Electronic Components

Size: px
Start display at page:

Download "Electronic Components"

Transcription

1 Electronic Components

2 Arduino Uno Arduino Uno is a microcontroller (a simple computer), it has no way to interact. Building circuits and interface is necessary.

3 Battery Snap Battery Snap is used to connect a 9 volt battery into a breadboard or Arduino.

4 Breadboard Breadboard are for connecting wires and components with out soldering.

5 Ceramic Capacitor Stores electrons like a battery but once power to the circuit is removed it will discharge all its electrons at once. Appearance Schematic Symbol

6 Electrolytic Capacitor Stores electrons like a battery but once power to the circuit is removed it will discharge all its electrons at once. It has two (2) leads called a cathode (c-) (cathode is denoted by a shorter lead or by symbols on the side of the capacitor) and an anode (a+). Appearance Schematic Symbol

7 DC Motor DC motors coverts electrical energy to mechanical energy.

8 Gels filters Gel filters (red, green and blue) are used to filter out different wavelengths of light.

9 H-Bridge H-bridge allow the control of the polarity of voltage applied to a motor.

10 Battery Is electrical storage device with electrochemical cells to produce electricity. Appearance Schematic Symbol

11 Jumpers Jumper wires connect components to each other on a breadboard.

12 LED s Stands for Light Emitting Diode. This is a special kind of diode that emits light when a current flows through it. It has two (2) leads called a cathode (c-) (denoted by a shorter lead ) and an anode (a+). Appearance Schematic Symbol

13 LCD Liquid Crystal Display LCD is a alphanumeric graphic display with 2 rows and with 16 characters.

14 Male Header Pins Male Header pins is to make a connection between two devises.

15 Optocoupler Optocoupler is used to connect two circuits that do not share a common power supply.

16 Piezo Piezo is used to detect vibrations and create noises.

17 Photocell A photocell will act like a variable resistor. As more light is shined on the photocell the lower the resistance it will have and the more electrons will flow through the circuit. Appearance Schematic Symbol

18 Potentiometer This is a variable resistor. It controls the flow of electrons through a circuit but allows the resistance to be changed/controlled from a resistance of 0 to a maximum value. Appearance Schematic Symbol or

19 Switch Push Button Break (interrupts) or connects (delivers) current to an electrical circuit. Appearance Schematic Symbol

20 Resistors Limits the amount of current flowing through a circuit by presenting opposition or resistance to the current flow. Appearance Schematic Symbol

21 Servo Motor Servo motor is a geared motor that can only turn 180 degrees and is controlled by electrical pulses.

22 Temperature Sensor Temperature Sensor is a switch that opens and closes based on temperature.

23 Transistors NPN (2N3904) Are used to amplify electricity. There are two types of transistors, a NPN transistor (Not Pointing In). Transistors have three leads, the Emitter (E), the Base (B) and the Collector (C). Appearance Schematic Symbol

24 Transistors PNP (2N3906) Are used to amplify electricity. There are two types of transistors, a PNP transistor (Pointing In). Transistors have three leads, the Emitter (E), the Base (B) and the Collector (C). Appearance Schematic Symbol

25 SCR Allows current to flow through it, only after a momentary positive voltage is applied to its gate. An SCR is like a diode in that it has an Anode and a Cathode, and allows current to flow through it only in one direction. If when the positive charge is removed from the gate the SCR will continue to conduct. Appearance Schematic Symbol

26 Diode A diode act like a one-way street, it will only allow current to only flow one way. A diode has a positive (anode+) end and a negative (cathode-) end. A band of color around it denotes the negative end of the diode. Appearance Schematic Symbol

27 Integrated circuits (IC) Integrated circuits have several of the components condensed into one unit such as transistors, diodes, resistors, etc.. Each lead of the IC 555 Timer is numbered. The number one lead is designated by the small circle impression in one corner. The numbers run sequential, as seen on the schematic symbol below. Appearance Schematic Symbol

Semiconductors, ICs and Digital Fundamentals

Semiconductors, ICs and Digital Fundamentals Semiconductors, ICs and Digital Fundamentals The Diode The semiconductor phenomena. Diode performance with ac and dc currents. Diode types: General purpose LED Zener The Diode The semiconductor phenomena

More information

1 Second Time Base From Crystal Oscillator

1 Second Time Base From Crystal Oscillator 1 Second Time Base From Crystal Oscillator The schematic below illustrates dividing a crystal oscillator signal by the crystal frequency to obtain an accurate (0.01%) 1 second time base. Two cascaded 12

More information

Introduction to Electronics and Breadboarding Circuits

Introduction to Electronics and Breadboarding Circuits Introduction to Electronics and Breadboarding Circuits What we're going to learn today: What is an electronic circuit? What kind of power is needed for these projects? What are the fundamental principles

More information

Embedded Systems. Oscillator and I/O Hardware. Eng. Anis Nazer First Semester

Embedded Systems. Oscillator and I/O Hardware. Eng. Anis Nazer First Semester Embedded Systems Oscillator and I/O Hardware Eng. Anis Nazer First Semester 2016-2017 Oscillator configurations Three possible configurations for Oscillator (a) using a crystal oscillator (b) using an

More information

CHAPTER SEMI-CONDUCTING DEVICES QUESTION & PROBLEM SOLUTIONS

CHAPTER SEMI-CONDUCTING DEVICES QUESTION & PROBLEM SOLUTIONS Solutions--Ch. 15 (Semi-conducting Devices) CHAPTER 15 -- SEMI-CONDUCTING DEVICES QUESTION & PROBLEM SOLUTIONS 15.1) What is the difference between a conductor and a semi-conductor? Solution: A conductor

More information

Objectives: Learn what an Arduino is and what it can do Learn what an LED is and how to use it Be able to wire and program an LED to blink

Objectives: Learn what an Arduino is and what it can do Learn what an LED is and how to use it Be able to wire and program an LED to blink Objectives: Learn what an Arduino is and what it can do Learn what an LED is and how to use it Be able to wire and program an LED to blink By the end of this session: You will know how to use an Arduino

More information

M328 version ESR inductance capacitance meter multifunctional tester DIY

M328 version ESR inductance capacitance meter multifunctional tester DIY M328 version ESR inductance capacitance meter multifunctional tester DIY About transistor Multifunction Tester: The tester uses 3.7V rechargeable lithium battery (battery model: 14500) powered portable

More information

Autonomous Robot Control Circuit

Autonomous Robot Control Circuit Autonomous Robot Control Circuit - Theory of Operation - Written by: Colin Mantay Revision 1.07-06-04 Copyright 2004 by Colin Mantay No part of this document may be copied, reproduced, stored electronically,

More information

12V Dimmer Kit, version 2

12V Dimmer Kit, version 2 12V Dimmer Kit, version 2 User Manual Description The 12V Dimmer Kit V2 is an especially efficient PWM (pulse-width modulation) controller for 12V loads up to 60 watts. It features a single dial control

More information

5v AC R. 12v. 1kohm. F=35KHz oscilloscope. 3 Final Project OFF. ON Toggle Switch. Relay 5v 2N3906 2N uF LM311. IR Detector +5v GND LED PNP NPN

5v AC R. 12v. 1kohm. F=35KHz oscilloscope. 3 Final Project OFF. ON Toggle Switch. Relay 5v 2N3906 2N uF LM311. IR Detector +5v GND LED PNP NPN 3 Final Project Diode 103 IR Detector OFF ON Toggle Switch IR Detector +5v Push Button IR 100uF LED + GND LDR C Preset R 7805 IN GND OUT Relay 5v + PNP 2N3906 1 Kohm NPN 2N3904 4 3 2 1 555 5 6 7 8 4 3

More information

SUBELEMENT T6 Electrical components: semiconductors; circuit diagrams; component functions 4 Exam Questions - 4 Groups

SUBELEMENT T6 Electrical components: semiconductors; circuit diagrams; component functions 4 Exam Questions - 4 Groups SUBELEMENT T6 Electrical components: semiconductors; circuit diagrams; component functions 4 Exam Questions - 4 Groups 1 T6A Electrical components: fixed and variable resistors; capacitors and inductors;

More information

Two Hour Robot. Lets build a Robot.

Two Hour Robot. Lets build a Robot. Lets build a Robot. Our robot will use an ultrasonic sensor and servos to navigate it s way around a maze. We will be making 2 voltage circuits : A 5 Volt for our ultrasonic sensor, sound and lights powered

More information

Basic Electronics Refresher

Basic Electronics Refresher Basic Electronics Refresher Current and Voltage Current is the rate of flowing electric charge in a conductor. Voltage is the potential difference (electric driving force) applied between two points to

More information

List of Items Available in the Laboratory the Lab

List of Items Available in the Laboratory the Lab List of Items Available in the Laboratory the Lab Category Component 555 Timer $0.30 5V Relay $3.50 74xxx Series IC Chip $0.30 Battery - 12V (rechargeable Lead-acid type) $16.00 Battery - 6V (rechargeable

More information

Index. n A. n B. n C. Base biasing transistor driver circuit, BCD-to-Decode IC, 44 46

Index. n A. n B. n C. Base biasing transistor driver circuit, BCD-to-Decode IC, 44 46 Index n A Android Droid X smartphone, 165 Arduino-based LCD controller with an improved event trigger, 182 with auto-adjust contrast control, 181 block diagram, 189, 190 circuit diagram, 187, 189 delay()

More information

IR add-on module circuit board assembly - Jeffrey La Favre January 27, 2015

IR add-on module circuit board assembly - Jeffrey La Favre January 27, 2015 IR add-on module circuit board assembly - Jeffrey La Favre January 27, 2015 1 2 For the main circuits of the line following robot you soldered electronic components on a printed circuit board (PCB). The

More information

Basic Electronics Course Part 2

Basic Electronics Course Part 2 Basic Electronics Course Part 2 Simple Projects using basic components Including Transistors & Pots Following are instructions to complete several electronic exercises Image 7. Components used in Part

More information

RC Servo Interface. Figure Bipolar amplifier connected to a large DC motor

RC Servo Interface. Figure Bipolar amplifier connected to a large DC motor The bipolar amplifier is well suited for controlling motors for vehicle propulsion. Figure 12-45 shows a good-sized 24VDC motor that runs nicely on 13.8V from a lead acid battery based power supply. You

More information

Basic Microprocessor Interfacing Trainer Lab Manual

Basic Microprocessor Interfacing Trainer Lab Manual Basic Microprocessor Interfacing Trainer Lab Manual Control Inputs Microprocessor Data Inputs ff Control Unit '0' Datapath MUX Nextstate Logic State Memory Register Output Logic Control Signals ALU ff

More information

Project Name: SpyBot

Project Name: SpyBot EEL 4924 Electrical Engineering Design (Senior Design) Final Report April 23, 2013 Project Name: SpyBot Team Members: Name: Josh Kurland Name: Parker Karaus Email: joshkrlnd@gmail.com Email: pbkaraus@ufl.edu

More information

ELEXBO A-Car-Engineering

ELEXBO A-Car-Engineering 1 Task: -Construct successively all schematic diagrams and describe your findings. -Describe also the differences between the previous electrical diagram. Construct this electrical circuit and describe

More information

TV Remote. Discover Engineering. Youth Handouts

TV Remote. Discover Engineering. Youth Handouts Discover Engineering Youth Handouts Electronic Component Guide Component Symbol Notes Amplifier chip 1 8 2 7 3 6 4 5 Capacitor LED The amplifier chip (labeled LM 386) has 8 legs, or pins. Each pin connects

More information

FABO ACADEMY X ELECTRONIC DESIGN

FABO ACADEMY X ELECTRONIC DESIGN ELECTRONIC DESIGN MAKE A DEVICE WITH INPUT & OUTPUT The Shanghaino can be programmed to use many input and output devices (a motor, a light sensor, etc) uploading an instruction code (a program) to it

More information

Circuit Board Assembly Instructions for Babuinobot 1.0

Circuit Board Assembly Instructions for Babuinobot 1.0 Circuit Board Assembly Instructions for Babuinobot 1.0 Brett Nelson January 2010 1 Features Sensor4 input Sensor3 input Sensor2 input 5v power bus Sensor1 input Do not exceed 5v Ground power bus Programming

More information

IFB270 Advanced Electronic Circuits

IFB270 Advanced Electronic Circuits IFB270 Advanced Electronic Circuits Chapter 11: Thyristors Prof. Manar Mohaisen Department of EEC Engineering Review of the Precedent Lecture To introduce several concepts on capacitance in amplifiers

More information

Lab no. 4 Bipolar Transistor (NPN and PNP)

Lab no. 4 Bipolar Transistor (NPN and PNP) Lab no. 4 Bipolar Transistor (NPN and PNP) Transistors are semiconductor devices that enable to control the flow of large current by much smaller current. Bipolar transistor consists of three areas of

More information

SPINE ROAD HIGH SCHOOL TECHNOLOGY TEST 2 GRADE 9 SEPTEMBER 2017 EXAMINER: MRS N GOVENDER MODERATOR: MR LUKIE TIME: 1 HOUR 30 MINUTES INSTRUCTIONS

SPINE ROAD HIGH SCHOOL TECHNOLOGY TEST 2 GRADE 9 SEPTEMBER 2017 EXAMINER: MRS N GOVENDER MODERATOR: MR LUKIE TIME: 1 HOUR 30 MINUTES INSTRUCTIONS SPINE ROAD HIGH SCHOOL TECHNOLOGY TEST 2 GRADE 9 SEPTEMBER 2017 EXAMINER: MRS N GOVENDER MODERATOR: MR LUKIE TIME: 1 HOUR 30 MINUTES INSTRUCTIONS 1. Answer all questions 2. Rule off after each question.

More information

ELECTRIC CIRCUITS AND ELECTRONICS

ELECTRIC CIRCUITS AND ELECTRONICS Circuitos eléctricos y electrónicos ELECTRIC CIRCUITS AND ELECTRONICS Technology, programming and robotics II Electric Circuitos circuits eléctricos and y electronics electrónicos AN ELECTRICAL CIRCUIT

More information

ESE141 Circuit Board Instructions

ESE141 Circuit Board Instructions ESE141 Circuit Board Instructions Board Version 2.1 Fall 2006 Washington University Electrical Engineering Basics Because this class assumes no prior knowledge or skills in electrical engineering, electronics

More information

Workshop Part Identification Lecture N I A G A R A C O L L E G E T E C H N O L O G Y D E P T.

Workshop Part Identification Lecture N I A G A R A C O L L E G E T E C H N O L O G Y D E P T. Workshop Part Identification Lecture N I A G A R A C O L L E G E T E C H N O L O G Y D E P T. Identifying Resistors Resistors can be either fixed or variable. The variable kind are called potentiometers

More information

Home Map Projects Construction Soldering Study Components Symbols Membership FAQ Links

Home Map Projects Construction Soldering Study Components Symbols Membership FAQ Links Home Map Projects Construction Soldering Study Components Symbols Membership FAQ Links Multimeters Choosing Digital Analogue Voltage & Current Resistance Diode Transistor Next Page: Resistance Also See:

More information

Low Voltage, High Current Time Delay Circuit

Low Voltage, High Current Time Delay Circuit Low Voltage, High Current Time Delay Circuit In this circuit a LM339 quad voltage comparator is used to generate a time delay and control a high current output at low voltage. Approximatey 5 amps of current

More information

Laboratory 6 Diodes and Transistors

Laboratory 6 Diodes and Transistors Laboratory 6 page 1 of 6 Laboratory 6 Diodes and Transistors Introduction In this lab, you will build and test circuits using diodes and transistors. You will use a number of different types of diodes,

More information

Component Testing Technical Manual

Component Testing Technical Manual Technical Manual Introduction: Digital multimeters can test a variety of electronic components. That s primarily what they re used for. Any technician worth their salt knows how to use a meter to test

More information

DIODE / TRANSISTOR TESTER KIT

DIODE / TRANSISTOR TESTER KIT DIODE / TRANSISTOR TESTER KIT MODEL DT-100K Assembly and Instruction Manual Elenco Electronics, Inc. Copyright 1988 Elenco Electronics, Inc. Revised 2002 REV-K 753110 DT-100 PARTS LIST If you are a student,

More information

ELECTRONICS AND ELECTRICITY

ELECTRONICS AND ELECTRICITY INTRODUCTION ELECTRONICS ND ELECTRICITY The science of Electronics and Electricity makes a very important contribution to our everyday existence. Electricity is concerned with the generation, transmission

More information

Lab 2: Blinkie Lab. Objectives. Materials. Theory

Lab 2: Blinkie Lab. Objectives. Materials. Theory Lab 2: Blinkie Lab Objectives This lab introduces the Arduino Uno as students will need to use the Arduino to control their final robot. Students will build a basic circuit on their prototyping board and

More information

The silicon controlled rectifier (SCR)

The silicon controlled rectifier (SCR) The silicon controlled rectifier (SCR) Shockley diodes are curious devices, but rather limited in application. Their usefulness may be expanded, however, by equipping them with another means of latching.

More information

Home Map Projects Construction Soldering Study Components 555 Symbols FAQ Links

Home Map Projects Construction Soldering Study Components 555 Symbols FAQ Links Home Map Projects Construction Soldering Study Components 555 Symbols FAQ Links Circuit Symbols Wires Supplies Output devices Switches Resistors Capacitors Diodes Transistors Audio & Radio Meters Sensors

More information

HANDS-ON LAB INSTRUCTION SHEET MODULE 3 CAPACITORS, TIME CONSTANTS AND TRANSISTOR GAIN

HANDS-ON LAB INSTRUCTION SHEET MODULE 3 CAPACITORS, TIME CONSTANTS AND TRANSISTOR GAIN HANDS-ON LAB INSTRUCTION SHEET MODULE 3 CAPACITORS, TIME CONSTANTS AND TRANSISTOR GAIN NOTES: 1) To conserve the life of the Multimeter s 9 volt battery, be sure to turn the meter off if not in use for

More information

Electronics. RC Filter, DC Supply, and 555

Electronics. RC Filter, DC Supply, and 555 Electronics RC Filter, DC Supply, and 555 0.1 Lab Ticket Each individual will write up his or her own Lab Report for this two-week experiment. You must also submit Lab Tickets individually. You are expected

More information

HAW-Arduino. Sensors and Arduino F. Schubert HAW - Arduino 1

HAW-Arduino. Sensors and Arduino F. Schubert HAW - Arduino 1 HAW-Arduino Sensors and Arduino 14.10.2010 F. Schubert HAW - Arduino 1 Content of the USB-Stick PDF-File of this script Arduino-software Source-codes Helpful links 14.10.2010 HAW - Arduino 2 Report for

More information

o What happens if S1 and S2 or S3 and S4 are closed simultaneously? o Perform Motor Control, H-Bridges LAB 2 H-Bridges with SPST Switches

o What happens if S1 and S2 or S3 and S4 are closed simultaneously? o Perform Motor Control, H-Bridges LAB 2 H-Bridges with SPST Switches Cornerstone Electronics Technology and Robotics II H-Bridges and Electronic Motor Control 4 Hour Class Administration: o Prayer o Debriefing Botball competition Four States of a DC Motor with Terminals

More information

Electronics, Sensors, and Actuators

Electronics, Sensors, and Actuators Electronics, Sensors, and Actuators 4/14/15 David Flicker BE107 Overview Basic electronics and components Sensors Actuators Electronics 101 Voltage, V, is fundamentally how much energy is gained or lost

More information

EXPERIMENT 5 CURRENT AND VOLTAGE CHARACTERISTICS OF BJT

EXPERIMENT 5 CURRENT AND VOLTAGE CHARACTERISTICS OF BJT EXPERIMENT 5 CURRENT AND VOLTAGE CHARACTERISTICS OF BJT 1. OBJECTIVES 1.1 To practice how to test NPN and PNP transistors using multimeter. 1.2 To demonstrate the relationship between collector current

More information

Electronics Review 1 Cornerstone Electronics Technology and Robotics II Week 1

Electronics Review 1 Cornerstone Electronics Technology and Robotics II Week 1 Electronics Review 1 Cornerstone Electronics Technology and Robotics II Week 1 Administration: o Prayer o Welcome back o Review Quiz 1 Review: o Reading meters: When a current or voltage value is unknown,

More information

555 Morse Code Practice Oscillator Kit (draft 1.1)

555 Morse Code Practice Oscillator Kit (draft 1.1) This kit was designed to be assembled in about 30 minutes and accomplish the following learning goals: 1. Learn to associate schematic symbols with actual electronic components; 2. Provide a little experience

More information

Introduction to Arduino HW Labs

Introduction to Arduino HW Labs Introduction to Arduino HW Labs In the next six lab sessions, you ll attach sensors and actuators to your Arduino processor This session provides an overview for the devices LED indicators Text/Sound Output

More information

Design and Technology

Design and Technology E.M.F, Voltage and P.D E.M F This stands for Electromotive Force (e.m.f) A battery provides Electromotive Force An e.m.f can make an electric current flow around a circuit E.m.f is measured in volts (v).

More information

Long Loopstick Antenna

Long Loopstick Antenna Long Loopstick Antenna Wound on a 3 foot length of PVC pipe, the long loopstick antenna was an experiment to try to improve AM radio reception without using a long wire or ground. It works fairly well

More information

LAB PROJECT 2. Lab Exercise

LAB PROJECT 2. Lab Exercise LAB PROJECT 2 Objective Investigate photoresistors, infrared light emitting diodes (IRLED), phototransistors, and fiber optic cable. Type a semi-formal lab report as described in the lab manual. Use tables

More information

Conventional transistor overview and special transistors

Conventional transistor overview and special transistors Conventional transistor overview and special transistors This worksheet and all related files are licensed under the Creative Commons Attribution License, version 1.0. To view a copy of this license, visit

More information

DC Motors. come in all shapes and sizes. You probably have 3-4 on you right now. the two motors in the kit

DC Motors. come in all shapes and sizes. You probably have 3-4 on you right now. the two motors in the kit DC otors come in all shapes and sizes the two motors in the kit You probably have 3-4 on you right now (cell vibrate, laptop fan, laptop dvd drive) When motors first came out, people thought we d just

More information

Musical Pencil. Tutorial modified from musical pencil/

Musical Pencil. Tutorial modified from  musical pencil/ Musical Pencil This circuit takes advantage of the fact that graphite in pencils is a conductor, and people are also conductors. This uses a very small voltage and high resistance so that it s safe. When

More information

DIODE / TRANSISTOR TESTER KIT

DIODE / TRANSISTOR TESTER KIT DIODE / TRANSISTOR TESTER KIT MODEL DT-100K 99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com Assembly and Instruction Manual Elenco

More information

Process Components. Process component

Process Components. Process component What are PROCESS COMPONENTS? Input Transducer Process component Output Transducer The input transducer circuits are connected to PROCESS COMPONENTS. These components control the action of the OUTPUT components

More information

School of Engineering Mechatronics Engineering Department. Experim. ment no. 1

School of Engineering Mechatronics Engineering Department. Experim. ment no. 1 University of Jordan School of Engineering Mechatronics Engineering Department 2010 Mechatronics System Design Lab Experim ment no. 1 PRINCIPLES OF SWITCHING Copyrights' are held by : Eng. Ala' Bata &

More information

Semiconductor 9/21/2015

Semiconductor 9/21/2015 Semiconductor Electronics 9/21/2015 Starting simple the diode. The diode is one of the simplest semiconductor devices. It is comprised of two layers of semiconductor. One is impregnated with an electron

More information

Axis Fuzz Kit Building Manual

Axis Fuzz Kit Building Manual Axis Fuzz Kit Building Manual Effect Pedal Kits: Axis Fuzz The Axis Fuzz Kit is based in the Roger Mayer Axis Fuzz, the effect pedal responsible for Jimi Hendrix sound in Axis Bold As Love. What else is

More information

Technician Licensing Class T6

Technician Licensing Class T6 Technician Licensing Class T6 Amateur Radio Course Monroe EMS Building Monroe, Utah January 11/18, 2014 January 22, 2014 Testing Session Valid dates: July 1, 2010 June 30, 2014 Amateur Radio Technician

More information

LEVEL A: SCOPE AND SEQUENCE

LEVEL A: SCOPE AND SEQUENCE LEVEL A: SCOPE AND SEQUENCE LESSON 1 Introduction to Components: Batteries and Breadboards What is Electricity? o Static Electricity vs. Current Electricity o Voltage, Current, and Resistance What is a

More information

Discrete Op-Amp Kit MitchElectronics 2019

Discrete Op-Amp Kit MitchElectronics 2019 Discrete Op-Amp Kit MitchElectronics 2019 www.mitchelectronics.co.uk CONTENTS Introduction 3 Schematic 4 How It Works 5 Materials 9 Construction 10 Important Information 11 Page 2 INTRODUCTION Even if

More information

introduction to Digital Electronics Install the Arduino IDE on your laptop if you haven t already!

introduction to Digital Electronics Install the Arduino IDE on your laptop if you haven t already! introduction to Digital Electronics Install the Arduino IDE 1.8.5 on your laptop if you haven t already! Electronics can add interactivity! Any sufficiently advanced technology is indistinguishable from

More information

Bill of Materials: Metronome Kit PART NO

Bill of Materials: Metronome Kit PART NO Metronome Kit PART NO. 2168325 The metronome kit allows you to build your own working electronic metronome. Features include a small speaker, flashing LED, and the ability to switch between several different

More information

Schematics for Breakout Examples

Schematics for Breakout Examples Schematics for Breakout Examples This document contains wiring diagrams and component lists for the examples. A diagram may be used for more than one example file. The corresponding files are listed for

More information

Ten Tec DDS Board Assembly Procedure

Ten Tec DDS Board Assembly Procedure 05 May 2014 Ten Tec DDS Board Assembly Procedure You will find a photo of a completed board at the end of these instructions. Refer it whenever clarification is required. 1. AD9835 Attachment If you purchased

More information

Electronics: Design and Build Training Session. Presented By: Dr. Shakti Singh Hazem Elgabra Amna Siddiqui

Electronics: Design and Build Training Session. Presented By: Dr. Shakti Singh Hazem Elgabra Amna Siddiqui Electronics: Design and Build Training Session Presented By: Dr. Shakti Singh Hazem Elgabra Amna Siddiqui Basic prototyping and measurement tools Breadboard basics Back View VCC GND VSS Breadboard basics

More information

T6A4. Electrical components; fixed and variable resistors, capacitors, and inductors; fuses, switches, batteries

T6A4. Electrical components; fixed and variable resistors, capacitors, and inductors; fuses, switches, batteries Amateur Radio Technician Class Element Course Presentation ti ELEMENT SUB-ELEMENTS Technician Licensing Class Supplement T Electrical/Electronic Components Exam Questions, Groups T - FCC Rules, descriptions

More information

The FMMT718 Range, Features and Applications

The FMMT718 Range, Features and Applications The Range, Features and Applications Replacing SOT89, SOT223 and D-Pak Products with High Current SOT23 Bipolar Transistors. David Bradbury Neil Chadderton Designers of surface mount products wishing to

More information

SPACE WAR GUN KIT MODEL K-10. Assembly and Instruction Manual. Elenco Electronics, Inc.

SPACE WAR GUN KIT MODEL K-10. Assembly and Instruction Manual. Elenco Electronics, Inc. SPACE WAR GUN KIT MODEL K-10 Assembly and Instruction Manual Elenco Electronics, Inc. Copyright 1989 Elenco Electronics, Inc. Revised 2001 REV-H 753210A PARTS LIST Contact Elenco Electronics (address/phone/e-mail

More information

Figure 1: Basic Relationships for a Comparator. For example: Figure 2: Example of Basic Relationships for a Comparator

Figure 1: Basic Relationships for a Comparator. For example: Figure 2: Example of Basic Relationships for a Comparator Cornerstone Electronics Technology and Robotics I Week 16 Voltage Comparators Administration: o Prayer Robot Building for Beginners, Chapter 15, Voltage Comparators: o Review of Sandwich s Circuit: To

More information

Raygun. Vector Weapon. projects. Raygun vector weapon. Build a mini analog sound-effects circuit. By Symetricolour. Time: 2 4 hours CosT: $15 $20

Raygun. Vector Weapon. projects. Raygun vector weapon. Build a mini analog sound-effects circuit. By Symetricolour. Time: 2 4 hours CosT: $15 $20 projects Raygun vector weapon Raygun Vector Weapon By Symetricolour Time: 2 4 hours CosT: $5 $20 Build a mini analog sound-effects circuit. Gregory Hayes 02 Materials» raygun Vector Weapon Kit item #MSVWP

More information

MAKEVMA502 BASIC DIY KIT WITH ATMEGA2560 FOR ARDUINO USER MANUAL

MAKEVMA502 BASIC DIY KIT WITH ATMEGA2560 FOR ARDUINO USER MANUAL BASIC DIY KIT WITH ATMEGA2560 FOR ARDUINO USER MANUAL USER MANUAL 1. Introduction To all residents of the European Union Important environmental information about this product This symbol on the device

More information

o Semiconductor Diode Symbol: The cathode contains the N-type material and the anode contains the P-type material.

o Semiconductor Diode Symbol: The cathode contains the N-type material and the anode contains the P-type material. Cornerstone Electronics Technology and Robotics I Week 16 Diodes and Transistor Switches Administration: o Prayer o Turn in quiz Review: o Design and wire a voltage divider that divides your +9 V voltage

More information

Lab 1 - Revisited. Oscilloscope demo IAP Lecture 2 1

Lab 1 - Revisited. Oscilloscope demo IAP Lecture 2 1 Lab 1 - Revisited Display signals on scope Measure the time, frequency, voltage visually and with the scope Voltage measurement* Build simple circuits on a protoboard.* Oscilloscope demo 6.091 IAP Lecture

More information

3a Switching Regulator Circuit Diagram Using Lm317

3a Switching Regulator Circuit Diagram Using Lm317 3a Switching Regulator Circuit Diagram Using Lm317 The following circuit diagram shows a way of powering a two-way mobile radio using the The LM317T is an adjustable 3-terminal positive voltage regulator

More information

Two-Tone Phototransistor Theremin Using a 556 Timer IC

Two-Tone Phototransistor Theremin Using a 556 Timer IC Two-Tone Phototransistor Theremin Using a 556 Timer IC BY CABE ATWELL Difficulty: Easy - Medium Build Time: 2-3 hours The Theremin is an electronic musical instrument with its roots in the dark world of

More information

Electrical, Electronic and Communications Engineering Technology/Technician CIP Task Grid

Electrical, Electronic and Communications Engineering Technology/Technician CIP Task Grid Secondary Task List 100 SAFETY 101 Describe OSHA safety regulations. 102 Identify, select, and demonstrate proper hand tool use for electronics work. 103 Recognize the types and usages of fire extinguishers.

More information

GuitarPCB.com Presents. Fuzzy Bee v2 (Pump d Up Edition) Build Instructions

GuitarPCB.com Presents. Fuzzy Bee v2 (Pump d Up Edition) Build Instructions GuitarPCB.com Presents Fuzzy Bee v2 (Pump d Up Edition) Build Instructions Board Dimensions (W x H) 2.13 x 1.67 i.e.: 54.0mm x 42.4mm. This design will fit into a 1290NS/1590B size enclosure or larger.

More information

Learn about the use, operation and limitations of thyristors, particularly triacs, in power control

Learn about the use, operation and limitations of thyristors, particularly triacs, in power control Exotic Triacs: The Gate to Power Control Learn about the use, operation and limitations of thyristors, particularly triacs, in power control D. Mohan Kumar Modern power control systems use electronic devices

More information

http://www.electronics-tutorials.ws/power/triac.html Triac Tutorial and Basic Principles In the previous tutorial we looked at the construction and operation of the Silicon Controlled Rectifier more commonly

More information

40106 Hex Oscillator Workshop Instructions. bbob drake, aka fluxmonkey

40106 Hex Oscillator Workshop Instructions. bbob drake, aka fluxmonkey 40106 Hex Oscillator Workshop Instructions bbob drake, aka fluxmonkey 40106 Hex Oscillator Workshop Instructions by Bbob Drake is licensed under a Creative Commons Attribution-ShareAlike 4.0 International

More information

Demon Pumpkin APPROXIMATE TIME (EXCLUDING PREPARATION WORK): 1 HOUR PREREQUISITES: PART LIST:

Demon Pumpkin APPROXIMATE TIME (EXCLUDING PREPARATION WORK): 1 HOUR PREREQUISITES: PART LIST: Demon Pumpkin This is a lab guide for creating your own simple animatronic pumpkin. This project encourages students and makers to innovate upon the base design to add their own personal touches. APPROXIMATE

More information

Experiment #3: Micro-controlled Movement

Experiment #3: Micro-controlled Movement Experiment #3: Micro-controlled Movement So we re already on Experiment #3 and all we ve done is blinked a few LED s on and off. Hang in there, something is about to move! As you know, an LED is an output

More information

DC Motor. Controller. User Guide V0210

DC Motor. Controller. User Guide V0210 DC Motor Controller User Guide 59757 V0210 This kit provides a great exercise of intermediate soldering skills and creates a device that enables you to control various Pitsco motors, Tamiya gearboxes,

More information

Unit/Standard Number. LEA Task # Alignment

Unit/Standard Number. LEA Task # Alignment 1 Secondary Competency Task List 100 SAFETY 101 Demonstrate an understanding of State and School safety regulations. 102 Practice safety techniques for electronics work. 103 Demonstrate an understanding

More information

Digital Electronics & Chip Design

Digital Electronics & Chip Design Digital Electronics & Chip Design Lab Manual I: The Utility Board 1999 David Harris The objective of this lab is to assemble your utility board. This board, containing LED displays, switches, and a clock,

More information

Circuit Board Assembly Instructions

Circuit Board Assembly Instructions Circuit Board Assembly Instructions This document walk you through the assembly of the Base4 Clock v1.2 - v1.3 circuit boards. Important note for kit buyers The color and appearance of the components may

More information

Electronics Merit Badge Kit Theory of Operation

Electronics Merit Badge Kit Theory of Operation Electronics Merit Badge Kit Theory of Operation This is an explanation of how the merit badge kit functions. There are several topics worthy of discussion. These are: 1. LED operation. 2. Resistor function

More information

555 Astable Kit MitchElectronics 2018

555 Astable Kit MitchElectronics 2018 555 Astable Kit MitchElectronics 2018 www.mitchelectronics.co.uk CONTENTS Introduction 3 Schematic 3 How It Works 4 Materials 6 Construction 7 Important Information 8 Page 2 INTRODUCTION The 555 timer

More information

Motors and Servos Part 2: DC Motors

Motors and Servos Part 2: DC Motors Motors and Servos Part 2: DC Motors Back to Motors After a brief excursion into serial communication last week, we are returning to DC motors this week. As you recall, we have already worked with servos

More information

Module 04.(B1) Electronic Fundamentals

Module 04.(B1) Electronic Fundamentals 1.1a. Semiconductors - Diodes. Module 04.(B1) Electronic Fundamentals Question Number. 1. What gives the colour of an LED?. Option A. The active element. Option B. The plastic it is encased in. Option

More information

D.I.Y L.E.D CUBE 4X4X4. Level: Intermediate

D.I.Y L.E.D CUBE 4X4X4. Level: Intermediate EN D.I.Y L.E.D CUBE 4X4X4 Level: Intermediate AK-125 TABLE OF CONTENTS Parts List... 2 Soldering Guide (Part A)... 3 Soldering Guide (Part B)... 5 Soldering Guide Without Recommend Products... 8 Appendix...

More information

press light hot wet not press dark cold wet

press light hot wet not press dark cold wet Present sensor Light sensor Hot sensor Moisture sensor PTM switch LD Thermistor Matrix grid When the switch is press it closes the circuit and the output goes to. When the switch is not pressed the output

More information

A servo is an electric motor that takes in a pulse width modulated signal that controls direction and speed. A servo has three leads:

A servo is an electric motor that takes in a pulse width modulated signal that controls direction and speed. A servo has three leads: Project 4: Arduino Servos Part 1 Description: A servo is an electric motor that takes in a pulse width modulated signal that controls direction and speed. A servo has three leads: a. Red: Current b. Black:

More information

FCC Technician License Course

FCC Technician License Course FCC Technician License Course 2014-2018 FCC Element 2 Technician Class Question Pool Presented by: Tamiami Amateur Radio Club (TARC) WELCOME To the SECOND of 4, 3-hour classes presented by TARC to prepare

More information

Activity 2: Opto Receiver

Activity 2: Opto Receiver Activity 2: Opto Receiver Time Required: 45 minutes Materials List Group Size: 2 Each pair needs: One each of: One Activity 2 bag containing: o Two 10 μf Electrolytic Capacitors o 47 μf Electrolytic Capacitor

More information

16 Bit Micro Experimenter Assembly and Check out Instructions

16 Bit Micro Experimenter Assembly and Check out Instructions 16 Bit Micro Experimenter Assembly and Check out Instructions The kit you purchased that includes PCB, schematic, complete parts list and these assembly instructions. A top picture of the complete assembly

More information

Diode: 1n4007 DIODE IS USED BY LIDMOTOR

Diode: 1n4007 DIODE IS USED BY LIDMOTOR Diode: A diode is a two-terminal device, having two active electrodes, between which it allows the transfer of current in one direction only. Diodes are known for their unidirectional current property,

More information

LABORATORY EXPERIMENT. Infrared Transmitter/Receiver

LABORATORY EXPERIMENT. Infrared Transmitter/Receiver LABORATORY EXPERIMENT Infrared Transmitter/Receiver (Note to Teaching Assistant: The week before this experiment is performed, place students into groups of two and assign each group a specific frequency

More information