
MC4X5A Universal Motor Controller Revision.0 / 4.May.07 MC4X5A is a Motor Controller based on 4 separate half-bridge drivers capable of driving -4V @ 5A each. Peak current can be larger. The controller
More informationA8133 HIGH EFFICIENCY, HIGH POWER WHITE LED DRIVER 1MHz FREQUENCY, INTERNAL 2A MOSFET SWITCH
DESCRIPTION The is a boost DC-DC converter that delivers a regulated output current. The switches at a 1.0MHz constant frequency, allowing for the use of small value external inductor and ceramic capacitors.
More informationACPL-32JT, ACPL-C87AT
ACPL-JT, ACPL-CAT Evaluation Driver Board for Fuji M -in- IGBT Introduction This evaluation driver board is optimized for a Fuji M -in- Integrated Gate Bipolar Transistor (IGBT) module rated at 0V, 00A.
More informationSGM Channel PWM Dimming Charge Pump White LED Driver
GENERAL DESCRIPTION The SGM3145 is a high performance white LED driver. It integrates current sources and automatic mode selection charge pump. The part maintains the high efficiency by utilizing a 1 /1.5
More informationUT01VS50L Voltage Supervisor Data Sheet January 9,
Standard Products UT01VS50L Voltage Supervisor Data Sheet January 9, 2017 www.aeroflex.com/voltsupv The most important thing we build is trust FEATURES 4.75V to 5.5V Operating voltage range Power supply
More informationPIR sensor control chip
PIR sensor control chip Outline TT0001 is a CMOS chip designed to human infrared sensor control integrated circuits; it is a kind of high-performance sensor signal processing integrated circuit (IC) which
More informationLab 8: SWITCHED CAPACITOR CIRCUITS
ANALOG & TELECOMMUNICATION ELECTRONICS LABORATORY EXERCISE 8 Lab 8: SWITCHED CAPACITOR CIRCUITS Goal The goals of this experiment are: - Verify the operation of basic switched capacitor cells, - Measure
More informationC S Technology Ltd. cstech.co.uk. DTMF decoder kit with relay output, opto coupled input & Morse transpond.
C S Technology Ltd cstech.co.uk DTMF decoder kit with relay output, opto coupled input & Morse transpond. Our DTMF Opto decoder kit has one relay output offering clean contacts, and one Opto coupled input
More informationDatasheet. Features. General Description. Applications
Features Wide 4.5V to 40V Input Voltage Range 3.3V,5V,12V, and adjustable versions Output Adjustable from 1.23V to 37V Maximum Duty Cycle 100% Minimum Drop Out 1.5V Fixed 150KHz Switching Frequency 3A
More informationnrf905-evboard nrf905 Evaluation board PRODUCT SPECIFICATION GENERAL DESCRIPTION
nrf905 Evaluation board nrf905-evboard GENERAL DESCRIPTION This document describes the nrf905-evboard and its use with the Nordic Semiconductor nrf905 Single Chip 433/868/915MHz RF Transceiver. nrf905-
More informationUSER'S GUIDE FOR INSTALLATION AND OPERATION
MANUFACTURER OF: ANI Systems Voice Encryption Modules Mobile Data Tone Signaling Boards Manual # 000 March,999 USER'S GUIDE FOR INSTALLATION AND OPERATION MODEL ST0BGP Mobilecall Voice Encryption Module
More information16 Bit Micro Experimenter Assembly and Check out Instructions
16 Bit Micro Experimenter Assembly and Check out Instructions The kit you purchased that includes PCB, schematic, complete parts list and these assembly instructions. A top picture of the complete assembly
More informationPreLab 6 PWM Design for H-bridge Driver (due Oct 23)
GOAL PreLab 6 PWM Design for H-bridge Driver (due Oct 23) The overall goal of Lab6 is to demonstrate a DC motor controller that can adjust speed and direction. You will design the PWM waveform and digital
More informationACE732E. 6V/3.5A, Fast Response, Step-Down Converter
Description ACE732E belongs to a new breed of high frequency synchronous Step-Down converter that combines the advantages of voltage mode control and Constant-On-Time control. Its adaptive Constant-On-Time
More informationPower Pulse Modulator A High Performance Versatile Square Pulse Generator
Power Pulse Modulator A High Performance Versatile Square Pulse Generator Model: PWM-OCXi v2.2 Type: High Voltage, 9A, 340V, 1.5MHz, Active Protection Features and Specifications * Max current varies with
More informationRC Camera Control. User Guide v1.3 (RCCC v1.1) 11/7/2012
RC Camera Control User Guide v1.3 (RCCC v1.1) 11/7/2012 kristaps_r@rcgroups INTRODUCTION RC Camera Control board (RCCC) is multifunctional control board designed to for aerial photography or First Person
More informationMLX90255 Linear Optical Array
Application Note: MLX90 Demo Board The demo board described in this document facilitates the evaluation of the MLX90xx Linear Optical Arrays. The board provides the necessary timing and clock signals to
More informationAS5304 / General Description. 2 Features of the AS5304/-06 Evaluation Kit. Integrated Hall ICs for Linear and Off-Axis Rotary Motion Detection
S0 / -0 Integrated Hall ICs for Linear and Off-xis Rotary Motion Detection EVLUTION KIT OPERTION MNUL General Description This document describes the features and operation of the S0/-0 Evaluation Kit.
More informationRT9209/A. Synchronous Buck PWM DC-DC with Enable & PGOOD. Preliminary. Features. General Description. Applications. Ordering Information
Preliminary Synchronous Buck PWM DC-DC with Enable & PGOOD General Description The is a single power supply PWM DC-DC converter controller designed to drive N-Channel MOSFET in a synchronous buck topology.
More informationADK-2579 Quick Start Guide HI-2579 Dual Transceiver Signal Break-Out Board
ADK-2579 Quick Start Guide HI-2579 Dual Transceiver Signal Break-Out Board July 2017 QSG-2579 Rev. New Holt Integrated Circuits REVISION HISTORY Revision Date Description of Change QSG-2579 Rev. New 07-27-17
More informationImplementation and Design Considerations of High Voltage Gate Drivers Richard Herring, Application Engineer
Implementation and Design Considerations of High Voltage Gate Drivers Richard Herring, Application Engineer 1 What will I get out of this session? Purpose: This session presents the high voltage half bridge
More informationDIGITAL DIRECTION SENSING MOTION DETECTOR MANUAL
DIGITAL DIRECTION SENSING MOTION DETECTOR MANUAL DP-005 GLOLAB CORPORATION Thank you for buying our DP-005 Digital Direction Sensing Motion Detector The goal of Glolab is to produce top quality electronic
More informationK / K / K164208
K161004 / K162104 / K164208 DESCRIPTION K16xxxx is a 8-bit CPU based Voice chip series. It is manufactured with Standard CMOS process with embedded voice storage memory. It can store from 10 to 42sec voice
More informationPAM2421 EVB User Guide
EV Board User Guide AE Department 1. Revision Information PAM2421 Date Revision Description Comment 2011/09 V1.0 Initial Release 2. PAM2804 General Description The PAM2421 devices are high-performance,
More informationS24SE/S24DE series 30W Single/Dual Output DC/DC Converter
FEATURES Efficiency up to 89% Wide input range, 9V-36V Package with Industry Standard Pinout Package Dimension: 25.4 x25.4 x10.2mm (1.0 x1.0 x0.40 )(No HSK) Over voltage protection, hiccup mode Over current
More informationMLX83100 Automotive DC Pre-Driver EVB83100 for Brushed DC Applications with MLX83100
EVB83100 for Brushed DC Applications with MLX83100 Stefan Poels JULY 17, 2017 VAT BE 0435.604.729 Transportstraat 1 3980 Tessenderlo Phone: +32 13 67 07 95 Mobile: +32 491 15 74 18 Fax: +32 13 67 07 70
More informationLSI/CSI LS6506R LS6507R PIR SENSOR INTERFACE. LSI Computer Systems, Inc Walt Whitman Road, Melville, NY (631) FAX (631)
6506R0602091 LSI/CSI UL A3800 LS6506R LS6507R LSI Computer Systems, Inc. 1235 Walt Whitman Road, Melville, NY 11747 (631) 2710400 FAX (631) 2710405 FEATURES: Latching relay drive (LS6506R) LS6506R is suitable
More information16-bit Constant Current LED Driver with Error Detection
: _ENG_V11 Version Issue Date : 2008/05/08 File Name : _ENGpdf Total Pages : 20 16-bit Constant Current LED Driver with Error Detection 16-bit Constant Current LED Driver with Error Detection General Description
More informationIntroduction. Features. Applications
70-70/70P-707-70-70T/S/R-L Features Precision supply-voltage monitor -.V (70L/70, L, 70L/707) -.V (70M/70, M, 70M/70) -.0V (70T, T, 70T) -.9V (70S, S, 70S) -.V (70R, R/70P, 70R) -.V (70Z, Z, 70Z) -.0V
More information