Ocean Controls KT-5221 Modbus IO Module

Size: px
Start display at page:

Download "Ocean Controls KT-5221 Modbus IO Module"

Transcription

1 Ocean Controls Modbus IO Module 8 Relay Outputs 4 Opto-Isolated Inputs 2 Analog Inputs (10 bit) 1 PWM Output (10 bit) 4 Input Counters Connections via Pluggable Screw Terminals 0-5V or 0-20mA Analog Inputs, Jumper Selectable 5A Relay Switching Power Indicator LED All enclosed in Professional looking plastic case Baud Modbus Slave Device Half Duplex 2-wire RS-485 The KT-5220 is a Modbus Slave IO module for interfacing to any PLC or PC using the Modbus protocol. It behaves as a Modbus Slave and Relays, Inputs and Outputs are controlled by writing to and reading from the Coils and Holding Registers. It can be used for many applications such as controlling lights and sprinkler systems, reading sensors and monitoring switches and other digital signals, or even for industrial control. The Relays are capable of switching up to 7A at 240VAC but the PCB tracks will only handle up to about 5A. Connections: Table 1 - Connections Label Description + Opto-Isolated Input Positive - Opto-Isolated Input Negative AN1 Analog Input 1 AN2 Analog Input 2 PWM PWM Output D+ RS-485 Data+ Connection D- RS-485 Data- Connection V+ 12V Power Supply Positive Input USB Unused NO Relay Normally Open Contact C Relay Common Contact NC Relay Normally Closed Contact Jumper Settings: The Analog inputs of the can be set for 0-5V or 0-20mA operation. Opening the case and inserting jumper shunts in the positions J1 and J2 will set the analog inputs to 0-20mA operation. Removing the shunts will set the analog inputs to 0-5V operation. Care must be taken to ensure that the inputs do not go above 5V or 20mA as damage to the microcontroller could occur. Using a jumper shunt in position J3 will enable a 120 Ohm termination resistor between the D+ and D- data lines. Using a jumper shunt to connect the SCL and COM pins of the I 2 C header pins will place the unit in default communications mode of Address 1, 9600 Baud, No Parity. 1 of 7

2 Using the Controller: The requires 12VDC to operate, this can come from a plug-pack, but you will need to remove any plug and connect the wires directly to the terminals. Connect the 12VDC positive to the V+ terminal and negative to the COM terminal next to it. Connect the to a PC using a RS-232 to RS485 or USB to RS-485 converter. Run the setup program to set the Modbus Address, Baud Rate and Parity. It can also be used to test the. Figure 1 - Test Program The main window of the software is shown in Figure 1. Enter the COM port number of the RS-485 port, which will be used to communicate with the unit in the COM text box. The address of the unit that is to be communicated with is entered in the address text box, the baud and parity can be selected from the menus. Clicking Use will open the specified COM port with the settings. Data transmitted to the unit is shown in the TX text box, data received from the unit is shown in the RX text box. If the settings of the unit need to be changed this can be done by adjusting the parameters and Relays can be turned on or off by checking or un-checking the check-boxes in the Relays group. Clicking the Check button in the Inputs group will make the program check the state of the s inputs. When an input is active the related box will change from red to green. The slider in the PWM group sets an output PWM percentage on the PWM output and the Check button in the Analogs group retrieves the value of the analog inputs and displays them on the bar graphs and in the text boxes. 2 of 7

3 Coils and Holding Registers: The Coils hold the status of the Digital Inputs and Relays. The Holding registers hold the counts for the Digital Inputs, the Analog Input readings and the PWM Output value. Tables 1 and 2 outline the Coils and Holding Registers. Table 1 - Coils Table 2 - Holding Registers Coil Use Value Register Use Value 1 Input 1 1=ON 0=OFF 1 Count Input 2 1=ON 0=OFF 2 Count Input 3 1=ON 0=OFF 3 Count Input 4 1=ON 0=OFF 4 Count Relay 1 1=ON 0=OFF 5 Analog In for 0-5V 6 Relay 2 1=ON 0=OFF 6 Analog In for 0-5V 7 Relay 3 1=ON 0=OFF 7 PWM output for 0-100% Duty 8 Relay 4 1=ON 0=OFF 9 Relay 5 1=ON 0=OFF 9990 Address Relay 6 1=ON 0=OFF 9991 Baudrate See Table 3 11 Relay 7 1=ON 0=OFF 9992 Parity See Table 4 12 Relay 8 1=ON 0=OFF Settings: The Address, Baud Rate and Parity are stored in the units EEPROM by writing to Holding Registers 9990 to Valid Slave Addresses are 1-243, the Baud Rate and Parity are set according to Tables 3 and 4. By default the unit will have Address = 1, Baud Rate = 9600 and Parity = None. New Address, Baud Rate and Parity parameters are loaded when the unit is powered up. If the unit does not respond, or an incorrect Address, Baud or Parity has been set the unit can be placed in default mode to enable a user to set correct parameters. This is done by inserting a jumper link between the SCL and COM pins of the I 2 C header pins inside the unit. With the jumper in this position parameters will be Address 1, 9600 Baud, No Parity. The unit can only operate with 8 data bits and 1 stop bit, However using Parity = Mark will behave the same way as no parity and 2 stop bits. Table 3 - Register Baud Rate Table 4 - Register Parity Value Baud Rate Value Parity Default / Default / 0 No Parity Odd Even Mark Space of 7

4 Circuit Page 1/3 - : Modbus IO Module 4 of 7

5 Circuit Page 2/3 - Inputs and Outputs: Modbus IO Module 5 of 7

6 Circuit Page 3/3 - Connecting to the : Connections 6 of 7

7 Parts List: 6-pin DIP socket U1-U4 4 8-pin DIP socket U pin DIP socket U pin DIP socket U8 1 4N35 Optocoupler U1-U4 4 ULN2803A Darlington Array U5 1 LTC485 Transceiver IC U7 1 PIC 18F2550 Microcontroller U Regulator VR1 1 1N4004 Diode D1-D Ohm Resistor R14, R Ohm Resistor R7, R Ohm Resistor R19 1 1k 1W Resistor R1-R4 4 4k7 Resistor R5, R6, R9-R13, R15, R17, R MHz Low Profile Crystal CR2 1 5mm LED in panel clip L1 1 22pF Capacitor C1, C uF Capacitor C3-C uF 25V Capacitor C10 1 Small Heatsink VR1 1 12V Relays RL1-RL8 8 Pluggable Terminal Socket 12 way X1-X14 3 Pluggable Terminal Socket 5 way X15-X16 1 Pluggable Terminal Socket 2 way X17 1 Pluggable Terminals 2 way X9-X15, X17 8 Pluggable Terminals 3 way X1-X8, X16 9 Case 1 M3 Screw 10mm 1 M3 Nut 1 Self Tapping Screws 4 PCB with Side Panels 1 Header pins (2pins) J1-J3 3 Header pins (3pins) I 2 C 1 Jumper Shunts J1-J3, SCL 4 2 Wire Ribbon 100mm 1 Not Used U6, CR1, BAT1, USB-B 7 of 7

Ocean Controls KT-5198 Dual Bidirectional DC Motor Speed Controller

Ocean Controls KT-5198 Dual Bidirectional DC Motor Speed Controller Ocean Controls KT-5198 Dual Bidirectional DC Motor Speed Controller Microcontroller Based Controls 2 DC Motors 0-5V Analog, 1-2mS pulse or Serial Inputs for Motor Speed 10KHz, 1.25KHz or 156Hz selectable

More information

DTMF decoder kit with 8 outputs and Morse transpond. 8 output DTMF decoder with 4 on board BT47 style 12V relays and 4 open collector outputs

DTMF decoder kit with 8 outputs and Morse transpond. 8 output DTMF decoder with 4 on board BT47 style 12V relays and 4 open collector outputs DJS Electronics Ltd cstech.co.uk DTMF decoder kit with 8 outputs and Morse transpond Features 8 output DTMF decoder with 4 on board BT47 style 12V relays and 4 open collector outputs Each output can be

More information

CMU232 User Manual Last Revised October 21, 2002

CMU232 User Manual Last Revised October 21, 2002 CMU232 User Manual Last Revised October 21, 2002 Overview CMU232 is a new low-cost, low-power serial smart switch for serial data communications. It is intended for use by hobbyists to control multiple

More information

NetBiter I/O Extender 4RO 6RTD 8DIO - DAIO User Manual Revision 1.00

NetBiter I/O Extender 4RO 6RTD 8DIO - DAIO User Manual Revision 1.00 NetBiter I/O Extender 4RO 6RTD 8DIO DAIO User Manual Revision 1.00 IntelliCom Innovation AB Linjegatan 3D SE302 50 Halmstad SWEDEN Phone +46 35 18 21 70 Fax +46 35 18 21 99 email info@intellicom.se www

More information

PROMUX Distributed MODBUS I/O Modules Catalog and Design Guide

PROMUX Distributed MODBUS I/O Modules Catalog and Design Guide PROMUX Distributed MODBUS I/O Modules Catalog and Design Guide 14/11/2006 V10 P.O.Box 24 Stanfield 3613 SOUTH AFRICA Tel: +27 (031) 7028033 Fax: +27 (031) 7028041 Email: proconel@proconel.com Web: www.proconel.com

More information

Data Acquisition Modules/ Distributed IO Modules

Data Acquisition Modules/ Distributed IO Modules User Manual Data Acquisition Modules/ Distributed IO Modules Future Design Controls, Inc. 7524 West 98 th Place / P.O. Box 1196 Bridgeview, IL 60455 888.751.5444 - Office: 888.307.8014 - Fax 866.342.5332

More information

PROMUX Distributed MODBUS I/O Modules Catalog and Design Guide

PROMUX Distributed MODBUS I/O Modules Catalog and Design Guide PROMUX Distributed MODBUS I/O Modules Catalog and Design Guide 12/03/2012 V11.0 P.O.Box 164 Seven Hills 1730 NSW AUSTRALIA Tel: +61 2 96248376 Fax: +61 2 9620 8709 Email: proconel@proconel.com Web: www.proconel.com

More information

VFSC9 ELECTRONIC SPEED CONTROLLER. Mounting and operating instructions

VFSC9 ELECTRONIC SPEED CONTROLLER. Mounting and operating instructions ELECTRONIC SPEED CONTROLLER Mounting and operating instructions Table of contents SAFETY AND PRECAUTIONS 3 PRODUCT DESCRIPTION 4 ARTICLE CODES 4 INTENDED AREA OF USE 4 TECHNICAL DATA 4 STANDARDS 5 WIRING

More information

Bill of Materials: PWM Stepper Motor Driver PART NO

Bill of Materials: PWM Stepper Motor Driver PART NO PWM Stepper Motor Driver PART NO. 2183816 Control a stepper motor using this circuit and a servo PWM signal from an R/C controller, arduino, or microcontroller. Onboard circuitry limits winding current,

More information

Single Channel Loop Detector

Single Channel Loop Detector Single Channel Loop Detector Model LD120T Series The LD120T is a series of single channel inductive loop detectors. The use of microprocessor and surface mount technology enables a large number of functions

More information

Applications. Operating Modes. Description. Part Number Description Package. Many to one. One to one Broadcast One to many

Applications. Operating Modes. Description. Part Number Description Package. Many to one. One to one Broadcast One to many RXQ2 - XXX GFSK MULTICHANNEL RADIO TRANSCEIVER Intelligent modem Transceiver Data Rates to 100 kbps Selectable Narrowband Channels Crystal controlled design Supply Voltage 3.3V Serial Data Interface with

More information

PS2-SMC-06 Servo Motor Controller Interface

PS2-SMC-06 Servo Motor Controller Interface PS2-SMC-06 Servo Motor Controller Interface PS2-SMC-06 Full Board Version PS2 (Playstation 2 Controller/ Dual Shock 2) Servo Motor Controller handles 6 servos. Connect 1 to 6 Servos to Servo Ports and

More information

MU110-16R(K) Digital output module 16 channel. User guide

MU110-16R(K) Digital output module 16 channel. User guide MU110-16R(K) Digital output module 16 channel User guide MU110-16R(K)_2016.12_0220_EN All rights reserved Subject to technical changes and misprints akytec GmbH Vahrenwalder Str. 269 A 30179 Hannover Germany

More information

MU110-8R(K) Digital output module 8 channel. User guide

MU110-8R(K) Digital output module 8 channel. User guide MU110-8R(K) Digital output module 8 channel User guide MU110-8R(K)_2019.01_0296_EN All rights reserved Subject to technical changes and misprints akytec GmbH Vahrenwalder Str. 269 A 30179 Hannover Germany

More information

Light sensor. 24V DC Power Input Common Ground Connection RS485 Data + Open Collector Output 2. Analogue Current Output Analogue Voltage Output

Light sensor. 24V DC Power Input Common Ground Connection RS485 Data + Open Collector Output 2. Analogue Current Output Analogue Voltage Output Light sensor PCB/enclosure temperature sensor Interface to PLCs using the MODBUS protocol Communicate via 2-wire S-485 Interface to instrumentation using to 2, 4 to 2, or to 1 V signals Generate alarms

More information

MD04-24Volt 20Amp H Bridge Motor Drive

MD04-24Volt 20Amp H Bridge Motor Drive MD04-24Volt 20Amp H Bridge Motor Drive Overview The MD04 is a medium power motor driver, designed to supply power beyond that of any of the low power single chip H-Bridges that exist. Main features are

More information

Relay 3 Click. PID: MIKROE 3357 Weight: 42 g

Relay 3 Click. PID: MIKROE 3357 Weight: 42 g Relay 3 Click PID: MIKROE 3357 Weight: 42 g Relay click 3 is a dual relay Click board, featuring two single-pole doublethrow relays which can be operated by output pins of the host microcontroller (MCU).

More information

SMARTALPHA RF TRANSCEIVER

SMARTALPHA RF TRANSCEIVER SMARTALPHA RF TRANSCEIVER Intelligent RF Modem Module RF Data Rates to 19200bps Up to 300 metres Range Programmable to 433, 868, or 915MHz Selectable Narrowband RF Channels Crystal Controlled RF Design

More information

Harris IRT Enterprises Multi-Channel Digital Resistance Tester Model XR

Harris IRT Enterprises Multi-Channel Digital Resistance Tester Model XR Harris IRT Enterprises Multi-Channel Digital Resistance Tester Model 6012-06XR Specifications & Dimensions 2 Theory of Operation 3 System Block Diagram 4 Operator Controls & Connectors 5 Test Connections

More information

Ten Tec DDS Board Assembly Procedure

Ten Tec DDS Board Assembly Procedure 05 May 2014 Ten Tec DDS Board Assembly Procedure You will find a photo of a completed board at the end of these instructions. Refer it whenever clarification is required. 1. AD9835 Attachment If you purchased

More information

AcuMesh Wireless RS485 Network. User's Manual SOLUTION

AcuMesh Wireless RS485 Network. User's Manual SOLUTION AcuMesh Wireless RS485 Network User's Manual AN SOLUTION ACUMESH - WIRELESS METERING SYSTEM COPYRIGHT 2015 V1.2 This manual may not be altered or reproduced in whole or in part by any means without the

More information

WTPCT-M. eeder. Pulse Counter/Timer Module. Technologies FEATURES SPECIFICATIONS DESCRIPTION. Weeder Technologies

WTPCT-M. eeder. Pulse Counter/Timer Module. Technologies FEATURES SPECIFICATIONS DESCRIPTION. Weeder Technologies eeder Technologies 90-A Beal Pkwy NW, Fort Walton Beach, FL 32548 www.weedtech.com 850-863-5723 Pulse Counter/Timer Module FEATURES Reads frequency from 0.50000 to 1,400,000 Hz using 5 digit resolution

More information

DigiSpeed DC-03. Isolated Control Voltage Generator User s Guide. PCB: DC-03 V3.0 Firmware: Ver: 3.0 Mach3: Ver: 1.84

DigiSpeed DC-03. Isolated Control Voltage Generator User s Guide. PCB: DC-03 V3.0 Firmware: Ver: 3.0 Mach3: Ver: 1.84 DigiSpeed DC-03 - Users Guide Page 1 Updated: 29. April 2009 DigiSpeed DC-03 Isolated Control Voltage Generator User s Guide PCB: DC-03 V3.0 Firmware: Ver: 3.0 Mach3: Ver: 1.84 DigiSpeed DC-03 - Users

More information

BandMaster V Manual. Installation

BandMaster V Manual. Installation BandMaster V Manual Installation Installing and configuring the BM-5 BandMaster V is a simple process. All the configuration process is done from the front panel. Installation and configuration steps are

More information

B850 Boiler House Energy Monitor

B850 Boiler House Energy Monitor Local regulations may restrict the use of this product to below the conditions quoted. In the interests of development and improvement of the product, we reserve the right to change the specification without

More information

DIY KIT 141. Multi-Mode Timer

DIY KIT 141. Multi-Mode Timer INTRODUCTION No one can call themselves an electronics hobbyist unless they have built a timer. There are many tens of designs using a variety of new and sometimes old circuits. Witness the longest surviving

More information

Guardian and DL3282 Modem Interface Technical Service Application Note

Guardian and DL3282 Modem Interface Technical Service Application Note Guardian and DL3282 Modem Interface Technical Service Application Note OVERVIEW The following document is designed to provide information for the implementation of the Guardian Wireless Modem/Analog Radio

More information

QRPGuys SMT Digital Dial/Frequency Counter

QRPGuys SMT Digital Dial/Frequency Counter QRPGuys SMT Digital Dial/Frequency Counter First, familiarize yourself with the parts and check for all the components. If a part is missing, please contact us and we will send one. You must use qrpguys.parts@gmail.com

More information

SMR5000F. User Manual. Smart Radio Data Repeater. Web Site: P.N.: Book 092

SMR5000F. User Manual. Smart Radio Data Repeater. Web Site:  P.N.: Book 092 SMR5000F Smart Radio Data Repeater User Manual ISRAEL Office: Email: info@kpsystems.com PO Box 42, Tefen Industrial Park, Tefen 24959 Tel: 972-4-987-3066 / Fax: 972-4-987-3692 USA Office: KP ELECTRONICS,

More information

Assembly Manual for VFO Board 2 August 2018

Assembly Manual for VFO Board 2 August 2018 Assembly Manual for VFO Board 2 August 2018 Parts list (Preliminary) Arduino 1 Arduino Pre-programmed 1 Faceplate Assorted Header Pins Full Board Rev A 10 104 capacitors 1 Rotary encode with switch 1 5-volt

More information

Servo click. PID: MIKROE 3133 Weight: 32 g

Servo click. PID: MIKROE 3133 Weight: 32 g Servo click PID: MIKROE 3133 Weight: 32 g Servo click is a 16-channel PWM servo driver with the voltage sensing circuitry. It can be used to simultaneously control 16 servo motors, each with its own programmable

More information

LED Field Strength Indicator Kit

LED Field Strength Indicator Kit LED Field Strength Indicator Kit Description The Field Strength Indicator kit from Qrpkits.com provides a visual way to monitor RF fields through the brightness of an LED. It will respond to RF fields

More information

SRC-110 Series Zone Controllers with Modbus RTU

SRC-110 Series Zone Controllers with Modbus RTU Product sheet CT2.142 Type SRC-110-MOD SRC-110 Series Zone Controllers with Modbus RTU The SRC-110 series controllers have been designed for zone heating and cooling control. The controllers have 3 analogue

More information

EVDP610 IXDP610 Digital PWM Controller IC Evaluation Board

EVDP610 IXDP610 Digital PWM Controller IC Evaluation Board IXDP610 Digital PWM Controller IC Evaluation Board General Description The IXDP610 Digital Pulse Width Modulator (DPWM) is a programmable CMOS LSI device, which accepts digital pulse width data from a

More information

The MP SERIES CONTROLLER. User s Manual. ISE, Inc.

The MP SERIES CONTROLLER. User s Manual. ISE, Inc. The MP SERIES CONTROLLER User s Manual ISE, Inc. 10100 Royalton Rd. Cleveland, OH 44133 USA Tel: (440) 237-3200 Fax: (440) 237-1744 http://variac.com Form No, 003-1622 Rev G 02/25/2009 Form No. 003-1622

More information

269 Troubleshooting Guide 11/4/98 1

269 Troubleshooting Guide 11/4/98 1 269 Troubleshooting Guide 11/4/98 1 Table of Contents Phase currents 3 Communications. 6 RTDs.. 9 Ground Fault Currents... 13 Output Relays. 15 Analog Output 17 Switch Inputs...18 11/4/98 2 Phase Currents

More information

Pacific Antenna Easy TR Switch

Pacific Antenna Easy TR Switch Pacific Antenna Easy TR Switch Kit Description The Easy TR Switch is an RF sensing circuit with a double pole double throw relay that can be used to automatically switch an antenna between a separate receiver

More information

List of Items Available in the Laboratory the Lab

List of Items Available in the Laboratory the Lab List of Items Available in the Laboratory the Lab Category Component 555 Timer $0.30 5V Relay $3.50 74xxx Series IC Chip $0.30 Battery - 12V (rechargeable Lead-acid type) $16.00 Battery - 6V (rechargeable

More information

Dual Band Filter Assembly Manual

Dual Band Filter Assembly Manual Dual Band Filter Assembly Manual 12 January 2018 Rev D Version Theory of Operation: The purpose of a Bandpass Filter is to filter out or reject all unwanted signals. The original KN-Q7A Receive Filter

More information

WTDIN-M. eeder. Digital Input Module. Technologies FEATURES SPECIFICATIONS DESCRIPTION. Weeder Technologies

WTDIN-M. eeder. Digital Input Module. Technologies FEATURES SPECIFICATIONS DESCRIPTION. Weeder Technologies eeder Technologies 90-A Beal Pkwy NW, Fort Walton Beach, FL 32548 www.weedtech.com 850-863-5723 Digital Input Module FEATURES 8 wide-range digital input channels with high voltage transient protection.

More information

20-27B. Tone Panel. Version 1.10

20-27B. Tone Panel. Version 1.10 20-27B Tone Panel Version 1.10 Printings Version 1.00: 1/16/01 Version 1.10: 10/11/02 TABLE OF CONTENTS SPECIFICATIONS... 1 1.0 GENERAL DESCRIPTION... 2 1.1 Description... 2 1.2 Capabilities and Features...

More information

WTDOT-M. eeder. Digital Output Module. Technologies FEATURES SPECIFICATIONS DESCRIPTION. Weeder Technologies

WTDOT-M. eeder. Digital Output Module. Technologies FEATURES SPECIFICATIONS DESCRIPTION. Weeder Technologies eeder Technologies 90-A Beal Pkwy NW, Fort Walton Beach, FL 32548 www.weedtech.com 850-863-5723 Digital Output Module FEATURES 8 high-current open-collector output channels with automatic overload shutdown.

More information

C S Technology Ltd. cstech.co.uk. DTMF decoder kit with relay output, opto coupled input & Morse transpond.

C S Technology Ltd. cstech.co.uk. DTMF decoder kit with relay output, opto coupled input & Morse transpond. C S Technology Ltd cstech.co.uk DTMF decoder kit with relay output, opto coupled input & Morse transpond. Our DTMF Opto decoder kit has one relay output offering clean contacts, and one Opto coupled input

More information

DDS VFO 2 CONSTRUCTION MANUAL. DDS VFO 2 Construction Manual Issue 1 Page 1

DDS VFO 2 CONSTRUCTION MANUAL. DDS VFO 2 Construction Manual Issue 1 Page 1 DDS VFO 2 CONSTRUCTION MANUAL DDS VFO 2 Construction Manual Issue 1 Page 1 Important Please read before starting assembly STATIC PRECAUTION The DDS VFO kit contains the following components which can be

More information

PROCESS & TEMPERATURE CONTROLLERS

PROCESS & TEMPERATURE CONTROLLERS PROCESS & TEMPERATURE CONTROLLERS NOVA PD54 Series Thermocouple, RTD, & Process Inputs High Accuracy Auto-Tuning PID Heating & Cooling Models Universal Power Supply 1-24 VAC Up to 3 Relays & 2 Analog Outputs

More information

Netbiter IO Extender 4RO 6RTD 8DIO DAIO 8AIV 8AIIS

Netbiter IO Extender 4RO 6RTD 8DIO DAIO 8AIV 8AIIS USER MANUAL Netbiter IO Extender 4RO 6RTD 8DIO DAIO 8AIV 8AIIS Doc ID: HMSI-27-228 Version: 2.0 HALMSTAD CHICAGO KARLSRUHE TOKYO BEIJING MILANO MULHOUSE COVENTRY PUNE COPENHAGEN RAVENSBURG HMS Industrial

More information

MV110-8AS. Analog input module 8 channel. User guide

MV110-8AS. Analog input module 8 channel. User guide MV110-8AS Analog input module 8 channel User guide MV110-8AS_2016.12_0226_EN All rights reserved Subject to technical changes and misprints Contents 1 Description... 2 1.1 Function... 2 1.2 RS485 network...

More information

Modbus communication module for TCX2: AEX-MOD

Modbus communication module for TCX2: AEX-MOD Modbus communication module for TCX2: Communication Specification TCX2 is factory installed in TCX2 series controllers with -MOD suffix, and is also available separately upon request for customer installation

More information

The first RADIO Communication Module designed for the weighing industry

The first RADIO Communication Module designed for the weighing industry The first RADIO Communication Module designed for the weighing industry SCALELINK - AURORA WIRELESS LINK Step 1: Get Connected A) Disconnect the indicator (or other device) from power. Connect the ScaleLink

More information

Brushless DC Motor Controller Specification Assemblies 025F0248

Brushless DC Motor Controller Specification Assemblies 025F0248 Brushless DC Motor Controller Specification Assemblies 025F0248 600A1099 Rev. B April 4 th, 2014 Revision History EC Date Description Rev EC54318 09/03/13 Initial Release A EC58093 04/04/14 Added cap discharge

More information

isys-4004 GUI interface - V2.1 Power up Initialize Peripheral Start Measurement YES LED flashes red Object available LED blinking

isys-4004 GUI interface - V2.1 Power up Initialize Peripheral Start Measurement YES LED flashes red Object available LED blinking isys-4004 GUI interface - V2.1 Power up Initialize Peripheral Start Measurement Mode Object available YES LED flashes red NO LED blinking isys-4004 distance sensor GUI description content 1. connecting

More information

Pacific Antenna - Easy TR Switch

Pacific Antenna - Easy TR Switch Pacific Antenna - Easy TR Switch Kit Description The Easy TR Switch is an RF sensing switch that can be used to switch an antenna between a receiver and transmitter. It also has a second switched pair

More information

Pacific Antenna Field Strength Indicator Kit

Pacific Antenna Field Strength Indicator Kit Pacific Antenna Field Strength Indicator Kit Description The Field Strength Indicator kit from Pacific Antenna provides a visual way to monitor the presence and relative strength RF fields through the

More information

Simple Servo USER Instructions

Simple Servo USER Instructions Simple Servo USER Instructions Version 1V2 Copyright 2003-2007 Active Robots Limited 10A New Rock Ind. Est., Newrock, Chilcompton, Somerset BA3 4JE UK Tel: +44(0)1761 239 267 Fax: +44(0)176 123 3162 www.active-robots.com

More information

User Manual Netbiter IO Extender 4RO 6RTD 8DIO DAIO 8AIx 8AIIx

User Manual Netbiter IO Extender 4RO 6RTD 8DIO DAIO 8AIx 8AIIx User Manual Netbiter IO Extender 4RO 6RTD 8DIO DAIO 8AIx 8AIIx Doc. ID. HMSI27228 Rev. 1.20 Connecting Devices TM HALMSTAD CHICAGO KARLSRUHE TOKYO BEIJING MILANO MULHOUSE COVENTRY PUNE COPENHAGEN HMS Industrial

More information

User Manual EnOcean V 0.1

User Manual EnOcean V 0.1 & User Manual EnOcean V 0.1 Last update: July 2012 All software-related descriptions refer to the software V1279. We recommend to update older versions of the system. Small deviations in the description

More information

MK110-8D.4R. Digital I/O-Module 12 channel 8 DI, 4 DO. User guide

MK110-8D.4R. Digital I/O-Module 12 channel 8 DI, 4 DO. User guide MK110-8D.4R Digital I/O-Module 12 channel 8 DI, 4 DO User guide MK110-8D4R_2016.12_0219_EN All rights reserved Subject to technical changes and misprints akytec GmbH Vahrenwalder Str. 269 A 30179 Hannover

More information

ALX-SSB 5 Band Filter Assembly Manual 19 November 2018

ALX-SSB 5 Band Filter Assembly Manual 19 November 2018 ALX-SSB 5 Band Filter Assembly Manual 19 November 2018 Contents Theory of Operation:... 1 Figure 1... 2 Parts Included:... 4 Board Overview:... 5 Figure 2... 5 Figure 3... 5 Board Assembly:... 6 Cable

More information

4ms SCM Breakout. Kit Builder's Guide for PCB v2.1 4mspedals.com

4ms SCM Breakout. Kit Builder's Guide for PCB v2.1 4mspedals.com 4ms SCM Breakout Kit Builder's Guide for PCB v2.1 4mspedals.com Shuffling Clock Multiplier Breakout This guide is for building a Shuffling Clock Multiplier Breakout module (SCMBO) version 2.1 from the

More information

B850 Boiler House Energy Monitor

B850 Boiler House Energy Monitor Local regulations may restrict the use of this product to below the conditions quoted. In the interests of development and improvement of the product, we reserve the right to change the specification without

More information

DASL 120 Introduction to Microcontrollers

DASL 120 Introduction to Microcontrollers DASL 120 Introduction to Microcontrollers Lecture 2 Introduction to 8-bit Microcontrollers Introduction to 8-bit Microcontrollers Introduction to 8-bit Microcontrollers Introduction to Atmel Atmega328

More information

BV4112. Serial Micro stepping Motor Controller. Product specification. Dec V0.a. ByVac Page 1 of 18

BV4112. Serial Micro stepping Motor Controller. Product specification. Dec V0.a. ByVac Page 1 of 18 Product specification Dec. 2012 V0.a ByVac Page 1 of 18 SV3 Relay Controller BV4111 Contents 1. Introduction...4 2. Features...4 3. Electrical interface...4 3.1. Serial interface...4 3.2. Motor Connector...4

More information

User Manual. Data Acquisition Modules/ Distributed IO Modules

User Manual. Data Acquisition Modules/ Distributed IO Modules User Manual Data Acquisition Modules/ Distributed IO Modules UMIOE Rev 5.0, 10/2009 COPYRIGHT NOTICE This manual is a publication of Brainchild Electronics Co.. Ltd. and is provided for use by its customers

More information

MODBUS MULTIPLEXING I/O SYSTEM CATALOG AND DESIGN GUIDE

MODBUS MULTIPLEXING I/O SYSTEM CATALOG AND DESIGN GUIDE MODMUX MODBUS MULTIPLEXING I/O SYSTEM CATALOG AND DESIGN GUIDE 22/02/2008 V19 P.O.Box 24 Stanfield 3613 SOUTH AFRICA Tel: 27 (031) 7028033 Fax: 27 (031) 7028041 Email: proconel@proconel.com Web: www.proconel.com

More information

Controlling DC Brush Motor using MD10B or MD30B. Version 1.2. Aug Cytron Technologies Sdn. Bhd.

Controlling DC Brush Motor using MD10B or MD30B. Version 1.2. Aug Cytron Technologies Sdn. Bhd. PR10 Controlling DC Brush Motor using MD10B or MD30B Version 1.2 Aug 2008 Cytron Technologies Sdn. Bhd. Information contained in this publication regarding device applications and the like is intended

More information

MultiNet. Instruction Manual. Digital Energy Multilin. Serial to Ethernet Converter. Manual P/N: A2 Copyright 2009 GE Multilin

MultiNet. Instruction Manual. Digital Energy Multilin. Serial to Ethernet Converter. Manual P/N: A2 Copyright 2009 GE Multilin Digital Energy Multilin MultiNet Serial to Ethernet Converter Instruction Manual Manual P/N: 1601-0117-A2 Copyright 2009 GE Multilin NORTH AMERICA / WORLDWIDE 215 Anderson Avenue, Markham, ON Canada L6E

More information

DEC-001 Installation Instructions

DEC-001 Installation Instructions DEC-001 Installation Instructions Skill Level: The installation of this assembly requires a medium level of expertise in working with modern electronic equipment. The use of appropriate tools, correct

More information

Beta-test ED1 PCB installed in I0CG s K1

Beta-test ED1 PCB installed in I0CG s K1 K1 SSB Modification (Ed.2) This description provides the receiver (RX) modifications, assembly, alignment and operation as a first step. In a second step you can add the remaining transmitter (TX) modifications,

More information

Galil Motion Control. DMC 3x01x. Datasheet

Galil Motion Control. DMC 3x01x. Datasheet Galil Motion Control DMC 3x01x Datasheet 1-916-626-0101 Galil Motion Control 270 Technology Way, Rocklin, CA [Type here] [Type here] (US ONLY) 1-800-377-6329 [Type here] Product Description The DMC-3x01x

More information

PLC-K506 Series FEATURES DESCRIPTION FEATURES

PLC-K506 Series FEATURES DESCRIPTION FEATURES FEATURES Two High Speed Counters Two Pulse Train Outputs Two Pulse Width Modulation Outputs Inputs 10 Outputs 1 RS232 Port 2 RS485 Ports Supports Modbus RTU Protocol Communicate With Up to 32 Devices DESCRIPTION

More information

3.3V regulator. JA H-bridge. Doc: page 1 of 7

3.3V regulator. JA H-bridge. Doc: page 1 of 7 Cerebot Reference Manual Revision: February 9, 2009 Note: This document applies to REV B-E of the board. www.digilentinc.com 215 E Main Suite D Pullman, WA 99163 (509) 334 6306 Voice and Fax Overview The

More information

Harris IRT Enterprises, Inc. Digital Resistance Tester Model A

Harris IRT Enterprises, Inc. Digital Resistance Tester Model A Harris IRT Enterprises, Inc. Equipment Configuration 2 Specifications & Dimensions 3 Theory of Operation 4 Operation of Unit 5 Calibration Procedure 7 Options 9 RS-232 Configuration 11 BCD Configuration

More information

PCAN-MicroMod Evaluation Test and Development Environment for the PCAN-MicroMod. User Manual. Document version ( )

PCAN-MicroMod Evaluation Test and Development Environment for the PCAN-MicroMod. User Manual. Document version ( ) PCAN-MicroMod Evaluation Test and Development Environment for the PCAN-MicroMod User Manual Document version.0. (0-0-) Relevant products Product Name Part number Model PCAN-MicroMod Evaluation Board IPEH-000

More information

ABC V1.0 ASSEMBLY IMPORTANT!

ABC V1.0 ASSEMBLY IMPORTANT! ABC V1.0 ASSEMBLY Before starting this kit, prepare the following tools: Soldering iron (15-20W will do), flush cutters, no.2 hex screwdriver or allen key and phillips screwdriver. Also briefly go through

More information

DigiSpeed-GX DC-03. Isolated Control Voltage Generator User s Guide. DigiSpeed-GX PCB Ver:2.0 Firmware Ver: 1.0 Mach3 Ver: 1.84

DigiSpeed-GX DC-03. Isolated Control Voltage Generator User s Guide. DigiSpeed-GX PCB Ver:2.0 Firmware Ver: 1.0 Mach3 Ver: 1.84 DigiSpeed-GX - Users Guide Page 1 Updated: 15. January 2009 DigiSpeed-GX DC-03 Isolated Control Voltage Generator User s Guide DigiSpeed-GX PCB Ver:2.0 Firmware Ver: 1.0 Mach3 Ver: 1.84 DigiSpeed-GX -

More information

BassAce - Midi Bass Synthesizer. BassAce Features

BassAce - Midi Bass Synthesizer. BassAce Features Untitled Document BassAce - Midi Bass Synthesizer The BassAce is a small midi-synth based loosely on the TB303. It can be built many different ways. Depending on how it's configured it can be anything

More information

Lecture #3 RS232 & 485 protocols

Lecture #3 RS232 & 485 protocols SPRING 2015 Integrated Technical Education Cluster At AlAmeeria E-626-A Data Communication and Industrial Networks (DC-IN) Lecture #3 RS232 & 485 protocols Instructor: Dr. Ahmad El-Banna 1 Agenda What

More information

DEM Part Number L144-28INTCK 144 MHz Transverter Kit and complete kit

DEM Part Number L144-28INTCK 144 MHz Transverter Kit and complete kit DEM Part Number L144-28INTCK 144 MHz Transverter Kit and complete kit Power Out: Noise Figure and Gain: DC Power Requirement: 50 mw linear minimum 3.5 db NF nominal, 5 dbg maximum 12-15.5 VDC, 13.8 nominal

More information

Circuit Board Assembly Instructions

Circuit Board Assembly Instructions Circuit Board Assembly Instructions This document walk you through the assembly of the Base4 Clock v1.2 - v1.3 circuit boards. Important note for kit buyers The color and appearance of the components may

More information

MultiNet Serial to Ethernet Converter

MultiNet Serial to Ethernet Converter GE Grid Solutions MultiNet Serial to Ethernet Converter Instruction Manual Firmware Revision 1.x Manual P/N: 1601-0117-A4 GE Publication Number: GEK-106498C *1601-0220-A4* Copyright 2017 GE Multilin Inc.

More information

Shenzhen ATC Technology CO.,LTD ATC. A-1 Serial Remote I/O Module. User Manual. V1.13 Edit:2018/01/

Shenzhen ATC Technology CO.,LTD ATC. A-1 Serial Remote I/O Module. User Manual. V1.13 Edit:2018/01/ ATC A-1 Serial Remote I/O Module User Manual V1.13 Edit:2018/01/30-1 - Catalogue 1.The introduction of Modbus protocol...- 3-1.1 Modbus protocol master-slave response process... - 3-1.2 Modbus register

More information

A Super trainer with advanced hardware and software features only found in very expensive equipment.

A Super trainer with advanced hardware and software features only found in very expensive equipment. PLC Trainer PTS T100 LAB EXPERIMENTS A Super trainer with advanced hardware and software features only found in very expensive equipment. You won t find any similar equipment among our competitors at such

More information

Analog Module D1-15P User Manual

Analog Module D1-15P User Manual D1-15P Manual Analog Module D1-15P User Manual Sielco Elettronica Srl Edison Street 209 20019 Settimo Milanese (MI) - Italy http://www.sielcoelettronica.com info @ sielcoelettronica.com Tel 02 48916252

More information

OptiLogic Series. Input/Output Modules. Optimal Automation for Industry. Optimation, Inc. (256)

OptiLogic Series. Input/Output Modules. Optimal Automation for Industry. Optimation, Inc. (256) Input/Output Modules Optimal Automation for Industry Optimation, Inc. ()-00 WARNING Thank you for purchasing industrial control products from Optimation, Inc. We want your new system to operate safely.

More information

GF of 9 THE GADGET FREAK FILES CASE #165. Analog Clock Measures Time in Meters

GF of 9 THE GADGET FREAK FILES CASE #165. Analog Clock Measures Time in Meters GF 165 04-05-2010 1 of 9 THE GADGET FREAK FILES CASE #165 Analog Clock Measures Time in Meters Alan Parekh took a different approach to time keeping with his electronic clock that registers hours, minutes,

More information

6. HARDWARE PROTOTYPE AND EXPERIMENTAL RESULTS

6. HARDWARE PROTOTYPE AND EXPERIMENTAL RESULTS 6. HARDWARE PROTOTYPE AND EXPERIMENTAL RESULTS Laboratory based hardware prototype is developed for the z-source inverter based conversion set up in line with control system designed, simulated and discussed

More information

G11+ GSDR quick start assembly manual [Part 2]

G11+ GSDR quick start assembly manual [Part 2] G11+ GSDR quick start assembly manual [Part 2] January 31, 2012 Ver 1.1 Tasa, YU1LM and Nick, VK2DX Overview G11 quick start assembly manual Part 2 covers assembly of the TX components. There are two chapters

More information

MULTI-DROPS DIGITAL MODEM FOR PRIVATE LINE

MULTI-DROPS DIGITAL MODEM FOR PRIVATE LINE Distribué par : Contact : hvssystem@hvssystem.com Tél : 0326824929 Fax : 0326851908 Siège social : 2 rue René Laennec 51500 Taissy France www.hvssystem.com MDM192 MULTI-DROPS DIGITAL MODEM FOR PRIVATE

More information

SSRP LTC1746 Assembly Manual V0.1 Check the most recent version

SSRP LTC1746 Assembly Manual V0.1 Check the most recent version SSRP LTC1746 Assembly Manual V0.1 Check the most recent version http://oscar.dcarr.org/ssrp/hardware/ltc1746/ltc1746.php Introduction This manual details the general assembly process for the SSRP LTC1746

More information

g GE POWER MANAGEMENT

g GE POWER MANAGEMENT 469 FREQUENTLY ASKED QUESTIONS 1 Can not communicate through the front port RS232 Check the following settings Communication port on your computer ( com1, com2 com3 etc ) Parity settings must match between

More information

KNC-PLC-K506 Series FEATURES DESCRIPTION FEATURES

KNC-PLC-K506 Series FEATURES DESCRIPTION FEATURES FEATURES Two High Speed Counters Two Pulse Train Outputs Two Pulse Width Modulation Outputs Inputs 10 Outputs 1 RS232 Port 2 RS485 Ports Supports Modbus RTU Protocol Communicate with up to 32 devices DESCRIPTION

More information

Tarocco Closed Loop Motor Controller

Tarocco Closed Loop Motor Controller Contents Safety Information... 3 Overview... 4 Features... 4 SoC for Closed Loop Control... 4 Gate Driver... 5 MOSFETs in H Bridge Configuration... 5 Device Characteristics... 6 Installation... 7 Motor

More information

Characteristics and functioning

Characteristics and functioning Characteristics and functioning /25 ENOD4 PRODUCT RANGE:... 4. General presentation:... 4.2 enodview software tool... 4.3 Versions and options:... 4.3. Versions:...4.3.2 Options :...4.4 Dimensions:...

More information

Custom Integrated Circuit (MSM9520RS) Replacement Module

Custom Integrated Circuit (MSM9520RS) Replacement Module FT-101Z/ FT-107/ FT-707/ FT-901,902 (later version) DISPLAY COUNTER UNIT (PB-2086A) Custom Integrated Circuit (MSM9520RS) Replacement Module Assembly and Installation Manual (v1.3e) STEP-BY-STEP PROCEDURES

More information

Specifications.

Specifications. is a 7 capacitive touch display designed for use with PanelPilotACE Design Studio, a free drag-and-drop style software package for rapid development of advanced user interfaces and panel meters. The is

More information

Training Schedule. Robotic System Design using Arduino Platform

Training Schedule. Robotic System Design using Arduino Platform Training Schedule Robotic System Design using Arduino Platform Session - 1 Embedded System Design Basics : Scope : To introduce Embedded Systems hardware design fundamentals to students. Processor Selection

More information

HURRICANE Radio Modem. FULL DUPLEX Radio MODEM

HURRICANE Radio Modem. FULL DUPLEX Radio MODEM FULL DUPLEX Radio MODEM Direct Cable Replacement Range 2KM RS232 / RS485 / USB Host Data Rates up to 38,400 Baud RF Data Rates to 115200Kbps Waterproof IP68 Enclosure 8 User Selectable Channels CE Compliant

More information

RGB Driver click. PID: MIKROE 3078 Weight: 28 g

RGB Driver click. PID: MIKROE 3078 Weight: 28 g RGB Driver click PID: MIKROE 3078 Weight: 28 g RGB Driver click is an RGB LED driver, capable of driving RGB LED stripes, LED fixtures and other RGB LED applications that demand an increased amount of

More information

by illumicon Morse ID generator Pietershoek XA Veldhoven The Netherlands fax

by illumicon Morse ID generator Pietershoek XA Veldhoven The Netherlands fax by illumicon www.ezkits.eu Morse ID generator Pietershoek 3 5503XA Veldhoven The Netherlands fax +31-40-2230020 Contents Introduction...3 Soldering Tips...3 Assembly...4 Schematic...5 Connections...6 Configuration...7

More information

CONTROL MICROSYSTEMS SCADAWave Radio Transceiver. Hardware Manual

CONTROL MICROSYSTEMS SCADAWave Radio Transceiver. Hardware Manual 5908 SCADAWave Radio Transceiver Hardware Manual CONTROL MICROSYSTEMS SCADA products... for the distance 48 Steacie Drive Telephone: 613-591-1943 Kanata, Ontario Facsimile: 613-591-1022 K2K 2A9 Technical

More information