EMC TEST REPORT. Page: 1 of 41. : Netion Electronic Co., Ltd. : Fanhu Industrial Park, Sanshui, Foshan, Guangdong, China. Equipment Under Test (EUT) :

Transcription

1 Page: 1 of 41 EMC TEST REPORT Reference No. Applicant Address : WT F-E : Netion Electronic Co., Ltd. : Fanhu Industrial Park, Sanshui, Foshan, Guangdong, China. Equipment Under Test (EUT) : Product Name : Uninterruptible Power Systems Model No. : C1K, C2K, C3K, C1KS,C2KS,C3KS Standards : EN :2006 EN :2006 EN :1995+A2:2005 Date of Test : May 18, 2008 Test Engineer : Maikou.zhang Reviewed By : Test Result : PASS * * The sample detailed above has been tested to the requirements of Council Directives 2004/108/EC. The test results have been reviewed against the Directives above and found to meet their essential requirement

2 Page:2 of 41 1 Test Summary Test Test Requirement Test Method Class / Severity Result Mains Terminal Disturbance Voltage, 150kHz to 30MHz Radiation Emission, 30MHz to 1000MHz Harmonic Emission on AC, 100Hz to 2kHz Flicker Emission on AC EN :2006 EN :2006 EN :2006 EN :2006 EN : 2006 EN : 2006 EN :1995+A2:2005 ESD EN :2006 Radiated Immunity (80MHz to 1GHz) Electrical Fast Transients (EFT) on AC and DC EN :1995+A2:2005 EN : A1:2001 EN :2006 EN :2006 Table 1of EN Table 3 of EN Clause 7 of EN Clause 5 of EN ±4 kv Contact ±8 kv Air 3V/m, 80%, 1kHz, Amp. Mod. PASS PASS PASS PASS PASS PASS EN :2006 EN :2004 AC ±1.0kV PASS Surge Immunity on AC EN :2006 EN :2006 Injected Currents on AC & DC, 150kHz to 80MHz Power frequency magnetic field immunity Voltage Dips and Interruptions on AC Remark: A.M. Amplitude Modulation. P.M. Pulse Modulation. D.M. Differential Mode * U T is the nominal supply voltage EN :2006 EN :2006 EN :1996 +A1: 2001 EN :1993+A1:2001 EN :2006 EN :2004 ±1kV D.M. ±2kV C.M. 3Vrms(emf), 80%, 1kHz Amp. Mod. 3A/m >95 % U T * for 250per 30 % U T * for 25per >95 % U T * for 0.5per PASS PASS N/A N/A

3 Page:3 of 41 2 Contents 1 TEST SUMMARY CONTENTS GENERAL INFORMATION CLIENT INFORMATION GENERAL DESCRIPTION OF E.U.T DETAILS OF E.U.T TEST INSTRUCTION DESCRIPTION OF SUPPORT UNITS STANDARDS APPLICABLE FOR TESTING TEST FACILITY TEST LOCATION EQUIPMENT USED DURING TEST EMISSION TEST RESULTS MAINS TERMINALS DISTURBANCE VOLTAGE, 150KHZ TO 30MHZ E.U.T. Operation Measurement Data Conducted Emissions Test Data Photographs Mains Terminal Disturbance Voltage on AC Test Setup RADIATION EMISSION DATA Measurement Uncertainty EUT Setup Spectrum Analyzer Setup Test procedure Corrected Amplitude & Margin Calculation Summary of Test Results Radiated Emissions Test Data Photographs Radiation Emission Test Setup HARMONICS TEST RESULTS FLICKER TEST RESULT Photographs Harmonics & Flicker Test Setup IMMUNITY TEST RESULTS PERFORMANCE CRITERIA DESCRIPTION ESD E.U.T. Operation Direct Application Test Results Indirect Application Test Results Photographs - ESD Test Setup RADIATED IMMUNITY E.U.T. Operation Test Results Photographs - Radiated Immunity Test Setup For X-Direction ELECTRICAL FAST TRANSIENTS (EFT) E.U.T. Operation Page

4 Page:4 of Test Results On AC Cable Photographs : EFT Test Setup For EUT On AC Cable SURGE E.U.T. Operation Test Results Photographs : Surge Test Setup CONDUCTED IMMUNITY 0.15MHZ TO 80MHZ E.U.T. Operation Test Results AC mains of AC Cable Photographs : Conducted Immunity Test Setup On AC Cable PHOTOGRAPHS - CONSTRUCTIONAL DETAILS EUT - FRONT VIEW EUT - BACK VIEW EUT - OPEN VIEW PCB1 - FRONT VIEW PCB 1- BACK VIEW PCB 2- FRONT VIEW PCB2 - BACK VIEW PCB 3- FRONT VIEW PCB 3- BACK VIEW CE LABEL... 41

5 Page:5 of 41 3 General Information 3.1 Client Information Applicant: Address of Applicant: Manufacturer: Address of Manufacturer: Netion Electronic Co., Ltd. Fanhu Industrial Park, Sanshui, Foshan, Guangdong, China. Netion Electronic Co., Ltd. Fanhu Industrial Park, Sanshui, Foshan, Guangdong, China. 3.2 General Description of E.U.T. Product Name: Model No.: 3.3 Details of E.U.T. Power Supply: Uninterruptible Power Systems C1K, C2K, C3K, C1KS,C2KS,C3KS AC V, 50Hz 3.4 Test Instruction The EMI pretests were performed in the condition of the power supply from 220 to 240V and 50Hz, compliance test in 230V/50Hz since no worst case be found. Then all the tests were performed in the condition of AC 230V/50Hz input. 3.5 Description of Support Units The EUT has been tested as an independent unit. 3.6 Standards Applicable for Testing The customer requested EMC tests for an Uninterruptible Power Systems. The standards used were EN , EN and EN for emissions & EN for immunity. Table 1 : Tests Carried Out Under EN :2006 Standard Status EN :2006 Radiation Emission, 30MHz to 1000MHz EN :2006 Mains Terminal Disturbance Voltage,150KHz to 30MHz

6 Page:6 of 41 Table 2 : Tests Carried Out Under EN : 2006 & EN :1995+A2:2005 EN :2006 Harmonic Emissions on AC EN :1995+A2:2005 Flicker Emissions on AC Indicates that the test is applicable Indicates that the test is not applicable Table 3 : Tests Carried Out Under EN :2006 Standard Status EN :1995+ A2:2001 Electro-static discharge EN :2006 Radio frequency EM fields (80MHz to 1GHz) EN :2004 Fast transients EN :2006 Surges EN :1996+A1: 2001 Radio frequency continuous conducted (150kHz to 80MHz) EN :1993+A1: 2001 Power-frequency magnetic field (50Hz) EN :2004 Voltage dips & interruptions Indicates that the test is applicable Indicates that the test is not applicable

7 Page:7 of Test Facility The test facility is recognized, certified, or accredited by the following organizations: FCC Registration No.: Solid Industrial (Shenzhen) Co., Ltd. EMC Laboratory has been registered and fully described in a report filed with the (FCC) Federal Communications Commission. The acceptance letter from the FCC is maintained in our files. Registration , December 28, Test Location All Emissions testswere performed at:- Solid Industrial (Shenzhen) Co., Ltd. at 333 Bulong Highway Buji Longgang, Shenzhen, Guangdong, China. Its VCCI Registration No.: 2153.

8 Page:8 of 41 4 Equipment Used during Test Equipment Brand Name Model Cal. Int Months Last Cal. Date 3m Anechoic chamber EMC Analyzer Agilent E7402A EMI Test Receiver R&S ESS Pre Amplifier Anritsu MH648A Bilog Antenna SCHAFFNER CBL6111C AM/FM Stereo Signal Generator Panasonic VP-8122A Signal Generator R&S SMG RF Selector TOYO NS4901A - - Turn Disc HD DS4150S - - Antenna Mast HD MA EMI Shielded Room Spectrum analyzer ADVANTEST R3261C EMI Test Receiver R&S ESPI Pre Amplifier Anritsu MH648A LISN R&S ENV LISN Kyoritsu KNW LISN Kyoritsu KNW-242C Absorbing Clamp R&S MDS Absorbing Clamp R&S MDS Absorbing Clamp Kyoritsu KT Distortion Meter MEGURO MAK-6578A AM/FM Stereo Signal Generator Panasonic VP-8122A Oscilloscope LEADER LS Function Generator National VP-7422A Signal Generator R&S SMG RF Selector TOYO NS RF Selector TOYO NS

9 Page:9 of 41 Remote Controller TOYO MAC - - Harmonic & Flicker Test Signal Conditioning Unit SCHAFFNER CCN Signal Phase Impedance Network SCHAFFNER INA KVA AC Power Source SCHAFFNER NSG1007 List Of Test Equipment For EMS Equipment Brand Name Model Cal. IntLast Cal. Date Months 3m Anechoic chamber Power Reflection Meter R&S NAP RF Power Amplifier TOYO AS300SSS Distortion Meter HM-250 KNEWOOD Synthesized Function Generator FC110 YOKOGAWA Noise Meter MEGURO MN-446A AM/FM Stereo Signal Generator Panasonic VP-8122A Oscilloscope LEADER LS Function Generator National VP-7422A Signal Generator R&S SMG Turn Disc HD DS4150S - - Isotropic Field Monitor AR FM Antenna Mast HD MA RF Selector TOYO NS4901A - - Remote Controller TOYO MAC - - TEST Room Fast Transient Burst Generator SCHAFFENR NSG AC Power Supply KIKUSUI PCR2000L Electrostatic Discharge Simulator Noiseken ESS-200AX AM/FM Stereo Signal Generator Panasonic VP-8122A Function Generator National VP-7422A AC Power Supply KIKUSUI PCR4000L Shielded Room

10 Page:10 of 41 Spectrum analyzer ADVANTEST R3261C EMI Test Receiver R&S ESS Absorbing Clamp R&S MDS Milli-Voltmeter R&S URV Absorbing Clamp Kyoritsu KT Signal Generator R&S SMG Oscilloscope LEADER LS Audio Analyzer R&S UPA Milli-voltmeter R&S URV Filter Unit TOYO NF RF Power Amplifier EN 411LA RF Selector TOYO NS RF Selector TOYO NS RF Selector TOYO NS Injection&Output Network for Audio Output Kyoritsu KSI-5104U - - Mains Rejection Network Kyoritsu KSI-2004S - - Mains Rejection Network Kyoritsu KSI Coupling Network L Erika Fiedler Coupling Network A Erika Fiedler Coupling Network M Erika Fiedler Rco Network(8Ω) Erika Fiedler Mains Filter Erika Fiedler Surge Module EMC Partner EBC Digital Oscilloscope Tektronix TDS TRACS-Lite Ver. 2.4 (3M INSTALL P/W) EMC PARTNER TRA1Z65B Ultra Compact Generator EM Test UCS500-M Conducted Immunity Test Signal Generator ROHDE & SCHWARZ SMY Amplifier MHz OPHIRRF GRF Power Meter ROHDE & SCHWARZ NRVS

11 Page:11 of 41 Power Sensor ROHDE & SCHWARZ NRV-Z Dual Directional Coupler WERLATONE INC. C Oscilloscope Type 485 TEKTRONIX CDN M2 SCHAFFNER CHASE CDN-M Immunity S/W Ver 4.31 SCHAFFNER CHASE CIS C/S Tester EM Test CIT Signal Generator Radiated Immunit test ROHDE & SCHWARZ SMY Signal Generator R&S SMG Noise Meter MEGURO MN-446A Pre Amplifier Anritsu MH648A Bilog Antenna SCHAFFNER CBL6111C Antenna Mast HD MA Turn Disc HD DS4150S 12 -

12 Page:12 of 41 5 Emission Test Results 5.1 Mains Terminals Disturbance Voltage, 150kHz to 30MHz Test Requirement: EN Test Method: EN Test Date: May 18, 2008 Frequency Range: 150kHz to 30MHz Class/Severity: Table 1 of EN Detector: Peak for pre-scan (9kHz Resolution Bandwidth) Quasi-Peak & Average if maximised peak within 6dB of Average Limit E.U.T. Operation Operating Environment: Temperature: 24.0 C Humidity: 52 % RH Atmospheric Pressure: 1012 mbar EUT Operation : The EUT was placed on the test table in working mode and connected with the full load. The maximised peak emissions from the EUT was scanned and measured for both the Live and Neutral Lines. Quasi-peak & average measurements were performed if peak emissions were within 6dB of the average limit line Measurement Data An initial pre-scan was performed on the live and neutral lines. No futher quasi-peak or average measurements were performed since no peak emissions were detected within 10dB line below the average limit. Please refer to the following peak scan graph for reference. Remark: More than 15dB margin

13 Page:13 of Conducted Emissions Test Data

14 Page:14 of Photographs Mains Terminal Disturbance Voltage on AC Test Setup

15 Page:15 of Radiation Emission Data Test Requirement: EN Test Method: EN Test Date: May 18, 2008 Frequency Range: 30MHz to 1000MHz Class/Severity: Table 1 of EN Detector: Peak for pre-scan (120kHz Resolution Bandwidth) Quasi-Peak & Average if maximised peak within 6dB of Average Limit Measurement Uncertainty All measurements involve certain levels of uncertainties, especially in the field of EMC. The factors contributing to uncertainties are spectrum analyzer, cable loss, antenna factor calibration, antenna directivity, antenna factor variation with height, antenna phase center variation, antenna factor frequency interpolation, measurement distance variation, site imperfections, mismatch (average), and system repeatability. Based on NIS 81, The Treatment of Uncertainty in EMC Measurements, the best estimate of the uncertainty of a radiation emissions measurement at Solid EMC Lab is +4.0 db EUT Setup The radiated emission tests were performed in the 3m Semi- Anechoic Chamber test site, using the setup accordance with the CISPR16-1, The specification used in this report was the EN limits. The EUT was placed on the test table in working mode and connected with the full load Spectrum Analyzer Setup According to EN Class B Rules, the system was tested to 1000 MHz. Start Frequency...30 MHz Stop Frequency MHz Sweep Speed Auto IF Bandwidth...1 MHz

16 Page:16 of 41 Video Bandwidth...1 MHz Quasi-Peak Adapter Bandwidth khz Quasi-Peak Adapter Mode...Normal Resolution Bandwidth...1MHz Test procedure The radiated emissions test. Maximizing procedure was performed on the six (6) highest emissions to ensure EUT is compliant with all installation combinations. All data was recorded in the peak detection mode. Quasi-peak readings was performed only when an emission was found to be marginal (within -4 dbμv of specification limits), and are distinguished with a "Qp" in the data table. The EUT was under normal mode during the final qualification test and the configuration was used to represent the worst case results Corrected Amplitude & Margin Calculation The Corrected Amplitude is calculated by adding the Antenna Factor and Cable Factor, and subtracting the Amplifier Gain from the Amplitude reading. The basic equation is as follows: Corr. Ampl. = Indicated Reading + Antenna Factor + Cable Factor - Amplifier Gain The Margin column of the following data tables indicates the degree of compliance with the applicable limit. For example, a margin of -7dBμV means the emission is 7dBμV below the maximum limit for Class B. The equation for margin calculation is as follows: Margin = Corr. Ampl. Class B Limit Summary of Test Results According to the data in section 5.2.7, the EUT complied with the EN standards, and had the worst margin of:

17 Page:17 of Radiated Emissions Test Data Job No.: Polarziation: Vertical Standard: EN55022 RE-Class B 3M Power Source: AC 230V/50Hz Test item: Radiation Test Date: 08/05/18/ Temp.( )/Hum.(%RH): 26( )/60%RH Time: 11/57/27 EUT: UPS Test By: Model: C3K Distance: 3m No. Frequency Reading Correct Result Limit Margin Degree Height Remark (MHz) (dbuv/m) Factor(dB) (dbuv/m) (dbuv/m) (db) ( ) (cm) peak peak QP peak peak

18 Page:18 of 41 Job No.: Polarziation: Horizontal Standard: EN55022 RE-Class B 3M Power Source: AC 230V/50Hz Test item: Radiation Test Date: 08/05/18/ Temp.( )/Hum.(%RH): 26( )/60%RH Time: 11/53/10 EUT: UPS Test By: Model: C3K Distance: 3m No. Frequency Reading Correct Result Limit Margin Degree Height Remark (MHz) (dbuv/m) Factor(dB) (dbuv/m) (dbuv/m) (db) ( ) (cm) peak peak QP peak peak

19 Page:19 of Photographs Radiation Emission Test Setup

20 Page:20 of Harmonics Test Results Test Requirement: EN Test Method: EN Frequency Range: 100Hz to 2kHz Test Result: PASS There is no need for Harmonics test to be performed on this product (rated power is less than 75W) in accordance with EN For further details, please refer to Clause 7, Note 1 of EN which states:- For the following categories of equipment limits are not specified in this edition of the standard. Note 1: Equipment with a rated power of 75W or less, other than lighting equipment.

21 Page:21 of 41 Current Test Result Summary (Run time) EUT: Uninterruptible Power Systems Tested by: Wei Shanguo Test category: Class-A per A-14 (European limits) Test Margin: 100 Test date: 5/18/2008 Start time: 5:04:26 PM End time: 5:07:06 PM Test duration (min): 2.5 Data file name: H cts_data Comment: Full Load Customer: Netion Electronic Co., Ltd. Test Result: Pass Source qualification: Normal THC(A): 0.06 I-THD(pk%): POHC(A): POHC Limit(A): Harm# Harms(avg)100%Limit%of LimitHarms(max)150%Limit %of Limit Status Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass

22 Page:22 of 41 Voltage Source Verification Data (Run time) EUT: Uninterruptible Power Systems Tested by: Wei Shanguo Test category: Class-A per A-14 (European limits) Test Margin: 100 Test date: 5/18/2008 Start time: 5:04:26 PM End time: 5:07:06 PM Test duration (min): 2.5 Data file name: H cts_data Comment: Full Load Customer: Netion Electronic Co., Ltd. Test Result: Pass Source qualification: Normal Harm# Harmonics V-rms Limit V-rms % of Limit Status OK OK OK OK OK OK OK OK OK OK OK OK OK OK OK OK OK OK OK OK OK OK OK OK OK OK OK OK OK OK OK OK OK OK OK OK OK OK OK

23 Page:23 of Flicker Test Result Test Requirement: EN Test Method: EN Test Result: PASS Report title: Company Name: Waltek Services Date of test: 16: May 2008 Tester: Wei Shanguo Standard used: EN/IEC Flicker Short time (Pst): 10 min Observation time: 10 min (1 Flicker measurement) Customer: Netion Electronic Co., Ltd. E. U. T.: Uninterruptible Power Systems AC 230V, 50Hz Test Result PASS

24 Page:24 of 41 Maximum Flicker results EUT values Limit Result Pst PASS dc [%] PASS dmax [%] PASS dt [s] PASS Photographs Harmonics & Flicker Test Setup

25 Page:25 of 41 6 Immunity Test Results 6.1 Performance Criteria Description Criterion A: The apparatus shall continue to operate as intended. No degradation of performance or loss of function is allowed below a performance level specified by the manufacturer, when the apparatus is used as intended. Criterion B: The apparatus shall continue to operate as intended after the test. No degradation of performance or loss of function is allowed below a performance level specified by the manufacturer, when the apparatus is used as intended. Criterion C: Temporary loss of function is allowed, provided the function is self recoverable or can be restored by the operation of the controls. For further details, please refer to of EN ESD Test Requirement: EN Test Method: EN Test Date: May 18, 2008 Discharge Impedance: 330 Ω / 150 pf Discharge Voltage: Air Discharge: 8 kv Contact Discharge: 4 kv HCP & VCP: 4 kv Polarity: Positive & Negative Number of Discharge: Minimum 10 times at each test point Discharge Mode: Single Discharge Discharge Period: 1 second minimum E.U.T. Operation Operating Environment: Temperature : 24.0 C Humidity : 52 % RH Barometric Pressure : 1012 mbar EUT Operation: The EUT was placed on the test table in working mode and connected with the full load.

26 Page:26 of Direct Application Test Results Observations : Test points : 1. All Exposed Surface & Seams; 2. All metallic part Direct Application Test Results Discharge Level (kv) Polarity (+/-) Test Point Contact Discharge Air Discharge 8 +/- 1 N/A A 4 +/- 2 A N/A Results A: No degradation in the performance of the E.U.T. was observed. N/A: Not applicable Indirect Application Test Results Observations : Test points : 1. All sides. Indirect Application Test Results Discharge Level (kv) Polarity (+/-) Test Point Horizontal Coupling Vertical Coupling 4 +/- 1 A A Results A: No degradation in the performance of the E.U.T. was observed.

27 Page:27 of Photographs - ESD Test Setup

28 Page:28 of Radiated Immunity Test Requirement: EN Test Method: EN Frequency Range: 80MHz 1GHz Face Under Test: Three Mutually Orthogonal Faces Severity: 3V/m, 1kHz, 80% Amp. Mod. from 80MHz to 1GHz Test Date: May 18, E.U.T. Operation Operating Environment: Temperature: 24.0 C Humidity: 52 % RH Barometric Pressure: 1012 mbar EUT Operation: The EUT was placed on the test table in working mode and connected with the full load Test Results Frequency Level Modulation EUT Face Result / Observations 80MHz- 1GHz 3V/m 1kHz, 80%, Amp. Mod. Remarks: AM : Amplitude Modulation. PM : Pulse Modulation. X : EUT as per photograph in section of this report. Y : As X, but rotate EUT by 90 clockwise. Z : As Y, but rotate EUT by 90 vertically. Results A: No degradation in the performance of the E.U.T. was observed. X Y Z During test and after test, the EUT was normal (A).

29 Page:29 of Photographs - Radiated Immunity Test Setup For X-Direction

30 Page:30 of Electrical Fast Transients (EFT) Test Requirement: EN Test Method: EN Test Date: May 18, 2008 Test Level: 1.0kV on AC Polarity: Positive & Negative&PE Repetition Frequency: 5kHz Burst Duration: 300ms Test Duration: 2 minutes per level & polarity Test Ports: AC Input & Output Ports E.U.T. Operation Operating Environment: Temperature: 24.0 C Humidity: 52 % RH Barometric Pressure: 1012 mbar EUT Operation: Compliance test was performed test in working mode with the full load Test Results On AC Cable Lead under Test AC Live AC Neutral AC Live & Neutral &PE Level (±kv) ±1.0 ±0.5 ±1.0 ±0.5 ±1.0 ±0.5 Coupling Direct/Clamp EUT operating mode Observations (Performance Criterion) Direct ON and Idle mode B Direct ditto B Direct ditto B Results B: During test, This was within the minimum performance criteria set by the Please refer to section 6.1 of this report for further details.

31 Page:31 of Photographs : EFT Test Setup For EUT On AC Cable

32 Page:32 of Surge Test Requirement: EN Test Method: EN Test Date: May 18, 2008 Test level: ±1kV Live to Neutral, ±2kV L&N-PE Interval: 60s between each surge No. of surges: 5 positive, 5 negative at 0, 90, 180, 270. Test Ports: AC Input & Output Ports E.U.T. Operation Operating Environment: Temperature: 24.0 C Humidity: 52 % RH Barometric Pressure: 1012 mbar EUT Operation: Compliance test was performed test in working mode with the full load Test Results Level Voltage Poll Path Pass Fail 1 0.5kV ± L-N, L-PE, N-PE / / 2 1kV ± L-N B / 3 2kV ± L-PE, N-PE, B / 4 4kV ± L-N, L-PE, N-PE / / Results B: During test, This was within the minimum performance criteria set by the Please refer to section 6.1 of this report for further details.

33 Page:33 of Photographs : Surge Test Setup

34 Page:34 of Conducted Immunity 0.15MHz to 80MHz Test Requirement: EN Test Method: EN Test Date: May 18, 2008 Frequency Range: 0.15MHz to 80MHz Test level: 3V rms (unmodulated emf into 150 Ω) Modulation: 80%, 1kHz Amplitude Modulation. Test Ports: AC Input & Output Ports E.U.T. Operation Operating Environment: Temperature: 24.0 C Humidity: 52 % RH Barometric Pressure: 1012 mbar EUT Operation: Compliance test was performed test in working mode with the full load Test Results AC mains of AC Cable Frequency Line Test Level Modulation Step Size 150kHz to 80MHz 2 Wire AC Supply Cable 3Vrms 80%, 1kHz Amp. Mod. Dwell Time 1% 1s Observation (Performance Criterion) During test and after test, the EUT was normal (A). Results A: No degradation in the performance of the E.U.T. was observed.

35 Page:35 of Photographs : Conducted Immunity Test Setup On AC Cable

36 Page:36 of 41 7 Photographs - Constructional Details 7.1 EUT - Front View 7.2 EUT - Back View

37 Page:37 of EUT - Open View

38 Page:38 of PCB1 - Front View 7.5 PCB 1- Back View

39 Page:39 of PCB 2- Front View 7.7 PCB2 - Back View

40 Page:40 of PCB 3- Front View 7.9 PCB 3- Back View

41 Page:41 of 41 8 CE Label 1. The CE conformity marking must consist of the initials CE taking the following form: If the CE marking is reduced or enlarged, the proportions given in the above graduated drawing must be respected. 2. The CE marking must have a height of at least 5 mm except where this is not possible on account of the nature of the apparatus. 3. The CE marking must be affixed to the product or to its data plate. Additionally it must be affixed to the packaging, if any, and to the accompanying documents. 4. The CE marking must be affixed visibly, legibly and indelibly. It must have the same height as the initials CE Proposed Label Location on EUT EUT Bottom View/proposed CE Mark Location