4mm Surface Mount, Single-Turn, Sealed Cermet Trimmers
|
|
- Leslie Goodwin
- 5 years ago
- Views:
Transcription
1 Effective Date April 5 TOCOS POTENTIOMETERS 4mm Surface Mount, Single-Turn, Sealed Cermet Trimmers RoHS Compliant IMPROVED DESIGN Pb-Free and Cd-Free Features 4mm square SMD, single-turn, sealed cermet trimmers Available in J-hook and gull-wing terminal configurations Meets EIA, EIAJ, IPC, VECI standard SMD trimmer designs Pb-free and Cd-free construction RoHS compliant Gold-plated leads provide high conductivity, low contact resistance, high corrosion resistance and good solderability Top, side or bottom cross-slot adjustment High setting accuracy, zero backlash Tape and reel packaging Specifications Electrical Standard Resistance Range Ω to 2MΩ (standard 1, 2 & 5 sequence) Resistance Tolerance % standard End Resistance % or 3Ω, whichever is greater Resistance Taper B = Linear Peak Noise (C.R.V.) % or 3Ω, whichever is greater Power Rating watt at 70 C; 0 watt at 125 C Maximum Input Voltage VDC or power rating, whichever is smaller Temperature Coefficient.... ppm/ C, Ω to 1MΩ 2ppm/ C, other values Insulation Resistance MΩ minimum at VDC Dielectric Strength VAC, 1 minute Adjustment Travel Mechanical Mechanical Travel Shaft Torque gf cm (2.08 oz in) max. Stop Strength gf cm (4.16 oz in) min. Flammability of Plastic Materials Meets UL 94V-0 Nominal Weight g (A, B, D, E) 0.16g (BF); 0.24g (SA) Marking Resistance code, date code For through-hole models of the G43 series, refer to the G43C Series. Environmental Temperature Range C to 125 C Low Temperature Exposure C, 0.25 watt, 45 minutes T/R ) 2%, S.S. ) 2% High Temperature Exposure C, 2 hours T/R ) 2%, S.S. ) 2% Load Life C, 0.25 watt, hours T/R ) 3%, S.S. ) 2% Thermal Shock C, 125 C, 30 minutes each, 5 cycles T/R ) 2%, S.S. ) 1% Shock G, 6ms, 6 directions, 3 times each T/R ) 1%, S.S. ) 1% Vibration Hz, 1.5mm amplitude, G, 12 hours T/R ) 1%, S.S. ) 1% Humidity C, 90-95%RH, 0.25 watt, hours T/R ) 3%, S.S. ) 2% Moisture Resistance C to 65 C, 80-98%RH, 0.25 watt, cycles, 240 hours T/R ) 3% Soldering Heat Resistance C, seconds T/R ) 1% Seal Test C, hot water for 1 minute Rotational Life.... cycles without discontinuity, no load T/R ) 5% T/R = Total Resistance Change; S.S. = Setting Stability (voltage ratio) 1/8
2 All A, B, D & E Models Position of Rotor Inside Standard and Reverse Markings Standard Markings Outside Positions Reverse Markings Outside Positions Effective Date April 5 Position of the rotor inside is the same for both types of markings. G43A & G43B G43D & G43E The D and E models are the same construction as the A and B models. The only difference is the reversed outside markings. Dimensions G43A J-Hook, Top Adjust All G43 models: Cross-Slot accepts both Philips and single blade adjustment tools (0.35) , 0 (0.35) G43D Reverse Markings, J-Hook, Top Adjust (0.35) , 0 (0.35) G43SA J-Hook, Side Adjust , (0.8) (1.5) (1.1) (1.85) (1.95) (2) 0.6 (0.55) 3.18 (0.05) (0.22) , 2/8
3 Dimensions Effective Date April 5 G43B Gull-Wing, Top Adjust (1.0) , 0 (1.0) G43E Reverse Markings, Gull-Wing, Top Adjust (1.0) , 0 (1.0) G43BF Gull-Wing, Bottom Adjust 5.0 (0.6) (1.1) (0.5) (2) (1.1) , 0 Cross-Slot Dimensions Electrical Schematic All G43 Models clockwise 0.55 Ø 1.9 ccw cw Ø wiper Cross-Slot accepts both Philips and single blade adjustment tools. 3/8
4 Recommended Land Patterns Soldering Dimensions Guidelines Effective Date April 5 Flow or Reflow Soldering Methods G43A, G43D G43B, G43E G43BF Ø Flow Soldering Method G43SA Reflow Soldering Method G43SA Recommended Soldering Profiles Flow Soldering Profile Reflow Soldering Profile 2 TP 260 C Max. Peak Temp. TM 230 C Solder Melting Temp. 2 TP 260 C Max. Peak Temp. TM 230 C Solder Melting Temp. Temperature ( C) 1 (180 C) (140 C) ts.* 5 sec. Solder Melting Time Temperature ( C) 1 (190 C) (170 C) Pre-Heat Zone 2 min. ts.*40 sec. Solder Melting Time Time (min.) Time (min.) 4/8
5 Tape & Reel Specifications Effective Date April 5 Embossed Tape Dimensions Conforms to EIA-481, JIS-C-0806 and EIAJ-RC-9B G43AT, G43DT, G43BT, G43ET Ø1.5, Ø1.6 Direction of Feed G43SAT Ø1.5, Ø Direction of Feed Reel Dimensions Conforms to EIA-481, JIS-C-0806 and EIAJ-RC-9B G43AT, G43DT, G43BT, G43ET G43SAT Ø Ø Ø Ø Ø , 0 Ø Ø Pieces Per 7 Reel Ø Pieces Per Reel 5/8
6 G43 A T B 2 M Part Numbering System Effective Date April 5 Resistance Tolerance: M = % standard. Resistance Code: Expressed in ohms. A three digit code where the first two digits are significant figures, and the third digit indicates the number of zeros that follow these figures (i.e., = Ω; 1 = Ω; 2 = Ω; 5 =,000Ω). Resistance Taper: B = Linear. Packaging: T (T1 for SA) = Tape & Reel; Blank = Bulk. Terminal Style: A, D, SA = J-Hook; B, BF, E = Gull-Wing. TOCOS Series Name. Part Numbers Value (Ω) Nominal Resistance Code Resistance Tolerance % Tape & Reel Bulk Potentiometer Styles G43A J-Hook, Top Adjust,000,000,000,000,000, G43ATBM G43AT B M G43AT B M G43AT B 1 M G43AT B 1 M G43AT B 1 M G43ATB2M G43AT B 2 M G43AT B 2 M G43ATB3M G43AT B 3 M G43AT B 3 M G43ATB4M G43AT B 4 M G43AT B 4 M G43A B M G43A B M G43A B M G43A B 1 M G43A B 1 M G43A B 1 M G43A B 2 M G43A B 2 M G43A B 2 M G43A B 3 M G43A B 3 M G43A B 3 M G43A B 4 M G43A B 4 M G43A B 4 M 5 G43ATB5M G43A B 5 M 5 G43AT B 5 M G43A B 5 M G43A G43D Reverse Markings, J-Hook, Top Adjust,000,000,000,000,000, G43DT B M G43DT B M G43DT B M G43DT B 1 M G43DT B 1 M G43DT B 1 M G43DT B 2 M G43DT B 2 M G43DT B 2 M G43DT B 3 M G43DT B 3 M G43DT B 3 M G43DT B 4 M G43DT B 4 M G43DT B 4 M G43DT B 5 M G43DT B 5 M G43D B M G43D B M G43D B M G43D B 1 M G43D B 1 M G43D B 1 M G43D B 2 M G43D B 2 M G43D B 2 M G43D B 3 M G43D B 3 M G43D B 3 M G43D B 4 M G43D B 4 M G43D B 4 M G43D B 5 M G43D B 5 M G43D 6/8
7 Nominal Resistance Value (Ω) Code Part Numbers Resistance Tolerance % Tape & Reel Bulk Effective Date April 5 Potentiometer Styles G43B Gull-Wing, Top Adjust,000,000,000,000,000, G43BT B M G43BT B M G43BT B M G43BT B 1 M G43BT B 1 M G43BT B 1 M G43BT B 2 M G43BT B 2 M G43BT B 2 M G43BT B 3 M G43BT B 3 M G43BT B 3 M G43BT B 4 M G43BT B 4 M G43BT B 4 M G43B B M G43B B M G43B B M G43B B 1 M G43B B 1 M G43B B 1 M G43B B 2 M G43B B 2 M G43B B 2 M G43B B 3 M G43B B 3 M G43B B 3 M G43B B 4 M G43B B 4 M G43B B 4 M 5 G43BT B 5 M G43B B 5 M 5 G43BT B 5 M G43B B 5 M G43B G43E Reverse Markings, Gull-Wing, Top Adjust,000,000,000,000,000, G43ET B M G43ET B M G43ET B M G43ET B 1 M G43ET B 1 M G43ET B 1 M G43ET B 2 M G43ET B 2 M G43ET B 2 M G43ET B 3 M G43ET B 3 M G43ET B 3 M G43ET B 4 M G43ET B 4 M G43ET B 4 M G43E B M G43E B M G43E B M G43E B 1 M G43E B 1 M G43E B 1 M G43E B 2 M G43E B 2 M G43E B 2 M G43E B 3 M G43E B 3 M G43E B 3 M G43E B 4 M G43E B 4 M G43E B 4 M 5 G43ET B 5 M G43E B 5 M 5 G43ET B 5 M G43E B 5 M G43E G43SA J-Hook, Side Adjust,000,000,000,000,000, G43SAT1 B M G43SAT1 B M G43SAT1 B M G43SAT1 B 1 M G43SAT1 B 1 M G43SAT1 B 1 M G43SAT1 B 2 M G43SAT1 B 2 M G43SAT1 B 2 M G43SAT1 B 3 M G43SAT1 B 3 M G43SAT1 B 3 M G43SAT1 B 4 M G43SAT1 B 4 M G43SAT1 B 4 M G43SA B M G43SA B M G43SA B M G43SA B 1 M G43SA B 1 M G43SA B 1 M G43SA B 2 M G43SA B 2 M G43SA B 2 M G43SA B 3 M G43SA B 3 M G43SA B 3 M G43SA B 4 M G43SA B 4 M G43SA B 4 M 5 G43SAT1 B 5 M G43SA B 5 M 5 G43SAT1 B 5 M G43SA B 5 M G43SA 7/8
8 Nominal Resistance Value (Ω) Code Part Numbers Resistance Tolerance % Tape & Reel Bulk Effective Date April 5 Potentiometer Styles G43BF Gull-Wing, Bottom Adjust,000,000,000,000,000, G43BF B M G43BF B M G43BF B M G43BF B 1 M G43BF B 1 M G43BF B 1 M G43BF B 2 M G43BF B 2 M G43BF B 2 M G43BF B 3 M G43BF B 3 M G43BF B 3 M G43BF B 4 M G43BF B 4 M G43BF B 4 M G43BF B 5 M G43BF B 5 M G43BF Packaging Standard: Tape & Reel Packaging Bulk Packaging G43AT, G43DT, G43BT, G43ET All G43 Models pieces per 7 reel. pieces per vinyl bag. G43SAT1 7 pieces per reel. pieces per box. Cleaning Guidelines For cleaning and other information, refer to Guidelines and Precautions for Using Potentiometers. 8/8
1/4 Square, Single-Turn, Through-Hole Sealed Cermet Trimmers. Environmental
with Knob TOCOS POTENTIOMETERS 1/4 Square, Single-Turn, Through-Hole Sealed Cermet Trimmers Features 1/4 square, single-turn, through-hole, sealed cermet trimmers Top and side adjust styles available Knob
More informationSINGLE TURN COPAL ELECTRONICS S T T A Ω ( 1 2 ) FEATURES PART NUMBER DESIGNATION
SINGLE TURN INTERNAL STRUCTURE 7 6 5 4 9 8 FEATURES Lead-free soldering, Cadmium-free Top and side adjustment styles Rotor with a cross slot for ease of adjustment Leaded terminals provide strong as adhesive
More informationCMS SLIDE SWITCHES (SMD) FEATURES PART NUMBER DESIGNATION CMS T B. Please refer to the LIST OF PART NUMBERS when placing orders.
SLIDE SWITHES (SMD) MS RoHS compliant INTERNAL STRUTURE FEATURES Part name over Slider Housing Slider contact Fixed contact Material Steel (SP), Tin-plated Polyamide opper alloy, Gold-plated Flammability
More informationCMS SLIDE SWITCHES (SMD) COPAL ELECTRONICS CMS T B FEATURES PART NUMBER DESIGNATION. RoHS compliant INTERNAL STRUCTURE.
OPAL ELETRONIS SLIDE SWITHES (SMD) MS RoHS compliant INTERNAL STRUTURE 7 FEATURES RoHS compliant Excellent contact stability by twin Gold-plated contact mechanism Load life of, cycles ompatible with automatic
More informationSERIES WW24 Industrial Wirewound Rotary Potentiometer 24mm Diameter / 5 Watts
SERIES WW4 Industrial wound Rotary Potentiometer 4mm Diameter / 5 Watts For more information about this product, visit our website at: www.potentiometers.com 5 watt @ 5 C / 4 watt @ 55 C power rating Dust-proof
More informationSA-7000 ROTARY CODED SWITCHES (SMD) S A T A FEATURES PART NUMBER DESIGNATION COPAL ELECTRONICS. RoHS compliant. 1 Marking cover 2 3 4
OPL ELETRONIS ROTRY ODED SWITHES (SMD) S- RoHS compliant INTERNL STRUTURE Part name Material Flammability FETURES RoHS compliant Low profile of. mm Wide variety (top or side setting, or positions, J-hook,
More informationLeaded Surface Mount Series 767 Technical Data
Leaded Surface Mount Series 767 Technical Data Features Medium Body Design Solid Ceramic Construction No Internal Dendrite Growth Requires 30% Less Board Space Than Molded Products of the Same Power Rating
More informationFully Sealed Container Cermet Potentiometers Military and Professional Grade
PE0 Fully Sealed Container Cermet Potentiometers FEATURES Watt at 70 C High power rating Low temperature coefficient Excellent stability Full sealing Low contact resistance variation Mechanical strength
More informationFlammability FEATURES. Cover. Slider C S S T B
OPAL ELETRONIS OMPAT SLIDE SWITHES SS RoHS compliant INTERNAL STRUTURE Part name Material Flammability FEATURES Low-profile of mm Self-return type available RoHS compliant over Slider Housing Stainless
More informationTactile Switch. Ordering Information. A Wide Range of Models: 6 6 mm, mm, Side-operated, High-force, and Gold-plated.
Tactile Switch BF A Wide Range of Models: mm, mm, Side-operated, High-force, and Gold-plated. Extended mechanical/electrical durability: 0 x 0 operations for x mm type and x 0 operations for the x mm type
More informationModel 97 & 99-5/8 Square Single-Turn Panel Control with Rotary Switch
*RoHS COMPLIANT Features Virtually infinite electrical circuit isolation Metal or plastic shaft options DPST and DPDT switch options RoHS compliant* Model 97 & 99-5/8 Square Single-Turn Panel Control with
More information6mm. potentiometer SMD PS-6 & PSX-6 MAIN FEATURES MECHANICAL SPECIFICATIONS ELECTRICAL SPECIFICATIONS HOW TO ORDER.
6mm potentiometer SMD MECHNICL SPECIFICTIONS Stop torque: > Ncm. ( >7 in-oz) PS-6 & PSX-6 MIN FETURES Specifically designed for leadfree reflow soldering processes (excellent performance). Carbon resistive
More informationEncoder. Switches. Series Size SMD
Piher is recognised as a world leader in custom controls and sensor solutions by the top Land Vehicle/Automotive and Appliance players. In this catalogue you will find a selection of the most prolific
More informationResistance WIREWOUND. Wiper Travel. STANDARD RESISTANCE VALUES (in Ω) (1) 20, 50, 100, 200, 500, 1K, 2K, 5K
Bulk Metal Foil Technology Ultra High Precision Trimming Potentiometers, QPL Approved 1 / 4 " Square, Qualified to MIL-PRF-22097, Char. F, RJ26 with a Smooth and Unidirectional Output INTRODUCTION Vishay
More informationType CPF Series. Thin Film Precision Resistors. Key Features
Type CPF Series Key Features Thin film precision resistors with TC's to 15ppm and tolerances to 0.05%. Wide range of case sizes from 0201 to 2512 Suitable for all applications where close accuracy and
More informationCR0603/CR0805/CR Chip Resistors
*RoHS COMPLIANT Features RoHS compliant* Power rating at 7 C: CR63 -.1 W, CR85 -.125 W, CR126 -.25 W Tight tolerances of bottom electrode width Suitable for all types of soldering processes Three layer
More informationChip Resistors / Chip Arrays
Chip Resistors / Chip Arrays w w w. b o u r n s. c o m I. CR Series Chip Resistors...92 II. CAT/CAY Series Chip Resistor Arrays...96 CAT/CAY 16 Series...96 CAY1 Chip Resistor Array...97 CAY17 Bussed Resistor
More information6x6 mm Thinner Type Tactile Switches (Pitch 4.5 mm) ACTUATOR COLOR & OPERATING FORCE: Black, 100gf Brown, 160gf Red, 260gf
TP6GM... TP6GMB... 2.5 TP6M... General Tolerance ±0.2mm How to order: TP6 1 2 3 5 6 7 1 GROUND TERMINAL: Blank Without Ground Terminal G With Ground Terminal 5 A K C ACTUATOR COLOR & OPERATING FORCE: Black,
More informationMIL-PRF-39035, Char. H with a Smooth and Unidirectional Output
Bulk Metal Foil Technology Ultra High Precision Trimming Potentiometers, / 4 " Square, RJ26 Style, Designed to Meet or Exceed The Requirements of MIL-PRF-905, Char. H with a Smooth and Unidirectional Output
More informationResistance WIREWOUND. Wiper Travel. STANDARD RESISTANCE VALUES (in Ω) (1) 20, 50, 100, 200, 500, 1K, 2K, 5K
Bulk Metal Foil Technology Ultra High Precision Trimming Potentiometers, QPL Approved / 4 " Square, Qualified to MIL-PRF-22097, Char. F, RJ26 with a Smooth and Unidirectional Output INTRODUCTION Vishay
More informationDistributed by: www.jameco.com 1-8-831-4242 The content and copyrights of the attached material are the property of its owner. *RoHS COMPLIANT VERSIONS AVAILABLE Features Lead free version available (see
More informationS-1000A/2000A ROTARY CODED SWITCHES S A W FEATURES PART NUMBER DESIGNATION. Please refer to the LIST OF PART NUMBERS when placing orders.
ROTARY ODED SWITHES S-A/A RoHS compliant INTERNAL STRUTURE S-A / A series FEATURES Part name Housing ontact Terminal pin Base O ring Material Polybutyleneterephthalate opper alloy, Gold-plated Polybutyleneterephthalate
More informationThin Film Ultra Precision Resistors
Type RU73 Series Key Features High precision - TCR 2ppm/ C and 3ppm/ C Tolerance down to 0.01% Thin film (nichrome) Available in standard and high power versions Terminal finish electroplated 100% matte
More informationData Sheet. Chun Ann J.C Liu. Customer: Thin Film Precision Chip Resistor - AR Series. Checked. Product :
Data Sheet Customer: Product : Thin Film Precision Chip Resistor - AR Series Size: 0201/0402/0603/0805/1206/1210/2010/2512 Issued Date: 19-Aug-10 Edition : REV.C6 Produced by Checked Approved by Prepared
More informationThin Film Current Sensing Chip Resistor (TCS Series)
(TCS Series) Features -Thin film process -High power rating up to 3 Watts in 2512 size -Tight tolerance down to ±0.5% -Extremely low TCR down to PPM/ C -Resistance values from 50m to 1ohm -High purity
More informationPLEDxUSW Series, Unidirectional, White DO-214AA
PLEDxUSW Unidirectional Series PLEDxUSW Series, Unidirectional, White DO-214AA RoHS Description Agency Approvals Agency Agency File Number E133083 The PLEDxUSW open LED protectors provide an electronic
More informationPLEDxUSWxA Series - Unidirectional, White Body
PLEDxUSWxA Series - Unidirectional, White Body RoHS e3 Description Agency Approvals Agency Agency File Number E133083 PLEDxUSWxA open LED protectors provide a switching electronic shunt path when an LED
More informationFully Sealed Container Cermet Potentiometers Submarine Applications
Fully Sealed Container Cermet Potentiometers Submarine Applications FEATURES High power rating 1.5 W at 70 C Stainless steel shaft and bushing to endure sea salt water immersion Fully sealed IP68 on panel
More informationType RN73 Series. Thin Film Precision Resistors. Electrical Characteristics. Key Features. Applications
Type RN73 Series Key Features High precision - TCR 5ppm/ C and 10ppm/ C Tolerance down to 0.01% Thin film (nichrome) Terminal finish electroplated 100% matte Sn Applications Communications Industrial Controls
More informationMetal Foil Low Resistance Chip Resistor MFF Series
Page No. 1/8 Metal Foil Low Resistance Chip Resistor MFF Series Application Features Entertainment Low Resistance / TCR / EMF/Inductance Power supply Excellent long term stability Measuring instrument
More informationLow Resistance Flat Chip Resistors Type SR73
Low Resistance Flat Chip Resistors Type SR73 1. Scope This specification applies to chip resistors (SR73) produced by KOA Corporation. CERTIFIED AHA 9/29/11 CERTIFIED 2. Type Designation The type designation
More informationLR Series. Construction. Application. Features
Metal Alloy Low-Resistance Resistor LR Series Construction Application Power supply Battery pack DIY tools Inverter/Converter (AC/DC, DC/DC, DC/AC) Measurable instrument Consumer electronics Note book
More informationB3F. Miniature, Space-saving Switch
B3F Miniature, Space-saving Switch Long mechanical / electrical service life Ideal for applications such as audio, office and communications equipment, TVs, etc Taped radial, vertical, high-force, and
More informationFully Sealed Container Cermet Potentiometer Professional Grade
Fully Sealed Container Cermet Potentiometer Professional Grade T Q O QUICK REFERENCE DATA Multiple module Switch module Detent module Special electrical laws No n/a n/a A: linear, L: logarithmic, F: reverse
More information10mm. potentiometer SMD PS-10 & PSX-10 MAIN FEATURES MECHANICAL SPECIFICATIONS ELECTRICAL SPECIFICATIONS HOW TO ORDER.
10mm potentiometer SMD MECHNIC SPECIFICTIONS Mechanical rotation angle: 35 ± 5 Electrical rotation angle: 0 ± 0 Torque: 0.4 to Ncm. (0.6 to.7 in-oz) Stop torque: > 5 Ncm. ( >7 in-oz) ife*: Up to 10K cycles
More informationSRM VDE. REG.-Nr. E932. Cap Diameter (D1, mm) Body Diameter (D2, mm)
D2 VDE REG.-Nr. E932 Specifications Per IEC 605- Features B L D IEC60065 & UL676 Compliant MELF packaging yet capable of high power handling Special conductive film enhances anti-surge capability. Absorbs
More information3/4" Rectangular (19 mm) Multi-Turn Cermet Trimmer
3/4" Rectangular (19 mm) Multi-Turn Cermet Trimmer 43 FEATURES W at 70 C Wide ohmic value range (10 Ω to 5 MΩ) Panel mount available Multi-finger wiper for better C.R.V. Tests according to CECC 41000 or
More informationThick Film Chip Array Resistor
Date From Dec.. 2004 INTRODUCTION Chip array resistors are general passive component which is useful for derating voltage, current controlling in circuit and surface mounting is available. Samsung electro-mechanics
More informationMetal Film MELF Resistors
FEATURES SURFACE MOUNT IN SIZES 0102 (0805), 0204 (1406) AND 0207 (2410) HIGH RELIABILITY AEC-Q200 QUALIFIED (see part numbering system for details) THIN FILM CONSTRUCTION AVAILABLE IN PRECISION TOLERANCE
More informationChip Array Resistor INTRODUCTION FEATURE AND APPLICATION. Feature. Application
INTRODUCTION Chip array resistors are general passive component which is useful for derating voltage, current controlling in circuit and surface mounting is available. Samsung electro-mechanics manufactures
More informationCompact Flat Size Relay for Automotive. (Unit: mm inch)
Compact Flat Size Relay for Automotive CP RELAYS Sealed 13.1.1 9..374 13.1.1 1..413 FEATURES Compact flat type PC board terminal type: 9. mm.374 inch Compact and High
More informationKnob Potentiometer FEATURES. 12 wrench CIRCUIT DIAGRAM (1) (3) (2)
FEATURES 1 Watt at 40 C Test according to CECC 41300 - version for professional and industrial applications PA16 - version for professional audio applications Compact (integrated) Minimum clearance required
More informationA S J ASJ PTE LTD LEAD FREE THIN FILM CHIP RESISTOR SPECIFICATION. Reference No. : SYS-ENG-209. Revision No. : D
ASJ PTE LTD LEAD FREE THIN FILM CHIP Reference No. : SYS-ENG-209 Revision No. : D DOC NO: SYS-ENG-209 PAGE: 2 of 24 1.0 SCOPE...... 3 2.0 PART NUMBERING SYSTEM...... 3 3.0 RATING....... 3 3.1 Rated Power......
More information12.5 mm Modular Panel Potentiometer High Dielectric Strength
12.5 mm Modular Panel Potentiometer High Dielectric Strength QUICK REFERENCE DATA Multiple module Up to 7 modules Switch module Yes Detent module Yes Special electrical laws A: linear, L: logarithmic,
More informationPTS Series High Grade Slide Potentiometer
*RoHS COMPLIANT Features High grade, long life Single and dual gang Assortment of resistance tapers Tracking error within ±3 db 45, 60 and 100 mm sizes Wide operating temperature range T-bar lever option
More informationSelection Series: E24 & E96 E24 & E96 Temp. Coefficient (ppm/ C):
Thin Film Precision Resistors 1206 1210 Rated Power @ 70 C: 0.125W 0.2W Resistance Range (Ohms) Min: 4R7 4R7 4R7 1R0 4R7 1R0 4R7 4R7 4R7 1R0 4R7 1R0 Max: 1M0 2M5 1M0 2M5 1M0 2M5 1M0 2M5 1M0 2M5 1M0 2M5
More informationFully Sealed Container Cermet Potentiometers Submarine Applications
FEATURES High power rating W at 70 C Stainless steel shaft and bushing to endure sea salt water immersion Fully sealed IP68 on panel Tight temperature coefficient (± 75 ppm/ C typical) Compliant to RoHS
More informationPLED Unidirectional Series (PLEDxUx)
(PLEDxUx) PLED Open LED Protectors Agency Approvals Agency Agency File Number E133083 Description The (PLEDxUx Series) open LED protectors provide an electronic switching shunt path around a single LED
More informationThin Film Precision Chip Resistor (AR Series)
Construction D1 L (AR Series) Features -Advanced thin film technology -Very tight tolerance down to ±0.01% -Extremely low TCR down to PPM/ C -Wide resistance range 1ohm ~ 3Mega ohm -Miniature size 0201
More informationYAGEO CORPORATION SMD RESISTORS. RC Series FEATURES. Extremely Thin and Light. Highly Reliable Multilayer Electrode Construction
YAGEO CORPORATION SMD RESISTORS Thick Film Chip Resistors RC Series FEATURES Extremely Thin and Light Highly Reliable Multilayer Electrode Construction Compatible with all Soldering Process Highly Stable
More informationLong Life Cermet Potentiometer 2 Million Cycles
Long Life Cermet Potentiometer 2 Million Cycles FEATURES 2 million cycles Cermet element 12.5 mm square single turn panel control 4, 6 and 6.35 shaft diameters and 29 terminal styles Multiple assemblies
More informationFully Sealed Container 12 mm Square or Round Single-Turn Cermet Trimmer
Fully Sealed Container 12 mm Square or Round Single-Turn Cermet Trimmer The trimming potentiometers T12 and T13 fully meet the requirements of CECC 41 100. The use of a cermet track combined with sealing
More informationModel BD3238N5050AHF. Ultra Low Profile 0404 Balun
Model BD338N55AHF Ultra Low Profile 44 Balun 5Ω to 5Ω Balanced Description The BD338N55AHF is a low cost, low profile sub-miniature unbalanced to balanced transformer designed for differential inputs and
More informationChip Trimmer Potentiometer
A general purpose, compact, and low-profile type that is suitable for a wide range of applications. Car Use Features Conforms to JIS C 0806- (Packaging of surface mount components on continuous tapes).
More information50W TO220 High Power Resistors
50W TO220 High Power Resistors MHP 50 Non-inductive, thin film technology. Thermally enhanced Industry standard TO220 package. RoHS compliant. Low thermal resistance, 2.3 C/W resistor hot spot to metal
More informationTeccor brand Thyristors High Energy Bidirectional SIDACs
Kxxx0yH Series RoHS Description The new Kxxx0yH is a higher energy SIDAC switch for gas ignition applications requiring higher current pulse current especially at low repetition rate. It is offered in
More informationCS14. Carbon Endless Sensor. Specifications on this catalog are for reference only, as they are subject to change without notice.
Carbon Endless Sensor 5 www.acptechnologies.com Specifications on this catalog are for reference only, as they are subject to change without notice. mm rotary position sensor with 30º mechanical rotation
More informationINPAQ. Specification. WIP201610S L Series. Product Name. Power Inductor. Global RF/Component Solutions
WIP201610S L Series Specification Product Name Series Power Inductor WIP201610S L Series Size EIAJ 2016 WIP201610S L Series Engineering Specification 1. Scope Feature High saturation current realized by
More informationPrecision Thin Film Precision Resistors
Key Features Thin film precision resistors with TC's of 15ppm, 25ppm and 50ppm and tolerances to 0.1%. Applications in measurement, telemetry and for sensing circuits. Case sizes 0402, 0603, 0805, 1206,
More informationSurface-mounting Relay
Surface-mounting Relay Extremely Thin SPST-NO Flat Relay, One of the Thinnest Relays in the World Dimensions of 7.(W).6(L) 4.2 mm(h) (SMD) or 3.8 mm(h) (TH) represent a reduction of approximately 2% in
More informationThin Film Precision Chip Resistor (AR Series)
Features Advanced thin film technology Very tight tolerance down to ±0.01% Extremely low down to ±5PPM/C Wide resistance range 1ohm ~ 3Mega ohm Miniature size 0201 available Thin Film Precision Chip Resistor
More informationFrelTec GmbH. Thin Film Chip Resistor SMD High Precision (1% to 0,01%) Low TCR (2 to 50 ppm) and Thin Film current sensing
GmbH Mathildenstr. 0A 89 Starnberg Germany Thin Film Chip Resistor SMD High Precision (% to 0,0%) Low TCR ( to 50 ppm) and Thin Film current sensing 5/7/05 / GmbH www.freltec.com SPECIFICATION Part Number
More informationTel: /Fax: , Kuanfu N Road, HsinChu Industrial Park, 303 Taiwan, ROC 1
70, Kuanfu N Road, HsinChu Industrial Park, 303 Taiwan, ROC 1 Thin Film Precision Chip Resistors (AR Series) 1. Scope This specification applies to all sizes of rectangular-type fixed chip resistors with
More informationElectrical Specifications. Insertion to +85 TOP VIEW SIDE VIEW BOTTOM VIEW. Pin 2. Yantel Corporation
Description The is a low profile, high performance 20dB directional coupler. It is designed for DCS & PCS applications. This component is suitable for feed-forward amplifier and signal sampling circuits
More informationSMD High Power Precision Resistors. Type RP73 Series
Type RP73 Series Key Features High precision - Tolerance down to 0.05% and TCR down to 5PPM Power rating to 1.0W Up to 200V DC operating Terminal finish electroplated 100% matte Sn Applications Communications
More informationMELF Coated Thin Film Precision Resistors (MELFC Series)
Features: Precision TCR of 0, 5, 25 & 50ppm/ C High reliability and stability of ±0. and ±0.5% Excellent pulse load capability Strong mechanical body due to cylindrical shape AEC-Q200 compliant RoHS and
More informationFully Sealed Potentiometer Professional Grade
Fully Sealed Potentiometer Professional Grade PE0 QUICK REFERENCE DATA Multiple module No Switch module n/a Detent module Yes Special electrical laws A: linear, L:, F: reverse Sealing level IP 67 Lifespan
More informationFeatures. Symbol Parameters Test Conditions Min Max Unit V T. TA=25 C Pulse Wave = 10μs, Sine Wave, f=120hz K2201GL 230 V BO K2401GL K2401GL
Standard Bidirectional SIDACs Kxxx1GL Series RoHS Description Schematic Symbol The Multipulse SIDAC is a voltage switch used in Metal- Halide lamp ignition circuits, as well as High Pressure Sodium lamp
More informationPCB Footprint Max.Load Coil Voltage Non-Latching part number Single-coil latching part number Standard ground terminal (1GHz)
High Frequency Relay G6K-RF Surface Mount, 1GHz / 3 GHz Miniature DPDT, High Frequency Relay New Models with 3 GHz band available ( -T versions) Space-saving 1 GHz version with smaller ground terminal
More informationModel 2425B50-50C Rev. A
rit Model 2425B50-50C Xinger Balun 50Ω to 100Ω Balanced Description The 2425B50-50C is a low profile sub-miniature balanced to unbalanced transformer designed for differential inputs and output locations
More informationVersion: 1.2 Document code:ma2512 Effective date : Page: 1 of 7. Metal Alloy shunt resistor MA2512 series ROHS
Document code: Page: 1 of 7 Metal Alloy shunt resistor series ROHS Metal Alloy Shunt Resistor Specification Document code: Page: 2 of 7 Metal Alloy shunt resistor series ROHS Scope This specification applies
More informationSMD High Power Precision Resistors. Type RP73 Series
Key Features High precision - Tolerance down to 0.05% and TCR down to 5PPM Power rating to 1.0W Up to 200V DC operating Terminal finish electroplated 100% matte Sn Applications Communications Industrial
More informationMessrs:Digikey. Preliminary Specifications. Drawing No. Issued Date. Note: Part Number will be revised in case of specification change.
Preliminary Specifications Issued Date. Nov,14,2018 Messrs:Digikey Note: Part Number will be revised in case of specification change. Product Type Series Frequency Quartz Crystal CX2016DB 48000kHz Customer
More informationPLEDxN Series. PLED Open LED Protectors PLEDxN Series. RoHS. Description
RoHS Description The open LED protector provides a switching electronic shunt path when a single LED in an LED string fails as an open circuit. This ensures the entire LED string will continue to function
More informationLEAD FREE CHIP RESISTOR SPECIFICATION
ASJ PTE LTD LEAD FREE CHIP RESISTOR Reference No. : SYS-ENG-205 Revision No. : Z DOC NO: SYS-ENG-205 PAGE: 2 of 40 1.0 SCOPE..... 3 2.0 PART NUMBERING SYSTEM.... 3 3.0 RATING..... 3 3.1 Rating Power....
More informationSpecifications. Drawing No. USY1M-H / 11 Issued Date.
Specifications Drawing No. USY1M-H1-16426-00 1 / 11 Issued Date. Messrs: KED USA Note: Part Number will be revised in case of specification change. Apr,20,2016 Product Type Quartz Crystal Series CX2016DB
More informationDISCONTINUED (2008) 4 Pole (2 FORM C+ 2 FORM A) Signal Relay for Central Switching/ Data Transmission FTR-B2 SERIES. RoHS compliant FEATURES
4 Pole ( FORM C+ FORM A) Signal Relay for Central Switching/ Data Transmission FTR-B SERIES RoHS compliant FEATURES DISCONTINUED (8) 4 POLE MINIATURE RELAY Mounting space of 17mm with 4 pole relay, suitable
More informationSpecifications. Customer Part Number - Customer Specification Number -
Specifications TO: KED USA Drawing No. UKY1C-H1-14E53-00[37] 1/11 Issued Date. Dec,26,2014 Note:Part Number will be revised in case of specification change. Product Type Quartz Crystal Series CX2016DB
More informationKnob Potentiometer with Switch
Knob Potentiometer with Switch, The is a revolutionary concept in panel mounted potentiometers. This unique design consists of a knob driving and incorporating a cermet potentiometer. Only the mounting
More informationWIRE WOUND CHIP INDUCTORS HCI SERIES HCI 0805 F T 1R0 K - Introductions. Features. Part Number Code HCI SERIES
HCI SERIES WIRE WOUND CHIP INDUCTORS HCI SERIES Introductions Product : HCI Miniature SMD Inductor For Power Line Size : 0805 The HCI series are low profile inductor used in notebooks, PC s, Cellular phone
More informationMINIATURE RELAY 2 POLES, 2A HIGH INSULATION/WIDE GAP FTR-C1 Series
MINIATURE RELAY 2 POLES, 2A HIGH INSULATION/WIDE GAP FTR-C1 Series RoHS compliant Features 2 Poles, 2 form C Contact gap: more than 0.6mm High surge voltage: 2,00V between open contacts,000v between coil
More informationULTRA LOW POWER SMD METAL STRIP RESISTORS
Features These specification covers 2512 sized high power low resistance current sensing metal resistors. PART NUMBERING SYSTEM: - 2512 A 1W R005 F E C Type Dimensions Code 2512 Construction Resistance
More informationSpecifications. Customer Part Number - Customer Specification Number - KYOCERA Part Number
Specifications Drawing No. UKY1C-H1-14560-00[40] 1/11 Issued Date. MAY.16,2014 TO: Digi-Key Note:In case of specification change, KYOCERA Part Number also will be changed. Product Name Quartz Crystal Product
More informationChip Resistor INTRODUCTION FEATURE AND APPLICATION. Feature. Application
INTRODUCTION Chip resistors are general passive component which is useful for derating voltage, current controlling in circuit and surface mounting is available. Samsung electro mechanics also manufactures
More informationSPECIFICATIONS. Metal Film Precision Resistor. CSRV-Serie SWISSDIS. Swissdis AG Grasweg 7 CH-4911 Schwarzhäusern
SWISSDIS Swissdis AG Grasweg 7 CH-4911 Schwarzhäusern Tel.: +41 62 919 44 00 Fax: +41 62 919 44 01 info@swissdis.ch www.swissdis.ch SPECIFICATIONS Metal Film Precision Resistor CSRV-Serie Version August
More informationPART NUMBER: ACTR MHz-DCC6C-75kHz-v1.1 Frequency: MHz
PART NUMBER: ACTR3028-315MHz-DCC6C-75kHz-v1.1 Frequency: 315.000MHz Features 1-port Resonator Provides reliable, fundamental mode, quartz Frequency stabilization i.e. in transmitters or local oscillators
More informationThick Film Chip Resistors Product Specification
1/21 1 Scope This specification is applicable to lead and halogen free RTT series thick film chip resistors. 2 Explanation Of Part Numbers (EX) RTT 03 101 J TP Type Nominal Resistance Resistance Size Tolerance
More informationMINIATURE RELAY 1 POLE 1 to 2 A (FOR SIGNAL SWITCHING) FBR211 SERIES
MINIATURE RELAY POLE to 2 A (FOR SIGNAL SWITCHING) RoHS compliant FEATURES 2 A maximum carrying current Capable of 2 A maximum continuous carrying current in the contact Superior reliability gold-overlay
More informationModel B0922N7575AHF Rev B. Ultra Low Profile 0404 Balun
Model B9N7575AHF Ultra Low Profile 44 Balun 75Ω to 75Ω Balanced Description The B9N7575AHF is a low profile, low impedance mm square subminiature wideband unbalanced to balanced transformer designed for
More informationReturn loss (db) Insertion loss (db) .56±.06 TBD. GND / DC Feed 1 + RF GND 2. Unbalanced Port Balanced Port Balanced Port.
Model BD6N5AHF Ultra Low Profile 44 Balun 5Ω to Ω Balanced Description The BD6N5AHF is a low cost, low profile sub-miniature unbalanced to balanced transformer designed for differential inputs and output
More informationQTCT570 SERIES 5 x 7mm MINIATURE SMD TEMPERATURE CONTROLLED CRYSTAL OSCILLATORS 2.8 to 3.3Vdc MHz to MHz Description
Description Q-Tech s surface-mount QTCT570 oscillators consist of an IC 2.8Vdc, 3.3Vdc clock TCXO built in a low profile ceramic package with gold plated contact pads. Features ECCN: EAR99 Frequency range
More informationTrimmer Potentiometers
!Note R50E1.pdf 0.9.5 Trimmer Potentiometers SMD Open Type 3mm Size PVZ3/PVS3/PVA3 Series PVZ3 Series Features 1. Excellent solderability characteristics are achieved via special plating techniques on
More informationHVR. Lead Wire Length (H, mm)
High Resistor Features Special conductive film withstands high voltage d L H D working voltage far over that of generalpurpose resistors Suitable for applications such as TV s, high voltage power supply,
More informationSamples. Symbol Parameter Test Conditions Value Unit RMS on-state current T C = 100 C 40 A I T(AV) Average on-state current T C
Sxx40x Series RoHS Description Excellent unidirectional switches for phase control applications such as heating and motor speed controls. Standard phase control SCRs are triggered with few milliamperes
More informationEncoders and switches
Encoders and switches Encoders and switches v02 Navarra de Componentes Electrónicos, S.A. Polígono Industrial Municipal Vial T2 Nº22 31500 Tudela Navarra Spain Tel: +34 948 820450 Fax: +34 948 824050 www.meggitt.com
More informationQTCT350 SERIES 3.2 x 5mm MINIATURE SMD TEMPERATURE CONTROLLED CRYSTAL OSCILLATORS 2.8 to 5.0Vdc MHz to 52.
Description Q-Tech s surface-mount QTCT350 oscillators consist of an IC 3.3Vdc, 5.0Vdc TCXO built in a low profile ceramic package with gold plated contact pads. Features ECCN: EAR99 Frequency range from
More informationThis specification applies for the RMS series of Anti-Sulfurated thick film chip resistors made by TA-I. RMS 10 J T 103.
page number 1/13 1. Scope : This specification applies for the RMS series of Anti-Sulfurated thick film chip resistors made by TA-I. 2. Construction: Over Coat (Color : Black) Conductor Sn Plating Ceramic
More informationFully Sealed Potentiometer Military and Professional Grade
PE0 Fully Sealed Potentiometer Military and Professional Grade DIMENSIONS in millimeters (inches) ± 0.5 mm (± 0.02") FEATURES High power rating W at 70 C Low temperature coefficient (150 ppm/ C typical)
More informationRMC10,16,20,32,35,50,63 Automotive Grade Page: 1/10
+5 C +35 C 75% Product specification contained in this data sheet are subject to change at any time without notice If you have any questions or a Purchasing Specification for any quality Agreement is necessary,
More informationTactile Switch. Ordering Information. A Wide Range of Models: 6 x 6 mm, 12 x 12 mm, Vertical, and High-force.
Tactile Switch A Wide Range of Models: 6 x 6 mm, 12 x 12 mm, Vertical, and High-force. A positive click action plus a long life equal to that of a no-contact switch. Radial models (taping specifications)
More information