Aluminum Electrolytic Capacitors Radial Low Profile, 5 mm

Transcription

1 Aluminum Electrolytic Capacitors Radial Low Profile, 5 mm 038 RSU 097 RLP 7 higher CV-values 5 mm ig. 1 longer life SMD 153 CRV QUICK REERENCE DATA DESCRIPTION VALUE Nominal case sizes (Ø D x L in mm) 4 x 5 to 6.3 x 5 Rated capacitance range, C R 1.0 μ to 100 μ Tolerance on C R ± 20 % Rated voltage range, U R 6.3 V to 50 V Category temperature range -40 C to +85 C Endurance test at 85 C 1000 h Useful life at 85 C 1500 h Useful life at 40 C, 1.4 x I R applied h Shelf life at 0 V, 85 C 500 h Based on sectional specification IEC / EN Climatic category IEC / 085 / 56 EATURES Useful life: 1500 h at 85 C Very low profile, 5 mm height Extremely miniaturized Polarized aluminum electrolytic capacitors, non-solid electrolyte Radial leads, cylindrical aluminum case, insulated with a blue sleeve Charge and discharge proof Material categorization: for definitions of compliance please see APPLICATIONS General purpose, industrial, automotive and audio-video Coupling, decoupling, smoothing, filtering and timing High mounting density Portable and mobile equipment (very small size and very low mass), low profile equipment MARKING The capacitors are marked (where possible) with the following information: Rated capacitance (in μ) Rated voltage (in V) Negative terminal identification Code indicating factory of origin Name of manufacturer Date code, in accordance with IEC Series number (134) SELECTION CHART OR C R, U R, AND RELEVANT NOMINAL CASE SIZES (Ø D x L in mm) C R U R (V) (μ) x x x x 5 5 x x 5-5 x x x 5-5 x x x x x x x Revision: 14-eb-17 1 Document Number: 28307

2 DIMENSIONS in millimeters AND AVAILABLE S Ø D L + - ± min Ø d 5 min ig. 2 - orm CA: Long leads Case Ø D = 4 mm to 6.3 mm; pitch = 5 mm ig. 3 - orm TA: Taped in box (ammopack) Pitch = 2.5 mm Case Ø D = 4 mm to 6.3 mm ig. 4 - orm TNA: Taped in box (ammopack) Table 1 DIMENSIONS in millimeters AND PACKAGING QUANTITIES NOMINAL CASE SIZE Ø D x L CASE CODE Ø d Ø D max. L max. CA PACKAGING QUANTITIES TA TNA 4 x ± x ± x ± or detailed tape dimensions please see Revision: 14-eb-17 2 Document Number: 28307

3 ELECTRICAL DATA SYMBOL DESCRIPTION C R Rated capacitance at, tolerance ± 20 % I R Rated RMS ripple current at, 85 C I L2 Max. leakage current after 2 min at U R tan Max. dissipation factor at Z Max. impedance at 100 khz Unless otherwise specified, all electrical values in Table 2 apply at T amb = 20 C, P = 86 kpa to 106 kpa, RH = 45 % to 75 % ORDERING EXAMPLE Electrolytic capacitor 134 series 22 μ / 16 V; ± 20 % Nominal case size: Ø 5 mm x 5 mm; form TA Ordering code: MAL E3 ormer 12NC: Table 2 ELECTRICAL DATA AND ORDERING INATION U R (V) C R (μ) NOMINAL CASE SIZE Ø D x L I R 85 C (ma) I L2 2 min (μa) tan Z 100 khz () BULK LONG LEADS CA ORDERING CODE MAL TAPED AMMOPACK 22 4 x E E E x E E E x E E E x E E E x E E E x E E E x E E E x E E E x E E E x E E E x E E E x E E E x E E E x E E E x E E E x E E E3 2.5 TA TNA ADDITIONAL ELECTRICAL DATA PARAMETER CONDITIONS VALUE Voltage Surge voltage U s 1.15 x U R Reverse voltage U rev 1 V Current Leakage current After 2 min at U R I L C R x U R or 3 μa (whichever is greater) Resistance Equivalent series resistance (ESR) Calculated from tan max. and C R (see Table 2) ESR = tan /2 f C R RIPPLE CURRENT AND USEUL LIE Table 3 ENDURANCE TEST DURATION AND USEUL LIE ENDURANCE AT 85 C (h) USEUL LIE AT 85 C (h) Multiplier of useful life code: CCC205 Revision: 14-eb-17 3 Document Number: 28307

4 3.3 CCC205 I A I R Lifetime multiplier I A = Actual ripple current at I R = Rated ripple current at, 85 C (1) Useful life at 85 C and I R applied: 1500 h T amb ( C) (1) ig. 5 - Multiplier of useful life as a function of ambient temperature and ripple current load Table 4 MULTIPLIER O RIPPLE CURRENT (I R ) AS A UNCTION O REQUENCY REQUENCY (Hz) I R MULTIPLIER Table 5 TEST PROCEDURES AND REQUIREMENTS TEST PROCEDURE NAME O TEST REERENCE (quick reference) Endurance Useful life Shelf life (storage at high temperature) IEC / EN , subclause 4.13 CECC 30301, subclause IEC / EN , subclause 4.17 T amb = 85 C; U R applied; 1000 h T amb = 85 C; U R and I R applied; 1500 h T amb = 85 C; no voltage applied; 500 h After test: U R to be applied for 30 min, 24 h to 48 h before measurement REQUIREMENTS C/C: ± 20 % tan 2 x spec. limit C/C: ± 50 % tan 3 x spec. limit Z 3 x spec. limit no short or open circuit total failure percentage: 3 % C/C, tan, Z: or requirements see Endurance test above Statements about product lifetime are based on calculations and internal testing. They should only be interpreted as estimations. Also due to external factors, the lifetime in the field application may deviate from the calculated lifetime. In general, nothing stated herein shall be construed as a guarantee of durability. Revision: 14-eb-17 4 Document Number: 28307

5 Legal Disclaimer Notice Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, UNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, Vishay ), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer s technical experts. Product specifications do not expand or otherwise modify Vishay s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 08-eb-17 1 Document Number: 91000