SGS-CSTC Standards Technical Services. SGS-CSTC(Shanghai)Co.,Ltd EMC TEST REPORT SHEMO AV01-A2 LINCON AUTOMATION CO., LTD

Transcription

1 No. 588 West Jindu Road, Songjiang District, Shanghai, China SGS-CSTC Standards Telephone: +86 (0) Fax: +86 (0) Application No.: Applicant: Equipment Under Test (EUT): EMC TEST REPORT SHEMO AV01-A2 LINCON AUTOMATION CO., LTD Page 1 of 40 NOTE: The following sample(s) submitted was/were identified on behalf of the client as EUT Name: LinCon HMI Model No.: LC104S, LC057S, LC080S, LC121S, LC150S, LC057SL, LC070SL, LC080SL, LC104SL Serial No.: Not supplied by client Standards: EN 55011: 2007/A2:2007 EN : 2005 EN : 2006+A1:2009+A2:2009 EN : 2008 Date of Receipt: Dec. 31, 2008 Date of Test: Jan. 08, 2009 to Jan. 12, 2009 Date of Issue: Dec. 29, 2011 Test Result : PASS The CE mark as shown below can be used, under the responsibility of the manufacturer, after completion of an EC Declaration of Conformity and compliance with all relevant EC Directives. Jim Xu E&E Section Head SGS-CSTC Liky Zhu E&E Project Engineer SGS-CSTC(Shanghai)Co.,Ltd Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company s findings at the time of its intervention only and within the limits of Client s instructions, if any. The Company s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to thesample(s) tested and such sample(s) are retained for 90 days only Member of the SGS Group (Société Générale de Surveillance)

2 2 Test Summary SGS-CSTC Standards Page: 2 of 43 Test Test Requirement Test Method Class / Severity Result Conducted Emission (150K to 30MHz) Radiated Emission (30MHz to 1000MHz) EN 55011: 2007/A2:2007 EN 55011: 2007/A2:2007 Class A PASS EN 55011: 2007/A2:2007 EN 55011: 2007/A2:2007 Class A PASS Harmonic Current Emission on AC, up to 2kHz EN : 2006+A1:2009+A2:2009 EN : 2006+A1:2009+A2:2009 Clause 7 of EN PASS Voltage Fluctuation and Flicker on AC EN : 2008 EN : 2008 ESD EN : 2005 IEC :2001 Radio-Rrequency Rlectromagnetic Field.,80MHz to 1 GHz,1.4GHz to 2 GHz,2GHz to 2.7 GHz Electrical Fast Transients (EFT) on AC EN : 2005 IEC : 2008 Clause 5 of EN Contact Air 10V/m 3V/m ±4 kv ±8 kv 1V/m 80%, 1kHz, AM EN : 2005 IEC :2004 ±2.0kV Surges on AC EN : 2005 IEC :2005 Injected Currents on AC, 150kHz to 80MHz Power-frequency magnetic field Voltage Dips and Interruptions on AC EN : 2005 IEC :2006 EN : 2005 IEC :2001 EN : 2005 IEC :2004 ±1.0kV D.M. ±2.0kV C.M. 10Vrms (emf), 80%, 1kHz Amp. Mod. 50,60 Hz 30A/m 0 % UT* for1per 40 % UT* for10per 70 % UT* for 25per 0 % UT* for 250per PASS PASS PASS PASS PASS PASS N/AΨ PASS

3 Page: 3 of 43 Remark: * U T is the nominal supply voltage. D.M. Differential Mode. C.M. Common Mode. Ψ N/A Not Applicable Note: 1.According to the validated standards, the models mentioned in the report SHEMO AV01-A1 issued by SGS-CSTC. So the models in this report are deemed to fulfil the EMC requirements without testing. 2.The Power-frequency magnetic field test will not apply to the quipment containing no Components susceptible to magnetic fields, such as Hall elements or magnetic field sensors, according to EN

4 3 Contents SGS-CSTC Standards Page: 4 of 43 1 COVER PAGE TEST SUMMARY CONTENTS GENERAL INFORMATION CLIENT INFORMATION GENERAL DESCRIPTION OF E.U.T DETAILS OF E.U.T DESCRIPTION OF SUPPORT UNITS STANDARDS APPLICABLE FOR TESTING DEVIATION FROM STANDARDS ABNORMALITIES FROM STANDARD CONDITIONS MONITORING OF EUT FOR ALL IMMUNITY TEST TEST LOCATION TEST FACILITY...ERROR! BOOKMARK NOT DEFINED. 5 EQUIPMENTS USED DURING TEST EMISSION TEST RESULTS CONDUCTED EMISSIONS MAINS TERMINALS, 150KHZ TO 30MHZ E.U.T. Operation Measurement Data RADIATED EMISSIONS (30MHZ TO 1GHZ) E.U.T. Operation Measurement Data HARMONICS TEST RESULTS Measurement Diagram and Data FLICKER TEST RESULT Test Results: IMMUNITY TEST RESULTS PERFORMANCE CRITERIA DESCRIPTION IN CLAUSE 4 OF EN : ESD E.U.T. Operation Direct Application Test Results RADIO FREQUENCY ELECTROMAGNETIC FIELDS TEST E.U.T. Operation Test Results ELECTRICAL FAST TRANSIENTS (EFT) E.U.T. Operation Test Results On AC Supply: SURGES E.U.T. Operation Test Results: Pass Page

5 Page: 5 of INJECTED CURRENTS 0.15MHZ TO 80MHZ E.U.T. Operation Test Results: VOLTAGE DIPS AND INTERRUPTIONS E.U.T. Operation Test Results: PHOTOGRAPHS CONDUCTED EMISSION TEST SETUP RADIATED EMISSION TEST SETUP HARMONIC&FLICKER TEST SETUP ESD TEST SETUP RADIO FREQUENCY ELECTROMAGNETIC FIELDS TEST SETUP SURGE/ VOLTAGE DIPS AND INTERRUPTIONS TEST SETUP EFT TEST SETUP INJECTED CURRENTS TEST SETUP EUT CONSTRUCTIONAL DETAILS... 36

6 Page: 6 of 43 4 General Information 4.1 Client Information Applicant: LINCON AUTOMATION CO., LTD Address of Applicant: RM2146, BUILDING E, OVERSEAS SCHOLAR BUSINESS PARK, EAST LAKE HIGH-TECH DEVELOPMENT ZONE, WUHAN, P.R.C Manufacturer: LINCON AUTOMATION CO., LTD Address of RM2146, BUILDING E, OVERSEAS SCHOLAR BUSINESS Manufacturer: PARK, EAST LAKE HIGH-TECH DEVELOPMENT ZONE, WUHAN, P.R.C 4.2 General Description of E.U.T. EUT Name: LinCon HMI Model No.: LC104S, LC057S, LC080S, LC121S, LC150S, LC057SL, LC070SL, LC080SL, LC104SL Brand Name Not supplied by client Serial No.: Not supplied by client 4.3 Details of E.U.T. Power Supply: AC230V Power Cord: About 1,5m 4.4 Description of Support Units Name / Function Model No. Remark N/A N/A N/A 4.5 Standards Applicable for Testing The customer requested EMC tests for LinCon HMI. The standards used were EN 55011: 2007/A2:2007, EN : 2005, EN : 2006+A1:2009+A2:2009 and EN : Table 1 : Tests Carried Out Under EN 55011: 2007/A2:2007 Standard EN 55011: 2007/A2:2007 Conducted Emission EN 55011: 2007/A2:2007 Radiated Emissions Indicates that the test is not applicable Indicates that the test is applicable Status

7 Page: 7 of 43 Table 2: Tests Carried Out Under EN : 2006+A1:2009+A2:2009 & EN : 2008 Standard EN : 2006+A1:2009+A2:2009 Harmonic Current Emission on AC EN : 2008 Voltage Fluctuation and Flicker on AC Indicates that the test is not applicable Indicates that the test is applicable Status Table 3: Tests carried out under EN : 2005 Standard IEC :2001 Electrostatic discharge test IEC : 2008 Radio frequency electromagnetic fields test Status IEC :2004 Electrical fast transients/burst test IEC :2005 Surges test IEC :2006 Injected Currents test IEC :2001 Power-frequency magnetic field immunity test IEC :2004 Voltage dips and interruptions test Indicates that the test is not applicable Indicates that the test is applicable Note The EUT does not contain any component which is susceptible from the magnetic field. 4.6 Deviation from Standards None. 4.7 Abnormalities from Standard Conditions None. 4.8 Monitoring of EUT for All Immunity Test Visual: 4.9 Test Location All tests were performed at:

8 SGS-CSTC Standards No.588 West Jindu Road, Songjiang District, Shanghai, China Tel: Fax: Page: 8 of Test Confident level The test facility is recognized, certified, or accredited by the following organizations: CNAS (No. CNAS L0599) CNAS has accredited SGS-CSTC Standards to ISO/IEC 17025:2005 General Requirements for the Competence of Testing and Calibration Laboratories (CNAS-CL01 Accreditation Criteria for the Competence of Testing and Calibration Laboratories) for the competence in the field of testing. Date of expiry: FCC Registration No.: SGS-CSTC Standards has been registered and fully described in a report filed with the Federal Communications Commission (FCC). The acceptance letter from the FCC is maintained in our files. Registration No.: , Expiry Date: Industry Canada (IC) IC Assigned Code: 8617A The 3m Semi-anechoic chamber of SGS-CSTC Standards has been registered by Certification and Engineering Bureau of Industry Canada for radio equipment testing with Registration No.: 8617A. Expiry Date: VCCI (Member No.: 3061) The 3m Semi-anechoic chamber and Shielded Room of SGS-CSTC Standards has been registered in accordance with the Regulations for Voluntary Control Measures with Registration No.: R-3172 and C-3514 respectively. Date of Registration: Date of Expiry: Measurement Uncertainty According to CISPR Test Item Frequency Range Measurement Uncertainty Conducted Emission 150KHz 30MHz 3.5dB Radiated Emission 30MHz 1000MHz 4.0dB Note: The measurement uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2.

9 Page: 9 of 43 5 Equipments Used during Test Conducted Emission Item Test Equipment Manufacturer Model No. Serial No. Cal. Date Cal. Due date 1 EMI test receiver Rohde & Schwarz ESCS Line impedance stabilization network ETS 3816/ Radiated Emission Item Test Equipment Manufacturer Model No. Serial No. Cal. Date Cal. Due date 1 EMI test receiver Rohde & Schwarz ESU Antenna SCHWARZBECK VULB CONTROLLER INNCO CO / / Harmonic &Flicker Item Test Equipment Manufacturer Model No. Series No. Cal. Date Cal. Due date Single phase 1 harmonics&flicker EM test DPA500 V analyzer 2 AC SOURCE 6KVA EM test ACS500 V Electrostatic Discharge Test Item Test Equipment Manufacturer Model No. Series No. Cal. Date Cal. Due date 1 Electrostatic Discharge Simulator KIKUSUI KES4021 LL

10 Page: 10 of 43 Radio Frequency Electromagnetic Fields Test Item Test Equipment Manufacturer Model No. Serial No. Cal. Date Cal. Due date 1 Ultra broadband antenna Rohde & Schwarz HL amplifier AR 30W1000B amplifier AR 30S1G power meter Rohde & Schwarz NRP Single generator Rohde & Schwarz SMR EFT Test Item Test Equipment Manufacturer Model No. Series No. Cal. Date Cal. Due date 1 Ultra-compact simulator EM test UCS500M4 V Surge Test Item Test Equipment Manufacturer Model No. Series No. Cal. Date Cal. Due date 1 Ultra-compact simulator EM test UCS500M4 V Voltage dips and Interruption Test Item Test Equipment Manufacturer Model No. Series No. Cal. Date Cal. Due date 1 Ultra-compact simulator EM test UCS500M4 V Motorised Variac EM test MV2616 V Injected Currents Test Item Test Equipment Manufacturer Model No. Series No. Cal. Date Cal.Due date 1 AM/FM signal generator AEROFLEX 2023A / PAMP Conducted RF test system HAEFFLY PAMP

11 Page: 11 of 43 3 CDN impedance and K-factor LUTHI L-801 M2/M / / General Equipment Item Test Equipment Manufacturer Model No. Serial No. Cal. Date Cal.Due date 1 Atmosphere meter pressure Shanghai ZhongXuan Electronic Co;Ltd BY-2003P / CLAMP METER FLUKE Thermo-Hygrometer ZHICHEN ZC Digital meter illuminance TES electrical electronic Corp. TES-1330A

12 Page: 12 of 43 6 Emission Test Results 6.1 Conducted Emissions Mains Terminals, 150kHz to 30MHz Test Requirement: EN 55011: 2007/A2:2007 Test Method: EN 55011: 2007/A2:2007 Test Date: Jan. 08, 2009 Frequency Range: 150KHz to 30MHz Class / Severity: Class A Detector: Peak for pre-scan (9kHz Resolution Bandwidth for MHz) Quasi-Peak if maximised peak within 6dB of Quasi-Peak limit Operating Environment: E.U.T. Operation Temperature: 21.0 C Humidity: 48 % RH Atmospheric Pressure: 1006 mbar EUT Operation: Test the EUT with full function according to standard Measurement Data An initial pre-scan was performed on the live and neutral lines with peak detector. Quasi-Peak and Average measurement were performed at the frequencies with maximized peak emission were detected.

13 Page: 13 of 43 L line Receiver Receiver Frequency QP Limit Margin AV Limit Margin Level Level (MHz) (dbuv) (dbuv) (db) (dbuv) (dbuv) (db) 0.15 * * * * 0.50 * * * * 1.00 * * * * 1.40 * * * * 2.00 * * * * 3.50 * * * * 6.00 * * * * * * * * * * * * * * * * * means the emission level is 6dB lower than the relevant limit.

14 Page: 14 of 43 N line Receiver Receiver Frequency QP Limit Margin AV Limit Margin Level Level (MHz) (dbuv) (dbuv) (db) (dbuv) (dbuv) (db) 0.15 * * * * 0.50 * * * * 1.00 * * * * 1.40 * * * * 2.00 * * * * 3.50 * * * * 6.00 * * * * * * * * * * * * * * * *

15 Page: 15 of 43 * means the emission level is 6dB lower than the relevant limit. 6.2 Radiated Emissions (30MHz to 1GHz) Test Requirement: EN 55011: 2007/A2:2007 Test Method: EN 55011: 2007/A2:2007 Test Date: Jan. 08, 2009 Frequency Range: 30MHz to 1GHz Measurement Distance: 3m Class / Severity: Class A Limit: 50.0 dbµv/m between 30MHz & 230MHz 57.0 dbµv/m between 230MHz & 1GHz Detector: Peak for pre-scan (120kHz resolution bandwidth)

16 Page: 16 of 43 Quasi-Peak if maximised peak within 6dB of limit E.U.T. Operation Operating Environment: Temperature: 26 C Humidity: 50 % RH Atmospheric Pressure: 1004 mbar EUT Operation: The EUT is in representative work mode Measurement Data An initial pre-scan was performed in peak detection mode. Quasi-Peak was performed at the frequencies with maximized peak emission were detected. Horizontal:

17 Page: 17 of 43 Final Result 1 Frequency (MHz) QuasiPeak (dbuv/m) Meas. Time (ms) Bandwidth (khz) Antenna height (cm) Polarity Turntable position (deg) Corr. (db) Margin (db) Limit (dbuv /m) H H H H H H

18 Vertical : SGS-CSTC Standards Page: 18 of 43 Final Result 1 Frequency (MHz) QuasiPeak (dbuv/m) Meas. Time (ms) Bandwidth (khz) Antenna height (cm) Polarity Turntable position (deg) Corr. (db) Margin (db) Limit (dbuv/m) V V V V V V

19 Page: 19 of Harmonics Test Results Test Requirement: Test Method: Frequency Range: Test Class: EN : 2006+A1:2009+A2:2009 EN : 2006+A1:2009+A2:2009 Up to 2kHz Class A Test Date Jan. 11, Measurement Diagram and Data Average harmonic current results Hn Ieff [A] Ieff [%] Limit [A] Result E E PASS E PASS E E-3 PASS E PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS

20 Page: 20 of E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS Maximum harmonic current results Hn Ieff [A] Ieff [%] Limit [A] Result E E PASS E PASS E E-3 PASS E PASS E E-3 PASS E PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS E E-3 PASS

21 Page: 21 of Flicker Test Result Test Requirement: EN : 2008 Test Method: EN : 2008 Test Date: Jan. 11, 2009 Class/Severity: Clause 5 of EN Measurement Time: 2h Detector: As per EN Test Results: Pass Maximum Flicker results EUT values Limit Result Pst PASS Plt PASS dc [%] PASS dmax [%] PASS dt [s] PASS

22 Page: 22 of 43 7 Immunity Test Results 7.1 Performance Criteria Description in Clause 4 of EN :2005 Performance Criterion A: Performance Criterion B: Performance Criterion C: The apparatus shall continue to operate as intended during and after the test. No degradation of performance or loss of function is allowed below a performance level specified by the manufacturer, when the apparatus is used as intended. The performance level may be replaced by a permissible loss of performance. If the minimum performance level or the permissible performance loss is not specified by the manufacturer, either of these may be derived from the product description and documentation, and from what the user may reasonably expect from the apparatus if used as intended. The apparatus shall continue to operate as intended after the test. No degradation of performance or loss of function is allowed below a performance level specified by the manufacturer, when the apparatus is used as intended. The performance level may be replaced by a permissible loss of performance. During the test, degradation of performance is however allowed. No change of actual operating state or stored data is allowed. If the minimum performance level or the permissible performance loss is not specified by the manufacturer, either of these may be derived from the product description and documentation, and from what the user may reasonably expect from the apparatus if used as intended. Temporary loss of function is allowed, provided the function is self-recoverable or can berestored by the operation of the controls. 7.2 ESD Test Requirement: EN : 2005 Test Method: IEC :2001 Test Date: Jan. 12, 2009 Discharge Impedance: 330 Ω / 150 pf Discharge Voltage: Air Discharge: ±8 kv Polarity: Number of Discharge: Discharge Mode: Discharge Period: E.U.T. Operation Operating Environment: Contact Discharge: HCP: VCP: Positive & Negative ±4 kv ±4 kv ±4 kv Minimum 10 times at each test point for Contact and VCP Discharge;Minimum 10 times at each test point for Air Discharge Single Discharge 1 second minimum

23 Page: 23 of 43 Temperature: 23.0 C Humidity: 49 % RH Atmospheric Pressure: 1008 mbar EUT Operation: The EUT is in representative work mode Direct Application Test Results Observations: Test Point: 1. All insulated enclosure & seams around EUT. 2. All touchable metal material of EUT Direct Application Test Results Discharge Level (kv) Polarity (+/-) Test Points Contact Discharge Air Discharge 8 +/- 1 N/A A 4 +/- 2 A N/A Indirect Application Test Results Observations: Test Point: 1. All sides. Indirect Application Test Results Discharge Level (kv) Polarity (+/-) Test Point Horizontal Coupling Vertical Coupling 4 +/- 1 A A Results: A: No degradation in the performance of the EUT was observed. N/A: Not applicable (not required in the standard or floor moutned the EUT)

24 Page: 24 of Radio Frequency Electromagnetic Fields Test Test Requirement: EN : 2005 Test Method: IEC : 2008 Test Date: Jan. 12, 2009 Frequency Range: Test level: Modulation: Criteria: E.U.T. Operation 80MHz to 1GHz, 1.4GHz to 2GHz, 2GHz to 2.7GHz 80MHz to 1GHz,10V/m on enclosure 1.4GHz to 2GHz, 3V/m on enclosure 2GHz to 2.7GHz, 1V/m on enclosure 80%, 1kHz Amplitude Modulation Performance criteria A Operating Environment: Temperature: 23 C Humidity: 51 % RH Atmospheric Pressure: 1007 mbar EUT Operation: Test Results Pass The EUT is in representative work mode.

25 Page: 25 of Electrical Fast Transients (EFT) Test Requirement: EN : 2005 Test Method: IEC : 2004 Test Date: Jan. 12, 2009 Test Level: Polarity: Repetition Frequency: Burst Period: Test Duration: E.U.T. Operation ±2.0kV on AC Positive & Negative 5kHz 300ms 2 minute per level & polarity Operating Environment: Temperature: 21 C Humidity: 40 % RH Atmospheric Pressure: 1002 mbar EUT Operation: The EUT is in representative work mode Test Results On AC Supply: Lead under Test Level (±kv) Coupling Direct/Clamp L,N,PE ± 2.0 Direct A: No loss of function was observed. EUT operating mode On working mode Observations (Performance Criterion) (A)

26 Page: 26 of Surges Test Requirement: EN : 2005 Test Method: IEC :2005 Test Date: Jan. 12, 2009 Test Level: Polarity: Generator source impedance: Trigger Mode: ±1kV Line to Neutral, ±2kV Line to PE Positive & Negative 2Ω Line to Neutral, 12Ω Line to PE Internal No. of surges: 5 positive, 5 negative at 0, 90, 180, E.U.T. Operation Operating Environment: Temperature: 22.0 C Humidity: 50 % RH Atmospheric Pressure: 1017 mbar EUT Operation: The EUT is in representative work mode Test Results: Pass

27 Page: 27 of 43 Pulse No Line- Line Level (kv) Surge Interval Phase (deg) Observation (Performance Criterion) 1 5 L-N +1 60s 0 No loss of performance (A) 6 10 L-N -1 60s 0 (A) L-N +1 60s 90 (A) L-N -1 60s 90 (A) L-N +1 60s 180 (A) L-N -1 60s 180 (A) L-N +1 60s 270 (A) L-N -1 60s 270 (A) 1 5 L-PE +2 60s 0 (A) 6 10 L-PE -2 60s 0 (A) L-PE +2 60s 90 (A) L-PE -2 60s 90 (A) L-PE +2 60s 180 (A) L-PE -2 60s 180 (A) L-PE +2 60s 270 (A) L-PE -2 60s 270 (A) 1 5 N-PE +2 60s 0 (A) 6 10 N-PE -2 60s 0 (A) N-PE +2 60s 90 (A) N-PE -2 60s 90 (A) N-PE +2 60s 180 (A) N-PE -2 60s 180 (A) N-PE +2 60s 270 (A) N-PE -2 60s 270 (A)

28 Page: 28 of Injected Currents 0.15MHz to 80MHz Test Requirement: EN : 2005 Test Method: IEC :2006 Test Date: Jan. 12, 2009 Frequency Range: 0.15MHz to 80MHz Test level: 10V rms on AC Ports (unmodulated emf into 150 Ω) Modulation: E.U.T. Operation 80%, 1kHz Amplitude Modulation Operating Environment: Temperature: 22 C Humidity: 50 % RH Atmospheric Pressure: 1017 mbar EUT Operation: The EUT is in representative work mode Test Results: Frequency Line Test Level Modulation Step Size Dwell Time Observation (Performance Criterion) 150kHz to 80MHz 3 Wire AC Supply Cable 10Vrms 80%, 1kHz Amp. Mod. 1% 3S No Loss of Function (A)

29 Page: 29 of Voltage Dips and Interruptions Test Requirement: EN : 2005 Test Method: IEC :2004 Test Date: December 26, 2008 Test Level: No. of Dips / Interruptions: E.U.T. Operation 0% of U T (Supply Voltage) for 1 Periods 40% of U T (Supply Voltage) for 10 Periods 70 % of U T (Supply Voltage) for 25 Periods 0 % of U T (Supply Voltage) for 250 Periods 6 per Level Operating Environment: Temperature: 22 C Humidity: 50 % RH Atmospheric Pressure: 1017 mbar EUT Operation: Test the EUT with full function according to standard Test Results: EUT operating mode Dropout % U T Phase Duration of dropout in Periods No of dropout Time between dropout Observations (Performance Criterion) On mode s (A) On mode s (A) On mode s (A) On mode s (A) On mode s (B) On mode s (B) On mode s (B) On mode s (B) Performance C is within the acceptable criterion for Voltage Dips and Interruption test.

30 Page: 30 of 43

31 Page: 31 of 43 8 Photographs 8.1 Conducted Emission Test Setup 8.2 Radiated emission Test Setup

32 Page: 32 of Harmonic&Flicker Test Setup

33 Page: 33 of ESD Test Setup 8.5 Radio Frequency Electromagnetic Fields Test Setup

34 Page: 34 of Surge/ Voltage Dips And Interruptions Test Setup 8.7 EFT Test Setup

35 Page: 35 of Injected Currents Test Setup

36 Page: 36 of EUT Constructional Details

37 Page: 37 of 43

38 Page: 38 of 43

39 Page: 39 of 43

40 Page: 40 of 43

41 Page: 41 of 43

42 Page: 42 of 43

43 Page: 43 of 43 THE END OF REPORT