Vol SCAVOL14E1502H1

Transcription

1 Vol.14

2 For CorreCt Use of super CapaCitors 1. Please confirm the operating conditions and the specifications of the Super Capacitors befor using them. 2. The electrolyte of these Super Capacitors is sealed with material such as rubber. When you use the capacitors for a long time at high temperature, the moisture of the eleotrolyte evaporates and the equivalent series resistance (E.S.R.) increases. The fundamental failure mode is the open mode depending on E.S.R. increase. When using a capacitor, please introduce a safe design assuming unexpected capacitor failure, such as redundancy in design and protection from fire and erroneous operation. 3. Please read Notes on Using the Super Capacitor on page 60 when you design the circuits using the Super Capacitors.

3 CONTENTS page 1. Organization of Super Capacitor Series 4 2. Performance for Selection 5 3. Characteristics of Super Capacitor 5 4. Typical Applications 6 5. Part Number System 7 6. Rated Specifications FC Series SMD Type FM Series FG Series FT Series FY Series FR Series FS Series FA FE Series HV Series High Type Packing Measurement Conditions Notes on Using Super Capacitor Electric Double-Layer Capacitor 38

4 1. Organization of Super Capacitor Series -25 to 70 guaranteed -40 to 85 guaranteed ma order back-up μa order back-up For automatic mounting (SMD) (embossad taping) FC series 3.5 to 5.5V For automatic mounting (radial taping) FME Type 5.5V FM series 3.5 to 6.5V FMR Type 3.5 to 5.5V -40 to 85 guaranteed Can Case type (self-supporting Type) FT series 5.5V FG series 3.5 to 5.5V FGR Type 5.5V FS series 5.5 to 11V FY series 3.5 to 5.5V FR series 5.5V FE series 5.5V FA series 5.5 to 11V For A order current HV series 2.5 to 2.7V 1 to 200F 4 Super Capacitors Vol.14

5 2. Performance for Selection Backup current depends on SuperCapacitor equivalent series resistance () Low High ka A ma μa Backup current High power SuperCapacitor HV Series Low impedance application use FA, FE, FS, FT, FM Series High impedance application use FG, FY, FC, FM, FR Series Backup time 1 minute 1 hour 1 day 1 week 1 month ( sec ) Backup time depends on capacitance 3. Characteristics of Super Capacitor Super Capacitor can not be used for applications in AC circuit such as ripple absorption because it has high internal resistance (several hundred m to a hundred ) compared to aluminum electrolysis capacitor. Thus its main use would be similar to that of secondary battery such as power back-up in DC circuit. The following list shows the characteristics of Super Capacitors as compared to aluminum electrolyses capacitors for power back-up and secondary batteries. Secondary battery Capacitor NiCd battery Lithium ion battery Aluminum electrolysis capacito Super Capacitor Back-up ability Eco-hazard Cd Operating temperature range 20 to to to to 85 FR FT Charge time few hours few hours few minutes few minutes Charge/discharge life time approx. 500 times approx. 500 to 1000 times limitless (*1) limitless (*1) Restrictions on charge/discharge yes yes none none Flow soldering not applicable not applicable applicable applicable Automatic mounting not applicable not applicable applicable applicable (FM and FC series) Safety risks leakage, explosion leakage, combustion, explosion, ignition heat-up, explosion gas emission (*2) (*1) Aluminum electrolysis capacitor and Super Capacitor has limited lifetime. However, when used under proper conditions, both can operate sufficiently within the designed lifetime of the set they are built in. (*2) There is no harm as it is a mere leak of water vapor which transitioned from water contained in the electrolyte However, application of abnormal voltage surge exceeding maximum operating voltage may result in leakage and explosion. Except HV series. Super Capacitors Vol.14 5

6 4. Typical Applications As in the characteristics remarked previously, Super Capacitor has characteristics intermediate between general capacitors and batteries. Because of this, Super Capacitor can be used like a secondary battery when applied to DC circuit. The best suited applications of Super Capacitor are back-up device for the power shut-down of micro computers and RAM's. The list below shows main application examples. Application Examples of Super Capacitor Intended use (guideline) Power supply (guideline) Application Examples of equipments Series Long time back-up 500 A and below CMOS RAM, IC for clocks CMOS micro computer, IC for clocks Measuring device, Control equipment, Communication device, Automotive power source CMOS micro computer Static RAM/DTS (digital tuning system) FR series (85 guaranteed) FC series FG series FY series FM series Micro computer, RAM VCR, Microwave oven, Micro computer Memory equipped device Back-up for 1 hour or less 50 ma and below Driving motor VCR, Printer, Projector Video disk FT series FS series Subsidiary power supply for driving motor during voltage drop Camera Back-up for 10 seconds or less 1 A and below Power source of toys, LED, buzzer High current supply for a short amount of time Toys, Display device, Alarm device Actuator, Relay solenoid, Gas igniter FA series FE series Power assist Up to several A Power supply, Subsidiary power supply Street sign, Display light, UPS HV series 6 Super Capacitors Vol.14

7 5. Part Number System FM, FC, FT, FG, FS, FR, FY, FE, FA Series FG Series bulk type FG 0H 223 Z F Environmental pollutant reduced tolerance +80%, -20% Nominal capacitance(μf) First two digits represent significant figure Third digit specifies number of zeroes to follow microfarad code. Maximum operating voltage 0V:3.5Vdc, 0H:5.5Vdc, 0J:6.5Vdc, 1A:11Vdc, 1B:12Vdc Series name FM Series tape type (Ammo pack) FM0H223ZF TP 18 Height (excluding lead) 18:18mm Tape type Bulk part name FC Series tape type (Embossed tape) FC0H105ZF TB R 44 - SS Indivisual management code Tape width Positive electrode position in relation to tapes forward direction Embossed tape type Bulk part name Super Capacitors Vol.14 7

8 HV Series (HVZ Type) HVZ 0E 106 N F Environmental pollutant reduced tolerance ±30% Nominal capacitance(μf) First two digits represent significant fifure Third digit specifies number of zeroes to follow microfarad code. Maximum operating voltage 0E:2.7Vdc(50F : 2.5 Vdc) Series name (Type name) 8 Super Capacitors Vol.14

9 6. Rated Specifications 6.1 FC Series Features Dimensions Enables surface mounting. High rated voltage of 5.5V. High leakage reliability. H max. L D±0.5 A±0.2 Negative terminal B±0.2 W±0.1 Markings K I P I Positive terminal Displays nominal capacitance, operating voltage serial number, polarity and etc. Polarity (negative) V A1 S FCS0H473ZFTBR24 FCS0H104ZFTBR24 FCS0H224ZFTBR24 FCS0V104ZFTBR24 FCS0V224ZFTBR24 FCS0V474ZFTBR24 Nominal capacitance operating voltage FCS Type Date code Series name Polarity (negative) Date code Logo N T FC 5.5V 474 A1-001 Nominal capacitance Serial number FC0H474ZFTBR32-SS FC0H105ZFTBR44-SS operating voltage Polarity (negative) V A1 FC0H473ZFTBR24 FC0H104ZFTBR24 FC0H224ZFTBR24 FC0V104ZFTBR24 FC0V224ZFTBR24 FC0V474ZFTBR24 Nominal capacitance operating voltage Date code Standard models FCS Type Part Number Max. Operating Voltage (Vdc) Nominal Discharge system (F) Max. (at 1kHz) ( ) Max. current at 30 minutes (ma) Voltage Holding Characteristic Min. (V) Dimension (Unit:mm) D H A B I W P K L FCS0H473ZFTBR FCS0H104ZFTBR FCS0H224ZFTBR FCS0V104ZFTBR FCS0V224ZFTBR FCS0V474ZFTBR FC Type Part Number Max. Operating Voltage (Vdc) Nominal Discharge system (F) Max. (at 1kHz) ( ) Max. current at 30 minutes (ma) Voltage Holding Characteristic Min. (V) Dimension (Unit:mm) D H A B I W P K L FC0H473ZFTBR FC0H104ZFTBR FC0H224ZFTBR FC0H474ZFTBR32-SS FC0H105ZFTBR44-SS FC0V104ZFTBR FC0V224ZFTBR FC0V474ZFTBR Weight (g) Weight (g) Super Capacitors Vol.14 9

10 Precautions for use This series is exclusively for refl ow soldering. It is designed for thermal conduction system such as combination use of infrared ray and heat blow. Consult with NEC TOKIN before applying other methods. The refl ow condition must be kept within refl ow profi le graphs shown below. Applying refl ow soldering is limited to 2 times. After the first refl ow, cool down the capacitor thoroughly to 5-35 before the second refl ow. Always consult with NEC TOKIN when applying refl ow soldering in a more severe condition than the condition described here. FCS Type FC Type Reflow profile 300 Reflow profile Temperature on the capacitor top 250 Peak temperature Peak temperature : 235,within 10sec. Temperature ( ) sec sec Temperature on the capacitor top ( ) sec Tp Time exceeding Time (sec) 0 Time (sec) Above "Reflow Profile" graph indicates temperature at the terminals and capacitor top. Peak temperature Over 255 Over 230 Over 220 Over 217 Time between 150 to 200 temperature zone over 170 within 50sec. Below 260 Within 10sec. Within 45sec. Within 60sec. Within 70sec. 150sec. Peak temperature ( ) Tp Time exceeding Tp (sec) Above "Reflow Profile" graph indicates temperature at the terminals and capacitor top. 10 Super Capacitors Vol.14

11 Tape and Reel Dimensions [Reel Dimensions] (mm) E C B Mark TBR24 TBR32 TBR44 A B Product height 5.5mm 80 1 Product height 8.5mm R:10 D C D E A W t W Product height 5.5mm Product height 8.5mm t Dimensions of indented [square-hole plastic tape] TBR24 t1 t2 Sprocket hole A B Super capacitors fitting on square-hole P2 Indented square-hole for fitting super capacitors P0 P1 φd0 F E Forward direction W (mm) Mark TBR24 TBR32 TBR44 W A B P P P TBR32/44 t1 P2 P0 φd0 F D A F E t E G B W t2 Product height 5.5mm 6.0 Product height 8.5mm G t2 Super capacitors fitting on square-hole P1 R Recommended land pattern Land pattern Lead terminal C (mm) Part Number A B C FCS0H473ZFTBR FCS0H104ZFTBR FCS0H224ZFTBR FCS0V104ZFTBR FCS0V224ZFTBR FCS0V474ZFTBR (mm) Part Number A B C FCS0H473ZFTBR FCS0H104ZFTBR FCS0H224ZFTBR FCS0V104ZFTBR FCS0V224ZFTBR FCS0V474ZFTBR Logo B A B FC0H473ZFTBR FC0H104ZFTBR FC0H224ZFTBR FC0H474ZFTBR32-SS FC0H105ZFTBR44-SS FC0V104ZFTBR FC0V224ZFTBR FC0V474ZFTBR FC0H473ZFTBR FC0H104ZFTBR FC0H224ZFTBR FC0H474ZFTBR32-SS FC0H105ZFTBR44-SS FC0V104ZFTBR FC0V224ZFTBR FC0V474ZFTBR Super Capacitors Vol.14 11

12 Specifications Item Category temperature range operating voltage Series name 25 to Vdc, 3.5Vdc FC, FCS 5.5V type, 3.5V type Test conditions (conforming to JIS C ) Refer to standard ratings Refer to Measurement Conditions allowance 80, 20 Refer to Measurement Conditions Refer to standard ratings Measured at 1kHz, 10mA ; See also Measurement Conditions Current (30-minutes value) Refer to standard ratings Refer to Measurement Conditions * Surge * Characteristics in different temperature * Vibration resistance * Solder heat resistance * Temperature cycle * High temp. and high humidity resistance * High temperature load * Self discharge characteristics (voltage holding characteristics) More than 90% of initial specifi ed value Surge voltage 4.0V (3.5V type, 3.6V type) Less than 120% of initial specifi ed value 6.3V (5.5V type) Charge 30 sec. Less than 120% of initial specifi ed value Discharge 9min 30sec. Number of cycles 1000 Series resistance 0.047F F F F F 15 Discharge resistance 0 Temperature 70 2 More than 50% of initial measured value Phase 2 Less than 400% of initial measured value Phase 3 Conforms to 4.17 Phase Less than 200% of initial measured value Phase Phase 5 Phase CV (ma) or below Phase Within 20% of initial measured value Phase Phase 6 Conforms to 4.13 Frequency 10 to 55 Hz Testing time 6 hours Within 20% of initial measured value Less than 120% of initial specifi ed value Less than 120% of initial specifi ed value Within 30% of initial measured value Less than 200% of initial specifi ed value Less than 200% of initial specifi ed value 5.5V type: Voltage between terminal leads higher than 4.2V 3.5V type: Not specifi ed Cooled down to ambient temperature after refl ow soldering, then the product must fulfi ll the condition stated left. (See page 10 for refl ow condition) Conforms to 4.12 Temperature condition 25 Room temperature 70 Room temperature Number of cycles 5 Cycles Conforms to 4.14 Temperature 40 2 Relative humidity 90 to 95 RH Testing time hours Conforms to 4.15 Voltage applied operating voltage Series protection resistance 0 Testing time Hours Charging condition Storage As for items with *, it must fulfill the above condition after the refl ow soldering. (See page 10 for refl ow conditions) Voltage applied 5.0Vdc (Terminal at the case's side be negative) Series resistance 0 Charging time 24 hours Let stand for 24 hours in condition described below with terminals opened. Ambient temperature Lower than 25 Relative humidity Lower than 70%RH 12 Super Capacitors Vol.14

13 6.2 FM Series Dimensions 10.5±0.5 T± ± ±0.1 5±1 0.5± ±0.1 5±0.5 Unit mm Markings Negative polarity identification operating voltage 5.5V 473 N T A1 E + Nominal capacitance E :FME type marking R :FMR type marking Polarity Date code Lead terminal forming example Lead length designation For transverse mounting <L1> Ask us about dimensions. L=2.2 to 5mm Super Capacitors Vol.14 13

14 Specifications 5.5V Type Bulk Part Number Ammo pack operating voltage Vdc Nominal capacitance Charge system(f) Discharge system(f) at 1 khz current at 30 min. ma Voltage holding characteristics V T mm FM0H103ZF FM0H103ZFTP FM0H223ZF FM0H223ZFTP FM0H473ZF FM0H473ZFTP FM0H104ZF FM0H104ZFTP FM0H224ZF FM0H224ZFTP V Type Bulk Part Number Ammo pack operating voltage Vdc Nominal capacitance Charge system(f) Discharge system(f) at 1 khz current at 30 min. ma T mm FM0V473ZF FM0V473ZFTP FM0V104ZF FM0V104ZFTP FM0V224ZF FM0V224ZFTP V Type Bulk Part Number Ammo pack operating voltage Vdc Nominal capacitance Charge system(f) Discharge system(f) at 1 khz current at 30 min. ma T mm FM0J473ZF FM0J473ZFTP FME Type (Buckup Large Current, ma Order) Bulk Part Number Ammo pack operating voltage Vdc Nominal capacitance Charge system(f) Discharge system(f) at 1 khz current at 30 min. ma T mm FME0H223ZF FME0H223ZFTP FME0H473ZF FME0H473ZFTP FMR Type ( Operating Temperature 85 Type) Bulk Part Number Ammo pack operating voltage Vdc Nominal capacitance Charge system(f) Discharge system(f) at 1 khz current at 30 min. ma Voltage holding characteristics V T mm Weight g Weight g Weight g Weight g FMR0H473ZF FMR0H473ZFTP FMR0H104ZF FMR0H104ZFTP FMR0V104ZF FMR0V104ZFTP Weight g 14 Super Capacitors Vol.14

15 FMC Type Chip parts applicable to treatment in bond hardening furnace (160 5 for seonds) Dimensions b ±0.5 T±0.5 a ± ±0.1 5±1 d1 ±0.1 d2 ±0.1 5±0.5 Unit mm Markings Negative polarity identification operating voltage 5.5V 473 N T K1 C + Nominal capacitance C:FMC type marking Polarity Date code Specifications Bulk Part Number Ammo pack operating voltage Vdc Nominal capacitance Charge system(f) Discharge system(f) at 1 khz current at 30 min. ma Voltage holding characteristics V FMC0H473ZF FMC0H473ZFTP FMC0H104ZF FMC0H104ZFTP FMC0H334ZF FMC0H334ZFTP a (mm) b (mm) T (mm) d1 (mm) d2 (mm) Weight g Super Capacitors Vol.14 15

16 Taping Specification [except FMC0H334ZFTP18] P2 P Δh b c W2 L W1 a P1 F W4 H t 3 W0 W t 2 P0 D 0 t 1 Unit mm Item Symbol Value Tolerance Remarks Component Height a Component Width b Component Thickness c V type : 5.0/0.010F to 0.047F, 6.5/0.047F 3.5 V type : 5.0/0.047F to 0.10F, 6.5/0.22F FME type : 5.0/0.022F to 0.047F 6.5 V type : 6.5/0.047F, 0.10F FMR type : 6.5/0.047F FMC type : 5.0/0.047F, 6.5/0.10F Lead-wire Width W Lead-wire Thickness t Pitch between Component P Sprocket Hole Pitch P Sprocket Hole to Lead P P Lead Spacing F Component Alignment h 2.0 Max. Including tilting caused by bending lead wire. Tape Width W Hold-down tape Width W Min. Sprocket Hole Position W Hold-down Tape Position W2 3.0 Max. No protrusion of tape. Component's Bottom Line Position H Sprocket Hole Diameter D Total tape Thickness t t2 1.5 Max. Defect Component Cut-off Position L 11.0 Max. 16 Super Capacitors Vol.14

17 Taping Specification [FMC0H334ZFTP18] P2 P Δh b c P1 F W2 W4 t 3 H W0 W W1 L a t 2 P0 D 0 t 1 Item Symbol Value Tolerance Remarks Component Height a Component Width b Component Thickness c Lead-wire Width W Lead-wire Thickness t Pitch between Component P Sprocket Hole Pitch P Sprocket Hole to Lead P P Lead Spacing F Component Alignment h 2.0 Max. Including tilting caused by bending lead wire Tape Width W Hold-down tape Width W Min. Sprocket Hole Position W Hold-down Tape Position W2 3.0 Max. No protrusion of tape Component's Bottom Line Position H Sprocket Hole Diameter D Total tape Thickness t t2 1.7 Max. Defect Component Cut-off Position L 11.0 Max. Unit mm Super Capacitors Vol.14 17

18 Specifications Series name 5.5V type, 3.5V type, 6.5V type Test conditions FME type Item FMC type (conforming to JIS C ) Category temperature range 25 to to 70 operating voltage 5.5Vdc, 3.5Vdc, 6.5Vdc 5.5Vdc 5.5V 0.010F to 0.33F 3.5V 0.047F to 0.22F 0.022F, 0.033F, 0.047F Refer to Measurement Conditions 6.5V allowance 80, 20 80, 20 Refer to Measurement Conditions Refer to standard ratings Refer to standard ratings Measured at 1kHz, 10mA ; See also Measurement Conditions Current (30-minutes value) Refer to standard ratings Refer to standard ratings Refer to Measurement Conditions More than 90% of initial specified value More than 90% of initial specified value Surge voltage 4.0V (3.5V type) Less than 120% of initial specifi ed value Less than 120% of initial specifi ed value 6.3V (5.5V type) 7.4V (6.5V type) Less than 120% of initial specifi ed value Less than 120% of initial specifi ed value Charge 30 sec. Discharge 9min 30sec. Number of cycles 1000 Series resistance 0.010F 1500 Surge 0.022F F F F F F F 51 Discharge resistance 0 Temperature 70 2 Phase More than 50% of initial measured value Phase More than 50% of initial measured value 2 Less than 400% of initial measured value 2 Less than 400% of initial measured value Phase Phase Conforms to Phase Characteristics Less than 200% of initial measured value Less than 200% of initial measured value Phase in different Phase Phase Phase temperature Satisfy initial specified value Satisfy initial specified value CV (ma) or below 1.5CV (ma) or below Phase Phase Within 20% of initial measured value Within 20% of initial measured value Phase Phase Satisfy initial specified value Satisfy initial specified value 6 6 Satisfy initial specified value Satisfy initial specified value Lead strength (tensile) No terminal damage No terminal damage Conforms to 4.9 Vibration resistance Solderability Solder heat resistance Temperature cycle High temp. and high humidity resistance High temperature load Self discharge characteristics (voltage holding characteristics) Conforms to 4.13 Frequency 10 to 55 Hz Testing time 6 hours Over 3/4 of the terminal should be covered by the new solder Over 3/4 of the terminal should be covered by the new solder Within 20% of initial measured value Within 20% of initial measured value Less than 120% of initial specifi ed value Less than 120% of initial specifi ed value Less than 120% of initial specifi ed value Less than 120% of initial specifi ed value Within 30% of initial measured value Within 30% of initial measured value Conforms to 4.15 Less than 200% of initial specifi ed value Less than 200% of initial specifi ed value Less than 200% of initial specifi ed value Less than 200% of initial specifi ed value 5.5V type: Voltage between terminal leads higher than 4.2V 3.5V type: Not specifi ed 6.5V type: Not specifi ed Conforms to 4.11 Solder temp Dipping time sec. 1.6mm from the bottom should be dipped. Conforms to 4.10 Solder temp Dipping time 10 1 sec. 1.6mm from the bottom should be dipped. Conforms to 4.12 Temperature condition 25 Room temperature 70 Room temperature Number of cycles 5 Cycles Conforms to 4.14 Temperature 40 2 Relative humidity 90 to 95 RH Testing time hours Temperature 70 2 Voltage applied operating voltage Series protection resistance 0 Testing time Hours Charging condition Storage Voltage applied 5.0Vdc (Terminal at the case's side be negative) Series resistance 0 Charging time 24 hours Let stand for 24 hours in condition described below with terminals opened. Ambient temperature Lower than 25 Relative humidity Lower than 70%RH 18 Super Capacitors Vol.14

19 Specifications Series name Item FMR type Test conditions (conforming to JIS C ) Category temperature range 40 to 85 operating voltage 5.5Vdc, 3.5Vdc 0.047F, 0.10F Refer to Measurement Conditions allowance 80, 20 Refer to Measurement Conditions Refer to standard ratings Measured at 1kHz, 10mA ; See also Measurement Conditions Current (30-minutes value) Refer to standard ratings Refer to Measurement Conditions More than 90% of initial specifi ed value Surge voltage 4.0V (3.5V type) Less than 120% of initial specifi ed value 6.3V (5.5V type) Charge 30 sec. Less than 120% of initial specifi ed value Discharge 9min 30sec. Surge Number of cycles 1000 Series resistance 0.047F F 150 Discharge resistance 0 Temperature 85 2 More than 50% of initial measured value Phase 2 Less than 400% of initial measured value More than 30% of initial measured value Conforms to 4.17 Phase 3 Less than 700% of initial measured value Phase Phase Characteristics in Less than 200% of initial measured value Phase different temperature Phase 5 Phase CV (ma) or below Phase Within 20% of initial measured value Phase Phase 6 Lead strength (tensile) No terminal damage Conforms to 4.9 Conforms to 4.13 Vibration resistance Frequency 10 to 55 Hz Testing time 6 hours Solderability Solder heat resistance Temperature cycle High temp. and high humidity resistance High temperature load Self discharge characteristics (voltage holding characteristics) Over 3/4 of the terminal should be covered by the new solder Within 20% of initial measured value Less than 120% of initial specifi ed value Less than 120% of initial specifi ed value Within 30% of initial measured value Conforms to 4.15 Less than 200% of initial specifi ed value Less than 200% of initial specifi ed value 5.5V type: Voltage between terminal leads higher than 4.2V 3.5V type: Not specifi ed Conforms to 4.11 Solder temp Dipping time sec. 1.6mm from the bottom should be dipped. Conforms to 4.10 Solder temp Dipping time 10 1 sec. 1.6mm from the bottom should be dipped. Conforms to 4.12 Temperature condition 40 Room temperature 85 Room temperature Number of cycles 5 Cycles Conforms to 4.14 Temperature 40 2 Relative humidity 90 to 95 RH Testing time hours Temperature 85 2 Voltage applied operating voltage Series protection resistance 0 Testing time Hours Charging condition Storage Voltage applied 5.0Vdc (Terminal at the case's side be negative) Series resistance 0 Charging time 24 hours Let stand for 24 hours in condition described below with terminals opened. Ambient temperature Lower than 25 Relative humidity Lower than 70%RH Super Capacitors Vol.14 19

20 6.3 FG Series Dimensions Sleeve φ D ± 0.5 H. lmin. 0.3 MIN. Markings on sleeve Date code Serial number A1 001 A1 FG Super Capacitor 5.5 V FG 5.5 V 0.22 F 0.22 F operating voltage Nominal capacitance P ± (Terminal) FG Type Specifications Part Number operating voltage Vdc d1 ± 0.1 d2 ± 0.1 Nominal capacitance Charge system (F) Discharge system (F) at 1 khz current at 30 min. ma Voltage holding characteristics V Negative polarity identification mark Dimension (unit:mm) D H P d1 d2 FG0H103ZF FG0H223ZF FG0H473ZF FG0H104ZF FG0H224ZF FG0H474ZF FG0H105ZF FG0H225ZF FG0H475ZF FG0V155ZF FGH Type Specifications Part Number operating voltage Vdc Nominal capacitance F at 1 khz current at 30 min. ma Voltage holding characteristics V Dimension (unit:mm) D H P d1 d2 FGH0H104ZF FGH0H224ZF FGH0H474ZF FGH0H105ZF FGR Type Specifications Part Number operating voltage Vdc Nominal capacitance Charge system (F) Discharge system (F) at 1 khz current at 30 min. ma Voltage holding characteristics V Dimension (unit:mm) D H P d1 d2 FGR0H474ZF FGR0H105ZF FGR0H225ZF Weight g Weight g Weight g 20 Super Capacitors Vol.14

21 Specifications Series name Item FG, FGH type FGR type Category temperature range 25 to to 85 Test conditions (conforming to JIS C ) operating voltage 5.5Vdc, 3.5Vdc 5.5Vdc FG 0.010F to 4.7F FGH 0.10F to 1.0F 0.47F to 2.2F Refer to Measurement Conditions allowance 80, 20 80, 20 Refer to Measurement Conditions Refer to standard ratings Refer to standard ratings Measured at 1kHz, 10mA ; See also Measurement Conditions Current (30-minutes value) Refer to standard ratings Refer to standard ratings Refer to Measurement Conditions More than 90% of initial specified value More than 90% of initial specified value Surge voltage 6.3V (5.5V type) Less than 120% of initial specifi ed value Less than 120% of initial specifi ed value 4.0V(3.5V type) Charge 30 sec. Less than 120% of initial specifi ed value Less than 120% of initial specifi ed value Discharge 9min 30sec. Number of cycles 1000 Series resistance 0.010F F 560 Surge 0.047F F F F F, 1.5F F, 4.7F 10 Discharge resistance 0 Temperature 85 2 (FGR) 70 2 (FG, FGH) Phase More than 50% of initial measured value Phase More than 50% of initial measured value 2 Less than 400% of initial measured value 2 Less than 400% of initial measured value Phase Phase More than 30% of initial measured value Conforms to 4.17 Phase Less than 700% of initial measured value Phase Characteristics Less than 200% of initial measured value Less than 200% of initial measured value Phase (FGR) in different Phase Phase Phase temperature Satisfy initial specified value Satisfy initial specified value 5 5 Phase (FG, FGH) 1.5CV (ma) or below 1.5CV (ma) or below 85 2 (FGR) Within 20% of initial measured value Within 20% of initial measured value Phase Phase Phase Satisfy initial specified value Satisfy initial specified value 6 6 Satisfy initial specified value Satisfy initial specified value Lead strength (tensile) No terminal damage No terminal damage Conforms to 4.9 Vibration Conforms to 4.13 Frequency 10 to 55 Hz resistance Testing time 6 hours Solderability Solder heat resistance Temperature cycle High temp. and high humidity resistance High temperature load Self discharge characteristics (voltage holding characteristics) Over 3/4 of the terminal should be covered by the new solder Over 3/4 of the terminal should be covered by the new solder Within 20% of initial measured value Within 20% of initial measured value Less than 120% of initial specifi ed value Less than 120% of initial specifi ed value Less than 120% of initial specifi ed value Less than 120% of initial specifi ed value Within 30% of initial measured value Within 30% of initial measured value Conforms to 4.15 Less than 200% of initial specifi ed value Less than 200% of initial specifi ed value Less than 200% of initial specifi ed value Less than 200% of initial specifi ed value 5.5V type: Voltage between terminal leads higher than 4.2V 3.5V type: Not specifi ed Voltage between terminal leads higher than 4.2V Conforms to 4.11 Solder temp Dipping time sec. 1.6mm from the bottom should be dipped. Conforms to 4.10 Solder temp Dipping time 10 1 sec. 1.6mm from the bottom should be dipped. Conforms to 4.12 Temperature condition Category MIN temp Room temp Category temp Room temp Number of cycles 5 Cycles Conforms to 4.14 Temperature 40 2 Relative humidity 90 to 95 RH Testing time hours Temp Category temp 2 Voltage applied operating voltage Series protection resistance 0 Testing time Hours Charging condition Storage Voltage applied 5.0Vdc (Terminal at the case's side be negative) Series resistance 0 Charging time 24 hours Let stand for 24 hours in condition described below with terminals opened. Ambient temperature Lower than 25 Relative humidity Lower than 70%RH Super Capacitors Vol.14 21

22 6.4 FT Series Dimensions Markings on sleeve Sleeve H. φ D ± 0.5 lmin. 0.3 MIN. Date code Serial number A1 001 A1 FT Super Capacitor 5.5 V FT 5.5 V F F operating voltage Nominal capacitance P ± Negative polarity identification mark (Terminal) d1 ± 0.1 d2 ± 0.1 Specifications Part Number operating voltage Vdc Nominal capacitance Charge system (F) Discharge system (F) at 1 khz current at 30 min. ma Dimension (unit:mm) D H P d1 d2 FT0H104ZF FT0H224ZF FT0H474ZF FT0H105ZF FT0H225ZF FT0H335ZF FT0H565ZF Weight g 22 Super Capacitors Vol.14

23 Specifications Item Category temperature range operating voltage Series name 40 to Vdc FT type Test conditions (conforming to JIS C ) 0.1F to 5.6F Refer to Measurement Conditions allowance 80, 20 Refer to Measurement Conditions Refer to standard ratings Measured at 1kHz, 10mA ; See also Measurement Conditions Current (30-minutes value) Refer to standard ratings Refer to Measurement Conditions More than 90% of initial specifi ed value Less than 120% of initial specifi ed value Less than 120% of initial specifi ed value Surge voltage 6.3V Charge 30 sec. Discharge 9min 30sec. Number of cycles 1000 Series resistance 0.10F 0.22F Surge 0.47F 1.0F 2.2F 3.3F 5.6F Discharge resistance 0 Temperature 85 2 More than 50% of initial measured value Phase 2 Less than 400% of initial measured value More than 30% of initial measured value Conforms to 4.17 Phase 3 Less than 700% of initial measured value Phase Phase Characteristics in Less than 200% of initial measured value Phase different temperature Phase 5 Phase CV (ma) or below Phase Within 20% of initial measured value Phase Phase 6 Lead strength (tensile) No terminal damage Conforms to 4.9 Conforms to 4.13 Vibration resistance Frequency 10 to 55 Hz Testing time 6 hours Solderability Solder heat resistance Temperature cycle High temp. and high humidity resistance High temperature load Over 3/4 of the terminal should be covered by the new solder Within 20% of initial measured value Less than 120% of initial specifi ed value Less than 120% of initial specifi ed value Within 30% of initial measured value Conforms to 4.15 Less than 200% of initial specifi ed value Less than 200% of initial specifi ed value Conforms to 4.11 Solder temp Dipping time sec. 1.6mm from the bottom should be dipped. Conforms to 4.10 Solder temp Dipping time 10 1 sec. 1.6mm from the bottom should be dipped. Conforms to 4.12 Temperature condition 40 Room temperature 85 Room temperature Number of cycles 5 Cycles Conforms to 4.14 Temperature 40 2 Relative humidity 90 to 95 RH Testing time hours Temperature 85 2 Voltage applied operating voltage Series protection resistance 0 Testing time Hours Super Capacitors Vol.14 23

24 6.5 FY Series Dimensions Markings on sleeve Sleeve H. φ D ± 0.5 lmin. 0.3 MIN. Date code Serial number A1 001 A1 FYD 5.5 V F FYD 5.5 V F operating voltage Nominal capacitance FYD Type Specifications Part Number P ± (Terminal) operating voltage Vdc d1 ± 0.1 d2 ± 0.1 Nominal capacitance Charge system (F) Discharge system (F) at 1 khz current at 30 min. ma Voltage holding characteristics V Negative polarity identification mark Dimension (unit:mm) D H P d1 d2 FYD0H223ZF FYD0H473ZF FYD0H104ZF FYD0H224ZF FYD0H474ZF FYD0H105ZF FYD0H145ZF FYD0H225ZF FYH Type Specifications Part Number operating voltage Vdc Nominal capacitance Charge system (F) Discharge system (F) at 1 khz current at 30 min. ma Voltage holding characteristics V Dimension (unit:mm) D H P d1 d2 FYH0H223ZF FYH0H473ZF FYH0H104ZF FYH0H224ZF FYH0H474ZF FYH0H105ZF Weight g Weight g 24 Super Capacitors Vol.14

25 Specifications Item Category temperature range operating voltage Series name 25 to Vdc FYD 0.022F to 2.2F FYH 0.022F to 1.0F FY type Test conditions (conforming to JIS C ) Refer to Measurement Conditions allowance 80, 20 Refer to Measurement Conditions Refer to standard ratings Measured at 1kHz, 10mA ; See also Measurement Conditions Current (30-minutes value) Refer to standard ratings Refer to Measurement Conditions Surge Characteristics in different temperature More than 90% of initial specifi ed value Less than 120% of initial specifi ed value Surge voltage 6.3V Charge 30 sec. Discharge 9min 30sec. Less than 120% of initial specifi ed value Number of cycles 1000 Series resistance 0.022F 0.047F 0.068F 0.10F 0.22F 0.47F 1.0F, 1.4F 2.2F Discharge resistance 0 Temperature 70 2 More than 50% of initial measured value Phase 2 Less than 400% of initial measured value Phase 3 Conforms to 4.17 Phase Less than 200% of initial measured value Phase Phase 5 Phase CV (ma) or below Phase Phase Within 20% of initial measured value Phase 6 Lead strength (tensile) No terminal damage Conforms to 4.9 Conforms to 4.13 Vibration resistance Frequency 10 to 55 Hz Testing time 6 hours Solderability Solder heat resistance Temperature cycle High temp. and high humidity resistance High temperature load Self discharge characteristics (voltage holding characteristics) Over 3/4 of the terminal should be covered by the new solder Within 20% of initial measured value Less than 120% of initial specifi ed value Less than 120% of initial specifi ed value Within 30% of initial measured value Conforms to 4.15 Less than 200% of initial specifi ed value Less than 200% of initial specifi ed value Voltage between terminal leads higher than 4.2V Conforms to 4.11 Solder temp Dipping time sec. 1.6mm from the bottom should be dipped. Conforms to 4.10 Solder temp Dipping time 10 1 sec. 1.6mm from the bottom should be dipped. Conforms to 4.12 Temperature condition 25 Room temperature 70 Room temperature Number of cycles 5 Cycles Conforms to 4.14 Temperature 40 2 Relative humidity 90 to 95 RH Testing time hours Temperature 70 2 Voltage applied operating voltage Series protection resistance 0 Testing time Hours Charging condition Storage Voltage applied 5.0Vdc (Terminal at the case's side be negative) Series resistance 0 Charging time 24 hours Let stand for 24 hours in condition described below with terminals opened. Ambient temperature Lower than 25 Relative humidity Lower than 70%RH Super Capacitors Vol.14 25

26 6.6 FR Series Dimensions Markings on sleeve Sleeve H. φ D ± 0.5 lmin. 0.3 MIN. Date code Serial number A1 001 FR 5.5 V F A1 FR 5.5 V F operating voltage Nominal capacitance P ± Negative polarity identification mark (Terminal) d1 ± 0.1 d2 ± 0.1 Specifications Part Number operating voltage Vdc Nominal capacitance Charge system (F) Discharge system (F) at 1 khz current at 30 min. ma Voltage holding characteristics V Dimension (unit:mm) D H P d1 d2 FR0H223ZF FR0H473ZF FR0H104ZF FR0H224ZF FR0H474ZF FR0H105ZF Weight g 26 Super Capacitors Vol.14

27 Specifications Item Category temperature range operating voltage Series name 40 to Vdc FR type Test conditions (conforming to JIS C ) 0.022F to 1.0F Refer to Measurement Conditions allowance 80, 20 Refer to Measurement Conditions Refer to standard ratings Measured at 1kHz, 10mA ; See also Measurement Conditions Current (30-minutes value) Refer to standard ratings Refer to Measurement Conditions More than 90% of initial specifi ed value Less than 120% of initial specifi ed value Less than 120% of initial specifi ed value Surge voltage 6.3V (5.5V type) Charge 30 sec. Discharge 9min 30sec. Number of cycles 1000 Series resistance 0.022F 0.047F Surge 0.068F 0.10F 0.22F 0.47F 1.0F Discharge resistance 0 Temperature 70 2 More than 50% of initial measured value Phase 2 Less than 400% of initial measured value More than 30% of initial measured value Conforms to 4.17 Phase 3 Less than 700% of initial measured value Phase Phase Characteristics in Less than 200% of initial measured value Phase different temperature Phase 5 Phase CV (ma) or below Phase Within 20% of initial measured value Phase Phase 6 Lead strength (tensile) No terminal damage Conforms to 4.9 Conforms to 4.13 Vibration resistance Frequency 10 to 55 Hz Testing time 6 hours Solderability Solder heat resistance Temperature cycle High temp. and high humidity resistance High temperature load Self discharge characteristics (voltage holding characteristics) Over 3/4 of the terminal should be covered by the new solder Within 20% of initial measured value Less than 120% of initial specifi ed value Less than 120% of initial specifi ed value Within 30% of initial measured value Conforms to 4.15 Less than 200% of initial specifi ed value Less than 200% of initial specifi ed value Voltage between terminal leads higher than 4.2V Conforms to 4.11 Solder temp Dipping time sec. 1.6mm from the bottom should be dipped. Conforms to 4.10 Solder temp Dipping time 10 1 sec. 1.6mm from the bottom should be dipped. Conforms to 4.12 Temperature condition 40 Room temperature 85 Room temperature Number of cycles 5 Cycles Conforms to 4.14 Temperature 40 2 Relative humidity 90 to 95 RH Testing time hours Temperature 85 2 Voltage applied operating voltage Series protection resistance 0 Testing time Hours Charging condition Storage Voltage applied 5.0Vdc (Terminal at the case's side be negative) Series resistance 0 Charging time 24 hours Let stand for 24 hours in condition described below with terminals opened. Ambient temperature Lower than 25 Relative humidity Lower than 70%RH Super Capacitors Vol.14 27

28 6.7 FS Series Dimensions Markings on sleeve Sleeve H. φ D ± 0.5 P ± lmin. 0.3 MIN. Date code Serial number A1 001 A1 FS 5.5 V FS 5.5 V 0.22 F 0.22 F Negative polarity identification mark operating voltage Nominal capacitance Specifications Part Number (Terminal) operating voltage Vdc d1 ± 0.1 d2 ± 0.1 Nominal capacitance Charge system (F) Discharge system (F) at 1 khz current at 30 min. ma Dimension (unit:mm) D H P d1 d2 FS0H223ZF FS0H473ZF FS0H104ZF FS0H224ZF FS0H474ZF FS0H105ZF FS1A474ZF FS1A105ZF FS1B105ZF FS1B505ZF Weight g 28 Super Capacitors Vol.14

29 Specifications Series name Item FS type Test conditions (conforming to JIS C ) Category temperature range 25 to 70 operating voltage 5.5Vdc, 11Vdc, 12Vdc 5.5V 0.022F to 1.0F 11V 0.47, 1.0 Refer to Measurement Conditions 12V 1.0F, 5.0F allowance 80, 20 Refer to Measurement Conditions Refer to standard ratings Measured at 1kHz, 10mA ; See also Measurement Conditions Current (30-minutes value) Refer to standard ratings Refer to Measurement Conditions More than 90% of initial specifi ed value Surge voltage 6.3V (5.5V type) Less than 120% of initial specifi ed value 12.6V (11V type) Less than 120% of initial specifi ed value 13.6V (12V type) Charge 30 sec. Discharge 9min 30sec. Number of cycles 1000 Series resistance 0.022F 560 Surge 0.047F F F F F F 10 Discharge resistance 0 Temperature 70 2 More than 50% of initial measured value Phase 2 Less than 400% of initial measured value Phase 3 Conforms to 4.17 Phase Characteristics in Less than 200% of initial measured value Phase different temperature Phase 5 Phase CV (ma) or below Phase Within 20% of initial measured value Phase Phase 6 Lead strength (tensile) No terminal damage Conforms to 4.9 Conforms to 4.13 Vibration resistance Frequency 10 to 55 Hz Testing time 6 hours Solderability Solder heat resistance Temperature cycle High temp. and high humidity resistance High temperature load Over 3/4 of the terminal should be covered by the new solder Conforms to 4.11 Solder temp Dipping time sec. 1.6mm from the bottom should be dipped. Conforms to 4.10 Solder temp Dipping time 10 1 sec. 1.6mm from the bottom should be dipped. Conforms to 4.12 Temperature condition 25 Room temperature 70 Room temperature Number of cycles 5 Cycles More than 90% of initial specified value (5.5V type) Within 20% of initial measured value (11V type, 12Vtype) Conforms to 4.14 Less than 120% of initial specifi ed value Temperature 40 2 Relative humidity 90 to 95 RH Less than 120% of initial specifi ed value Testing time hours More than 85% of initial specified value (5.5V type) Within 20% of initial measured value (11V type, 12Vtype) Less than 200% of initial specifi ed value Less than 200% of initial specifi ed value Conforms to 4.15 Temperature 70 2 Voltage applied operating voltage Series protection resistance 0 Testing time Hours Super Capacitors Vol.14 29

30 6.8 FA Series, FE Series FA Series Dimensions Markings on sleeve φ D ± 0.5 H. l Date code Serial number A1 001 A1 001 FA FA 5 V 0.1 F 5 V 0.1 F FA FA 5 V 0.1 F 5 V 0.1 F Rated voltage Nominal capacitance Sleeve Specifications Part Number Sleeve operating voltage Vdc FE Series Dimensions H. P ± d1 ± 0.1 d2 ± 0.1 (Terminal) Rated voltage Vdc φ D ± 0.5 P ± lmin. d1 ± 0.1 d2 ± 0.1 (Terminal) Nominal capacitance Charge system (F) 0.3 MIN. Discharge system (F) at 1 khz Date code Serial number current at 30 min. ma Markings on sleeve A1 001 A1 FE 5.5 V F FE Negative polarity identification mark Dimension (unit:mm) D H P d1 d2 FA0H473ZF FA0H104ZF FA0H224ZF FA0H474ZF FA0H105ZF FA1A223ZF FA1A104ZF FA1A224ZF FA1A474ZF Specifications Part Number operating voltage Vdc Nominal capacitance Charge system (F) Discharge system (F) at 1 khz current at 30 min. ma 5.5 V F Negative polarity identification mark Dimension (unit:mm) Weight g operating voltage Nominal capacitance D H P d1 d2 FE0H473ZF FE0H104ZF FE0H224ZF FE0H474ZF FE0H105ZF FE0H155ZF Weight g 30 Super Capacitors Vol.14

31 Specifications Series name Test conditions FA FE Item (conforming to JIS C ) Category temperature range 25 to to 70 operating voltage 5.5Vdc, 11Vdc 5.5Vdc 5.5V 0.047F to 1.0F 11V 0.022F to 0.47F 0.047F to 1.5F Refer to Measurement Conditions allowance 80, 20 80, 20 Refer to Measurement Conditions Refer to standard ratings Refer to standard ratings Measured at 1kHz, 10mA ; See also Measurement Conditions Current (30-minutes value) Refer to standard ratings Refer to standard ratings Refer to Measurement Conditions More than 90% of initial specified value Surge voltage 6.3V (5.5V type) Less than 120% of initial specifi ed value 12.6V (11V type) Charge 30 sec. Less than 120% of initial specifi ed value Discharge 9min 30sec. Surge Number of cycles 1000 Series resistance 0.047F 0.22F F 0.47F F, 1.5F 15 Discharge resistance 0 Temperature 70 2 Phase More than 70% of initial measured value Phase 2 Less than 300% of initial measured value 2 Phase Phase More than 40% of initial measured value Conforms to Less than 400% of initial measured value Phase Characteristics Less than 150% of initial measured value Less than 200% of initial measured value Phase in different Phase Phase Phase (FE type) temperature Satisfy initial specified value Satisfy initial specified value 5 5 Phase CV (ma) or below 1.5CV (ma) or below Phase Within 20% of initial measured value Within 20% of initial measured value Phase Phase Phase Satisfy initial specified value 6 6 Satisfy initial specified value Satisfy initial specified value Satisfy initial specified value Lead strength (tensile) No terminal damage No terminal damage Conforms to 4.9 Vibration Conforms to 4.13 Frequency 10 to 55 Hz resistance Testing time 6 hours Solderability Solder heat resistance Temperature cycle High temp. and high humidity resistance High temperature load Over 3/4 of the terminal should be covered by the new solder Over 3/4 of the terminal should be covered by the new solder More than 90% of initial specified value Within 20% of initial measured value Less than 120% of initial specifi ed value Less than 120% of initial specifi ed value Less than 120% of initial specifi ed value Less than 120% of initial specifi ed value More than 85% of initial specified value Within 30% of initial measured value Conforms to 4.15 Less than 120% of initial specifi ed value Less than 300% of initial specifi ed value Less than 200% of initial specifi ed value Less than 200% of initial specifi ed value Conforms to 4.11 Solder temp Dipping time sec. 1.6mm from the bottom should be dipped. Conforms to 4.10 Solder temp Dipping time 10 1 sec. 1.6mm from the bottom should be dipped. Conforms to 4.12 Temperature condition 25 ( 40 for FE type) Room temperature 70 Room temperature Number of cycles 5 Cycles Conforms to 4.14 Temperature 40 2 Relative humidity 90 to 95 RH Testing time hours Temperature 70 2 Voltage applied operating voltage Series protection resistance 0 Testing time Hours Super Capacitors Vol.14 31