EN 55015: 2013 Clause Pass. EN 55015: 2013 Clause Pass. EN 55015: 2013 Clause Pass

Transcription

1

2 Reference No.: WTD15S E Page 2 of 42 1 Test Summary Test Item Conducted Disturbance at Mains Terminal, 9kHz to 30MHz Radiation electromagnetic disturbance, 9kHz to 30MHz Radiation Emission, 30MHz to 300MHz EMISSION Test Standard Class / Severity Result EN 55015: 2013 Clause Pass EN 55015: 2013 Clause Pass EN 55015: 2013 Clause Pass Harmonic Current emission EN : 2014 Class C N/A Voltage Fluction and Flicker EN : 2013 Clause 5 Pass IMMUNITY(EN 61547:2009) Test Item Test Method Class / Severity Electrostatic Discharge(ESD) IEC :2008 Radio-frequency electromagnetic fields (80MHz to 1GHz) IEC :2010 Electrical Fast Transients (EFT) IEC :2012 Surges IEC :2014 Injected Currents, 0.15MHz to 80MHz IEC :2013 ±4 kv Contact ±8 kv Air 3V/m, 80%, 1kHz, Amp. Mod. AC ±1.0kV DC ±0.5kV Signal Line ±0.5kV <25W: ±0.5kV D.M. ±1kV C.M. 25W: ±1kV D.M. ±2kV C.M. 3Vr.m.s.(emf), 80%, 1kHz Amp. Mod. Performance Criteria B A B B A Result Pass Pass Pass Pass Pass Power-frequency magnetic field IEC :2009 3A/m A N/A Voltage Dips and Interruptions IEC : % UT* for 0.5per B Pass 70 % UT* for 10per C Pass Remark: Pass Test item meets the requirement Fail Test item does not meet the requirement N/A Test case does not apply to the test object A.M Amplitude Modulation Differential Mode Common Mode * U T is the nominal supply voltage

3 Reference No.: WTD15S E Page 3 of 42 2 Contents Page COVER PAGE 1 1 TEST SUMMARY CONTENTS GENERAL INFORMATION GENERAL DESCRIPTION OF E.U.T DETAILS OF E.U.T STANDARDS APPLICABLE FOR TESTING TEST FACILITY SUBCONTRACTED ABNORMALITIES FROM STANDARD CONDITIONS EQUIPMENT USED DURING TEST EQUIPMENT LIST MEASUREMENT UNCERTAINTY EMISSION TEST RESULTS CONDUCTED DISTURBANCE AT MAINS TERMINAL RADIATION ELECTROMAGNETIC DISTURBANCE, 9KHZ TO 30MHZ RADIATION EMISSION, 30MHZ TO 300MHZ HARMONICS CURRENT EMISSION VOLTAGE FLUCTUATION AND FLICKER IMMUNITY TEST RESULTS PERFORMANCE CRITERIA ELECTROSTATIC DISCHARGE(ESD) RADIO-FREQUENCY ELECTROMAGNETIC FIELDS, 80MHZ TO 1GHZ ELECTRICAL FAST TRANSIENTS (EFT) SURGES INJECTED CURRENTS IMMUNITY 0.15MHZ TO 80MHZ VOLTAGE DIPS AND INTERRUPTIONS PHOTOGRAPHS TEST SETUP PHOTOGRAPH CONDUCTED DISTURBANCE AT MAINS TERMINAL TEST SETUP PHOTOGRAPH RADIATION ELECTROMAGNETIC DISTURBANCE TEST SETUP, 9KHZ TO 30MHZ PHOTOGRAPH RADIATION EMISSION TEST SETUP, 30MHZ TO 300MHZ PHOTOGRAPH VOLTAGE FLUCTUATION AND FLICKER TEST SETUP PHOTOGRAPH ESD IMMUNITY TEST SETUP PHOTOGRAPH RADIO-FREQUENCY ELECTROMAGNETIC FIELDS IMMUNITY TEST SETUP PHOTOGRAPH EFT&SURGES& VOLTAGE DIPS AND INTERRUPTIONS IMMUNITY TEST SETUP PHOTOGRAPH INJECTED CURRENTS IMMUNITY TEST SETUP PHOTOGRAPHS CONSTRUCTIONAL DETAILS EUT APPEARANCE VIEW... 37

4

5 Reference No.: WTD15S E Page 5 of 42 Waltek Services(Shenzhen) Co., Ltd. EMC Laboratory `has been registered and fully described in a report filed with the (FCC) Federal Communications Commission. The acceptance letter from the FCC is maintained in our files. Registration , December 3, Subcontracted Whether parts of tests for the product have been subcontracted to other labs: Yes No If Yes, list the related test items and lab information: Test Lab: N/A Lab address: N/A Test items: N/A 3.6 Abnormalities from Standard Conditions None.

6 Reference No.: WTD15S E Page 6 of 42 4 Equipment Used during Test 4.1 Equipment List Conducted Emissions at Mains Terminals Disturbance Voltage Item Equipment Manufacturer Model No. Serial No. Last Calibration Date Calibration Due Date 1. EMI Test Receiver R&S ESCI Sep.15, 2014 Sep.14, LISN SCHWARZBECK NSLK Sep.15, 2014 Sep.14, Limiter York MTS-IMP Sep.15, 2014 Sep.14, Cable LARGE RF300 - Sep.15, 2014 Sep.14, 2015 Radiation electromagnetic disturbance(9khz to 30MHz) Item Equipment Manufacturer Model No. Serial No. Last Calibration Date Calibration Due Date 1. EMI Test Receiver R&S ESCI Sep.15, 2014 Sep.14, LARGE LOOP ANTENNA Laplace RF Sep.15, 2014 Sep.14, Cable LARGE RF300 - Sep.15, 2014 Sep.14, m Semi-anechoic Chamber for Radiation Item Equipment Manufacturer Model No. Serial No. Last Calibration Date Calibration Due Date 1. Test Receiver R&S ESCI Apr.10, 2015 Apr.09, Trilog Broadband Antenna SCHWARZBECK VULB Apr.10, 2015 Apr.09, Amplifier Compliance pirection PAP Apr.10, 2015 Apr.09, 2016 systems inc 4. Cable HUBER+SUHNER CBL Apr.10, 2015 Apr.09, 2016 Harmonics and Flicker Measuring System Item Equipment Manufacturer Model No. Serial No. Last Calibration Date Calibration Due Date 1 Digital Power Analyzer SCHAFFNER CCN Jun.03,2015 Jun.02, Power Source SCHAFFNER NSG Jun.03,2015 Jun.02,2016 Electrostatic Discharge Item Equipment Manufacturer Model No. Serial No. 1 Electrostatic Discharge Simulator Last Calibration Date Calibration Due Date Em Test DITO V Oct.28, 2014 Oct.27, 2015

7 Reference No.: WTD15S E Page 7 of 42 Radio-frequency electromagnetic fields Item Equipment Manufacturer Model No. Serial No. Last Calibration Date Calibration Due Date 1 Signal Generater R&S SMB100A Sep.15, 2014 Sep.14, RF Power Amplifier R&S 3 Gestockte Breitband (S tacked ) Log.-per.Antenna BLWA /100/40D Sep.15, 2014 Sep.14, 2015 R&S STLP9128D 043 Sep.15, 2014 Sep.14, Power Meter R&S NRP Sep.15, 2014 Sep.14, 2015 Surge, EFT, Voltage dips and Interruption Item Equipment Manufacturer Model No. Serial No All Modules Generator Capacitive Coupling Clamp Signal and Data Line Coupling Network Last Calibration Date Calibration Due Date SCHAFFNER N/A N/A SCHAFFNER CDN Sep.15, 2014 Sep.14, 2015 SCHAFFNER CDN Sep.15, 2014 Sep.14, AC Power Supply TONGYUN DTDGC-4 - Sep.15, 2014 Sep.14, 2015 Conducted Immunity Item Equipment Manufacturer Model No. Serial No. Last Calibration Date Calibration Due Date 1 RF Generator TESEQ NSG Sep.15, 2014 Sep.14, CDN M-Type TESEQ CDN M Sep.15, 2014 Sep.14, EM-Clamp TESEQ KEMZ Sep.15, 2014 Sep.14, Attenuator 6dB TESEQ ATN Sep.15, 2014 Sep.14, Measurement Uncertainty Test Item Frequency Range Uncertainty Note Conducted Emission 9kHz~30MHz ±3.64dB (1) Radiation electromagnetic disturbance 9kHz~30MHz ±3.00dB (1) Radiation Emission 30MHz~300MHz ±5.03dB (1) (1)This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2.

8 Reference No.: WTD15S E Page 8 of 42 5 Emission Test Results 5.1 Conducted Disturbance at Mains Terminal Test Requirement... : EN Clause Test Method... : EN Clause 8 Test Result... : Pass Frequency Range... : 9kHz to 30MHz Class/Severity... : Table 2a of EN E.U.T. Operation Operating Environment: Temperature... : 25.5 C Humidity... : 52.6%RH Atmospheric Pressure... : 101.2kPa EUT Operation: Input Voltage... : AC 235V/50Hz, AC 225V/50Hz Operating Mode... : Working mode Remark... : The worst case is under condition AC 235V/50Hz and the data is shown as follow Block Diagram of Test Setup The Conducted Disturbance at Mains Terminal tests were performed in accordance with the EN m EUT Receiver PC System 0.8m 0.8m LISN :50Ω Terminator Measurement Data The maximised peak emissions from the EUT was scanned and measured for both the Live and Neutral Lines. Quasi-peak & average measurements were performed if peak emissions were within

9 Reference No.: WTD15S E Page 9 of 42 6dB of the average limit line Conducted Disturbance at Mains Terminal Test Data Live Line :

10 Reference No.: WTD15S E Page 10 of 42 Neutral Line :

11 Reference No.: WTD15S E Page 11 of Radiation Electromagnetic Disturbance, 9kHz to 30MHz Test Requirement... : EN Clause Test Method... : EN Clause 9.1 Test Result... : Pass Frequency Range... : 9kHz to 30MHz Class/Severity... : Table 3a of EN E.U.T. Operation Operating Environment: Temperature... : 25.5 C Humidity... : 53.3%RH Barometric Pressure... : 101.3kPa EUT Operation: Input Voltage... : AC 235V/50Hz, AC 225V/50Hz Operating Mode... : Working mode Remark... : The worst case is under condition AC 235V/50Hz and the data is shown as follow Block Diagram of Test Setup The Radiation Electromagnetic Disturbance (9kHz to 30MHz) test was performed in accordance with the EN m Loop Antenna EUT 1.5m coaxial change-over switch Test Receiver 0.5m Measurement Data The maximised peak emissions from the EUT was scanned and measured for the loop antenna three directions. Quasi-peak measurements were performed if peak emissions were within 6dB of the Quasi-peak limit line.

12 Reference No.: WTD15S E Page 12 of Radiation Electromagnetic Disturbance Test Data, 9kHz to 30MHz Loop X:

13 Reference No.: WTD15S E Page 13 of 42 Loop Y:

14 Reference No.: WTD15S E Page 14 of 42 Loop Z:

15 Reference No.: WTD15S E Page 15 of Radiation Emission, 30MHz to 300MHz Test Requirement... : EN Clause Test Method... : EN Annex B Test Result... : Pass Frequency Range... : 30MHz to 300MHz Class/Severity... : Table B.1 of EN Antenna polarisation.. : Horizontal& Vertical E.U.T. Operation Operating Environment: Temperature... : 24 C Humidity... : 54.3%RH Atmospheric Pressure... : 101.5kPa EUT Operation : Input Voltage... : AC 235V/50Hz, AC 225V/50Hz Operating Mode... : Working mode Remark... : The worst case is under condition AC 235V/50Hz and the data is shown as follow Block Diagram of Setup The Radiation Emission test was performed in accordance with EN Annex B. Semi-anechoic 3m Chamber Antenna Elevation Varies From 1 to 4 m Turn Table From 0 to 360 3m EUT 0.8m Turn Table PC System Spectrum Analyzer AMP Combining Network

16 Reference No.: WTD15S E Page 16 of Measurement Data The maximised peak emissions from the EUT was scanned and measured for both the Antenna Vertical Polarization and Antenna Horizontal Polarization. Quasi-peak measurements were performed if peak emissions were within 6dB of the Quasi-peak limit line Radiation Emission Test Data, 30MHz to 300MHz Antenna Polarization: Vertical

17 Reference No.: WTD15S E Page 17 of 42 Antenna Polarization: Horizontal

18 Reference No.: WTD15S E Page 18 of Harmonics Current Emission Test Requirement... : EN Test Method... : EN Test Result... : N/A Class/Severity... : Class C Remark... : This equipment uses symmetrical control method and the rated power is less than 25W. According to section 7 of EN , tests need not be made on equipment.

19 Reference No.: WTD15S E Page 19 of Voltage Fluctuation and Flicker Test Requirement... : EN Test Method... : EN Test Result... : Pass E.U.T. Operation Operating Environment: Temperature... : 25 C Humidity... : 54.2%RH Barometric Pressure... : 101.1kPa EUT Operation: Input Voltage... : AC 230V/50Hz Operating Mode... : Working mode Block Diagram of Setup The Voltage Fluctuation and Flicker test was performed in accordance with the EN EUT AC Mains Power Analyzer AC Source 80cm

20 Reference No.: WTD15S E Page 20 of Voltage Fluctuation and Flicker Test Data

21 Reference No.: WTD15S E Page 21 of 42 6 Immunity Test Results 6.1 Performance Criteria Performance criterion A: During the test, no change of the Iuminous intensity shall be observed and the regulating control, if any, shall operate during the test as intended. Performance criterion B: During the test, the Iuminous intensity may change to any value. After the test, the Iuminous intensity shall be restored to its initial value within 1 min. Regulating controls need not function during the test, but after the test, the mode of the control shall be the same as before the test provided that during the test no mode changing commands were given. Performance criterion C: During and after the test, any change of the luminous intensity is allowed and the lamp(s) may be extinguished. After the test, within 30 min, all functions shall return to normal, if necessary by temporary interruption of the mains supply and/or operating the regulating control.

22 Reference No.: WTD15S E Page 22 of Electrostatic Discharge(ESD) Test Requirement... : EN Test Method... : IEC Test Result... : Pass Discharge Impedance... : 330Ω / 150pF Discharge Voltage... : Air Discharge: ±8kV Contact Discharge: ±4kV HCP & VCP: ±4kV Polarity... : Positive & Negative Number of Discharge... : Minimum 10 times at each test point Discharge Mode... : Single Discharge Discharge Period... : 1 second minimum E.U.T. Operation Operating Environment: Temperature... : 24.5 C Humidity... : 53.1%RH Barometric Pressure... : 100.8kPa EUT Operation: Input Voltage... : AC 230V/50Hz Operating Mode... : Working mode Block Diagram of Setup The ESD test was performed in accordance with the IEC >1.0m 0.1m Vertical Coupling Plane ESD Generator EUT insulating support 470k ohm Wall 470k ohm Horizontal Coupling Plane 0.8m 470k ohm 470k ohm

23 Reference No.: WTD15S E Page 23 of Direct Discharge Test Results Observations: Test points: 1. All Exposed Surface & Seams; 2. All metallic part Applied Voltage (kv) Direct Discharge Performance Criterion Test Results Test Point Contact Discharge Air Discharge ±8 B 1 N/A Pass* ±4 B 2 Pass* N/A Remark: * During the test no deviation was detected to the selected operation mode(s) Indirect Discharge Test Results Observations: Applied Voltage (kv) Test points: 1. All sides. Indirect Discharge Performance Criterion Test Point Test Results Horizontal Coupling Vertical Coupling ±4 B 1 Pass* Pass* Remark: * During the test no deviation was detected to the selected operation mode(s)

24 Reference No.: WTD15S E Page 24 of Radio-frequency electromagnetic fields, 80MHz to 1GHz Test Requirement... : EN Test Method... : IEC Test Result... : Pass Frequency Range... : 80MHz to 1GHz Test level... : 3V/m Modulation... : 80%, 1kHz Amplitude Modulation. Face of EUT... : Front, Back, Left, Right Antenna polarisation... : Horizontal& Vertical E.U.T. Operation Operating Environment: Temperature... : 26 C Humidity... : 52.4% RH Barometric Pressure... : 102.4kPa EUT Operation: Input Voltage... : AC 230V/50Hz Operating Mode... : Working mode Block Diagram of Setup The Radio-frequency electromagnetic fields Immunity test was performed in accordance with the IEC Anechoic Chamber 3m Gestockte Breitband ( S tacked ) Log.-per.Antenna EUT Camera 0.8m Absorbers 1.5m Signal Generator RF- Amplifier

25 Reference No.: WTD15S E Page 25 of Test Results Frequency 80 to 1000MHz 80 to 1000MHz Face of EUT Front, Back, Left, Right Front, Back, Left, Right Antenna polarisation Test Level Step Size Dwell Time Performanc e Criterion Result Horizontal 3V/m 1% 1s A Pass* Vertical 3V/m 1% 1s A Pass* Remark: * During the test no deviation was detected to the selected operation mode(s)

26 Reference No.: WTD15S E Page 26 of Electrical Fast Transients (EFT) Test Requirement... : EN Test Method... : IEC Test Result... : Pass Polarity... : Positive & Negative Repetition Frequency... : 5kHz Burst Duration... : 300ms Test Duration... : 2 minutes per level & polarity E.U.T. Operation Operating Environment: Temperature... : 25 C Humidity... : 53.5%RH Barometric Pressure... : 102.3kPa EUT Operation: Input Voltage... : AC 230V/50Hz Operating Mode... : Working mode Block Diagram of Setup The Electrical Fast Transients Immunity test was performed in accordance with IEC For AC Mains or DC Ports: >0.5m Wall 0.1m wood table EUT Test AC Mains Generator For Signal and Control Ports: >0.5m Wall 0.1m wood table EUT Test AC Mains Clamp Generator

27 Reference No.: WTD15S E Page 27 of Test Results Test Ports AC Mains (Live-Neutral) Test Level(kV) Signal ±0.5 Performance Criterion Result ±1.0 B PASS * B N/A a * DC Ports ±0.5 B N/A * Remark: * During the test no deviation was detected to the selected operation mode(s) a Applicable only to cables which according to the manufacturer s specification supports communication on cable lengths greater than 3 m.

28 Reference No.: WTD15S E Page 28 of Surges Test Requirement... : EN Test Method... : IEC Test Result... : Pass Interval... : 60s between each surge No. of surges... : 5 positive at 90, 5 negative at E.U.T. Operation Operating Environment: Temperature... : 25.5 C Humidity... : 53.1%RH Barometric Pressure. : 101.2kPa EUT Operation: Input Voltage... : AC 230V/50Hz Operating Mode... : Working mode Block Diagram of Setup The Surge Immunity test was performed in accordance with the IEC >0.5m Wall 0.1m wood table EUT AC Mains Test Generator AC Mains Test Results Test Port AC Mains (Between Live And Neutral) AC Mains (Between Live And Earth) AC Mains (Between Neutral And Earth) Applied Voltage (kv) Performance criterion Result ±0.5 B PASS * ±1 B N/A * ±1 B N/A * Remark: * During the test no deviation was detected to the selected operation mode(s)

29 Reference No.: WTD15S E Page 29 of Injected Currents Immunity 0.15MHz to 80MHz Test Requirement... : EN Test Method... : IEC Test Result... : Pass Frequency Range... : 0.15MHz to 80MHz Test level... : 3V r.m.s. (unmodulated emf into 150 Ω) Modulation... : 80%, 1kHz Amplitude Modulation E.U.T. Operation Operating Environment: Temperature... : 24.9 C Humidity... : 51.2% RH Barometric Pressure : 103.2kPa EUT Operation: Input Voltage... : AC 230V/50Hz Operating Mode... : Working mode Block Diagram of Setup The Injected Currents Immunity test was performed in accordance with IEC For AC Mains or DC Port: 0.1m< L <0.3m 0.1m Wood Table EUT CDN AC Mains Attenuator 6dB Signal Generator Power Amplifier For Signal or Control Ports: 0.1m wood table EUT Attenuator 6dB Clamp Signal Generator Power Amplifier

30 Reference No.: WTD15S E Page 30 of Test Results Line Test Level Modulation Step Size Dwell Time Criterion Required Observations AC mains 3Vrms 80%, 1kHz Amp. Mod. 1% 1s A A * DC Line 3Vrms 80%, 1kHz Amp. Mod. 1% 1s A N/A Signal Line 3Vrms 80%, 1kHz Amp. Mod. 1% 1s A N/A a Control Line 3Vrms 80%, 1kHz Amp. Mod. 1% 1s A N/A a Remark: * During the test no deviation was detected to the selected operation mode(s) a Applicable only to cables which according to the manufacturer s specification supports communication on cable lengths greater than 3 m.

31 Reference No.: WTD15S E Page 31 of Voltage Dips and Interruptions Test Requirement... : EN Test Method... : IEC Test Result... : Pass Test Level(Voltage reduction) : 0%&70 % of U T (Supply Voltage) No. of Dips / Interruptions... : 1 per Level at 20ms intervals E.U.T. Operation Operating Environment: Temperature... : 24.5 C Humidity... : 53.7%RH Barometric Pressure... : 102.4kPa EUT Operation: Input Voltage... : AC 230V/50Hz Operating Mode... : Working mode Block Diagram of Setup The Voltage Dips and Interruptions Immunity test was performed in accordance with the IEC EUT AC Mains Test Generator AC Mains Test Results Test Level in%u T Phase Performance criterion Duration Result Pass* B Pass* 0 Pass* C Pass* Remark: * During the test no deviation was detected to the selected operation mode(s)

32 Reference No.: WTD15S E Page 32 of 42 7 Photographs Test Setup 7.1 Photograph Conducted Disturbance at Mains Terminal Test Setup 7.2 Photograph Radiation electromagnetic disturbance Test Setup, 9kHz to 30MHz

33 Reference No.: WTD15S E Page 33 of Photograph Radiation Emission Test Setup, 30MHz to 300MHz 7.4 Photograph Voltage Fluctuation and Flicker Test Setup

34 Reference No.: WTD15S E Page 34 of Photograph ESD Immunity Test Setup 7.6 Photograph Radio-frequency electromagnetic fields Immunity Test Setup

35 Reference No.: WTD15S E Page 35 of Photograph EFT&Surges& Voltage Dips and Interruptions Immunity Test Setup

36 Reference No.: WTD15S E Page 36 of Photograph Injected Currents Immunity Test Setup

37 Reference No.: WTD15S E Page 37 of 42 8 Photographs Constructional Details 8.1 EUT Appearance View

38 Reference No.: WTD15S E Page 38 of 42

39 Reference No.: WTD15S E Page 39 of 42

40 Reference No.: WTD15S E Page 40 of 42

41 Reference No.: WTD15S E Page 41 of 42

42 Reference No.: WTD15S E Page 42 of 42 ======End of Report======